Biofiltration of volatile organic compounds using fungi and its conceptual and mathematical modeling

Chemical structure of hydrocarbons significantly affects removal performance and microbial responses in gas biotrickling filters

The control of emissions of short-chain hydrocarbons with different structures is critical for the petrochemical industry. Herein, three two-carbon-containing (C2) hydrocarbons, ethane, ethylene, and acetylene, were chosen as pollutants to study the effects of chemical structure of hydrocarbons on removal performance and microbial responses in biotrickling filters. Results showed that the removal efficiency (RE) of C2 hydrocarbons followed the sequence of acetylene > ethane > ethylene. When the inlet loading rate was 30 g/(m3·h) and the empty bed residence time was 60 s, the RE of ethane, ethylene, and acetylene was 57 ± 4.0 %, 49 ± 1.0 %, and 84 ± 2.7 %, respectively. The high water solubility resulted in the high removal of C2 hydrocarbons, while a low surface tension enhanced the removal of C2 hydrocarbons. Additionally, the microbial community, enzyme activity, and extracellular properties of microorganisms also contributed to the difference in C2 hydrocarbon removal. These results could be referred for the effective control of light hydrocarbon emissions.

Low cost and renewable H2S-biofilter inoculated with Trichoderma harzianum

The use of biogas to produce hydrogen is currently gaining more attention. One of the drawbacks for the valorization of biogas is the presence of H2S, a hazardous molecule that can cause damage in the metallic internal structures of industries. In this study, the H2S-removal performance of a fungi-based biofilter was investigated. First, an H2S-resistant fungal species was isolated from an industrial digestate and identified as Trichoderma harzianum. The capacity of this microorganism to metabolize H2S in a mineral medium was confirmed. Then, a bioreactor was constructed and put in place to monitor the elimination of gaseous H2S. A mix of cardboard, perlite, woodchips, and wood pellets was used as filling. Microbial development and the outlet gas composition were monitored during a 60-day experimental process during which H2S was completely removed. 97% of the introduced sulphur was detected in the used filling material (fungal species + packing material) by elemental analysis. 24% of the detected sulphur was identified by ion-exchange chromatography as SO42-. Elemental analysis, gas chromatography, and ion-exchange chromatography were used to determine the bioreactor sulphur balance. Metagenomic analysis underlined that H2S elimination was due to the presence of Trichoderma harzianum with a H2S-specific bacterial consortium.

Enhancing air treatment through controlled fabrication of transition metal-doped titanium dioxide nanocomposites for photocatalytic toluene degradation

Rapid industrial growth and urbanization have resulted in a significant rise in environmental pollution issues, particularly indoor air pollutants. As a result, it is crucial to design and develop technologies and/or catalysts that are not only cost-effective but also promising high performance and practical applicability. However, achieving this goal has been so far remained a challenging task. Herein, a series of transition metal M - TiO2 (M = W, Fe, Mn) nanocrystals was prepared for photocatalytic degradation of volatile organic compounds (VOCs), i.e., toluene. Of the nanocomposites tested, W-TiO2 showed significantly improved photocatalytic activity for VOC degradation under UV irradiation compared to the others. In particular, the optimized W dopant amount of 0.5 wt% resulted in the outstanding degradation performance of toluene (96%) for the obtained W-TiO2(0.5%) nanocomposite. Moreover, W-TiO2(0.5%) nanocomposite exhibited good stability for 32 h working under high toluene concentration (10 ppm) compared to the pristine TiO2. The current work demonstrates the potential usage of M - TiO2 nanocrystals, particularly W-TiO2(0.5%), as a promising photocatalyst for efficient VOCs degradation.

A review of the recent progress in biotrickling filters: packing materials, gases, micro-organisms, and CFD

Organic pollutants in the air have serious consequences on both human health and the environment. Among the various methods for removing organic pollution gas, biotrickling filters (BTFs) are becoming more and more popular due to their cost-effective advantages. BTF can effectively degrade organic pollutants without producing secondary pollutants. In the current research on the removal of organic pollutants by BTF, improving the performance of BTF has always been a research hotspot. Researchers have conducted studies from different aspects to improve the removal performance of BTF for organic pollutants. Including research on the performance of BTF using different packing materials, research on the removal of various mixed pollutant gases by BTF, research on microbial communities in BTF, and other studies that can improve the performance of BTF. Moreover, computational fluid dynamics (CFD) was introduced to study the microscopic process of BTF removal of organic pollutants. CFD is a simulation tool widely used in aerospace, automotive, and industrial production. In the study of BTF removal of organic pollutants, CFD can simulate the fluid movement, mass transfer process, and biodegradation process in BTF in a visual way. This review will summarize the development of BTFs from four aspects: packing materials, mixed gases, micro-organisms, and CFD, in order to provide a reference and direction for the future optimization of BTFs.

