Engineered mesoporous biochar derived from rice husk for efficient removal of malachite green from wastewaters

Potassium salts activated lignin-based biochar as an effective adsorbent for malachite green adsorption

Herein, a series of lignin-based porous carbons (LC) were prepared from sulfonated lignin through a simple and environmentally-friendly one-pot activated carbonization together with various potassium compounds as activators, and used for malachite green (MG) adsorption. The results showed that the prepared biochar, especially after K2CO3 activation, exhibited a honeycomb profile with large surface area (2107.6 m2/g) and high total pore volume (1.1591 cm3/g), having excellent efficiency for MG adsorption, and the biggest adsorption capacity was 2970.0 mg/g. The kinetic study together with thermodynamic analysis indicated that the adsorption of MG by LC-K2CO3 conformed to pseudo-second-order model and the adsorption process was spontaneous, feasible, and endothermic. Moreover, LC-K2CO3 also displayed good stability and selectivity, and can selective separate the cationic dye from binary-dye system. Furthermore, the adsorption mechanism proposed in this work manifested that the high-efficient MG adsorption by LC-K2CO3 was a result of multiple actions including hydrogen bonding, electrostatic attraction, π-π interaction and n-π interaction as well as physical absorption. The work not only provide a fundamental theory for dye removal from wastewater, but offered a new insight for lignin valorization.

Bio-derived carbon-based materials for sustainable environmental remediation and wastewater treatment

Biosynthesized nanocomposites, particularly those incorporating carbon-based materials, exhibit exceptional tunability and multifunctionality, surpassing the capabilities of conventional materials in these aspects. Developing practical solutions is critical to address environmental toxins from pharmaceuticals, heavy metals, pesticides, and dyes. Biomass waste is a readily available carbon source, which emerges as a promising material for producing biochar due to its inherent advantages: abundance, low cost, and environmentally friendly nature. This distribution mainly uses carbon-based materials (CBMs) and biomass waste in wastewater treatment. This review paper investigates several CBM types, including carbon aerogels, nanotubes, graphene, and activated carbon. The development of bio-derived carbon-based nanomaterials are discussed, along with the properties and composition of carbon materials derived from biomass waste and various cycles, such as photodegradation, adsorption, and high-level oxidation processes for natural remediation. In conclusion, this review examines the challenges associated with biochar utilization, including cost, recovery, and practical implementation.

A comparative study on the malachite green dye adsorption of chemically synthesized and green MgFe2O4 nanoparticles using gerbera floral waste extract

The situation of discharging a large amount of dyes from the textile industries has caused many adverse effects on human health and the ecosystems. Emerging bio-nanomaterials represent a new trend in efficient dye removal in aqueous media. Herein, we mention that MgFe2O4 bioprepared using gerbera extract has been successfully used to adsorb malachite green (MG) in water. A comparison was made to determine the dye removal efficiency between biogenic MgFe2O4 (MFOB) and chemical MgFe2O4 (MFOC). The spherical MFOB material exhibited a large surface area of 85.0 m2 g-1 and high crystallinity. The obtained outcomes showed that the highest adsorption capacity of MG dye was 584.49 mg g-1 at a MFOB dose of 0.05 g L-1 and MG concentration of 10 mg L-1. Higher correlation coefficients in the Langmuir isotherm suggested monolayer adsorption of MG. The Box-Behnken design and response surface method were established to optimize MG removal percentage under the conditions, i.e., initial MG concentration (10-30 mg L-1), adsorbent dose (0.02-0.08 g L-1), and pH of dye solution (6-8). MFOB had good reusability with high removal efficiencies after three continuous cycles. Post reuse, this adsorbent still showed excellent stability through the verification of their structural properties in comparison with fresh MFOB, showing potential for practical applications.

