Capture of iodide from wastewater by effective adsorptive membrane synthesized from MIL-125-NH2 and cross-linked chitosan

Fluorescent cellulose nanofibrils-based hydrogel incorporating MIL-125-NH2 for effective adsorption and detection of iodide ion

To remove iodine ion (I-) from wastewater, a novel hydrogel, the fluorescent cellulose nanofibrils-based hydrogel (FCNH), was synthesized to enable both detection and adsorption of I-. The FCNH comprised cellulose nanofibrils (CNs), silver nanoclusters (AgNCs), and MIL-125-NH2. It exhibited an excellent adsorption capacity for I-, with a maximum adsorption capacity of 373.7 mg/g, fitting both the Langmuir and pseudo-second-order models. Additionally, FCNH displayed excellent regeneration properties, retaining 88.0 % of its initial adsorption capacity after six adsorption-desorption cycles. Functioning as a fluorescent sensor, the synthesized FCNH enabled the detection of I- through dynamic quenching, with linear ranges of 5 to 200 mg/L and 0.2 to 1.0 μg/L, and a determination limit of 0.11 μg/L. Analysis of the adsorption and detection mechanisms revealed that FCNH's outstanding performance arose from its 3D porous structure comprising CNs, AgNCs, and MIL-125-NH2. Economic analysis indicated that FCNH was inexpensive compared to commercially available activated carbon. Thus, FCNH demonstrated significant potential as an economical and reusable adsorbent for iodine ion removal.

MIL-88A(Al)/chitosan/graphene oxide composite aerogel with hierarchical porosity for enhanced radioactive iodine adsorption

To ensure the sustainable development of the nuclear industry, the effective capture of radioiodine from nuclear wastewater has attracted much attention. Herein, a novel MIL-88A(Al)/chitosan/graphene oxide (MCG) composite aerogel was prepared by using crosslinked chitosan and graphene oxide as the 3D network skeleton, and MIL-88A(Al) nanocrystalline particles were introduced into the skeleton by freeze-drying method. MIL-88A(Al) adsorption capacities for volatile and soluble iodine were 2.02 g g-1 and 850.00 mg g-1, respectively. Owing to the synergistic effect of MIL-88A(Al), GO, CS, and the hierarchically porous structures of the MCG aerogel, the adsorption capacities for volatile and soluble iodine by the MCG aerogel were increased to 2.62 g g-1 and 1072.60 mg g-1, respectively. Furthermore, the adsorption performance of the MCG aerogel for volatile and soluble iodine could be maintained at 83 % and 82 % after 5 cycles, suggesting excellent recoverability. Meanwhile, the adsorption mechanism studies showed the interactions between iodine and NH, AlO, and CO in MCG aerogel. Furthermore, the adsorption process is consistent with the Elovich kinetic and Sips isotherm models. MCG aerogels are potential candidates for enhanced radioiodine adsorption due to their high radioiodine capture performance and excellent recyclability.

Dual modification of reverse osmosis membranes with NH2-MIL-125 and functionalised multiwalled carbon nanotubes for enhanced nanoplastic removal

The present study describes a novel double-modified strategy for developing high-performance thin-film composite reverse osmosis (TFC-RO) membranes by incorporating titanium-based metal organic frameworks (NH2-MIL-125) and functionalised multiwalled carbon nanotubes (MWCNTs) into the support layer and selective layer, respectively. Initially, the support layer was subjected to successive modifications using NH2-MIL-125 mixed with polysulfone (PSF) in dimethylformamide DMF solution to investigate their impact on the performance and properties of the support layer and resultant TFC-RO membranes. Results indicated that the new structure of the modified support layer had significant influences on the developed TFC-RO membranes. Notably, the pristine PSF support exhibited a large surface pore size, medium porosity, and strong hydrophobicity, resulting in a low-flux TFC-RO membrane. However, after modification with NH2-MIL-125, the optimal blend support demonstrated a small surface pore size, high porosity, and improved hydrophilicity, favouring the formation of a high performance TFC-RO membrane. The incorporation of functionalised MWCNTs nanochannels into the selective layer, using the optimal NH2-MIL-125-PSF blended support, resulted in a smoother and more hydrophilic TFC-RO membrane with enhanced negative charge to improve antifouling properties against negative foulants (i.e., nanoplastics (NPs) and bovine serum albumin (BSA)). The double-modified membrane (TFC-RO-DM) exhibited superior performance over the conventional PSF-TFC-RO membrane. Notably, the maximum water flux reached 39 L m-2.h-1 with 98.4% NaCl rejection. The membrane exhibited a high flux recovery rate of 92% following a 30-min physical cleaning process. Additionally, the TFC-RO-DM membrane displayed reduced fouling against NPs suggesting the great promise of this innovative double-modification approach for the advancement of high-performance TFC-RO membranes.

Urea production via photocatalytic coupling of mixed gases (CO2/NH3) using Mo(MnO4)5 supported on Ce-BTC as nano-composite catalyst

Urea used in fertilization and feed supplement, as well as a starting material for the manufacture of plastics and drugs. Urea is most commonly produced by reacting carbon dioxide with ammonia at high temperature. Photocatalysis has gained attention as a sustainable pathway for performing urea. This work focus on designing very active photocatalysts based on cerium organic framework (Ce-BTC) doped with metal oxide nanoparticles (molybdenum permanganate, Mo(MnO4)5) for production of urea from coupling of ammonia with carbon dioxide. The prepared materials were characterized using different spectral analysis and the morphology was analysed using microscopic data. The effect of catalyst loading on the production rate of urea was investigated and the obtained results showed speed rate of urea production with high production yield at low temperature. The recyclability tests confirmed the sustainability of the prepared photocatlysts (Mo(MnO4)5@Ce-BTC) which supported the beneficial of the photocatalysis process in urea production.

