A novel bimetallic MIL-101(Cr, Mg) with high CO2 adsorption capacity and CO2/N2 selectivity

CO2 Adsorption by CMK-3 at Low Temperatures and High Pressure to Reduce the Greenhouse Effect

In this study, the maximum CO2 capture capacity of an ordered mesoporous carbon (CMK-3) was evaluated at high pressure (35 atm) and several temperatures (0, 10, 20, and 35 °C). CMK-3 was synthesized with the hard template method (silica SBA-15) using furfuryl alcohol and toluene as carbon sources. The CO2 adsorption isotherms were fitted to the following adsorption theories: Freundlich, Langmuir, Sips, Toth, Dubinin-Radushkevich, and Temkin. The maximum capture capacity (726.7 mg·g-1) was achieved at 0 °C and 34 atm. The results of the study of successive adsorption-desorption cycles showed that multi-cycle reversible gas capture processes could be used in optimal temperature and pressure conditions. It was determined that 0.478 g of CMK-3 would be required to reduce the CO2 concentration in 1 m3 of air to pre-industrial levels (280 ppm). The obtained results may contribute to technological developments for the mitigation of human impacts on the environment through the capture of atmospheric CO2.

Construction of Zn-Cu bimetallic metal-organic frameworks for carbon dioxide capture

Bimetallic metal-organic frameworks (MOFs) have shown more impressive performance in gas adsorption compared with monometallic MOFs. Herein, a Cu-Zn bimetallic metal-organic framework (Zn/Cu-BTC) was synthesized via a one-pot method, and its structure, thermal stability and CO2 adsorption property were investigated and compared with those of corresponding monometallic Cu-BTC and Zn-BTC. The results showed that Zn/Cu-BTC has a specific ortho-octahedral crystal morphology with a unique X-ray diffraction peak, the atomic ratio of Zn to Cu is about 1 : 5, and it remained stable at a temperature up to 490 K. In Zn/Cu-BTC, Cu2+ played a role in increasing the specific surface area and porosity of the MOF and improving the gas adsorption performance. The CO2 adsorption of Zn/Cu-BTC is lower than that of Cu-BTC but much higher than that of Zn-BTC, and CO2 adsorption heat was 30.52 kJ mol-1, which indicated physical adsorption. In addition, Zn/Cu-BTC had higher CO2/N2 adsorption selectivity compared with Zn-BTC and Cu-BTC, with a maximum value of 17. This study can be a reference for the research on improving the adsorption selectivity of gases by constructing bimetallic MOFs.

Use of Periodic Mesoporous Organosilica-Benzene Adsorbent for CO2 Capture to Reduce the Greenhouse Effect

The CO2 adsorption of a phenylene-bridged ordered mesoporous organosilica (PMO-benzene) was analyzed. The maximum capture capacity was 638.2 mg·g-1 (0 °C and 34 atm). Approximately 0.43 g would be enough to reduce the amount of atmospheric CO2 in 1 m3 to pre-industrial levels. The CO2 adsorption data were analyzed using several isotherm models, including Langmuir, Freundlich, Sips, Toth, Dubinin-Radushkevich, and Temkin models. This study confirmed the capability of this material for use in reversible CO2 capture with a minimal loss of capacity (around 1%) after 10 capture cycles. Various techniques were employed to characterize this material. The findings from this study can help mitigate the greenhouse effect caused by CO2.

Robust and stable superhydrophilic MIL-101 (Cr)-coated copper mesh for highly efficient oil/water emulsion separation

