Physicochemical characteristic of regenerated cellulose/N-doped TiO2 nanocomposite membrane fabricated from recycled newspaper with photocatalytic activity under UV and visible light irradiation

Sustainability in Membrane Technology: Membrane Recycling and Fabrication Using Recycled Waste

Membrane technology has shown a promising role in combating water scarcity, a globally faced challenge. However, the disposal of end-of-life membrane modules is problematic as the current practices include incineration and landfills as their final fate. In addition, the increase in population and lifestyle advancement have significantly enhanced waste generation, thus overwhelming landfills and exacerbating environmental repercussions and resource scarcity. These practices are neither economically nor environmentally sustainable. Recycling membranes and utilizing recycled material for their manufacturing is seen as a potential approach to address the aforementioned challenges. Depending on physiochemical conditions, the end-of-life membrane could be reutilized for similar, upgraded, and downgraded operations, thus extending the membrane lifespan while mitigating the environmental impact that occurred due to their disposal and new membrane preparation for similar purposes. Likewise, using recycled waste such as polystyrene, polyethylene terephthalate, polyvinyl chloride, tire rubber, keratin, and cellulose and their derivates for fabricating the membranes can significantly enhance environmental sustainability. This study advocates for and supports the integration of sustainability concepts into membrane technology by presenting the research carried out in this area and rigorously assessing the achieved progress. The membranes' recycling and their fabrication utilizing recycled waste materials are of special interest in this work. Furthermore, this study offers guidance for future research endeavors aimed at promoting environmental sustainability.

Cation-Selective Actuator-Sensor Response of Microcrystalline Cellulose Multi-Walled Carbon Nanotubes of Different Electrolytes Using Propylene Carbonate Solvent

Microcrystalline cellulose (MC) with 50 wt.% multi-walled carbon nanotube (MCNT) composites is obtained through extrusion, forming MC-MCNT fiber. In this study, we concentrate on three different electrolytes in propylene carbonate (PC) which have the same anions (TF-, trifluoro-methanesulfonate CF3SO3-) but different cations, EDMI+ (1-ethyl-2,3-dimethylimidazolium), Li+ (lithium ion), and TBA+ (tetrabutylammonium). Cyclic voltammetry and square wave potential steps, in combination with linear actuation measurements in a potential range of 0.7 V to -0.2 V, were conducted. Our goal in this work was to establish a cation-selective actuator-sensor device capable of distinguishing different cations. The linear actuation of MC-MCNT fiber had its main expansion at discharge due to the incorporation of TF- in the MC-MCNT fiber with the cations. In the following order, TBA+ > EDMI+ > Li+ had the best stress, strain, charge density, diffusion coefficients, and long-term stability. Chronopotentiometric measurements revealed that the cations in the PC solvent can be differentiated by their ion sizes. Further characterization of the MC-MCNT fiber was completed using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and FTIR and Raman spectroscopy.

A bibliometric analysis of green technologies applied to water and wastewater treatment

Freshwater scarcity, a problem that has arisen particularly as a result of the progressive environmental damage caused by human consumption patterns, is strongly associated with a loss of living quality and a drop in global socioeconomic development. Wastewater treatment is one of the measures being taken to mitigate the current situation. However, the majority of existing treatments employ chemicals that have harmful environmental consequences and low effectiveness and are prohibitively expensive in most countries. Therefore, to increase water supplies, more advanced and cost-effective water treatment technologies are required to be developed for desalination and water reuse purposes. Green technologies have been highlighted as a long-term strategy for conserving natural resources, reducing negative environmental repercussions, and boosting social and economic growth. Thus, a bibliometric technique was applied in this study to identifying prominent green technologies utilised in water and wastewater treatment by analysing scientific publications considering authors, keywords, and countries. To do this, the VOSviewer software and Bibliometrix R Package software were employed. The results of this study revealed that constructed wetlands and photocatalysis are two technologies that have been considered as green technologies applicable to the improvement of water and wastewater treatment processes in most scientific articles.

