Facile synthesis of trimethylammonium grafted cellulose foams with high capacity for selective adsorption of anionic dyes from water

Cellulose-citric acid-chitosan@metal sulfide nanocomposites: Methyl orange dye removal and antibacterial activity

In this study, to develop efficient adsorbents in removing water pollution, new cellulose-citric acid-chitosan@metal sulfide nanocomposites (CL-CA-CS@NiS and CL-CA-CS@CuS) were synthesized by one-pot reaction at mild conditions and characterized using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscope (SEM), Energy Dispersive X-ray (EDX) and Brunauer-Emmett-Teller (BET) isotherm. The results of characterization techniques confirm that the desired compounds have been successfully synthesized. The as-prepared composites were applied for the removal of methyl orange (MO) dye from aqueous solutions using a batch technique, and the effect of key factors such as initial pH, shaking time, MO concentration, temperature and adsorbent dose were investigated and discussed. Adsorption results exhibited positive impact of temperature, shaking time and adsorbent dose on the MO removal percent. The MO removal percent has been increased over a wide range of pH from 2 (27.6 %) to 6 (98.8 %). Also, almost being constant over a wide range of MO concentration (10-70 mg/L). The results demonstrated that the maximum removal percentage of MO dye (98.9 % and 93.4 % using CL-CA-CS@NiS and CL-CA-CS@CuS, respectively) was achieved under the conditions of pH 6, shaking time of 120 min, adsorbent dose of 0.02 g, MO concentration of 70 mg/L and temperature of 35 °C. The pseudo-second-order (PSO) and Langmuir models demonstrated the best fit to the kinetic and equilibrium data. Also, the thermodynamic results showed that the MO removal process is endothermic and spontaneous in nature. The MO adsorption can be happened by different electrostatic attraction, n-π and π-π stacking and also hydrogen bonding interaction. In addition, antibacterial activity of CL-CA-CS@NiS and CL-CA-CS@CuS nanocomposites exhibited a superior efficiency against S. aureus.

Adsorption efficiency of chitosan/clinoptilolite (CS/CZ) composite for effective removal of Cd+2 and Cr+6 ions from wastewater effluents of dairy cattle farms

The wastewater effluent is responsible for the major ecological impact of the dairy sectors. To avoid the negative consequences of heavy metal pollution on the ecosystem, creative, affordable, and efficient treatment methods are now required before the effluent flows into the surrounding area. This study was aimed at assessing the effectiveness of three different adsorbents for Cd+2 and Cr+6 ions from wastewater effluents of dairy farms, including chitosan (CS), clinoptilolite zeolite (CZ), and chitosan/clinoptilolite zeolite (CS/CZ) composite. The adsorption kinetics of the CS/CZ composite were established using the effects of the key variables (pH, agitation speed, adsorbent concentrations, and contact durations). The removal (%) and adsorption capacities, qe (mg/g), were calculated using the data from the adsorption kinetics. Wastewater samples (n = 60) were collected from the wastewater effluents of five farms. Cd+2 and Cr+6 ion concentrations in all collected samples were determined. Following the CS/CZ composite creation, it was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (X-RD), and Fourier-transform infrared spectrum (FT-IR). The CS/CZ composite had an adsorption capacity of 92.4 and 96.5 mg/g for both Cd+2 and Cr+6 ions at a concentration of 2.0 g/100 ml, respectively, while the CZ adsorption capacities for the two ions were 87.5 mg/g and 61.0 mg/g, respectively, at 4.0 g/100 ml concentration. The CS was achieved at 55.56 mg/g and 33.3 mg/g, respectively, at the same concentration. The efficiency of heavy metal removal was enhanced by increasing adsorbent concentration, agitation speed, and contact duration. Using CS/CZ composite at 2.0 g/100 ml concentration, 180 min of contact time, and 300 rpm agitation speed, the greatest removal efficiencies for Cd+2 and Cr+6 ions (96.43 and 98.75%, respectively) were demonstrated.

Cationic cellulose nanofibers/chitosan auxiliary-dominated win-win strategy for paper yarn with superior color and physical performances

The colored and high-saline effluents during the traditional dyeing process poses serious environmental challenge. In our study, an eco-friendly cationic cellulose nano-fiber/chitosan (CCNF/CS) binary versatile auxiliary was designed for the neutral salt-free dyeing and physical enhancement of paper by mixing with pulp simply. Profiting from the rich cationic binding sites of CCNF/CS (Charge density: 3749.67 μmol/g), under near neutral conditions (pH = 6.2), the maximum adsorption capacity of anionic GL (Direct fast turquoise blue GL) on paper with 0.5 % CCNF/CS reached 1865.06 mg/g with a desirable evenness (45.5 % and 92.1 % higher than that of CCNF and NaCl group, respectively), and the dye uptake was up to 97 %. The spontaneous adsorption behavior was aligned with the pseudo-second-order and Langmuir models, with a primary physical mechanism enhanced by chemical forces. The combination of strong electronic attraction, hydrogen bonding, and n-π stacking effects granted CCNF/CS an enhanced proficiency in anionic dye adsorption. In addition, the tensile strength of the resulting paper yarn with 0.5 % CCNF/CS increased to 52.47 MPa under the optimal parameters, deriving from the CCNF/CS-induced inter-fiber cohesion. Overall, our research provided a green promising approach for the innovative neutral salt-free dyeing and mechanical enhancement of paper.

