Biosorption of precious metals

Sulfur-containing cellulose esters for selectively anchoring gold for water catalytic decontamination

The facile preparation of sustainable sulfur-containing polymer functional materials has been obtained great attention due to their chemical reactivity and metal complexing ability. In this study, taking the solution properties advantages of the newly developed cellulose solvent system of DBU/DMSO/CO2, thiol and disulfide bond functionalized cellulose ester (TDSCE) was facilely prepared via in-situ tandem transesterification and oxidation reaction by using methyl 3-mercaptopropionate, without adding any external catalyst. The synthetic protocol was featured by that the DBU not only acted as reagent for the dissolution of cellulose, but also catalysts for the transesterification of cellulose with methyl 3-mercaptopropionate to yield cellulose 3-mercaptopropionate (Cell-MP) with maximum degrees of substitution (DS) of 0.77, and an oxidant for the partial oxidation of Cell-MP to produce a cellulose methyl 3,3'-disulfanediyldipropionate (Cell-MDSP) with maximum DS of 0.36 mixed ester, respectively. With successful introduction of thiol and disulfide bond into the cellulose backbone, the TDSCEs indicated desirable selective absorption of Au3+ from mimic heavy mental ions waste water due to the sulfur-Au chemistry with maximal adsorption capacity for Au3+ of 415.2 mg/g. The subsequent reduction of Au3+ into gold nanoparticles (Au NPs) fabricated a robust TDSCE-2@Au NPs composite catalyst with high catalytic activity for the hydrogenation treatment of water pollutes, such as 4-nitrophenol (4-NP)and azo dyes.

Precious Metal Recovery from Wastewater Using Bio-Based Techniques

The recovery of metals from waste material has been on the increase in the past few years due to a number of reasons such as supporting the diversification of metal supply resources. In addition, the alternative use of the waste material for metal recovery can add to the main production line, boosting production throughput and profitability thus, allowing companies to sustain their activities during times of low commodity prices. While there has been a lot of research and interest in the recovery of precious metals such as platinum group metals (PGMs), Au, and Ag from solid waste material, there has been limited focus on the recovery of these value metals from wastewater. This is mostly related to challenges associated with finding cost-effective technologies that can recover these metals from solutions of low metal concentrations. In recent years, bio-based technologies have, however, become established as potential alternatives to traditional techniques in the treatment of wastewater due to their ability to recover metals from solutions of low concentrations. While wastewater might be characterized by some significant value metal content, it also contains other components that have potential economic value if recovered or converted to by-products. Such an approach may not only provide an opportunity for extraction of metal resources from wastewater but also contributes toward the circular economy. This chapter presents insights into precious metal recovery from wastewater using bio-based technologies, compares such an approach to the traditional techniques, explores the recovery of other value-added products and finally considers some of the challenges associated with the large-scale application of the bio-based technologies.

Assessment of Iron Biosorption Potential by Live and Dead Biomass of Bacillus subtilis (MN093305) from Aqueous Solution

Heavy metals polluted aquatic ecosystems and become a global environmental issue due to their toxic effect on all forms of ecosystems and further on all forms of life. Heavy metals are non- degradable and accumulated in different life forms by accumulating in the food chain; this increases the need for the development of a sustainable method for the removal of these metals. Biosorption is an eco-friendly and cost-effective convenient technique of heavy metal bioremediation from the contaminated aquatic ecosystem. The current investigation involves biosorption of iron using Bacillus subtilis strain (MN093305) isolated from Ganga river at different physical parameters with the highest rate of biosorption was 96.64%, 98.91%, 97.88%, and 99.44% at pH 5, 60 min incubation period, 35 °C temperature and 2.5 mg/ml of biomass respectively for dead biomass. Living biomass biosorption rate was 87.32%, 96.74%, 96.94% and 95.02% at pH 7, 72 h, 35 °C and 2.5 mg/ml respectively. Functional groups involved in the biosorption of iron by Bacillus subtilis were fitted to a second-order kinetic model. Langmuir and Freundlich's isotherm are used to evaluate data; both isotherms indicate iron absorption as a favorable process.

3D-Printed Porous Supramolecular Sorbents for Cobalt Recycling

Electronic waste recycling is a recognized global challenge that requires new strategies to bind and release critical materials selectively, such as cobalt present in lithium-ion batteries. To address this challenge, hierarchical 3D-printed porous polymer scaffolds bearing supramolecular receptors were prepared using vat photopolymerization and their cobalt binding profiles were examined as a function of matrix polarity. By combining high-resolution digital light processing (DLP) with polymerization-induced phase separation (PIPS), functional acrylic copolymer networks with micrometer-level precision of geometry and nanometer-level pores were generated. Covalent integration of a methacrylate-functionalized bisdicyclohexyl acetamide (BDCA-MA) receptor enabled binding and release of cobalt(II) chloride (CoCl2) via a solvent polarity switch mechanism involving a change in solvent from ethanol to water. The present structures proved reusable as shown by sustained high binding efficiency over five bind and release cycles. This platform represents a "green" and energy conscious method for future electronic waste recycling.

