The influence of acidity on microbial fuel cells containing Shewanella oneidensis

Exploring the secondary mineral products generated by microbial iron respiration in Archean ocean simulations

Marine chemical sedimentary deposits known as Banded Iron Formations (BIFs) archive Archean ocean chemistry and, potentially, signs of ancient microbial life. BIFs contain a diversity of iron- and silica-rich minerals in disequilibrium, and thus many interpretations of these phases suggest they formed secondarily during early diagenetic processes. One such hypothesis posits that the early diagenetic microbial respiration of primary iron(III) oxides in BIFs resulted in the formation of other iron phases, including the iron-rich silicates, carbonates, and magnetite common in BIF assemblages. Here, we simulated this proposed pathway in laboratory incubations combining a model dissimilatory iron-reducing (DIR) bacterium, Shewanella putrefaciens CN32, and the ferric oxyhydroxide mineral ferrihydrite under conditions mimicking the predicted Archean seawater geochemistry. We assessed the impact of dissolved silica, calcium, and magnesium on the bioreduced precipitates. After harvesting the solid products from these experiments, we analyzed the reduced mineral phases using Raman spectroscopy, electron microscopy, powder x-ray diffraction, and spectrophotometric techniques to identify mineral precipitates and track the bulk distributions of Fe(II) and Fe(III). These techniques detected a diverse range of calcium carbonate morphologies and polymorphism in incubations with calcium, as well as secondary ferric oxide phases like goethite in silica-free experiments. We also identified aggregates of curling, iron- and silica-rich amorphous precipitates in all incubations amended with silica. Although ferric oxides persist even in our electron acceptor-limited incubations, our observations indicate that microbial iron reduction of ferrihydrite is a viable pathway for the formation of early iron silicate phases. This finding allows us to draw parallels between our experimental proto-silicates and the recently characterized iron silicate nanoinclusions in BIF chert deposits, suggesting that early iron silicates could possibly be signatures of iron-reducing metabolisms on early Earth.

A critical review on early-warning electrochemical system on microbial fuel cell-based biosensor for on-site water quality monitoring

The microbial fuel cell (MFC) sensor is a very promising self-powered self-sustainable system for early warning water quality detection. These sensors are cost-effective, biodegradable, compact in design, and portable in nature are favorable for real-time in situ water quality monitoring. This review represents the mechanism action behind the toxicity detection, optimization strategies, process parameters, role of biofilm, the role of external resistance, hydrodynamic study, and mathematical modeling for improving the performance of the sensor. Additionally, the techno-economic prospect of this MFC-based sensor and its challenges, limitations are addressed to make it economically more favorable for commercial use. The future direction is also explored based on the sensor's disadvantages and limitations. Comprehensively, this review covered all the possible directions of MFC sensor fabrication, their application, recent advancement, prospects challenges, and their possible solutions.

Biocatalyst physiology and interplay: a protagonist of MFC operation

Microbial fuel cells (MFC) have been foreseen as a sustainable renewable energy resource to meet future energy demand. In the past, several studies have been executed in both benchtop and pilot scale to produce electrical energy from wastewater. The key role players in this technology that leads to the operation are microbes, mainly bacteria. The dominant among them is termed as "exoelectrogens" that have the capability to produce and transport electron by utilizing waste source. The current review focuses on such electrogenic bacteria's involvement for enhanced power generation of MFC. The pathway of electron transfer in their cell along and its conduction to the extracellular environment of the MFC system are critically discussed. The interaction of the microbes in various MFC operational conditions, including the role of substrate and solid electron acceptors, i.e., anode, external resistance, temperature, and pH, was also discussed in depth along with biotechnological advancement and future research perspective.

Experimental and validation with neural network time series model of microbial fuel cell bio-sensor for phenol detection

Phenol is one of the most commonly known chemical compound found as a pollutant in the chemical industrial wastewater. This pollutant has potential threat for human health and environment, as it can be easily absorbed by the skin and the mucous. Here, we prepared dual chambered microbial fuel cell (MFC) sensor for the detection of phenol. Varying concentration of phenol (100 mg/l, 250 mg/l, 500 mg/l, and 1000 mg/l) was applied as a substrate to the MFC and their change in output voltage was also measured. After adding 100 mg/l, 250 mg/l, 500 mg/l, and 1000 mg/l of phenol as sole substrate to the MFC, the maximum voltage output was obtained as 360 ± 10 mV, 395 ± 8 mV, 320 ± 7 mV, 350 ± 5 mV respectively. This biosensor was operated using industrial wastewater isolated microbes as a sensing element and phenol was used as a sole substrate. The topologies of ANN were analyzed to get the best model to predict the power output of MFCs and the training algorithms were compared with their convergence rates in training and test results. Time series model was used for regression analysis to predict the future values based on previously observed values. Two types of mathematical modeling i.e. Scaled Conjugate Gradient (SCG) algorithm and Time-series model was used with 44 experimental data with varying phenol concentration and varying synthetic wastewater concentration to optimize the biosensor performance. Both SCG and time series showing the best results with R² value 0.98802 and 0.99115.