Recent advances in the hybridization of cellulose and semiconductors: Design, fabrication and emerging multidimensional applications: A review

Cellulose is a plentiful, biodegradable, renewable, and natural polymer in the world that can be widely utilized in the production of polymer nanocomposites. Cellulose is developed in nanomaterials owing to its remarkable inherent features of low density, non-toxicity, and affordability, as well as the amazing sample characteristics of strength and thermal stability. Recently, there has been a lot of interest in organic-inorganic composites because of their adaptable qualities. Cellulose and semiconductors have exciting properties, and new combinations of both materials may result in efficient functional hybrid composites with distinct properties. Lately, a huge study was reported on cellulose and semiconductor-based nanocomposites. In this review, we summarize the present research development in the preparation methods, structure, features, and possible applications of multifunctional cellulose and semiconductor-based nanocomposites. The cellulose/semiconductor based nanocomposites have massive potential applications in the areas of photodegradation of organic dyes, hydrogen production, metal removal, biomedical, and sensor applications. It is also assumed that this article will promote additional investigation and will establish innovative capabilities to enhance novel cellulose and semiconductor based nanocomposites with new and exciting applications.

Recent advances in cellulose supported photocatalysis for pollutant mitigation: A review

In recent times, green chemistry or "green world" is a new and effective approach for sustainable environmental remediation. Among all biomaterials, cellulose is a vital material in research and green chemistry. Cellulose is the most commonly used natural biopolymer because of its distinctive and exceptional properties such as reproducibility, cost-effectiveness, biocompatibility, biodegradability, and universality. Generally, coupling cellulose with other nanocomposite materials enhances the properties like porosity and specific surface area. The polymer is environment-friendly, bioresorbable, and sustainable which not only justifies the requirements of a good photocatalyst but boosts the adsorption ability and degradation efficiency of the nanocomposite. Hence, knowing the role of cellulose to enhance photocatalytic activity, the present review is focused on the properties of cellulose and its application in antibiotics, textile dyes, phenol and Cr(VI) reduction, and degradation. The work also highlighted the degradation mechanism of cellulose-based photocatalysts, confirming cellulose's role as a support material to act as a sink and electron mediator, suppressing the charge carrier's recombination rate and enhancing the charge migration ability. The review also covers the latest progressions, leanings, and challenges of cellulose biomaterials-based nanocomposites in the photocatalysis field.

Near-Infrared (NIR) Silver Sulfide (Ag2S) Semiconductor Photocatalyst Film for Degradation of Methylene Blue Solution

A silver sulfide (Ag₂S) semiconductor photocatalyst film has been successfully synthesized using a solution casting method. To produce the photocatalyst films, two types of Ag₂S powder were used: a commercialized and synthesized powder. For the commercialized powder (CF/comAg₂S), the Ag₂S underwent a rarefaction process to reduce its crystallite size from 52 nm to 10 nm, followed by incorporation into microcrystalline cellulose using a solution casting method under the presence of an alkaline/urea solution. A similar process was applied to the synthesized Ag₂S powder (CF/syntAg₂S), resulting from the co-precipitation process of silver nitrate (AgNO₃) and thiourea. The prepared photocatalyst films and their photocatalytic efficiency were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and UV-visible spectroscopy (UV-Vis). The results showed that the incorporation of the Ag₂S powder into the cellulose films could reduce the peak intensity of the oxygen-containing functional group, which indicated the formation of a composite film. The study of the crystal structure confirmed that all of the as-prepared samples featured a monoclinic acanthite Ag₂S structure with space group P₂₁/C. It was found that the degradation rate of the methylene blue dye reached 100% within 2 h under sunlight exposure when using CF/comAg₂S and 98.6% for the CF/syntAg₂S photocatalyst film, and only 48.1% for the bare Ag₂S powder. For the non-exposure sunlight samples, the degradation rate of only 33-35% indicated the importance of the semiconductor near-infrared (NIR) Ag₂S photocatalyst used.