Comprehensive Investigation of Cu2+ Adsorption from Wastewater Using Olive-Waste-Derived Adsorbents: Experimental and Molecular Insights

This study investigates the efficacy of adsorbents from locally sourced olive waste-encompassing olive skins, leaves, and pits, recovered from the initial centrifugation of olives (OWP)-and a composite with sodium alginate (OWPSA) for the removal of Cu2+ ions from synthetic wastewater. Experimental analyses conducted at room temperature, with an initial Cu2+ concentration of 50 mg/L and a solid/liquid ratio of 1 g/L, showed that the removal efficiencies were approximately 79.54% and 94.54% for OWP and OWPSA, respectively, highlighting the positive impact of alginate on adsorption capacity. Utilizing statistical physics isotherm models, particularly the single-layer model coupled to real gas (SLMRG), allowed us to robustly fit the experimental data, providing insights into the adsorption mechanisms. Thermodynamic parameters affirmed the spontaneity and endothermic nature of the processes. Adsorption kinetics were interpreted effectively using the pseudo-second-order (PSO) model. Molecular modeling investigations, including the conductor-like screening model for real solvents (COSMO-RS), density functional theory (DFT), and atom-in-molecule (AIM) analysis, unveiled intricate molecular interactions among the adsorbent components-cellulose, hemicellulose, lignin, and alginate-and the pollutant Cu2+, confirming their physically interactive nature. These findings emphasize the synergistic application of experimental and theoretical approaches, providing a comprehensive understanding of copper adsorption dynamics at the molecular level. This methodology holds promise for unraveling intricate processes across various adsorbent materials in wastewater treatment applications.

Sustainable Tannin Gels for the Efficient Removal of Metal Ions and Organic Dyes

The usage of a highly efficient, low-cost, and sustainable adsorbent material as an industrial wastewater treatment technique is required. Herein, the usage of the novel, fully sustainable tannin-5-(hydroxymethyl)furfural (TH) aerogels, generated via a water-based sol-gel process, as compatible biosorbent materials is presented. In particular, this study focusses on the surface modification of the tannin biosorbent with carboxyl or amino functional groups, which, hence, alters the accessible adsorption sites, resulting in increased adsorption capacity, as well as investigating the optimal pH conditions for the adsorption process. Precisely, highest adsorption capacities are acquired for the metal cations and cationic dye in an alkaline aqueous environment using a carboxyl-functionalized tannin biosorbent, whereas the anionic dye requires an acidic environment using an amino-functionalized tannin biosorbent. Under these determined optimal conditions, the maximum monolayer adsorption capacity of the tannin biosorbent ensues in the following order: Cu2+ > RB > Zn2+ > MO, with 500, 244, 192, 131 mg g-1, respectively, indicating comparable or even superior adsorption capacities compared to conventional activated carbons or silica adsorbents. Thus, these functionalized, fully sustainable, inexpensive tannin biosorbent materials, that feature high porosity and high specific surface areas, are ideal industrial candidates for the versatile adsorption process from contaminated (heavy) metal or dye solutions.

Copper biosorption by Bacillus pumilus OQ931870 and Bacillus subtilis OQ931871 isolated from Wadi Nakheil, Red Sea, Egypt

BACKGROUND

Despite being necessary, copper is a toxic heavy metal that, at high concentrations, harms the life system. The parameters that affect the bioreduction and biosorption of copper are highly copper-resistant bacteria.

RESULTS

In this work, the ability of the bacterial biomass, isolated from black shale, Wadi Nakheil, Red Sea, Egypt, for Cu2+ attachment, was investigated. Two Cu2+ resistance Bacillus species were isolated; Bacillus pumilus OQ931870 and Bacillus subtilis OQ931871. The most tolerant bacterial isolate to Cu2+ was B. pumilus. Different factors on Cu2+ biosorption were analyzed to estimate the maximum conditions for Cu biosorption. The qmax for Cu2+ by B. pumilus and B. subtilis determined from the Langmuir adsorption isotherm was 11.876 and 19.88 mg. g-1, respectively. According to r2, the biosorption equilibrium isotherms close-fitting with Langmuir and Freundlich model isotherm. Temkin isotherm fitted better to the equilibrium data of B. pumilus and B. subtilis adsorption. Additionally, the Dubinin-Radushkevich (D-R) isotherm suggested that adsorption mechanism of Cu2+ is predominately physisorption.

CONCLUSION

Therefore, the present work indicated that the biomass of two bacterial strains is an effective adsorbent for Cu2+ removal from aqueous solutions.

Current overview and future perspective in fungal biorecovery of metals from secondary sources

Microorganisms are intimately involved in many biogeochemical processes that underpin the transformation of metals and cycling of related substances, such as metalloids and radionuclides. Many processes determine the mobility and bioavailability of metals, thereby influencing their transfer to the environment and living organisms. These processes are closely related to global phenomena such as soil formation and bioweathering. In addition to environmental significance, microbial metal transformations play an essential role in both in situ and ex situ bioremediation processes for solid and liquid wastes. The solubilization of heavy metals from industrial waste and soil is commonly used in bioremediation. Moreover, immobilization processes are applicable to bioremediation of metals and radionuclides from aqueous solutions. This review provides an overview of critical metal extraction and recovery from secondary sources, applied microorganisms and methods, metal-microbe interactions, as well as a detailed description of known metal recovery mechanisms.

