Recent trends in the liquid chromatography–mass spectrometry analysis of organic contaminants in environmental samples

Contaminants of emerging concern: Occurrence, analytical techniques, and removal with electrochemical advanced oxidation processes with special emphasis in Latin America

The occurrence of contaminants of emerging concern (CECs) in environmental systems is gradually more studied worldwide. However, in Latin America, the presence of contaminants of emerging concern, together with their environmental and toxicological impacts, has recently been gaining wide interest in the scientific community. This paper presents a critical review about the source, fate, and occurrence of distinct emerging contaminants reported during the last two decades in various countries of Latin America. In recent years, Brazil, Chile, and Colombia are the main countries that have conducted research on the presence of these pollutants in biological and aquatic compartments. Data gathered indicated that pharmaceuticals, pesticides, and personal care products are the most assessed CECs in Latin America, being the most common compounds the followings: atrazine, acenaphthene, caffeine, carbamazepine, ciprofloxacin, diclofenac, diuron, estrone, losartan, sulfamethoxazole, and trimethoprim. Most common analytical methodologies for identifying these compounds were HPLC and GC coupled with mass spectrometry with the potential to characterize and quantify complex substances in the environment at low concentrations. Most CECs' monitoring and detection were observed near to urban areas which confirm the out-of-date wastewater treatment plants and sanitization infrastructures limiting the removal of these pollutants. Therefore, the implementation of tertiary treatment should be required. In this tenor, this review also summarizes some studies of CECs removal using electrochemical advanced oxidation processes that showed satisfactory performance. Finally, challenges, recommendations, and future perspectives are discussed.

Improved pH measurement of mobile phases in reversed-phase liquid chromatography

Mobile phase pH is a critically important parameter in reversed-phase liquid chromatographic (RPLC) separations involving analytes that display acidic or basic properties in the pH range used for the mobile phase. The main problem in measuring mobile phase pH lies in the fact that RPLC mobile phases are typically aqueous-organic mixtures. In addition to experimental difficulties, the pH values refer to different aqueous-organic compositions that cannot be correctly compared. Given this situation, the unified pH (wabspH, also termed as ) based on the absolute chemical potential of the solvated proton has been proposed as a rigorous way of characterising mobile phase acidity that is fully inter-comparable between mobile phases of any composition. Here we report the wabspH values of 78 reversed-phase liquid chromatography-mass spectrometry mobile phases that were carefully measured by potential differences in a symmetric cell with two glass electrode half-cells and almost ideal ionic liquid triethylamylammonium bis((trifluoromethyl)sulfonyl)imide [N2225][NTf2] salt bridge with multiple overlapping measurements. The system of altogether 300 ΔwabspH values was anchored to the pH value of standard pH 7.00 aqueous buffer solution. The consistency standard deviation of the whole set of measurements was 0.09 pH units. In addition to the differential potentiometric reference method, simpler measurement methods that use double junction reference or double junction combined electrodes were tested and were found suitable for routine laboratories if high accuracy is not required.

Biogenic synthesis of novel nanomaterials and their applications

Despite the many benefits derived from the unique features and practicality of nanoparticles, the release of their toxic by-products or products from the synthesis stage into the environment could negatively impact natural resources and organisms. The physical and chemical methods for nanoparticle synthesis involve high energy consumption and the use of hazardous chemicals, respectively, going against the principles of green chemistry. Biological methods of synthesis that rely on extracts from a broad range of natural plants, and microorganisms, such as fungi, bacteria, algae, and yeast, have emerged as viable alternatives to the physical and chemical methods. Nanoparticles synthesized through biogenic pathways are particularly useful for biological applications that have high concerns about contamination. Herein, we review the physical and chemical methods of nanoparticle synthesis and present a detailed overview of the biogenic methods used for the synthesis of different nanoparticles. The major points discussed in this study are the following: (1) the fundamentals of the physical and chemical methods of nanoparticle syntheses, (2) the use of different biological precursors (microorganisms and plant extracts) to synthesize gold, silver, selenium, iron, and other metal nanoparticles, and (3) the applications of biogenic nanoparticles in diverse fields of study, including the environment, health, material science, and analytical chemistry.

Multidimensional chromatography in environmental analysis: Comprehensive two-dimensional liquid versus gas chromatography

Analysis of complex environmental matrices poses an extreme challenge for analytical chemists due to the vast number of known and unknown compounds, with very diverse chemical and physical properties. The need for a holistic characterisation of this complexity has sparked the development of effective tools to unravel the chemical composition of such environmental samples. Multidimensional chromatographic methods, namely comprehensive two-dimensional (2D) gas and liquid chromatography (GC × GC and LC × LC, respectively), coupled to different detection systems have emerged as powerful tools with the capability to address this challenge. While GC × GC has steadily gained popularity in environmental analysis, LC × LC is surprisingly less attractive in this research field. This critical review article explores the potential reasons why LC × LC is not the dominant technique used in environmental analysis as compared to GC × GC, while simultaneously highlighting the quite unique role of LC × LC for the target and untargeted analysis of complex environmental matrices. The possible combinations of stationary phases, the important role of the interfacing valve as the heart of an LC × LC assembly, the existing optimization strategies for improving the separation power in the 2D chromatographic space, and the need for user-friendly mathematical tools for multidimensional data handling are also discussed. Finally, a set of practical measures are suggested to increase the use and secure the success of LC × LC in environmental analysis.