Local Acidification Limits the Current Production and Biofilm Formation of Shewanella oneidensis MR-1 With Electrospun Anodes

The anodic current production of Shewanella oneidensis MR-1 is typically lower compared to other electroactive bacteria. The main reason for the low current densities is the poor biofilm growth on most anode materials. We demonstrate that the high current production of Shewanella oneidensis MR-1 with electrospun anodes exhibits a similar threshold current density as dense Geobacter spp biofilms. The threshold current density is a result of local acidification in the biofilm. Increasing buffer concentration from 10 to 40 mM results in a 1.8-fold increase of the current density [(590 ± 25) μA cm⁻²] while biofilm growth stimulation by riboflavin has little effect on the current production. The current production of a reference material below the threshold did not respond to the increased buffer concentration but could be enhanced by supplemented riboflavin that stimulated the biofilm growth. Our results suggest that the current production with S. oneidensis is limited (1) by the biofilm growth on the anode that can be enhanced by the choice of the electrode material, and (2) by the proton transport through the biofilm and the associated local acidification.

A novel application of simple submersible yeast-based microbial fuel cells as dissolved oxygen sensors in environmental waters

In this study, yeast microbial fuel cells (MFCs) were established as biosensors for in-situ monitoring of dissolved oxygen (DO) levels in environmental waters, with yeast and glucose substrates acting as biocatalyst and fuel, respectively. Diverse environmental factors, such as temperature, pH and conductivity, were considered. The sensor performance was first tested with distilled water with different DO levels ranging from 0 mg/L to 8 mg/L and an external resistance of 1000 Ω. The relationship between DO and current density was non-linear (exponential). This MFC capability was further explored under different environmental conditions (pH, temperature and conductivity), and the current density produced was within the range of 0.14-34.88 mA/m², which increased with elevated DO concentration. The resulting regression was y = 1.3051e^0.3548x, with a regression coefficient (R²) = 0.71, indicating that the MFC-based DO meter was susceptible to interference. When used in environmental water samples, DO measurements using MFC resulted in errors ranging from 6.25 % to 15.15 % when compared with commercial DO meters. The simple yeast-based MFC sensors demonstrate promising prospects for future monitoring in a variety of areas, including developing countries and remote locations.

Production of bioelectricity may play an important role for the survival of Xanthomonas campestris pv. campestris (Xcc) under anaerobic conditions

The plant pathogen Xanthomonas is commonly found in biocontaminated bioreactors; however, few studies have evaluated the growth and impacts of this microorganism on bioreactors. In this study, we examined the characteristics of Xanthomonas campestris pv. campestris (Xcc). Our results showed that Xcc could reduce metal Fe (III) and decolorise methyl orange in vitro. Moreover, I-t and cyclic voltammetry curves showed that Xcc could generate bioelectricity and had two extracellular electron transfer pathways, similar to that of Shewanella. Based on the spectral analysis of intact cells and scanning electron microscopy analysis, one pathway was speculated to involve cytochrome C by direct contact with the pili or cell surface. The other pathway may involve indirect mediators, such as redox substrates, among extracellular polymeric substances. For the direct extracellular electron transfer process, the charge transfer coefficient α, electron number n, and the electron transfer rate constant k_s were determined to be 0.49, 2.6, and 2.2 × 10^-3 s^-1, respectively. In the indirect extracellular electron transfer processes, the values of α, n, and k_s were 0.52, 4, and 1.21 s^-1, respectively. Of these two transfer methods, indirect electron transfer is dominant and faster than direct electron transfer. Moreover, after mutation of the dsbD gene, which is important for indirect electron transfer, the electrochemical parameters α, n, and k_s decreased. Our findings reveal a new anaerobic mechanism mediating the survival of Xcc during wastewater treatment, and may help develop new strategies for preventing Xcc growth during wastewater treatment.