Bimetallic PCN-333 with Modulated Crystallization and a Porosity Structure for a Highly Efficient Removal of Congo Red

Bimetallic metal-organic frameworks (BMOFs) have garnered significant attention in the field of environmental remediation due to their more diverse adsorption sites compared to monometallic metal-organic frameworks (MOFs). Different energy barriers must be overcome for different metal ions and organic linkers to form MOFs. However, the impact of the synthesis temperature on the crystallization and porosity structure of BMOFs has been rarely studied. In this work, PCN-333 series-based BMOFs with different Fe/Al ratios were prepared by a solvothermal method at temperatures of both 135 and 150 °C. The synthesis temperature and Fe/Al ratio have significant effects on the crystal structure and specific surface area of bimetallic PCN-333, leading to the different adsorption performance of the PCN-333 for Congo red (CR). The Fe/Al-PCN-333-135(3:1) and Fe-PCN-333-150 exhibited the maximum CR adsorption capacities of 3233 and 3933 mg/g, respectively, surpassing the capacities of most previously documented adsorbents. The Langmuir model and pseudo-second-order kinetics can well describe the adsorption process of CR on Fe/Al-PCN-333-135(3:1) and Fe-PCN-333-150. Combining the isotherm adsorption behavior with the thermodynamic parameters, CR adsorption on BMOFs is a single-layer endothermic chemical adsorption. Furthermore, Fe/Al-PCN-333-135(3:1) and Fe-PCN-333-150 exhibited regenerability and reusability for three cycles with reasonable efficiency. This work is of great significance in the field of engineering BMOF materials to treat dye wastewater.

Cellulose-supported bioadsorbent from natural hemp fiber for removal of anionic dyes from aqueous solution

The aim of this study is to prepare an eco-friendly bioadsorbent by graft copolymerization and modification from hemp fiber including bio-macromolecules such as cellulose, hemicellulose and lignin for anionic dyes adsorption from aqueous solutions, and to investigate adsorptive properties. The prepared cellulose-supported bioadsorbent (TEPA-(GMA-g-HF)) was characterized in detail using SEM-EDX, STEM, FTIR, XRD, TGA and BET techniques and calculating the point of zero charge. It was used as an adsorbent to remove three different anionic dyes, Remazol Brilliant Blue R (RBBR), Reactive Red 120 (RR120) and Reactive yellow 160 (RY160) from the aqueous medium. The effects of adsorbent amount, pH, initial dye concentration, time and temperature on the adsorption were investigated. From the results, it was determined that the adsorption of all three dyes to the developed fibrous bioadsorbent was more compatible with the pseudo-second-order kinetic and the Langmuir isotherm model. It was found that the adsorption capacity increased with increasing temperature, and the adsorption capacity at 298 K was 91.70 mg/g for RBBR, 83.33 for RY160 and 76.34 mg/g for RR120, respectively. Dye removal efficiencies were provided as approximately 100 % at acidic pHs. This high removal efficiency has also achieved in the dense matrix medium, and even after five consecutive reused.

Selective Adsorption of Methyl Orange and Methylene Blue by Porous Carbon Material Prepared From Potassium Citrate

As the discharge amount of dye wastewater increases with the development of the textile printing and dyeing industries, the treatment of the dyes in the wastewater becomes more complex. The adsorption method is a commonly used method for treating dye wastewater. The adsorbent is the key factor affecting the adsorption performance. To develop a high-performance adsorbent, a porous carbon material prepared from potassium citrate by the calcination method was applied in the adsorption of dye-containing water in this study. The morphology and pore structure of the porous carbon materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and N2 adsorption/desorption isotherm. The porous carbon material with a specific surface area of 1436 m2 g-1, PC-900, was used as an adsorbent for the adsorption of methyl orange (MO) and methylene blue (MB). The results showed that the maximum adsorption capacity of PC-900 for MO and MB reached 927 and 1853.6 mg g-1, respectively. Studies on adsorption kinetics and adsorption isotherms showed that the pseudo-second-order kinetic model and the Langmuir isotherm model were more appropriate to describe the adsorption process of MO and MB by PC-900. In addition, the results of the mixed adsorption experiment of MO and MB dyes showed that PC-900 had selective adsorption for MB.

