Hazardous contaminants in plastics contained in compost and agricultural soil

Phthalates and other organic chemicals in agricultural soils after use of different types of conventional and biodegradable plastics

Various plastic materials are used in contact with agricultural soil, like mulching films, crop covers, weed controlling fabrics and nets. Polyethylene (PE) mulches have already been recognized as a significant source of plastic in soil and they have been shown to contain additives like phthalates, known as endocrine disruptors. However, other agricultural plastics are less studied, and little is known on the substances potentially released from them endangering biodiversity and the human health. This research aims to assess whether different agricultural plastics release additives into soil and to compare the release among various materials. We collected soil samples from 38 agricultural fields where conventional mulching films (PE), weed controlling fabrics (PP), biodegradable mulches based on polybutylene adipate terephthalate (PBAT), frost covers (PP), and oxo-degradable films (at least OXO-PE) were used. We analyzed the soils for phthalates and acetyl tributyl citrate (ATBC), used as plastic additives, and for polycyclic aromatic hydrocarbons (PAH) and dodecane that have high affinity for plastics. In comparison to the control soils, dibutylphthalate (DBP) and ATBC concentrations were significantly higher in soils mulched with PE and, partly, with biodegradable films. DBP concentration found in soil samples ranged between below the limit of quantification at a control site (1.5 μg kg-1) to 135 μg kg-1 at a site mulched with OXO-PE. The highest ATBC concentration, 22 ± 6 μg kg-1, was registered in a site mulched with PE, showing a statistically significant difference not only in comparison to the controls but also when compared to sites mulched with OXO-PE (p = 0.029) and PBAT (p < 0.009). On the contrary, the use of agricultural plastics did not influence the concentration of PAHs and dodecane. Our results indicate that agricultural plastics are a source of some organic chemicals to agricultural soils, including phthalates that are known for posing threat to soil ecosystem and human health.

Quantification and polymeric characterization of microplastics in composts and their accumulation in lettuce

Organic fertilizers have become a vector for the transport of microplastics (MPs), which pose human health concerns through the food chain. This study aimed to quantify and characterize MPs in eight different compost samples of various raw materials and their subsequent translocation to lettuce (Lacuta sativa) grown on contaminated composts. The results revealed that the MP abundance ranged from 3810 to 16530 MP/kg. Municipal solid waste compost (MSWC) had highest abundance (16082 ± 632 MP/kg), followed by leaf compost (LC) and organic compost (OC) (6299 ± 1011 and 3680 ± 419 MP/kg, respectively). MPs of <100 μm in size were most dominant in MSWC and LC. Fragments and fibers were the prevalent shape types, with white/transparent colored MPs being more abundant. Polyethylene (PE), polypropylene (PP) and polyethylene terephthalate (PET) were the dominant polymers. MPs accumulation in the lettuce leaves was greatest in the lettuce plants grown on MSWC, followed by those grown on LC and OC, indicating that MSWC grown lettuce is not suitable for human consumption. The decrease in the growth (leaf length, number of leaves, leaf fresh and weights) and physiological (membrane stability index, relative water contents) parameters of lettuce was in line with the trend of MP accumulations. Hence, it is highly important to regulate the plastic contents in compost because it is a threat to ecosystems and human health.

Nano(micro)plastic mobility in soil: Metallic additives and Sr isotopes as potential tracers

Metal contaminants were found in a soil amended with a compost produced from household waste that included plastic debris. A strong correlation between the microplastics (MPs) distribution and the metal concentrations in the soil profile. Metals in the highest concentrations corresponded to the most significant plastic additives. As the total amount of plastic debris and the loss of metals and plastic particles were unknown, it was not possible to conclude that plastic debris is responsible for all of the metal contamination. Amount of calcium (Ca) in MPs (24.5 g kg-1 of MPs) are high in response to it use as filler in plastic formulation. As strontium (Sr) is an analogous of Ca, the potential of 87Sr/86Sr ratios to quantify MPs and nanoplastics (NPs) was tested. Elemental concentrations (Ca, Cd, Cr Pb, Ni and Sr) coupled with Sr isotopic ratios were compared in both amended soil and a reference soil without amendment. The 87Sr/86Sr ratios of the amended soil were less radiogenic than for the reference soil (0.724296 ± 0.000010 against 0.726610 ± 0.00009 for the 0-5 cm soil layer, respectively). The Sr isotopic ratio of MPs was also significantly less radiogenic (0.711527 ± 0.000010 for the 0-5 cm soil layer) than for soils. The MPs< 2 mm occurred in the ploughed soil depth with concentration varying from 1.19 to 0.09 mg kg-1. The NPs concentration stayed quite constant from 0 to 55 cm at around 0.25 µg kg-1. The presence of NPs until 55 cm soil depth was attested by the detection of polypropylene NPs by Py-GCMS in the soil solution < 0.8 µm. These results highlighted, for the first time, the NPs mobility throughout the soil depth and their ability to reach hydrosystems. It also demonstrated that Sr could be a potential tracer of the MPs< 2 mm and NPs amount occurring in soils.