Rice husk valorisation by in situ grown MoS2 nanoflowers: a dual-action catalyst for pollutant dye remediation and microbial decontamination

Rice husk (RH) is a common agricultural waste generated during the rice milling process; however, a major portion is either burned or disposed of in landfills, posing significant environmental risks. In this study, RH waste was transformed into bio-based catalysts via delignification cum in situ growth of MoS2 (DRH-MoS2) for efficient pollutant dye removal and microbial decontamination. The developed DRH-MoS2 exhibits nanoflower-like structures with a 2H-MoS2 phase and a narrow band gap of 1.37 eV, which showed strong evidence of photocatalytic activity. With the presence of abundant hydroxyl functionality, delignified rice husk (DRH) exhibits a malachite green (MG) dye adsorption capacity of 88 mg g-1. However, in situ growth of MoS2 nanosheets on DRH enhances MG degradation to 181 mg g-1 under dark conditions and 550 mg g-1 in the presence of light. Mechanistic insights reveal a synergistic adsorption-cum-degradation phenomenon, amplified by generation of reactive oxygen species during photodegradation which was confirmed from radical scavenging activity. Interestingly, DRH-MoS2 demonstrates potent antibacterial activity against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) with sustained photodegradation efficiency (>80%) over three cycles. The present work reports a cost-effective and scalable strategy for environmental remediation of real wastewater which usually contains both dye pollutants as well as microbes using abundantly available renewable resources such as sunlight and agricultural biomass wastes.

Bismuth oxymetallate-modified biochar derived from Euryale ferox husk for efficient removal of Congo red from wastewater: adsorption behavior and mechanisms

Using Euryale ferox husk as raw material, pristine biochar (EBC), Bi2MoO6-modified biochar (BM-EBC), and BiFeO3-modified biochar (BF-EBC) were prepared and employed for decontaminating Congo red (CR) from wastewater. Compared with EBC (217.59 mg/g) and BF-EBC (359.49 mg/g), a superior adsorption capacity of 460.77 mg/g was achieved by BM-EBC. Based on the evaluation results of the Freundlich and pseudo-second-order models, multilayer chemisorption was suggested as the adsorption mechanism. The adsorption process of BM-EBC was spontaneous and endothermic, and the rate-limiting step pertained to liquid film diffusion and intraparticle diffusion. The underlying removal mechanism was explored via SEM, BET, FTIR, XPS, Raman spectra, and Zeta potential analyses. The introduction of bismuth oxymetallates with their high number of M-O (M: Bi, Mo, Fe) structural elements provided the adsorbent with enlarged surface areas and reinforced oxygen functional groups, thereby promoting pore filling, π-π interactions, hydrogen bonding, and complexation, leading to enhanced adsorption capacity. These results demonstrate that Euryale ferox husk biochar modified by bismuth oxymetallates has high prospects for valorizing biomass waste and removing CR from wastewater.

Mechanistic understanding of green synthesized cerium nanoparticles for the photocatalytic degradation of dyes and antibiotics from aqueous media and antimicrobial efficacy: A review

In recent years, extensive research endeavors are being undertaken for synthesis of an efficient, economic and eco-friendly cerium oxide nanoparticles (CeO2 NPs) using plant extract mediated greener approach. A number of medicinal plants and their specific parts (flowers, bark, seeds, fruits, seeds and leaves) have been found to be capable of synthesizing CeO2 NPs. The specific key phytochemical constituents of plants such as alkaloids, terpenoids, phenolic acids, flavones and tannins can play significant role as a reducing, stabilizing and capping agents in the synthesis of CeO2 NPs from their respective precursor solution of metal ions. The CeO2 NPs are frequently using in diverse fields of science and technology including photocatalytic degradation of dyes, antibiotics as well as antimicrobial applications. In this review, the mechanism behind the green synthesis CeO2 NPs using plant entities are summarized along with discussion of analytical results from characterization techniques. An overview of CeO2 NPs for water remediation application via photocatalytic degradation of dyes and antibiotics are discussed. In addition, the mechanisms of antimicrobial efficacy of CeO2 NPs and current challenges for their sustainable application at large scale in real environmental conditions are discussed.

