Decoupling the effects of nanopore size and surface roughness on the attachment, spreading and differentiation of bone marrow-derived stem cells

Evaluation of tribological and biological properties of Ti6Al4V coated with Si3N4/ND nanoparticles for orthopedic applications: a comprehensive analysis

In this study, the biocompatibility and tribological properties of Ti6Al4V coated with silicon nitride (Si3N4)/nanodiamond using the electrophoretic deposition method were investigated. Suspensions of various aqueous and alcoholic solutions were prepared in the presence of CTAB and SDS dispersers. The most stable suspension system for the electrophoresis process was selected (aqueous media/ SDS disperser). Four different voltages (20, 30, 40 and 50 V) were applied to study the effect of voltage on the coating property. One could find that processing with 40 V obtained the best coating. The nano-composite coating was characterized using scanning electron microscopy equipped with energy dispersive spectroscopy, mapping analysis and x-ray diffraction after the coating process. The samples were then subjected to two nanoindentation and nano-scratching tests to evaluate their tribological properties. Biocompatibility was assessed in an ex vivo environment using two cell culture tests to evaluate survival and cellular adhesion. The results showed that the hardness and modulus elasticity of the coated sample increased from 85 to 124 GPa and 1.14-3.55 GPa, respectively, compared to the non-coated sample. Additionally, the MTT test results indicated that cellular survival and proliferation of MG63 cells increased from 86% for the non-coated sample to 92% for the Ti6Al4V/Si3N4/ND sample. These findings have implications for orthopedic implant applications.

Engineering Biodegradable Polyurethanes with Precisely Controlled Hierarchical Structures to Access Shape Memory Effect and Enhanced Bioactivities

Biodegradable polymers with shape memory effects (SMEs) offer promising solutions for short-term medical interventions, facilitating minimally invasive procedures and subsequent degradation without requiring secondary surgeries. However, achieving a good balance among desirable SMEs, mechanical performance, degradation rate, and bioactivities remains a significant challenge. To address this issue, we established a strategy to develop a versatile biodegradable polyurethane (PPDO-PLC) with tunable hierarchical structures via precise chain segment control. Initial copolymerization of l-lactide and ε-caprolactone sets a tunable Tg close to body temperature, followed by block copolymerization with poly(p-dioxanone) to form a hard domain. This yields a uniform microphase-separation morphology, ensuring robust SME and facilitating the development of roughly porous surface structures in alkaline environments. Cell experiments indicate that these rough surfaces significantly enhance cellular activities, such as adhesion, proliferation, and osteogenic differentiation. Our approach provides a methodology for balancing biodegradability, SMEs, three-dimensional (3D) printability, and bioactivity in materials through hierarchical structure regulation.

Construction of antibacterial bone implants and their application in bone regeneration

Bacterial infection represents a prevalent challenge during the bone repair process, often resulting in implant failure. However, the extensive use of antibiotics has limited local antibacterial effects at the infection site and is prone to side effects. In order to address the issue of bacterial infection during the transplantation of bone implants, four types of bone scaffold implants with long-term antimicrobial functionality have been constructed, including direct contact antimicrobial scaffold, dissolution-penetration antimicrobial scaffold, photocatalytic antimicrobial scaffold, and multimodal synergistic antimicrobial scaffold. The direct contact antimicrobial scaffold involves the physical penetration or disruption of bacterial cell membranes by the scaffold surface or hindrance of bacterial adhesion through surface charge, microstructure, and other factors. The dissolution-penetration antimicrobial scaffold releases antimicrobial substances from the scaffold's interior through degradation and other means to achieve local antimicrobial effects. The photocatalytic antimicrobial scaffold utilizes the absorption of light to generate reactive oxygen species (ROS) with enhanced chemical reactivity for antimicrobial activity. ROS can cause damage to bacterial cell membranes, deoxyribonucleic acid (DNA), proteins, and other components. The multimodal synergistic antimicrobial scaffold involves the combined use of multiple antimicrobial methods to achieve synergistic effects and effectively overcome the limitations of individual antimicrobial approaches. Additionally, the biocompatibility issues of the antimicrobial bone scaffold are also discussed, including in vitro cell adhesion, proliferation, and osteogenic differentiation, as well as in vivo bone repair and vascularization. Finally, the challenges and prospects of antimicrobial bone implants are summarized. The development of antimicrobial bone implants can provide effective solutions to bacterial infection issues in bone defect repair in the foreseeable future.

Efficient three-dimensional (3D) human bone differentiation on quercetin-functionalized isotropic nano-architecture chitinous patterns of cockroach wings

Developing cost-effective, biocompatible scaffolds with nano-structured surface that truthfully replicate the physico-(bio)chemical and structural properties of bone tissue's extracellular matrix (ECM) is still challenging. In this regard, surface functionalization of natural scaffolds to enhance capability of mimicking 3D niches of the bone tissue has been suggested as a solution. In the current study, we aimed to investigate the potential of chitin-based cockroach wings (CW) as a natural scaffold for bone tissue engineering. To raise the osteogenic differentiation capacity of such a scaffold, a quercetin coating was also applied (hereafter this scaffold is referred as QCW). Moreover, the QCW scaffold exhibited effective antibacterial properties against gram-positive S. aureus bacteria. With respect to bone regeneration, the QCW scaffold optimally induced the differentiation of adipose-derived human mesenchymal stem cells (AD-hMSCs) into osteoblasts, as validated by mineralization assays, alkaline phosphatase (ALP) activity measurements, expression of pre-osteocyte marker genes, and immunocytochemical staining. Confirmation of the potent biocompatibility and physicochemical characteristics of the QCW scaffold through a series of in vitro and in vivo analysis revealed that surface modification had significant effect on multi-purpose features of obtained scaffold. Altogether, surface modification of QCW made it as an affordable bioinspired scaffold for bone tissue engineering.

Biomaterials regulates BMSCs differentiation via mechanical microenvironment

Bone mesenchymal stem cells (BMSCs) are crucial for bone tissue regeneration, the mechanical microenvironment of hard tissues, including bone and teeth, significantly affects the osteogenic differentiation of BMSCs. Biomaterials may mimic the microenvironment of the extracellular matrix and provide mechanical signals to regulate BMSCs differentiation via inducing the secretion of various intracellular factors. Biomaterials direct the differentiation of BMSCs via mechanical signals, including tension, compression, shear, hydrostatic pressure, stiffness, elasticity, and viscoelasticity, which can be transmitted to cells through mechanical signalling pathways. Besides, biomaterials with piezoelectric effects regulate BMSCs differentiation via indirect mechanical signals, such as, electronic signals, which are transformed from mechanical stimuli by piezoelectric biomaterials. Mechanical stimulation facilitates achieving vectored stem cell fate regulation, while understanding the underlying mechanisms remains challenging. Herein, this review summarizes the intracellular factors, including translation factors, epigenetic modifications, and miRNA level, as well as the extracellular factor, including direct and indirect mechanical signals, which regulate the osteogenic differentiation of BMSCs. Besides, this review will also give a comprehensive summary about how mechanical stimuli regulate cellular behaviours, as well as how biomaterials promote the osteogenic differentiation of BMSCs via mechanical microenvironments. The cellular behaviours and activated signal pathways will give more implications for the design of biomaterials with superior properties for bone tissue engineering. Moreover, it will also provide inspiration for the construction of bone organoids which is a useful tool for mimicking in vivo bone tissue microenvironments.

