Biomass activated carbon derived from pine sawdust with steam bursting pretreatment; perfluorooctanoic acid and methylene blue adsorption

Structural properties and adsorption performance relationship towards three categories of lignin and their derived biochar

The growing interest in utilizing lignin for dye removal has gained momentum, but there is limited information on the intricate relationship between lignin structural characteristics and adsorption efficacy, especially for its biochar derivatives. This study focused on three types of lignin and their corresponding biochar derivatives. Among them, ZnCl2-activated acidic/alkali densified lignin preparation of lignin-derived active carbon exhibited superior adsorption performance, achieving 526.32 mg/g for methylene blue and 2156.77 mg/g for congo red. Its exceptional adsorption capacity was attributed to its unique structural properties, including low alkyl and O-alkyl group content and high aromatic carbon levels. Furthermore, the adsorption mechanisms adhered to pseudo-second-order kinetics and the Langmuir model, signifying a spontaneous process. Intriguingly, lignin-derived active carbon also demonstrated remarkable recovery capabilities. These findings provide valuable insights into the impact of structural attributes on lignin and its biochar's adsorption performance.

Application of chemically modified waste tucumã (Astrocaryum aculeatum) seeds in the biosorption of methylene blue: kinetic and thermodynamic parameters

Dye effluents cause diverse environmental problems. Methylene blue (MB) dye stands out since it is widely used in the textile industry. To reduce the pollution caused by the MB, we developed biosorbents from tucumã seeds, where the in natura seeds were treated with NaOH (BT) and H3PO4 (AT) solutions and characterized by Boehm titration, point of zero charges, FTIR, TGA, BET, and SEM. It was observed that the acid groups predominate on the surface of the three biosorbents. The process was optimized for all biosorbents at pH = 8, 7.5 g/L, 240 min, C0 = 250 mg/L, and 45 ℃. BT was more efficient in removing MB (96.20%; QMax = 35.71 mg/g), while IT and AT removed around 60% in similar conditions. The adsorption process best fits Langmuir and Redlich-Peterson isotherms, indicating a hybrid adsorption process (monolayer and multilayer) and pseudo-second-order kinetics. Thermodynamic data confirmed an endothermic and spontaneous adsorption process, mainly for BT. MB was also recovered through a desorption process with ethanol, allowing the BT recycling and reapplication of the dye. Thus, an efficient and sustainable biosorbent was developed, contributing to reducing environmental impacts.

Optimization of microwave-expanding pretreatment and microwave-assisted extraction of hemicellulose from bagasse cells with the exploration of the extracting mechanism

Hemicellulose is mainly distributed in the tightly packed S2 layer of the plant cell wall and the middle lamella. This rigid microstructure of wood and interactions among hemicellulose, lignin, and cellulose jointly restrict the separation and transformation of hemicellulose in the wood matrix. To address this issue, a method combined with microwave-expanding pretreatment (MEP) and microwave-assisted extraction (MAE) with a NaOH solution was carried out. We found that the MEP could effectively create new pathways for bagasse cells in mass transferring. More specifically, 195 % of the specific surface area (m2/g) with 193 % of the pores (>50 nm) increased after MEP; the SEM images also confirmed that the microstructure of bagasse was modified. MAE could considerably exfoliate hemicellulose from cellulose fiber and accelerate mass transfer. Additionally, we optimized MEP and MAE by using response surface methodology (RSM). The optimal parameters were 370 K, 3.7 min, 1081 W microwave power, and 9.9 wt% NH4HCO3 consumption for the MEP and 1100 W microwave power, 2.5 wt% NaOH concentration, 34.6 min reaction time for MAE, respectively. Moreover, molecular dynamics (MD) simulation suggests that NaOH could significantly lower the work needed to peel off the xylan chain from cellulose nanofibril.

