Effects of partial gelatinization on structure and thermal properties of corn starch after spray drying

Hot air-assisted radio frequency drying of corn kernels: the effect on structure and functionality properties of corn starch

Hot air (HA) drying caused quality damage of grains with long treatment time. Radio frequency (RF) heating as an emerging technology was applied to improve drying quality of cereals effectively. The effects of HA-RF drying (50 °C, 70 °C, 90 °C) of corn kernels on the morphology, structure, and physicochemical properties of starch were investigated and compared with HA drying. The surface of treated starch became rough, along with fragments and pores. Drying treatments increased the amylose content from 10.59 % to 23.88 % and the residual protein content of starch from 0.58 % to 1.23 %, and reduced the crystallinity from 31.95 % to 17.15 % and short-range order structures of starch from 0.918 to 0.868. The change of structures in turn resulted in the increase of pasting viscosity, gelatinization temperature, storage modulus and loss modulus. Furthermore, the HA-RF dried starch displayed stronger thermal stability, higher gelatinization degree and better gelation properties than the HA-treated starch at the same temperature. The data proved that the synergistic effects of HA and RF were more effective in modulating the starch structure and improving the functional characteristics of corn starch. This paper would like to provide potential reference for better application of HA-RF technologies to corn.

Comparative analysis of multi-angle structural alterations and cold-water solubility of kudzu starch modifications using different methods

Kudzu, a plant known for its medicinal value and health benefits, is typically consumed in the form of starch. However, the use of native kudzu starch is limited by its high pasting temperature and low solubility, leading to a poor consumer experience. In this study, kudzu starch was treated using six modification techniques: ball milling, extrusion puffing, alcoholic-alkaline, urea-alkaline, pullulanase, and extrusion puffing-pullulanase. The results of the Fourier transform infrared spectrum showed that the intensity ratio of 1047/1022 cm-1 for the modified starches (1.02-1.21) was lower than that of the native kudzu starch (1.22). The relative crystallinity of modified kudzu starch significantly decreased, especially after ball milling, extrusion puffing, and alcoholic-alkaline treatment. Furthermore, scanning electron microscopy and confocal laser scanning microscopy revealed significant changes in the granular structures of the modified starches. After modification, the pasting temperature of kudzu starch decreased (except for the urea-alkaline treatment), and the apparent viscosity of kudzu starch decreased from 517.95 Pa·s to 0.47 Pa·s. The cold-water solubility of extrusion-puffing and extrusion puffing-pullulanase modified kudzu starch was >70 %, which was significantly higher than that of the native starch (0.11 %). These findings establish a theoretical basis for the potential development of instant kudzu powder.

Physicochemical properties of amorphous granular starch (AGS) prepared by non-thermal gelatinization by high hydrostatic pressure (HHP) and spray drying

Corn starch was gelatinized by high hydrostatic pressure (HHP) and spray drying to make amorphous granular starch (AGS), and their physicochemical properties were compared with the conventionally prepared (heat-gelatinized and spray dried) AGS to devise a novel AGS preparation methodology. Pressure-induced (PAGS) and heat-induced AGS (HAGS) maintained their granular shape but lost their birefringence indicating that both methods could prepare AGS. DSC (differential scanning calorimeter) and XRD (X-ray diffraction) analysis confirmed the complete loss of amylopectin double helices and crystallinity of both PAGS and HAGS. However, their swelling power, solubility, RVA pasting properties, acid/shear stability, gel forming ability and textural properties were completely different. PAGS exhibited constrained swelling, suppressed amylose leaching, and reduced viscosity. Notably, HAGS formed a gel without heating, whereas PAGS yielded a viscous paste with water-soluble attributes. Even after reheating, PAGS maintained its granular structure with comparably less swelling and weaker gel strength than HAGS. Consequently, newly developed PAGS exhibited distinctive characteristics compared to the conventional HAGS, such as lower solubility and swelling power, viscosity, textural properties, and high acid and shear stabilities, rendering it a viable option for various applications within the food industry.