In this study, dip coating method was investigated to prepare superhydrophilic MIL-101 (Cr)-coated copper mesh for highly efficient oil/water emulsion separation. To increase the surface area of synthesized MIL-101 (Cr), a purification procedure was developed to remove unreacted H2BDC crystals present in the channel of the initial MIL-101 (Cr) sample synthesized. After that, a dispersing solution of MIL-101 (Cr) was needed to coat on the copper mesh. Thermoplastic polyurethane (TPU) was used as a binder in this procedure. The prepared membranes of M1 (once coated mesh) to M6 (six times coated mesh) were performed to separate oil/water emulsion effectively. Contact angle tests showed the superhydrophilic/underwater superoleophobic wettability behavior of MIL-101 (Cr)-coated copper meshes. The wetting mechanism of the prepared membranes is mostly relevant to the surface functional groups of purified MIL-101 (Cr). Also, the roughness of the nanostructured coated membranes was improved because of the uniform coating of MIL-101 (Cr) which is integrated into hydrophilic TPU. Oil/water separation results showed that M2 (twice coated mesh) showed the maximum amount of water flux (83076 L m-2 h-1) in oil/water separation and M3 (three times coated mesh) had the best performance of oil/water emulsion with 99.99% separation efficiency.

Bimetallic Coordination Polymers: Synthesis and Applications in Biosensing and Biomedicine

Bimetallic coordination polymers (CPs) have two different metal ions as connecting nodes in their polymer structure. The synthesis methods of bimetallic CPs are mainly categorized into the one-pot method and post-synthesis modifications according to various needs. Compared with monometallic CPs, bimetallic CPs have synergistic effects and excellent properties, such as higher gas adsorption rate, more efficient catalytic properties, stronger luminescent properties, and more stable loading platforms, which have been widely applied in the fields of gas adsorption, catalysis, energy storage as well as conversion, and biosensing. In recent years, the study of bimetallic CPs synergized with cancer drugs and functional nanomaterials for the therapy of cancer has increasingly attracted the attention of scientists. This review presents the research progress of bimetallic CPs in biosensing and biomedicine in the last five years and provides a perspective for their future development.

Synthesis and performance analysis of zeolitic imidazolate frameworks for CO2 sensing applications

In this paper, we investigate the potential use of Zeolitic Imidazolate Frameworks (ZIF-8) as a sensing material for CO2 detection. Three synthesis techniques are considered for the preparation of ZIF-8, namely room temperature, microwave-assisted, and ball milling. The latter is a green and facile alternative for synthesis with its solvent-free, room-temperature operation. In addition, ball milling produces ZIF-8 samples with superior CO2 adsorption and detection characteristics, as concluded from fluorescence measurements. Characterization tests including X-ray diffraction (XRD), Fourier transform infrared (FTIR), Thermogravimetric analysis (TGA), Field emission scanning electron microscopy (FE-SEM) and Energy-dispersive X-ray spectroscopy (EDS) are conducted to inspect the structural morphology, the thermal stability, and elements content of the ZIF-8 samples obtained from the different aforementioned synthesis techniques. The characterization tests revealed the appearance of a new phase of ZIF-8 which is ZIF-L when deploying the ball milling technique with different structure, morphology, response to CO2 exposure and thermal stability when compared to its counterparts. Fluorescence measurements are carried out to evaluate the limit of detection (LOD), selectivity, and recyclability of the different ZIF-8 samples. The LOD of the ZIF-8 sample synthesized based on ball milling synthesis technique is 815.2 ppm, while LODs of the samples obtained from microwave and room temperature-based synthesis techniques are 1780.6 ppm and 723.8 ppm, respectively. This indicates that the room temperature and ball milling produced MOFs have comparable LODs. However, the room temperature procedure requires the use of a harmful solvent. The range of LOD demonstrates the suitable use of ZIF-8 for indoor air quality monitoring and other industrial applications.