Petroleum-contaminated soil bioremediation and microbial community succession induced by application of co-pyrolysis biochar amendment: An investigation of performances and mechanisms

This study aimed to remediate petroleum-contaminated soil using co-pyrolysis biochar derived from rice husk and cellulose. Rice husk and cellulose were mixed in various weight ratios (0:1, 1:0, 1:1, 1:3 and 3:1) and pyrolyzed under 500 °C. These biochar variants were labeled as R0C1, R1C0, R1C1, R1C3 and R3C1, respectively. Notably, the specific surface area and carbon content of the co- pyrolysis biochar increased, potentially promoting the growth and colonization of soil microorganisms. On the 60th day, the microbial control group achieved a 46.69% removal of pollutants, while the addition of R0C1, R1C0, R1C3, R1C1 and R3C1 resulted in removals of 70.56%, 67.01%, 67.62%, 68.74% and 67.30%, respectively. In contrast, the highest efficiency observed in the abiotic treatment group was only 24.12%. This suggested that the removal of petroleum pollutants was an outcome of the collaborative influence of co-pyrolysis biochar and soil microorganisms. Furthermore, the abundance of Proteobacteria, renowned for its petroleum degradation capability, obviously increased in the treatment group with the addition of co-pyrolysis biochar. This demonstrated that co-pyrolysis biochar could notably stimulate the growth of functionally associated microorganisms. This research confirmed the promising application of co-pyrolysis biochar in the remediation of petroleum-contaminated soil.

Malachite green (cationic dye) removal with modified Pinus brutia biochar

Dyes are frequently used in industries such as textile, leather, paper and printing, to water sources causes harmful effects on the environment and human health. Therefore, it is crucial to effectively remove colored contaminants from water in order to protect the environment and public health, maintain biodiversity and preserve the esthetic aspects of water resources. In this study, wood chips obtained from Pinus brutia (PB) tree grown in many parts of the world were turned into biochar and then modified and used for the removal of malachite green, a cationic dye. For this purpose, biochar (PBB) was made by collecting PB wood and turning it into chips (PB). Later, PBB was modified to gain nano-magnetic properties. The structure of the obtained PBB and nM-PBB adsorbents was characterized by FT-IR. pH (2-9), temperature (25 °C-55 °C), time change (15 min-240 min), adsorbent amount change (0.05 g-0.45g) and MG concentration (25 mg/L-250 mg/L) were investigated in MG removal of PBB and nM-PBB. The process was found to be pseudo-second-order and spontaneous endothermic reaction. PBB and nM-PBB were found to be suitable for Langmuir isotherm in MG removal (qmax=13.004 mg/g for PBB, qmax=18.215 mg/g for nM-PBB).

From Waste to Resource: Valorization of Lignocellulosic Agri-Food Residues through Engineered Hydrochar and Biochar for Environmental and Clean Energy Applications-A Comprehensive Review

Agri-food residues or by-products have increased their contribution to the global tally of unsustainably generated waste. These residues, characterized by their inherent physicochemical properties and rich in lignocellulosic composition, are progressively being recognized as valuable products that align with the principles of zero waste and circular economy advocated for by different government entities. Consequently, they are utilized as raw materials in other industrial sectors, such as the notable case of environmental remediation. This review highlights the substantial potential of thermochemical valorized agri-food residues, transformed into biochar and hydrochar, as versatile adsorbents in wastewater treatment and as promising alternatives in various environmental and energy-related applications. These materials, with their enhanced properties achieved through tailored engineering techniques, offer competent solutions with cost-effective and satisfactory results in applications in various environmental contexts such as removing pollutants from wastewater or green energy generation. This sustainable approach not only addresses environmental concerns but also paves the way for a more eco-friendly and resource-efficient future, making it an exciting prospect for diverse applications.