Effects of Extrusion Technology on Physicochemical Properties and Microstructure of Rice Starch Added with Soy Protein Isolate and Whey Protein Isolate

In order to improve the retrogradation of rice starch (RS) and the quality of rice products, soy protein isolate (SPI), whey protein isolate (WPI), and rice flour were mixed and further extruded into mixed flour. The physicochemical properties and morphology of starch of extruded rice flour (ERS) and starch of extruded mixtures of SPI, WPI, and rice flour (SPI-WPI-ERS) were analyzed. The distribution of amylopectin chain length, molecular weight, microstructure, crystallinity, short-range ordered structure, pasting properties, and thermodynamic properties of RS, ERS, and SPI-WPI-ERS were measured. The results showed that, compared with rice starch, the proportion of long-chain starch, total starch content, and molecular weight were decreased in ERS and SPI-WPI-ERS, but the proportion of short-chain and amylose content was increased. The short-range order structure was destroyed. The water absorption of ERS and SPI-WPI-ERS was much higher than rice starch at 55 °C, 65 °C, and 75 °C, but lower than that of rice starch at 95 °C. Therefore, the retrogradation characteristics of SPI-WPI-ERS were improved. The setback of rice starch products was reduced and the setback of SPI-WPI-ERS was lower than that of ERS. Overall, the retrogradation of rice starch was delayed by adding exogenous protein and extrusion technology, and the application range of rice flour in staple food products was broadened.

Effect of Ball-Milling on Starch Crystalline Structure, Gelatinization Temperature, and Rheological Properties: Towards Enhanced Utilization in Thermosensitive Systems

Starch's crystalline structure and gelatinization temperature might facilitate or hinder its use. Ball milling has frequently been mentioned in the literature as a method for reducing starch size and as a more environmentally friendly way to change starch, such as by increasing surface area and reactivity, which has an impact on other starch properties. In this study, starch samples were milled for varying durations (1, 5, 10, 20, and 30 h) and at different starch-to-ball mass ratios (1:6 and 1:20). Microscopy and XRD revealed that prolonged milling resulted in effective fragmentation and a decrease in crystallinity of the starch granules. Increasing milling times resulted in an increase in amylose content. Rheology and thermal studies revealed that gelatinization temperatures dropped with milling duration and that viscosity and thixotropy were directly influenced. The samples milled for 10, 20, and 30 h at a ratio of 1:20 were the most fragmented and upon drying formed a transparent film at ambient temperature, because of the lower gelatinization temperature. Starch ball milling could lead to the use of this material in thermosensitive systems.

Characteristics of physically modified starches

Starch is an abundant natural, non-toxic, biodegradable polymer. Due to its low price, it is used for various purposes in various fields such as the cosmetic, paper, and construction industries as well as the food industry. Due to recent consumer interest in clean label materials, physically modified starch is attracting attention. Manufacturing methods of physically modified starch include pregelatinization, hydrothermal treatment such as heat moisture treatment and annealing, hydrostatic pressure treatment, ultrasonic treatment, milling, and freezing. In this study, toward development of clean label materials, manufacturing methods and characteristics of physically modified starches were discussed.

Individual or mixing extrusion of Tartary buckwheat and adzuki bean: Effect on quality properties and starch digestibility of instant powder

Introduction

Tartary buckwheat and adzuki bean, which are classified as coarse grain, has attracted increasing attention as potential functional ingredient or food source because of their high levels of bioactive components and various health benefits.

Methods

This work investigated the effect of two different extrusion modes including individual extrusion and mixing extrusion on the phytochemical compositions, physicochemical properties and in vitro starch digestibility of instant powder which consists mainly of Tartary buckwheat and adzuki bean flour.