Narrow pH tolerance found for a microbial fuel cell treating winery wastewater

AIMS

The use of microbial fuel cells (MFC) to treat winery wastewater is promising; however, an initial acidic pH, fluctuating chemical oxygen demand (COD) levels and a lack of natural buffering in these wastewaters make providing a suitable buffer system at an ideal buffer to COD ratio.

METHODS AND RESULTS

A lab scale MFC was designed, inoculated with anaerobic winery sludge and fed with synthetic winery wastewater. It was observed that at pH 6·5, the MFC performed best, the maximum output voltage was 0·63 ± 0·01 V for 60 ± 3 h, and the COD removal efficiency reached 77 ± 7%. The electrogens were affected by pH much more than the bulk COD degrading organisms. Fluorescent in situ hybridization suggested Betaproteobacteria played a significant role in electron transfer.

CONCLUSIONS

A ratio of 1 mmol l^-1 phosphate buffer to 100 mg l^-1 COD was ideal to maintain a stable pH for MFCs treating synthetic winery wastewater.

SIGNIFICANCE AND IMPACT OF THE STUDY

The results find the narrow pH tolerance for MFCs treating winery wastewater and demonstrate the significance of pH and buffer to COD ratio for steady performance of MFCs.

An overview of anoxygenic phototrophic bacteria and their applications in environmental biotechnology for sustainable Resource recovery

Anoxygenic phototrophic bacteria (APB) are a phylogenetically diverse group of organisms that can harness solar energy for their growth and metabolism. These bacteria vary broadly in terms of their metabolism as well as the composition of their photosynthetic apparatus. Unlike oxygenic phototrophic bacteria such as algae and cyanobacteria, APB can use both organic and inorganic electron donors for light-dependent fixation of carbon dioxide without generating oxygen. Their versatile metabolism, ability to adapt in extreme conditions, low maintenance cost and high biomass yield make APB ideal for wastewater treatment, resource recovery and in the production of high value substances. This review highlights the advantages of APB over algae and cyanobacteria, and their applications in photo-bioelectrochemical systems, production of poly-β-hydroxyalkanoates, single-cell protein, biofertilizers and pigments. The ecology of ABP, their distinguishing factors, various physiochemical parameters governing the production of high-value substances and future directions of APB utilization are also discussed.

Electrogenic Biofilm Development Determines Charge Accumulation and Resistance to pH Perturbation

The electrogenic biofilm and the bio-electrode interface are the key biocatalytic components in bioelectrochemical systems (BES) and can have a large impact on cell performance. This study used four different anodic carbons to investigate electrogenic biofilm development to determine the influence of charge accumulation and biofilm growth on system performance and how biofilm structure may mitigate against pH perturbations. Power production was highest (1.40 W/m3) using carbon felt, but significant power was also produced when felt carbon was open-circuit acclimated in a control reactor (0.95 W/m3). The influence of carbon material on electrogenic biofilm development was determined by measuring the level of biofilm growth, using sequencing to identify the microbial populations and confocal microscopy to understand the spatial locations of key microbial groups. Geobacter spp. were found to be enriched in closed-circuit operation and these were in close association with the carbon anode, but these were not observed in the open-circuit controls. Electrochemical analysis also demonstrated that the highest mid-point anode potentials were close to values reported for cytochromes from Geobacter sulfurreductans. Biofilm development was greatest in felt anodes (closed-circuit acclimated 1209 ng/μL DNA), and this facilitated the highest pseudo-capacitive values due to the presence of redox-active species, and this was associated with higher levels of power production and also served to mitigate against the effects of low-pH operation. Supporting carbon anode structures are key to electrogenic biofilm development and associated system performance and are also capable of protecting electrochemically active bacteria from the effects of environmental perturbations.

Microbial fuel cell-based biosensor for online monitoring wastewater quality: A critical review

Recently, the application of the microbial fuel cell (MFC)-based biosensor for rapid and real-time monitoring wastewater quality is very innovative due to its simple compact design, disposability, and cost-effectiveness. This review represents recent advances in this emerging technology for the management of wastewater quality, where the emphasis is on biochemical oxygen demand, toxicity, and other environmental applications. In addition, the main challenges of this technology are discussed, followed by proposing possible solutions to those challenges based on the existing knowledge of detection principles and signal processing. Potential future research of MFC-based biosensor has been demonstrated in this review.