Plastic particles in urban compost and their grain size distribution

Gathering information on plastic particles in composts and the processes they undergo is important in terms of potentially limiting their further entry into the environment, for example, in improving the fertilising properties of soils. Microplastics (MPs) were determined in composts produced from urban greenery. They are present in decreasing order: polyethylene terephthalate, polystyrene, polyethylene, and polypropylene. The determination of polymers and additives used to improve their properties was performed by pyrolysis and gas chromatography with mass spectrometric detection (Py-GC/MS). Additives and microplastics are most concentrated in composts in the 0.315-0.63 and 0.63-1.25 mm grain size class, together with the carbon contained in the compost dry matter. Additives form 0.11-0.13% of MPs in dry matter of compost. The average concentration of microplastics in the particle size class from 0.63 to 1.25 mm is 2434 ± 224 mg/kg; in the total sample of composts, it is 1368 ± 286 mg/kg of P-MPs. For composts with particle size <2.5 mm, a relationship between the C/N ratio and the plastic particle concentration was statistically significant. It documents a similar behaviour of lignocellulose and plastic particles during the degradation processes. A relationship between the concentration of polymer markers and additives in the compost dry matter and their concentrations in the leachate has been demonstrated. The leachability from compost is higher for additives than for chemical compounds originating from the decomposition of the main components of MPs. The suitability of the use of the compost for agricultural purposes was monitored by the germination index (GI) for watercress. The lowest value of the GI was determined in the particle size class from 0.63 to 1.25 mm. The leachability of polymer markers and additives alone cannot explain the low GI value in this grain size class. The GI value is also influenced by the leachability of chemical compounds characterised by the value of dissolved organic carbon (DOC) and water-leachable nitrogen (Nw). A statistically significant dependence between DOC/Nw and the germination index value was found.

A bibliometric perspective on the occurrence and migration of microplastics in soils amended with sewage sludge

The land application of sewage sludge from wastewater treatment plants has been recognized as a major source of microplastic contamination in soil. Nevertheless, the fate and behavior of microplastics in soil remain uncertain, particularly their distribution and transport, which are poorly understood. This study does a bibliometric analysis and visualization of relevant research publications using the CiteSpace software. It explores the limited research available on the topic, highlighting the potential for it to emerge as a research hotspot in the future. Chinese researchers and institutions are paying great attention to this field and are promoting close academic cooperation among international organizations. Current research hot topics mainly involve microplastic pollution caused by the land application of sewage sludge, as well as the detection, environmental fate, and removal of microplastics in soil. The presence of microplastics in sludge, typically ranging from tens of thousands to hundreds of thousands of particles (p)/kg, inevitably leads to their introduction into soil upon land application. In China, the estimated annual accumulation of microplastics in the soil due to sludge use is approximately 1.7 × 1013 p. In European countries, the accumulation ranges from 8.6 to 71 × 1013 p. Sludge application has significantly elevated soil microplastic concentrations, with higher application rates and frequencies resulting in up to several-fold increases. The primary forms of microplastics found in soils treated with sludge are fragments and fibers, primarily in white color. These microplastics consist primarily of components such as polyamide, polyethylene, and polypropylene. The vertical transport behavior of microplastics is influenced by factors such as tillage, wind, rainfall, bioturbation, microplastic characteristics (e.g., fraction, particle size, and shape), and soil physicochemical properties (e.g., organic matter, porosity, electrical conductivity, and pH). Research indicates that microplastics can penetrate up to 90 cm into the soil profile and persist for decades. Microplastics in sewage sludge-amended soils pose potential long-term threats to soil ecosystems and even human health. Future research should focus on expanding the theoretical understanding of microplastic behavior in these soils, enabling the development of comprehensive risk assessments and informed decision-making for sludge management practices. PRACTITIONER POINTS: Microplastics in sewage sludge range from tens to hundreds of thousands per kilogram. Sludge land application contributes significantly to soil microplastic pollution. The main forms of microplastics in sludge-amended soils are fragments and fibers. Microplastics are mainly composed of polyamide, polyethylene, and polypropylene. Microplastics can penetrate up to 90 cm into the soil profile and persist for decades.