Towards electrochemical iridium recycling in acidic media: effect of the presence of organic molecules and chloride ions

The utilization of iridium is expected to surge in the next few years, notably due to the rising implementation of water electrolyzer devices in the energy transition. However, the natural resources of this noble metal are extremely limited and thus its recycling will become of high importance. Unfortunately, iridium is also the most corrosion resistant platinum group metal, making its recovery from waste a difficult and energy-demanding process. Hereby, we study the impact of organics and chloride ions on the electrochemical dissolution of iridium in order to pave the way towards green recycling of this precious metal. We present a 40 times increased dissolution when cycling iridium in presence of HCl and 1 M ethanol compared to HClO4. Our results point towards the direction of destabilizing Ir at relatively mild conditions in acidic media.

Cell population behavior of the unicellular red alga Galdieria sulphuraria during precious metal biosorption

This study investigates the biosorption mechanism, including cell population behavior, of trace amounts of precious metals (gold, palladium, and platinum) in a unicellular red alga, Galdieria sulphuraria. Single-cell inductively coupled plasma mass spectrometry showed that the number of adsorbing cells and the concentration of adsorbed metal per cell varied depending on solution acidity and metal species. The X-ray absorption fine structure in 5 mM HCl solution indicated that the adsorbed Au formed inner-sphere complexes with S, whereas the adsorbed Pd and Pt formed an inner-sphere complexes with N and/or S. In 500 mM HCl solution, the adsorbed Au and Pd formed inner-sphere complexes only with S, and the Au formed a structure similar to Au₂S. At higher acidity, Au and Pd were recovered by interacting with residues that formed more stable complexes, which was accompanied by changes in the behavior of cell populations adsorbing the metals. This is the first study to demonstrate the relationship between changes in the behavior of cell populations and chemical interactions that occur between substrate elements and biomaterial residues during biosorption. The findings of this study provide deeper insights into the biosorption mechanism and a background for the design of an environmentally friendly biosorbent.

Research trend and dynamical development of focusing on the global critical metals: a bibliometric analysis during 1991-2020

Critical metals are indispensable to a world seeking to transition away from carbon. Yet their extraction, processing, and application leave an unsustainable global environment and climate change footprint. To capture the development dynamics and research emphases of critical metals throughout their life cycle, this paper adopts bibliometrics to analyze the various stages of global critical metal flow in multiple dimensions to reveal the hot issues and future strategic trends. The research results indicate that the number of research papers on critical metals is annually rising, with remarkably rapid growth after 2010. Judging from the number of articles published by the authors and the citations, among the authors, Kawakita, Poettgen, Anwander, Inoue, and Dongmei Cui have a significant influence on critical metal research fields. The institutions with the most research on critical metals are universities, not research institutes. In addition, the focus has extended from a single discipline to the interdisciplinary development of multiple disciplines. Analysis of keywords shows that "rare metals" and "precious metals" are the most popular metals among the researched metals. The researched buzzwords of critical metals are disappearing, convergent, and merging over time. The research has focused on the mining and the whole life cycle process of extraction, treatment, and application. Based on the above characteristics, this paper tries to understand the dynamic development and evolution of global critical metals from multiple dimensions, resorting to giving a reference for follow-up-related research scholars.

Recovery of Au from dilute aqua regia solutions via adsorption on the lyophilized cells of a unicellular red alga Galdieria sulphuraria: A mechanism study

The high electrical conductivity, chemical stability, and low toxicity of elemental Au make it a highly valuable resource. However, wastewater produced during the mining, utilization, and disposal of Au inevitably contains small amounts (10-40 mg L^-1) of Au, thus posing environmental risks. It is too acidic to be treated with inexpensive and eco-friendly bioadsorbents previously studied for the remediation of less acidic effluents. Herein, lyophilized Galdieria sulphuraria cells are shown to directly adsorb Au from simulated Au-containing wastewater with a total acid concentration of 4 M, achieving an adsorption capacity of 35 ± 2.5 mg g^-1 Au after 30-min exposure and a selectivity that exceeds that of an ion-exchange resin and is comparable to that of activated carbon. Additionally, Au adsorbed on these cells is more easily eluted than that adsorbed on the ion-exchange resin or activated carbon. Detailed characterizations reveal that Au accumulates on the surface of lyophilized cells, where it is mainly present as AuCl₄^- and not as Au⁰, in contrast to a previously proposed adsorption mechanism. Thus, our work provides valuable insights into the mechanism of Au adsorption on biomaterials and paves the way to the cheap and eco-friendly recovery of Au from acidic wastewater.

Biotechnological synthesis of Pd-based nanoparticle catalysts

Palladium metal nanoparticles are excellent catalysts used industrially for reactions such as hydrogenation and Heck and Suzuki C-C coupling reactions. However, the global demand for Pd far exceeds global supply, therefore the sustainable use and recycling of Pd is vital. Conventional chemical synthesis routes of Pd metal nanoparticles do not meet sustainability targets due to the use of toxic chemicals, such as organic solvents and capping agents. Microbes are capable of bioreducing soluble high oxidation state metal ions to form metal nanoparticles at ambient temperature and pressure, without the need for toxic chemicals. Microbes can also reduce metal from waste solutions, revalorising these waste streams and allowing the reuse of precious metals. Pd nanoparticles supported on microbial cells (bio-Pd) can catalyse a wide array of reactions, even outperforming commercial heterogeneous Pd catalysts in several studies. However, to be considered a viable commercial option, the intrinsic activity and selectivity of bio-Pd must be enhanced. Many types of microorganisms can produce bio-Pd, although most studies so far have been performed using bacteria, with metal reduction mediated by hydrogenase or formate dehydrogenase enzymes. Dissimilatory metal-reducing bacteria (DMRB) possess additional enzymes adapted for extracellular electron transport that potentially offer greater control over the properties of the nanoparticles produced. A recent and important addition to the field are bio-bimetallic nanoparticles, which significantly enhance the catalytic properties of bio-Pd. In addition, systems biology can integrate bio-Pd into biocatalytic processes, and processing techniques may enhance the catalytic properties further, such as incorporating additional functional nanomaterials. This review aims to highlight aspects of enzymatic metal reduction processes that can be bioengineered to control the size, shape, and cellular location of bio-Pd in order to optimise its catalytic properties.