Morphology of Nanostructured Tantalum Oxide Controls Stem Cell Differentiation and Improves Corrosion Behavior

Tantalum is receiving increasing attention in the biomedical field due to its biocompatible nature and superior mechanical properties. However, the bioinert nature of tantalum still poses a challenge and limits its integration into the bone tissue. To address these issues, we fabricated nanotubular (NT), nanocoral (NC), and nanodimple morphologies on tantalum surfaces via anodization. The size of these nanofeatures was engineered to be approximately 30 nm for all anodized samples. Thus, the influence of the anodized nanostructured morphology on the chemical and biological properties of tantalum was evaluated. The NT and NC samples exhibited higher surface roughness, surface energy, and hydrophilicity compared to the nonanodized samples. In addition, the NT samples exhibited the highest corrosion resistance among all of the investigated samples. Biological experiments indicated that NT and NC samples promoted human adipose tissue-derived mesenchymal stem cell (hADMSC) spreading and proliferation up to 5 days in vitro. ALP, COL1A1, and OSC gene expressions as well as calcium mineral synthesis were upregulated on the NT and NC samples in the second and third weeks in vitro. These findings highlight the significance of nanostructured feature morphology for anodized tantalum, where the NT morphology was shown to be a potential candidate for orthopedic applications.

Induced Formation of Plasma Membrane Protrusions with Porous Materials as Instructive Surfaces

The plasma membrane is a vital component in cellular processes, and its structure has a significant impact on cellular behavior. The physical characteristics of the extracellular environment, along with the presence of surface pores, can influence the formation of membrane protrusions. Nanoporous surfaces have demonstrated their capacity to induce membrane protrusions in both adherent and non-adherent cells. This chapter presents a methodology that utilizes a nanoporous substrate with nanotopographical constraints to effectively stimulate the formation of membrane protrusions in cells.

Unusual effects of a nanoporous gold substrate on cell adhesion and differentiation because of independent multi-branch signaling of focal adhesions

A variety of cell behaviors, such as cell adhesion, motility, and fate, can be controlled by substrate characteristics such as surface topology and chemistry. In particular, the surface topology of substrates strongly affects cell behaviors, and the topological spacing is a critical factor in inducing cell responses. Various works have demonstrated that cell adhesion was enhanced with decreasing topological spacing although differentiation progressed slowly. However, there are exceptions, and thus, correlations between topological spacing and cell responses are still debated. We show that a nanoporous gold substrate affected cell adhesion while it neither affected osteogenic nor adipogenic differentiation. In addition, the cell adhesion was reduced with decreasing pore size. These do not agree with previous findings. A focal adhesion (FA) is an aggregate of modules comprising specific proteins such as FA kinase, talin, and vinculin. Therefore, it is suggested that because various extracellular signals can be independently branched off from the FA modules, the unusual effects of nanoporous gold substrates are related to the multi-branching of FAs.

Atomic Layer Deposition of Tantalum Oxide Films on 3D-Printed Ti6Al4V Scaffolds with Enhanced Osteogenic Property for Orthopedic Implants

There is an evident advantage in personalized customization of orthopedic implants by 3D-printed titanium (Ti) and its alloys. However, 3D-printed Ti alloys have a rough surface structure caused by adhesion powders and a relatively bioinert surface. Therefore, surface modification techniques are needed to improve the biocompatibility of 3D-printed Ti alloy implants. In the present study, porous Ti6Al4V scaffolds were manufactured by a selective laser melting 3D printer, followed by sandblasting and acid-etching treatment and atomic layer deposition (ALD) of tantalum oxide films. SEM morphology and surface roughness tests confirmed that the unmelted powders adhered on the scaffolds were removed by sandblasting and acid-etching. Accordingly, the porosity of the scaffold increased by about 7%. Benefiting from the self-limitation and three-dimensional conformance of ALD, uniform tantalum oxide films were formed on the inner and outer surfaces of the scaffolds. Zeta potential decreased by 19.5 mV after depositing tantalum oxide films. The in vitro results showed that the adhesion, proliferation, and osteogenic differentiation of rat bone marrow mesenchymal stem cells on modified Ti6Al4V scaffolds were significantly enhanced, which may be ascribed to surface structure optimization and the compatibility of tantalum oxide. This study provides a strategy to improve the cytocompatibility and osteogenic differentiation of porous Ti6Al4V scaffolds for orthopedic implants.

Engineering Female Germline Stem Cells with Exocytotic Polymer Dots

Germline stem cells (GSCs) are the only cell population capable of passing genetic information to offspring, making them attractive targets in reproductive biology and fertility research. However, it is generally more difficult to introduce exogenous biomolecules into GSCs than other cell types, impeding the exploration and manipulation of these cells for biomedical purposes. Herein, semiconductor polymer dots (Pdots)-based nanocomplex Pdot-siRNA is developed and achieves effective knockdown of target genes in female germline stem cells (FGSCs). Advantage of high fluorescence brightness of Pdots is taken for comprehensive investigation of their cellular uptake, intracellular trafficking, and exocytosis in FGSCs. Importantly, Pdots show excellent biocompatibility and minimally disturb the differentiation of FGSCs. Intracellular Pdots escape from the lysosomes and undergo active exocytosis, which makes them ideal nanocarriers for bioactive cargos. Moreover, Pdot-siRNA can penetrate into 3D ovarian organoids derived from FGSCs and down-regulate the expression levels of target genes. This study investigates the interface between a type of theranostic nanoparticles and FGSCs for the first time and sheds light on the manipulation and medical application of FGSCs.

Stimulating factors for regulation of osteogenic and chondrogenic differentiation of mesenchymal stem cells

Mesenchymal stem cells (MSCs), distributed in many tissues in the human body, are multipotent cells capable of differentiating in specific directions. It is usually considered that the differentiation process of MSCs depends on specialized external stimulating factors, including cell signaling pathways, cytokines, and other physical stimuli. Recent findings have revealed other underrated roles in the differentiation process of MSCs, such as material morphology and exosomes. Although relevant achievements have substantially advanced the applicability of MSCs, some of these regulatory mechanisms still need to be better understood. Moreover, limitations such as long-term survival in vivo hinder the clinical application of MSCs therapy. This review article summarizes current knowledge regarding the differentiation patterns of MSCs under specific stimulating factors.

Study on the influence of scaffold morphology and structure on osteogenic performance

The number of patients with bone defects caused by various bone diseases is increasing yearly in the aging population, and people are paying increasing attention to bone tissue engineering research. Currently, the application of bone tissue engineering mainly focuses on promoting fracture healing by carrying cytokines. However, cytokines implanted into the body easily cause an immune response, and the cost is high; therefore, the clinical treatment effect is not outstanding. In recent years, some scholars have proposed the concept of tissue-induced biomaterials that can induce bone regeneration through a scaffold structure without adding cytokines. By optimizing the scaffold structure, the performance of tissue-engineered bone scaffolds is improved and the osteogenesis effect is promoted, which provides ideas for the design and improvement of tissue-engineered bones in the future. In this study, the current understanding of the bone tissue structure is summarized through the discussion of current bone tissue engineering, and the current research on micro-nano bionic structure scaffolds and their osteogenesis mechanism is analyzed and discussed.