Stability of Iodine Species Trapped in Titanium-Based MOFs: MIL-125 and MIL-125_NH2

Two titanium-based MOFs MIL-125 and MIL-125_NH2 are synthesized and characterized using high-temperature powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA), N2 sorption, Fourier transformed infrared spectroscopy (FTIR), Raman spectroscopy, ultraviolet-visible spectroscopy (UV-Vis), and electron paramagnetic resonance (EPR). Stable up to 300 °C, both compounds exhibited similar specific surface areas (SSA) values (1207 and 1099 m2 g-1 for MIL-125 and MIL-125_NH2, respectively). EPR signals of Ti3+ are observed in both, whith MIL-125_NH2 also showing ─NH2 ●+ signatures. Both MOFs efficiently adsorbed iodine in continuous gas flow over five days, with MIL-125 trapping 1.9 g.g-1 and MIL-125_NH2 trapping 1.6 g.g-1. MIL-125_NH2 exhibited faster adsorption kinetics due to its smaller band gap (2.5 against 3.6 eV). In situ Raman spectroscopy conducted during iodine adsorption revealed signal evolution from "free" I2 to "perturbed" I2, and I3 -. TGA and in situ Raman desorption experiments showed that ─NH2 groups improved the stabilization of I3 - due to an electrostatic interaction with NH2 ●+BDC radicals. The Albery model indicated longer lifetimes for iodine desorption in I2@MIL-125_NH2, attributed to a rate-limiting step due to stronger interaction between the anionic iodine species and the ─NH2 ●+ radicals. This study underscores how MOFs with efficient charge separation and hole-stabilizer functional groups enhance iodine stability at higher temperatures.

Efficient adsorption of radioactive iodine by covalent organic framework/chitosan aerogel

Radioactive iodine is considered one of the most dangerous radioactive elements in nuclear waste. Therefore, effective capture of radioactive iodine is essential for developing and using nuclear energy to solve the energy crisis. Some materials that have been developed for removing radioactive iodine still suffer from complex synthesis, low removal capacity, and non-reusability. Herein, covalent organic framework (COF)/chitosan (CS) aerogels were prepared using vacuum freeze-drying, and the COF nanoparticles were tightly attached on the green biomass material CS networks. Due to the synergistic effect of both COF and CS, the composite aerogel shows a three-dimensional porous and stable structure in the recycle usage. The COF/CS aerogel exhibits excellent iodine adsorption capacity of 2211.58 mg g-1 and 5.62 g g-1 for static iodine solution and iodine vapor, respectively, better than some common adsorbents. Furthermore, COF/CS aerogel demonstrated good recyclability performance with 87 % of the initial adsorption capacity after 5 cycles. In addition, the interaction between iodine and imine groups, amino groups, and benzene rings of aerogel are the possible adsorption mechanisms. COF/CS aerogel has excellent adsorption properties, good chemical stability, and reusable performance, which is a potential and efficient adsorbent for industrial radioactive iodine adsorption from nuclear waste.

Efficient Removal of Iodine from Water by a Calix[4]pyrrole-Based Nanofilm

The efficient removal of radioactive iodine from an aqueous solution is largely dependent on the adsorbent materials employed. In this work, we report a calix[4]pyrrole-based nanofilm and its application for the rapid removal of iodine from water. The nanofilm was synthesized through a confined dynamic condensation of tetra hydrazide calix[4]pyrrole with 1,3,5-tri-(4-formylphenyl) aldehyde at the air/dimethyl sulfoxide (DMSO) interface. The thickness of the obtained nanofilm is ∼35 nm, enabling fast mass transfer and a high ratio of accessible binding sites for iodine. The pseudo-second-order rate constant of the nanofilm for iodine is ∼0.061 g g-1 min-1, 3 orders of magnitude higher than most reported adsorbent materials. Flow-through nanofiltration tests demonstrated that the nanofilm has an adsorption capacity of 1.48 g g-1, a high removal efficiency, and good reusability. The mechanism study revealed that the moieties of Schiff base, pyrrole, and aromatic rings play a key role for binding iodine. We believe this work provides not only a new strategy for the efficient removal of radioactive iodine from water but also new ideas for designing efficient iodine adsorbents.

Iodide ion-imprinted chitosan beads for highly selective adsorption for nuclear wastewater treatment applications

Iodide ions from radioactive iodine isotopes are common contaminants present in nuclear wastewater from nuclear power plants which are considered hazardous contaminants to be released in water sources even at low concentrations due to their association with metabolic disorders, therefore its removal from the nuclear wastewater effluents is necessary. Chitosan beads are natural and cost-efficient adsorbents that have been used for ion removal from wastewater. However, issues of poor selectivity persist in achieving high-efficiency iodide ion removal. In this study, ion-imprinted chitosan beads (IIC) have been synthesized using the phase-inversion method, IIC beads were modified by cross-linking with epichlorohydrin (IIC-EPI) and modified by cross-linking with epichlorohydrin and silicon dioxide nanoparticles (IIC-SiO2-EPI). Through 4 h of batch adsorption experiments, IIC beads achieved a maximum adsorption capacity (Qe) of 0.65 mmol g-1 and showed more preference for the iodide ions compared to the non-imprinted chitosan beads which achieved a maximum adsorption capacity of 0.27 mmol g-1 at pH 7. While the modified beads IIC-EPI and IIC-SiO2-EPI beads have boosted the adsorption capacities to 0.72 mmol g-1 and 0.91 mmol g-1. Scanning electron microscopic cross-sectional images have shown more pores and cavities than the surface images which agrees with the multilayer heterogeneous diffusion suggested by the Freundlich adsorption isotherm, that the experimental data has fitted. Adsorption kinetic data have fitted the Pseudo-second-order model as well as the Weber and Morris intraparticle model, which suggest an intraparticle pore diffusion adsorption mechanism, with the involvement of the physical electrostatic interactions with the cationic chitosan surface.

Decoration of viscose fibers with silver nanoparticle-based titanium-organic framework for use in environmental applications