Baking-inspired pore regulation strategy towards a hierarchically porous carbon for ultra-high efficiency cationic/anionic dyes adsorption

Converting waste resource into porous carbon toward contaminant capturing is a crucial strategy for realizing "treating waste with waste". Inspired by bread baking process, the soybean meal activated carbon (SAC) with multimodal pore structures was developed via thermally remodeling the pores of waste soybean meal. The obtained SAC-3-800 has ultra-high specific surface area (3536.952 m2/g), as well as a hierarchically porous structure. SAC-3-800 exhibits extremely high adsorption capacity for methylene blue (MB) (3015.59 mg/g), methyl orange (MO) (6486.30 mg/g), and mixed dyes (8475.09 mg/g). The hierarchically porous structure enabled fast adsorption kinetics of SAC-3-800 for MB and MO (∼30 min). Additionally, SAC-3-800 shows excellent dynamic adsorption and regeneration performance, exhibiting great potential for industrial applications. This work showcases a feasible method for synthesizing hierarchically porous carbon with outstanding adsorption performance that can simultaneously achieve efficient treatment of dye-wastewater and value-added utilization of waste resources.

Statistical physics modeling study of an environmentally friendly and efficient adsorbent derived from the brown macroalgae Bifurcaria bifurcata for the removal of Bisphenol A

The brown macroalgae Bifurcaria bifurcata was valued and used to develop a carbonaceous material activated by H2SO4 (AC-BB@H2SO4), with the goal of assessing its adsorption ability against Bisphenol A (BPA). During the adsorption experiments, the effects of the adsorbent dose, solution pH, and contact time were examined, and the results were m = 0.4 g/L, pH = 8.3, and t = 120 min, with an elimination yield of 91.6 %. With comparatively high R2 values, the pseudo-second-order kinetic model perfectly fitted the experimental data. Langmuir's model was found to be the best appropriate for describing the adsorption equilibrium of BPA on AC-BB@H2SO4. The thermodynamic findings show that BPA adsorption on AC-BB@H2SO4 was spontaneous, favorable, and endothermic in nature. Even after six cycles of reuse, regeneration testing demonstrated that our adsorbent could eliminate BPA by >50 %. The BPA adsorption mechanism's statistical physics control parameters were determined and analyzed. BPA's adsorption energies were <40 kJ/mol, indicating that the interactions between BPA and AC-BB@H2SO4 were governed by physical forces (i.e., hydrogen bonding and van der Waals and electrostatic interactions). All of these intriguing findings indicate that our carbonaceous material might have direct ramifications in the field of wastewater treatment, notably for the clearance of BPA, which is difficult to biodegrade.

Enhancing efficient reclaim of phosphorus from simulated urine by magnesium-functionalized biochar: Adsorption behaviors, molecular-level mechanistic explanations and its potential application

Magnesium-functionalized Magnolia grandiflora Linn leaf-derived biochar (MBC) capable of efficiently reclaiming phosphorus from urine was synthesized by slow co-pyrolysis. Four adsorption kinetic and seven adsorption isotherm models were fitted to the batch adsorption and desorption experimental data, and it was found that pseudo-first-order kinetic model and multilayer model with saturation best described the phosphate-phosphorus (PO43--P) adsorption process by MBC. MBC and phosphorus-saturated MBC (P-MBC) were found to offer outstanding phosphorus adsorption and slow release properties, respectively. Based on material characterization, statistical physics, adsorption energy distribution and statistical thermodynamics, a multi-ionic, inclined orientation, entropy-driven spontaneous endothermic process of MBC on PO43--P was proposed, involving physicochemical interactions (porous filling, electrostatic attraction, ligand exchange and surface precipitation). Further, seed germination and early seedling growth experiments proved that P-MBC can be used as a slow-release fertilizer. Overall, MBC offers prospective applications as an efficient phosphorus adsorbent and then as a slow-release fertilizer.

Turning waste avocado stones and montmorillonite into magnetite-supported nanocomposites for the depollution of methylene blue: adsorbent reusability and performance optimization

The existence of methylene blue (MB) in wastewater even as traces is raising environmental concerns. In this regard, the performances of four adsorbents, avocado stone biochar (AVS-BC), montmorillonite (MMT), and their magnetite Fe3O4-derived counterparts, were compared. Results showed the superior performance of Fe3O4@AVS-BC and Fe3O4@MMT nanocomposites with removal percentages (%R) of 95.59% and 88%. The morphological features of AVS-BC as revealed by SEM analysis showed a highly porous surface compared to a plane and smooth surface in the case of MMT. Surface analysis using FT-IR and Raman spectroscopies corroborated the existence of the Fe-O peaks upon loading with magnetite. The XRD analysis confirmed the formation of cubic magnetite nanoparticles. The adsorption process in the batch mode was optimized using central composite design (CCD). Equilibrium and kinetic isotherms showed that the adsorption of MB onto Fe3O4@AVS-BC fitted well with the Langmuir isotherm and the pseudo-second-order (PSO) model. The maximum adsorption capacity (qm) was 118.9 mg/g (Fe3O4@AVS-BC) and 72.39 mg/g (Fe3O4@MMT). The Fe3O4@AVS-BC showed a higher selectivity toward MB compared to other organic contaminants. The MB-laden adsorbent was successfully used for the remediation of Cr (III), Ni (II), and Cd (II) with removal efficiencies hitting 100% following thermal activation.