Results

Compared to mixing extrusion, instant powder obtained with individual extrusion retained higher levels of protein, resistant starch, polyphenols, flavonoids and lower gelatinization degree and estimated glycemic index. The α-glucosidase inhibitory activity (35.45%) of the instant powder obtained with individual extrusion was stronger than that obtained with mixing extrusion (26.58%). Lower levels of digestibility (39.65%) and slower digestion rate coefficient (0.25 min^-1) were observed in the instant powder obtained with individual extrusion than in mixing extrusion (50.40%, 0.40 min^-1) by logarithm-of-slope analysis. Moreover, two extrusion modes had no significant impact on the sensory quality of instant powder. Correlation analysis showed that the flavonoids were significantly correlated with physicochemical properties and starch digestibility of the instant powder.

Discussion

These findings suggest that the instant powder obtained with individual extrusion could be used as an ideal functional food resource with anti-diabetic potential.

Particle filled protein-starch composites as the basis for plant-based meat analogues

Rapid swelling, high amylopectin starches including Thermally Inhibited (TI), Chemically Modified (CM), and Granular Cold- Swelling (GCS) were assessed for their supporting matrix forming potential and properties. Starches displayed identical calorimetric profiles with no endothermic events, and completely amorphous structure as judged by powder X-ray diffraction. However, they each provided different textural attributes. The starches were combined with pea protein isolate at a total concentration of 47%w/w (d.b.) to create a proteinacious supporting matrix. The starch protein matrix was then tested in a non-cold-set dough state as well as in a cold-set state after storage for 24h at 5^oC. In the non-cold-set state, hardness increased with the addition of protein. CM was the softest dough and was difficult to work with, while TI and GCS were harder, with TI having the greatest resilience. Once cold-set, the textural properties changed, and GCS was not able to form a solid structure, instead remaining a viscoelastic dough. The hardness and storage modulus (G') of TI and CM displayed a negative correlation with the addition of protein due to matrix disruption. However, the combination of TI starch and pea protein at a ratio of 70% starch and 30% protein in the dry fraction displayed a synergistic effect, with increased resilience, chewiness, and ductility. FTIR of TI starch and protein at the same 70:30 ratio provided further evidence for the existence of an interaction between pea protein and TI starch. The results support the use of TI rapid swelling starch and pea protein isolate as a supporting matrix for application in meat analogue systems.

An Insight into the Gelatinization Properties Influencing the Modified Starches Used in Food Industry: A review

Native starch is subjected to various forms of modification to improve its structural, mechanical, and thermal properties for wider applications in the food industry. Physical, chemical, and dual modifications have a substantial effect on the gelatinization properties of starch. Consequently, this review explores and compares the different methods of starch modification applicable in the food industry and their effect on the gelatinization properties such as onset temperature (To), peak gelatinization temperature (Tp), end set temperature (Tc), and gelatinization enthalpy (ΔH), studied using differential scanning calorimetry (DSC). Chemical modifications including acetylation and acid hydrolysis decrease the gelatinization temperature of starch whereas cross-linking and oxidation result in increased gelatinization temperatures. Common physical modifications such as heat moisture treatment and annealing also increase the gelatinization temperature. The gelatinization properties of modified starch can be applied for the improvement of food products such as ready-to-eat, easily heated or frozen food, or food products with longer shelf life.

Micronutrients encapsulation by starch as an enhanced efficiency fertilizer

Developing different paths to achieve sustainable agriculture is no longer an option; it is a necessity. EEF materials are alternatives to improve the efficacy of the agrochemicals in the soil and plant, reducing wasting and environmental contamination. The present work aims to develop EEF materials based on starch and micronutrients, considering few works address EEFs materials with micronutrients. Monoelementary dispersions of gelatinized starch with micronutrients (Fe, Cu, Mn) were spray-dried and thermally, structurally, and morphologically characterized. We evaluated water-medium nutrient release, release kinetics, and the swelling degree. Different micronutrients affect morphology, size distribution, swelling degree, release, kinetics, and interaction between polymer-nutrient. Bigger particle sizes achieved a higher swelling degree, which led to decreased micronutrient release in the water. The Peppas-Sahlin model mainly ruled the release kinetics (fitted to all the materials). This result confirmed our hypothesis that a swelling starch delays the release.