Recent advancements and challenges in emerging applications of biochar-based catalysts

The sustainable utilization of biochar produced from biomass waste could substantially promote the development of carbon neutrality and a circular economy. Due to their cost-effectiveness, multiple functionalities, tailorable porous structure, and thermal stability, biochar-based catalysts play a vital role in sustainable biorefineries and environmental protection, contributing to a positive, planet-level impact. This review provides an overview of emerging synthesis routes for multifunctional biochar-based catalysts. It discusses recent advances in biorefinery and pollutant degradation in air, soil, and water, providing deeper and more comprehensive information of the catalysts, such as physicochemical properties and surface chemistry. The catalytic performance and deactivation mechanisms under different catalytic systems were critically reviewed, providing new insights into developing efficient and practical biochar-based catalysts for large-scale use in various applications. Machine learning (ML)-based predictions and inverse design have addressed the innovation of biochar-based catalysts with high-performance applications, as ML efficiently predicts the properties and performance of biochar, interprets the underlying mechanisms and complicated relationships, and guides biochar synthesis. Finally, environmental benefit and economic feasibility assessments are proposed for science-based guidelines for industries and policymakers. With concerted effort, upgrading biomass waste into high-performance catalysts for biorefinery and environmental protection could reduce environmental pollution, increase energy safety, and achieve sustainable biomass management, all of which are beneficial for attaining several of the United Nations Sustainable Development Goals (UN SDGs) and Environmental, Social and Governance (ESG).

Effective removal of malachite green from local dyeing wastewater using zinc-tungstate based materials

The frequent use of an industrial dye such as malachite green (MG) has caused major water body deterioration and is one of the most pressing global challenges, demanding effective treatment techniques. To solve these issues, a simplistic method was developed to synthesize zinc-tungstate (ZnWO4) nanoparticles and also dope the surface matrix of the ZnWO4 nanoparticles using nonmetals of boron (B), carbon (C), and nitrogen (N) at different ratios for enhanced MG removal from wastewater. The prepared nanomaterials were characterized by different methods for crystal structure composition, surface properties, surface morphology, microstructures, functional groups, and elemental oxidation states. The BET analysis revealed a mesoporous structure with surface areas of 30.740 m2/g for ZnWO4, 38.513 m2/g for ZnWO4@BCN, 37.368 m2/g for ZnWO4@BCN/B, 39.325 m2/g for ZnWO4@BCN/C, and 45.436 m2/g for ZnWO4@BCN/N nanocomposites. The best removal of MG was accomplished at pH (8), contact period (50 min), nanoadsorbent dose (0.8 g/L), initial MG concentration (20 mg/L), and temperature (303 K). The maximum adsorption capacities of ZnWO4 and ZnWO4@BCN/N towards MG were 218.645 and 251.758 mg/g, respectively. At equilibrium, the Freundlich isotherm and pseudo-second-order kinetic models were the best fits for the experimental data of MG adsorption on both nanoadsorbents. After eight cycles of adsorption and desorption, both ZnWO4 and ZnWO4@BCN/N were found to be good at removing MG, with efficiencies of 71.00 and 74.20%, respectively. Thermodynamic investigations further validated the spontaneity and endothermic nature of the adsorption process. All study findings confirm the nanoadsorbents exceptional capability and economic feasibility for removing MG dye.

A novel Ce-Ni@biochar nanocomposite with enhanced photocatalytic activity towards organic dyes degradation: impact of process variables and water matrices

The intent of this research work is to implement a biogenic, affordable, and highly effective Ce-Ni@biochar catalyst in order to study its photoactivity in the removal of crystal violet and malachite green oxalate. The catalyst was synthesized using liquid phase reduction method where cerium and nickel nanoparticles are embedded on the rice husk biochar for photocatalytic degradation of organic dyes in the presence of sunshine. Various characterization techniques were conducted on fabricated catalyst for adequate evaluation of the chemical composition as well as morphological and topographical properties of the formed compound. The nanoparticles embedded on biochar persuade increased charge separation that resulted in a substantial decrease in electron-hole recombination rate. The synergistic actions of the catalyst resulted in a high level of photocatalytic activity. The fabricated nanocatalyst showed excellent photoactivity that caused 96 and 99% degradation of crystal violet and malachite green oxalate, a growing industrial pollutant, within 35 and 25 min, respectively. A persuasive mechanism and kinetics are well presented. A series of investigations were done on other factors, such as contact duration, catalyst dosage, starting concentration, interfering ions, and pH, to know its degradation pursuance. The impacts of different water matrices were also investigated. The removal effectiveness of the synthesized catalyst persisted after five consecutive cycles. Marking the burgeoning industrial effluents as a result of rapid industrialization and also focusing on easy availability and low-cost source as well as high efficiency, reusability of the catalyst imparts its novelty and need of this research work.