To effectively remove pharmaceuticals, nitroaromatic compounds, and dyes from wastewater, an efficient multifunctional material was created based on silver nanoparticles (Ag) and MIL-125-NH2 (MOF) immobilized on viscose fibers (VF) as a support substrate. Firstly, silver nanoparticles (Ag) were immobilized on the surface of viscose fibers (VF) via in situ synthesis using trisodium citrate (TSC) as a reducing agent to create (VF-Ag). Then, VF and VF-Ag were decorated with the titanium metal-organic framework MIL-125-NH2 (MOF) to create VF-MOF and VF-Ag-MOF. The influence of VF-Ag, VF-MOF, and VF-Ag-MOF on the sonocatalytic or sonophotocatalytic degradation of sulfa drugs was investigated. The results show that VF-Ag-MOF showed excellent sonocatalytic and sonophotocatalytic activity towards the degradation of sulfa drugs compared to VF-Ag and VF-MOF. Furthermore, sonophotodegradation showed a dramatic enhancement in the efficiency of degradation of sulfa drugs compared to sonodegradation. The sonophotodegradation degradation percentage of sulfanilamide, sulfadiazine, and sulfamethazine drugs in the presence of VF-Ag-MOF was 65, 90, and 95 after 45 min of ultrasonic and visible light irradiation. The catalytic activity of VF-Ag, VF-MOF, and VF-Ag-MOF was evaluated through the conversion of p-nitrophenol (4-NP) to p-aminophenol (4-AP). The results demonstrate that VF-Ag-MOF had the highest catalytic activity, followed by VF-Ag and VF-MOF. The conversion percentage of 4-NP to 4-AP was 69%. The catalytic or photocatalytic effects of VF-Ag, VF-MOF, and VF-Ag-MOF on the elimination of methylene blue (MB) dye were investigated. The results demonstrate that VF-Ag-MOF showed high efficiency in removing the MB dye through the reduction (65%) or photodegradation (71%) after 60 min. VF-Ag-MOF composites structure-activity relationships represent that doping within silver NPs enhanced the photocatalytic activity of MIL-125-NH2, which could be explained as follows: (i) Due to the formation of a Schottky barrier at the junction between MIL-125-NH2 and Ag NPs, the photogenerated electrons in the conduction band of MIL-125-NH2 were supposed to be quickly transferred to the valence band of the Ag NPs, and subsequently, the electrons were transferred to the conduction band of Ag NPs. This considerable electron transferring process, which is reported as Z scheme heterojunction, can efficiently suppress the recombination of electron/hole pairs in VF-Ag-MIL-125-NH2 composites. (ii) Sufficient separation between the photogenerated charge carriers (holes and electrons) and avoiding their recombination enhanced the photocatalytic activity of composites.

Fabrication and optimization of febuxostat-loaded chitosan nanocarriers for better pharmacokinetics profile

The current research was planned to enhance the bioavailability of hydrophobic drug after oral administration through the development of a nanoparticle drug delivery system (DDS). Therefore, febuxostat-loaded chitosan nanoparticles (FLC NPs) were prepared using a modified ionic gelation method and optimized the reaction conditions through the design of experiments. Design expert software was used to check the desirability of the central composite design and the interactive effects of the independent variables (chitosan concentration, ratio of chitosan to linker, and pH of the medium) on the response variables (size distribution, zeta potential, polydispersity index (PDI), and entrapment efficiency (EE)) of FLC NPs. All ingredients of the optimized formulation (formulation Q) were compatible with each other as evident from FTIR, PXRD, and TGA studies, and displayed 234.7 nm particle size, 0.158 PDI, 25.8 mV zeta potential, and 76.9 % EE. TEM, SEM, and AFM exhibited a smooth, dense, and uniform structure without any visible pores in the structure of FLC NPs. The in vitro and in vivo drug release studies described a sustained release pattern of febuxostat and increased relative bioavailability by 286.63 %. Considering these findings, this chitosan nanoparticle DDS can further be used for improving the EE and bioavailability of hydrophobic drugs.

Recent advances in metal organic frameworks-based magnetic nanomaterials for waste water treatment

Magnetic nanoparticle-incorporated metal organic frameworks (MOF) are potential composites for various applications such as catalysis, water treatment, drug delivery, gas storage, chemical sensing, and heavy metal ion removal. MOFs exhibits high porosity and flexibility enabling guest species like heavy metal ions to diffuse into bulk structure. Additionally, shape and size of the pores contribute to selectivity of the guest materials. Incorporation of magnetic materials allows easy collection of adsorbent materials from solution system making the process simple and cost-effective. In view of the above advantages in the present review article, we are discussing recent advances of different magnetic material-incorporated MOF (Mg-MOF) composite for application in photocatalytic degradation of dyes and toxic chemicals, adsorption of organic compounds, adsorption of heavy metal ions, and adsorption of dyes. The review initially discusses on properties of Mg-MOF, different synthesis techniques such as mechanochemical, sonochemical (ultrasound) synthesis, slow evaporation and diffusion methods, solvo(hydro)-thermal and iono-thermal method, microwave-assisted method, microemulsion method post-synthetic modification template strategies and followed by application in waste water treatment.

Recent Advances in the Removal of Radioactive Iodine and Iodide from the Environment

Iodine (I2) in the form of iodide ions (I-) is an essential chemical element in the human body. Iodine is a nonmetal that belongs to the VIIA group (halogens) in the periodic table. Over the last couple of centuries, the exponential growth of human society triggered by industrialization coincided with the use of iodine in a wide variety of applications, including chemical and biological processes. However, through these processes, the excess amount of iodine eventually ends up contaminating soil, underground water, and freshwater sources, which results in adverse effects. It enters the food chain and interferes with biological processes with serious physiological consequences in all living organisms, including humans. Existing removal techniques utilize different materials such as metal-organic frameworks, layered double hydroxides, ion-exchange resins, silver, polymers, bismuth, carbon, soil, MXenes, and magnetic-based materials. From our literature survey, it was clear that absorption techniques are the most frequently experimented with. In this Review, we have summarized current advancements in the removal of iodine and iodide from human-made contaminated aqueous waste.

Fabrication, characterization and performance analysis of a two-step arsenic bio-filter column using Delftia spp. BAs29 and fired red mud pellets

Arsenic (As) is considered to be a grave inorganic pollutant, contaminating major aquifers worldwide. In this study, a two-step approach has been designed to combat this toxic metalloid by combining a highly efficient As (III) oxidizing bacteria; Delftia sp. BAs29 and fired red mud pellets to remove the total As from groundwater including both As (III) and As (V) ions. The maximum capacity of As (III) oxidation by Delftia sp. BAs29 was seen to be 95.65% for 500 ml of As contaminated groundwater using an optimized As (III) concentration of 300 ppb and 6.5 g of bacterial cell mass for 7 days. The second step indicated the maximum As (V) adsorption capacity by the stacked red mud pellets to be 97.91% for 500 ml of As contaminated groundwater using the optimized pore size of 106-125 μm for 7 days. The efficiency of As removal increased to 98.76% at a flow rate of 50 ml/h on combining of both the steps. In addition, the morphological properties, chemical composition, and the crystal structure of the As (V) adsorbed red mud pellets were characterized. The techno-economic feasibility of this entire unit was studied using SuperPro 10 software to estimate its optimal demand and potential. Hence, it is believed that scaling up of this two-step bio-filter column can serve as a potent filtration unit to eliminate As, both at the household and industrial level in the near future.