Physicochemical and Structural Characterization of Potato Starch with Different Degrees of Gelatinization

Starch gelatinization has been widely studied previously, but there is still a lack of systematical research on the relationship between the degree of starch gelatinization (DSG) and its physicochemical and structural properties. In this study, potato starch samples with DSG ranging from 39.41% to 90.56% were obtained by hydrothermal treatment. The thermal, rheological, and structural properties, as well as the water-binding capacity of samples were investigated. A starch solution with a DSG of 39.41% was partially sedimented at room temperature, while starch with a DSG of 56.11% can form a stable paste with a fine shear-thinning property, as well as samples with a DSG larger than 56.11%. The endothermic enthalpy, gelatinization range, and short-range ordered structure of starch were negatively correlated with DSG, whereas onset gelatinization temperature, apparent viscosity, and water-binding capacity were positively correlated. The viscoelasticity of starch gels was negatively correlated with the DSG after full gelatinization (DSG > 39.41%). Starch granules gradually lose their typical shape and less birefringence can be observed with increasing DSG. Hydrothermal treatment has a more significant effect on the amount of exposed hydroxyl groups than the ordered and amorphous structures of partially gelatinized starch. This study built linear correlations between starch physicochemical properties and the DSG and provided comprehensive insight into the characteristics of partially gelatinized potato starch.

Surfactant-Free Stabilization of Aqueous Graphene Dispersions Using Starch as a Dispersing Agent

Attention to graphene dispersions in water with the aid of natural polymers is increasing with improved awareness of sustainability. However, the function of biopolymers that can act as dispersing agents in graphene dispersions is not well understood. In particular, the use of starch to disperse pristine graphene materials deserves further investigation. Here, we report the processing conditions of aqueous graphene dispersions using unmodified starch. We have found that the graphene content of the starch-graphene dispersion is dependent on the starch fraction. The starch-graphene sheets are few-layer graphene with a lateral size of 3.2 μm. Furthermore, topographical images of these starch-graphene sheets confirm the adsorption of starch nanoparticles with a height around 5 nm on the graphene surface. The adsorbed starch nanoparticles are ascribed to extend the storage time of the starch-graphene dispersion up to 1 month compared to spontaneous aggregation in a nonstabilized graphene dispersion without starch. Moreover, the ability to retain water by starch is reduced in the presence of graphene, likely due to environmental changes in the hydroxyl groups responsible for starch-water interactions. These findings demonstrate that starch can disperse graphene with a low oxygen content in water. The aqueous starch-graphene dispersion provides tremendous opportunities for environmental-friendly packaging applications.

Physicochemical and digestive properties of A- and B-type granules isolated from wheat starch as affected by microwave-ultrasound and toughening treatment

In this study, the effect of microwave-ultrasound or/and toughening treatment on the physicochemical, structural properties, and in vitro digestibility of A- and B-type granules isolated from wheat starch were investigated. From the SEM, microwave-ultrasound and toughening treatment (MU-T) led to the appearance of irregular and disrupted structure significantly and an increment in the resistant starch content of A- and B-type granule. Furthermore, the MU-T starch possessed the lowest swelling power, light transmittance, and gelatinization temperature range (T_c -T_o) and the highest ΔH. After MU-T, the relative crystallinity (RC) of X-ray pattern, Fourier transform infrared ratio of 1047/1022 cm^-1, and the content of double helix and single helix of ¹³C CP/MAS NMR had increased significantly. In particular, there was a difference in the content of RS and SDS between A-starch granules and B-starch granules as well as their changes after modification (from 69.305% to 82.93 for A-starch and form 74.97% to 88.17 for B-starch, respectively), which was a similar trend with RC and helix content. This study indicated that, for both A-type granule and B-type granule starches, microwave-ultrasound and toughening treated samples had unique properties compared to singly modified starches.

