Biofilm promoted current generation of Pseudomonas aeruginosa microbial fuel cell via improving the interfacial redox reaction of phenazines

High-performance anode electrocatalyst of MnCo2S4-Co4S3/bamboo charcoal for stimulating power generation in microbial fuel cell

Microbial fuel cell (MFC) is a promising technology for recovering energy in wastewater through bacterial metabolism. However, it always suffers from low power density and electron transfer efficiency, restricting the application. This study fabricated the MnCo2S4-Co4S3/bamboo charcoal (MCS-CS/BC) through an easy one-step hydrothermal method, and the material was applied to carbon felt (CF) to form high-performance MFC anode. MCS-CS/BC-CF anode exhibited lower Rct (10.1 Ω) than BC-CF (17.24 Ω) and CF anode (116.1 Ω), exhibiting higher electrochemical activity. MCS-CS/BC-CF anode promoted the electron transfer rate and resulted in enhanced power density, which was 9.27 times higher (980 mW m-2) than the bare CF (105.7 mW m-2). MCS-CS/BC-CF anode showed the best biocompatibility which attracted distinctly larger biomass (146.27 mg/μL) than CF (20 mg/μL) and BC-CF anode (20.1 mg/μL). The typical exoelectrogens (Geobacter and etc.) took dramatically higher proportion on MCS-CS/BC-CF anode (59.78%) than CF (2.99%) and BC-CF anode (26.67%). In addition, MCS-CS/BC stimulated the synergistic effect between exoelectrogens and fermentative bacteria, greatly favouring the extracellular electron transfer rate between bacteria and the anode and the power output. This study presented an efficient way of high-performance anode electrocatalyst fabrication for stimulating MFC power generation, giving suggestions for high-efficient energy recovery from wastewater.

Engineering extracellular electron transfer pathways of electroactive microorganisms by synthetic biology for energy and chemicals production

The excessive consumption of fossil fuels causes massive emission of CO2, leading to climate deterioration and environmental pollution. The development of substitutes and sustainable energy sources to replace fossil fuels has become a worldwide priority. Bio-electrochemical systems (BESs), employing redox reactions of electroactive microorganisms (EAMs) on electrodes to achieve a meritorious combination of biocatalysis and electrocatalysis, provide a green and sustainable alternative approach for bioremediation, CO2 fixation, and energy and chemicals production. EAMs, including exoelectrogens and electrotrophs, perform extracellular electron transfer (EET) (i.e., outward and inward EET), respectively, to exchange energy with the environment, whose rate determines the efficiency and performance of BESs. Therefore, we review the synthetic biology strategies developed in the last decade for engineering EAMs to enhance the EET rate in cell-electrode interfaces for facilitating the production of electricity energy and value-added chemicals, which include (1) progress in genetic manipulation and editing tools to achieve the efficient regulation of gene expression, knockout, and knockdown of EAMs; (2) synthetic biological engineering strategies to enhance the outward EET of exoelectrogens to anodes for electricity power production and anodic electro-fermentation (AEF) for chemicals production, including (i) broadening and strengthening substrate utilization, (ii) increasing the intracellular releasable reducing equivalents, (iii) optimizing c-type cytochrome (c-Cyts) expression and maturation, (iv) enhancing conductive nanowire biosynthesis and modification, (v) promoting electron shuttle biosynthesis, secretion, and immobilization, (vi) engineering global regulators to promote EET rate, (vii) facilitating biofilm formation, and (viii) constructing cell-material hybrids; (3) the mechanisms of inward EET, CO2 fixation pathway, and engineering strategies for improving the inward EET of electrotrophic cells for CO2 reduction and chemical production, including (i) programming metabolic pathways of electrotrophs, (ii) rewiring bioelectrical circuits for enhancing inward EET, and (iii) constructing microbial (photo)electrosynthesis by cell-material hybridization; (4) perspectives on future challenges and opportunities for engineering EET to develop highly efficient BESs for sustainable energy and chemical production. We expect that this review will provide a theoretical basis for the future development of BESs in energy harvesting, CO2 fixation, and chemical synthesis.

Electrobiochemical skills of Pseudomonas aeruginosa species that produce pyocyanin or pyoverdine for glycerol oxidation in a microbial fuel cell

Pseudomonas aeruginosa can produce pigments, which mediate external electron transfer (EET). Depending on the mediator, this species can be explored in bioelectrosystems to harvest energy or to obtain chemicals from residual organic compounds. This study has compared the performance of microbial fuel cells (MFCs) inoculated with a Pseudomonas aeruginosa isolate, namely EW603 or EW819, which produce pyocyanin and pyoverdine, respectively. The efficiency of these MFCs in glycerol, a typical residue of biodiesel production, were also compared. The MFCs exhibited different performances. The maximum voltage was 411 and 281 mV m², the power density was 40.1 and 21.3 mW m^-2, and the coulombic efficiency was 5.16 and 1.49% for MFC-EW603 and MFC-EW819, respectively. MFC-EW603 and MFC-EW819 achieved maximum current at 560 and 2200 Ω, at 141.2 and 91.3 mA m^-2, respectively. When the system was operated at the respective maximum current output, MFC-EW603 consumed the total glycerol content (11 mmol L^-1), and no products could be detected after 50 h. In turn, acetic and butyric acids were detected at the end of MFC-EW819 operation (75 h). The results suggested that P. aeruginosa metabolism can be steered in the MFC to generate current or microbial products depending on the pigment-producing strain and the conditions applied to the system, such as the external resistance. In addition, gene cluster pathways related to phenazine production (phzA and phzB) and other electrogenic-related genes (mexGHI-opmB) were identified in the strain genomes, supporting the findings. These results open new possibilities for using glycerol in bioelectrochemical systems.