Electron-Donor Functional Groups, Band Gap Tailoring, and Efficient Charge Separation: Three Keys To Improve the Gaseous Iodine Uptake in MOF Materials

Metal-organic frameworks (MOFs) have been largely investigated worldwide for their use in the capture of radioactive iodine due to its potential release during nuclear accident events and reprocessing of nuclear fuel. The present work deals with the capture of gaseous I₂ under a continuous flow and its subsequent transformation into I₃^- within the porous structures of three distinct, yet structurally related, terephthalate-based MOFs: MIL-125(Ti), MIL-125(Ti)_NH₂, and CAU-1(Al)_NH₂. The synthesized materials exhibited specific surface areas (SSAs) with similar order of magnitude: 1207, 1099, and 1110 m² g^-1 for MIL-125(Ti), MIL-125(Ti)_NH₂, and CAU-1(Al)_NH₂, respectively. Because of that, it was possible to evaluate the influence of other variables over the iodine uptake capacity─such as band gap energies, functional groups, and charge transfer complexes (CTC). After 72 h of contact with the I₂ gas flow, MIL-125(Ti)_NH₂ was able to trap 11.0 mol mol^-1 of I₂, followed by MIL-125(Ti) (8.7 mol mol^-1), and by CAU-1(Al)_NH₂ (4.2 mol mol^-1). The enhanced ability to retain I₂ in the MIL-125(Ti)_NH₂ was associated with a combined effect between its amino group (which has a great affinity toward iodine), its smaller band gap (2.5 eV against 2.6 and 3.8 eV for CAU-1(Al)_NH₂ and MIL-125(Ti), respectively), and its efficient charge separation. In fact, the presence of a linker-to-metal charge transfer (LMCT) mechanism in MIL-125(Ti) compounds separates the photogenerated electrons and holes into the two distinct moieties of the MOF: the organic linker (which stabilizes the holes) and the oxy/hydroxy inorganic cluster (which stabilizes the electrons). This effect was observed using EPR spectroscopy, whereas the reduction of the Ti⁴⁺ cations into the paramagnetic Ti³⁺ species was evidenced after irradiation of the pristine Ti-based MOFs with UV light (<420 nm). In contrast, because CAU-1(Al)_NH₂ exhibits a purely linker-based transition (LBT)─with no EPR signals related to Al paramagnetic species─it tends to exhibit faster recombination of the photogenerated charge carriers as, in this case, both electrons and holes are located over the organic linker. Furthermore, the transformation of the gaseous I₂ into I_n^- [n = 5, 7, 9, ...] intermediates and then into I₃^- species was evaluated using Raman spectroscopy by following the evolution of their respective bands at about 198, 180, and 113 cm^-1. This conversion─which is favored by an effective charge separation and smaller band gaps─increases the I₂ uptake capacity of the compounds by creating specific adsorption sites for these anionic species. In fact, because the -NH₂ groups act as an antenna to stabilize the photogenerated holes, both I_n^- and I₃^- are adsorbed into the organic linker via an electrostatic interaction with these positively charged entities. Finally, changes regarding the EPR spectra before and after the iodine loading were considered to propose a mechanism for the electron transfer from the MOFs structure to the I₂ molecules considering their different characteristics.

A review on hybrid membrane-adsorption systems for intensified water and wastewater treatment: Process configurations, separation targets, and materials applied

In the era of rapid and conspicuous progress of water treatment technologies, combined adsorption and membrane filtration systems have gained great attention as a novel and efficient method for contaminant removal from aqueous phase. Further development of these techniques for water/wastewater treatment applications will be promising for the recovery of water resources as well as reducing the water tension throughout the world. This review introduces the state-of-the-art on the capabilities of the combined adsorption-membrane filtration systems for water and wastewater treatment applications. Technical information including employed materials, superiorities, operational limitations, process sustainability and upgradeing strategies for two general configurations i.e. hybrid (pre-adsorption and post-adsorption) and integrated (film adsorbents, low pressure membrane-adsorption coupling and membrane-adsorption bioreactors) systems has been surveyed and presented. Having a systematic look at the fundamentals of hybridization/integration of the two well-established and efficient separation methods as well as spotlighting the current status and prospectives of the combination strategies, this work will be valuable to all the interested researchers working on design and development of cutting-edge wastewater/water treatment techniques. This review also draws a clear roadmap for either decision making and choosing the best alternative for a specific target in water treatment or making a plan for further enhancement and scale-up of an available strategy.

NH2-MIL-125(Ti)/Reduced Graphene Oxide Enhanced Electrochemical Detection of Fenitrothion in Agricultural Products

The abuse of organophosphate pesticides causes serious threats to human health, which threatens approximately 3 million people and leads to more than 2000 deaths each year. Therefore, it is necessary to determine the residue of fenitrothion (FT) in environmental and food samples. Herein, we developed a non-enzymatic electrochemical sensor with differential pulse voltammetry signal output to determine FT in model solutions and spiked samples. Delicately, the sensor was designed based on the fabrication of hydrothermally synthesized titanium-based metal-organic frameworks (MOFs) material (NH2-MIL-125(Ti))/reduced graphene oxide (RGO) (NH2-MIL-125(Ti)/RGO) nanocomposites for better target enrichment and electron transfer. The peak response of differential pulse voltammetry for FT under optimized conditions was linear in the range of 0.072–18 μM with the logarithm of concentrations, and the detection limit was 0.0338 μM. The fabricated sensor also demonstrated high stability and reproducibility. Moreover, it exhibited excellent sensing performances for FT in spiked agricultural products. The convenient fabrication method of NH2-MIL-125(Ti)/RGO opens up a new approach for the rational design of non-enzymatic detection methods for pesticides.