High-performance functional cellulose foam fabricated with theoretically optimized imidazolium salts for the efficient removal of ciprofloxacin

With the increasing requirements for sustainable development and environmental protection, the design and development of bio-adsorbent based on the widely sourced cellulose have attracted widespread attention. In this study, a polymeric imidazolium satls (PIMS) functionalized cellulose foam (CF@PIMS) was conveniently fabricated. It was then employed to efficiently remove ciprofloxacin (CIP). Three imidazolium salts containing phenyl groups that can lead to multiple interactions with CIP were elaborately designed and then screened through a combination of molecular simulation and removal experiments to acquire the most significant binding ability of CF@PIMS. Besides, the CF@PIMS retained the well-defined 3D network structure as well as high porosity (90.3 %) and total intrusion volume (6.05 mL g^-1) as the original cellulose foam (CF). Therefore, the adsorption capacity of CF@PIMS reached an astonishing value of 736.9 mg g^-1, nearly 10 times that of the CF. Furthermore, the pH-affected and ionic strength-affected adsorption experiments confirmed that the non-electrostatic interaction took on a critical significance in the adsorption. The reusability experiments showed that the recovery efficiency of CF@PIMS was higher than 75 % after 10 adsorption cycles. Thus, a high-potential method was proposed in terms of the design and preparation of functionalized bio-adsorbent to remove waste matters from samples of the environment.

Nano/micro-cellulose-based materials as remarkable sorbents for the remediation of agricultural resources from chemical pollutants

Overusing pesticides, fertilizers, and synthetic dyes has significantly increased their presence in various parts of the environment. The transportation of these pollutants into agricultural soil and water through rivers, soils, and groundwater has seriously threatened human and ecosystem health. Applying techniques and materials to clean up agricultural sources from pesticides, heavy metals (HMs), and synthetic dyes (SDs) is one of the major challenges in this century. The sorption technique offers a viable solution to remediate these chemical pollutants (CHPs). Cellulose-based materials have become popular in nano and micro scales because they are widely available, safe to use, biodegradable, and have a significant ability to absorb substances. Nanoscale cellulose-based materials exhibit greater capacity in absorbing pollutants compared to their microscale counterparts because they possess a larger surface area. Many available hydroxyl groups (-OH) and chemical and physical modifications enable the incorporation of CHPs on to cellulose-based materials. Following this potential, this review aims to comprehensively summarize recent advancements in the field of nano- and micro-cellulose-based materials as effective adsorbents for CHPs, given the abundance of cellulosic waste materials from agricultural residues. The recent developments pertaining to the enhancement of the sorption capacity of cellulose-based materials against pesticides, HMs, and SDs, are deliberated.

Cellulose Modified with Polyethylenimine (PEI) Using Microwave Methodology for Adsorption of Chromium from Aqueous Solutions

A large amount of agricultural waste was used to prepare cellulose (Cel) and then the surface was modified with PEI (Cel-PEI) using the microwave method. To be used as a metal adsorbent, the adsorption of Cr (VI) from an aqueous solution by Cel-PEI was measured using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) techniques. The parameters of Cr (VI) adsorption in solution by the Cel-PEI adsorbent were as follows: the pH of the solution was 3, the concentration of the chromium solution was 100 mg/L, and the adsorption time was 180 min at 30 °C using 0.01 g of adsorbent. Cel-PEI had a Cr (VI) adsorption capacity of 106.60 mg/g, while the unadjusted Cel was 23.40 mg/g and the material recovery showed a decrease in efficiency of 22.19% and 54.27% in the second and third cycles, respectively. The absorption isotherm of chromium adsorption was also observed. The Cel-PEI material conformed to the Langmuir model with an R² value of 0.9997. The kinetics of chromium adsorption showed that under pseudo-second-order analysis, with R² values of 0.9909 and 0.9958 for Cel and Cel-PEI materials, respectively. The G° and H° values of the adsorption process were negative, indicating that the adsorption is spontaneous and that the adsorption process is exothermic. The efficient preparation adsorbent materials for Cr (VI) was achieved using a short microwave method that is low-cost and environmentally friendly for use in the treatment of Cr-contaminated wastewater.

Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes

A novel reusable, high-compressible cotton regenerated cellulose/chitosan composite aerogel (RC/CSCA) was prepared using N-methylmorpholine-N-oxide (NMMO) as the green cellulose solvent, and glutaraldehyde (GA) as the crosslinking agent. The regenerated cellulose obtained from cotton pulp could chemically crosslink with chitosan and GA, to form a stable 3D porous structure. The GA played an essential role in preventing shrinkage and preserving the deformation recovery ability of RC/CSCA. Due to the ultralow density (13.92 mg/cm³), thermal stability (above 300 °C), and high porosity (97.36 %), the positively charged RC/CSCA can be used as a novel biocomposite adsorbent for effective and selective removal of toxic anionic dyes from wastewater, showing an excellent adsorption capacity, environmental adaptability, and recyclability. The maximal adsorption capacity and removal efficiency of RC/CSCA for methyl orange (MO) was 742.68 mg/g and 95.83 %.