Enhanced bio-electrochemical performance of microbially catalysed anode and cathode in a microbial electrosynthesis system

Most bio-electrochemical systems (BESs) use biotic/abiotic electrode combinations, with platinum-based abiotic electrodes being the most common. However, the non-renewability, cost, and poisonous nature of such electrode systems based on noble metals are major bottlenecks in BES commercialisation. Microbial electrosynthesis (MES), which is a sustainable energy platform that simultaneously treats wastewater and produces chemical commodities, also faces the same problem. In this study, a dual bio-catalysed MES system with a biotic anode and cathode (MES-D) was tested and compared with a biotic cathode/abiotic anode system (MES-S). Different bio-electrochemical tests revealed improved BES performance in MES-D, with a 3.9-fold improvement in current density compared to that of MES-S. Volatile fatty acid (VFA) generation also increased 3.2-, 4.1-, and 1.8-fold in MES-D compared with that in MES-S for acetate, propionate, and butyrate, respectively. The improved performance of MES-D could be attributed to the microbial metabolism at the bioanode, which generated additional electrons, as well as accumulative VFA production by both the bioanode and biocathode chambers. Microbial community analysis revealed the enrichment of electroactive bacteria such as Proteobacteria (60%), Bacteroidetes (67%), and Firmicutes + Proteobacteria + Bacteroidetes (75%) on the MES-S cathode and MES-D cathode and anode, respectively. These results signify the potential of combined bioanode/biocathode BESs such as MES for application in improving energy and chemical commodity production.

Enhanced power generation, organics removal and water desalination in a microbial desalination cell (MDC) with flow electrodes

This study introduced a flow electrode microbial desalination cell (FE-MDC), which used activated carbon (AC) particles and carbon nanotubes (CNTs) as the electrode to promote electron harvesting. The recovered electricity energy (0.371 KWh/m³) and columbic efficiency (66.7 %) of the FE-MDC were over 2 times higher than those of the conventional MDC without the flow electrode. Consequently, the salt and COD removal efficiencies were enhanced to 77.8 % and 91.2 %, respectively. Electrochemical analysis implied that the charge transfer resistance of the system was reduced by the flow electrode. Electron accumulation and charging-discharging experiments proved that the flow electrode could accumulate electrons and transfer the electrons to the fixed anode. Bacterial community analysis indicated that the bacterial activity was improved by the flow electrode. The content of the exoelectrogen Pseudomonas increased from 5.0 % to 14.7 %, and Hydrogenophaga improved from 1.4 % to 5.9 %. Finally, a continuous operation mode of the FE-MDC was established, and the flow electrode slurry was returned to the anodic chamber for recirculated utilization. The voltage output, COD removal, and salt removal during the operation mode reached 610 mV, 78.8 %, and 76.1 %, respectively. This study proved that the flow electrode is a promising way to promote the practical application of MDC technology.

The parallel electron transfer pathways of biofilm and self-secreted electron shuttles in gram-positive strain Rhodococcus pyridinivorans HR-1 inoculated microbial fuel cell

Microbial fuel cell (MFC) exhibits huge potentials in disposing wastewater and extra energy consumption. Exploring useful microorganisms for MFC is the crucial section. Herein, the electrochemical mechanism of extracellular anaerobic respiration in MFC inoculated with gram-positive Rhodococcus pyridinivorans HR-1, was first revealed. The MFC exhibited rapid recovery of currents on anode, and could recover to maximum output within one hour, with redox peaks near -0.38 and -0.18 V through electron transfer between the biofilm and anode. When the biofilm-based pathway was blocked by wrapping the anode with Millipore filter membrane, HR-1 inoculated MFC could still generate electricity within a longer recovery period (∼35 h) during anolyte exchange. This was proposed as a self-secreted electron shuttle pathway for electron transfer in R. pyridinivorans HR-1. Cyclic voltammetry analysis revealed that the biofilm-based and self-secreted electron shuttle-based pathways co-existed in R. pyridinivorans HR-1 inoculated MFC, which could play synergistic roles in electricity generation.

Complete genome sequence of Pseudomonas stutzeri S116 owning bifunctional catalysis provides insights into affecting performance of microbial fuel cells

Background

Pseudomonas stutzeri S116 is a sulfur-oxidizing bacteria isolated from marine sludge. It exhibited excellent electricity generation as bioanode and biocathode applied in microbial fuel cells (MFCs). Complete genome sequencing of P. stutzeri and cyclic voltammetry method were performed to reveal its mechanism in microbial fuel cells system.