Air biofilters for a mixture of organic gaseous pollutants: an approach for industrial applications

Hazardous airborne pollutants are frequently emitted to the atmosphere in the form of a gaseous mixture. Air biofilters as the primary biotechnological choice for waste gas treatment (low inlet concentration and high gas flow rate) should run properly when the feed contains multiple pollutants. Simultaneous removal of pollutants in biofilters has been extensively studied over the last 10 years. In this review, the results and findings of the mentioned studies including different groups of pollutants, such as methane (CH4) and volatile organic compounds (VOCs) are discussed. As the number of pollutants in a mixture increases, their elimination might become more complicated due to interactions between the pollutants. Parallel batch studies might be helpful to better understand these interaction effects in the absence of mass transfer limitations. Setting optimum operating conditions for removal of mixtures in biofilters is challenging because of opposing properties of pollutants. In biofilters, concerns, such as inlet gas composition variation and stability while dealing with abrupt inlet load and concentration changes, must be managed especially at industrial scales. Biofilters designed with multi-layer beds, allow tracking the fate of each pollutant as well as analyzing the diversity of microbial culture across the filter bed. Certain strategies are recommended to improve the performance of biofilters treating mixtures. For example, addition of (bio)surfactants as well as a second liquid phase in biotrickling filters might be considered for the elimination of multiple pollutants especially when hydrophobic pollutants are involved.

Development of a CFD model indicating the quantitative relationship among reactor dimension, bed flow unevenness, and performance for VOCs biofilters

This study presents a Computational Fluid Dynamics (CFD) based biofiltration model to investigate the airflow distribution and the impact of bed flow unevenness (BFU) on the removal of Volatile Organic Compounds (VOCs) in biofilters. The biofiltration model consists of a gas flow sub-model and a VOCs removal sub-model, which were validated by pilot-scale experiments. The model was used to examine the quantitative relationship among reactor dimensions, including the width to height ratio of the filter bed and empty bed residence time (EBRT), BFU, and performance for VOCs biofilters. Simulation results demonstrate that the flow unevenness index (FUI) of the packing layer changes from 0.06 to 0.48 m2‧s-1 with reactor dimension changes. With an increase in the width to height ratio at a constant EBRT, FUI increases, BFU changes, and flow velocity fluctuation on the cross-section becomes larger, leading to a reduction of about 10% in VOCs removal efficiency. Concentration distribution of VOCs becomes uneven in the horizontal direction. At a constant width to height ratio of the filter bed, an increase in EBRT causes an increase in FUI, leading to a decrease in VOCs removal efficiency. When the width to height ratio is 0.5, velocity fluctuation of filter bed cross-section is small, the concentration of VOCs decreases evenly across the filter bed layer, and FUI is at a low level (0.06-0.11 m2‧s-1).Implication: In this manuscript, a biofiltration model of VOCs biofilter based on CFD has constructed and validated. And the manuscript gave the quantitative relationship among reactor dimension, bed flow unevenness and performance for VOCs biofilters for the first time. This study can lead to enhanced VOCs removal efficiency and improved overall performance of biofilters in practical engineering applications.

A novel integrated industrial-scale biological reactor for odor control in a sewage sludge composting facility: Performance, pollutant transformation, and bioaerosol emission mechanism

In order to remove multiple pollutants in the sewage sludge (SS) composting facility, a novel integrated industrial-scale biological reactor based on biological trickling filtration and fungal biological filtration (BTF-FBF) was developed. This study examined bioaerosol emission, odour removal, pollutant transformation mechanism, and project investment. At an inlet flow rate of 7200 m³/h, the average removal efficiencies of hydrogen sulfide (H₂S), ammonia (NH₃), and volatile organic compounds (VOCs) during the steady stage were 97.2 %, 98.9 %, and 92.2 %. The BTF-FBF separates microbial phases (bacteria and fungi) of different modules. BTF removed most hydrophilic compounds, while FBF removed hydrophobic ones. Moreover, the reactor could effectively remove pathogens or opportunistic pathogens bioaerosols, such as Escherichia coli (61.9%), Salmonella sp. (85%), and Aspergillus fumigatus (82.1%). The pollutant transformation mechanism of BTF-FBF was proposed. BTF-FBF annualized costs were 324,783 CNY/year at 15 years. In conclusion, BTF-FBF provides new insights into composting facility bioaerosol, odour, and pathogen emission control.

Control of odor emissions from livestock farms: A review

Odor emission seriously affects human and animal health, and the ecological environment. Nevertheless, a systematic summary regarding the control technology for odor emissions in livestock breeding is currently lacking. This paper summarizes odor control technology, highlighting its applicability, advantages, and limitations, which can be used to evaluate and identify the most appropriate methods in livestock production management. Odor control technologies are divided into four categories: dietary manipulation (low-crude protein diet and enzyme additives in feed), in-housing management (separation of urine from feces, adsorbents used as litter additive, and indoor environment/manure surface spraying agent), manure management (semi-permeable membrane-covered, reactor composting, slurry cover, and slurry acidification), and end-of-pipe measures for air treatment (wet scrubbing of the exhaust air from animal houses and biofiltration of the exhaust air from animal houses or composting). Findings of this paper provide a theoretical basis for the application of odor control technology in livestock farms.

Evaluation of VOCs from fungal strains, building insulation materials and indoor air by solid phase microextraction arrow, thermal desorption-gas chromatography-mass spectrometry and machine learning approaches