Removal Performance and Mechanism of Emerging Pollutant Chloroquine Phosphate from Water by Iron and Magnesium Co-Modified Rape Straw Biochar

Chloroquine phosphate (CQP) is effective in treating coronavirus disease 2019 (COVID-19); thus, its usage is rapidly increasing, which may pose a potential hazard to the environment and living organisms. However, there are limited findings on the removal of CQP in water. Herein, iron and magnesium co-modified rape straw biochar (Fe/Mg-RSB) was prepared to remove CQP from the aqueous solution. The results showed that Fe and Mg co-modification enhanced the adsorption efficiency of rape straw biochar (RSB) for CQP with the maximum adsorption capacity of 42.93 mg/g (at 308 K), which was about two times higher than that of RSB. The adsorption kinetics and isotherms analysis, as well as the physicochemical characterization analysis, demonstrated that the adsorption of CQP onto Fe/Mg-RSB was caused by the synergistic effect of pore filling, π-π interaction, hydrogen bonding, surface complexation, and electrostatic interaction. In addition, although solution pH and ionic strength affected the adsorption performance of CQP, Fe/Mg-RSB still had a high adsorption capability for CQP. Column adsorption experiments revealed that the Yoon-Nelson model better described the dynamic adsorption behavior of Fe/Mg-RSB. Furthermore, Fe/Mg-RSB had the potential for repeated use. Therefore, Fe and Mg co-modified biochar could be used for the remediation of CQP from contaminated water.

Review on Rice Husk Biochar as an Adsorbent for Soil and Water Remediation

Rice husk biochar (RHB) is a low-cost and renewable resource that has been found to be highly effective for the remediation of water and soil environments. Its yield, structure, composition, and physicochemical properties can be modified by changing the parameters of the preparation process, such as the heating rate, pyrolysis temperature, and carrier gas flow rate. Additionally, its specific surface area and functional groups can be modified through physical, chemical, and biological means. Compared to biochar from other feedstocks, RHB performs poorly in solutions with coexisting metal, but can be modified for improved adsorption. In contaminated soils, RHB has been found to be effective in adsorbing heavy metals and organic matter, as well as reducing pollutant availability and enhancing crop growth by regulating soil properties and releasing beneficial elements. However, its effectiveness in complex environments remains uncertain, and further research is needed to fully understand its mechanisms and effectiveness in environmental remediation.

Bandgap engineering approach for designing CuO/Mn3O4/CeO2 heterojunction as a novel photocatalyst for AOP-assisted degradation of Malachite green dye

A ternary nanohybrid CuO/Mn₃O₄/CeO₂ was developed in the present work using a co-precipitation-assisted hydrothermal method. The designed photocatalyst's structural, morphology, elemental composition, electronic states of elements, and optical properties were studied using corresponding analytical techniques. Results from PXRD, TEM/HRTEM, XPS, EDAX, and PL showed that the desired nanostructure had formed. Using Tauc's energy band gap plot, it was determined that the nanostructures band gap was ~ 2.44 eV, which showed the band margins of the various moieties, CeO₂, Mn₃O₄, and CuO, had modified. Thus, improved redox conditions led to a substantial decrease in the recombination rate of electron-hole pairs, which was further explained by a PL study in that charge separation plays a key role. Under exposure to visible light irradiation for 60 min, it was revealed that the photocatalyst achieved 98.98% of photodegradation efficiency for malachite green (MG) dye. The process of photodegradation proceeded according to a pseudo-first-order reaction kinetic model with an excellent rate of reaction of 0.07295 min^-1 with R² = 0.99144. The impacts of different reaction variables, inorganic salts, and water matrices were investigated. This research seeks to create a ternary nanohybrid photocatalyst with high photostability, visible spectrum activity, and reusability up to four cycles.