Results

This study indicated that the MFCs generated a maximum output voltage of 254.2 mV and 226.0 mV, and maximum power density of 765 mW/m² and 656.6 mW/m² respectively. Complete genome sequencing of P. stutzeri S116 was performed to indicate that most function genes showed high similarities with P. stutzeri, and its primary annotations were associated with energy production and conversion (6.84%), amino acid transport and metabolism (6.82%) and inorganic ion transport and metabolism (6.77%). Homology of 36 genes involved in oxidative phosphorylation was detected, which suggests the strain S116 possesses an integrated electron transport chain. Additionally, many genes encoding pilus-assembly proteins and redox mediators (riboflavin and phenazine) were detected in the databases. Thiosulfate oxidization and dissimilatory nitrate reduction were annotated in the sulfur metabolism pathway and nitrogen metabolism pathway, respectively. Gene function analysis and cyclic voltammetry indicated that P. stutzeri probably possesses cellular machinery such as cytochrome c and redox mediators and can perform extracellular electron transfer and produce electricity in MFCs.

Conclusion

The redox mediators secreted by P. stutzeri S116 were probably responsible for performance of MFCs. The critical genes and metabolic pathways involved in thiosulfate oxide and nitrate reduction were detected, which indicated that the strain can treat wastewater containing sulfide and nitrite efficiently.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12866-022-02552-8.

Evaluation of extracellular electron transfer in Pseudomonas aeruginosa by co-expression of intermediate genes in NAD synthetase production pathway

Pseudomonas aeruginosa (PA) is an electrogenic bacterium, in which extracellular electron transfer (EET) is mediated by microbially-produced phenazines, especially pyocyanin. Increasing EET rate in electrogenic bacteria is key for the development of biosensors and bioelectrofermentation processes. In this work, the production of pyocyanin, Nicotinamide Adenine Dinucleotide (NAD) and NAD synthetase by the electrogenic strain PA-A4 is determined using a Microbial Fuel Cell (MFC). Effects of metabolic inhibition and enhancement of pyocyanin and NAD synthetase on NAD/NADH levels and electrogenicity was demonstrated by short chronoamperometry measurements (0-48 h). Combined overexpression of two intermediate NAD synthetase production genes-nicotinic acid mononucleotide adenyltransferase (nadD) and quinolic acid phosphoribosyltransferase (nadC) genes, which are distant on the PA genomic map, enabled co-transcription and increased NAD synthetase activity. The resulting PA-A4 nadD + nadC shows increases in pyocyanin concentration, NAD synthetase activity, NAD/NADH levels, and MFC potential, all significantly higher than its wild type. Extracellular respiratory mechanisms in PA are linked with NAD metabolism, and targeted increased yield of NAD could directly lead to enhanced EET. A previous attempt at enhancing NAD synthetase for electrogenicity by targeting the terminal NAD synthetase gene (nadE) in standard P. aeruginosa PA01 had earlier been reported. Our work however, poses another route to electrogenicity enhancement in PA using; a combination of nadD and nadC. Further experiments are needed to understand specific intracellular mechanisms governing how over-expression of nadD and nadC induced activity of NadE protein. These findings significantly advance the knowledge of the versatility of NAD biosynthetic genes in PA electrogenicity.

A Short Overview of Biological Fuel Cells

This short review summarizes the improvements on biological fuel cells (BioFCs) with or without ionomer separation membrane. After a general introduction about the main challenges of modern energy management, BioFCs are presented including microbial fuel cells (MFCs) and enzymatic fuel cells (EFCs). The benefits of BioFCs include the capability to derive energy from waste-water and organic matter, the possibility to use bacteria or enzymes to replace expensive catalysts such as platinum, the high selectivity of the electrode reactions that allow working with less complicated systems, without the need for high purification, and the lower environmental impact. In comparison with classical FCs and given their lower electrochemical performances, BioFCs have, up to now, only found niche applications with low power needs, but they could become a green solution in the perspective of sustainable development and the circular economy. Ion exchange membranes for utilization in BioFCs are discussed in the final section of the review: they include perfluorinated proton exchange membranes but also aromatic polymers grafted with proton or anion exchange groups.

Synergistic degradation for o-chlorophenol and enhancement of power generation by a coupled photocatalytic-microbial fuel cell system

A hierarchically photocatalytic microbial fuel cell system (PMFC) coupled with TiO₂ photoanode and bioanode was established to enhance the power generation based on single-chamber MFC. Compared with the conventional anaerobic mode, oxygen in the solution could be utilized by the photoanode of PMFC to improve the removal of o-chlorophenol (2-CP). The maximum power densities were increasing from 261 (MFC) to 301 mW/m² (PMFC). The removal efficiency of 2-CP (5 mg/L) in PMFC was 76.20% and higher than that in MFC (19.33%) and by photocatalysis (49.23%). The electron-hole separation efficiencies were decreasing with the increasing of dissolved oxygen, causing a low efficiency of photocatalysis, due to the reduction of the current density of the systems. The abundance of Geobacter sp., PHOS-HE36 fam., and Pseudomonas sp. was increased with illumination, contributing to improve the electricity production and 2-CP degradation. The only detective intermediate of 1,2-dichlorobenzene in PMFC indicated that the microbes could regulate the degradation pathway of 2-CP in the coupling system. These findings provided an feasible method for the effective degradation of refractory organic compounds and simultaneous energy recovery by combining photocatalysis and microbial power generation.