Adsorption of perfluorooctanoic carboxylic and heptadecafluorooctane sulfonic acids via magnetic chitosan: isotherms and modeling

This paper evaluates the adsorption mechanism of perfluorooctanoic carboxylic acid (PFCA) and heptadecafluorooctane sulfonic acid (HFOSA) on magnetic chitosan for the first time via a statistical physics modeling. Magnetic chitosan (MC-CoFe2O4) was produced from shrimp wastes and used in standard batch adsorption systems to remove PFCA and HFOSA. The experimental isotherms indicated that the maximum adsorption capacities ranged from 14 to 27.12 mg/g and from 19.16 to 45.12 mg/g for PFCA and HFOSA, respectively, where an exothermic behavior was observed for both compounds. The adsorption data were studied via an advanced model hypothesizing that a multilayer process occurred for these adsorption systems. This theoretical approach indicated that the total number of formed layers of PFCA and HFOSA adsorbates is about 3 (Nt = 2.83) at high temperatures (328 K) where a molecular aggregation process was noted during the adsorption. The maximum saturation-multilayer adsorption of PFCA and HFOSA on magnetic chitosan was 30.77 and 50.26 mg/g, respectively, and the corresponding adsorption mechanisms were successfully investigated. Two energies were responsible for the formed adsorbate layer directly on the surface and the vertical layers were computed and interpreted, reflecting that physical interactions were involved to bind these molecules on the adsorbent surface at different temperatures where the calculated adsorption energies ranged from 14 to 31 kJ/mol. Overall, this work provides theoretical insights to understand the adsorption mechanism of PFCA and HFOSA using the statistical physics modeling and its results can be used to improve the adsorbent performance for engineering applications.

The Principle of Steam Explosion Technology and Its Application in Food Processing By-Products

Steam explosion technology is an emerging pretreatment method that has shown great promise for food processing due to its ability to efficiently destroy the natural barrier structure of materials. This narrative review summarizes the principle of steam explosion technology, its similarities and differences with traditional screw extrusion technology, and the factors that affect the technology. In addition, we reviewed the applications in food processing by-products in recent years. The results of the current study indicate that moderate steam explosion treatment can improve the quality and extraction rate of the target products. Finally, we provided an outlook on the development of steam explosion technology with a reference for a wider application of this technology in the food processing field.

Enhanced adsorption of 2,4-dichlorophenoxyacetic acid using low-temperature carbonized Peltophorum pterocarpum pods and its statistical physics modeling

The usage of various herbicides in the agricultural field leads to water pollution which is a big threat to the environment. Herein, the pods of the Peltophorum pterocarpum tree were used as a cheap resource to synthesize activated carbon (AC) by low-temperature carbonization to remove 2,4-dichlorophenoxyacetic acid (2,4-D) - an abundantly used herbicide. The exceptional surface area (1078.34 m²/g), mesoporous structure, and the various functional groups of the prepared AC adsorbed 2,4-D effectively. The maximum adsorption capacity was 255.12 mg/g, significantly higher than the existing AC adsorbents. The adsorption data satisfactorily modelled using Langmuir and pseudo-second-order models. Also, the adsorption mechanism was studied using a statistical physics model which substantiated the multi-molecular interaction of 2,4-D with the AC. The adsorption energy (<20 kJ/mol) and thermodynamic studies (ΔH°: -19.50 kJ/mol) revealed the physisorption and exothermicity. The practical application of the AC was successfully tested in various waterbodies by spiking experiments. Hence, this work confirms that the AC prepared from the pods of P. pterocarpum can be applied as a potential adsorbent to remove herbicides from polluted waterbodies.