Investigating effect of proton-exchange membrane on new air-cathode single-chamber microbial fuel cell configuration for bioenergy recovery from Azorubine dye degradation

One of the biggest challenges of using single-chamber microbial fuel cells (MFCs) that utilize proton-exchange membrane (PEM) air cathode for bioenergy recovery from recalcitrant organic compounds present in wastewater is mainly attributed to their high internal resistance in the anodic chamber of the single microbial fuel cell (MFC) configurations. The high internal resistance is due to the small surface area of the anode and cathode electrodes following membrane biofouling and pH splitting conditions as well as substrate and oxygen crossover through the membrane pores by diffusion. To address this issue, the fabrication of new PEM air-cathode single-chamber MFC configuration was investigated with inner channel flow open assembled with double PEM air cathodes (two oxygen reduction activity zones) coupled with spiral-anode MFC (2MA-CsS-AMFC). The effect of various proton-exchange membranes (PEMs), including Nafion 117 (N-117), Nafion 115 (N-115), and Nafion 212 (N-212) with respective thicknesses of 183, 127, and 50.08 μ, was separately incorporated into carbon cloth as PEM air-cathode electrode to evaluate their influences on the performance of the 2MA-CsS-AMFC configuration operated in fed-batch mode, while Azorubine dye was selected as the recalcitrant organic compound. The fed-batch test results showed that the 2MA-CsS-AMFC configuration with PEM N-115 operated at Azorubine dye concentration of 300 mg L^-1 produced the highest power density of 1022.5 mW m^-2 and open-circuit voltage (OCV) of 1.20 V coupled with enhanced dye removal (4.77 mg L h^-1) compared to 2MA-CsS-AMFCs with PEMs N-117 and N-212 and those in previously published data. Interestingly, PEM 115 showed remarkable reduction in biofouling and pH splitting. Apart from that, mass transfer coefficient of PEM N-117 was the most permeable to oxygen (K_O = 1.72 × 10^-4 cm s^-1) and PEM N-212 was the most permeable membrane to Azorubine (K_A = 7.52 × 10^-8 cm s^-1), while PEM N-115 was the least permeable to both oxygen (K_O = 1.54 × 10^-4) and Azorubine (K_A = 7.70 × 10^-10). The results demonstrated that the 2MA-CsS-AMFC could be promising configuration for bioenergy recovery from wastewater treatment under various PEMs, while application of PEM N-115 produced the best performance compared to PEMs N-212 and N-117 and those in previous studies of membrane/membrane-less air-cathode single-chamber MFCs that consumed dye wastewater.

Removal of petroleum hydrocarbons and sulfates from produced water using different bioelectrochemical reactor configurations

Produced water (PW) is a wastewater generated in large quantities from the extraction of oil and gas. PW found to have high amounts of dissolved solids (TDS) and residual petroleum hydrocarbons causing considerable damage to the environment. PW also contains sulfates in significant amounts, due to which treating this wastewater is essential prior to discharge. The present study was aimed for bioelectrochemical treatment of PW and simultaneous bioelectrogenesis in the two most studied configurations viz., single and dual chamber microbial fuel cells (MFCs). The study evidenced treatment of recalcitrant pollutants of PW. Both MFCs were operated by keeping similar operating conditions such as anode chamber volume, hydraulic retention time (HRT) for batch mode of operation, electrode materials, inlet characteristics of PW and ambient temperature. Among both configurations, dual chamber MFC showed higher efficiency with respect to bioelectrogenesis (single chamber - 789 mW/m²; dual chamber - 1089 mW/m²), sulfates removal (single chamber - 79.6%; dual chamber - 93.9%), total petroleum hydrocarbons removal (TPH, single chamber - 47.6%; dual chamber - 53.1%) and chemical oxygen demand degradation (COD, single chamber - 0.30 kg COD/m³-day (COD removal efficiency, 54.7%); dual chamber - 0.33 kg COD/m³-day (COD removal efficiency, 60.2%)). Evaluated polarization behavior of both MFCs were also evidenced the effective response of the electroactive anodic biofilm.

Novel Applications of Microbial Fuel Cells in Sensors and Biosensors

A microbial fuel cell (MFC) is a type of bio-electrochemical system with novel features, such as electricity generation, wastewater treatment, and biosensor applications. In recent years, progressive trends in MFC research on its chemical, electrochemical, and microbiological aspects has resulted in its noticeable applications in the field of sensing. This review was consequently aimed to provide an overview of the most interesting new applications of MFCs in sensors, such as providing the required electrical current and power for remote sensors (energy supply device for sensors) and detection of pollutants, biochemical oxygen demand (BOD), and specific DNA strands by MFCs without an external analytical device (self-powered biosensors). Moreover, in this review, procedures of MFC operation as a power supply for pH, temperature, and organic loading rate (OLR) sensors, and also self-powered biosensors of toxicity, pollutants, and BOD have been discussed.