Graphene-grafted bimetallic MOF membranes for hazardous & toxic contaminants treatment

Development of membrane with improved carbon dioxide (CO2) gas separation capability is a significant challenge. However, the fabrication of membrane that efficiently separate and purification CO2-containing gases has been the focus of global attention. Cellulose Acetate (CA) has robust reinforcing characteristics when incorporated within a suitable polymer matrix. This work focus on the synthesis of novel mixed matrix membranes (MMMs) by introducing Graphene-grafted bimetallic MOFs in Cellulose Acetate polymer. The graphene-grafted bimetallic MOF (GG-BM MOFs) was prepared by a hydrothermal technique. Whereas, the solution casting approach used to fabricate membranes. The 1-5 wt% of GG-BM MOFs incorporated into the CA matrix. The mechanical, hydrophilicity and adsorption characteristics of fabricated MMMs were investigated. The crystallinity of MMM enhanced after the addition of GG-BM MOFs. In addition, the mechanical characteristics of MMMs were improved with the incorporation of GG-BM MOFs inside the polymer matrix. Maximum stress and strain was obtained for 2 wt% MMM (36.4 N/mm2 and 11% respectively). The CO2 adsorption performance was evaluated at 10 bar and 45 °C. The FTIR results represent insignificant bond shifting with the addition GG-BM MOFs at these conditions. The overall results showed that MMMs containing 2 wt% GG-BM MOFs have good adsorption properties for CO2 i.e 3.15 wt% of CO2. The MMMs have shown a decrease in the mechanical properties and CO2 adsorption at the higher GG-BM MOFs loading due to the presence of agglomeration which was confirmed through SEM. Thus, the addition of GG-BM MOFs in the CA matrix positively altered the physicochemical characteristics of the resulting MMMs, which could assist them in achieving remarkable CO2 adsorption at 2 wt%.

Room Temperature Synthesis Mediated Porphyrinic NanoMOF Enables Benchmark Electrochemical Biosensing

Leveraging size effects, nanoparticles of metal-organic frameworks, nanoMOFs, have recently gained traction, amplifying their scopes in electrochemical sensing. However, their synthesis, especially under eco-friendly ambient conditions remains an unmet challenge. Herein, an ambient and fast secondary building unit (SBU)-assisted synthesis (SAS) route to afford a prototypal porphyrinic MOF, Fe-MOF-525 is introduced. Albeit the benign room temperature conditions, Fe-MOF-525(SAS) nanocrystallites obtained are of ≈30 nm size, relatively smaller than the ones conventional solvothermal methods elicit. Integrating Fe-MOF-525(SAS) as a thin film on a conductive indium tin oxide (ITO) surface affords Fe-MOF-525(SAS)/ITO, an electrochemical biosensor. Synergistic confluence of modular MOF composition, analyte-specific redox metalloporphyrin sites, and crystal downsizing contribute to its benchmark voltammetric uric acid (UA) sensing. Showcasing a wide linear range of UA detection with high sensitivity and low detection limit, this SAS strategy coalesces ambient condition synthesis and nanoparticle size control, paving a green way to advanced sensors.

Highly efficient and selective CO2 capture of Li2CO3- and (Li-K)2CO3-based porous carbon composites

In this study, Li₂CO₃- and (Li-K)₂CO₃-based porous carbon composites were synthesized from terephthalic acid, lithium hydroxide and sodium hydroxide through calcination at different temperatures. These materials were fully characterized through X-ray diffraction, Raman spectroscopy, and nitrogen adsorption and desorption. Results showed that the excellent CO₂ capture capacities of LiC-700 °C and LiKC-600 °C were 140 and 82 mg CO₂ g^-1 at 0 °C and 25 °C, respectively. Additionally, it is calculated that the selectivity of LiC-600 °C and LiKC-700 °C with a CO₂/N₂ (15 : 85) mixture was about 27.41 and 15.04, respectively. Therefore, Li₂CO₃- and (Li-K)₂CO₃-based porous carbon materials could be used to effectively capture CO₂ with high capacity and high selectivity.