Solid phase microextraction Arrow and thermal desorption-gas chromatography-mass spectrometry allowed the collection and evaluation of volatile organic compounds (VOCs) emitted by fungal cultures from building insulation materials and in indoor air. Principal component analysis, linear discriminant analysis and supported vector machine were used for visualization and statistical assessment of differences between samples. In addition, a screening tool based on the soft independent modelling of class analogies (SIMCA) was developed for identification of fungal contamination of indoor air. Ten different fungal strains, incubated under ambient and microaerophilic conditions, were analyzed for time period ranging from 5 to 29 days after inoculation resulting in a total of 140 samples. In addition, the effect of additives on the fungal growing media was studied. The total number of compounds and concentration values were used for the evaluation of the results. Clear differences were observed for VOC profiles emitted by different fungal strains by exploiting long chain alcohols (3-octanol, 1-hexanol and 2-octen-1-ol) and sesquiterpenes (farnesene, cuprene). The analysis of glass-wool and cellulose based building insulation materials (3 samples) gave clear differences, mainly for oxygenated compounds (ethyl acetate and hexanal) and benzenoids (benzaldehyde). Moreover, the comparison of indoor air and insulation materials collected from a house with fungal indoor air problems indicated that 42% of the VOCs were found in both samples. The analysis of 52 indoor air samples demonstrated clear differences in their VOC profiles, especially for hydrocarbons, and between control (44 samples) and indoor air problem houses (8 samples). Finally, the SIMCA model enabled to recognize differences between control and fungi contaminated houses with a prediction capacity over 84%.

Photo-Activated Direct Catalytic Oxidation of Gaseous Benzene with a Cu-Connected Serial Heterojunction Array of Co3 O4 /Cux O/Foam Cu Assembled via Layer upon Layer Oxidation

The foam copper (FCu) has been first used as a promising supporting material to prepare a photo-activated catalyst of Co₃ O₄ /Cu_x O/FCu, in which the fine Co₃ O₄ particles are inlayed on the Cu_x O nanowires to form a Z-type heterojunction array connected by substrate Cu. The prepared samples have been used as a photo-activated catalyst to directly decompose gaseous benzene and the optimized Co₃ O₄ /Cu_x O/FCu demonstrates a 99.5% removal efficiency and 100% mineralizing rate within 15 min in benzene concentration range from 350 to 4000 ppm under simulate solar light irradiation. To track the reactive mechanism, a series of MO_x /Cu_x O/FCu (M = Mn, Fe, Co, Ni, Cu, Zn) is prepared and a novel photo-activated direct catalytic oxidation route is proposed based on the comparative investigation of material properties. Moreover, the approach grew in situ via layer upon layer oxidation on FCu dedicates to the extra lasting reusability and the easy accessibility in the diverse situations. This work provides a novel strategy for the preparation of Cu connected series multidimensional heterojunction array and a promising application for the quick abatement of the high-leveled concentration gaseous benzene and its derivatives from the industrial discharged flow or the accident scene's leakage.

Fungal bioproducts for petroleum hydrocarbons and toxic metals remediation: recent advances and emerging technologies

Petroleum hydrocarbons and toxic metals are sources of environmental contamination and are harmful to all ecosystems. Fungi have metabolic and morphological plasticity that turn them into potential prototypes for technological development in biological remediation of these contaminants due to their ability to interact with a specific contaminant and/or produced metabolites. Although fungal bioinoculants producing enzymes, biosurfactants, polymers, pigments and organic acids have potential to be protagonists in mycoremediation of hydrocarbons and toxic metals, they can still be only adjuvants together with bacteria, microalgae, plants or animals in such processes. However, the sudden accelerated development of emerging technologies related to the use of potential fungal bioproducts such as bioinoculants, enzymes and biosurfactants in the remediation of these contaminants, has boosted fungal bioprocesses to achieve higher performance and possible real application. In this review, we explore scientific and technological advances in bioprocesses related to the production and/or application of these potential fungal bioproducts when used in remediation of hydrocarbons and toxic metals from an integral perspective of biotechnological process development. In turn, it sheds light to overcome existing technological limitations or enable new experimental designs in the remediation of these and other emerging contaminants.

Systematic comparison of a biotrickling filter and a conventional filter for the removal of a mixture of hydrophobic VOCs by Candida subhashii

This work systematically compared the potential of a conventional fungal biofilter (BF) and a fungal biotrickling filter (BTF) for the abatement of a mixture of hydrophobic volatile organic compounds (VOCs). Candida subhashii was herein used for the first time, to the best of the author's knowledge, to remove n-hexane, trichloroethylene, toluene and α-pinene under aerobic conditions. C. subhashii immobilized on polyurethane foam supported steady state removal efficiencies of n-hexane, trichloroethylene, toluene and α-pinene of 25.4 ± 0.9%, 20.5 ± 1.0%, 19.6 ± 1.5% and 25.6 ± 2.8% in the BF, and 35.7 ± 0.9%, 24.0 ± 1.6%, 44.0 ± 1.7% and 26.2 ± 1.8% in the BTF, respectively, at relatively short gas residence times (30 s). The ability of C. subhashii to biodegrade n-hexane, TCE, toluene and α-pinene was confirmed in a batch test conducted in serum bottles, where a biodegradation pattern (toluene ≈ n-hexane > α-pinene > trichloroethylene) comparable to that recorded in the BF and BTF was recorded.

Simulation of the Biofiltration of Sulfur Compounds: Effect of the Partition Coefficients

The effect of the partition coefficient on the simulation of the operation of a biotrickling filter treating a mixture of sulfur compounds was analyzed to evaluate the pertinence of using Henry’s law in determining its removal capacity. The analysis consisted of the simulation of a biotrickling filter that bio-oxides hydrogen sulfide (H2S), dimethyl sulfide (DMS), methyl mercaptan (MM) and dimethyl disulfide (DMDS) using different types of models for determining the partition coefficient: Henry’s law for pure water, Henry’s law adjusted from experimental data, a mixed model (Extended UNIQUAC) and a semi-empirical model of two-parameters. The simulations were compared with experimental data. It was observed that Henry’s law for pure water could produce significant deviations from empirical data due to the liquid phase not being pure water. The two-parameter model better fits with similar results compared to the extended UNIQUAC model, with a lower calculation cost and necessary parameter amount. It shows that semi-empirical models can considerably improve simulation accuracy where complex phase interactions are present.