Enhanced removal of organophosphate esters by iron-modified biochar with developed mesoporous: Performance and mechanism based on site energy distribution theory

Removing the widely concerned pollutant of organophosphate esters (OPEs) by agriculture waste biochar is an effective way to address the waste and pollutant problem simultaneously. In this work, an iron-modified coconut shell biochar (MCSB) was prepared by co-pyrolysis method and used to adsorb tris(2-chloroethyl) phosphate (TCEP) and tris(1-chloro-2-propyl) phosphate (TCPP), which were two typical OPEs. The attention was focused on comprehensively investigating the adsorption behaviors to study the adsorption mechanisms of TCEP and TCPP onto MCSB. With the development of mesoporous and formation of γ-Fe₂O₃ in MCSB, the adsorption equilibrium was quickly reached in 60 min with the Langmuir maximum adsorption capacities of 211.3 mg/g for TCEP and 223.7 mg/g for TCPP, respectively. Results of adsorption kinetics and isotherm showed the heterogeneous and multilayer of the adsorption process. Pore-filling interaction, the Lewis acid-base interaction, and the hydrophobic interaction were considered to drive the adsorption. And the site energy distribution theory was introduced to further reveal that the physisorption was the main adsorption mechanism, while the Lewis acid-base interaction was responsible for the differences in adsorption of TCEP and TCPP onto MCSB. Additionally, the excellent adsorption performances of MCSB in various circumstances and fixed-bed column experiments suggested that the MCSB would be a promising adsorbent for OPEs removal.

Hierarchical porous biochar from kelp: Insight into self-template effect and highly efficient removal of methylene blue from water

Biochar is known to efficiently remove dyes especially for biochar with hierarchical pores and partial N-species. Here, a facile pyrolysis is used to yield N-doped biochar from kelp without additives, showing surface areas of 771 m2/g as temperature up to 1000 °C and hierarchical small-sized mesopores (2-4 nm) and wide meso-macropores (8-60 nm). A possible self-template mechanism from inorganics is proposed to form hierarchical pore architecture in biochar and used for methylene blue (MB) removal. Biochar pyrolyzed at 1000 °C is found to be efficient for MB removal with uptake of 379.8 mg/g under ambient conditions, one of the largest ever recorded uptakes for other biochar without activation, owing to synergistic effects of high surface areas, mesopores, and graphitized N-species. These results confirm that a facile pyrolysis for transformation of kelp into efficient dyes adsorbent is a cost-effective process for economic and environmental protection.

Drying enables multiple reuses of activated carbon without regeneration

Traditional regeneration of activated carbon is usually carried out by high-temperature oxidation in industrial processes, which reduces the quality and performance of the adsorbent, thereby increasing costs and damaging the environment. In this study, a simple drying process is proposed to enable reuse of spent activated carbon. The feasibility and merits of this method were evaluated in batch and continuous adsorption modes using dyes as adsorbates. The batch adsorption results showed that the activated carbon could be reused seven times after a simple drying process, because it led to full occupancy of the activated carbon pores by adsorbate molecules. The cumulative adsorption capacities of the activated carbon were as high as 1005.3 mg/g for methyl orange (MO) and 954.8 mg/g for methylene blue (MB). Continuous adsorption experiments in a fixed-bed column demonstrated that the activated carbon column could be reused more than three times after simply drying. Moreover, dye molecules adsorbed by the activated carbon were not leached by the stream of dye solution during reuse. This drying method exhibits three main merits for reuse of activated carbon, including (1) remarkably reduced consumption of fresh activated carbon to 51.5% or below, (2) significantly increased recovery of high-value adsorbate from the liquid phase, and (3) potential integration of multiple steps for industrial adsorption processes.

Adsorption properties and mechanism of zinc acrylic carbon nanosphere aggregates for perfluorooctanoic acid from aqueous solution

This study found that the cross-linkable zinc acrylic nanosphere aggregates (NAs) as precursors were successfully prepared by a simple one-step synthesis route, and Zn,O dopped-carbon nanocomposites were obtained through temperature-controllable engineering, which showed excellent adsorption capacities for perfluorooctanoic acid (PFOA). A series of experiments were performed to investigate and compare carbon materials for the efficient removal of PFOA. The maximum adsorption capacities of PFOA absorbed on carbon nanospheres aggregates (CNAs) were calculated by the Langmuir (360.98 mg/g) and Sips models (309.65 mg/g). The kinetic model indicated there was chemical adsorption and physical adsorption in the adsorption process. Van der Waals force and electrostatic interactions might be the dominant mechanism of the adsorption process. Additionally, pore-filling also played a role in the adsorption process. Furthermore, the adsorption efficiency was still above 90% after five cycles. The selective adsorption ability was tested through various pollutants (metal ions and dye solutions) absorbed by the CNAs. Our results proved that carbon nanosphere aggregates (CNAs) are expected to be outstanding adsorption materials for the decontamination of PFOA from wastewater.