Bio- and phytoremediation: plants and microbes to the rescue of heavy metal polluted soils

Bio- and phytoremediation, being encouraging terms implying the use of biological systems for cleansing purposes, have risen a worthy venture toward environmental restoration in discouraging scenarios, such as the augmentation of indestructible heavy metals. Hyperaccumulating plants and heavy metal resistant microbes own mechanisms embedded in their metabolism, proteins, and genes that confer them with “super characteristics” allowing them to assimilate heavy metals in order to amend polluted soils, and when combined in a symbiotic system, these super features could complement each other and be enhanced to overpower the exposure to toxic environments. Though xenobiotic pollution has been an object of concern for decades and physicochemical procedures are commonly carried out to offset this purpose, a “live” remediation is rather chosen and looked upon for promising results. A variety of benefits have been registered from symbiotic relationships, including plants teaming up with microbes to cope down with non-biodegradable elements such as heavy metals; but a carefully maneuvered interaction might signify a greater insight toward the application of bioremediation systems. These manipulations could consist of genetic engineering and/or additional supplementation of molecules and microbes. In the present study, a contemporary connection between plants and microbes involving their controlled management is summarized in a visionary display.

Phytomining of noble metals - A review

Phytomining of noble metals (NMs) offers a promising possibility of metal extraction at sites where traditional mining activities or recovering NMs from low-grade minerals are not competitive. In addition to conventional mining, producing NMs from secondary resources strengthening the circular economy has been paid worldwide attention. The review presented in this paper links three scientific areas as the essential elements to form the phytomining chain of NMs. The accumulation of NMs in plants is the first step, referred as the phytoextraction process. This is followed by heightening the concentration of NMs via the enrichment stage. Eventually, although less well understood, extraction methods of NMs from biomass solid remains as well as from diverse secondary sources particularly incineration ashes are discussed that assist to visualize the potential pathways in phytomining.

Bioleaching of copper and nickel from mobile phone printed circuit board using Aspergillus fumigatus A2DS

The recovery of metals from electronic waste was investigated by using fungal strain Aspergillus fumigatus A2DS, isolated from the mining industry wastewater. Fifty-seven percent of copper and 32% of nickel were leached (analyzed by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-OES)) by the organism after one-step leaching at a temperature of 30 °C (shaking condition for 7 days). Maximum % of copper and nickel were obtained at a pH of 6 (58.7% Cu and 32% Ni), the temperature of 40 °C (61.8% Cu and 27.07% Ni), a pulp density of 0.5% (62% Cu and 42.37% Ni), and inoculums of 1% (58% Cu and 32.29% Ni). The XRD pattern of PCB showed 77.6% of copper containing compounds. XRD analysis of the leachate residue showed only 23.2% Euchorite (ASCu2H7O8) and 9.4% other copper containing compounds, indicating the leaching property of the fungus. HPLC analysis of the spent medium showed the presence of different acids like citric, succinic, and fumaric acid. The FTIR spectrum showed a decrease in carboxylic stretching in the leachate produced after bioleaching using spent medium. ICPOES of the leachate obtained using spent medium showed that 61% of the copper and 35% of nickel were leached out after seven days of incubation at shaking condition and 57% of copper and 32.8% of nickel at static condition confirming acidolysis property of the strain. A. fumigatus A2DS metal absorption and adsorption ability were observed using transmission electron microscopy (TEM) and scanning electron microscopy energy dispersive X-ray (SEM-EDX) respectively. The results thus indicate that bioleaching of Cu and Ni is bioleached by A. fumigatus A2DS.

Removal of metals from aqueous solutions using dried Cladophora parriaudii of varying biochemical composition

Macroalgal biosorption has shown promise for the removal of metal ions from wastewaters, whose presence can pose a threat to the aquatic environment. There is a wealth of literature published on macroalgal biosorption, the common thread being that the biosorbent material was collected from the field, under undefined conditions. These studies offer little insight into the impact of prior cultivation or biomass production practices upon the biosorbent material, its adsorptive physico-chemical properties and its subsequent capacity for metal removal. The present study sought to investigate the influence of changes in macroalgal cultivation, specifically nutrient regime, upon biomass properties and the resultant adsorption performance. The macroalga Cladophora parriaudii was cultivated under six different nutrient regimes; 2:1 and 12:1 N:P molar ratios, with nitrogen supplied either as ammonium (NH₄⁺), nitrate (NO₃^-), or urea (CO(NH₂)₂). These nutrient regimes were designed to produce biomass of varying biochemical and cell surface profiles. After cultivation, the biomass was rinsed, dried, biochemically analysed and then used for the removal of four individual metals from solution. Metal removal varied considerably between treatments and across initial metal concentrations, with removal values of 46-85%, 9-80%, 8-71%, and 49-94% achieved for Al, Cu, Mn, and Pb, respectively, with initial metal concentrations varying between 0 and 150 mg L^-1. The observed variation in metal removal can only be attributed to differences in biochemistry and cell surface properties of the biosorbent induced by nutrient regime, as all other variables were constant. This study demonstrates that prior cultivation conditions influence the biochemistry of a biosorbent material, namely macroalgae Cladophora parriaudii, which has an impact upon metal removal. This aspect should be given due consideration for future biosorption research and when reviewing already published literature.