Experimental microwave-assisted air gasification of biomass in fluidized bed reactor

Microwave-assisted heating is an effective heating method for thermochemical conversion of biomass. In this study, experimental syngas production from microwave-assisted air gasification of biomass in a fluidized bed reactor at different gasification temperatures, equivalence ratios and silicon carbide loads, was studied and reported. The results showed that the highest syngas yield (78.2 wt%), higher heating value (6.3 MJ/Nm³) and cold gas efficiency (81.8 %) were obtained at gasification temperature of 900 °C, equivalence ratio of 0.35 and silicon carbide load of 30 g, and the gasification temperature had significant influence on the syngas production. Microwave-assisted heating showed positive effect on tar reduction, i.e., the tar content at 900 °C (2.1 wt%) in this study was even lower than the tar content (3.2 wt%) from catalytic electrical air gasification of rice husk at 950 °C. Generally, the introduction of microwave-assisted heating showed positive effect on biomass gasification.

One-Step Carbonization Synthesis of Magnetic Biochar with 3D Network Structure and Its Application in Organic Pollutant Control

In this study, a magnetic biochar with a unique 3D network structure was synthesized by using a simple and controllable method. In brief, the microbial filamentous fungus Trichoderma reesei was used as a template, and Fe³⁺ was added to the culture process, which resulted in uniform recombination through the bio-assembly property of fungal hyphae. Finally, magnetic biochar (BMFH/Fe₃O₄) was synthesized by controlling different heating conditions in a high temperature process. The adsorption and Fenton-like catalytic performance of BMFH/Fe₃O₄ were investigated by using the synthetic dye malachite green (MG) and the antibiotic tetracycline hydrochloride (TH) as organic pollutant models. The results showed that the adsorption capacity of BMFH/Fe₃O₄ for MG and TH was 158.2 and 171.26 mg/g, respectively, which was higher than that of most biochar adsorbents, and the Fenton-like catalytic degradation effect of organic pollutants was also better than that of most catalysts. This study provides a magnetic biochar with excellent performance, but more importantly, the method used can be effective in further improving the performance of biochar for better control of organic pollutants.

A new type of calcium-rich biochars derived from spent mushroom substrates and their efficient adsorption properties for cationic dyes

Adsorption is commonly accepted as a most promising strategy in dye wastewater treatment, and the widespread use of adsorption emphasizes the need to explore low-cost but excellent adsorbents. Herein, a low-cost adsorbent (calcium-rich biochar) was developed, which was directly pyrolyzed from spent mushroom substate without any modification. This study evaluated the potential application of two calcium-rich biochars (GSBC and LSBC) derived from spent substrates of Ganoderma lucidum and Lentinus edodes, respectively. The effects of pyrolysis temperature on the calcium-rich biochars characteristics and their adsorption mechanism for cationic dyes (Malachite Green oxalate (MG) and Safranine T (ST)) were studied systematically. The increase in pyrolysis temperature from 350 to 750 °C led to an increase in both biochar ash, Ca content, and specific surface area, which made high-temperature biochars (GS750 and LS750) the superior adsorbents for cationic dyes. Batch adsorption results showed LS750 was more efficient to adsorb dyes than GS750 attributed to its higher Ca content and larger specific surface area. According to the Langmuir model, LS750 had high adsorption capacities of 9,388.04 and 3,871.48 mg g⁻¹ for Malachite green and ST, respectively. The adsorption mechanism of dye MG could be attributed to pore filling, hydrogen bonding, electrostatic interaction, ion exchange, and π-π stacking, while ST adsorption mainly involved pore filling, electrostatic interaction, ion exchange, and π-π stacking. Attributed to their excellent adsorption performance, cheap source, and good reusability, biochars obtained from SMSs were very promising in dyeing wastewater treatment.