Using metabolic charge production in the tricarboxylic acid cycle (QTCA) to evaluate the extracellular-electron-transfer performances of Shewanella spp

Using an electrochemical cell equipped with carbon felt electrodes (poised at +0.63 V vs. SHE), the current production capabilities of two Shewanella strains-NTOU1 and KR-12-were examined under various conditions with lactate as an electron donor. The metabolic charge produced in the tricarboxylic acid cycle (Q_TCA) was calculated by mass-balance. The data showed a linear relation between the electric coulomb production (Q_EL) and Q_TCA with an R² of 0.65. In addition, a large amount of pyruvate accumulation was observed at pH = 6, rendering Q_TCA negative. The results indicate an occurrence of an undesired cataplerotic reaction. It was also found that Q_TCA provides important information showing the oxygen-boosting TCA cycle and anodic-current generation of Shewanella spp. Linear dependence of the change in charge for biomass growth (4.52FΔn_Cell) on Q_TCA was also found as expressed by 4.52FΔn_Cell = 1.0428 Q_TCA + 0.0442, indicating that these two charge quantities are inherently identical under most of the experimental conditions. In the mediator-spiked experiments, the external addition of the mediators (ferricyanide, anthraquinone-2, 6-disulfonate, and riboflavin) beyond certain concentrations inhibited the activity of the TCA cycle, indicating that the oxidative phosphorylation is deactivated by excessive amounts of mediators, yet Shewanella spp. are constrained with regard to carrying out the substrate-level phosphorylation.

Microbial fuel cells as an alternative energy source: current status

Microbial fuel cell (MFC) technology is an emerging area for alternative renewable energy generation and it offers additional opportunities for environmental bioremediation. Recent scientific studies have focused on MFC reactor design as well as reactor operations to increase energy output. The advancement in alternative MFC models and their performance in recent years reflect the interests of scientific community to exploit this technology for wider practical applications and environmental benefit. This is reflected in the diversity of the substrates available for use in MFCs at an economically viable level. This review provides an overview of the commonly used MFC designs and materials along with the basic operating parameters that have been developed in recent years. Still, many limitations and challenges exist for MFC development that needs to be further addressed to make them economically feasible for general use. These include continued improvements in fuel cell design and efficiency as well scale-up with economically practical applications tailored to local needs.

Microbial diversity structure in acetate single chamber microbial fuel cell for electricity generation

This study investigates the performance of acetate feed membrane less single chamber microbial fuel cell and physical characterization of the bio film present on the anode surface using Scanning Electron Microscope (SEM) and 16S rRNA analyzer. The performance has been investigated using Teflon treated carbon paper with 0.3 mg/cm2 Pt/C loaded as a cathode and carbon paper as an anode. The maximum open circuit potential is noticed as 791 mV, the system successfully revealed a maximum power density of 86.1 mW m-2 at stable current density of 354 mA m-2 with high coulombic efficiency of 65% at maximum degradation rate of 96%. SEM showed the dense adherence of microorganisms on the anode. 16S rRNA sequencing results indicates phylogenetic mixture in the communities of anodic biofilm and there is no single dominant bacterial species. The dominant phyla are Firmicutes, Gamma Proteobacteria, Alpha Proteobacteria, Actinobacteria, with ten dominant microbial strains: Bacillus firmus, Shewanella profunda, Bacillus isronensis, Brevundimonas bullata, Pseudomonas putida, Planococcus citreus, Micrococcus endophyticus, Acinetobacter tandoii, Bacillus safensis and Shewanella xiamenensis.

Arsenic treatment and power generation with a dual-chambered fuel cell with anionic and cationic membranes using NaHCO3 anolyte and HCl or NaCl catholyte