Plant-Derived Polyphenol and LL-37 Peptide-Modified Nanofibrous Scaffolds for Promotion of Antibacterial Activity, Anti-Inflammation, and Type-H Vascularized Bone Regeneration

The regeneration of oral tissues is a challenging clinical problem because of the complex microbial and biological stress environments. Electrospun fibrous scaffolds have attracted significant interest as effective barrier membranes for guided bone regeneration (GBR); however, no mature strategy yet exists for the surface modification of fibers to provide versatility to satisfy clinical requirements. This study demonstrated a practical biosafety strategy: the combined use of plant polyphenols and LL-37 peptides to modify the fiber surface to endow the fibrous scaffold with antimicrobial activity, immunoregulation, and vascularized bone regeneration. We confirmed that the LL-37 peptides interacted with tannic acid (TA) through noncovalent bonds through experiments and molecular docking simulation analysis. In vitro experiments showed that the TA coating imparted strong antibacterial properties to the fibrous scaffold, but it also caused cytotoxicity. The grafting of LL-37 peptide promoted the spreading, migration, and osteogenic differentiation of mesenchymal stem cells and was also conducive to the M2 polarization of RAW264.7 cells. In vivo experiments further verified that the LL-37 peptide-grafted fibrous scaffold significantly enhanced angiogenesis, anti-inflammatory effects, and type-H vascularized bone regeneration. Overall, the fibrous scaffold modified by the LL-37 peptide through TA grafting has significant potential for GBR applications.

Effects of Allogeneic Bone Substitute Configurations on Cell Adhesion Process In Vitro

OBJECTIVE

To explore the potential effect of three allogenic bone substitute configurations on the viability, adhesion, and spreading of osteoblasts in vitro.

METHODS

Freeze-dried cortical bone were ground and fractions were divided into three groups with different sizes and shapes, defined as bone fiber (0.1 mm × 0.1 mm × 3 mm), bone powder (0.45-0.9 mm), and bone granule group (3-6 mm). MC3T3-E1 cells were divided and co-cultured within groups to induce cell adhesion. The configuration of allogenic bone was captured by scanning electron microscopy and confocal laser scanning microscopy, and substrate roughness values were quantified. Cell adhesion rate was assessed using the hemocyte counting method, cell viability was determined by CCK-8 assay and live/dead staining, and cell morphology was visualized by Phalloidin and DAPI, and the mRNA expression of adhesion-related gene (vinculin) of different substitutes were determined with quantitative real-time polymerase chain reaction.

RESULTS

The roughness values of bone fiber, bone powder, and bone granule group were 1.878 μm (1.578-2.415 μm), 5.066 μm (3.891-6.162 μm), and 0.860 μm (0.801-1.452 μm), respectively (bone powder group compared with bone granule group, H = 18.015, P < 0.001). Similar OD values of all groups in CCK-8 assay indicated good biocompatibility of these substitutes (bone fiber, 0.201 ± 0.004; bone powder, 0.206 ± 0.008; bone granule group, 0.197 ± 0.006; and the control group, 0.202 ± 0.016, F = 0.7152, P > 0.05). In addition, representative cell adhesion rates at 24 h showed significantly lower cell adhesion rate in bone fiber group (20.3 ± 1.6%) compared to bone powder (29.3 ± 4.4%) and bone granule group (27.3 ± 3.2%) (F = 10.51，P = 0.009 and P = 0.034, respectively), but there was no significant difference between the latter two groups (P > 0.05). Interestingly, the expression of vinculin mRNA steadily decreased in a time-dependent manner. The vinculin expression reached its peak at 6 h in each group, and the vinculin levels in bone fiber, bone powder, and bone granule group were 2.119 ± 0.052, 3.842 ± 0.108, and 3.585 ± 0.068 times higher than those in the control group, respectively (F = 733.643, all P < 0.001). Meanwhile, there was a significant difference in the expression of target gene between bone powder and bone granule group (P = 0.006).

CONCLUSION

All allogenic bone substitutes presented an excellent cell viability. Moreover, bone powder and bone granule group were more likely to promote cell adhesion and spreading compared to bone fiber group.

Osteogenic and anti-inflammatory effect of the multifunctional bionic hydrogel scaffold loaded with aspirin and nano-hydroxyapatite

Although tissue engineering offered new approaches to repair bone defects, it remains a great challenge to create a bone-friendly microenvironment and rebuild bone tissue rapidly by a scaffold with a bionic structure. In this study, a multifunctional structurally optimized hydrogel scaffold was designed by integrating polyvinyl alcohol (PVA), gelatin (Gel), and sodium alginate (SA) with aspirin (ASA) and nano-hydroxyapatite (nHAP). The fabrication procedure is through a dual-crosslinking process. The chemical constitution, crystal structure, microstructure, porosity, mechanical strength, swelling and degradation property, and drug-release behavior of the hydrogel scaffold were analyzed. Multi-hydrogen bonds, electrostatic interactions, and strong "egg-shell" structure contributed to the multi-network microstructure, bone tissue-matched properties, and desirable drug-release function of the hydrogel scaffold. The excellent performance in improving cell viability, promoting cell osteogenic differentiation, and regulating the inflammatory microenvironment of the prepared hydrogel scaffold was verified using mouse pre-osteoblasts (MC3T3-E1) cells. And the synergistic osteogenic and anti-inflammatory functions of aspirin and nano-hydroxyapatite were also verified. This study provided valuable insights into the design, fabrication, and biological potential of multifunctional bone tissue engineering materials with the premise of constructing a bone-friendly microenvironment.

Construction of Vascularized Tissue Engineered Bone with nHA-Coated BCP Bioceramics Loaded with Peripheral Blood-Derived MSC and EPC to Repair Large Segmental Femoral Bone Defect

The regenerative repair of segmental bone defect (SBD) is an urgent problem in the field of orthopedics. Rapid induction of angiogenesis and osteoinductivity after implantation of scaffold is critical. In this study, a unique tissue engineering strategy with mixture of peripheral blood-derived mesenchymal stem cells (PBMSC) and endothelial progenitor cells (PBEPC) was applied in a 3D-printed biphasic calcium phosphate (BCP) scaffold with highly bioactive nano hydroxyapatite (nHA) coating (nHA/BCP) to construct a novel vascularized tissue engineered bone (VTEB) for rabbit femoral SBD repair. The 2D coculture of PBMSC and PBEPC showed that they could promote the osteogenic or angiogenic differentiation of the cells from each other, especially in the group of PBEPC/PBMSC = 75:25. Besides, the 3D coculture results exhibited that the nHA coating could further promote PBEPC/PBMSC adhesion, proliferation, and osteogenic and angiogenic differentiation on the BCP scaffold. In vivo experiments showed that among the four groups (BCP, BCP-PBEPC/PBMSC, nHA/BCP, and nHA/BCP-PBEPC/PBMSC), the nHA/BCP-PBEPC/PBMSC group induced the best formation of blood vessels and new bone and, thus, the good repair of SBD. It revealed the synergistic effect of nHA and PBEPC/PBMSC on the angiogenesis and osteogenesis of the BCP scaffold. Therefore, the construction of VTEB in this study could provide a possibility for the regenerative repair of SBD.