CuBTC Metal-Organic Framework Decorated with FeBTC Nanoparticles with Enhance Water Stability for Environmental Remediation Applications

Metal-organic frameworks (MOFs) based on Cu-benzene tricarboxylate (CuBTC) are widely used for gas storage and removal applications. However, they readily lose their crystal structures under humid conditions, limiting their practical applications. This structural decomposition reduces the specific surface area, gas adsorption capability, and recyclability of CuBTC considerably. In this study, a stable MOF against water exposure was designed based on FeBTC nanoparticle-covered CuBTC (FeCuBTC). A simple one-pot solvothermal process that enables the epitaxial growth of FeBTC on the CuBTC surface was proposed. Structural and morphological analyses after water exposure revealed that the water stability of FeCuBTC was better than that of CuBTC, which completely lost its crystallinity. This observed improvement in the water stability of the synthesized MOF proved to be beneficial for the adsorption of formaldehyde under humid conditions. The proposed strategy herein is simple yet highly effective in the design of hetero-bimetallic MOFs with considerably improved water resistance and extended applicability for environmental remediation processes.

Synthesis and Peroxide Activation Mechanism of Bimetallic MOF for Water Contaminant Degradation: A Review

Metal-organic framework (MOF) materials possess a large specific surface area, high porosity, and atomically dispersed metal active sites, which confer excellent catalytic performance as peroxide (peroxodisulfate (PDS), peroxomonosulfate (PMS), and hydrogen peroxide (H₂O₂)) activation catalysts. However, the limited electron transfer characteristics and chemical stability of traditional monometallic MOFs restrict their catalytic performance and large-scale application in advanced oxidation reactions. Furthermore, the single-metal active site and uniform charge density distribution of monometallic MOFs result in a fixed activation reaction path of peroxide in the Fenton-like reaction process. To address these limitations, bimetallic MOFs have been developed to improve catalytic activity, stability, and reaction controllability in peroxide activation reactions. Compared with monometallic MOFs, bimetallic MOFs enhance the active site of the material, promote internal electron transfer, and even alter the activation path through the synergistic effect of bimetals. In this review, we systematically summarize the preparation methods of bimetallic MOFs and the mechanism of activating different peroxide systems. Moreover, we discuss the reaction factors that affect the process of peroxide activation. This report aims to expand the understanding of bimetallic MOF synthesis and their catalytic mechanisms in advanced oxidation processes.

An Economical Modification Method for MIL-101 to Capture Radioiodine Gaseous: Adsorption Properties and Enhancement Mechanism

Radioactive iodine is one of the inevitable by-products of nuclear energy application. However, it is a great threat to public health and the adsorbent needs to be adopted for removing the radioactive iodine. The iodine adsorbent needs to have some advantages, such as simple preparation method, low cost, high absorption capacity, and recyclable utilization. In order to meet the above requirements, the etched material of institute Lavoisier 101 (MIL-101) was prepared to absorb the gaseous iodine. After the MIL-101 is etched, the iodine adsorption performance has been greatly improved. The iodine adsorption experiment of etched MIL-101 with different etching time (1 h, 3 h, 4 h, and 6 h) was completed, the results show that the optimal etching time is 4 hours and the capture capacity of the etched MIL-101 is 371 wt%, which is about 22% higher than that of original MIL-101. The experiment results of XRD, FT-IR, and XPS prove that the components and structure of etched MIL-101 are accordable with those of MIL-101. The surface roughness is introduced in this work. The pore roughness is also an important factor to the adsorption capacity, and the related research also supports this conclusion. Furthermore, after iodine is absorbed, etched MIL-101 can be treated by ethanol for iodine release, and the etched MIL-101 has satisfied recyclability within three cycles. Compared with MIL-101, etched MIL-101 not only had good reversible adsorption of iodine but also can adsorb low-concentration iodine. The etched MIL-101 has a broad application prospect in nuclear emergency response and radiation detection.

Bimetallic Metal-Organic Frameworks (BMOF) and BMOF- Incorporated Membranes for Energy and Environmental Applications

Bimetallic metal organic frameworks (BMOFs) are a class of crystalline solids and their structure comprises two metal ions in the lattice. BMOFs show a synergistic effect of two metal centres and enhanced properties compared to MOFs. By controlling the composition and relative distribution of two metal ions in the lattice the structure, morphology, and topology of BMOFs could be regulated resulting in an improvement in the tunability of pore structure, activity, and selectivity. Thus, developing BMOFs and BMOF incorporated membranes for applications such as adsorption, separation, catalysis, and sensing is a promising strategy to mitigate environmental pollution and address the looming energy crisis. Herein we present an overview of recent advancements in the area of BMOFs and a comprehensive review of BMOF incorporated membranes reported to date. The scope, challenges as well as future perspectives for BMOFs and BMOF incorporated membranes are presented.