Preparation of metal organic frameworks modified chitosan composite with high capacity for Hg(II) adsorption

In this study, a novel modified chitosan composite adsorbent (UNCS) was prepared by crosslinking between chitosan and metal organic frameworks (MOFs) material UiO-66-NH₂ using epichlorohydrin as crosslinker. The influence of the prepared conditions was investigated. The structure and morphology of the composite were characterized by FT-IR, XRD, SEM, TGA, BET and zeta potential analysis. Effects of different variables for adsorption of Hg(II) on this adsorbent were explored. The kinetic studies indicated that the adsorption process followed the pseudo-second-order kinetic model and the adsorption equilibrium could be reached within 2 h. The adsorption was mainly controlled by chemical process. Adsorption isothermal studies illustrated that the adsorption fitted Langmuir isotherm model, implying the homogeneous adsorption on the surface of the adsorbent. The adsorbent exhibited high uptake and the maximum capacity from Langmuir model could reach 896.8 mg g^-1 at pH 6. Thermodynamic studies showed the spontaneous nature and exothermic nature of the adsorption process. Additionally, the removal of Hg(II) on UNCS could achieve over 90 %. The adsorption-desorption cycled experiments indicated the appropriate reusability of the adsorbent. Hence, this adsorbent would be promising for the removal of Hg(II) from wastewater.

Mn3O4@polyaniline nanocomposite with multiple active sites to capture uranium(VI) and iodide: synthesis, performance, and mechanism

A major challenge for radioactive wastewater treatment and associated environmental remediation is how to simultaneously remove cationic and anionic radionuclides. Herein, a series of Mn₃O₄@polyaniline (Mn₃O₄@PANI) nanocomposites were successfully prepared and used to remove U(VI) and I^- from aqueous solution, two highly concomitant species in nuclear pollution settings. Batch adsorption experiments reveal that the component Mn₃O₄ is predominantly responsible for U(VI) removal, but PANI for I^-. The nanocomposite with 24.2 wt% Mn₃O₄ possesses high removal percentages (> 85%) either for U(VI) or I^- over a wide pH range, fast removal kinetics, and excellent adsorption selectivity at high concentrations of competing ions. Benefiting from the contributions of the two components and the high adsorption affinities, the nanocomposite achieves the simultaneous removal to coexisting U(VI) and I^-, with a maximum adsorption capacity 102.6 mg/g for U(VI) and 126.1 mg/g for I^-. X-ray photoelectron spectroscopy (XPS) results reveal that the U(VI) adsorption occurs via coordination bonding with Mn-O, -NH- , and =N- groups in the nanocomposite, whereas I^- adsorption proceeds mainly through I anionic species exchange with Cl^- and interactions with π-bonds in PANI, as well as the electrostatic attraction onto Mn₃O₄. Considering the excellent performance and multiple active sites, the Mn₃O₄@PANI nanocomposite is promising to remove practical radioactive U(VI) and I^-.

In situ growth of UiO-66-NH2 in wood-derived cellulose for iodine adsorption

The capture of radioactive iodine is an inevitable requirement in nuclear industry for environmental protection. Metal-organic frameworks (MOFs) are a new generation of sorbents that have wide applications for iodine adsorption and recovery. Although the loading of MOFs on wood can avoid the drawbacks of the powder form of MOFs in implementation, the dense structure of wood results in the lower loading, even after delignification, which limits the adsorption capacity. Herein, a hierarchically porous UiO-66-NH₂ @WCA composite was fabricated by in-situ synthesis of UiO-66-NH₂ in wood-derived cellulose aerogel (WCA) that was further removed hemicellulose from delignified wood. UiO-66-NH₂ @WCA exhibited a high loading (36 wt%) of UiO-66-NH₂ crystals and a high adsorption capacity of 704 mg/g for iodine vapor and 248 mg/g for iodine aqueous solution. The adsorption behavior in iodine aqueous solution was well predicted by the Freundlich isotherm and pseudo-second-order kinetic model. The adsorption capacity of UiO-66-NH₂ @WCA was highest in solution when the pH was 6, while the ionic strength had little effect. The hydroxyl groups on the WCA matrix had a charge transfer effect with iodine, providing additional sites for iodine capture. Furthermore, a packed column system was applied to demonstrate the excellent recyclability and potential for practical application.

A magnetic MIL-125-NH2@chitosan composite as a separable adsorbent for the removal of Cr(VI) from wastewater

Metal-organic frameworks (MOFs) are gradually used since of their huge specific surface area and superior pore structure. However, there are problems such as easy aggregation and difficult separation in water treatment. In this study, we prepared composite microspheres (FMCS-1) by modifying MIL-125-NH₂ with Fe₃O₄ and chitosan. The structural characterization and performance analysis of the materials showed that the introduction of chitosan effectively prevents the stacking of MOFs. The magnetic test manifested that Fe₃O₄ solved the problem of the difficult separation of MOFs from water. The removal potential of toxic Cr(VI) was tested by adsorption experiments. The isotherm model indicated that FMCS-1 is a single molecular layer adsorbent with a maximum adsorption capacity of 109.46 mg/g at pH = 2. The adsorption kinetics showed that the adsorption of Cr(VI) by FMCS-1 was chemical adsorption. The acid resistance test demonstrated that FMCS-1 can exist stably in acid solutions. The recycling experiments proved that the adsorbent can be reused and the removal percentage still reaches 50 % after 5 cycles. This work expands the application of MOFs in water treatment and also provides an effective adsorbent for Cr(VI) removal.

Species transformation and removal mechanism of various iodine species at the Bi2O3@MnO2 interface

Long-term exposure to excessive iodine via drinking water significantly increases the risk of thyroid diseases. Further, the mechanisms and feasible technologies for iodine removal are far from being well elucidated. In this study, we constructed a heterogeneous Bi₂O₃@MnO₂ interface with oxidation and adsorption efficiency toward iodide (I^-), and investigated the performance and mechanisms involved in iodine removal. Bi₂O₃@MnO₂ at the optimized Bi/Mn ratio of 0.05:1 had a maximum adsorption capacity of 1.19, 1.21, and 1.06 mg/g toward I^-, iodine elemental (I₂), and iodate (IO₃^-), respectively. According to the density functional theory (DFT) calculation, Bi₂O₃@MnO₂ had an adsorption energy of -2.34, -2.11, and -3.89 eV for I^-, I₂, and IO₃^-, and exhibited a better band structure and state density character for iodine removal. Based on the results of XPS, HPLC, and LC-ICP-MS characterization, Bi₂O₃ plays an important role in adsorbing and capturing I^- whereas MnO₂ dominates the moderate oxidation of I^- and the adsorption of I^- and I₂. The adsorbed I^- and I₂ concentrations on the Bi₂O₃@MnO₂ surfaces were 146.3 μg/L and 18.3 μg/L. Notably, IO₃^- was not detected owing to its moderate oxidation effect. The coexisting ions of chloride (Cl^-) and bromide (Br^-) tended to occupy the Bi₂O₃ lattice and form insoluble BiOCl and BiOBr. Further, reductive species, such as sulphite (SO₃^2-), may reduce MnO₂ to Mn(III) and Mn(II). The synergistic effect between moderate oxidation and adsorption led to Bi₂O₃@MnO₂ with high iodine removal capability. Overall, this study proposes a strategy for designing suitable interfaces and adsorbents for iodine removal; however, further studies are necessary to advance its application in practice.