Air Pollutants Removal Using Biofiltration Technique: A Challenge at the Frontiers of Sustainable Environment

Air pollution is a central problem faced by industries during the production process. The control of this pollution is essential for the environment and living organisms as it creates harmful effects. Biofiltration is a current pollution management strategy that concerns removing odor, volatile organic compounds (VOCs), and other pollutants from the air. Recently, this approach has earned vogue globally due to its low-cost and straightforward technique, effortless function, high reduction efficacy, less energy necessity, and residual consequences not needing additional remedy. There is a critical requirement to consider sustainable machinery to decrease the pollutants arising within air and water sources. For managing these different kinds of pollutant reductions, biofiltration techniques have been utilized. The contaminants are adsorbed upon the medium exterior and are metabolized to benign outcomes through immobilized microbes. Biofiltration-based designs have appeared advantageous in terminating dangerous pollutants from wastewater or contaminated air in recent years. Biofiltration uses the possibilities of microbial approaches (bacteria and fungi) to lessen the broad range of compounds and VOCs. In this review, we have discussed a general introduction based on biofiltration and the classification of air pollutants based on different sources. The history of biofiltration and other mechanisms used in biofiltration techniques have been discussed. Further, the crucial factors of biofilters that affect the performance of biofiltration techniques have been discussed in detail. Finally, we concluded the topic with current challenges and future prospects.

Optimization and Purification of Terpenyl Flavor Esters Catalyzed by Black Cumin (Nigella sativa) Seedling Lipase in Organic Media

Geranyl butyrate and citronellyl butyrate esters are industrially important fruity flavors that are being used in food and as a fragrance in cosmetics. Previously terpenyl fruity flavors have been successfully synthesized in organic solvents using crude seedlings enzymes. The purpose of the current study was to standardize reaction parameters for the optimal synthesis of geranyl butyrate using the best chosen black cumin seedling lipase in an organic medium through direct esterification reactions. Geranyl butyrate and citronellyl butyrate esters were identified, quantified through gas chromatography, confirmed through GC-MS, and partiallypurified through the distillation process. Effect of organic solvents (acetonitrile, n-hexane, pentane, heptane, and toluene), alcohol and acid concentrations (0.125–0.3 M), temperature (20–50°C), incubation time (1–72 h), and enzyme concentrations (0.05–0.3 g) were studied on the synthesis of geranyl butyrate using black cumin seedling lipase. The highest conversion yields of ester (96%) were obtained when 0.25 M of geraniol and butyric acid were reacted at 37°C for 48 h in the presence of 0.25 g of crude seedling lipase enzyme in n-hexane. It was concluded that the germinated black cumin seedling lipase proved to be the best among the selected biocatalysts for the synthesis of geranyl butyrate in n-hexane.

Pentane Depletion by a Surface DBD and Catalysis Processing

We study pentane depletion using a hybrid plasma system based on a surface dielectric barrier discharge (SDBD), with and without a catalyst, and as a function of plasma power and alkane concentration. We evaluate pentane decomposition efficiency based on plasma power and quantify the role of the catalyst in the resulting depletion of intermediate products. Analyses of the temporal evolution of pentane and the intermediate decomposition products allow us to estimate the corresponding decomposition rates according to the plasma parameters. We find that depletion efficiency increases as a function of pentane concentration. Furthermore, it is shown that the catalytic processes are responsible for a significant increase in the depletion rates of the intermediate reaction products, thus contributing to the total abatement process of pentane.

Modelling botanical biofiltration of indoor air streams contaminated by volatile organic compounds

Botanical filtration is a biological-based treatment method suitable for removing hazardous volatile organic compounds (VOCs) from air streams, based on forcing an air flow through a porous substrate and foliage of a living botanical compartment. The pathways and removal mechanisms during VOC bioremediation have been largely investigated; however, their mathematical representation is well established only for the non-botanical components of the system. In this study, we evaluated the applicability of such a modelling scheme to systems which include a botanical compartment. We implemented a one-dimensional numerical model and performed a global sensitivity analysis to measure the input parameters influence on the transient and steady biofilter responses. We found that the most sensitive parameters on the transient-state behaviour were the mass transfer coefficient between gas and solid surfaces, and the fraction of solid surfaces covered by the biofilm; the steady-state response was primarily influenced by the biofilm specific surface area and the fraction of surfaces covered by the biofilm. We calibrated the identified set of parameters and successfully validated the model against data from a pilot-scale installation. The results showed that the application of the model to systems with a botanical compartment is feasible, although under a strict set of assumptions.