Natural Cotton Cellulose-Supported TiO2 Quantum Dots for the Highly Efficient Photocatalytic Degradation of Dyes

The artificial photocatalytic degradation of organic pollutants has emerged as a promising approach to purifying the water environment. The core issue of this ongoing research is to construct efficient but easily recyclable photocatalysts without quadratic harm. Here, we report an eco-friendly photocatalyst with in situ generated TiO₂ quantum dots (TQDs) on natural cotton cellulose (CC) by a simple one-step hydrothermal method. The porous fine structure and abundant hydroxyl groups control the shape growth and improve the stability of nanoparticles, making natural CC suitable for TQDs. The TQDs/CC photocatalyst was synthesized without the chemical modification of the TQDs. FE-SEM and TEM results showed that 5-6 nm TQDs are uniformly decorated on the CC surface. The long-term stability in photocatalytic activity and structure of more than ten cycles directly demonstrates the stability of CC on TQDs. With larger CC sizes, TQDs are easier to recycle. The TQDs/CC photocatalysts show impressive potential in the photocatalytic degradation of anionic methyl orange (MO) dyes and cationic rhodamine B (RhB) dyes.

A Facile One-Pot Approach to the Fabrication of Nanocellulose-Titanium Dioxide Nanocomposites with Promising Photocatalytic and Antimicrobial Activity

The combination of cellulosic materials and metal oxide semiconductors can provide composites with superior functional properties compared to cellulose. By using nanocellulose derived from agricultural waste, we propose a one-pot and environmentally friendly approach to the synthesis of nanocellulose-TiO₂ (NC-TiO₂) nanocomposites with peculiar photocatalytic activity and antibacterial effects. The as-prepared NC-TiO₂ composites were fully characterized by different techniques, such as X-ray diffraction (XRD), μ-Raman, Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and diffuse reflectance spectroscopy (DRS). The results showed that well crystalline anatase TiO₂ nanoparticles of about 5-6 nm were obtained. The photocatalytic activity in particular was evaluated by using methyl orange (MO) solution as a target pollutant at different pH values. It was found that all the tested NC-TiO₂ nanocomposites showed stable photocatalytic activity, even after consecutive photocatalytic runs. In addition, NCT nanocomposites with higher TiO₂ content showed degradation efficiency of almost 99% towards MO after 180 min of UV illumination. Finally, NC-TiO₂ nanocomposites also showed intriguing antimicrobial properties, demonstrating to be effective against Gram-positive (Staphylococcus aureus, Bacillus subtilis) with 20-25 mm of inhibition zone and Gram-negative bacteria (Escherichia coli, Pseudomonas aeuroginosa) with 21-24 mm of inhibition zone, and fungi (Candida albicans) with 9-10 mm of inhibition zone.

A Cellulose-Type Carrier for Intimate Coupling Photocatalysis and Biodegradation

Intimate coupling photocatalysis and biodegradation treatment technology is an emerging technology in the treatment of refractory organic matter, and the carrier plays an important role in this technology. In this paper, sugarcane cellulose was used as the basic skeleton, absorbent cotton was used as a reinforcing agent, anhydrous sodium sulfate was used as a pore-forming agent to prepare a cellulose porous support with good photocatalytic performance, and nano-TiO₂ was loaded onto it by a low-temperature bonding method. The results showed that the optimal preparation conditions of cellulose carriers were: cellulose mass fraction 1.0%; absorbent cotton 0.6 g; and Na₂SO₄ 60 g. The SEM, EDS and XPS characterization further indicated that the nano-TiO₂ was uniformly loaded onto the cellulose support. The degradation experiments of Rhodamine B showed that the nano-TiO₂-loaded composite supports had good photocatalytic performance. The degradation rate of 1,2,4-trichlorobenzene was more than 92% after 6 cycles, and the experiment of adhering a large number of microorganisms on the carriers before and after the reaction showed that the cellulose-based carriers obtained the required photocatalytic performance and stability, which is a good cellulose porous carrier.

Block Copolymer and Cellulose Templated Mesoporous TiO2-SiO2 Nanocomposite as Superior Photocatalyst

A dual soft-templating method was developed to produce highly crystalline and mesoporous TiO2-SiO2 nanocomposites. Pluronic F127 as the structure-directing agent and pure cellulose as the surface area modifier were used as the templating media. While Pluronic F127 served as the sacrificing media for generating a mesoporous structure in an acidic pH, cellulose templating helped to increase the specific surface area without affecting the mesoporosity of the TiO2-SiO2 nanostructures. Calcination at elevated temperature removed all the organics and formed pure inorganic TiO2-SiO2 composites as revealed by TGA and FTIR analyses. An optimum amount of SiO2 insertion in the TiO2 matrix increased the thermal stability of the crystalline anatase phase. BET surface area measurement along with low angle XRD revealed the formation of a mesoporous structure in the composites. The photocatalytic activity was evaluated by the degradation of Rhodamine B, Methylene Blue, and 4-Nitrophenol as the model pollutants under solar light irradiation, where the superior photo-degradation activity of Pluronic F127/cellulose templated TiO2-SiO2 was observed compared to pure Pluronic templated composite and commercial Evonik P25 TiO2. The higher photocatalytic activity was achieved due to the higher thermal stability of the nanocrystalline anatase phase, the mesoporosity, and the higher specific surface area.