Effect of high-temperatures and aqueous ethanol treatment on the formation process and properties of V-type Granular Starch (VGS)

Starch-water-ethanol mixtures were heated between 80 and 160 °C. The formation process of V-type granular starch (VGS) was investigated. DSC analysis showed that starch gelatinization was completely inhibited in 70 % ethanol. Microscopic analysis showed that starch remained granular morphology after modification, but when temperature exceeded 110 °C, Maltese cross and A-type crystalline structure disappeared, a V-type crystalline structure developed with increasing temperature, and short-range order of modified starch was reduced. It was indicated that VGS was formed at temperatures exceeding 110 °C in 70 % ethanol. When temperature was increased from 80 to 140 °C, starch cold-water viscosity increased from 17.00 cP to 1932.00 cP. Further temperature increase resulted in decreased cold-water viscosity because of starch degradation. It was found that cold-water viscosity was positively correlated with the crystallinity of V-type starch structure. Ethanol washing before drying made VGS dispersed better, and strengthened V-type crystalline structure, so that ethanol washed VGS had better paste properties.

Clean label starch: production, physicochemical characteristics, and industrial applications

Recently, health-conscious consumers have a tendency to avoid the use of modified starch in their food products because of reluctance regarding food additives or chemical processes. The present paper considers the characteristics and manufacturing methods of clean label starch, which is free from chemical modification. Clean label starch manufacturing is mainly dependent on starch blending, physical and enzymatic modification methods. Physical modifications include ultrasound, hydrothermal (e.g., heat-moisture treatment and annealing), pre-gelatinization (e.g., drum drying, roll drying, spray cooking, and extrusion cooking), high-pressure (high hydrostatic pressure), and pulsed electric field treatments. These physical processes allow variation of starch properties, such as morphological, thermal, rheological, and pasting properties. Enzyme treatment can change the properties of starch more dramatically. Actual use of clean label starch with such altered properties has occurred in industry and is described here. This review may provide useful information on the current status and future direction of clean label starch in the field of food science.

Effects on the structure and properties of native corn starch modified by enzymatic debranching (ED), microwave assisted esterification with citric acid (MCAE) and by the dual ED/MCAE treatment

Native corn starch was modified by enzymatic debranching (ED), microwave assisted citric acid esterification (MCAE), and by dual ED/MCAE. The structure and properties of native starch (NS), and the resulting debranched starch (DS), microwave assisted citric acid esterified starch (MCS), and microwave assisted citric acid debranched starch (MCDS) were determined and compared. Both the morphology and crystalline regions of the modified starches were changed by ED and MCAE. ED increased significantly the amylose content and transparency, but decreased the in vitro enzymatic digestibility, freeze thaw stability and relative crystallinity of DS compared to those of NS. MCAE produced a decrease in amylose content, transparency, in vitro enzymatic digestibility, and relative crystallinity, but increased the freeze-thaw stability of MCS compared to NS, and of MCDS compared to DS. The A-type crystalline structure of NS and DS was changed to B-type crystalline structure after MCAE treatment, and a new FTIR characteristic band at 1735 cm^-1 was observed for MCS and MCDS. This work provides insights for producing esterified corn starches by a combined enzyme, microwave and organic acid novel technology.

Effects of drying temperature and genotype on morphology and technological, thermal, and pasting properties of corn starch

The objective of this study was to evaluate the effects of drying temperature (30, 50, 70, and 90 °C) and genotype (yellow floury corn, white floury corn, and yellow flint corn) on the morphology and technological and thermal properties of corn starch. The white and yellow genotypes with floury endosperm (soft) had spherical starch granules, while the granules of the yellow flint genotype were polyhedral. White floury corn showed higher extraction yield, higher resistance during granules' swelling before the physical collapse, as it was not affected by the increase in drying temperature, and at 90 °C it presented higher breakdown and energy necessary for gelatinization. There were peak viscosity and gelatinization enthalpy reduction on starch from yellow floury corn and yellow flint corn according to the increase in drying temperature. Drying temperatures below 50 °C are indicated for all genotypes studied. White floury corn is indicated due to the higher extraction yield presented. Yellow floury corn is indicated for application in chilled and frozen products due to lower starch retrogradation. The yellow flint corn is indicated for application as a thickening agent due to higher gel hardness.