Screening and study of the degradation characteristics of efficient toluene degrading bacteria combinations

In this paper, three effective toluene-degrading bacteria were obtained through acclimation and screening by using landfill leachate as the initial liquid strain. The three obtained bacteria were denoted as J1, J2 and J3, and identified as Pseudomonas, Bacillus and Staphylococcus, respectively. We then identified the optimal combination of these toluene-degrading bacteria in the laboratory. The combination of J1 + J3 (1:1) exhibited the highest toluene removal efficiency (RE). A vertical bio-trickling filter (BTF) packed with ceramsite was started by inoculation with the effective combination. The performance of the BTF in treating toluene under various operating conditions was investigated. After 17 days of operation, the toluene RE reached about 90% and the maximum elimination capacity reached 42.0 g m^-3 h^-1. The scanning electron microscope (SEM) showed that after the successful start-up of the BTF, the biofilm on the packing surface primarily consisted of Bacillus and Staphylococcus. During the stable state, the RE of the BTF was maintained above 80%, the shortest empty bed residence time was 34 s and toluene concentrations ranged between 300 and 800 mg m^-3. The results indicate that the BTF started using the effective combination of bacteria described here is robust. This paper also provides a preliminary analysis of the mechanism of microbial degradation of pollutants in the BTF.

Water condition in biotrickling filtration for the efficient removal of gaseous contaminants

Biofiltration (BF) facilitates the removal of organic and inorganic compounds through microbial reactions. Water is one of the most important elements in biotrickling filters that provides moisture and nutrients to microbial biofilms. The maintenance of proper trickle watering is very critical in biotrickling filtration because the flow rate of the trickling water significantly influences contaminant removal, and its optimal control is associated with various physicochemical and biological mechanisms. The lack of water leads to the drying of the media, creating several issues, including the restricted absorption of hydrophilic contaminants and the inhibition of microbial activities, which ultimately deteriorates the overall contaminant removal efficiency (RE). Conversely, an excess of water limits the mass transfer of oxygen or hydrophobic gases. In-depth analysis is required to elucidate the role of trickle water in the overall performance of biotrickling filters. The processes involved in the treatment of various polluted gases under specific water conditions have been summarized in this study. Recent microscopic studies on biofilms were reviewed to explain the process by which water stress influences the biological mechanisms involved in the treatment of hydrophobic contaminated gases. In order to maintain an effective mass transfer, hydrodynamic and biofilm conditions, a coherent understanding of water stress and the development of extracellular polymeric substances (EPS) in biofilms is necessary. Future studies on the realistic local distribution of hydrodynamic patterns (trickle flow, water film thickness, and wet efficiency), integrated with biofilm distributions, should be conducted with respect to EPS development.

Performance and substance transformation of low-pH and neutral-pH biofilters treating complex gases containing hydrogen sulfide, ammonia, acetic acid, and toluene

Two biofilters with low pH and neutral pH were operated on pilot scale for the treatment of complex gases containing hydrogen sulfide, ammonia, acetic acid, and toluene during 205 days. Under the coexistence of complex gases, the low-pH biofilter (LPB) had higher removal efficiency (RE) for hydrogen sulfide and toluene, and the maximum efficiencies were 99.24% and 99.90% respectively, while the neutral-pH biofilter (NPB) had higher REs of ammonia and acetic acid, up to 99.90% and 99.92% respectively. Higher pressure drop up to 622 Pa was achieved in the LPB, most likely caused by the special structure of fungi different from bacteria. Determination of the concentration of carbon-based intermediates revealed the dominant microbial removal of acetic acid and clarified the relationship between the generation of intermediate and the performance of biofilters. Respective amount of CO2 in the inlet and outlet showed that the mineralization capacity of the NPB was higher than that of the LPB, and it was more influenced by empty bed residence time (EBRT). The proportion of different forms of nitrogen and sulfur in the filler indicated that the removal of ammonia in the LPB mainly depended on the adsorption by moisture, while that in the NPB was microbial degradation, which was also the main removal pathway of sulfur regardless of pH condition. The removal and transformation of different substances in coexisting complex gases showed different characteristics in the LPB and NPB respectively.

Effects of filler voidage on pressure drop and microbial community evolution in fungal bio-trickling filters

Bio-trickling filters (BTFs) can be used to remediate pollution by volatile organic compounds such as toluene. To investigate the effect of filler voidage on pressure drop (△P), two parallel BTFs were constructed using ceramsite with different voidages (47.5% for BTF1 and 55% for BTF2) and inoculated with Fusarium fungus to purify toluene. Commutation and stagnation operations were explored as ways to relieve △P. In BTF1, commutation temporarily relieved △P and maintained it for 7 days. Implementing stagnation on the 178th day for 69 days effectively reduced the △P from 720 Pa/m to below 20 Pa/m, which was maintained for 36 days. Compared with BTF1, the filler in BTF2 effectively delayed the increase in △P for 70 days or more and ensured stable operation for as long as 174 days. High-throughput sequencing revealed that Fusarium was mainly replaced by Protoctista, Fronsecaea and other fungi in both BTFs, although there were significant differences in their microbial communities. The influences of commutation and stagnation operations on fungal evolution were more obvious in BTF2, in relation to both time and space. The results provide guidance for designing better BTFs to treat hazardous pollutants.

Biological-based methods for the removal of volatile organic compounds (VOCs) and heavy metals

The current scenario of increased population and industrial advancement leads to the spoliation of freshwater and tapper of the quality of water. These results decrease in freshwater bodies near all of the areas. Besides, organic and inorganic compounds discharged from different sources into the available natural water bodies are the cause of pollution. The occurrence of heavy metals in water and volatile organic compounds (VOCs) in the air is responsible for a vast range of negative impacts on the atmosphere and human health. Nonetheless, high uses of heavy metals for human purposes may alter the biochemical and geochemical equilibrium. The major air contaminants which are released into the surroundings known as VOCs are produced through different kinds of sources, such as petrochemical and pharmaceutical industries. VOCs are known to cause various health hazards. VOCs are a pivotal group of chemicals that evaporate readily at room temperature. To get over this problem, biofiltration technology has been evolved for the treatment of heavy metals using biological entities such as plants, algae, fungi, and bacteria. Biofiltration technology is a beneficial and sustainable method for the elimination of toxic pollutants from the aquatic environment. Various types of biological technologies ranging from biotrickling filters to biofilters have been developed and they are cost-effective, simple to fabricate, and easy to perform. A significant advantage of this process is the pollutant that is transformed into biodegradable trashes which can decompose within an average time period, thus yielding no secondary pollutants. The aim of this article is to scrutinize the role of biofiltration in the removal of heavy metals in wastewater and VOCs and also to analyze the recent bioremediation technologies and methods.