Size-tunable effect of CaCO3/nanocellulose hybrid composites on the removal of paracetamol from aqueous solution

Paracetamol is a ubiquitous drug used by animals and humans but is not fully metabolized within their bodies, and thus often finds its way into raw wastewater. This study represents a new class of adsorbent nanocomposite with high adsorption capacity towards paracetamol removal. Herein, both the kinetic study and the removal of paracetamol from aqueous solutions were investigated in terms of diverse CaCO₃/nanocellulose composites with different surface charges and different particle sizes. To fine-tune these parameters, the latter was hydrothermally synthesized by manipulating of three nanocelluloses types. Precisely, micro-crystalline cellulose (MCC), nano-crystalline cellulose (CNC), and nano-fibrillated cellulose (NFC) were used as templates for precipitating CaCO₃ particles from CaCl₂ solution with the aid of Na₂CO₃. Results revealed the successful in situ deposition of calcite form of CaCO₃ with size varied relying on the base of nanocellulose. For MCC, CNC, and NFC, the size of CaCO₃ was disclosed in the range of 850-1200 nm, 350-600 nm, and 150-200 nm, respectively, regarding their surface charge. While the process of paracetamol adsorption was described by Freundlich and Langmuir isotherms, it was observed that, for MCC, the best fit of the experimental data was achieved with the Freundlich model, while the Langmuir model was the most appropriate for CNC and NFC. Also, the highest max adsorption capacities of paracetamol varied respectively to both size and surface charge of hybrid composite used. Among them, MCC/CaCO₃ composite exhibited the highest max adsorption capacity at 428 mg g^-1, clarifying that the low surface zeta potential of the latter hybrid nanocomposite is responsible for the accumulation of CaCO₃ at a bigger size with a higher affinity to adsorb paracetamol with the highest capacity due to its weak repulsion. Results also demonstrated that the material is highly effective and economical for removal of paracetamol and reusability with marginal diminishing in adsorption capacity up to 10% after five reuse cycles.

Adsorption of iodine in metal-organic framework materials

Nuclear power will continue to provide energy for the foreseeable future, but it can pose significant challenges in terms of the disposal of waste and potential release of untreated radioactive substances. Iodine is a volatile product from uranium fission and is particularly problematic due to its solubility. Different isotopes of iodine present different issues for people and the environment. 129I has an extremely long half-life of 1.57 × 107 years and poses a long-term environmental risk due to bioaccumulation. In contrast, 131I has a shorter half-life of 8.02 days and poses a significant risk to human health. There is, therefore, an urgent need to develop secure, efficient and economic stores to capture and sequester ionic and neutral iodine residues. Metal-organic framework (MOF) materials are a new generation of solid sorbents that have wide potential applicability for gas adsorption and substrate binding, and recently there is emerging research on their use for the selective adsorptive removal of iodine. Herein, we review the state-of-the-art performance of MOFs for iodine adsorption and their host-guest chemistry. Various aspects are discussed, including establishing structure-property relationships between the functionality of the MOF host and iodine binding. The techniques and methodologies used for the characterisation of iodine adsorption and of iodine-loaded MOFs are also discussed together with strategies for designing new MOFs that show improved performance for iodine adsorption.

Efficient removal of anionic, cationic textile dyes and salt mixture using a novel CS/MIL-100 (Fe) based nanofiltration membrane

The purification of hazardous textile dyeing wastewater has exhibited many challenges because it consists of a complex mixture, including dyestuff, additives, and salts. It is necessary to fabricate membranes with enhanced permeability, fouling resistance, stability, and superior dyes and salts removal from wastewater. Incorporating a highly water stable metal-organic framework (MOFs) into membranes would meet the requirements for the efficient purification of textile wastewater. In this study, nanofiltration (NF) membranes are fabricated by incorporating MIL-100 (Fe) into the chitosan (CS) through film casting technique. The effect of MIL-100 (Fe) loadings on chitosan characterized by FT-IR, XRD, contact angle measurement, FESEM-EDS, XPS, zeta potential, and surface roughness analysis. The membrane characterization confirmed the enhanced surface roughness, pore size, surface charge, and hydrophilicity. The CS/MIL-100 (Fe) membrane exhibited an improved pure water flux from 5 to 52 L/m²h as well as 99% rejection efficiency for cationic methylene blue (MB) and anionic methyl orange (MO). We obtained the rejection efficiency trend for the MB mixed salts in the order of MgSO₄ (Mg²⁺ - 51.6%, SO₄^2- - 52.5%) > Na₂SO₄ (Na⁺ - 26.3%, SO₄^2- - 29.3%) > CaCl₂ (Ca²⁺ - 21.4%, Cl^- - 23.8%) > NaCl (Na⁺ - 16.8%, Cl^- - 19.2%). In addition, the CS/MIL-100 (Fe) composite membrane showed excellent rejection efficiency and antifouling performances with high recycling stability. These stunning results evidenced that the CS/MIL-100 (Fe) nanofiltration membrane is a promising candidate for removing toxic pollutants in the textile dyeing wastewater.

Highly-efficient PVDF adsorptive membrane filtration based on chitosan@CNTs-COOH simultaneous removal of anionic and cationic dyes

An adsorptive membrane filtration based on polyvinylidene fluoride (PVDF) with chitosan (CS) and carboxylated carbon nanotubes (CNTs-COOH) is prepared by method of phase conversion, and the PVDF-CS@CNTs-COOH membranes can effectively separate anionic and cationic dye wastewater. Compared to pure PVDF membranes, PVDF-CS@CNTs-COOH increases pure water flux from 36.39 (L·m^-2·h^-1) to 85.25 (L·m^-2·h^-1), an increase of nearly 230%. The membrane exhibits excellent rejection performance in the filtration of six types of dye wastewater. The modified membranes also performed well in terms of rejection of mixed anionic and cationic dyes and also have a high performance in recycling, with a flux of over 94% for both anionic and cationic dyes. In addition, the adsorption curve fitting results showed that the adsorption process was more consistent with the pseudo-second-order adsorption kinetic model and Langmuir mode.