Antibiotic bioremediation by new generation biochar: Recent updates

The evolving multidrug resistance in microbes with increasing antibiotic pollution is becoming a severe global crisis. Recent developments on antibiotic remediations by biochar are promising. Advancements in biochar engineering enhanced biochar remediation efficiency to another level through developing new interactions and bonding abilities with antibiotic pollutants. Especially chemical/metal-composite modification significantly increased catalysis of biochar. The review's main focus is to underline biochar efficiency for the abatement of emerging antibiotic pollutants. Moreover, to relate feedstock, production conditions, and engineering techniques with biochar properties. Also, modification strategies are reviewed to obtain biochar or their composites before examining improved remediation potential ranging from 20 to 552 mg g^-1 for various antibiotics. Biochar offers different interactions depending on the surface functionalities e.g., π-π stacking, electrostatic, H-bonding, etc. Biochar and related composites have also been reviewed for remarkable properties e.g., photocatalysis, adsorption, and oxidation processes. Furthermore, future research directions and opportunities for biochar research are discussed.

Optimization, Nature, and Mechanism Investigations for the Adsorption of Ciprofloxacin and Malachite Green onto Carbon Nanoparticles Derived from Low-Cost Precursor via a Green Route

The spread of organic pollutants in water spoils the environment, and among the best-known sorbents for removing organic compounds are carbonaceous materials. Sunflower seed waste (SFSW) was employed as a green and low-cost precursor to prepare carbon nanoparticles (CNPs) via pyrolysis, followed by a ball-milling process. The CNPs were treated with a nitric–sulfuric acid mixture (1:1) at 100 °C. The scanning electron microscopy (SEM) showed a particle size range of 38 to 45 nm, and the Brunauer–Emmett–Teller (BET) surface area was 162.9 m2 g−1. The elemental analysis was performed using energy-dispersive X-ray spectroscopy, and the functional groups on the CNPs were examined with Fourier transform infrared spectroscopy. Additionally, an X-ray diffractometer was employed to test the phase crystallinity of the prepared CNPs. The fabricated CNPs were used to adsorb ciprofloxacin (CFXN) and malachite green (MLG) from water. The experimentally obtained adsorption capacities for CFXN and MLG were 103.6 and 182.4 mg g−1, respectively. The kinetic investigation implied that the adsorption of both pollutants fitted the pseudo-first-order model, and the intraparticle diffusion step controlled the process. The equilibrium findings for CFXN and MLG sorption on the CNPs followed the Langmuir and the Fredulich isotherm models, respectively. It was concluded that both pollutants spontaneously adsorbed on the CNPs, with physisorption being the likely mechanism. Additionally, the FTIR analysis of the adsorbed CFXN showed the disappearance of some functional groups, suggesting a chemisorption contribution. The CNPs showed an excellent performance in removing CFXN and MLG from groundwater and seawater samples and possessed consistent efficiency during the recycle–reuse study. The application of CNPs to treat synthetically contaminated natural water samples indicated the complete remediation of polluted water using the ball-mill-fabricated CNPs.

Efficient remediation of antibiotic pollutants from the environment by innovative biochar: current updates and prospects