Adsorption Studies on the Removal of Anionic and Cationic Dyes from Aqueous Solutions Using Discarded Masks and Lignin

The carbon materials derived from discarded masks and lignin are used as adsorbent to remove two types of reactive dyes present in textile wastewater: anionic and cationic. This paper introduces the results of batch experiments where Congo red (CR) and Malachite green (MG) are removed from wastewater onto the carbon material. The relationship between adsorption time, initial concentration, temperature and pH value of reactive dyes was investigated by batch experiments. It is discovered that pH 5.0-7.0 leads to the maximum effectiveness of CR and MG removal. The equilibrium adsorption capacities of CR and MG are found to be 232.02 and 352.11 mg/g, respectively. The adsorption processes of CR and MG are consistent with the Freundlich and Langmuir adsorption models, respectively. The thermodynamic processing of the adsorption data reveals the exothermic properties of the adsorption of both dyes. The results show that the dye uptake processes follow secondary kinetics. The primary adsorption mechanisms of MG and CR dyes on sulfonated discarded masks and alkaline lignin (DMAL) include pore filling, electrostatic attraction, π-π interactions and the synergistic interactions between the sulphate and the dyes. The synthesized DMAL with high adsorption efficiency is promising as an effective recyclable adsorbent for adsorbing dyes, especially MG dyes, from wastewater.

Rapid adsorption of directional cellulose nanofibers/3-glycidoxypropyltrimethoxysilane/polyethyleneimine aerogels on microplastics in water

Currently, cellulose-based aerogel materials are a hot topic owing to their high specific surface area and high porosity, as well as the green, degradable and biocompatible characteristics of cellulosic materials. Modification of cellulose to enhance the adsorption properties of cellulose-based aerogels has important research significance in solving the problem of water body pollution. In this paper, cellulose nanofibers (CNFs) were modified with polyethyleneimine (PEI), and modified aerogels with directional structures were prepared by a simple reaction and freeze-drying method. The adsorption behavior of the aerogel followed the adsorption kinetic models and isotherm models. More significantly, the aerogel could rapidly adsorb microplastics, reaching equilibrium within 20 min. Furthermore, the fluorescence displayed directly expresses the occurrence of the adsorption behavior of the aerogels. Therefore, the modified cellulose nanofiber aerogels were of reference significance for microplastic removal from water bodies.

Adsorption Properties of Anionic Dyes on Quaternized Microcrystalline Cellulose

Efficient removal of dyes in the wastewater of dyeing and printing industries is challenging, especially the anionic dyes with strong stability, serious environmental pollution, and difficult degradation. In the present work, a novel cationic adsorbent was synthesized through the quaternization of 2,3-epoxypropyltrimethylammonium chloride (GTA) onto microcrystalline cellulose and characterized by Fourier transform infrared spectroscopy, X-ray diffraction, specific surface and pore size analysis, and scanning electron microscopy. Acid Yellow 128 (AY-128) and Acid Red 1 (AR-1) were selected to investigate their adsorption on quaternized microcrystalline cellulose (QMCC). The experimental adsorption results indicated that (1) the adsorption kinetics of AY-128 and AR-1 on QMCC could be consistent with the pseudo-second-order and Freundlich models, respectively; (2) the adsorption process was spontaneous and feasibly endothermic. The removal efficiency of AY-128 and AR-1 was up to 99 and 95%, respectively. After five times of reuse, the removal efficiency of AY-128 and AR-1 was still 97 and 95%. In conclusion, quaternized microcrystalline cellulose was a promising adsorbent for AY-128 and AR-1.

Construction of a polyoxometalate-based magnetic composite MOF for the effective adsorption of cationic dyes

Adsorption and separation of dyes are extremely important as they damage the water environment and human health. ZIF-8 has the benefits of large specific surface area, explicit structure and a good confinement effect on POM, which can better facilitate the synergetic effect of POM and ZIF-8. Therefore, ZIF-8 was chosen as the support material to wrap H₃PW₁₂O₄₀. In the present work, magnetic ZIF-8@H₃PW₁₂O₄₀ composites were prepared by a facile impregnation synthesis strategy and applied to the adsorption of cationic dyes with methylene blue (MB) as a representative. Compared with the other three prepared materials, Fe₃O₄@ZIF-8@H₃PW₁₂O₄₀ exhibited the best adsorption performance. The adsorption process conformed to the pseudo-second-order model and the Langmuir model, and the adsorption reaction was spontaneous with the maximum adsorption capacity of up to 431.03 mg g^-1 within 20 min. The electrostatic attraction has been testified to be the major driving force of the adsorption process, and the material can still hold 90% of the max adsorption capacity after 5 cycles, which serve as the foundation for its further applications in the field of adsorption.