Hierarchical Metal-Organic Aerogel as a Highly Selective and Sustainable CO2 Adsorbent

Typical amorphous aerogels pose great potential for CO₂ adsorbents with high surface areas and facile diffusion, but they lack well-defined porosity and specific selectivity, inhibiting utilization of their full functionality. To assign well-defined porous structures to aerogels, a hierarchical metal-organic aerogel (HMOA) is designed, which consists of well-defined micropores (d ∼ 1 nm) by coordinative integration with chromium(III) and organic ligands. Due to its hierarchical structure with intrinsically flexible coordination, the HMOA has excellent porous features of a high surface area and a reusable surface with appropriate binding energy for CO₂ adsorption. The HMOA features high CO₂ adsorption capacity, high CO₂/N₂ IAST selectivity, and vacuum-induced surface regenerability (100% through 20 cycles). Further, the HMOA could be prepared via simple ambient drying methods while retaining the microporous network. This unique surface-tension-resistant micropore formation and flexible coordination systems of HMOA make it a potential candidate for a CO₂ adsorbent with industrial scalability and reproducibility.

CO2 Capture from High-Humidity Flue Gas Using a Stable Metal–Organic Framework

The flue gas from fossil fuel power plants is a long-term stable and concentrated emission source of CO2, and it is imperative to reduce its emission. Adsorbents have played a pivotal role in reducing CO2 emissions in recent years, but the presence of water vapor in flue gas poses a challenge to the stability of adsorbents. In this study, ZIF-94, one of the ZIF adsorbents, showed good CO2 uptake (53.30 cm3/g), and the calculated CO2/N2 (15:85, v/v) selectivity was 54.12 at 298 K. Because of its excellent structural and performance stability under humid conditions, the CO2/N2 mixture was still well-separated on ZIF-94 with a separation time of 30.4 min when the relative humidity was as high as 99.2%, which was similar to the separation time of the dry gas experiments (33.2 min). These results pointed to the enormous potential applications of ZIF-94 for CO2/N2 separation under high humidity conditions in industrial settings.

Advances in Metal-Organic Frameworks MIL-101(Cr)

MIL-101(Cr) is one of the most well-studied chromium-based metal-organic frameworks, which consists of metal chromium ion and terephthalic acid ligand. It has an ultra-high specific surface area, large pore size, good thermal/chemical/water stability, and contains unsaturated Lewis acid sites in its structure. Due to the physicochemical properties and structural characteristics, MIL-101(Cr) has a wide range of applications in aqueous phase adsorption, gas storage and separation, and catalysis. In this review, the latest synthesis of MIL-101(Cr) and its research progress in adsorption and catalysis are reviewed.

Designing Multicomponent Metal-Organic Frameworks with Hierarchical Structure-Mimicking Distribution for High CO2 Capture Performance

By utilizing a mixed-ligand strategy, a novel multicomponent Cu-metal-organic framework (MOF) (JLU-MOF107) has been successfully synthesized. JLU-MOF107 has an unusual hierarchical structure-mimicking distribution structure. The triangular 4,4',4″-benzene-1,3,5-triyl-tribenzoate (BTB) ligand and the binuclear Cu cluster form a threefold interpenetration layer, while the linear ligand 1,4-phenylene-4,4'-bis(1,2,4-triazole) (p-tr₂ph) and tetranuclear Cu cluster form a noninterpenetration pillared-layer structure. Then, the two types of layers are connected by tetranuclear Cu clusters to construct the final sandwichlike framework. JLU-MOF107 exhibits good water and humidity stability. Due to the presence of various active sites and pores, JLU-MOF107 shows an outstanding performance for CO₂ capture (171.0 cm³ g^-1 at 273 K). Density functional theory (DFT)-based calculations further prove the interactions between CO₂ molecules and multiple active sites. The innovative synthesis of this multicomponent structure offers a new perspective on making hierarchical porous materials and multifunctional MOFs.