Preparation of flexible and UV-blocking films from lignin-containing cellulose incorporated with tea polyphenol/citric acid

Lignin-containing bamboo cellulose, fractionated from a pilot-scale microwave liquefaction of bamboo was dissolved in tetrabutylammonium acetate/dimethyl sulfoxide (TBAA/DMSO) for the fabrication of highly flexible, transparent and UV-blocking films. Tea polyphenol (TP) or citric acid (CA) was added during the dissolving process in order to modify the film's properties. The results showed that the addition of TP obviously improved the elongation at break (triple that of the control) and UV-blocking ability of the films. Both the addition of TP and CA could increase the water contact angle of the films. The films incorporated with TP and CA were much more thermal stable than previously reported similar films. The proposed film fabrication mechanism revealed that stable hydrogen bonds formed between the lignin-cellulose matrix and TP/CA, resulting in the enhancement on the properties of the films. This present study showed that lignin-containing cellulose with the incorporation of TP/CA had great potential in the preparation of films in place of plastic.

Heterogeneous Advanced Oxidation Processes: Current Approaches for Wastewater Treatment

Nowadays, water pollution is one of the most dangerous environmental problems in the world. The presence of the so-called emerging pollutants in the different water bodies, impossible to eliminate through conventional biological and physical treatments used in wastewater treatment plants due to their persistent and recalcitrant nature, means that pollution continues growing throughout the world. The presence of these emerging pollutants involves serious risks to human and animal health for aquatic and terrestrial organisms. Therefore, in recent years, advanced oxidation processes (AOPs) have been postulated as a viable, innovative and efficient technology for the elimination of these types of compounds from water bodies. The oxidation/reduction reactions triggered in most of these processes require a suitable catalyst. The most recent research focuses on the use and development of different types of heterogeneous catalysts, which are capable of overcoming some of the operational limitations of homogeneous processes such as the generation of metallic sludge, difficult separation of treated water and narrow working pH. This review details the current advances in the field of heterogeneous AOPs, Fenton processes and photocatalysts for the removal of different types of emerging pollutants.

Photocatalytic materials immobilized on recycled supports and their role in the degradation of water contaminants: A timely review

Global concern about environmental pollution has increased in recent times due to the cumulative harmful impact on the human health occasioned by the diverse toxic substances released into the environment. Water reduced availability for human consumption and its pollution have been paid so much attention due to their relevance in agricultural and industrial activities. In this context, the advanced oxidation processes for removing contaminants from water, more specifically photocatalytic processes, have displayed their usefulness due to features such as easy application, low-cost, harmless effects and sustainable decontamination efficiency. This timely review is centered on worldwide studies, where efforts aimed at employing recycled materials as supports for purification applications such as the removal of different contaminants (dyes, pharmaceutical contaminants, and heavy metals) dissolved in aqueous environments have been reported. Materials like polyethylene terephthalic (PET), polystyrene (PS), disposal textile fabrics, newspapers, aluminum soda cans, rubber, waste electronic and electric components and used batteries have been employed either as supports for immobilizing catalysts or as photocatalysts. The present work offers a discussion of the ways through which photocatalytic composites have been immobilized or produced, employed characterization techniques, removal efficiencies achieved during photocatalytic degradation and possible degradation mechanism of pollutants; not only the highlights of all these studies are discussed, but also paths for future research works that could help improve the reported results are suggested. These new practical tools stand as novel sustainable strategies for the removal of emerging contaminants reusing waste flexible materials.