Adsorption of Hexavalent Chromium Using Activated Carbon Produced from Sargassum ssp.: Comparison between Lab Experiments and Molecular Dynamics Simulations

Adsorption is one of the most successful physicochemical approaches for removing heavy metal contaminants from polluted water. The use of residual biomass for the production of adsorbents has attracted a lot of attention due to its cheap price and environmentally friendly approach. The transformation of Sargassum-an invasive brown macroalga-into activated carbon (AC) via phosphoric acid thermochemical activation was explored in an effort to increase the value of Sargassum seaweed biomass. Several techniques (nitrogen adsorption, pHPZC, Boehm titration, FTIR and XPS) were used to characterize the physicochemical properties of the activated carbons. The SAC600 3/1 was predominantly microporous and mesoporous (39.6% and 60.4%, respectively) and revealed a high specific surface area (1695 m2·g-1). To serve as a comparison element, a commercial reference activated carbon with a large specific surface area (1900 m2·g-1) was also investigated. The influence of several parameters on the adsorption capacity of AC was studied: solution pH, solution temperature, contact time and Cr(VI) concentration. The best adsorption capacities were found at very acid (pH 2) solution pH and at lower temperatures. The adsorption kinetics of SAC600 3/1 fitted well a pseudo-second-order type 1 model and the adsorption isotherm was better described by a Jovanovic-Freundlich isotherm model. Molecular dynamics (MD) simulations confirmed the experimental results and determined that hydroxyl and carboxylate groups are the most influential functional groups in the adsorption process of chromium anions. MD simulations also showed that the addition of MgCl2 to the activated carbon surface before adsorption experiments, slightly increases the adsorption of HCrO4- and CrO42- anions. Finally, this theoretical study was experimentally validated obtaining an increase of 5.6% in chromium uptake.

Removal of PFASs from water by carbon-based composite photocatalysis with adsorption and catalytic properties: A review

Per- and polyfluoroalkyl substances (PFASs) are a class of persistent organic pollutants widely distributed in aquatic environments. The adsorption and photocatalytic methods have been widely used to remove PFASs in water because of their respective advantages. Still, they have apparent defects when used alone. Therefore, the adsorption and photocatalytic technologies are combined through suitable preparation methods, and the excellent properties of the two are used to synergize the treatment of organic pollutants. This strategy of "concentrating" pollutants and then degrading them in a centralized manner plays an essential role in removing trace PFASs. Nevertheless, a review focusing on this kind of adsorption photocatalyst system is lacking. This review will fill this gap and provide a reference for developing a carbon-based composite photocatalyst. Firstly, different carbon-based composite photocatalysts are reviewed in detail, focusing on the differences in various composite materials' excellent adsorption and catalytic properties. Secondly, the factors influencing the removal effect of carbon-based composite photocatalysts are discussed. Thirdly, the removal mechanism of carbon-based composite photocatalysts is summarized in detail. The removal process involves two steps: adsorption and photodegradation. The adsorption process involves multiple cooperative adsorption mechanisms, and photocatalytic degradation includes oxidative and reductive degradation. Fourthly, the comparison of adsorption-photocatalysis with common treatment techniques (including removal rate, range of adaptation, cost, and the possibility of expanding application) is summarized. Finally, the prospects of carbon-based composite photocatalysts for repairing PFASs are given by evaluating the performance of different composites.