Analysis of disordered abrasive scratches on titanium surfaces and their impact on nuclear translocation of yes-associated protein

The morphology of the metallic surface of an implant is important for its contact with bone tissue as it directly affects osteoblast functions, such as cell adhesion, proliferation, and differentiation. Firm contact between the implant and cells creates a barrier that prevents inflammation and bacterial infections. Therefore, optimizing surface morphology, such as surface roughness adjustments, is essential to improving the adhesion between the implant and cells for successful tissue regeneration. However, the manner in which the cells sense the surface roughness and morphology remains unclear. Previously, we analyzed cell adhesion behavior and observed that inhibited cell spreading can delay osteoblast functions. Therefore, assuming that the surface morphology can be sensed through cell spreading, we investigated the cell spreading area and yes-associated protein (YAP) localization in mouse osteoblasts (MC3T3-E1) on a titanium surface with disordered abrasive scratches. Surface roughness of 100-150 nm was obtained by polishing, which inhibited the cell spreading, indicating that YAP localization in the nucleus was lower than that on other surfaces. The obtained results indicate that the cells sense the surface environment based on their spreading area, which regulates cellular functions via the Hippo pathway.

The Performance of Nonwoven PLLA Scaffolds of Different Thickness for Stem Cells Seeding and Implantation

The 3D reconstruction of 100 μm- and 600 μm-thick fibrous poly-L/L-lactide scaffolds was performed by confocal laser scanning microscopy and supported by scanning electron microscopy and showed that the density of the fibers on the side adjacent to the electrode is higher, which can affect cell diffusion, while the pore size is generally the same. Bone marrow mesenchymal stem cells cultured in a 600 μm-thick scaffold formed colonies and produced conditions for cell differentiation. An in vitro study of stem cells after 7 days revealed that cell proliferation and hepatocyte growth factor release in the 600 μm-thick scaffold were higher than in the 100 μm-thick scaffold. An in vivo study of scaffolds with and without stem cells implanted subcutaneously onto the backs of recipient mice was carried out to test their biodegradation and biocompatibility over a 0-3-week period. The cells seeded onto the 600 μm-thick scaffold promoted significant neovascularization in vivo. After 3 weeks, a significant number of donor cells persisted only on the inside of the 600 μm-thick scaffold. Thus, the use of bulkier matrices allows to prolong the effect of secretion of growth factors by stem cells during implantation. These 600 μm-thick scaffolds could potentially be utilized to repair and regenerate injuries with stem cell co-culture for vascularization of implant.

Effect of microtopography on osseointegration of implantable biomaterials and its modification strategies

Orthopedic implants are widely used for the treatment of bone defects caused by injury, infection, tumor and congenital diseases. However, poor osseointegration and implant failures still occur frequently due to the lack of direct contact between the implant and the bone. In order to improve the biointegration of implants with the host bone, surface modification is of particular interest and requirement in the development of implant materials. Implant surfaces that mimic the inherent surface roughness and hydrophilicity of native bone have been shown to provide osteogenic cells with topographic cues to promote tissue regeneration and new bone formation. A growing number of studies have shown that cell attachment, proliferation and differentiation are sensitive to these implant surface microtopography. This review is to provide a summary of the latest science of surface modified bone implants, focusing on how surface microtopography modulates osteoblast differentiation in vitro and osseointegration in vivo, signaling pathways in the process and types of surface modifications. The aim is to systematically provide comprehensive reference information for better fabrication of orthopedic implants.

Engineering cell-substrate interactions on porous membranes for microphysiological systems

Microphysiological systems are now widely used to recapitulate physiological and pathological microenvironments in order to study and understand a variety of cellular processes as well as drug delivery and stem cell differentiation. Central to many of these systems are porous membranes that enable tissue barrier formation as well as compartmentalization while still facilitating small molecule diffusion, cellular transmigration and cell-cell communication. The role or impact of porous membranes on the cells cultured upon them has not been widely studied or reviewed. Although many chemical and physical substrate characteristics have been shown to be effective in controlling and directing cellular behavior, the influence of pore characteristics and the ability to engineer porous membranes to influence these responses is not fully understood. In this mini-review, we show that many studies point to a multiphasic cell-substrate response, where increasing pore sizes and pore-pore spacing generally leads to improved cell-substrate interactions. However, the smallest pores in the nano-scale sometimes promote the strongest cell-substrate interactions, while the very largest micron-scale pores hinder cell-substrate interactions. This synopsis provides an insight into the importance of membrane pores in controlling cellular responses, and may help with the design and utilization of porous membranes for induction of desired cell processes in the development of biomimetic platforms.

Disrupted Surfaces of Porous Membranes Reduce Nuclear YAP Localization and Enhance Adipogenesis through Morphological Changes

The disrupted surface of porous membranes, commonly used in tissue-chip and cellular coculture systems, is known to weaken cell-substrate interactions. Here, we investigated whether disrupted surfaces of membranes with micron and submicron scale pores affect yes-associated protein (YAP) localization and differentiation of adipose-derived stem cells. We found that these substrates reduce YAP nuclear localization through decreased cell spreading, consistent with reduced cell-substrate interactions, and in turn enhance adipogenesis while decreasing osteogenesis.

Regulation of cell attachment, spreading, and migration by hydrogel substrates with independently tunable mesh size

Hydrogels are widely used as substrates to investigate interactions between cells and their microenvironment as they mimic many attributes of the extracellular matrix. The stiffness of hydrogels is an important property that is known to regulate cell behavior. Beside stiffness, cells also respond to structural cues such as mesh size. However, since the mesh size of hydrogel is intrinsically coupled to its stiffness, its role in regulating cell behavior has never been independently investigated. Here, we report a hydrogel system whose mesh size and stiffness can be independently controlled. Cell behavior, including spreading, migration, and formation of focal adhesions is significantly altered on hydrogels with different mesh sizes but with the same stiffness. At the transcriptional level, hydrogel mesh size affects cellular mechanotransduction by regulating nuclear translocation of yes-associated protein. These findings demonstrate that the mesh size of a hydrogel plays an important role in cell-substrate interactions. STATEMENT OF SIGNIFICANCE: Hydrogels are ideal platforms with which to investigate interactions between cells and their microenvironment as they mimic many physical properties of the extracellular matrix. However, the mesh size of hydrogels is intrinsically coupled to their stiffness, making it challenging to investigate the contribution of mesh size to cell behavior. In this work, we use hydrogel-on-glass substrates with defined thicknesses whose stiffness and mesh size can be independently tuned. We use these substrates to isolate the effects of mesh size on cell behavior, including attachment, spreading, migration, focal adhesion formation and YAP localization in the nucleus. Our results show that mesh size has significant, yet often overlooked, effects, on cell behavior, and contribute to a further understanding of cell-substrate interactions.