Enhanced photocatalytic degradation of gaseous toluene and liquidus tetracycline by anatase/rutile titanium dioxide with heterophase junction derived from materials of Institut Lavoisier-125(Ti): Degradation pathway and mechanism studies

Anatase/rutile titanium dioxide (TiO₂) with heterophase junction and large Brunauer-Emmett-Teller (BET) specific surface area (50.1 m² g^-1) is successfully synthesized by calcinating Materials of Institut Lavoisier-125(Ti) (MIL-125(Ti)) with 30% O₂/Ar at the temperature of 600 °C (M-O-600). Several techniques are used to examine the physicochemical, photoelectrochemical and optical properties of samples, and their photocatalytic performances are evaluated by photodegradation of gaseous toluene and liquidus tetracycline (TC) under visible light illumination. It is found that the calcination temperature has significant influence on the crystal structure and physicochemical parameters of TiO₂. The weight fractions of rutile and anatase TiO₂ of M-O-600 are approximately 0.7 and 0.3, which displays outstanding photocatalytic activity. Through the construction of heterophase junction, M-O-600 has better oxygen adsorption and higher density of localized states, which effectively promotes the generation of superoxide radical (·O₂^-) and hydroxyl radical (·OH) species. In-situ infrared spectra indicate that toluene is oxidized to benzyl alcohol, benzaldehyde and benzoic acid in turn and then oxidized to formic acid and acetic acid before eventually degraded into H₂O and CO₂. Gas chromatography-mass spectrometry (GC-MS) is also used to further investigate the degradation pathway of toluene. Degradation pathway and mechanism of TC are studied by liquid chromatography-tandem mass spectrometry (LC-MS). Moreover, three-dimensional excitation-emission matrix fluorescence spectroscopy (3D EEMs) and total organic carbon (TOC) show that TC can be effectively mineralized through a series of reactions by M-O-600 during photocatalysis.

Styrene removal with an acidic biofilter with four packing materials: Performance and fungal bioaerosol emissions

The packing material used in acidic biofilters (ABFs) has a significant impact on styrene removal. The bioaerosol emission was rarely considered when evaluating the packing materials in the ABFs. Four ABFs packed with ceramsite, compost, lava and polyurethane (PU) were developed and compared for their styrene removal and fungal bioaerosol emissions characteristics over 529 days. The removal efficiencies of styrene in the ABFs were higher under the condition of longer empty bed residence time (EBRT) and lower inlet concentration. The maximum styrene elimination capacities of the ABFs with ceramsite, compost, lava and PU were 74.57, 87.81, 67.13 and 101.88 g/m³ h, respectively. A lower pressure drop and the highest fungi count were observed in the ABF packed with PU. The emissions concentrations of fungal bioaerosols at the humidity of 63.5% were lower than those at a humidity of 42.7% and it increased with the air velocity. Additionally, the concentrations of fungal bioaerosols emitted from the ABFs packed with PU were 2168 ± 145-3661 ± 257 CFU/m³, which was 33%-90% lower than those of the other three ABFs. The particle size distributions of the fungal bioaerosols emitted from the ABFs packed with PU and compost were mainly centered around large particles. Considering the removal of styrene and the fungal bioaerosols emissions, PU was the optimal packing material for ABF.

Performance and fungal diversity of bio-trickling filters packed with composite media of polydimethylsiloxane and foam ceramics for hydrophobic VOC removal

Bio-trickling filters (BTFs) can be used for the treatment of hydrophobic VOC-contaminated air. To improve treatment performance, two novel polydimethylsiloxane (PDMS) packing media were produced and trialled in BTFs inoculated with Cladophialophora fungus. The BTF packed with PDMS/foam ceramic composite filler showed superior performance: rapid start-up within 3 days, rapid restart within 7 days after starvation for 1 month, a maximum toluene elimination capacity (EC) of 264.4 g m^-3·h^-1 at an empty bed residence time of 10 s, and a pressure drop that was controllable by adjusting the nutrient supply regime. High-throughput sequencing was used to analyse the effect of spatial position on the microbial communities in the top and bottom filler layers. Meanwhile, by investigating the EC in the vertical direction of the BTF, spatial heterogeneity in the fungal degradation of a hydrophobic VOC was preliminarily explored.