Honeycomb-like cork activated carbon with ultra-high adsorption capacity for anionic, cationic and mixed dye: Preparation, performance and mechanism

Herein, the cork activated carbon (CAC) with excellent adsorption performance for cationic dye, anionic dye, and mixed dye was obtained by a two-step pyrolysis method. The CAC exhibits a fluffy honeycomb structure consisted of porous carbon nanosheets (100-200 nm), ultra-high specific surface area (3402.68 m²/g), and well-developed hierarchical porous structure, which offers a great deal of adsorption sites and transport channels to dye molecules. The adsorption process of all the dyes onto CAC is better described by Langmuir isotherm model and pseudo-2nd-order kinetic model. The CAC shows ultra-high adsorption capacity for methylene blue (1283.99 mg/g), rhodamine B (4067.57 mg/g), methyl orange (2666.2 mg/g), and congo red (8920.61 mg/g), with an extremely low equilibrium adsorption time (∼10 min). Collectively, this study demonstrated the potential of converting waste cork into high value-added adsorbent for the efficient purification of dye wastewater.

Activation of waste paper: Influence of varied chemical agents on product properties

Waste paper (WP) is rich in cellulose, which can be activated to produce porous carbon, bio-oil, and combustible gases. During chemical activation of WP, the use of varied chemical agents not only generates activated carbon of distinct pore structure but also bio-oil/gases of different property. In this study, the activation of WP with varied chemical agents was conducted. The distinct characteristics of activated carbon and also bio-oil/gases were correlated with the different nature of the used chemical agents. The results indicated that H₃PO₄ and ZnCl₂ catalyzed polymerization reactions for producing more bio-oil while less gases owing to their Brønsted and Lewis acidic sites. K₂C₂O₄ showed high activity for cracking/gasification reactions, forming bio-oil with higher abundance of organics with smaller π-conjugated structures. In addition, ZnCl₂ could create a very coarse porous structure with abundant macropores via destroying fiber structure in WP and promoting the growth of graphitic crystals. In comparison, K₂C₂O₄ hindered the aromatization and facilitated the formation of amorphous activated carbon. K₂C₂O₄ and ZnCl₂ were much more effective than H₃PO₄ for creating micropores and mesopores from WP, the derived activated carbon showed superior performances as the electrode of supercapacitor and adsorbent for adsorption of oxytetracycline from aqueous solution. In addition, K₂C₂O₄ as activating agent showed lower environmental impact than ZnCl₂ in terms of energy consumption, environmental pollution and the greenhouse effect.

Optimization of the Preparation of Activated Carbon from Prickly Pear Seed Cake for the Removal of Lead and Cadmium Ions from Aqueous Solution

In this study, we evaluated the use of prickly pear seed cake, a by-product of prickly pear seed oil extraction, as a new precursor for producing activated carbon by phosphoric acid activation, and the obtained carbon’s capacity for heavy metal removal from aqueous solution. Response surface methodology based on the full factorial design at two levels (24) was developed to reduce the number of experiments and reach optimal preparation conditions for the removal of cadmium and lead ions from aqueous solutions. Design Expert 11.1.2.0 Trial software was used for generating the statistical experimental design and analyzing the observed data. Factors influencing the activation process, such as carbonization temperature, activation temperature, activation time, and impregnation ratio, were studied. Responses were studied in depth with an analysis of variance to estimate their significance. Each response was outlined by a first-order regression equation demonstrating satisfactory correspondence between the predicted and experimental results as the adjusted coefficients of correlation. Based on the statistical data, the best conditions for the removal of heavy metals from aqueous solution by the obtained activated carbon were indicated. The maximum iodine number and methylene blue index were 2527.3 mg g−1 and 396.5 mg g−1, respectively, using activated carbon obtained at the following conditions: Tc = 500 °C, Ta = 500 °C, impregnation ratio = 2:1 (g H3PO4: g carbon), and activation time of two hours. The maximum adsorption reached 170.2 mg g−1 and 158.4 mg g−1 for Cd2+ and Pb2+, respectively, using activated carbon obtained at the following conditions: Tc = 600 °C, Ta = 400 °C, impregnation ratio = 2:1 (g H3PO4: g carbon), and activation time of one hour. The activated carbon obtained was characterized by Boehm titration, pH of point of zero charge (pHPZC), Brunauer–Emmett–Teller surface area (SBET), and scanning electron microscopy. Adsorption was performed according to different parameters: pH solution, adsorbent dosage, temperature, contact time, and initial concentration. Regeneration experiments proved that the obtained activated carbon still had a high removal capacity for Cd2+ and Pb2+ after five regeneration cycles.