Effect of carbon nitride synthesized by different modification strategies on the performance of carbon nitride/PVDF photocatalytic composite membranes

Carbon nitride (CN)/polyvinylidene fluoride (PVDF) photocatalytic composite membrane (PCM) is considered as a promising candidate to improve the anti-fouling characteristic of conventional PVDF membrane and overcome the difficulty encountered during recovery of powder catalyst simultaneously. However, the effects of differently-modified CN on PCM and its mechanism are still unclear. In this study, bulk-CN (BCN), carbon defects CN (CCN), nitrogen defect CN (DCN), mesoporous CN (MCN), and nitrogen-rich CN (NCN) were incorporated into PVDF by phase inversion method. The influence of changes in the physical and chemical properties of CN, including hydrophilic groups, photocatalytic activity, and particle size, on the permeability, anti-fouling characteristic, and photocatalytic self-cleaning activity of CN/PVDF was systematically analyzed. The mechanism of excellent performance of PCM was revealed by experimental test and theoretical calculation. The flux of PCM was significantly improved by increasing the hydrophilic group on modified CN. However, the differences in particle size and interaction between different types of modified CN and PVDF chains endowed the CN/PVDF with different porosity. DCN/PVDF showed high porosity and hydrophilicity, leading to high water flux and rejection rate of 293.6 L (m² h)^-1 and 90.1%, respectively. Compared to pure PVDF, the flux recovery rate of DCN₃₀/PVDF increased by 27.6%, and the irreversible fouling decreased from 36.9% to 9.2%. The modified CN/PVDF showed excellent photocatalytic activity for the removal of cefotaxime (CFX) and E. coli. Owing to the narrow band gap of DCN, large specific surface area, and low photogenerated carrier recombination rate, the CFX removal rate reached 99% in 2 h, and E. coli inactivation achieved 3.7 log within 4 h via DCN₃₀/PVDF.

Waste Reutilization in Polymeric Membrane Fabrication: A New Direction in Membranes for Separation

In parallel to the rapid growth in economic and social activities, there has been an undesirable increase in environmental degradation due to the massively produced and disposed waste. The need to manage waste in a more innovative manner has become an urgent matter. In response to the call for circular economy, some solid wastes can offer plenty of opportunities to be reutilized as raw materials for the fabrication of functional, high-value products. In the context of solid waste-derived polymeric membrane development, this strategy can pave a way to reduce the consumption of conventional feedstock for the production of synthetic polymers and simultaneously to dampen the negative environmental impacts resulting from the improper management of these solid wastes. The review aims to offer a platform for overviewing the potentials of reutilizing solid waste in liquid separation membrane fabrication by covering the important aspects, including waste pretreatment and raw material extraction, membrane fabrication and characterizations, as well as the separation performance evaluation of the resultant membranes. Three major types of waste-derived polymeric raw materials, namely keratin, cellulose, and plastics, are discussed based on the waste origins, limitations in the waste processing, and their conversion into polymeric membranes. With the promising material properties and viability of processing facilities, recycling and reutilization of waste resources for membrane fabrication are deemed to be a promising strategy that can bring about huge benefits in multiple ways, especially to make a step closer to sustainable and green membrane production.

Curing of Cellulose Hydrogels by UV Radiation for Mechanical Reinforcement

The use of biomaterials as a replacement for thermoplastic polymers is an environmentally sound strategy. In this work, hydrogels of cellulose isolated from wheat husk were modified by UV irradiation (353 nm) to improve mechanical performance. The cellulose was dissolved with a solvent system N,N-dimethylacetamide/lithium chloride (DMAc/LiCl). Infrared spectroscopy showed that the peak height at 1016 cm^-1, associated with the C-O bonds of the glycosidic ring, increases with irradiation time. It was determined that the increase in this signal is related to photodegradation, the product of a progressive increase in exposure to UV radiation. The viscoelastic behavior, determined by dynamic mechanical analysis and rotational rheometry, was taken as the most important parameter of this research, showing that the best results are recorded with 15 min of UV treatment. Therefore, at this time or less, the chemical crosslinking is predominant over the photodegradation, producing an increase in the modules, while with 20 min the photodegradation is such that the modules suffer a significant reduction.