Autoclaving and extrusion improve the functional properties and chemical composition of black bean carbohydrate extracts

Common beans (Phaseolus vulgaris L.) are rich in starch with a high content of amylose, which is associated with the production of retrograded and pregelatinized starch through thermal treatments. The purpose of this study was to evaluate the composition, morphology, thermal, functional, and physicochemical properties of carbohydrate extracts (CE) obtained from autoclaved (100 and 121 °C) and extruded (90, 105, and 120 °C) black beans. After evaluation of the functional properties, the CE from autoclaved beans at 100 °C for 30 min and 121 °C for 15 min 2×, and extruded beans at 120 °C and 10 rpm, were selected to continue the remaining analysis. Autoclaving treatments at 100 °C for 30 min and 121 °C for 15 min 2× showed a reduction of resistant starch by 14.4% and 26.6%, respectively, compared to dehulled raw bean CE. Meanwhile, extrusion showed a reduction in resistant starch of 54.2%. Autoclaving and extrusion treatments also decreased the dietary fiber content. Extrusion reduced almost entirely the content of α-galactooligosaccharides, in comparison to dehulled raw bean CE. The results showed differences in color and granule morphology. The onset, peak, and conclusion temperatures, transition temperature range, and enthalpy of autoclaved and extruded bean CE were lower than dehulled raw bean CE. The CE from autoclaved and extruded beans contain retrograded and pregelatinized starch, which could be incorporated in food products as a thickening agent for puddings, sauces, creams, or dairy products. PRACTICAL APPLICATION: Thermally treated black bean carbohydrate extracts are rich in starch, fiber, and protein. Because these extracts are already cooked, they can be added to products that do not require a thermal process such as puddings, sauces, creams, or dairy products, acting as a thickening agent.

Evaluation of Acid-Modified Ethiopian Potato (Plectranthus edulis) Starch as Directly Compressible Tablet Excipient

Ethiopian potato is one of the tuber-bearing members of the family Lamiaceae. It is an indigenous crop in Ethiopia and important source of starch. Unprocessed native starches are structurally weak and functionally restricted for application in pharmaceutical technologies. Consequently, starch is usually modified either chemically or physically to make it convenient for industrial use. The aim of the study was to prepare and characterize acid-modified Ethiopian potato starch (AMEPS) and evaluate its functionality as a direct compressible excipient in tablet formulations. The extracted starch from Ethiopian potato tuber was modified using 6% HCl concentration for 8 days, then dried using oven and spray drying techniques, and subsequently evaluated and compared with the native Ethiopian potato starch (NEPS) and S1500® as a direct compressible excipient. Acid modification of the NEPS decreased the moisture content and swelling power while increased the percent solubility. The X-ray diffraction revealed that both the NEPS and AMEPS have B-type crystal patterns. The AMEPS showed improved flowability compared to the NEPS. This improvement was further enhanced by the spray drying process. The compactability study revealed that the tensile strength of spray-dried AMEPS (16.76 kg/cm²) was significantly higher than that of the spray-dried NEPS (7.07 kg/cm²) and S1500® (11.66 kg/cm²). The AMEPS was less sensitive to lubricants compared to the NEPS and Starch 1500®. Similarly, the dilution potential of the AMEPS was superior to the NEPS and S1500®. The AMEPS accommodated up to 50% of paracetamol while the NEPS and S1500® were able to hold only up to 30%. Pharmacopoeial specifications for disintegration and dissolution were met by the paracetamol tablets prepared by AMEPS. Thus, considering all the results obtained, spray-dried AMEPS could be a potential alternative directly compressible tablet excipient.