Review on microbial fuel cells applications, developments and costs

The microbial fuel cell (MFC) technology has attracted significant attention in the last years due to its potential to recover energy in a wastewater treatment. The idea of using an MFC in industry is very attractive as the organic wastes can be converted into energy, reducing the waste disposal costs and the energy needs while increasing the company profit. However, taking aside these promising prospects, the attempts to apply MFCs in large-scale have not been succeeded so far since their lower performance and high costs remains challenging. This review intends to present the main applications of the MFC systems and its developments, particularly the advances on configuration and operating conditions. The diagnostic techniques used to evaluate the MFC performance as well as the different modeling approaches are described. Towards the introduction of the MFC in the market, a cost analysis is also included. The development of low-cost materials and more efficient systems, with high higher power outputs and durability, are crucial towards the application of MFCs in industrial/large scale. This work is a helpful tool for discovering new operation and design regimes.

Bioelectricity generation using long-term operated biocathode: RFLP based microbial diversity analysis

In the present work, power generation and substrate removal efficiencies of long-term operated microbial fuel cells, containing abiotic cathodes and biocathodes, were evaluated for 220 days. Among the two microbial fuel cell (MFC) types, the one containing biocathode showed higher power density (54 mW/m2), current density (122 mA/m2) coulombic efficiency (33%), and substrate removal efficiency (94%) than the abiotic cathode containing MFC. Voltammetric analysis also witnessed higher and sustainable electron discharge for the MFC with biocathode, when compared with the abiotic cathode MFC. Over the tested period, both MFC have shown a cell voltage drop, after 150 and 165, days, for the MFC with biocathode and abiotic cathodes, respectively. Polymerase chain reaction (PCR) based restriction fragment length polymorphism (RFLP) analysis identified 281 clones. Bacteria belonging to Acinetobacter, Acidovorax, Pseudomonas and Burkholderia were observed in the abiotic cathode MFC. Bacteria belonging to Geobacter, Cupriavidus and Acidobacteria were observed in the biocathode MFC. Almost similar types of archaea (Methanosarcinales, Methanolinea, Nitrososphaera and Methanomicrobiales) were observed in both MFCs.

Use of Biochar-Based Cathodes and Increase in the Electron Flow by Pseudomonas aeruginosa to Improve Waste Treatment in Microbial Fuel Cells

In this paper, we tested the combined use of a biochar-based material at the cathode and of Pseudomonas aeruginosa strain in a single chamber, air cathode microbial fuel cells (MFCs) fed with a mix of shredded vegetable and phosphate buffer solution (PBS) in a 30% solid/liquid ratio. As a control system, we set up and tested MFCs provided with a composite cathode made up of a nickel mesh current collector, activated carbon and a single porous poly tetra fluoro ethylene (PTFE) diffusion layer. At the end of the experiments, we compared the performance of the two systems, in the presence and absence of P. aeruginosa, in terms of electric outputs. We also explored the potential reutilization of cathodes. Unlike composite material, biochar showed a life span of up to 3 cycles of 15 days each, with a pH of the feedstock kept in a range of neutrality. In order to relate the electric performance to the amount of solid substrates used as source of carbon and energy, besides of cathode surface, we referred power density (PD) and current density (CD) to kg of biomass used. The maximum outputs obtained when using the sole microflora were, on average, respectively 0.19 Wm−2kg−1 and 2.67 Wm−2kg−1, with peaks of 0.32 Wm−2kg−1 and 4.87 Wm−2kg−1 of cathode surface and mass of treated biomass in MFCs with biochar and PTFE cathodes respectively. As to current outputs, the maximum values were 7.5 Am−2 kg−1 and 35.6 Am−2kg−1 in MFCs with biochar-based material and a composite cathode. If compared to the utilization of the sole acidogenic/acetogenic microflora in vegetable residues, we observed an increment of the power outputs of about 16.5 folds in both systems when we added P. aeruginosa to the shredded vegetables. Even though the MFCs with PTFE-cathode achieved the highest performance in terms of PD and CD, they underwent a fouling episode after about 10 days of operation, with a dramatic decrease in pH and both PD and CD. Our results confirm the potentialities of the utilization of biochar-based materials in waste treatment and bioenergy production.

The identification and performance assessment of dominant bacterial species during linear alkylbenzene sulfonate (LAS)-biodegradation in a bioelectrochemical system

The anionic surfactant linear alkylbenzene sulfonate (LAS) is a major chemical constituent of detergent formulation. Regarding the recalcitrant nature of sulfonoaromatic compounds, discharging these substances into wastewater collection systems is a real environmental issue. A study on LAS biodegradation based on bioelectrochemical treatment and in the form of developing a single-chamber microbial fuel cell with air cathode is reported in the present work. Pretreatment study showed LAS concentration of 60 ppm resulted in the highest anaerobic LAS removal of 57%; so, this concentration was chosen to run the MFC. After the sustained anodic biofilm was formed, LAS degradation rate during 4 days in MFC was roughly 76% higher than that in the serum bottle, which indicated the role of the bioelectrochemical process in improving anaerobic LAS removal. Additionally, through 16S rRNA gene sequencing, the dominant bacterial species in the biofilm was identified as Pseudomonas zhaodongensis NEAU-ST5-21(T) with about 98.9% phylogenetic similarity and then a pathway was proposed for LAS anaerobic biodegradation. The MFC characteristics were assessed by pH monitoring as well as scanning electron microscopy and current density evolution.