Nano-Hydroxyapatite Bone Scaffolds with Different Porous Structures Processed by Digital Light Processing 3D Printing

The morphologies and structures of the scaffold have a significant influence on their mechanical and biological properties. In this work, different types of porous structures: Triply periodic minimal surface-Schwarz primitive (P), body-centered cubic, and cubic pore-shaped (CPS) hydroxyapatite scaffolds with ~70% porosity were fabricated through digital light processing (DLP) 3D printing technology. The compressive properties and in vitro cell evaluations such as cell proliferation and attachment morphology of these scaffolds were systematically compared. The results showed that the CPS scaffolds exhibited the highest compressive strength (~22.5 MPa) and modulus (~400 MPa). In addition, the CPS scaffolds also performed the most active cell metabolisms as compared to other two structures, which may account for the larger pore size and smaller curvature of the substrate. This study provides a general guidance for the fabrication and selection of porous bone scaffolds processed by DLP 3D printing.

A Hierarchical-Structured Mineralized Nanofiber Scaffold with Osteoimmunomodulatory and Osteoinductive Functions for Enhanced Alveolar Bone Regeneration

Alveolar bone resorption is a major cause of teeth loss and jeopardizes the osseointegration of dental implants, greatly affecting patient's quality of life and health. It is still a great challenge to completely regenerate the alveolar bone defect through traditional guided bone regeneration (GBR) membranes due to their limited bioactivity and regeneration potential. Herein, a new hierarchical-structured mineralized nanofiber (HMF) scaffold, which is combined with both anisotropic and isotropic nanofibrous surface topography and the mineralized particles, is fabricated via a simple template-assisted electrospinning technology and in situ mineralization method. This HMF scaffold can not only directly induce osteogenic differentiation of bone mesenchymal stem cells (osteoinduction), but also stimulate macrophage toward pro-healing (M2) phenotype-polarization with an elevated secretion of the pro-healing cytokines, eventually enhancing the osteogenesis (osteoimmunomodulation). The results of in vivo rat alveolar bone defect repair experiments demonstrate that as compared with the combination of commercial Bio-Gide and Bio-Oss, the single HMF scaffold shows comparable or even superior bone repair effect, with better tissue-integration and more suitable degradation time and accompanied by a simplified operation.

Effect of Controlled Microtopography on Osteogenic Differentiation of Mesenchymal Stem Cells

Various kinds of controlled microtopographies can promote osteogenic differentiation of mesenchymal stem cells (MSCs), such as microgrooves, micropillars, and micropits. However, the optimal shape, size, and mechanism remain unclear. In this review, we summarize the relationship between the parameters of different microtopographies and the behavior of MSCs. Then, we try to reveal the potential mechanism between them. The results showed that the microgrooves with a width of 4–60 μm and ridge width <10 μm, micropillars with parameters less than 10 μm, and square micropits had the full potential to promote osteogenic differentiation of MSCs, while the micromorphology of the same size could induce larger focal adhesions (FAs), well-organized cytoskeleton, and superior cell areas. Therefore, such events are possibly mediated by microtopography-induced mechanotransduction pathways.

Comparison of surface properties, cell behaviors, bone regeneration and osseointegration between nano tantalum/PEEK composite and nano silicon nitride/PEEK composite

Both tantalum (Ta) and silicon nitride (SN) exhibit osteogenic bioactivity and antibacterial property. In addition, as a biomaterial for bone repair, polyetheretherketone (PEEK) has outstanding biocompatibility and mechanical performances while it is biologically inert. In this study, by blending PEEK with Ta and SN nanoparticles, respectively, Ta/PEEK composite (TPC) and SN/PEEK composite (SPC) were fabricated for load-bearing bone repair. The surface roughness, hydrophilicity and surface energy of TPC containing Ta nanoparticles were higher than SPC containing SN nanoparticles and PEEK. In addition, TPC with Ta nanoparticles exhibited low antibacterial property while SPC with SN nanoparticles showed high bacterial property. Moreover, the MC3T3-E1 cells responses (e.g. proliferation and differentiation) to TPC was the highest while PEEK was the lowest in vitro. Furthermore, new bone formation and osseointegration for TPC was the highest while PEEK was the lowest in vivo. In conclusion, compared with PEEK, addition of Ta and SN nanoparticles into PEEK fabricated bioactive composites of TPC and SPC with optimized surface property, which played crucial roles in inducing cellular response/bone regeneration. Although the osteogenic activity of SPC was lower than TPC, SPC exhibited osteogenic activity and good antibacterial property, which could prevent infection from bacterial. Therefore, SPC would have better potential for bone substitute.

Hydrothermal Synthesis of Biphasic Calcium Phosphate from Cuttlebone Assisted by the Biosurfactant L-rhamnose Monohydrate for Biomedical Materials

The motivation of this research work is to develop novel medical material from cuttlebone (calcium source) by L-rhamnose monohydrate (biosurfactant) for aged people. The process can be synthesized biphasic calcium phosphate which is eco-friendly to environment. One of the most important aspects for this work is to use cuttlebone as a naturally occurring calcium source from a local beach in Thailand. It usually contains 90% calcium carbonate. The objective of this research work is to synthesize the biphasic calcium phosphate by hydrothermal reaction. Critical micelle concentrations (CMCs) of 10, 20, 100, 500 and 1000 of L-rhamnose monohydrate were used to control particle size and shape. XRD revealed a mixture of β-tricalcium phosphate and hydroxyapatite powder. SEM reported that the size of particles can be effectively controlled by the addition of L-rhamnose monohydrate, and with the addition of surfactant, size uniformity was achieved. The cytotoxicity test was reported to be in the range of 70–75%. It was remarkable to note that biphasic calcium phosphate synthesized from cuttlebone with the aid of L-rhamnose monohydrate will be considered an excellent candidate as a scaffold material.

Effects of compound stimulation of fluid shear stress plus ultrasound on stem cell proliferation and osteogenesis

Bone tissue with strong adaptability is often in a complex dynamical microenvironment in vivo, which is associated with the pathogenesis and treatment of orthopedic diseases. Therefore, it is of great significance to investigate the effects of corresponding compound stimulation on cell behaviors. Herein, a fluid shear stress (FSS) plus ultrasound stimulation platform suitable for cell studies based on a microfluidic chip was constructed and bone marrow mesenchymal stem cell (BMSC) was chosen as a model cell. The proliferation and osteogenesis of BMSCs under the compound stimulation of FSS plus ultrasound in growth medium without any soluble induction factors were firstly investigated. Single FSS stimulation and static culture conditions were also examined. Results illustrated that suitable single FSS stimulation (about 0.06 dyn/cm²) could significantly enhance cell proliferation and osteogenesis simultaneously when compared to the static control, while greater FSS mitigated or even restricted these enhancing effects. Interestingly, ultrasound stimulation combined with this suitable FSS stimulation further accelerated cell proliferation as the intensity of ultrasound increasing. As for the osteogenesis under compound stimulation, it was relatively restricted under lower ultrasound intensity (about 0.075 W/cm²), while promoted when the intensity became higher (about 1.75 W/cm²). This study suggests that both the cell proliferation and osteogenesis are very responsive to the magnitudes of FSS and ultrasound stimulations and can be both significantly enhanced by proper combination strategies. Moreover, these findings will provide valuable references for the construction of effective cell bioreactors and also the treatment of orthopedic diseases.