Gold(III) recovery from aqueous solutions by raw and modified chitosan: A review

Chitosan, a prestigious versatile biopolymer, has recently received considerable attention as a promising biosorbent for recovering gold ions, mainly Au(III), from aqueous solutions, particularly in modified forms. Confirming the assertion, this paper provides an up-to-date overview of Au(III) recovery from aqueous solutions by raw (unmodified) and modified chitosan. A particular emphasis is placed on the raw chitosan and its synthesis from chitin, characteristics of raw chitosan and their effects on metal sorption, modifications of raw chitosan for Au(III) sorption, and characterization of raw chitosan before and after modifications for Au(III) sorption. Comparisons of the sorption (conditions, percentage, capacity, selectivity, isotherms, thermodynamics, kinetics, and mechanisms), desorption (agents and percentage), and reusable properties between raw and modified chitosan in Au(III) recovery from aqueous solutions are also outlined and discussed. The major challenges and future prospects towards the large-scale applications of modified chitosan in Au(III) recovery from aqueous solutions are also addressed.

Bioremediation of noxious metals from e-waste printed circuit boards by Frankia

The environmental noxious e-waste was collected and physicochemical characterized by Scanning electron microscopy (SEM) along with energy dispersive X-ray spectroscopy (EDX), Atomic absorption spectrometry (AAS), and X-ray diffraction analysis (XRD) exploration to understand the presence of toxic metals like Hg, Cd, Pd, Si, Ru. Therefore, the finding provides vital knowledge about the impact of toxic metals from e-waste printed circuit boards as contaminants in the environment and its impact on humans. The Frankia sp. DDNSF-03 and Frankia casuarinae DDNSF-04 were isolated and identified, further utilized for removal of e-waste toxic metals by one and two steps bioremediation experiments executed with various e-waste concentrations. The two-step bioremediation experiment is efficient in the expression of toxic metals that were removed at a lesser concentration of e-waste. Consequently, the presence of organic acids in the Frankia primary metabolites was confirmed by FT-IR analysis besides decreasing the pH level in the Frankia growth medium. The positive control Frankia and negative control e-waste were maintained throughout the bioremediation experiments. The initial Hg 4.3, Cd 8.3, Pd 4.6 (ppm) in the e-waste and final treated with Frankia sp. DDNSF-03 Hg 0.09, Cd 5.09, Pb 0.49 (ppm), and Frankia casuarinae DDNSF-04 Hg 2.15, Cd 5.6, Pb 2.82 (ppm) concentration of toxic metals was quantified by AAS spectrum analysis. The toxic metals mercury and lead were significantly mineralized by Frankia sp. when compare the Frankia casuarinae. The above finding was confirmed the manifestation of morphological changes by an accumulation of e-waste in Frankia hyphae using SEM analysis and obtain the qualitative of toxic metals parallel peaks in EDX analysis.

Uptake and Recovery of Gold from Simulated Hydrometallurgical Liquors by Adsorption on Pine Bark Tannin Resin

The recovery of critical and precious metals from waste electrical and electronic equipment (WEEE) is an environmental and economic imperative. Biosorption has been considered a key technology for the selective extraction of gold from hydrometallurgical liquors obtained in the chemical leaching of e-waste. In this work, the potential of tannin resins prepared from Pinus pinaster bark to sequester and recover gold(III) from hydrochloric acid and aqua regia solutions was assessed. Equilibrium isotherms were experimentally determined and maximum adsorption capacities of 343 ± 38 and 270 ± 19 mg g−1 were found for Au uptake from HCl and HCl/HNO3 (3:1 v/v) solutions containing 1.0 mol L−1 H+. Higher levels of acidity (and chloride ligands) significantly impaired the adsorption of gold from both kinds of leaching solutions, especially in the aqua regia system, in which the adsorbent underperformed. Pseudo-first and pseudo-second order models successfully described the kinetic data. The adsorbent presented high selectivity towards gold. Actually, in simulated aqua regia WEEE liquors, Au(III) was extensively adsorbed, compared to Cu(II), Fe(III), Ni(II), Pd(II), and Zn(II). In three adsorption–desorption cycles, the adsorption capacity of the regenerated adsorbent moderately decreased (19%), although the gold elution in acidic thiourea solution had been quite limited. Future research is needed to examine more closely the elution of gold from the exhausted adsorbents. The results obtained in this work show good perspectives as regards the application of pine bark tannin resins for the selective extraction of Au from electronic waste leach liquors.