Onset Investigation on Dynamic Change of Biohythane Generation and Microbial Structure in Dual-chamber versus Single-chamber Microbial Electrolysis Cells

Biohythane is alternative fuel to replace fossil fuel for car combustion, and biohythane generation could be potential pathway for energy recovery from wastewater treatment. Microbial electrolysis cell (MEC) is electrochemical technique to convert waste to methane and hydrogen gas for biohythane generation, but the feasibility and stability of MEC needs further investigation to assure sustainable energy recovery. System configuration is paramount factor for electrochemical reaction and mass transfer, and this study was to investigate the configuration impact (single vs dual chamber) of MEC for biohythane generation rate and stability. This study showed that dual-chamber MEC could separate methane and hydrogen gas production in the anode and cathode, and combined both together to produce biohythane. To reduce ohmic resistance for higher current, cation exchange membrane (CEM) was removed from dual-chamber to single-chamber MEC. However, free hydrogen diffusion was allowed in the single chamber since CEM was removed. The diffused hydrogen and substrate towards the cathode would favor the methanogen growth, and thus the hydrogen was consumed to reduce the biohythane generation and energy recovery efficiency (i.e., 7.5 × 10^-3 reduced to 5.7 × 10^-3 kWh kg^-1 degraded COD day^-1 after converting dual-chamber to single-chamber MEC). Absolute abundance of methanogen in single-chamber MEC was greatly boosted, as Methanosarcina and Methanobacteriale on the anode surface, increased by 132% and 243%, respectively, while the original dual-chamber MEC could maintain Geobacter growth for high current generation. This is the keystone study to demonstrate the importance of dual-chamber MEC for the feasibility and stability for the biohythane generation, building up the foundation to use electrochemical device to convert the organic waste to the alternative biohythane.

Antimicrobial resistance and virulence characteristics in ERIC-PCR typed biofilm forming isolates of P. aeruginosa

Pseudomonas aeruginosa is a serious pathogen particularly in immunocompromised patients. In this work, 103 clinical isolates of P. aeruginosa were collected and classified into weak, moderate, and strong biofilm producers according to their biofilm forming abilities via tissue culture plate method. The antimicrobial resistance and the presence of different virulence genes were investigated via disc diffusion method and polymerase chain reaction respectively. Moreover, ERIC-PCR typing was performed to investigate the genetic diversity among the clinical isolates. No significant correlation was observed between biofilm formation and resistance to each antimicrobial agent. Similar observation was detected concerning the multidrug resistance and biofilm formation. Regarding virulence genes, algD gene was harbored by all isolates (100%). Only pelA and phzM were significantly prevalent in strong biofilm producers. Additionally, the mean virulence score was higher in strong biofilm producers (9.33) than moderate (8.62) and weak (7) biofilm producers. Moreover, there was a significant correlation between the overall virulence score of the isolates and its ability to form biofilm. ERIC-PCR genotyping revealed the presence of 99 different ERIC patterns based on 70% similarity, and the different ERIC patterns were categorized into 8 clusters. 100% similarity indicates the possibility of cross-colonization in P. aeruginosa infections.

Tailoring spatial structure of electroactive biofilm for enhanced activity and direct electron transfer on iron phthalocyanine modified anode in microbial fuel cells

Electroactive biofilm (EAB) has been considered as the core determining electricity generation in microbial fuel cells (MFCs), and its spatial structure regulation for enhanced activity and selectivity is of great concern. In this study, iron phthalocyanine (FePc) was introduced into a carbon cloth (CC) electrode, aiming at improving the affinity between the anode and outer membrane c-type cytochromes (OM c-Cyts) and achieving a highly active EAB. The FePc modified CC anode (FePc-CC) effectively improved the viability of EAB and enriched the Geobacter species up to 44.83% (FePc-CC) from 6.97% (CC). The FePc-CC anode achieved a much higher power density of 2419 mW m^-2 than the CC (560 mW m^-2) and a remarkable higher biomass loading of 2477.2 ± 84.5 μg cm^-2 than the CC (749.3 ± 31.3 μg cm^-2). As the charge transfer resistance was decreased by 58.6 times from 395.2 Ω (CC) to 6.74 Ω (FePc-CC), the interfacial reaction rate was accelerated and the direct electron transfer via OM c-Cyts was promoted. This work provides an effective method to improve the EAB activity by regulating its spatial structure, and opens the door toward the development of highly active EAB using metal phthalocyanines in MFCs.

Carbon supports on preparing iron-nitrogen dual-doped carbon (Fe-N/C) electrocatalysts for microbial fuel cells: mini-review

Microbial fuel cells (MFCs) are devices that treat sewage and generate electricity. Recent researches have demonstrated that the characteristics of carbon precursors can tremendously influence the performance of the MFC cathode. Carbon nanomaterials with good crystallinity as well as high specific surface area (e.x., graphene and carbon nanotube) can not only accelerate charge transport but also afford a good dispersion of catalytic active components, leading to high MFC performance. On these bases, the preparation of highly-active Fe-N/C catalysts using different carbon substrates are mainly discussed in this review. It is pointed out that increasing the surface area and conductivity as well as elevating the density of active sites to reduce the oxygen reduction overpotential is still the emphasis of the current works. At present, although the researchers have made some progress, the output power density is far from meeting the actual application needs.