Dual-chambered fuel cells with an iron anode and an air-carbon cathode separated by an ion exchange membranes have been used to treat arsenate during power production. To select an effective catholyte, the dual-chambered fuel cell consisted 90 mL of 0.1 M HCl or 0.5 M NaCl as the catholyte and 1 L of 0.1 M NaHCO₃ as the anolyte at an initial pH 5. The 0.1 M HCl was an effective catholyte, with which 1 ppm arsenate in 1 L of anolyte was reduced to 5 ppb in 1 h, and the maximum power density was about 6.3 w/m² with an anion exchange membrane fuel cell (AEM_FC) and 4.4 w/m² with a cation exchange membrane fuel cell (CEM_FC). Therefore, 90 mL of 0.1 M HCl was used as a catholyte to treat 20 L of 0.1 M NaHCO₃ anolyte containing 1 ppm arsenate at an initial pH of 5 or 7. The arsenate level at pH 5 decreased to less than 5 ppb in 4 h, and the maximum power density was 5.9 W/m² and 4.7 W/m² with AEM_FC and CEM_FC, respectively. When using 0.01 M NaHCO₃ as the anolyte at pH 5, arsenate was reduced to less than 5 ppb in 8 and 24 h for AEC_FC and CEM_FC, respectively. However, when using an anolyte at pH 7, arsenate could not be effectively removed in 24 h. Therefore, when using carbonate as an anolyte, the solution should be adjusted to a weakly acidic pH in order to remove arsenate.

Increasing the recovery of heavy metal ions using two microbial fuel cells operating in parallel with no power output

The present study aimed to improve the performance of microbial fuel cells (MFCs) by using an intermittent connection period without power output. Connecting two MFCs in parallel improved the voltage output of both MFCs until the voltage stabilized. Electric energy was accumulated in two MFCs containing heavy metal ions copper, zinc, and cadmium as electron acceptors by connection in parallel for several hours. The system was then switched to discharge mode with single MFCs with a 1000-Ω resistor connected between anode and cathode. This method successfully achieved highly efficient removal of heavy metal ions. Even when the anolyte was run in sequencing batch mode, the insufficient voltage and power needed to recover heavy metals from the cathode of MFCs can be complemented by the developed method. The average removal ratio of heavy metal ions in sequencing batch mode was 67 % after 10 h. When the discharge time was 20 h, the removal ratios of zinc, copper, and cadmium were 91.5, 86.7, and 83.57 %, respectively; the average removal ratio of these ions after 20 h was only 52.1 % for the control group. Therefore, the average removal efficiency of heavy metal ions increased by 1.75 times using the electrons stored from the bacteria under the open-circuit conditions in parallel mode. Electrochemical impedance data showed that the anode had lower solution resistance and polarization resistance in the parallel stage than as a single MFC, and capacitance increased with the length of time in parallel.

Challenges and recommendations for using membranes in wastewater-based microbial fuel cells for in situ Fenton oxidation for textile wastewater treatment

Wastewater-based microbial fuel cell is a promising green technology that can potentially be used to treat recalcitrant wastewater such as textile wastewater through

An efficient approach to cathode operational parameters optimization for microbial fuel cell using response surface methodology

BACKGROUND

In the recent study, optimum operational conditions of cathode compartment of microbial fuel cell were determined by using Response Surface Methodology (RSM) with a central composite design to maximize power density and COD removal.

METHODS

The interactive effects of parameters such as, pH, buffer concentration and ionic strength on power density and COD removal were evaluated in two-chamber microbial batch-mode fuel cell.

RESULTS

Power density and COD removal for optimal conditions (pH of 6.75, buffer concentration of 0.177 M and ionic strength of cathode chamber of 4.69 mM) improve by 17 and 5%, respectively, in comparison with normal conditions (pH of 7, buffer concentration of 0.1 M and ionic strength of 2.5 mM).

CONCLUSIONS

In conclusion, results verify that response surface methodology could successfully determine cathode chamber optimum operational conditions.

Increase of riboflavin biosynthesis underlies enhancement of extracellular electron transfer of Shewanella in alkaline microbial fuel cells

Electrolyte pH tremendously affects the electricity output of microbial fuel cells. However, its underlying molecular mechanism remains elusive, in particular for Shewanella oneidensis MR-1, one of the most widely adopted electrogenic microorganisms. Herein, we found that MFCs were able to deliver a significant (but different) electricity output in a wide range of pH (from 6 to 10), with the maximum at pH=9 (alkaline), which delivers ∼1.5times' higher power output than that at pH=7 (neutral). Furthermore, cyclic voltammetry analysis showed an enhanced electrochemical activity of riboflavin (responsible for extracellular electron transfer of Shewanella) at alkaline pH. Strikingly, the concentration of riboflavin synthesized by Shewanella in MFCs at different pH showed a good correlation with the electricity output of MFCs. Thus, our results substantiated that the increase of riboflavin biosynthesis by Shewanella at the alkaline condition underlies the improvement of the electricity output in MFCs.