PFAS occurrence and distribution in yard waste compost indicate potential volatile loss, downward migration, and transformation

We discovered high concentrations of PFAS (18.53 ± 1.5 μg kg-1) in yard waste compost, a compost type widely acceptable to the public. Seventeen out of forty targeted PFAS, belonging to six PFAS classes were detected in yard waste compost, with PFCAs (13.51 ± 0.99 μg kg-1) and PFSAs (4.13 ± 0.19 μg kg-1) being the dominant classes, comprising approximately 72.5% and 22.1% of the total measured PFAS. Both short-chain PFAS, such as PFBA, PFHxA, and PFBS, and long-chain PFAS, such as PFOA and PFOS, were prevalent in all the tested yard waste compost samples. We also discovered the co-occurrence of PFAS with low-density polyethylene (LDPE) and polyethylene terephthalate (PET) plastics. Total PFAS concentrations in LDPE and PET separated from incoming yard waste were 7.41 ± 0.41 μg kg-1 and 1.35 ± 0.1 μg kg-1, which increased to 8.66 ± 0.81 μg kg-1 in LDPE and 5.44 ± 0.56 μg kg-1 in PET separated from compost. An idle mature compost pile revealed a clear vertical distribution of PFAS, with the total PFAS concentrations at the surface level approximately 58.9-63.2% lower than the 2 ft level. This difference might be attributed to the volatile loss of short-chain PFCAs, PFAS's downward movement with moisture, and aerobic transformations of precursor PFAS at the surface.

Exposure assessment of plastics, phthalate plasticizers and their transformation products in diverse bio-based fertilizers

Bio-based fertilizers (BBFs) produced from organic waste have the potential to reduce societal dependence on limited and energy-intensive mineral fertilizers. BBFs, thereby, contribute to a circular economy for fertilizers. However, BBFs can contain plastic fragments and hazardous additives such as phthalate plasticizers, which could constitute a risk for agricultural soils and the environment. This study assessed the exposure associated with plastic and phthalates in BBFs from three types of organic wastes: agricultural and food industry waste (AgriFoodInduWaste), sewage sludge (SewSludge), and biowaste (i.e., garden, park, food and kitchen waste). The wastes were associated with various treatments like drying, anaerobic digestion, and vermicomposting. The number of microplastics (0.045-5 mm) increased from AgriFoodInduWaste-BBFs (15-258 particles g-1), to SewSludge-BBFs (59-1456 particles g-1) and then to Biowaste-BBFs (828-2912 particles g-1). Biowaste-BBFs mostly contained packaging plastics (e.g., polyethylene terephthalate), with the mass of plastic (>10 g kg-1) exceeding the EU threshold (3 g kg-1, plastics >2 mm). Other BBFs mostly contained small (< 1 mm) non-packaging plastics in amounts below the EU limit. The calculated numbers of microplastics entering agricultural soils via BBF application was high (107-1010 microplastics ha-1y-1), but the mass of plastic released from AgriFoodInduWaste-BBFs and SewSludge-BBFs was limited (< 1 and <7 kg ha-1y-1) compared to Biowaste-BBFs (95-156 kg ha-1y-1). The concentrations of di(2-ethylhexyl)phthalate (DEHP; < 2.5 mg kg-1) and phthalate transformation products (< 8 mg kg-1) were low (< benchmark of 50 mg kg-1 for DEHP), attributable to both the current phase-out of DEHP as well as phthalate degradation during waste treatment. The Biowaste-BBF exposed to vermicomposting indicated that worms accumulated phthalate transformation products (4 mg kg-1). These results are overall positive for the implementation of the studied AgriFoodInduWaste-BBFs and SewSludge-BBFs. However, the safe use of the studied Biowaste-BBFs requires reducing plastic use and improving sorting methods to minimize plastic contamination, in order to protect agricultural soils and reduce the environmental impact of Biowaste-BBFs.

Are microplastics in livestock and poultry manure an emerging threat to agricultural soil safety?

Microplastics (MPs) have attracted much attention in recent years, due to the difficulty of degradation and threats to ecological systems and humans. Based on the analysis of 1429 articles on MPs in soil, we found that we know little about the behavior and fate of manure-born MPs from the livestock and poultry production systems to agriculture soils. This review summarizes the analytical methods for sampling, separation, and identification and the occurrence of MPs in livestock and poultry manure, mainly based on 7 surveys related to manure-born MPs. Then, the sources, fate, and environmental risks of MPs in livestock and poultry manure are discussed. MPs, heavy metals, pathogens, antibiotic resistance genes, and persistent organic pollutants are common pollutants in livestock and poultry manure. Worse, manure-born MPs will become smaller, rougher, and more numerous and could easily form more toxic compound pollution after complicated processes of manure treatment, which seriously threatens agricultural soil safety. Finally, an outlook is offered for future research. We hope this article to attract attention to the risks of MPs in livestock and poultry manure and provide a reference for future research.