Copper-carbon hybrid nanoparticles as antimicrobial additives

Millions of cases of hospital-acquired infections occur every year involving difficult to treat bacterial and fungal agents. In an effort to improve patient outcomes and provide better infection control, antimicrobial coatings are ideal to apply in clinical settings in addition to aseptic practices. Most efforts involving effective antimicrobial surface technologies are limited by toxicity of exposure due to the diffusion. Therefore, surface-immobilized antimicrobial agents are an ideal solution to infection control. Presented herein is a method of producing carbon-coated copper/copper oxide nanoparticles. Our findings demonstrate the potential for these particles to serve as antimicrobial additives.

Graphical abstract

Supplementary Information

The online version contains supplementary material available at 10.1557/s43579-022-00294-2.

Fe-C-based materials: synthesis modulation for the remediation of environmental pollutants-a review

Presently, the rapid pace in the discovery of emerging aquatic pollutants is increasing the demand for the remediation and treatment of our natural resources. Regarding this, nanotechnology is being considered the potential solution for contaminated water remediation with techniques such as filtration, adsorption, catalysis, and desalination. For this purpose, zerovalent iron (ZVI) is being widely used in the remediation of environmental pollutants due to its large specific surface area and high reactivity. However, ZVI is easy to agglomerate and oxidize, limiting its application in the real environment. Therefore, the present study was designed to discuss the preparation and characterization methods of ZVI composite materials, factors affecting adsorption, the removal effect, and adsorption mechanism of different pollutants by Fe-C materials because the optimization and modification of nano-zero-valent iron is a hot research topic nowadays in this field. Moreover, this paper does also analyze the possibility of the practical application prospects of the team's technology for preparing iron-carbon materials. Thus, this information will be helpful for the development and application of Fe-C-based technologies for water and soil remediation and the prediction of the future research direction of Fe-C composite materials.

Ionic liquid treated leaves of Juglans regia as an adsorbent for the removal of methyl orange dye: experimental, computational, and statistical approach

The novel biosorbents prepared by surface modification from leaves of Juglans regia plant were exploited for removal of methyl orange dye from aqueous solution. The leaves in the form of dust and charcoal were separately impregnated with 1-butyl-3-methyl imidazolium bromide (I) to obtain adsorbents namely J. regia dust/charcoal impregnated with I (JRDI/JRCI) which were characterized using advanced analytical approaches. The impregnation of ionic liquid was confirmed by the appearance of new bands. Langmuir isotherm fitted well; the calculated adsorption capacity being 59.37 (JRDI) and 102.72 mg g^-1 (JRCI). The kinetic study revealed that sorption obeyed the pseudo-first order model; the experimental adsorption capacity being 53.53 (JRDI) and 86.82 mg g^-1 (JRCI) at selected conditions of pH 3, initial dye concentration 100 ppm, dosage of adsorbent 0.3 g and contact time 70 min. The mathematical models which predicted adsorption capacity as 51.5 (JRDI) and 82.1 mg g^-1 (JRCI) were found at par with experimental values. Fukui condensed functions revealed that adsorbents had electron deficient electrophilic reaction sites while dye had electron-rich nucleophilic reaction sites. The structural properties and good adsorption capability of adsorbents indicate that they could be used as potential, eco-friendly adsorbents for the treatment of negatively charged dye pollutants.

A facile approach to cellulose/multi-walled carbon nanotube gels-Structure, formation process and adsorption to methylene blue

In view of the deficiencies in the preparation of cellulose gels, such as, cumbersome process, harsh conditions, high consumption of chemicals, secondary pollution caused by side reactions, this work reports a facile approach to make cellulose/multi-walled carbon nanotube (MWCNTs) hydrogels and aerogels via mixing cellulose with N,N'-methylene bisacrylamide (MBA) and MWCNTs in NaOH/urea/H₂O aqueous solution. The gels were revealed to be formed by an addition reaction between the double bonds of MBA and the hydroxyl groups of cellulose and the intermolecular interactions between cellulose and MWCNTs. The preparation process can be realized at room temperature and atmospheric pressure without the intervention of ultrasonic dispersion, catalyst and initiator. The gelation time, puncture strength and water retention ability of the hydrogels were investigated. Results showed that, compared with pure cellulose hydrogel, cellulose/MWNCTs hydrogels have obviously shorter sol-gel transition time (124-129.2 min), higher puncture strength (29.6022-34.2854 KPa) and water retention ability (274.2619-301.7291 g/g). Cellulose/MWCNTs aerogels possessed three dimensional network with macroporous structure (about 500 μm), low density (0.00546-0.00557 g/cm³), high porosity (99.6360-99.6426 %), good thermal stability (242 °C) and certain absorbency to methylene blue (233.2901-242.1122 mg/g).