Multivariate metal-organic framework MTV-MIL-101 via post-synthetic cation exchange: is it truly achievable?

The post-synthetic exchange (PSE) method is a well-proven route to replace, modify, and add different functionalities to metal-organic frameworks (MOFs). Particularly, the solvent-assisted cation substitution (SACS) technique has been reported to prepare mixed-metal multivariate metal-organic frameworks (MTV-MOFs). However, such a technique does not apply to all types of MOFs. In 2013, Szilágyi et al. reported the achievement of the mixed-metal MTV-MIL-101 framework via PSE. Since then, a debate has been taking place about the validity of these findings. On the other hand, the attainment of the mixed-metal MIL-101 was reported to be obtainable through the direct synthesis, which is, to some, the only way to achieve it. Here, we settle this dispute by investigating Szilágyi's method not only as described, but also at extended conditions of time and different metal precursors: all attempts were vain. However, by reconsidering the refluxing solvent (dimethylformamide "DMF" instead of water) and the applied reaction conditions (110 °C-20 h), mixed-metal MIL-101(Cr/Fe) was achieved via a simple PSE method.

Solvent-Free Synthesis of MIL-101(Cr) for CO2 Gas Adsorption: The Effect of Metal Precursor and Molar Ratio

MIL-101(Cr), a subclass of metal–organic frameworks (MOFs), is a promising adsorbent for carbon dioxide (CO2) removal due to its large pore volume and high surface area. Solvent-free synthesis of MIL-101(Cr) was employed in this work to offer a green alternative to the current approach of synthesizing MIL-101(Cr) using a hazardous solvent. Characterization techniques including XRD, SEM, and FTIR were employed to confirm the formation of pure MIL-101(Cr) synthesized using a solvent-free method. The thermogravimetric analysis revealed that MIL-101(Cr) shows high thermal stability up to 350 °C. Among the materials synthesized, MIL-101(Cr) at the molar ratio of chromium precursor to terephthalic organic acid of 1:1 possesses the highest surface area and greatest pore volume. Its BET surface area and total pore volume are 1110 m2/g and 0.5 cm3/g, respectively. Correspondingly, its CO2 adsorption capacity at room temperature is the highest (18.8 mmol/g), suggesting it is a superior adsorbent for CO2 removal. The textural properties significantly affect the CO2 adsorption capacity, in which large pore volume and high surface area are favorable for the adsorption mechanism.

Preparation of an interpenetrating bimetal metal–organic framework via metal metathesis used for promoting gas adsorption

Novel interpenetrating bimetallic MIL-126(Cr/Sc) has been synthesized using a metal metathesis method, and showed a higher CO2, N2O and C2H2 uptake and binding energy than the parent MIL-126(Sc) material.

Recent advancement in bimetallic metal organic frameworks (M’MOFs): Synthetic challenges and applications

Metal-organic frameworks (MOFs) is a burgeoning research field and has received increasing interest in recent years due to their inherent advantages of inorganic metal ions, range of organic linkers, tunable...

Functionally modified metal–organic frameworks for the removal of toxic dyes from wastewater

This review highlights recent advancement in functional modified (FM) MOFs as superior adsorbents for the removal of dyes, classifying them by various modification strategies. The adsorption interactions affected by the FM approach are summarized.

Recent advances on bimetallic metal-organic frameworks (BMOFs): Syntheses, applications and challenges

Bimetallic metal-organic frameworks (MOFs) possess two different metal ions as nodes in their molecular frameworks. They are prepared by either using one-pot syntheses wherein different metals are mixed with suitable...