Unraveling impacts of inoculating novel microbial agents on nitrogen conversion during cattle manure composting: Core microorganisms and functional genes

The impacts of microbial agents on nitrogen conversion during composting is still not entirely clear. In this research, a novel microbial agent containing two thermotolerant nitrifying bacteria was identified and its impacts on nitrogen conversion, bacterial structure and functional genes during cattle manure composting were investigated. The results revealed that the inoculation enhancing the maturation of compost, increased the total nitrogen by 13.6-26.8%, reduced NH3 emission and the N2O emission by 24.8-36.1% and 22.7-32.1%, respectively. Particularly, the microbial agents mixed Acinetobacter radioresistens and Bacillus nitratireducens (1:1, treatment group 1) had the best nitrogen preservation effect. Furthermore, the inoculation not only produced diverse diazotroph community but could strength the co-occurrence between core microorganisms to promote nitrogen metabolism. The metagenomic analysis demonstrated that the inoculation decreased the abundance of nitrate reduction gene (nirS, norC, nap and nif), and increased the abundance of hao, thus facilitating nitrification and suppressing NH3 and N2O emission.

Analysis of micro- and nanoplastics in wastewater treatment plants: key steps and environmental risk considerations

The analysis of micro- and nanoplastics (MNPs) in the environment is a critical objective due to their ubiquitous presence in natural habitats, as well as their occurrence in various food, beverage, and organism matrices. MNPs pose significant concerns due to their direct toxicological effects and their potential to serve as carriers for hazardous organic/inorganic contaminants and pathogens, thereby posing risks to both human health and ecosystem integrity. Understanding the fate of MNPs within wastewater treatment plants (WWTPs) holds paramount importance, as these facilities can be significant sources of MNP emissions. Additionally, during wastewater purification processes, MNPs can accumulate contaminants and pathogens, potentially transferring them into receiving water bodies. Hence, establishing a robust analytical framework encompassing sampling, extraction, and instrumental analysis is indispensable for monitoring MNP pollution and assessing associated risks. This comprehensive review critically evaluates the strengths and limitations of commonly employed methods for studying MNPs in wastewater, sludge, and analogous environmental samples. Furthermore, this paper proposes potential solutions to address identified methodological shortcomings. Lastly, a dedicated section investigates the association of plastic particles with chemicals and pathogens, alongside the analytical techniques employed to study such interactions. The insights generated from this work can be valuable reference material for both the scientific research community and environmental monitoring and management authorities.

Ecotoxicity of micro- and nanoplastics on aquatic algae: Facts, challenges, and future opportunities

The production of plastic has exponentially increased in recent years, leading to the release of millions of tons of plastic waste into the environment annually. This waste can break down into smaller micro- and nanoplastics (MNPs) that are toxic and reactive to life forms, including humans. MNPs are particularly concerning for marine biologists and environmental scientists due to their toxic impacts on aquatic organisms, including algae, which are the foundation of the food chain. The review provides a comprehensive overview of the (eco)toxicity assessment of MNPs on aquatic algal communities, highlighting the novel insights gained into the ecotoxicity of various MNPs on algae and the associated health risks for aquatic ecosystems, food chains, and humans. This article also discusses current challenges and future research opportunities to address these challenges, making it a valuable contribution to the field of environmental science. Overall, this work is one of the first efforts to comprehensively assess the effects of MNPs on aquatic algae, emphasizing the significant risks that MNPs pose to essential ecosystems and human health.

Incomplete degradation of aromatic-aliphatic copolymer leads to proliferation of microplastics and antibiotic resistance genes

Biodegradable plastics (BDPs) have attracted extensive attention as an alternative to conventional plastics. BDPs could be mineralized by composting, while the quality of compost affected by the presence of BDPs and the residual microplastics (MPs) has not been well evaluated. This study aimed to explore the MPs release potential and environmental implications of commercial BDPs (aromatic-aliphatic copolymer) films in uncontrolled composting. Results showed that the molecular weight of BDPs decreased by >60% within 60 d. However, the non-extracted organic matter and wet-sieving measurements indicated that MPs continuously released and accumulated during regular composting. The average MPs release potential (0.1-5 mm) was 134.6 ± 18.1 particles/mg (BDPs), which resulted in 103-104 particles/g dw in compost. The plastisphere of MPs showed a significantly higher (0.95-16.76 times) abundance of antibiotic resistance genes (ARGs), which resulted in the rising (1.34-2.24 times) of ARGs in compost heaps, in comparison to the control groups. Overall, BDPs promote the spread of ARGs through the selective enrichment of bacteria and horizontal transfer from released MPs. These findings confirmed that BDPs could enhance the release potential of MPs and the dissemination of ARGs, which would promote the holistic understanding and environmental risk of BDPs.