Synthesis, characterization and application of new adsorbent composites based on sol-gel/chitosan for the removal of soluble substance in water

In this work, new adsorbent composites from the silica precursor tetraethyl orthosilicate (TEOS) and chitosan have been successfully synthesized, denominated 20%Chi, 30%Chi and 40%Chi. The composites presented enhanced chemical and physical characteristics, with emphasis on the high surface areas between 374.94 m²/g to 886.31 m²/g. The application of the composites in the model system (TY - Tartrazine yellow dye), presented adsorption capacities dependent on the amount of chitosan in the composite (40%Chi > 30%Chi > 20%Chi). However, from the experimental data of the constituent materials, 30%Chi provided the greatest increase in the adsorption capacity in the monolayer, with values of 36%. This demonstrates that the amount of chitosan in the compound alters the arrangement of adsorption sites. The 30%Chi composite presented life cycle superior to 10 reuse cycles.

•

The addition of silica provided better physical and chemical properties to the developed composites.

•

The synthesis of the 30%Chi composite enabled an increase in the adsorption capacity of the TY dye.

•

The 30%Chi composite obtained a surface area of 886.31 m²/g.

•

The 30%Chi composite was useful for more than 10 adsorption and desorption cycles.

Adsorption of dyes methyl violet and malachite green from aqueous solution on multi-step modified rice husk powder in single and binary systems: Characterization, adsorption behavior and physical interpretations

A novel modified rice husk (MRH) has been prepared for removing cationic dyes in both single system and binary system. SEM-EDS, FT-IR, XRD and XPS were used to characterize the physical and chemical properties of MRH. It showed that the maximum adsorption capacity of MRH for methyl violet (MV) and malachite green (MG) in single system was 154.49 and 996.97 mg g^-1, while in binary system was 530.94 and 408.58 mg g^-1, respectively. The experimental results showed that the pseudo-second-order kinetic model was better to describe the kinetic behavior of MV and MG adsorption. By using double layer adsorption model, we found that the n_D for MV adsorption were 2.52, 2.65 and 3.34 at 298, 308 and 318 K, respectively, and the n_D for MG adsorption were 4.59, 4.85 and 4.30, respectively. These results illustrated that multiple dye molecules were adsorbed on one adsorption site in non-parallel direction, indicating that the adsorption of dyes is multi-molecular mechanism. Furthermore, synergistic and antagonistic adsorption might be existed simultaneously in binary system. In summary, MRH has been shown well adsorption properties and reusability and our finding might provide a new idea for developing low-cost, efficient and reusable adsorbent to remove dyes from wastewater.

Multifunctional Cellulose and Cellulose-Based (Nano) Composite Adsorbents

In recent years, faced with the improvement of environmental quality problems, cellulose and cellulose-based (nano) composites have attracted great attention as adsorbents. In this review article, we first report the recent progress of modification and functionalization of cellulose adsorbents. In addition, the adsorbents produced by the modification and functionalization of carboxymehyl cellulose are also introduced. Moreover, the cellulose-based (nano) composites as adsorbents are reviewed in detail. Finally, the development prospect of cellulose and cellulose-based (nano) composites is studied in the field of the environment. In this review article, a critical comment is given based on our knowledge. It is believed that these biomass adsorbents will play an increasingly important role in the field of the environment.

Hyperbranched polymers as superior adsorbent for the treatment of dyes in water

The effective control on environmental pollutants is crucial for the proper management of diverse environmental systems (e.g., soil, water, and air). In this respect, the utility of various functional materials such as hyperbranched polymers (HPs) has been recognized due to their great potentil as adsorbent for the mitigation of numerous environmental pollutants. Here, we highlight the latest progress achieved in the design and construction of HPs with high adsorption potentials. We focus on adsorption mechanisms, functionalization methods, the role of functional groups in adsorption capacity, and the choice of HPs in adsorption of cationic and anionic dyes. Recent published reports are reviewed to quantify and qualify the removal efficiency of pollutants through adsorption. We also evaluate the adsorbing efficiency of the constructed HPs and compared their performance with other such systems. The utilization potential of new materials (magnetic, polar, and biological) is highlighted along with the methods needed for their preparation and/or modification (surface, end-group, and zwitterionic) for the construction of efficient adsorbing systems. Finally, the advantages and limitations of adsorbing systems are described along with the existing challenges to help establish guidelines for future research. This article is thus expected to offer new path and guidance for developing advanced HP-based adsorbents.