Mechanotopography-Driven Design of Dispersible Nanofiber-Laden Hydrogel as a 3D Cell Culture Platform for Investigating Tissue Fibrosis

Fibrosis is one of the most frequent occurrences during one's lifetime, identified by various physiological changes including, most notably, excessive deposition of extracellular matrix (ECM). Despite its physiological importance, it is still a significant challenge to conduct a systematic investigation of tissue fibrosis, mainly due to the lack of in vitro 3D tissue model that can accurately portray the characteristic features of fibrotic events. Herein, a hybrid hydrogel system incorporating dispersible nanofibers is developed to emulate highly collagenous deposits formed within a fibrotic tissue leading to altered mechanotopographical properties. Micrometer-length, aqueous-stable nanofibers consisting of crosslinked gelatin network embedded with graphene oxide (GO) or reduced graphene (rGO) are infused into hydrogel, resulting in controllable mechanotopographical properties while maintaining permeability sufficiently enough for various cellular activities. Ultimately, the ability to induce fibrotic behavior of fibroblasts cultured in these mechanotopography-controlled, nanofiber-laden hydrogels is investigated in detail.

Influence of sterilization on the performance of anodized nanoporous titanium implants

Towards clinical translation of bioactive nano-engineered titanium implants, achieving appropriate sterilization and understanding its influence on the modified implant characteristics is essential. With limited studies exploring the influence of sterilization techniques on electrochemically anodized titanium with TiO₂ nanostructures, we aimed to advance this domain by performing an in-depth evaluation of the influence of common sterilization techniques (ethanol immersion, various UV irradiation times, gamma irradiation, and dry/wet autoclaving) on TiO₂ nanopores fabricated on micro-rough Ti surfaces (dual micro-nano) via single step anodization. Various sterilized surfaces were systematically compared in terms of topographical, chemical, crystalline, wettability and mechanical characteristics. Next, we investigated the protein adhesion capacity and functions of primary gingival fibroblasts (proliferation, adhesion/alignment and spreading morphology) to compare the bioactivity of the sterilized nanopores. Ethanol immersion, gamma irradiation and UV irradiation conserved the topography of the fabricated nanopores, while autoclave sterilization (both dry and wet) compromised the nanoporous structures. Various duration of UV-sterilization resulted in no significant changes in the surface topography and chemistry of the fabricated TNPs. Our findings revealed that UV irradiation is the most appropriate technique to sterilize nano-engineered titanium implants for appropriate wettability, protein adhesion capacity and enhanced metabolism and proliferation of human gingival fibroblasts (hGFs). This study systematically investigated the influence of sterilization on anodized nano-engineered titanium implants towards achieving reproducible outcomes (in terms of topography, chemistry and bioactivity), and found that UV irradiation holds great promise for application across different nano-engineered metal surfaces.

Engineering hydrogels with homogeneous mechanical properties for controlling stem cell lineage specification

Hydrogels are extensively used for cell culture, tissue engineering, and flexible electronics. In all of these applications, mechanical properties of hydrogels play an important role. Although tremendous studies have been devoted to optimizing the stiffness, strain, toughness, and dynamic mechanical response, the mechanical homogeneity of hydrogels has rarely been considered. By developing a general strategy to control the mechanical homogeneity of hydrogels, here we show that nanoscale variation in matrix stiffness can considerably affect the lineage specification of human embryonic stem cells. Inhomogeneous hydrogels suppress mechanotransduction and facilitate stemness maintenance, while homogenous hydrogels promote mechanotransduction and osteogenic differentiation. Therefore, engineering hydrogels with controllable and well-defined nanoscale homogeneity may have considerable implications in stem cell culture and regenerative medicine.

The extracellular matrix (ECM) is mechanically inhomogeneous due to the presence of a wide spectrum of biomacromolecules and hierarchically assembled structures at the nanoscale. Mechanical inhomogeneity can be even more pronounced under pathological conditions due to injury, fibrogenesis, or tumorigenesis. Although considerable progress has been devoted to engineering synthetic hydrogels to mimic the ECM, the effect of the mechanical inhomogeneity of hydrogels has been widely overlooked. Here, we develop a method based on host–guest chemistry to control the homogeneity of maleimide–thiol cross-linked poly(ethylene glycol) hydrogels. We show that mechanical homogeneity plays an important role in controlling the differentiation or stemness maintenance of human embryonic stem cells. Inhomogeneous hydrogels disrupt actin assembly and lead to reduced YAP activation levels, while homogeneous hydrogels promote mechanotransduction. Thus, the method we developed to minimize the mechanical inhomogeneity of hydrogels may have broad applications in cell culture and tissue engineering.

Facile surface functional polyetheretherketone with antibacterial and immunoregulatory activities for enhanced regeneration toward bacterium-infected bone destruction

Existing biologically inert or unmodified implants to treat infectious bone defects or osteomyelitis still cannot effectively solve bacterial infection and osseointegration. In this work, a simple co-deposition strategy was developed to modify porous polyetheretherketone (PEEK) with improved antibacterial activity and controllable immunoregulatory ability. After PEEK was treated by H₂SO₄ to obtain porous PEEK (SPEEK), the self-polymerization of dopamine was operated on SPEEK in the solution of dopamine and gentamicin sulfate (GS) to prepare polydopamine (pDA) and GS layer-modified SPEEK (labeled as SPEEK–pDA–GS). The morphology, surface property, and molecular structure of SPEEK–pDA–GS were investigated. Besides the antibacterial property of SPEEK–pDA–GS ascribed to the successful immobilization of GS, SPEEK–pDA–GS exhibited promoted osseointegration through the results of mineralization, alkaline phosphatase (ALP) levels and osteogenic gene expression. Furthermore, the evaluation of the cell proliferation suggested that SPEEK–pDA–GS possessed the biocompatibility and the immunoregulatory ability that induced macrophages to anti-inflammatory M2 phenotype. Using rat as model, in vivo results containing X-ray, μ-CT, immunohistochemistry, and pathological analysis showed the excellent healing effect of SPEEK–pDA–GS on bone defect with infection with biological safety. This work illustrates a new insight into the simple and effective modification of PEEK and other implants with antibacterial, immunoregulatory, and osseointegration abilities for clinical requirement.

Effect of Morphological Characteristics and Biomineralization of 3D-Printed Gelatin/Hyaluronic Acid/Hydroxyapatite Composite Scaffolds on Bone Tissue Regeneration

The use of porous three-dimensional (3D) composite scaffolds has attracted great attention in bone tissue engineering applications because they closely simulate the major features of the natural extracellular matrix (ECM) of bone. This study aimed to prepare biomimetic composite scaffolds via a simple 3D printing of gelatin/hyaluronic acid (HA)/hydroxyapatite (HAp) and subsequent biomineralization for improved bone tissue regeneration. The resulting scaffolds exhibited uniform structure and homogeneous pore distribution. In addition, the microstructures of the composite scaffolds showed an ECM-mimetic structure with a wrinkled internal surface and a porous hierarchical architecture. The results of bioactivity assays proved that the morphological characteristics and biomineralization of the composite scaffolds influenced cell proliferation and osteogenic differentiation. In particular, the biomineralized gelatin/HA/HAp composite scaffolds with double-layer staggered orthogonal (GEHA20-ZZS) and double-layer alternative structure (GEHA20-45S) showed higher bioactivity than other scaffolds. According to these results, biomineralization has a great influence on the biological activity of cells. Hence, the biomineralized composite scaffolds can be used as new bone scaffolds in bone regeneration.