Synergistic effects in a microbial fuel cell between co-cultures and a photosynthetic alga Chlorella vulgaris improve performance

Microbial communities are catalysts that drive the operation of microbial fuel cells (MFCs). In this study, the use of a defined co-culture of Escherichia coli and Pseudomonas aeruginosa towards improved power generation in MFCs is described. The co-culture has been initially evaluated for substrate consumption, biofilm formation and microbial electron transfer activity. The co-culture gave an enhanced power density of 190.44 mW m⁻², while E. coli and P. aeruginosa as pure cultures generated lesser power densities of 139.24 and 158.76 mW m⁻² respectively. The photosynthetic alga Chlorella vulgaris was then inoculated in the cathode chamber. Co-cultures in the presence of C. vulgaris improved the mean power density from 175 mW m⁻² to 248 mW m⁻², a 41.7% rise. A synergistic effect was observed when the co-cultures were coupled with C. vulgaris. Combining co-cultures with photosynthetic MFCs offers a lot of promise in studying mechanisms and expanding the nature of applications.

Bacterial community structure and gene function prediction in response to long-term running of dual graphene modified bioelectrode bioelectrochemical systems

This work studied bacterial community structure and gene function prediction in long-term running of dual graphene modified bioelectrode bioelectrochemical systems (LT D-GM-BE BES, 2 year). The maximum power density of LT D-GM-BE BES was 99.03 ± 3.64 mW/m², which was 3.66 times of dual control BES (D-C-BE BES), and the transfer resistance of LT GM-BE was just approximately 1/4 of control bioelectrode (C-BE). Proteobacteria and Firmicutes were dominant bacteria in long-term modified bioanode (LT GM-BA, 30.03% and 45.64%), and in long-term modified biocathode (LT GM-BC) was Armatimonadetes (47.14%) in phylum level. The dominant bacteria in LT GM-BA was Clostridium (30.56%), in GM-BC was Chthonomonas (47.14%) in genus level. Gene function related with substrate, energy metabolism and environmental adaptation were enriched. LT GM-BE was tended to enrich dominant bacteria and enrich gene to adapt to micro-environmental changes. This study would provide metagenomics information for long-term running of BES in future.

A 96-well high-throughput, rapid-screening platform of extracellular electron transfer in microbial fuel cells

Microbial extracellular electron transfer (EET) stimulates a plethora of intellectual concepts leading to potential applications that offer environmentally sustainable advances in the fields of biofuels, wastewater treatment, bioremediation, desalination, and biosensing. Despite its vast potential and remarkable research efforts to date, bacterial electrogenicity is arguably the most underdeveloped technology used to confront the aforementioned challenges. Severe limitations are placed in the intrinsic energy and electron transfer processes of naturally occurring microorganisms. Significant boosts in this technology can be achieved with the growth of synthetic biology tools that manipulate microbial electron transfer pathways and improve their electrogenic potential. In particular, electrogenic Pseudomonas aeruginosa has been studied with the utility of its complete genome being sequenced coupled with well-established techniques for genetic manipulation. To optimize power density production, a high-throughput, rapid and highly sensitive test array for measuring the electrogenicity of hundreds of genetically engineered P. aeruginosa mutants is needed. This task is not trivial, as the accurate and parallel quantitative measurements of bacterial electrogenicity require long measurement times (~tens of days), continuous introduction of organic fuels (~tends of milliliters), architecturally complex and often inefficient devices, and labor-intensive operation. The overall objective of this work was to enable rapid (<30 min), sensitive (>100-fold improvement), and high-throughput (>96 wells) characterization of bacterial electrogenicity from a single 5 μL culture suspension. This project used paper as a substratum that inherently produces favorable conditions for easy, rapid, and sensitive control of an electrogenic microbial suspension. From 95 isogenic P. aeruginosa mutant, an hmgA mutant generated the highest power density (39 μW/cm²), which is higher than that of wild-type P. aeruginosa and even the strongly electrogenic organism, Shewanella oneidensis (25 μW/cm²). In summary, this work will serve as a springboard for the development of novel paradigms for genetic networks that will help develop mutations or over-expression and synthetic biology constructs to identify genes in P. aeruginosa and other organisms that enhance electrogenic performance in microbial fuel cells (MFCs).

Bioelectrochemical remediation of phenanthrene in a microbial fuel cell using an anaerobic consortium enriched from a hydrocarbon-contaminated site

Polycyclic aromatic hydrocarbons (PAH) are organic pollutants that require remediation due to their detrimental impact on human and environmental health. In this study, we used a novel approach of sequestering a model PAH, phenanthrene, onto a solid carbon matrix bioanode in a microbial fuel cell (MFC) to assess its biodegradation coupled with power generation. Here, the bioanode serves as a site for enrichment of electroactive and hydrocarbon-degrading microorganisms, which can simultaneously act to biodegrade a pollutant and generate power. Carbon cloth electrodes loaded with two rates of phenanthrene (2 and 20 mg cm^-2) were compared using dual chamber MFCs that were operated for 50 days. The lower loading rate of 2 mg cm^-2 was most efficient in the degradation of phenanthrene and had higher power production capacities (37 mW m^-2) as compared to the higher loading rate of 20 mg cm^-2 (power production of 19.2 mW m^-2). FTIR (Fourier-Transform Infrared Spectroscopy) analyses showed a depletion in absorbance peak signals associated with phenanthrene. Microbes known to have electroactive properties or phenanthrene biodegradation abilities like Pseudomonas, Rhodococcus, Thauera and Ralstonia were enriched over time in the MFCs, substantiating the electrochemical and FTIR analyses. The MFC approach taken here thus offers great promise towards PAH bioelectroremediation.