Hydrothermal synthesis of phosphorylated chitosan and its adsorption performance towards Acid Red 88 dye

Phosphorylated chitosan (P-CS) was successfully synthesized using a facile experimental setup of hydrothermal method that was applied to the adsorption of anionic Acid Red 88 (AR88) from aqueous media. The adsorption process obeyed the pseudo-second-order (PSO) kinetic model. In contrast, the adsorption isotherm conformed to the Langmuir model, with the maximum adsorption capacity (q_m = 230 mg g^-1) at 303 K. Both external and intraparticle diffusion strongly influenced the rate of adsorption. The insights from this study reveal that P-CS could be easily prepared and regenerated for reusability applications. The adsorption mechanism and intermolecular interaction between P-CS and AR 88 were investigated using Fourier transform infrared (FTIR) spectroscopy and calculations via Density Functional Theory (DFT). The key modes of adsorption for the P-CS/AR 88 system are driven by electrostatic attractions, H-bonding, and n-π interactions. The findings herein reveal that P-CS is a promising adsorbent for the removal of anionic dyes such as AR88 or similar pollutants from water.

Cu-Zn bimetal ZIFs derived nanowhisker zero-valent copper decorated ZnO nanocomposites induced oxygen activation for high-efficiency iodide elimination

Studies on the elimination of iodide anions (I^-) by Cu-based adsorbents have been conducted for decades, however its unsatisfactory adsorption performance and its non-reusability are still the main obstacles for large-scale practical applications. Here, an efficient technique was proposed for the elimination of iodide using nanowhisker zero-valent copper (nwZVC) decorated ZnO nanocomposites obtained by two steps pyrolysis of Cu-Zn bimetal ZIFs precursors. The as-synthesized materials were extensively characterized and the results clearly revealed that nanoscale ZVC were well-dispersed in the ZnO matrix, and the morphology and the amount of nanoscale ZVC could be tuned by adjusting the molar ratio of Cu/Zn in ZIF precursors. The following batch adsorption experiments demonstrated that the resultant materials exhibited high adsorption capacity of 270.8 mg g^-1 under condition of adequate oxygen, as well as high selectivity, strong acidity resistance and an excellent reusability. The mechanism investigations revealed that the elimination of I^- by as-fabricated materials involved adsorption process coupled with oxidation, and the existence of nwZVC was responsible for this since nwZVC could activate molecular oxygen to generate H₂O₂ accompanied by the release of Cu⁺, thus leading to I^- adsorbed by the released Cu⁺ and oxidized by the H₂O₂.

Preparation of chitosan-modified magnetic Schiff base network composite nanospheres for effective enrichment and detection of hippuric acid and 4-methyl hippuric acid

Chitosan-modified magnetic Schiff base network composite nanospheres (Fe₃O₄@SNW@Chitosan) were prepared for the enrichment and detection of hippuric acid (HA) and 4-methyl hippuric acid (4-MHA) via magnetic solid phase extraction (MSPE) connected with HPLC. The SNW was one of the covalent organic framework, which constructed through covalent bonds, shown comprising solvent stability, low density and accessible pores. The obtained Fe₃O₄@SNW@Chitosan has many merits as a magnetic sorbent, including a hydrophilic surface, uniform pore size, unique ordered channel structure, and superparamagnetism. The favourable linearity of this MSPE-HPLC method was in the range of 1-1000 μg L^-1, and LODs of HA and 4-MHA were 0.3 μg L^-1 and 0.2 μg L^-1, respectively. The recoveries in urine samples were range from 95.3 to 109.0 % with the RSD less than 9.6 %. When employed for the enrichment of HA and 4-MHA, Fe₃O₄@SNW@Chitosan exhibited great potential as a candidate for preconcentration.

Effective Pharmacophore for CDC25 Phosphatases Enzyme Inhibitors: Newly Synthesized Bromothiazolopyrimidine Derivatives

BACKGROUND

Thiazolopyrimidine analogues are versatile synthetic scaffold possessing wide spectrum of biological interests involving potential anticancer activity.

OBJECTIVE

To report the synthesis of novel bromothiazolopyrimidine derivatives and the study of both molecular modeling and in-vitro anticancer activity.

METHODS

Novel bromothiazolopyrimidine derivatives 5-18 have been prepared from 2-bromo-3-(4- chlorophenyl)-1-(3,4-dimethylphenyl)-propenone 3 as a key starting compound. The anti-cancer activities of the new compounds were evaluated against HepG2, MCF-7, A549 and HCT116 cell lines.

RESULTS

The compounds 16, 17 and 18 showed cytotoxic and growth inhibitory activities on both colon and lung cells. The cytotoxic activities of the novel synthetic compounds 8, 9, 11, 16, 17 and 18 were due to CDC25 phosphatases inhibition as shown by the enzymatic binding assay. Although compounds 8, 9 and 11 have only demonstrated CDC25B phosphatases inhibition.

CONCLUSION

The novel bromothiazolopyrimidine derivatives showed promising in vitro anticancer activities against colon cancer HCT116 and lung cancer A549 cell lines comparable to the anticancer drug doxorubicin.

Zinc-based triazole metal complexes for efficient iodine adsorption in water

Radioactive iodine is extremely harmful to the environment, and it is of great significance to develop materials that efficiently remove iodine. We prepared two triazole metal complexes with simple method, denoted as Zn(tr)(OAc) and Zn(ttr)(OAc), which were used to adsorb iodine from aqueous solution. The properties and adsorption mechanism of the two materials were studied by different techniques including XRD, SEM, N2 porosimetry at 77 K, FTIR, TGA, elemental analysis (EDS), and X-ray photoelectron spectroscopy (XPS). The results showed that both materials had good water and thermal stability. Pseudo-second-order kinetic model was better at describing the iodine adsorption kinetics onto the adsorbents. It was proved that chemical adsorption dominated, iodine mainly enriched on the materials in the form of I3-1. Zn(ttr)(OAc) had a higher adsorption capacity than Zn(tr)(OAc) due to the electron-donating group -NH2. The maximum adsorption capacity of the two materials for iodine reached 714.501 mg·g-1 and 846.108 mg·g-1 at 25 °C.