Electrospun molecularly imprinted sodium alginate/polyethylene oxide nanofibrous membranes for selective adsorption of methylene blue

Molecular imprinting technique is an efficient method to improve the selective adsorption capacity for the target pollutant. In this study, sodium alginate/polyethylene oxide molecularly imprinted nanofibrous membrane (SA/PEO-MINM) with average diameter of 185 ± 20 nm was successfully synthesized by electrospinning for selective adsorption of methylene blue (MB). Benefiting from the molecular imprinted technology, the adsorption amount of SA/PEO-MINM for MB was increased by about 65%, significantly higher than the non-imprinted membrane. Results showed that the adsorption equilibrium could be well fitted with Langmuir isotherm model and the maximum adsorption capacity towards MB was 3186.7 mg/g. Kinetic experiments well complied with the Pseudo second order model. Reusability studies indicated that the removal efficiency of MB could maintain 93% of the original adsorption capacity after four consecutive adsorption/desorption cycles. More importantly, the SA/PEO-MINM with high surface area and specific adsorption recognition sites showed excellent selective adsorption capacity in the adsorption experiment of MB and methylene orange mixed dye solution. In general, the SA/PEO-MINM can be successfully applied for the selective removal of MB from dye wastewater.

Electromagnetic Shielding and Flame Retardancy of Composite Films Constructed with Cellulose and Graphene Nanoplates

Aimed at improving the electromagnetic (EM) shielding and flame retardancy of cellulose materials, graphene (GE) nanoplates were introduced into cellulose matrix films by blending in1-allyl-3-methylimidazolium chloride. The structure and performance of the obtained composite films were investigated using scanning electron microscopy, X-ray diffraction, thermogravimetric (TG) analysis, EM shielding effectiveness (SE), and combustion tests. GE introduction formed and stacked laminated structures in the films after drying due to controlled shrinkage of the cellulose matrix. The lamination of GE nanoplates into the films was beneficial for providing EM shielding due to multiple internal reflection of EM radiation; furthermore, they also increased flame resistance based on the “labyrinth effect.” The SE of these composite films increased gradually with increased GE content and reached 22.3 dB under an incident frequency of 1500 MHz. TG analysis indicated that these composite films possessed improved thermal stability due to GE addition. Reduced flammability was confirmed by their extended times to ignition or inability to be ignited, reduced heat release rates observed in cone calorimetry tests, and increased limiting oxygen index values. These films with improved EM shielding and flame retardancy could be considered potential candidates for multipurpose materials in various applications, such as electronics and radar evasion.

Fabrication of Stable MIL-53(Al) for Excellent Removal of Rhodamine B

Adsorptive purification of organic dyes in wastewater is significant to protect the water environment. Herein, MIL-53(Al) was successfully fabricated through a facile and versatile solvothermal strategy. The stability of MIL-53(Al) under high temperature, acid, base, and peroxide conditions was investigated. The porous MIL-53(Al) had high chemical stability, and the thermal stability reached up to 500 °C, which provided a good foundation for dye removal. MIL-53(Al) showed excellent adsorption performance. The maximum adsorption capacity of MIL-53(Al) for rhodamine B (RhB) can reach 1547 mg g^-1 under 303 K, and the corresponding removal efficiency exceeded 90% at the equilibrium time (120 min). The Langmuir model and pseudo-second-order model can well fit RhB adsorption on MIL-53(Al). Thermodynamic study and activation energy values over the range of 298-323 K revealed that the adsorption of RhB was a spontaneous and endothermic physical process in nature. The batch experimental results, X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared (FTIR) spectroscopy analyses suggested that the hydrogen bonding and electrostatic interactions between the hydroxyl/carboxyl groups of MIL-53(Al) and RhB were the primary adsorption mechanisms. Besides, MIL-53(Al) had a higher selectivity to RhB than the coexisting ions in aqueous solution and a superior adsorption performance after five cycles.

Facile synthesis of amine-crosslinked starch as an efficient biosorbent for adsorptive removal of anionic organic pollutants from water

Developing applicable biosorbents for adsorptive removal of organic pollutants from water is highly demanded. However, most biosorbents suffer poor adsorption capability for anionic organic pollutants due to their negatively charged surface. Herein, we present a facile method to synthesize amine-crosslinked starch (ACS) biosorbent for removing anionic organic pollutants. The adsorption properties of ACS were thoroughly evaluated by selecting anionic brilliant blue (BB), amaranth (ART), diclofenac sodium (DS) as representatives. The results show that the ACS can selectively adsorb anionic molecules with large adsorption capacity and fast removal rate. The adsorption kinetic and isotherm behaviors can be well described by the pseudo-second-order and Langmuir models, respectively. The maximum uptake capacity of ACS for BB, ART and DS is as high as 1287.7, 724.6 and 595.2 mg g^-1, respectively. Moreover, the ACS can be easily regenerated and still exhibits favorable adsorption performance even after reusing for five times.