Bimetallic Ag-Zn-BTC/GO composite as highly efficient photocatalyst in the photocatalytic degradation of reactive yellow 145 dye in water

Ag_x-Zn_100-x-BTC/GO composites (BTC: benzene-1,3,5-tricarboxylic, GO: graphene oxide) with different Ag/Zn molar ratios were synthesized using microwave-assisted hydrothermal treatment. The Ag_x-Zn_100-x-BTC/GO exhibited excellent photocatalytic performance in the reactive yellow 145 dye (RY-145) degradation under irradiation of visible light with nearly 100% of RY-145 removal after 35 min, as compared to Zn-BTC/GO and Ag-BTC/GO. Reactive oxygen species scavenging assays have shown that the holes (h⁺) and superoxide radical anion (O₂^-•) play a primary role in RY-145 degradation. Based on the band structure of materials, the Z-scheme photocatalytic mechanism was suggested. The effect of catalyst dosage, pH and dye concentration on the efficiency of photocatalytic activity of bimetallic Ag₅₀-Zn₅₀-BTC/GO was also investigated. The improvement in photocatalytic activity of bimetallic Ag₅₀-Zn₅₀-BTC/GO could be given by the synergism of (i) absorption of visible light confirmed by UV-Vis diffuse reflectance spectra; (ii) the increased lifetime as evidenced by photoluminescence spectra and transient photocurrent response; (iii) the increased oxygen vacancy defects as confirmed by X-ray photoelectron spectroscopy results. The degradation pathway of RY-145 dye was also predicted based on liquid chromatography-mass spectrometer analysis. The removed chemical oxygen demand, biological oxygen demand, total organic carbon outcomes indicated the high mineralization ability for RY-145 degradation over Ag₅₀-Zn₅₀-BTC/GO.

Advances in Post-Combustion CO2 Capture by Physical Adsorption: From Materials Innovation to Separation Practice

The atmospheric CO₂ concentration continues a rapid increase to its current record high value of 416 ppm for the time being. It calls for advanced CO₂ capture technologies. One of the attractive technologies is physical adsorption-based separation, which shows easy regeneration and high cycle stability, and thus reduced energy penalties and cost. The extensive research on this topic is evidenced by the growing body of scientific and technical literature. The progress spans from the innovation of novel porous adsorbents to practical separation practices. Major CO₂ capture materials include the most widely used industrially relevant porous carbons, zeolites, activated alumina, mesoporous silica, and the newly emerging metal-organic frameworks (MOFs) and covalent-organic framework (COFs). The key intrinsic properties such as pore structure, surface chemistry, preferable adsorption sites, and other structural features that would affect CO₂ capture capacity, selectivity, and recyclability are first discussed. The industrial relevant variables such as particle size of adsorbents, the mechanical strength, adsorption heat management, and other technological advances are equally important, even more crucial when scaling up from bench and pilot-scale to demonstration and commercial scale. Therefore, we aim to bring a full picture of the adsorption-based CO₂ separation technologies, from adsorbent design, intrinsic property evaluation to performance assessment not only under ideal equilibrium conditions but also in realistic pressure swing adsorption processes.

Metal-Organic Frameworks: Synthetic Methods and Potential Applications

Metal-organic frameworks represent a porous class of materials that are build up from metal ions or oligonuclear metallic complexes and organic ligands. They can be considered as sub-class of coordination polymers and can be extended into one-dimension, two-dimensions, and three-dimensions. Depending on the size of the pores, MOFs are divided into nanoporous, mesoporous, and macroporous items. The latter two are usually amorphous. MOFs display high porosity, a large specific surface area, and high thermal stability due to the presence of coordination bonds. The pores can incorporate neutral molecules, such as solvent molecules, anions, and cations, depending on the overall charge of the MOF, gas molecules, and biomolecules. The structural diversity of the framework and the multifunctionality of the pores render this class of materials as candidates for a plethora of environmental and biomedical applications and also as catalysts, sensors, piezo/ferroelectric, thermoelectric, and magnetic materials. In the present review, the synthetic methods reported in the literature for preparing MOFs and their derived materials, and their potential applications in environment, energy, and biomedicine are discussed.