Active energy harvesting from microbial fuel cells at the maximum power point without using resistors

Microbial fuel cell (MFC) technology offers a sustainable approach to harvest electricity from biodegradable materials. Energy production from MFCs has been demonstrated using external resistors or charge pumps, but such methods can only dissipate energy through heat or receive electrons passively from the MFC without any controllability. This study developed a new approach and system that can actively extract energy from MFC reactors at any operating point without using any resistors, especially at the peak power point to maximize energy production. Results show that power harvesting from a recirculating-flow MFC can be well maintained by the maximum power point circuit (MPPC) at its peak power point, while a charge pump was not able to change operating point due to current limitation. Within 18-h test, the energy gained from the MPPC was 76.8 J, 76 times higher than the charge pump (1.0 J) that was commonly used in MFC studies. Both conditions resulted in similar organic removal, but the Coulombic efficiency obtained from the MPPC was 21 times higher than that of the charge pump. Different numbers of capacitors could be used in the MPPC for various energy storage requirements and power supply, and the energy conversion efficiency of the MPPC was further characterized to identify key factors for system improvement. This active energy harvesting approach provides a new perspective for energy harvesting that can maximize MFC energy generation and system controllability.

Mixotrophic operation of photo-bioelectrocatalytic fuel cell under anoxygenic microenvironment enhances the light dependent bioelectrogenic activity

Electrogenic activity of photo-bioelectrocatalytic /photo-biological fuel cell (PhFC) was evaluated in a mixotrophic mode under anoxygenic microenvironment using photosynthetic consortia as biocatalyst. An acetate rich wastewater was used as anolyte for harnessing energy along with additional treatment. Mixotrophic operation facilitated good electrogenic activity and wastewater treatment associated with biomass growth. PhFC operation documented feasible microenvironment for the growth of photosynthetic bacteria compared to algae which was supported by pigment (total chlorophyll and bacteriochlorophyll) and diversity analysis. Pigment data also illustrated the association between bacterial and algal species. The synergistic interaction between anoxygenic and oxygenic photosynthesis was found to be suitable for PhFC operation. Light dependent deposition of electrons at electrode was relatively higher compared to dark dependent electron deposition under anoxygenic condition. PhFC documented for good volatile fatty acids removal by utilizing them as electron donor. Bioelectrochemical behavior of PhFC was evaluated by voltammetric and chronoamperometry analysis.

Comparative bioelectricity production from various wastewaters in microbial fuel cells using mixed cultures and a pure strain of Shewanella oneidensis

Current and power density from four wastewaters, agriculture (AWW), domestic (DWW), paper (PWW), and food/dairy (FDWW), were comparatively evaluated in combination with three inocula: wastewater endogenous microbes (MFC1), Shewanella oneidensis MR-1 (MFC2), and wastewater endogenous microbes with MR-1 (MFC3) in single chamber microbial fuel cells (MFC). Using AWW (0.011 mA/cm(2); 0.0013 mW/cm(2)) and DWW (0.017 mA/cm(2); 0.0036 mW/cm(2)), MFC2 was the best candidate providing the maximum current, whereas AWW-MFC1 and DWW-MFC1 were unable to construct a well-established MFC. FDWW produced a maximum current from MFC3 (0.037 mA/cm(2); 0.015 mW/cm(2)), and confirmed the unsuitability of MFC2 at an alkaline pH. FDWW-MFC3 also performed best with the highest substrate degradation and coulombic efficiency. Mixed culture in MFC3 resulted in higher current generation under the influence of MR-1 (except in PWW), indicating the endogenous microbes were not solely responsible for the current but the outperformance was significantly attributed to the association of MR-1.

Impedance characteristics and polarization behavior of a microbial fuel cell in response to short-term changes in medium pH

pH oppositely influences anode and cathode performance in microbial fuel cells. The differential electrochemical effects at each electrode and the resultant full-cell performance were analyzed in medium pH from 6.0 to 8.0. Potentials changed -60 mV/pH for the anode and -68 mV/pH for the cathode, coincident with thermodynamic estimations. Open circuit voltage reached a maximum (741 mV) at pH 7, and maximum power density was highest (712 mW/m²) at pH 6.5 as the cathode performance improved at lower pH. Maximum current density increased and apparent half-saturation potential (E(KA)) decreased with increasing medium pH due to improved anode performance. An equivalent circuit model composed of two time constant processes accurately fit bioanode impedance data. One of these processes was consistently the rate-limiting step for acetate-oxidizing exoelectrogenesis, with its pH-varying charge transfer resistance R₂ ranging from 2- to 321-fold higher than the pH-independent charge transfer resistance R₁. The associated capacitance C₂ was 2-3 orders of magnitude larger than C₁. R₂ was lowest near E(KA) and increased by several orders of magnitude at anode potentials above E(KA), while R₁ was nearly stable. However, fits deviated slightly at potentials above E(KA) due to emerging impedance possibly associated with diffusion and excessive potential.