Effect of poly (lactic acid) porous membrane prepared via phase inversion induced by water droplets on 3T3 cell behavior

Phase inversion induced by water droplets has garnered attention in the field of polymer science as a novel method for preparing porous membranes. This study investigates the effect of the porous structure of poly (lactic acid) (PLA) membranes prepared through phase inversion induced by water droplets at four different temperatures (25, 50, 75, and 100 °C) on the morphology and proliferation of 3T3 cells. The surface properties of the PLA porous membrane, including pore size, pore size distribution, surface roughness, surface hydrophilicity, and cytocompatibility with 3T3 cells, were evaluated. The results indicated that the synthesized PLA membrane had two surfaces with different structures. The upper surface in contact with the water droplets during preparation contained uniformly distributed micropores, whereas the bottom surface was smooth and composed of small particles in contacted with the mold. The upper surface showed high cytocompatibility with 3T3 cells, and the 3T3 cells migrated and grew within the pores at 25 °C. In contrast, the bottom surface exhibited low biocompatibility with the 3T3 cells. Our study has wide-ranging implications and will improve the fabrication and implementation of 3D cultured scaffolds with excellent cytocompatibility.

On the Use of Black Ti as a Bone Substituting Biomaterial: Behind the Scenes of Dual-Functionality

Despite the potential of small-scale pillars of black titanium (bTi) for killing the bacteria and directing the fate of stem cells, not much is known about the effects of the pillars' design parameters on their biological properties. Here, three distinct bTi surfaces are designed and fabricated through dry etching of the titanium, each featuring different pillar designs. The interactions of the surfaces with MC3T3-E1 preosteoblast cells and Staphylococcus aureus bacteria are then investigated. Pillars with different heights and spatial organizations differently influence the morphological characteristics of the cells, including their spreading area, aspect ratio, nucleus area, and cytoskeletal organization. The preferential formation of focal adhesions (FAs) and their size variations also depend on the type of topography. When the pillars are neither fully separated nor extremely tall, the colocalization of actin fibers and FAs as well as an enhanced matrix mineralization are observed. However, the killing efficiency of these pillars against the bacteria is not as high as that of fully separated and tall pillars. This study provides a new perspective on the dual-functionality of bTi surfaces and elucidates how the surface design and fabrication parameters can be used to achieve a surface topography with balanced bactericidal and osteogenic properties.

Mechanical, Electrochemical, and Osteoblastic Properties of Gradient Tantalum Coatings on Ti6Al4V by Prepared Plasma Alloying Technique

Plasma alloying technique capable of producing metallic coatings with metallurgical bonding has attracted much attention in dental and orthopedic fields. In this study, the effects of temperature and time of plasma tantalum (Ta) alloying technique on the mechanical, electrochemical, and osteoblastic properties of Ta coatings were systematically investigated. Ta coatings prepared at 800 °C possess better interfacial strengths than those prepared at 750 and 850 °C, and the interfacial strength increases with prolonged alloying time (30–120 min). At 800 °C, however, the increased proportion of the soft Ta deposition layer with alloying time in the whole coating impairs the surface mechanical properties of the entire coating, as convinced by decreased microhardness and wear resistance. Moreover, Ta coatings exhibit better corrosion resistance than the Ti6Al4V substrate in Dulbecco’s modified Eagle medium. The enhanced adhesion and extracellular matrix mineralization level of osteoblasts demonstrate the better cytocompatibility and osteogenic activity of the Ta coating. Ta30 (Ta coating prepared at 800 °C for 30 min) exhibits excellent mechanical, electrochemical, and osteoblastic behaviors and is promising in biomedical applications.

Synergistic Effect of Biomaterial and Stem Cell for Skin Tissue Engineering in Cutaneous Wound Healing: A Concise Review

Skin tissue engineering has made remarkable progress in wound healing treatment with the advent of newer fabrication strategies using natural/synthetic polymers and stem cells. Stem cell therapy is used to treat a wide range of injuries and degenerative diseases of the skin. Nevertheless, many related studies demonstrated modest improvement in organ functions due to the low survival rate of transplanted cells at the targeted injured area. Thus, incorporating stem cells into biomaterial offer niches to transplanted stem cells, enhancing their delivery and therapeutic effects. Currently, through the skin tissue engineering approach, many attempts have employed biomaterials as a platform to improve the engraftment of implanted cells and facilitate the function of exogenous cells by mimicking the tissue microenvironment. This review aims to identify the limitations of stem cell therapy in wound healing treatment and potentially highlight how the use of various biomaterials can enhance the therapeutic efficiency of stem cells in tissue regeneration post-implantation. Moreover, the review discusses the combined effects of stem cells and biomaterials in in vitro and in vivo settings followed by identifying the key factors contributing to the treatment outcomes. Apart from stem cells and biomaterials, the role of growth factors and other cellular substitutes used in effective wound healing treatment has been mentioned. In conclusion, the synergistic effect of biomaterials and stem cells provided significant effectiveness in therapeutic outcomes mainly in wound healing improvement.

A State-of-the-Art of Functional Scaffolds for 3D Nervous Tissue Regeneration

Exploring and developing multifunctional intelligent biomaterials is crucial to improve next-generation therapies in tissue engineering and regenerative medicine. Recent findings show how distinct characteristics of in situ microenvironment can be mimicked by using different biomaterials. In vivo tissue architecture is characterized by the interconnection between cells and specific components of the extracellular matrix (ECM). Last evidence shows the importance of the structure and composition of the ECM in the development of cellular and molecular techniques, to achieve the best biodegradable and bioactive biomaterial compatible to human physiology. Such biomaterials provide specialized bioactive signals to regulate the surrounding biological habitat, through the progression of wound healing and biomaterial integration. The connection between stem cells and biomaterials stimulate the occurrence of specific modifications in terms of cell properties and fate, influencing then processes such as self-renewal, cell adhesion and differentiation. Recent studies in the field of tissue engineering and regenerative medicine have shown to deal with a broad area of applications, offering the most efficient and suitable strategies to neural repair and regeneration, drawing attention towards the potential use of biomaterials as 3D tools for in vitro neurodevelopment of tissue models, both in physiological and pathological conditions. In this direction, there are several tools supporting cell regeneration, which associate cytokines and other soluble factors delivery through the scaffold, and different approaches considering the features of the biomaterials, for an increased functionalization of the scaffold and for a better promotion of neural proliferation and cells-ECM interplay. In fact, 3D scaffolds need to ensure a progressive and regular delivery of cytokines, growth factors, or biomolecules, and moreover they should serve as a guide and support for injured tissues. It is also possible to create scaffolds with different layers, each one possessing different physical and biochemical aspects, able to provide at the same time organization, support and maintenance of the specific cell phenotype and diversified ECM morphogenesis. Our review summarizes the most recent advancements in functional materials, which are crucial to achieve the best performance and at the same time, to overcome the current limitations in tissue engineering and nervous tissue regeneration.