Effect of hydrophobic fumed silica addition on a biofilter for pentane removal using SIFT-MS

Biofiltration is a typical air pollution control process for the treatment of volatile organic compounds (VOCs). Mass transfer of hydrophobic VOCs to the biofilm is limited which leads to low removal efficiency (RE). Aiming to enhance the transport of hydrophobic VOCs, the effect of hydrophobic fumed silica (HFS) addition to a biofilter (BF) for pentane removal was studied in this paper. The effect of HFS on pentane removal was evaluated by daily RE measurements and periodical headspace gas pentane pulse injections using SIFT-MS as analysis apparatus. The BF was operated during more than 100 days at an empty bed residence time (EBRT) of 120 s reaching an elimination capacity (EC) up to 93.8 g pentane m^-3 h^-1. At the last stage of the study, when a higher nutrient pulse and HFS to a concentration of 1.5% w/w wet were added, the BF showed better EC (46.3 ± 14.9 g pentane m^-3 h^-1; RE = 96.2%) compared to the previous stages (28.3 ± 4.4 g pentane m^-3 h^-1; RE = 68.3%). This overall performance improvement was in line with the short peak perturbation experiments carried out during the operational time which demonstrated, by net retention time (NRT) determination, to be a fast and reliable tool to gain insights into the behaviour of pollutants inside the BF and its state. Pentane demonstrated to have larger interactions with the packing material when HFS was added. NRT/EBRT ratio variated along the whole operational time, being larger at the last stage.

Progressing Climate Changes and Deteriorating Air Quality as One of the Biggest Challenges of Sustainable Development of the Present Decade in Poland

Among the biggest challenges facing our civilization is slowing down the rate of climate change and improving air quality in cities. This cannot be achieved in isolation from the sustainability and intensification of relevant research. The aim of this Special Issue: Current Trends in Emission Control and Forecasting of Air Quality and Climate Changes is to publish selected high-quality papers from the 15th Scientific Conference POL-EMIS 2020: Current Trends in Air and Climate Protection—Control Monitoring, Forecasting, and Reduction of Emissions (19–21 October 2020, Wroclaw) and other papers related to the development of: low-emission fuels, industrial technologies, and energy generation, including renewable energy sources (RES); technology for reducing/eliminating emissions from low municipal sources and transport; innovative methods of waste gas purification; emission and immission control methods (including odors); prospective ways of counteracting climate change; indoor air protecting methods; development of mathematical modeling of air quality; new directions in forecasting the effects of air pollution and climate change and air quality management.

Photocatalytic effect of addition of TiO2 to acrylic-based paint for passive toluene degradation

Volatile organic compounds (VOCs) are known to be hazardous and associated with several human health problems. Thus, many technologies have been developed in recent years for their removal, such as thermal catalysis, photocatalysis and ozonization. In this study, the main objective was to evaluate the effects of incorporating titanium dioxide into an acrylic-based paint for gaseous toluene abatement. Paints with photocatalytic properties were prepared by adding TiO₂ P25 powder to an acrylic-based paint, using the following proportions: 0, 10, 15, 20 and 50 wt% (dry basis). Toluene and CO₂ concentrations at the reactor input and output were determined using GC/MS, and GC/FID, respectively, and the toluene conversion and CO₂ formation were assessed. The compounds adsorbed onto photocatalytic paints were extracted and then identified by GC/MS. The results indicated that the addition of 50 wt% of TiO₂ P25 results in a paint of reduced quality. The addition of 20 wt% of TiO₂ P25 to the paint led to higher values for the photocatalytic conversion of toluene to CO₂. The occurrence of two simultaneous processes was observed: the photocatalytic oxidation of toluene to CO₂ and the self-degradation of the organic compounds, such as polymeric acrylic, in the paint. The adsorption of different compounds onto the photocatalytic paints was identified by GC/MS analysis. The use of photocatalytic paints is a promising technique for toluene abatement, but it requires further study and improvement particularly with regard to the effects of the self-degradation of the paint.

Computational tomography and CFD simulation of a biofilter treating a toluene, formaldehyde and benzo[α]pyrene vapor mixture

In this work, a 3D computational tomography (CT) of the packing material of a laboratory column biofilter is used to model airflow containing three contaminants. The degradation equations for toluene, formaldehyde and benzo[α]pyrene (BaP), were one-way coupled to the CFD model. Physical validation of the model was attained by comparing pressure drops with experimental measurement, while experimental elimination capacities for the pollutants were used to validate the biodegradation kinetics. The validated model was used to assess the existence of channeling and to predict the impact of the three-dimensional porous geometry on the mass transfer of the contaminants in the gas phase. Our results indicate that a physically meaningful simulation can be obtained using the techniques and approach presented in this work, without the need of performing experiments to obtain macroscopic parameters such as gas-phase axial and radial dispersion coefficients and porosities.

Fungal elimination of toluene vapor in one- and two-liquid phase biotrickling filters: Effects of inlet concentration, operating temperature, and peroxidase enzyme activity

In this study, performance of biotrickling filters (BTFs) inoculated with fungus Phanerochaete chrysosporium at 30 °C and 40 °C in the absence and presence of silicone oil (10% v/v) was investigated. Removal of toluene was carried out at empty bed residence time (EBRT) of 1 min and at inlet concentrations of 0.5-4.4 g m^-3 and 0.5-24.7 g m^-3 for one-liquid phase (OLP-BTF) and two-liquid phase BTF (TLP-BTF), respectively. In general, at 40 °C, removal efficiencies (REs) > 80% were obtained in OLP-BTF for the inlet toluene concentrations < 2.5 g m^-3, and REs > 70% were obtained for concentrations < 18 g m^-3 in TLP-BTF. Based on the balanced equation for biodegradation, fungal respiration produced more CO₂ in OLP-BTF (1.38 mol CO₂/mole toluene) in comparison to TLP-BTF (0.67 mol CO₂/mole toluene). In other words, the presence of oil enhanced microbial growth due to the increase of hydrophobic substrate bioavailability. The activity of extracellular ligninolytic manganese peroxidase (MnP) enzyme produced by the fungal culture was detected in the range of 27.6-71.6 U L^-1 (μmol min^-1 L^-1) at 40 °C in TLP-BTF, while no enzymatic activity was detected in OLP-BTF.