Removal of organic and inorganic contaminants from the air, soil, and water by algae

Rapid increases in human populations and development has led to a significant exploitation of natural resources around the world. On the other hand, humans have come to terms with the consequences of their past mistakes and started to address current and future resource utilization challenges. Today's primary challenge is figuring out and implementing eco-friendly, inexpensive, and innovative solutions for conservation issues such as environmental pollution, carbon neutrality, and manufacturing effluent/wastewater treatment, along with xenobiotic contamination of the natural ecosystem. One of the most promising approaches to reduce the environmental contamination load is the utilization of algae for bioremediation. Owing to their significant biosorption capacity to deactivate hazardous chemicals, macro-/microalgae are among the primary microorganisms that can be utilized for phytoremediation as a safe method for curtailing environmental pollution. In recent years, the use of algae to overcome environmental problems has advanced technologically, such as through synthetic biology and high-throughput phenomics, which is increasing the likelihood of attaining sustainability. As the research progresses, there is a promise for a greener future and the preservation of healthy ecosystems by using algae. They might act as a valuable tool in creating new products.

Comparative toxicity of conventional versus compostable plastic consumer products: An in-vitro assessment

This study investigates the toxicity of methanolic extracts obtained from compostable plastics (BPs) and conventional plastics (both virgin and recycled). Additionally, it explores the potential influence of plastic photodegradation and composting on toxic responses using a battery of in vitro assays conducted in PLHC-1 cells. The extracts of BPs, but not those of conventional plastics, induced a significant decrease in cell viability (<70%) in PLHC-1 cells after 24 h of exposure. Toxicity was enhanced by either photodegradation or composting of BPs. Extracts of conventional plastics, and particularly those of recycled plastics, induced 7-ethoxyresorufin-O-deethylase (EROD) activity and micronucleus formation in exposed cells, indicating the presence of significant amounts of CYP1A inducers and genotoxic compounds in the extracts, which was enhanced by photodegradation. These findings highlight the importance of investigating the effects of degradation mechanisms such as sunlight and composting on the toxicity of BPs. It is also crucial to investigate the composition of newly developed formulations for BPs, as they may be more harmful than conventional ones.

Organic composts as A vehicle for the entry of microplastics into the environment: A comprehensive review

Plastic pollution is a widespread issue that poses a threat to agroecosystems. Recent data on microplastic (MP) pollution from compost and its application to soil have highlighted the potential impact of micropollutants that may be transferred from compost. Thus, we aim with this review to elucidate the distribution-occurrence, characterization, fate/transport, and potential risk of MPs from organic compost to gain comprehensive knowledge and mitigate the adverse impacts of compost application. The concentration of MPs in compost was up to thousands of items/kg. Among micropollutants, fibers, fragments, and films are the most common, with small MPs having a higher potential to absorb other pollutants and cause harm to organisms. Various synthetic polymers, including polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), polystyrene (PS), polyvinyl chloride (PVC), polyester (PES), and acrylic polymers (AP), have been widely used of plastic items. MPs are emerging pollutants that can have diverse effects on soil ecosystems, as they can transfer potential pollutants from MPs to compost and then to the soil. Following the microbial degradation scheme, the transfer chain from plastics to compost to soil can be broken down into main stages, i.e., colonization - (bio)fragmentation - assimilation - and mineralization. Microorganisms and adding biochar play an essential role during composting, which can be an effective solution to enhance MP degradation. Findings have shown that stimulating free radical generation could promote the biodegradation efficacy of MPs and possibly remove their occurrence in compost, thereby reducing their contribution to ecosystem pollution. Furthermore, future recommendations were discussed to reduce ecosystem risks and health challenges.