Anoxic-biocathode microbial desalination cell as a new approach for wastewater remediation and clean water production

Bioelectrochemical systems are emerging as a promising and friendly alternative to convert the energy stored in wastewater directly into electricity by microorganisms and utilize it in situ to drive desalination. To better understand such processes, we propose the development of an anoxic biocathode microbial desalination Cell for the conversion of carbon- and nitrogen-rich wastewaters into bioenergy and to perform salt removal. Our results demonstrate a power output of 0.425 W m^-3 with desalination, organic matter removal and nitrate conversion efficiencies of 43.69, 99.85 and 92.11% respectively. Microbiological analysis revealed Proteobacteria as the dominant phylum in the anode (88.45%) and biocathode (97.13%). While a relatively higher bacterial abundance was developed in the anode chamber, the biocathode showed a greater variety of microorganisms, with a predominance of Paracoccus (73.2%), which are related to the denitrification process. These findings are promising and provide new opportunities for the development and application of this technology in the field of wastewater treatment to produce cleaner water and conserve natural resources.

A journey in the complex interactions between electrochemistry and bacteriology: From electroactivity to electromodulation of bacterial biofilms

Although the term bioelectrochemistry tends to be associated with animal and human tissues, bioelectric currents exist also in plants and bacteria. Especially the latter, when agglomerated in the form of biofilms, can exhibit electroactivity and susceptibility to electrical stimulation. Therefore, electrochemical methods appear to become powerful techniques to expand the conventional strategies of biofilm characterization and modification. In this review, we aim to provide the insight into the electrochemical behaviour of bacteria and present the variety of electrochemical techniques that can be used either for the non-destructive monitoring of bacterial communities or modulation of their growth. The most common applications of electrical stimulation on biofilms are presented, including the prevention of bacterial growth by charging the surface of the materials, changing the direction of bacterial movement under the influence of the electric field and increasing of the potency of antibiotics when bactericides are coupled with the electric field. Also, the industrial applications of microbial electro-technologies are described, such as bioremediation, wastewater treatment, and microbial fuel cells. Consequently, we are showing the complexity of interactions that exist between electrochemistry and bacteriology that can be used for the benefit of these two disciplines.

Synergic degradation of 2,4,6-trichlorophenol in microbial fuel cells with intimately coupled photocatalytic-electrogenic anode

A microbial fuel cell system with intimately coupled photocatalytic-electrogenic anode (photocatalytic-MFC) was proposed for the synergetic degradation of 2,4,6-trichlorophenol (2,4,6-TCP) which has a structure of three chlorine groups connecting to a phenol ring and is well recognized as a recalcitrant pollutant for its high toxicity, bioaccumulation and persistence. The photocatalytic-electrogenic anode was prepared by coating mpg-C₃N₄ on a carbon felt anode, followed by inoculating with municipal sewage and acclimating with 2,4,6-TCP at gradient concentrations. Improved TCP degradation was achieved, showing 79.3% of TCP removal in 10 h with an original concentration of 200 mg L^-1, which was higher than that obtained with the unilluminated MFC (66.0%) and the photocatalytic-only process (56.1%). The coupled photocatalytic-electrogenic process demonstrated different degradation pathways compared with the photocatalytic-only process, with one open-chain compound (2-chloro-4-keto-2-hexenedioic acid, 2-CMA) detected in the photocatalytic-MFC system. Microbial community analysis revealed that Pseudomonas, instead of Geobacter observed in the unilluminated MFC bioanode, dominated in the photocatalytic-electrogenic anode MFC biofilm, which might be responsible for enhanced current generation in the coupled system. In addition, biofilm rich with Rhodococcus on air-cathode was also responsible for the enhanced TCP removal. This research provides an efficient strategy for the treatment of wastewater with recalcitrant contaminants by intimate-coupling of the photocatalytic and the electrogenic processes.

Biofouling of membranes in microbial electrochemical technologies: Causes, characterization methods and mitigation strategies

The scope of the review is to discuss the current state of knowledge and lessons learned on biofouling of membrane separators being used for microbial electrochemical technologies (MET). It is illustrated what crucial membrane features have to be considered and how these affect the MET performance, paying particular attention to membrane biofouling. The complexity of the phenomena was demonstrated and thereby, it is shown that membrane qualities related to its surface and inherent material features significantly influence (and can be influenced by) the biofouling process. Applicable methods for assessment of membrane biofouling are highlighted, followed by the detailed literature evaluation. Finally, an outlook on e.g. possible mitigation strategies for membrane biofouling in MET is provided.