Electroactive mixed culture derived biofilms in microbial bioelectrochemical systems: the role of pH on biofilm formation, performance and composition

The pH-value played a crucial role for the development and current production of anodic microbial electroactive biofilms. It was demonstrated that only a narrow pH-window, ranging from pH 6 to 9, was suitable for growth and operation of biofilms derived from pH-neutral wastewater. Any stronger deviation from pH neutral conditions led to a substantial decrease in the biofilm performance. Thus, average current densities of 151, 821 and 730 μA cm(-2) were measured for anode biofilms grown and operated at pH 6, 7 and 9 respectively. The microbial diversity of the anode chamber community during the biofilm selection process was studied using the low cost method flow-cytometry. Thereby, it was demonstrated that the pH value as well as the microbial inocula had an impact on the resulting anode community structure. As shown by cyclic voltammetry the electron transfer thermodynamics of the biofilms was strongly depending on the solution's pH-value.

Solid phase microbial fuel cell (SMFC) for harnessing bioelectricity from composite food waste fermentation: influence of electrode assembly and buffering capacity

Solid phase microbial fuel cells (SMFC; graphite electrodes; open-air cathode) were designed to evaluate the potential of bioelectricity production by stabilizing composite canteen based food waste. The performance was evaluated with three variable electrode-membrane assemblies. Experimental data depicted feasibility of bioelectricity generation from solid state fermentation of food waste. Distance between the electrodes and presence of proton exchange membrane (PEM) showed significant influence on the power yields. SMFC-B (anode placed 5 cm from cathode-PEM) depicted good power output (463 mV; 170.81 mW/m(2)) followed by SMFC-C (anode placed 5 cm from cathode; without PEM; 398 mV; 53.41 mW/m(2)). SMFC-A (PEM sandwiched between electrodes) recorded lowest performance (258 mV; 41.8 mW/m(2)). Sodium carbonate amendment documented marked improvement in power yields due to improvement in the system buffering capacity. SMFCs operation also documented good substrate degradation (COD, 76%) along with bio-ethanol production. The operation of SMFC mimicked solid-sate fermentation which might lead to sustainable solid waste management practices.

The utility of Shewanella japonica for microbial fuel cells

Shewanella-containing microbial fuel cells (MFCs) typically use the fresh water wild-type strain Shewanella oneidensis MR-1 due to its metabolic diversity and facultative oxidant tolerance. However, S. oneidensis MR-1 is not capable of metabolizing polysaccharides for extracellular electron transfer. The applicability of Shewanella japonica (an agar-lytic Shewanella strain) for power applications was analyzed using a diverse array of carbon sources for current generation from MFCs, cellular physiological responses at an electrode surface, biofilm formation, and the presence of soluble extracellular mediators for electron transfer to carbon electrodes. Critically, air-exposed S. japonica utilizes biosynthesized extracellular mediators for electron transfer to carbon electrodes with sucrose as the sole carbon source.

Shewanella knowledgebase: integration of the experimental data and computational predictions suggests a biological role for transcription of intergenic regions

Shewanellae are facultative γ-proteobacteria whose remarkable respiratory versatility has resulted in interest in their utility for bioremediation of heavy metals and radionuclides and for energy generation in microbial fuel cells. Extensive experimental efforts over the last several years and the availability of 21 sequenced Shewanella genomes made it possible to collect and integrate a wealth of information on the genus into one public resource providing new avenues for making biological discoveries and for developing a system level understanding of the cellular processes. The Shewanella knowledgebase was established in 2005 to provide a framework for integrated genome-based studies on Shewanella ecophysiology. The present version of the knowledgebase provides access to a diverse set of experimental and genomic data along with tools for curation of genome annotations and visualization and integration of genomic data with experimental data. As a demonstration of the utility of this resource, we examined a single microarray data set from Shewanella oneidensis MR-1 for new insights into regulatory processes. The integrated analysis of the data predicted a new type of bacterial transcriptional regulation involving co-transcription of the intergenic region with the downstream gene and suggested a biological role for co-transcription that likely prevents the binding of a regulator of the upstream gene to the regulator binding site located in the intergenic region.

Database URL:http://shewanella-knowledgebase.org:8080/Shewanella/ or http://spruce.ornl.gov:8080/Shewanella/