A Review of Biodegradable Plastics: Chemistry, Applications, Properties, and Future Research Needs

Environmental concerns over waste plastics' effect on the environment are leading to the creation of biodegradable plastics. Biodegradable plastics may serve as a promising approach to manage the issue of environmental accumulation of plastic waste in the ocean and soil. Biodegradable plastics are the type of polymers that can be degraded by microorganisms into small molecules (e.g., H2O, CO2, and CH4). However, there are misconceptions surrounding biodegradable plastics. For example, the term "biodegradable" on product labeling can be misconstrued by the public to imply that the product will degrade under any environmental conditions. Such misleading information leads to consumer encouragement of excessive consumption of certain goods and increased littering of products labeled as "biodegradable". This review not only provides a comprehensive overview of the state-of-the-art biodegradable plastics but also clarifies the definitions and various terms associated with biodegradable plastics, including oxo-degradable plastics, enzyme-mediated plastics, and biodegradation agents. Analytical techniques and standard test methods to evaluate the biodegradability of polymeric materials in alignment with international standards are summarized. The review summarizes the properties and industrial applications of previously developed biodegradable plastics and then discusses how biomass-derived monomers can create new types of biodegradable polymers by utilizing their unique chemical properties from oxygen-containing functional groups. The terminology and methodologies covered in the paper provide a perspective on directions for the design of new biodegradable polymers that possess not only advanced performance for practical applications but also environmental benefits.

Microplastics in soils during the COVID-19 pandemic: Sources, migration and transformations, and remediation technologies

The COVID-19 pandemic has led to a notable upsurge of 5-10 % in global plastic production, which could have potential implications on the soil quality through increased microplastics (MPs) content. The elevated levels of MPs in the soil poses a significant threat to both the environment and human health, hence necessitating the remediation of MPs in the environment. Despite the significant attention given to MPs remediation in aqueous environments, less consideration has been given to MPs remediation in the soil. Consequently, this review highlights the major sources of MPs in the soil, their migration and transformation behaviors during the COVID-19 pandemic, and emphasizes the importance of utilizing remediation technologies such as phytoremediation, thermal treatment, microbial degradation, and photodegradation for MPs in the soil. Furthermore, this review provides a prospective outlook on potential future remediation methods for MPs in the soil. Although the COVID-19 pandemic is nearing its end, the long-term impact of MPs on the soil remains, making this review a valuable reference for the remediation of MPs in the post-pandemic soil.

Thermal desorption mechanism of n-dodecane on unsaturated clay: Experimental study and molecular dynamics simulation

Thermal desorption technology can effectively remediate fuels-contaminated clayey soil. However, the microscopic mechanism for the contaminant desorption on clay is still unclear, especially with the existence of water on clay surfaces. In this study, a combination method including TGA experiments, multi-phase and multi-component kinetic models, and MD simulation was proposed to reveal the thermal desorption mechanism of n-dodecane in unsaturated clay. Results showed that the thermal desorption behavior of the free nonaqueous phase liquid (NAPL) and the adsorbed phase of n-dodecane or water could be identified by the multi-phase and multi-component kinetic models based on the desorption process rate obtained by thermogravimetric analysis (TGA) experiments. The activation energy of the NAPL phase (49-69.9 kJ/mol) was lower than the adsorbed phase (90 kJ/mol). The activation energy of the NAPL phase had the same linear relationship with its mass on kaolinite and montmorillonite, while adsorbed phase only existed on the kaolinite surface. MD simulation showed that water demonstrated competitive adsorption with n-dodecane on montmorillonite surfaces and prevented the formation of the adsorbed phase while having little influence on the n-dodecane adsorption on kaolinite surface, which agrees well with the kinetic analysis of the TGA experiments. With the combination of macroscopic experimental analysis and microscopic molecular simulation, it can be concluded that the mass of the NAPL phase limited the desorption behavior, while the interaction between the clay mineral surface and n-dodecane was the key factor that dominated the thermal desorption behavior of the adsorbed phase. The presented results provide new insight into the desorption mechanism of hydrocarbon on clay minerals, which is of significance for the design of thermal desorption remediation.

Microplastics as an underestimated emerging contaminant in solid organic waste and their biological products: Occurrence, fate and ecological risks

Microplastics (MPs), as an emerging pollutant, have been widely detected in aquatic, terrestrial, and atmospheric ecosystems. Recently, more researchers indicated that solid organic waste is also a crucial repository of MPs and has become a vital pollution source in ecosystems. Although the occurrence and fate of MPs in solid organic waste and the interaction between MPs and biological treatments have been explored, there still needs to be comprehensive summaries. Hence, this study reviewed the occurrence and characteristics of MPs in solid organic waste and organic fertilizers. Meanwhile, this study summarized the influence of MPs on biological treatments (composting and anaerobic digestion) and their degradation characteristics. MPs are abundant in solid organic waste (0-220 ×10³ particles/kg) and organic fertilizer (0-30 ×10³ particles/kg), PP and PE are the prominent MPs, and fibers and fragments are the main shapes. MPs can affect the carbon and nitrogen conversion during biological treatments and interfere with microbial communities. The MP's characteristics changed after biological treatments, which should further consider their potential ecological risks. This review points out the existing problems of MPs in organic waste recycling and provides directions for their treatment in the future.