Prospects in bioelectrochemical technologies for wastewater treatment

Bioelectrochemical technologies are emerging as innovative solutions for waste treatment, offering flexible platforms for both oxidation and reduction reaction processes. A great variety of applications have been developed by utilizing the energy produced in bioelectrochemical systems, such as direct electric power generation, chemical production or water desalination. This manuscript provides a literature review on the prospects in bioelectrochemical technologies for wastewater treatment, including organic, nutrients and metals removal, production of chemical compounds and desalination. The challenges and perspectives for scale-up were discussed. A technological strategy to improve the process monitoring and control based on big data platforms is also presented. To translate the viability of wastewater treatment based on bioelectrochemical technologies into commercial application, it is necessary to exploit interdisciplinary areas by combining the water/wastewater sector, energy and data analytics technologies.

Electro-Microbiology as a Promising Approach Towards Renewable Energy and Environmental Sustainability

Microbial electrochemical technologies provide sustainable wastewater treatment and energy production. Despite significant improvements in the power output of microbial fuel cells (MFCs), this technology is still far from practical applications. Extracting electrical energy and harvesting valuable products by electroactive bacteria (EAB) in bioelectrochemical systems (BESs) has emerged as an innovative approach to address energy and environmental challenges. Thus, maximizing power output and resource recovery is highly desirable for sustainable systems. Insights into the electrode-microbe interactions may help to optimize the performance of BESs for envisioned applications, and further validation by bioelectrochemical techniques is a prerequisite to completely understand the electro-microbiology. This review summarizes various extracellular electron transfer mechanisms involved in BESs. The significant role of characterization techniques in the advancement of the electro-microbiology field is discussed. Finally, diverse applications of BESs, such as resource recovery, and contributions to the pursuit of a more sustainable society are also highlighted.

Weak electricigens: A new avenue for bioelectrochemical research

Electroactivity appears to be a phylogenetically diverse trait independent of cell wall classification, with both Gram-negative and Gram-positive electricigens reported. While numerous electricigens have been observed, the majority of research focuses on a select group of highly electroactive species. Under favorable conditions, many microorganisms can be considered electroactive, either through their own mechanisms or exogenously-added mediators, producing a weak current. Such microbes should not be dismissed based on their modest electroactivity. Rather, they may be key to understanding what drives extracellular electron transfer in response to transient limitations of electron acceptor or donor, with implications for the study of pathogens and industrial bioprocesses. Due to their low electroactivity, such populations are difficult to grow in bioelectrochemical systems and characterise with electrochemistry. Here, a critical review of recent research on weak electricigens is provided, with a focus on the methodology and the overall relevance to microbial ecology and bioelectrochemical systems.

Hierarchically Porous N-Doped Carbon Nanotubes/Reduced Graphene Oxide Composite for Promoting Flavin-Based Interfacial Electron Transfer in Microbial Fuel Cells

Interfacial electron transfer between an electroactive biofilm and an electrode is a crucial step for microbial fuel cells (MFCs) and other bio-electrochemical systems. Here, a hierarchically porous nitrogen-doped carbon nanotubes (CNTs)/reduced graphene oxide (rGO) composite with polyaniline as the nitrogen source has been developed for the MFC anode. This composite possesses a nitrogen atom-doped surface for improved flavin redox reaction and a three-dimensional hierarchically porous structure for rich bacterial biofilm growth. The maximum power density achieved with the N-CNTs/rGO anode in S. putrefaciens CN32 MFCs is 1137 mW m^-2, which is 8.9 times compared with that of the carbon cloth anode and also higher than those of N-CNTs (731.17 mW m^-2), N-rGO (442.26 mW m^-2), and the CNTs/rGO (779.9 mW m^-2) composite without nitrogen doping. The greatly improved bio-electrocatalysis could be attributed to the enhanced adsorption of flavins on the N-doped surface and the high density of biofilm adhesion for fast interfacial electron transfer. This work reveals a synergistic effect from pore structure tailoring and surface chemistry designing to boost both the bio- and electrocatalysis in MFCs, which also provide insights for the bioelectrode design in other bio-electrochemical systems.

Effect of impaired twitching motility and biofilm dispersion on performance of Pseudomonas aeruginosa-powered microbial fuel cells

Pseudomonas aeruginosa is a metabolically voracious bacterium that is easily manipulated genetically. We have previously shown that the organism is also highly electrogenic in microbial fuel cells (MFCs). Polarization studies were performed in MFCs with wild-type strain PAO1 and three mutant strains (pilT, bdlA and pilT bdlA). The pilT mutant was hyperpiliated, while the bdlA mutant was suppressed in biofilm dispersion chemotaxis. The double pilT bdlA mutant was expected to have properties of both mutations. Polarization data indicate that the pilT mutant showed 5.0- and 3.2-fold increases in peak power compared to the wild type and the pilT bdlA mutant, respectively. The performance of the bdlA mutant was surprisingly the lowest, while the pilT bdlA electrogenic performance fell between the pilT mutant and wild-type bacteria. Measurements of biofilm thickness and bacterial viability showed equal viability among the different strains. The thickness of the bdlA mutant, however, was twice that of wild-type strain PAO1. This observation implicates the presence of dead or dormant bacteria in the bdlA mutant MFCs, which increases biofilm internal resistance as confirmed by electrochemical measurements.