Role of Lewis Acids of MIL-101(Cr) in the Upgrading of Ethanol to n-Butanol

The upgrading of bioethanol to n-butanol has recently been a focus of considerable attention due to the advantages of n-butanol over bioethanol as a sustainable fuel. The efficiency of this reaction is highly dependent on the development of catalysts, where understanding how catalysts perform is essential. However, traditional catalysts are normally composed of several kinds of active sites that work together synergistically in reactions, making it challenging to identify the role that individual active sites play. Herein, we synthesized three chromium-based MOFs ((MIL-101(Cr), where MIL stands for Matériaux Institut Lavoisier) with different Lewis acidities but without any basic sites. The linear relationship between Lewis acidities and their dehydration and condensation abilities suggests that there is a competition between the ethanol dehydration to diethyl ether and acetaldehyde condensation on Lewis acids. Upon the introduction of Pd, the Lewis acidity also dominates the particle size of Pd and then the dehydrogenation and hydrogenating abilities of catalysts.

In situ casting of rice husk ash in metal organic frameworks induces enhanced CO2 capture performance

Incorporation of rice-husk-ash (RHA), an agricultural waste, in situ during the synthesis of MIL-101(Cr) resulted in a significant improvement in the CO2 adsorption properties over the synthesized RHA-MIL-101(Cr). The newly synthesized RHA-MIL-101(Cr) composite exhibited an enhancement of 14-27% in CO2 adsorption capacity as compared to MIL-101(Cr) at 25 °C and 1 bar. The content of RHA incorporated in RHA-MIL-101(Cr) fine tuned the CO2 capture performance to achieve high working capacity (0.54 mmol g-1), high purity (78%), superior CO2/N2 selectivity (18) and low isosteric heat of adsorption (20-30 kJ mol-1). The observed superior CO2 adsorption performance of RHA-MIL-101(Cr) is attributed to the fine tuning of textural characteristics-enhancement of 12-27% in BET surface area, 12-33% in total pore volume and 18-30% in micropore volume-upon incorporation of RHA in MIL-101(Cr).

Enhancing Selective Adsorption in a Robust Pillared-Layer Metal-Organic Framework via Channel Methylation for the Recovery of C2-C3 from Natural Gas

Here, we reported a strategy for channel methylation to construct a robust ultramicroporous metal-organic framework (MOF) Ni(TMBDC)(DABCO)_0.5 through hydrothermal synthesis method and investigated its adsorption performance for recovering ethane (C₂) and propane (C₃) from natural gas. The as-synthesized Ni(TMBDC)(DABCO)_0.5 featured ultramicroporosity with a uniform pore size of 0.5 nm. The resulting sample showed a strong adsorption interaction with C₃H₈ and C₂H₆, and its C₃H₈ adsorption capacity at a low pressure of 1 kPa was up to 2.80 mmol/g and its C₂H₆ adsorption capacity at a low pressure of 10 kPa reached as high as 2.93 mmol/g, exhibiting strong binding affinity for ethane and propane. The enhanced adsorption can be attributed to the presence of the dense and accessible methyl and methylene groups in the channels of the sample. Grand Canonical Monte Carlo (GCMC) simulations also confirmed that the methylene groups from the DABCO pillar and the methyl groups from the TMBDC ligand play an important role in enhancing the adsorption of ethane and propane. Its ideal adsorbed solution theory (IAST)-predicted selectivity of C₂H₆/CH₄ reached unprecedentedly 29, much higher than most of the reported data for MOFs. The stability test confirmed that the crystal structure of Ni(TMBDC)(DABCO)_0.5 still remained intact after it was exposed to moist air with a relative humidity of 100% for days. The breakthrough experiment demonstrated that the CH₄/C₂H₆/C₃H₈ ternary mixture was completely separated using a fixed bed of Ni(TMBDC)(DABCO)_0.5 at ambient temperature, showing a great potential for recovering the low content of ethane and propane from natural gas.