Photodegradation of Phenolic Compounds from Water in the Presence of a Pd-Containing Exhausted Adsorbent

A closed-cycle technology regarding the use of an exhausted Pd-based adsorbent as a photocatalyst in the degradation process of phenol is presented. Pd (II) represents a precious metal of great economic importance. Its obtained from natural sources become more difficult to achieve. Therefore, also considering the regulations of the “circular economy,” its recovery from secondary sources turn out to be a stringent issue in the last years. Pd(II) ions are removed from aqueous solution through adsorption onto Florisil (an inorganic solid support—magnesium silicate) impregnated with Cyphos IL 101 (trihexyl tetradecyl phosphonium chloride). It was observed that the presence of the ionic liquid (IL) in the adsorbent structure doubles the adsorption efficiency of the studied materials. The newly obtained Pd-based photocatalyst was exhaustively characterized and was used in the degradation process of phenol from aqueous solutions. The phenol degradation process was studied in terms of the nature of the photocatalyst used, time of photodegradation and solid: liquid ratio. It was observed that both the presence of IL and Pd lead to an increase in the efficiency of the phenol degradation process. The new Pd-based photocatalyst could be efficiently used in more cycles of phenol photodegradation processes. When is used as a photocatalyst the Florisil impregnated with IL and loaded with 2 mg/g of Pd, a degree of mineralization of 93.75% is obtained after 180 min of irradiation of a phenol solution having a concentration of 20 mg/L and using a solid:liquid ratio = 1:1.

Effect of Ionic Strength and Coexisting Ions on the Biosorption of Divalent Nickel by the Acorn Shell of the Oak Quercus crassipes Humb. & Bonpl

This study investigated the effect of ionic strength and background electrolytes on the biosorption of Ni2+ from aqueous solutions by the acorn shell of Quercus crassipes Humb. & Bonpl. (QCS). A NaCl ionic strength of 0.2 mM was established to have no effect on the Ni2+ biosorption and the biosorption capacity of the heavy metal decreased as the ionic strength increased from 2 to 2000 mM. The background electrolytes (KCl, NaNO3, Na2SO4, CaCl2, MgSO4, and MgCl2) had no adverse effects on the biosorption of Ni2+ at a concentration of 0.2 mM. However, at background electrolyte concentrations of 2 and 20 mM, divalent cations (Ca2+ and Mg2+) had greater negative effects on the biosorption of Ni2+ compared to the monovalent cations (Na+ and K+). Additionally, the SO42− and Cl− anions affected the biosorption of Ni2+. The fractional power, Elovich, and pseudo-second order models represented the kinetic processes of the biosorption of Ni2+ adequately. The results show that QCS can be a promising and low-cost biosorbent for removing Ni2+ ions from aqueous solutions containing various types of impurities with different concentrations.

Estimation on Fixed-Bed Column Parameters of Breakthrough Behaviors for Gold Recovery by Adsorption onto Modified/Functionalized Amberlite XAD7

The objective of this paper was to evaluate the potential of a new adsorbent material to recover Au (III) from real wastewater, in a column with a fixed bed in a dynamic regime. The material was obtained through functionalization, by impregnation of the commercial resin, Amberlite XAD 7 type, with L-glutamic acid, which has active groups -NH2 and -COOH. The goal of the experiments was to follow the correlation of fixed-bed column specific adsorption parameters (the effluent volume, the amounts of adsorbent, heights of the adsorbent layer in column) with the time necessary to cross the column. The experimental data obtained were modeled, using the Bohart-Adams, Yoon-Nelson Thomas and Clark models, to establish the mechanism of the Au (III) recovery process, in a dynamic regime. Also, we established the number of cycles for adsorption-desorption for which the new material can be used. We used 5% HNO3 (5%) as desorption agent in five adsorption-desorption cycles, until the process was no longer efficient. The degree of desorption varied between 84% and 34% from cycle 1 to cycle 5.

Chelating polymers with valuable sorption potential for development of precious metal recycling technologies

A special attention is currently focused on the recovery of Au, Ag, Pt, Pd and Rh from both primary and secondary sources. From the wide range of sorbents that have been used in this respect, the required selectivity is proved only by the chelating polymers containing donor N, O and S atoms in their functional groups. This work presents the recent published researches on this topic, pointing out the capabilities of chelating sorbents based on organic synthetic polymers for a sustainable development. The chelating sorbents are differentiated and reviewed according to their synthesis strategy and compatibility with synthetic and real matrices. First, an overview on the novel functionalized polymers and impregnated resins with good selectivity for the recovery of most valuable precious metals from synthetic leach solutions is given. Subsequently, the performances of these materials in the selective and preconcentrative recovery of Au, Ag, Pt, Pd and Rh from simulated and real leachates are discussed. The viability of an integrated approach for the determination of precious metals from simulated solutions by solid phase spectrometry is highlighted. The transposition of chelating polymers’ potential in challenging technologies for precious metal recovery-reuse-recycling needs further research on directions that are proposed.

Draft genome sequence of Deinococcus sp. KR-1, a potential strain for palladium-leaching

Strain KR-1 was isolated from pond water collected in Japan. Because this strain was capable of adsorbing palladium particles in sterilized water, strain KR-1 will be a useful biocatalyst for palladium-leaching from metal waste. Here we present a draft genome sequence of Deinococcus sp. KR-1, which consists of a total of 7 contigs containing 4,556,772 bp with a GC content of 70.0% and comprises 4,450 predicted coding sequences. Based on the 16S rRNA gene sequence analysis, strain KR-1 was identified as Deinococcus sp. KR-1.