A novel approach to extract, purify, and fractionate microplastics from environmental matrices by isopycnic ultracentrifugation

The increasing accumulation of microplastics (MP) in the environment is considered one of the most important environmental challenges of our times. Reliable extraction and detection methods for MP in environmental samples are essential for determining the extent of pollution and assessing ecological risks. However, extraction of MP from complex environmental matrices such as soil remains technically challenging. Today, density-based extractions with saturated salt solutions are widely applied. Nevertheless, current methods do not allow for the fractionation of different MP particle types according to their specific polymer densities. Here, we present a novel isopycnic ultracentrifugation approach for the simultaneous extraction and fractionation of MP mixtures based on the particle-specific buoyant densities. In this proof-of-concept study, diffusion-based density gradients were prepared using caesium chloride media, covering a density range between 1.1 and 1.5 g mL^-1_, sufficient to resolve many common polymer densities. We selected MP particles with a low (polyamide; PA66), medium (polybutylene adipate terephthalate; PBAT), and high (polyethylene terephthalate; PET) density to validate separation performance. Both pristine and soil-incubated MP mixtures showed clear banding patterns at expected buoyant densities after isopycnic separation. μFTIR imaging of subsamples collected from resolved MP fractions showed a polymer-specific separation of ≥87.6 %. In addition, the quantitative recovery of MP particles from soil was between 86 and 99 %. The potential of isopycnic ultracentrifugation to preserve MP-associated biofilms was also assessed. Soil-incubated MP particles were inspected by confocal laser scanning microscopy before and after isopycnic separation, indicating a preservation of bioorganic structures. Hence, isopycnic ultracentrifugation offers a powerful novel approach for a polymer-specific extraction and resolution of MP particles with a wide potential for applications in MP research.

Microplastics (MPs) distribution in Surface Sediments of the Freidounkenar Paddy Wetland

There is an urgent need to increase knowledge on the distribution of microplastics (MPs) in wetlands because these are sites of special ecological value and the ever-growing use of plastic can threaten such fragile ecosystems. This research assesses, for the first time, the occurrence of MPs in surface sediment of the Freidounkenar International Wetland (Northern Iran), a valuable habitat for migratory birds. A total of 1368 MP/kg were identified in the surface sediments of the wetland. The distribution of MPs in sediments per area was Ezbaran (36.5%), Western Sorkhrood (32.0%), Freidounkenar (20.1%) and Eastern Sorkhrood Ab-bandans (11.4%). The most contaminated sites were located close to agricultural fields, Damgahs (agroecosystems for birds), fishing areas and roads. Fibers and white-transparent and black-grey MPs constituted the dominant MPs in the surface sediment. The most abundant MPs were < 250 μm and these were made of nylon, polypropylene-low density polyethylene copolymer, polystyrene, low density polyethylene and polypropylene. The identification of MPs was carried out visually and supported with Scanning Electron Microscopy (SEM)-Energy Dispersive X-Ray (EDX) and micro-Raman techniques. There were weathering signs in large proportion of the MPs, according to SEM analysis, which evidences their formation from the degradation of other plastics. This is a comprehensive study on MPs in surface sediment of this sensitive internationally recognized ecosystem with high ecological value.

Leaching of di-2-ethylhexyl phthalate from biodegradable and conventional microplastics and the potential risks

There has been a growing concern about plastic pollution, both from a health and ecological perspective. One of the major concerns with plastic debris, especially microplastics (MPs) relates to their strong potential for releasing additives and chemicals. Di-2-ethylhexyl phthalate (DEHP) is a common plastic additive widely used as plasticizer in plastic products, and is of global concern due to its widespread contamination in the environment. In this study, two conventional nondegradable plastics (polyethylene (PE) bags and PE mulch) and two biodegradable plastics (poly(butylene adipate co-terephtalate)-starch-based-polylactic acid bags (PBAT/PLA bags) and PLA mulch) were selected to investigate the release of DEHP to seawater. The results showed that leaching potentials of DEHP from different types of MPs varied. Among the four selected MPs, PE mulch had the highest leaching potential (6.88 μg/g), followed by PE bags (4.24 μg/g), PLA mulch (1.10 μg/g) and PBAT/PLA bags (0.89 μg/g). The DEHP leaching kinetic curves of the four MPs were all in line with the pseudo first order model. The potential risk of environmental and human exposure to the leached DEHP was assessed using the average Phthalate Pollution Index (PPI). The calculated PPI indicated low pollution risks of DEHP released by the four MPs in seawater.