The increased antibiotic consumption and their improper management led to serious antibiotic pollution and its exposure to the environment develops multidrug resistance in microbes against antibiotics. The entry rate of antibiotics to the environment is much higher than its exclusion; therefore, efficient removal is a high priority to reduce the harmful impact of antibiotics on human health and the environment. Recent developments in cost-effective and efficient biochar preparation are noticeable for their effective removal. Moreover, biochar engineering advancements enhanced biochar remediation performance several folds more than in its pristine forms. Biochar engineering provides several new interactions and bonding abilities with antibiotic pollutants to increase remediation efficiency. Especially heteroatoms-doping significantly increased catalysis of biochar. The main focus of this review is to underline the crucial role of biochar in the abatement of emerging antibiotic pollutants. A detailed analysis of both native and engineered biochar is provided in this article for antibiotic remediation. There has also been discussion of how biochar properties relate to feedstock, production conditions and manufacturing technologies, and engineering techniques. It is possible to produce biochar with different surface functionalities by varying the feedstock or by modifying the pristine biochar with different chemicals and preparing composites. Subsequently, the interaction of biochar with antibiotic pollutants was compared and reviewed. Depending on the surface functionalities of biochar, they offer different types of interactions e.g., π-π stacking, electrostatic, and H-bonding to adsorb on the biochar surface. This review demonstrates how biochar and related composites have optimized for maximum removal performance by regulating key parameters. Furthermore, future research directions and opportunities for biochar research are discussed.

A review on the treatment of dyes in printing and dyeing wastewater by plant biomass carbon

Printing and dyeing wastewater (PDW) has characteristics of large amount of water, elevated content of residual dyes, poor biodegradability, high alkalinity and large change of water quality, making its treatment difficult. Development of efficient and economic PDW treatment technology has gained considerable interest in the field of environmental protection. Use of plant biomass carbon (PBC) for the adsorption of dyes is a feasible and economical technology. This review summarizes current literature discussing the preparation method and physicochemical characteristics of PBC prepared from different plant species, the effect of PBC on the removal of dyes, influencing factors affecting the removal, and relevant adsorption models. The shortcomings of current research and the direction of future research are also pointed out in the review.

Biofiber waste derived zwitterionic and photocatalytic dye adsorbent: Switchable selectivity, in-situ degradation and multi-tasking application

Dye wastewater and discarded biofiber have brought huge pressure to sustainable developments of ecology and economy. By utilizing dopamine chemistry and benzophenone mediated "grafting onto" atom transfer radical polymerization (ATRP), this work reported a biomass adsorbent containing discarded wool substrate, photocatalytic PDA coating and zwitterionic polymer brushes for dyes removal. The grafted zwitterionic polymer brushes impart the material with not only high adsorption capacity and rapid adsorption rate, but also switchable adsorption selectivity and pH-controlled regeneration capability. Benefiting from such outstanding adsorption performance and excellent free-standing property, the adsorbent could fulfill diversified needs of both static and dynamic adsorptions. Under daylight, the constructed photocatalytic PDA coating could in-situ degrade the captured pollutant, thus achieving consecutive adsorption-degradation-regeneration utilization. Furthermore, through simple dip-coating and cleaner UV-irradiation techniques, the preparation process could be scaled up. This work contributes to both the upcycling of discarded biofiber waste and the development of advanced biomass adsorbent.

Chitosan-based nanocomposites for removal of Cr(VI) and synthetic food colorants from wastewater

Current study aims to synthesize chitosan/polyvinyl alcohol (CS/PVA), poly(ethyleneimine), and Fe₃O₄ impregnated beads for co-removal of Cr(VI) and toxic azo-dyes from wastewater. The mesoporous PEI@AC@Fe₃O₄ exhibits magnetism and enhanced physisorption by higher specific-porosity (2.1 nm) from Cr(VI) radii (0.044 nm). Moreover, surface functional groups (-OH, -NH, -NH₂, -COOH etc.), especially amines enhance ionic bonding due to positive zeta potential. Hence, it is unique for anionic dyes removal under a wide pH range. It showed maximum adsorption capacity 98, 85.5, 85.8, and 91%, or 199.8, 148, 167, 176.5 mg g^-1 respectively for Cr(VI), tartrazine, sunset yellow, and erythrosine. Surface adsorption of Cr(VI) and its transition into Cr(III) was confirmed by EDX. Langmuir isotherm and pseudo-first-order kinetics best fit the adsorption of Cr(VI) and azo-dyes confirming their monolayer physisorption on adsorbent surface. Synthesized adsorbent examined in wastewater purification prototype for efficient removal of different simulated wastewaters confirms its potential for real-world applications.