Recovery of Copper from Leached Tailing Solutions by Biosorption

Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased which has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium, and rare earth elements which transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid–liquid separation that processes solutions with low concentrations of metals corresponds to adsorption, and more recently biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in different types of biomass. Bacterial, fungal, plant, and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit, in the north of Chile, and after an acid leaching copper was biosorbed, kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH, and initial metal concentration were studied.

Luminescence properties of the Ln-EDTA complexes covalently linked to the chitosan biopolymers containing β-diketonate as antenna ligands

This paper reports on the preparation, characterization, and photoluminescence properties of novel hybrid materials, in which the EDTA-Ln-L complexes (where L: H₂ O, acac, bzac, dbm, and tta ligands, and Ln: Eu, Gd, and Tb) were covalently linked to the precursor medium molecular weight chitosan surface (CS) matrices or on the chitosan surfaces previously crosslinked with epichlorohydrin (CSech). The emission spectra of these materials were characterized by intraconfigurational-4fN transitions centred on the Eu³⁺ and Tb³⁺ ions. Some broad bands from the polymeric matrix were also observed in the emission spectra, however the relative intensities of the intraconfigurational bands increased significantly for systems containing diketonate ligands when the antenna effect became more efficient. The values of the radiative rates (A_rad ) were higher for crosslinked hybrid systems with epichlorohydrin, while nonradiative rates (A_nrad ) presented the opposite behaviour. These data contributed to an increase in the values of emission quantum efficiency (η) for crosslinked materials. The effect of the modification process and antenna ligand on the values of intensities, intensity parameters Ω₂ e Ω₄ of the Eu³⁺ complexes were also investigated. The results showed that the crosslinked biopolymer surfaces have great potential for applications in molecular devices light converters.

Development of novel sericin and alginate-based biosorbents for precious metal removal from wastewater

In this study, two novel low water-soluble sericin and alginate-based biosorbents were successfully developed for precious metal removal from wastewater: sericin and alginate particles chemically crosslinked by proantocyanidins (SAPAs) and sericin, alginate and polyvinyl alcohol particles (SAPVA). The proportions of proantocynidins (PAs) or polyvinyl alcohol (PVA) added to sericin (2.5% w/v) and alginate (2.0% w/v) blend were 0.5, 1.5, 2.5 and 3.5% w/v. Among these concentrations, particles produced with 0.5% w/v of PVA or 2.5% w/v of PAs presented the lowest water solubility percentages (3.74 ± 0.05 and 3.56 ± 0.21%, respectively) and the following metallic affinity order: AuCl₄^- > PdCl₄^2- > PtCl₆^2- > Ag⁺. Then, gold biosorption kinetics by SAPAs was evaluated at three gold initial concentrations (72.88, 187.12, and 273.79 mg/L), and its performance was compared to activated carbon adsorbent uptake. The data modeling revealed that the process follows pseudo-first-order kinetics and is mainly controlled by external diffusion. SAPAs before and after gold biosorption (SAPAs-gold) were characterized by scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, optical microscopy, helium pycnometry, mercury porosimetry, N₂ physisorption, and Fourier-transform infrared spectroscopy.

Photochemically Enhanced Selective Adsorption of Gold Ions on Tannin-Coated Porous Polymer Microspheres

Metal recovery from electronic waste and industrial wastewater has attracted increasing attention to recycle precious metals and inhibit the emission of hazardous heavy metals. However, the selective recovery of precious metals with a large quantity is still very challenging because wastewater contains a variety of different cations while precious metal ions are relatively scarce. Here, we introduce a simple method to selectively increase the adsorption of gold ions using tannin-coated porous polymer microspheres through photochemical reduction. Mesoporous poly(ethylene glycol dimethacrylate- co-acrylonitrile) microspheres with an average pore diameter of 13.8 nm were synthesized and used as an adsorbent matrix. Tannic acid (TA) was deposited onto the internal pores of the polymer matrix by simple immersion in an aqueous milieu. TA coatings increased the maximum number of adsorbed gold ions by 1.3 times because of the well-known metal ion chelation of TA. Under light illumination, the maximum number of adsorbed gold ions dramatically increased by 6.1 times. We examined two distinct mechanisms presumably involved in the enhanced adsorption: the photooxidation of TA and plasmon-induced hot electrons. Moreover, TA-coated microspheres exhibited remarkable selectivity for gold ions among competing metal ions commonly found in waste resources. This work suggests that the photochemically activated TA can serve as an excellent adsorbent for the selective and efficient recovery of gold ions from wastewater.

Biochar versus bone char for a sustainable inorganic arsenic mitigation in water: What needs to be done in future research?

Arsenic (As) is an emerging contaminant on a global scale posing threat to environmental and human health. The relatively brief history of the applications of biochar and bone char has mapped the endeavors to remove As from water to a considerable extent. This critical review attempts to provide a comprehensive overview for the first time on the potential of bio- and bone-char in the immobilization of inorganic As in water. It seeks to offer a rational assessment of what is existing and what needs to be done in future research as an implication for As toxicity of human health risks through acute and chronic exposure to As contaminated water. Bio- and bone-char are recognized as promising alternatives to activated carbon due to their lower production and activation cost. The surface modification via chemical methods has been adopted to improve the adsorption capacity for anionic As species. Surface complexation, ion exchange, precipitation and electrostatic interactions are the main mechanisms involved in the adsorption of As onto the char surface. However, arsenic-bio-bone char interactions along with their chemical bonding for the removal of As in aqueous solution is still a subject of debate. Hence, the proposed mechanisms need to be scrutinized further using advanced analytical techniques such as synchrotron-based X-ray. Moving this technology from laboratory phase to field scale applications is an urgent necessity in order to establish a sustainable As mitigation in drinking water on a global scale.