Recent Advances in Covalent Organic Frameworks for Heavy Metal Removal Applications

Covalent organic frameworks comprise a unique class of functional materials that has recently emerged as a versatile tool for energy-related, photocatalytic, environmental, and electrochromic device applications. A plethora of structures can be designed and implemented through a careful selection of ligands and functional units. On the other hand, porous materials for heavy metal absorption are constantly on the forefront of materials science due to the significant health issues that arise from the release of the latter to aquatic environments. In this critical review, we provide insights on the correlation between the structure of functional covalent organic frameworks and their heavy metal absorption. The elements we selected were Pb, Hg, Cr, Cd, and As metal ions, as well as radioactive elements, and we focused on their removal with functional networks. Finally, we outline their advantages and disadvantages compared to other competitive systems such as zeolites and metal organic frameworks (MOFs), we analyze the potential drawbacks for industrial scale applications, and we provide our outlook on the future of this emerging field.

Grafting of Acrylic Membrane Prepared from Fibers Waste for Dyes Removal: Methylene Blue and Congo Red

Dyes are a type of pollutant that have been discharged into water streams by various industries and had harmful effects on the environment and human health. Therefore, present work was directed to recycle acrylic fibers waste to be used as an adsorbent to exclude dyes such as methylene blue (MB) and Congo red (CR) from dyes-polluted wastewater. Acrylic fibers waste was converted into membrane followed by chemical grafting with p-phenylenediamine monomer to form functional modified membranes. Afterwards, some characterization analyses; Fourier transform-infrared, scanning electron microscope, swelling behavior, and porosity properties were performed for the acrylic fiber grafted membrane (AFGM). For obtaining the best conditions that permit the highest adsorption capacity of the AFGM, some preliminary experiments followed by general full factorial design experiments were displayed. Langmuir, Freundlich isotherms and kinetic studies evaluations were applied. Results revealed that, the adsorption capacities of the AFGM were 61% for Methylene blue and 86% for Congo red that stated the high affinity of the AFGM to the anionic dyes. The reusability of the AFGM membranes in different cycles for 3Rs processes “Removal, Recovery, and Re-use” indicated the efficiency of the AFGM to be used in wastewater treatment.

Construction of Core-Shell MOFs@COF Hybrids as a Platform for the Removal of UO22+ and Eu3+ Ions from Solution

The binary nanocomposites of metal/covalent-organic frameworks (NH₂-MIL-125(Ti)@TpPa-1) were constructed by solvothermal method, which was developed as a multifunctional platform with adsorption and photocatalysis for radionuclides removal. The batch experiments and physicochemical property (FT-IR, XRD, SEM, TEM, XPS, etc.) corroborated: (i) core-shell NH₂-MIL-125(Ti)@TpPa-1 had a more stable, multilayer pore structure and abundant active functional groups; (ii) NH₂-MIL-125(Ti)@TpPa-1 had fast a removal rate, as well as a high adsorption capacity of 536.73 mg (UO₂²⁺)/g and 593.97 mg (Eu³⁺)/g; (iii) the pseudo-second-order and Langmuir model provided a more reasonable description, indicating the immobilization process was endothermic, spontaneous chemisorption; (iv) the adsorption mechanism was chelation and electrostatic attraction, ascribed to the nitrogen/oxygen-containing functional groups. These results illustrated that NH₂-MIL-125(Ti)@TpPa-1 was a prospective adsorbent for the remediation polluted by radionuclides. In addition, the research provided the theoretical basis for further investigation on the UO₂²⁺(VI) photoreduction.

Removal of Methylene Blue and Congo Red Using Adsorptive Membrane Impregnated with Dried Ulva fasciata and Sargassum dentifolium

Biosorption is a bioremediation approach for the removal of harmful dyes from industrial effluents using biological materials. This study investigated Methylene blue (M. blue) and Congo red (C. red) biosorption from model aqueous solutions by two marine macro-algae, Ulva fasciata and Sargassum dentifolium, incorporated within acrylic fiber waste to form composite membranes, Acrylic fiber-U. fasciata (AF-U) and Acrylic fiber-S. dentifolium (AF-S), respectively. The adsorption process was designed to more easily achieve the 3R process, i.e., removal, recovery, and reuse. The process of optimization was implemented through one factor at a time (OFAT) experiments, followed by a factorial design experiment to achieve the highest dye removal efficiency. Furthermore, isotherm and kinetics studies were undertaken to determine the reaction nature. FT-IR and SEM analyses were performed to investigate the properties of the membrane. The AF-U membrane showed a significant dye removal efficiency, of 88.9% for 100 ppm M. blue conc. and 79.6% for 50 ppm C. red conc. after 240 min sorption time. AF-S recorded a sorption capacity of 82.1% for 100 ppm M. blue conc. after 30 min sorption time and 85% for 100 ppm C. red conc. after 240 min contact time. The membranes were successfully applied in the 3Rs process, in which it was found that the membranes could be used for five cycles of the removal process with stable efficiency.

Processing Guar Gum into polyester fabric based promising mixed matrix membrane for water treatment

A reactive and mechano-chemically stable support was prepared from Ag-nanoparticles decorated polyester fabric which was subsequently coated by a casting solution containing polyvinylidene fluoride matrix, guar gum (GG) exo-polysaccharide hydrophilic agent, and UiO-66 filler. FE-SEM, XRD, FT-IR, water contact angle technique, and mechanical stability tests were applied to characterize the prepared membranes. The water contact angle measurements indicated the hydrophilicity of the prepared membrane which can be attributed to the nature of bio-GG and UiO-66. The prepared membrane was employed for purifying contaminated waters containing N-cetyl-N,N,N-trimethylammonium bromide (CTAB) and congo-red (CR) dye through a cross-module set-up. The central composite design was also exploited to study the effect of operational parameters such as CTAB and CR concentration, pH solution, and pressure on the removal efficiency. Particularly, the bio-based GG/UiO-66 dispersion showed excellent self-healing properties, which enabled an effective pollutant separation ability and facilitated the recyclability/sustainability of the as-prepared membrane.