Characterization of microplastics in the septic tank via laser direct infrared spectroscopy

Microplastics (MPs) are emerging pollutants that have been widely detected in the atmosphere, hydrosphere, lithosphere, and biosphere. Such wide spread of MPs indicates that the effective control in different environmental sectors is in an urgent need, and the first step in meeting this need is to identify the occurrence of MPs in the relevant environment. However, research on MPs in septic tanks has not been reported so far. This study investigated the distribution characteristics of MPs in septic tanks with a size detection limit of as low as 20 μm detected by laser direct infrared spectroscopy. Results showed that the number of MPs in the septic tank was reached 2803 (1489-4816) particles/g dry sludge, and the amount detected in the sediments was one order of magnitude higher than that in the scums. A total of 36 types of MPs were found in the septic tank, and 26 types were found in both sediments and scums, but the type in the scums was 21% higher than that in the sediments. The size was mostly 20-100 μm, accounting for 86.3% and 91.2% in the sediments and scums, respectively. Four shapes of MPs were detected in the septic tank, namely, fiber, bead, granule, and fragment. Our study revealed that septic tanks are both sinks and sources of MPs, which are reflected in the fact that MPs are not only large in number but also abundant in types. Thus, significant attention should be paid to septic tank-based microplastic pollution, which may lead to environmental and health risks without proper control and management.

Bioremediation of hazardous pollutants from agricultural soils: A sustainable approach for waste management towards urban sustainability

Soil contamination is perhaps the most hazardous issue all over the world; these emerging pollutants ought to be treated to confirm the safety of our living environment. Fast industrialization and anthropogenic exercises have resulted in different ecological contamination and caused serious dangerous health effects to humans and animals. Agro wastes are exceptionally directed because of their high biodegradability. Effluents from the agro-industry are a possibly high environmental risk that requires suitable, low-cost, and extensive treatment. Soil treatment using a bioremediation method is considered an eco-accommodating and reasonable strategy for removing toxic pollutants from agricultural fields. The present review was led to survey bioremediation treatability of agro soil by microbes, decide functional consequences for microbial performance and assess potential systems to diminish over potentials. The presence of hazardous pollutants in agricultural soil and sources, and toxic health effects on humans has been addressed in this review. The present review emphasizes an outline of bioremediation for the effective removal of toxic contaminants in the agro field. In addition, factors influencing recent advancements in the bioremediation process have been discussed. The review further highlights the roles and mechanisms of micro-organisms in the bioremediation of agricultural fields.

Plastic is in the air: Impact of micro-nanoplastics from airborne pollution on Tillandsia usneoides (L.) L. (Bromeliaceae) as a possible green sensor

Due to the increasing evidence of widespread plastic pollution in the air, the impact on plants of airborne particles of polycarbonate (PC), polyethyleneterephthalate (PET), polyethylene (PE), and polyvinylchloride (PVC) was tested by administering pristine and aged airborne micro-nanoplastics (MNPs) to Tillandsia usneoides for two weeks. Here we showed that exposure to pristine MNPs, significantly reduced plant growth with respect to controls. Particularly, PVC almost halved plant development at the end of the treatment, while the other plastics exerted negative effects on growth only at the beginning of the exposure, with final stages comparable to those of controls. Plants exposed to aged MNPs showed significantly decreased growth at early stages with PC, later in the growth with PE, and even later with PET. Aged PVC did not exert a toxic effect on plants. When present, the plastic-mediated reduction in plant growth was coupled with a decrease in photosynthetic activity and alterations in the plant concentration of macro- and micronutrients. The plastic particles were showed to adhere to the plant surface and, preferentially, on the trichome wings. Our results reported, for the first time, evidence of negative effects of airborne plastic pollution on plant health, thus raising concerns for related environmental risks.

Comment on the paper 'Soil microplastic pollution under different land uses in tropics, southwestern China'

Research on soil microplastics is currently at an early stage, and there is no widely approved sampling protocol. Even so, any basic research should minimize errors to ensure that they are not amplified in future research. This paper examines some weaknesses of the original research paper 'Soil microplastic pollution under different land uses in tropics, southwestern China' recently published in this journal. The authors neglected to report the equipment used for soil sampling and did not use field blank samples. There is also a soil layer that was incorrectly named. The type and pore size of filter paper used for filtration during pre-analytical soil sample preparation is very important. In this paper the nature of the filter paper used, and its larger pore sizes are questionable by today's scientists. In addition, the authors in the original paper also overlooked reporting the statistical package used for statical analysis and ensuring if all data sets obey normality, homogeneity, and equality before running the one-way ANOVA test. This statistical step is widely considered mandatory, especially in the soil science community. So, this makes it difficult to trust the results documented. Furthermore, in the original paper, the needle and stereo microscope instruments used to sort microplastic-like materials prior to proper analysis are not reliable.