Effects of n-butanol presence, inlet loading, empty bed residence time and starvation periods on the performance of a biotrickling filter removing cyclohexane vapors from air

This paper presents the results of investigations on the removal of cyclohexane vapors from air using a peat-perlite packed biotrickling filter. Effects of basic process parameters i.e. inlet loading and empty bed residence time as well as introduction of n-butanol to the treated air stream and starvation periods on the process performance were evaluated. The results show that the introduction of hydrophilic n-butanol results in an enhanced removal of hydrophobic cyclohexane comparing to the experiments where only cyclohexane was treated. Additionally, the biotrickling filter performance after the starvation events is regained to more extent for mixed system than for the single cyclohexane. A novel and interesting element of the paper is the application of an electronic nose for the process monitoring. Obtained results are discussed in the perspective of an influence of the presence of a compound with different affinity to aqueous phase on the removal efficiency of the compound with opposite chemical properties.

The impact of environmental parameters on the conversion of toluene to CO2 and extracellular polymeric substances in a differential soil biofilter

The fraction of pollutant converted to CO₂ versus biomass in biofiltration influences the process efficacy and the lifetime of the bed due to pressure drop increases. This work determined the relative quantitative importance and potential interactions between three critical environmental parameters: toluene concentration (Tol), matric potential (ψ) and temperature (T) on % CO₂, elimination capacity (EC) and the production rate of non-CO₂ products. These parameters are the most variable in typical biofilter operation. The data was fit to a non-linear model of the form y=a(Tol)^bT^cψ^d. A rigorous carbon balance (100.5 ± 7.0%) tracked the fate of degraded toluene as CO₂ and non-CO₂ carbon endpoints. The % CO₂ mineralization varied from (34-91%) with environmental parameters: temperature (20-40 °C), matric potential, (-10 to -100 cm_H2O) and residual toluene, (20-180 ppm). The highest conversion to CO₂ was at the wettest conditions (-10 cm_H2O) and lowest residual toluene concentration (18 ppm). Matric potential had twice the impact of toluene concentration on % CO₂, while temperature had less impact. The elimination capacity varied from 11 to 50 g_C⋅m^-3h^-1 and was highest at 40 °C, the wettest conditions with limited impact by toluene concentrations. Temperature increased the EC and non-CO₂ production rates strongly while matric potential and toluene concentration had less influence (4x - 10x less). This study illustrated the quantitative significance and simultaneous interaction between critical environmental parameters on carbon endpoints and biofilter performance. This kind of multivariable parameter study provides valuable insights which can address performance and clogging issues in biofilters.

Enhancement of using combined packing materials on the removal of mixed sulfur compounds in a biotrickling filter and analysis of microbial communities

Background

Packing materials is a critical design consideration when employing biological reactor to treat malodorous gases. The acidification of packing bed usually results in a significant drop in the removal efficiency. In the present study, a biotrickling filter (BTF2) packed with plastic balls in the upper layer and with lava rocks in the bottom layer, was proposed to mitigate the acidification.

Results

Results showed that using combined packing materials efficiently enhanced the removal performance of BTF2 when compared with BTF1, which was packed with sole lava rocks. Removal efficiencies of more than 92.5% on four sulfur compounds were achieved in BTF2. Average pH value in its bottom packing bed was about 4.86, significantly higher than that in BTF1 (2.85). Sulfate and elemental sulfur were observed to accumulate more in BTF1 than in BTF2. Analysis of principal coordinate analysis proved that structure of microbial communities in BTF2 changed less after the shutdown but more when the initial pH value was set at 5.5. Network analysis of significant co-occurrence patterns based on the correlations between microbial taxa revealed that BTF2 harbored more diverse microorganisms involving in the bio-oxidation of sulfur compounds and had more complex interactions between microbial species.

Conclusions

Results confirmed that using combined packing materials effectively improved conditions for the growth of microorganisms. The robustness of reactor against acidification, adverse temperature and gas supply shutdown was greatly enhanced. These provided a theoretical basis for using mixed packing materials to improve removal performance.

Comparative Evaluation of Selected Biological Methods for the Removal of Hydrophilic and Hydrophobic Odorous VOCs from Air

Due to increasingly stringent legal regulations as well as increasing social awareness, the removal of odorous volatile organic compounds (VOCs) from air is gaining importance. This paper presents the strategy to compare selected biological methods intended for the removal of different air pollutants, especially of odorous character. Biofiltration, biotrickling filtration and bioscrubbing technologies are evaluated in terms of their suitability for the effective removal of either hydrophilic or hydrophobic VOCs as well as typical inorganic odorous compounds. A pairwise comparison model was used to assess the performance of selected biological processes of air treatment. Process efficiency, economic, technical and environmental aspects of the treatment methods are taken into consideration. The results of the calculations reveal that biotrickling filtration is the most efficient method for the removal of hydrophilic VOCs while biofilters enable the most efficient removal of hydrophobic VOCs. Additionally, a simple approach for preliminary method selection based on a decision tree is proposed. The presented evaluation strategies may be especially helpful when considering the treatment strategy for air polluted with various types of odorous compounds.