BiFeO3 immobilized within liquid natural rubber-based hydrogel with enhanced adsorption-photocatalytic performance

Semiconductor materials have shown a good photocatalytic behaviour for the photodegradation of organic pollutants. In this work, maleated liquid natural rubber (MLNR) based hydrogel supported bismuth ferrite (BiFeO₃) as photocatalyst was successfully synthesized by crosslinking with acrylic acid (AAc) assisted by the ultrasonication method to study the efficiency for the removal of methylene blue (MB) dye in wastewater. Response surface methodology (RSM) was used to optimize the parameters for adsorption of the methylene blue (MB) dye compound, whereby the effects of the initial concentration of MB and the adsorption time were examined to obtain a quadratic model for the respective hydrogel composite. The prepared composite sample was characterized by Fourier Transform Infrared (FTIR) spectroscopy, Scanning Electron Microscopy-Energy Dispersive X-ray (SEM-EDX) and X-ray Diffraction (XRD) analysis. Remarkable improvement for removal of methylene blue (99% removal) was found within 3 h adsorption time with a MLNR/AAc-BiFeO₃ hydrogel composite as compared to the pristine hydrogel. A synergistic mode of dye removal by adsorption and photodegradation is proposed. Based on the isotherm and kinetic study conducted, it was found that Freundlich isotherm model and a pseudo second-order kinetic model was best fitted for adsorption of MB dye. The MLNR/AAc-BiFeO₃ composite maintains its removal efficiency after 5 cycles without the necessity of post-treatment separation. Therefore, it is crucial to note that the resultant low-cost MLNR/AAc-BiFeO₃ hydrogel composite in this study offers excellent potential for water and wastewater treatment applications with improved recyclability and recovery.

Floating ZnO QDs-Modified TiO2/LLDPE Hybrid Polymer Film for the Effective Photodegradation of Tetracycline under Fluorescent Light Irradiation: Synthesis and Characterisation

In this work, mesoporous TiO₂-modified ZnO quantum dots (QDs) were immobilised on a linear low-density polyethylene (LLDPE) polymer using a solution casting method for the photodegradation of tetracycline (TC) antibiotics under fluorescent light irradiation. Various spectroscopic and microscopic techniques were used to investigate the physicochemical properties of the floating hybrid polymer film catalyst (8%-ZT@LLDPE). The highest removal (89.5%) of TC (40 mg/L) was achieved within 90 min at pH 9 due to enhanced water uptake by the LDDPE film and the surface roughness of the hybrid film. The formation of heterojunctions increased the separation of photogenerated electron-hole pairs. The QDs size-dependent quantum confinement effect leads to the displacement of the conduction band potential of ZnO QDs to more negative energy values than TiO₂. The displacement generates more reactive species with higher oxidation ability. The highly stable film photocatalyst can be separated easily and can be repeatedly used up to 8 cycles without significant loss in the photocatalytic ability. The scavenging test indicates that the main species responsible for the photodegradation was O₂^●−. The proposed photodegradation mechanism of TC was demonstrated in further detail based on the intermediates detected by LC-time-of-flight/mass spectrometry (LC/TOF-MS).

Novel covalent organic framework/PVDF ultrafiltration membranes with antifouling and lead removal performance

Membrane separation technology is recognized as a competitive approach to remove Pb²⁺ from water system due to its high efficiency and low operating cost. In present study, a simple and facile approach was developed to fabricate covalent organic framework (COF) modified PVDF ultrafiltration membranes with comprehensive antifouling property and superior Pb²⁺ removal ability. Herein, COF was synthesised in a homogenous PVDF/DMAc solution to fabricate hydrophilic COF modified PVDF ultrafiltration membranes with the Pb²⁺ removal property. The filtration test demonstrated that the COF modified PVDF ultrafiltration membranes exhibited excellent antifouling property and high water flux. Moreover, the membranes showed remarkable potential for treating Pb²⁺-containing water. The removal efficiency was determined at 92.4%, and its removal efficiency was 87.5% at the fourth treatment cycle with Pb²⁺-containing water. The present work provides a valuable platform for further development of efficient composite membranes for the treatment of Pb²⁺-containing water.