Enhancement of platinum biosorption by surface-displaying EC20 on Escherichia coli

To increase the platinum adsorption capacity of Escherichia coli (E. coli) biomass, we fused EC20 protein to the E. coli cell surface using an InaKN-based display system, which is the N-terminal region of ice nucleation protein that can be employed as a cell surface display motif. The media and culture conditions were optimized for EC20 (a phytochelatin analogue with 20 repeating units of glutamate and cysteine) expression and Pt (IV) biosorption. Furthermore, the adsorption process was elucidated from aspect of adsorption kinetics and equilibrium, and the characterization of blank and Pt-loaded cells were analyzed using SEM, AFM, TEM, FT-IR and XPS. Our study demonstrated that E. coli strain, which had InaKN-EC20 protein expressed on the cell surface, showed a great enhancement in Pt (IV) adsorption under optimized condition when comparing with that of original E. coli strain. The SEM-EDX analysis revealed that the cellular morphology has been changed in Pt-loaded cells, and the weight percent of platinum in the surface of E.coli increased substantially after displaying EC20 protein. Furthermore, intracellular platinum accumulation was detected in Pt-loaded EC20 cells since a clear peak of platinum exhibited, implying that cytoplasmic EC20 protein might also contribute to platinum accumulation. FTIR analysis revealed that the predominant functional groups in platinum adsorption were amine, carboxyl and phosphate groups.

The possible mechanism of the formation of silver nanoparticles by Penicillium cyclopium

This contribution describes the biomineralization of silver nanoparticles by the microbial reduction of Ag (I) ions using the mycelium and the cell-free extract of Penicillium cyclopium. Different techniques, such as UV-Vis, SEM, TEM, FT-IR and GPC were used to characterize the obtained nanoparticles and understand the mechanism of their biosynthesis. The SEM and TEM images demonstrated the presence of silver nanoparticles on the mycelia surface suggesting that these particles are synthesized on the fungal cell wall. FT-IR analysis of the mycelium revealed two main types of compounds (saccharides and proteins) and these molecules might be involved in the formation of silver nanoparticles on the surface of mycelium. Ultraviolet-visible spectroscopy and TEM analysis confirmed the formation of silver nanoparticles with different shapes by the cell-free extract of P. cyclopium. Their size ranges from 12 to 25 nm and possess an average size of 16 ± 6 nm. GPC analysis of this filtrate revealed a few peaks responsible for polysaccharides and proteins presence. The only protein fraction with the mass approximately to 5000 Da indicated the formation of silver nanoparticles. Polypeptide(s) as the major molecules involved in biomineralization of silver by the cell-free extract of P. cyclopium are suggested. Enzymatic synthesis of silver nanoparticles by the mycelium and the cell-free extract of P. cyclopium is excluded.

Differences of cell surface characteristics between the bacterium Pseudomonas veronii and fungus Ophiostoma stenoceras and their different adsorption properties to hydrophobic organic compounds

The first step of microbial biodegradation is the adsorption of pollutants on the microorganisms' surface, which is determined by the microorganism type and pollutant hydrophobicity. One fungus Ophiostoma stenoceras LLC and one bacterium Pseudomonas veronii ZW were chosen for the investigation of cell surface hydrophobicity and adsorption abilities to various organic compounds. Results showed that the fungus could better capture and adsorb organic compounds in liquid and gas phases, and the adsorption was a physical monolayer adsorption process. Much smaller partition coefficient for gas-fungus suggested that direct gaseous adsorption was preferred. The XPS (X-ray photoelectron spectroscopy) characterization further confirmed that several functional groups changed after the adsorption of compounds. The time taken for complete degradation of hexane, tetrahydrofuran and chlorobenzene was shorter with the addition of O. stenoceras LLC. Such findings are useful in exploring the special cell surface of fungus in adsorption and bioenhancement for organic treatment of organic contaminants using bacteria.

Biotechnological strategies for the recovery of valuable and critical raw materials from waste electrical and electronic equipment (WEEE) - A review

Critical raw materials (CRMs) are essential in the development of novel high-tech applications. They are essential in sustainable materials and green technologies, including renewable energy, emissionfree electric vehicles and energy-efficient lighting. However, the sustainable supply of CRMs is a major concern. Recycling end-of-life devices is an integral element of the CRMs supply policy of many countries. Waste electrical and electronic equipment (WEEE) is an important secondary source of CRMs. Currently, pyrometallurgical processes are used to recycle metals from WEEE. These processes are deemed imperfect, energy-intensive and non-selective towards CRMs. Biotechnologies are a promising alternative to the current industrial best available technologies (BAT). In this review, we present the current frontiers in CRMs recovery from WEEE using biotechnology, the biochemical fundamentals of these bio-based technologies and discuss recent research and development (R&D) activities. These technologies encompass biologically induced leaching (bioleaching) from various matrices,biomass-induced sorption (biosorption), and bioelectrochemical systems (BES).