A new pre-gelatinized starch preparing by gelatinization and spray drying of rice starch with hydrocolloids

Rice starch with hydrocolloids (pectin, xanthan gum, sodium alginate or ι-carrageenan) was gelatinized and subsequently spray dried to prepare pre-gelatinized rice starch (PRS) with hydrocolloids (PRS-H). The PRS-H displayed concave granular shape with amorphous structure, indicating rice starch in PRS-H was completely gelatinized. Cold paste viscosity of PRS-H was enhanced in comparison with that of PRS. Especially, xanthan and ι-carrageenan increased cold paste viscosity of PRS-H more than pectin and alginate did. Cold paste viscosity of physically mixed PRS and hydrocolloids (PRS+H), and flow behavior of hydrocolloids themselves as well as gelatinized starch-hydrocolloids without spray drying (GRS-H) indicated interactions existed between starch and hydrocolloids during the preparation. Swelling power, water solubility index, and dynamic viscoelastic properties of PRS-H were also adjusted by different hydrocolloids. These results showed that premixing hydrocolloids with starch before gelatinization in method of spray drying would be a suitable methodology for manufacture PRS with altered properties.

Extruded whole buckwheat noodles: effects of processing variables on the degree of starch gelatinization, changes of nutritional components, cooking characteristics and in vitro starch digestibility

The effects of processing variables on the degree of gelatinization (DG), changes of nutritional components, cooking characteristics and in vitro starch digestibility of extruded whole buckwheat noodles were investigated.

Effect of spray-drying and extrusion on physicochemical characteristics of sweet potato starch

This study aimed to understand the physicochemical characteristics of sweet potato starch following spray-drying and extrusion processes for desirable applications. Spray-dried starch showed formation of agglomerates and decreased in average granular size from 16.5 μm of the native starch granules to 14.1 μm. Spray-drying reduced the percentage crystallinity from 25.3 to 22.6% and showed a slight decrease in the molecular weight of amylopectin from 3.1 to 2.6 × 10⁸ g mol^-1. In addition, changes in the pasting and gelatinization properties, higher final viscosity (454.4 RVU), and less enthalpy change (8.73 J g^-1) were reported after spray-drying. Thus, spray-drying resulted in partially gelatinized starch, which can be selected for making more viscous products. Extruded sweet potato starch displayed an amorphous structure, showed total loss of crystallinity, and significant reduction in molecular weight of amylopectin to 0.41 × 10⁸ g mol^-1, reflecting complete gelatinization of starch granules during extrusion. Extruded starch showed significant changes in pasting properties, including a display cold viscosity (9.4 RVU). Therefore, extruded starch was suitable for products that require quick solubility and a low final viscosity. Thus, the spray-drying and extrusion processes produce sweet potato starches with particular characteristics that can be used for different and potential applications in industries.

Design of Magnetic Polymeric Particles as a Stimulus-Responsive System for Gastric Antimicrobial Therapy

The treatment of peptic ulcers induced by H. pylori remains challenging due to the deep mucous layer location of bacteria preventing antimicrobial drug access. The present work aimed to design and evaluate in vitro dual responsive (both pH and magnetic field-sensitive) polymeric magnetic particles loaded with amoxicillin as a smart drug carrier for deep mucous layer penetration and in situ drug release. Magnetite particles were produced by the co-precipitation method and subsequently coated with the Eudragit^®S100 and amoxicillin by using the spray-drying technique. The physicochemical characterization of the obtained particles was carried out by optical and scanning electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, nitrogen adsorption/desorption isotherms, and vibrating sample magnetometry. Additionally, drug release tests and antibacterial activity tests were evaluated in vitro. Microparticles presented 17.2 ± 0.4 μm in size and their final composition was 4.3 ± 1.5% of amoxicillin, 87.0 ± 2.3% of Eudragit, and 9.0 ± 0.3% of magnetite. They were both pH and magnetic field responsive while presenting antimicrobial activity. On one side, magnetic field responsiveness of particles is expected to prompt them to reach bacterium niche in deep mucous layer by means of magnetic forces. On the other side, pH responsiveness is expected to enable drug release in the neutral pH of the deep mucous layer, preventing undesired delivery in the acidic gastric lumen. Smart microparticles were designed presenting both pH and magnetic field responsiveness as well as antimicrobial activity. These may be promising assets for peptic ulcer treatment.