Removal of Pharmaceutical Contaminants in Wastewater Using Nanomaterials: A Comprehensive Review

BACKGROUND

The limitless presence of pharmaceutical contaminants in discharged wastewater has emerged as a threat to aquatic species and humans. Their presence in drinking water has although raised substantial concerns, very little is known about the fate and ecological impacts of these pollutants. As a result, these pollutants are inevitably introduced to our food chain at trace concentrations. Unfortunately, the conventional wastewater treatment techniques are unable to treat pharmaceuticals completely with practical limitations. The focus has now been shifted towards nanotechnology for the successful remediation of these persistent pollutants. Thus, the current review specifically focuses on providing readers brief yet sharp insights into applications of various nanomaterials for the removal of pharmaceutical contaminants.

METHODS

An exhaustive collection of bibliographic database was done with articles having high impact and citations in relevant research domains. An in-depth analysis of screened papers was done through standard tools. Studies were categorized according to the use of nanoscale materials as nano-adsorbents (graphene, carbon nanotubes), nanophotocatalysts (metal, metal oxide), nano-filtration, and ozonation for promising alternative technologies for the efficient removal of recalcitrant contaminants.

RESULTS

A total of 365 research articles were selected. The contemporary advancements in the field of nanomaterials for drinking and wastewater treatment have been thoroughly analyzed along with their future perspectives.

CONCLUSION

The recommendations provided in this article will be useful to adopt novel strategies for on-site removal of the emerging contaminants in pharmaceutical effluents and related industries.

Intensified Photocatalytic Degradation of Solophenyl Scarlet BNLE in Simulated Textile Effluents Using TiO2 Supported on Cellulosic Tissue

The Heterogeneous photocatalysis, increasingly used in effluent purification, is attracting more and more attention by the development of new photocatalytic materials based on semiconductors deposited on various supports. In this work, TiO2 supported on cellulosic fiber was prepared and characterized by different analytical techniques such as X-ray Photoelectron Spectrometry and Brunauer-Emmett-Teller surface area. Its photocatalytic activity was investigated for the degradation of Solophenyl Scarlet BNLE (SS), an organic pollutant present in textile effluents. Several conditions were investigated such as adsorption under UV and visible irradiation, catalyst recyclability, the simulated effluent pH and the presence of H2O2 as an oxidant agent. Results showed that under UV light, the removal of SS decreased significantly with increasing initial dye concentration. For an initial concentration of 5 mg/L, SS degradation was reached more than 95 % after 2 hours of treatment (neutral pH, T = 20 °C). The supported TiO2 on cellulose remains effective over four cycles of dye treatment. In the presence of H2O2, the degradation process was inhibited with increasing the molar ratio [H2O2]/[SS]0 from 5 to 30. The kinetic modeling showed that the removal of this pollutant followed a pseudo-first-order model (Langmuir-Hinshelwood) with a regression coefficient (R2) value of 0.984.

Design and Construction of Ag@MOFs Immobilized PVDF Ultrafiltration Membranes with Anti-bacterial and Antifouling Properties

In this work, Ag nanoparticle loading Mg(C10H16O4)2(H2O)2(Ag@MOF) composite material was successfully prepared by a facile strategy, and subsequently Ag-MOFs were used to modify the PVDF ultrafiltration membranes to obtain fouling resistance and higher water flux. The as-prepared PVDF membranes were systematically characterized by a series of analytical techniques such as Water Contact Angle (CA), Scanning Electron Microscopy (SEM), and SEM-mapping. Furthermore, the performance of membranes on antibacterial properties, the pure water flux, and fouling resistance was investigated in detail. Those results showed that the membrane modified by Ag@MOFs containing 30% Ag had the higher anti-bacterial performance, and the clear zone could be increased to 10 mm in comparison with that of blank membrane. Meanwhile, the pure water flux of Ag@MOF membranes increased from 85 L/m2 h to 157 L/m2 h, and the maximum membrane flux recovery rate (FRR) of 95.7% was obtained using SA as pollutant, which is attributed to the introduction of Ag@MOF composite material. Based on the above experimental results, it can be found that the Ag-MOF membranes displayed the excellent antibacterial activity, high water flux, and fine fouling resistance. This work provides a facile strategy to fabricate the Ag@MOFs modified membranes, and it shows an excellent anti-bacterial and water flux performance.