A bilayered scaffold with segregated hydrophilicity-hydrophobicity enables reconstruction of goat hierarchical temporomandibular joint condyle cartilage

Temporomandibular joint (TMJ) supports chewing, talking or other daily oral activities. So far, it still remains a great challenge to treat the defected TMJ condyle cartilage through tissue engineering technology. Herein, a bilayered scaffold is designed to fully reconstruct the different cartilage matrices of TMJ condyle under same induction condition. The bilayered scaffold with segregated hydrophobicity-hydrophilicity in top and bottom layer is prepared from a low and high content of polyethylene glycol (PEG) crosslinked poly (L-glutamic acid)-g-polycaprolactone (PLGA-g-PCL). The hydrophobic aggregates in top layer support the adhesion and spread of bone mesenchymal stem cells (BMSCs), thus inducing the differentation towards fibrocartilage; while aggregates (spheroids) are formed on the hydrophlic bottom layer, showing a preferable hyaline differentiation pathway under same chondrogenic induction in vitro. After 14 d in vitro induction, the scaffold/BMSCs construct is implanted in goat TMJ condyle defects. The post-operative outcome after 2 months demonstrates that the defects are fully covered by neo-cartilage. And the regenerated hierarchical TMJ condyle cartilage perfectly consist of ordered fibrocartilage and hyaline cartilage, which is same as natural condyle cartilage. These results corroborate that this bilayered scaffold with segregated hydrophilicity-hydrophobicity carrying induced BMSCs is a promising for treatment of TMJ condyle cartilage defects.

Additive manufacturing pertaining to bone: Hopes, reality and future challenges for clinical applications

For the past 20 years, the democratization of additive manufacturing (AM) technologies has made many of us dream of: low cost, waste-free, and on-demand production of functional parts; fully customized tools; designs limited by imagination only, etc. As every patient is unique, the potential of AM for the medical field is thought to be considerable: AM would allow the division of dedicated patient-specific healthcare solutions entirely adapted to the patients' clinical needs. Pertinently, this review offers an extensive overview of bone-related clinical applications of AM and ongoing research trends, from 3D anatomical models for patient and student education to ephemeral structures supporting and promoting bone regeneration. Today, AM has undoubtably improved patient care and should facilitate many more improvements in the near future. However, despite extensive research, AM-based strategies for bone regeneration remain the only bone-related field without compelling clinical proof of concept to date. This may be due to a lack of understanding of the biological mechanisms guiding and promoting bone formation and due to the traditional top-down strategies devised to solve clinical issues. Indeed, the integrated holistic approach recommended for the design of regenerative systems (i.e., fixation systems and scaffolds) has remained at the conceptual state. Challenged by these issues, a slower but incremental research dynamic has occurred for the last few years, and recent progress suggests notable improvement in the years to come, with in view the development of safe, robust and standardized patient-specific clinical solutions for the regeneration of large bone defects.

The morphological effect of nanostructured hydroxyapatite coatings on the osteoinduction and osteogenic capacity of porous titanium

Weak osteogenic activity affects the long-term fixation and lifespan of titanium (Ti) implants. Surface modification along with a built-in porous structure is a highly considerable approach to improve the osteoinduction and osseointegration capacity of Ti. Herein, the osteoinduction and osteogenic activities of electrochemically deposited (ED) nanoplate-like, nanorod-like and nanoneedle-like hydroxyapatite (HA) coatings (named EDHA-P, EDHA-R, and EDHA-N, respectively) were evaluated in vitro and in vivo by comparison with those of acid/alkali (AA) treatment. The results revealed that the apatite forming ability of all nanostructured EDHA coatings was excellent, and only 12 h of soaking in SBF was needed to induce a complete layer of apatite. More serum proteins adsorbed on EDHA-P than others. In cellular experiments, different from those on EDHA-R and EDHA-N, the cells on EDHA-P presented a polygonal shape with lamellipodia extension, and thus exhibited a relatively larger spreading area. Furthermore, EDHA-P was more favorable for the enhancement of the proliferation and ALP activity of BMSCs, and the up-regulation of OPN gene expression. Based on the good biological performance in vitro, EDHA-P was selected to further evaluate its osteoinduction and osteogenic activities in vivo by comparison with AA treatment. Interestingly, a greater ability of ectopic osteoinduction was observed in the EDHA-P group compared to that in the AA group. At the osseous site, EDHA-P promoted more bone on/ingrowth, and had a higher area percentage of newly formed bone in the bone-implant interface and inner pores of the implants than in the AA group. Thus, a nanoplate-like HA coating has good potential in improving the osteoinductivity and osteogenic activity of porous Ti implants in clinical applications.

Using MgO nanoparticles as a potential platform to precisely load and steadily release Ag ions for enhanced osteogenesis and bacterial killing

Bio-functional fillers including bio-ceramic, degradable metallic and composite particles are commonly introduced into bone tissue engineering (BTE) scaffolds to endow the materials with specific biological functions for enhanced bone defect therapy. In this work, MgO nanoparticles (NPs) were employed as a potential platform for precise loading and sustained release of Ag⁺. The results showed that MgO NPs possessed strong adsorption capacity (almost 100%) towards Ag⁺ in AgNO₃ solutions with different concentrations (0.1, 1 and 10 mM). After the adsorption of Ag⁺ in AgNO₃ solutions, cube-shaped MgO NPs transformed to lamella-structured nano-composites (NCs) composed of Mg(OH)₂ and Ag₂O, which were referred as MgO-xAg (x = 0.1, 1 or 10) NCs depending on the employed concentration of AgNO₃ solution. After being suspended in distilled water, as-prepared positively charged NCs underwent a fast degradation process during the initial 4 days. From day 4 and 14, steady release behaviors of Mg²⁺ and/or Ag⁺ from the NCs were noticed. With the lowest loading amount of Ag⁺, MgO-0.1Ag NCs did not exhibit significant modulatory effect on SaOS-2 cell response. On the contrary, MgO-10Ag NCs loaded with the highest amount of Ag⁺ showed significant cyto-toxicity towards SaOS-2 cells. With appropriate amount of Ag⁺ loading, MgO-1Ag NCs showed significantly stimulatory effects on SaOS-2 cell proliferation and differentiation. This is evidenced by the enhanced cell viability, alkaline phosphatase (ALP) activity and collagen (COL) production as well as the gene expressions of ALP, COL and osteoprotegerin (OPG) in MgO-1Ag group. Moreover, MgO-1Ag exhibited strong bactericidal capacity against both Escherichia coli and Staphylococcus aureus. Together, the results indicate that MgO could be employed as a potential platform for precise loading and sustained release of Ag⁺. MgO-1Ag NCs are promising to be used as bio-functional fillers in BTE scaffolds for simultaneously promoted osteogenesis and bacterial killing.