Synthesis, characterization, and selective dye adsorption by pH- and ion-sensitive polyelectrolyte galactomannan-based hydrogels

Three novel polyelectrolyte galactomannan hydrogels (PGHs) were fabricated by chemically crosslinking quaternary ammonium galactomannan (QAG) and carboxymethyl galactomannan (CMG), and employed for the removal of Congo Red (CR) and Methylene Blue (MB). Physicochemical characterization revealed that the PGHs are chemically and physically crosslinked. The PGHs are pH- and ion-sensitive, and their physical crosslinking can be destroyed by artificial urine; water swelling capacity (100.6-321.9 g/g dry gel) and artificial urine swelling capacity (35.9-80.5 g/g dry gel). The adsorption of CR and MB was studied and found to be pH-dependent and selective. The maximum adsorption capacities of CR and MB on the QAG and CMG gels are 1441 and 94.52 mg/g, respectively, and their adsorption kinetics and isotherm behavior obey the pseudo-second-order kinetics model and Langmuir isotherm model, respectively. The adsorption mechanism is dominated by electrostatic interactions and hydrogen bonding. Further, the PGHs have excellent salt resistance and are reusable.

Preparation and Kinetic Studies of Cross-Linked Chitosan Beads Using Dual Crosslinkers of Tripolyphosphate and Epichlorohydrin for Adsorption of Methyl Orange

Preparation of cross-linked chitosan beads using dual crosslinkers of tripolyphosphate (TPP) and epichlorohydrin (ECH) for the adsorption and kinetic studies of methyl orange (MO) had been carried out. FTIR spectra showed that TPP could act as the protecting agent of the NH₂ group of chitosan and ECH reacted with the primary hydroxyl group of chitosan. Various concentrations of TPP, ECH, and immersing time in the TPP solution for bead formation were studied. The effect of pH and kinetics of adsorption were investigated to define the mechanism of adsorption and rate-limiting step. As a result, pH 3, 10% (w/v) TPP, 5% (v/v) ECH, and 12 h immersing time in TPP were selected as the optimum conditions for preparing the beads as indicated by the highest adsorption amount of MO. The cross-linked chitosan beads' adsorption capacity for MO under optimum condition was found to be 79.55 mg/g with the adsorption rate constant (k) of 1.29 × 10⁻³/min. Furthermore, it was found that a low concentration of ECH could maintain the stability of chitosan in acidic conditions, whereas the concentration of TPP and immersing time controlled pore size and morphology of chitosan beads. The mechanism of adsorption of MO was controlled by the pore and rigidity of cross-linked chitosan beads. Bulk diffusion acted as a rate-limiting step, and a high concentration of MO inhibited diffusion and adsorption itself.

Facile synthesis of chitosan-based acid-resistant composite films for efficient selective adsorption properties towards anionic dyes

To effectively and selectively remove toxic anionic dyes which are heavily discharged and to promote them recovery, a sustainable cellulose nanofiber/chitosan (CNF/CS) composite film was elaborately designed through a facile procedure. Based on the strong supporting effect of CNF and excellent compatibility between CNF and CS, the composite film presents low swelling and acid-proof properties, which can prevent the adsorption process from the disintegration of adsorbent. Moreover, the positive electrical property of CNF/CS film increases the discrepancy in adsorption capacities for anionic and cationic dyes. The maximum adsorption capacity of anionic methyl orange (MO) on CNF/CS film reaches 655.23 mg/g with a desirable recyclability. The adsorption behavior attributed to a physico-chemical and monolayer adsorption process. This work opens a new route for the development of eco-friendly and highly efficient adsorbents on selective removal and recycling of anionic dyes from wastewater.

Novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) adsorbent for the ultrafast and efficient removal of anionic dyes

The removal of anionic dyes from wastewater has attracted global concern. In this work, a novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) (Fe3O4-pDMC) adsorbent for the efficient removal of anionic dyes from wastewater was successfully synthesized by grafting methacryloxyethyltrimethyl ammonium chloride (DMC) on the surfaces of Fe3O4. Various characterization analyses confirmed that the obtained Fe3O4-pDMC possessed numerous functional groups on its surfaces and retained good magnetic separation properties. Fe3O4-pDMC showed ultrafast removal for acid orange 7 (AO7, 58.6%, 1 min) and direct blue 15 (DB15, 98.1%, 1 min), and the maximum adsorption capacity was high (266.8 and 336.5 mg g-1 for AO7 and DB15, respectively). In addition, the adsorption process was in accordance with pseudo-second-order kinetics and the Langmuir isotherm. The mechanism underlying the adsorption of Fe3O4-pDMC on anionic dyes was mainly dependent on electrostatic interaction. This study illustrated that Fe3O4-pDMC has great potential applications as an environmentally friendly, desirable adsorbent for the efficient removal of anionic dyes from wastewater.