Single step synthesis of Janus nano-composite membranes by atmospheric aerosol plasma polymerization for solvents separation

Solvent permeation across membranes is limited due to physical resistance to diffusion from the selective layer within the membrane and to plasticizing effects generated by the solvent molecules onto the polymeric macromolecular matrix. Nano-composite thin film membranes provide promising routes to generate controlled microstructural separation materials with higher selectivities and permeabilities. Here, the fabrication of nano-composite based on octamethyl-polyhedral oligomeric silsesquioxane - hexamethyldisiloxane thin film membranes is demonstrated by aerosol assisted atmospheric plasma deposition onto pre-formed nano-porous membrane supports for the first time. Stable, atomically smooth and continuous solid films with controllable thickness down to 50 nm were achieved. The deposition process allowed for the control of the wettability of the surfaces to water and organic solvents, leading to the generation of hydrophobic but alcohol-philic surfaces. The liquid entry pressure of the films to water was found to be 8 bar from plasma polymerization as oppose to 3 bar for the bare nano-porous support only. In addition, the ideal separation selectivity for ethanol to water, up to 6.5, highlight the impact of both the surface energy and level of cross-linking of the hexamethyldisiloxane nanostructures on the diffusion mechanisms. This new atmospheric plasma deposition strategy opens-up cost-effective and environmentally friendly routes for the design of the smart Janus membrane with customizable properties and performance.

Synthesis of nanostructured titanium dioxide layer onto kaolin hollow fibre membrane via hydrothermal method for decolourisation of reactive black 5

Hydrothermal method has been proven to be an effective method to synthesise the nanostructured titanium dioxide (TiO₂) with good morphology and uniform distribution at low temperature. Despite of employing a well-known and commonly used glass substrate as the support to hydrothermally synthesise the nanostructured TiO₂, this study emphasised on the application of kaolin hollow fibre membrane as the support for the fabrication of kaolin/TiO₂ nanorods (TNR) membrane. By varying the hydrothermal reaction times (2 h, 6 h, and 10 h), the different morphology, distribution, and properties of TiO₂ nanorods on kaolin support were observed by field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX), atomic force microscope (AFM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). It was found that the well-dispersed of TiO₂ nanorods have improved the surface affinity of kaolin/TNR membrane towards water, allowing kaolin/TNR membrane prepared from 10 h of hydrothermal reaction to exhibit the highest water permeation of 165 L/h.m².bar. In addition, this prepared membrane also showed the highest photocatalytic activity of 80.3% in the decolourisation of reactive black 5 (RB5) under UV irradiation. On top of that, the kaolin/TNR membrane prepared from 10 h of hydrothermal reaction also exhibited a good resistance towards photocorrosion, enabling the reuse of this membrane for three consecutive cycles of photocatalytic degradation of RB5 without showing significant reduction in photocatalytic efficiency towards the decolourisation of RB5.

Nanocomposite Membrane with Polyethylenimine-Grafted Graphene Oxide as a Novel Additive to Enhance Pollutant Filtration Performance

Synthetic membranes often suffer ubiquitous fouling as well as a trade-off between permeability and selectivity. However, emerging materials which are able to mitigate membrane fouling and break the permeability and selectivity trade-off are urgently needed. A novel additive, GO-PEI, bearing a positive charge and hydrophilic nature was prepared by the covalent grafting of polyethylenimine (PEI) molecules with graphene oxide (GO) nanosheets, which later was blended with bulk poly(ether sulfone) (PES) to fabricate the graphene containing nanocomposite membranes (NCMs). Strong π-π interactions contributed to the uniform dispersion of GO-PEI nanosheets in bulk PES to form the asymmetric structure of NCM without leaching. The ratio of the GO-PEI additive regulated the surface charge and hydrophilicity of NCMs. To filter charged proteins, the designed NCM exhibited a high permeability (flux) and high selectivity (retention) while showing resistance to fouling by the charged proteins, which could be attributed to the asymmetric structure and composition of the NCM that the porous internal and surface composited with the GO-PEI additive was responsible for the NCM's high flux; thereafter, the electrostatic attraction of the NCM surface to the charged pollutant enhanced the solute/water selectivity; finally, the synergistic effect of the hydrophilic and charged functional groups of the GO-PEI contributed to the formation of a dense hydration layer on the membrane surface thereby reducing membrane fouling. The NCM functionalized with the GO-PEI additive demonstrated potential for high-performance pollutant removal in water and wastewater treatments.