Pharmaceutical pollution of hospital effluents and municipal wastewaters of Eastern Canada

Quantification of drugs residues in wastewaters of different sources could help better understand contamination pathways, eventually leading to effluent regulation. However, limited data are available for hospital-derived wastewaters. Here, an analytical method based on automated on-line solid-phase extraction liquid chromatography tandem mass spectrometry (on-line SPE - UPLC-MS/MS) was developed for the quantification of multi-class pharmaceuticals in wastewaters. Filtrate phase and suspended solids (SPM) were both considered to evaluate the distribution of targeted analytes. Experimental design optimization involved testing different chromatographic columns, on-line SPE columns, and loading conditions for the filtrate phase, and different organic solvents and cleanup strategies for suspended solids. The selected methods were validated with suitable limits of detection, recovery, accuracy, and precision. A total of 30 hospital effluents and 6 wastewater treatment plants were sampled to evaluate concentrations in real field-collected samples. Certain pharmaceuticals were quantified at high levels such as caffeine at 670,000 ng/L in hospital wastewaters and hydroxyibuprofen at 49,000 ng/L in WWTP influents. SPM samples also had high contaminant concentrations such as ibuprofen at 31,000 ng/g in hospital effluents, fluoxetine at 529 ng/g in WWTP influents or clarithromycin at 295 ng/g in WWTP effluents. Distribution coefficients (K_d) and particle-associated fractions (Φ) indicate that pharmaceuticals tend to have better affinity to suspended solids in hospital wastewater than in municipal wastewaters. The results also bring arguments for at source treatment of these specific effluents before their introduction into urban wastewater systems.

Use of whole-cell bioreporters to assess bioavailability of contaminants in aquatic systems

Water contamination has become increasingly a critical global environmental issue that threatens human and ecosystems’ health. Monitoring and risk assessment of toxic pollutants in water bodies is essential to identifying water pollution treatment needs. Compared with the traditional monitoring approaches, environmental biosensing via whole-cell bioreporters (WCBs) has exhibited excellent capabilities for detecting bioavailability of multiple pollutants by providing a fast, simple, versatile and economical way for environmental risk assessment. The performance of WCBs is determined by its elements of construction, such as host strain, regulatory and reporter genes, as well as experimental conditions. Previously, numerous studies have focused on the design and construction of WCB rather than improving the detection process and commercialization of this technology. For investigators working in the environmental field, WCB can be used to detect pollutants is more important than how they are constructed. This work provides a review of the development of WCBs and a brief introduction to genetic construction strategies and aims to summarize key studies on the application of WCB technology in detection of water contaminants, including organic pollutants and heavy metals. In addition, the current status of commercialization of WCBs is highlighted.

(Bio)Sensing Strategies Based on Ionic Liquid-Functionalized Carbon Nanocomposites for Pharmaceuticals: Towards Greener Electrochemical Tools

The interaction of carbon-based nanomaterials and ionic liquids (ILs) has been thoroughly exploited for diverse electroanalytical solutions since the first report in 2003. This combination, either through covalent or non-covalent functionalization, takes advantage of the unique characteristics inherent to each material, resulting in synergistic effects that are conferred to the electrochemical (bio)sensing system. From one side, carbon nanomaterials offer miniaturization capacity with enhanced electron transfer rates at a reduced cost, whereas from the other side, ILs contribute as ecological dispersing media for the nanostructures, improving conductivity and biocompatibility. The present review focuses on the use of this interesting type of nanocomposites for the development of (bio)sensors specifically for pharmaceutical detection, with emphasis on the analytical (bio)sensing features. The literature search displayed the conjugation of more than 20 different ILs and several carbon nanomaterials (MWCNT, SWCNT, graphene, carbon nanofibers, fullerene, and carbon quantum dots, among others) that were applied for a large set (about 60) of pharmaceutical compounds. This great variability causes a straightforward comparison between sensors to be a challenging task. Undoubtedly, electrochemical sensors based on the conjugation of carbon nanomaterials with ILs can potentially be established as sustainable analytical tools and viable alternatives to more traditional methods, especially concerning in situ environmental analysis.

Phycoremediation integrated approach for the removal of pharmaceuticals and personal care products from wastewater - A review

Pharmaceuticals and personal care products (PPCPs) are of emerging concerns because of their large usage, persistent nature which promised their continuous disposal into the environment, as these pollutants are stable enough to pass through wastewater treatment plants causing hazardous effects on all the organisms through bioaccumulation, biomagnification, and bioconcentration. The available technologies are not capable of eliminating all the PPCPs along with their degraded products but phycoremediation has the advantage over these technologies by biodegrading the pollutants without developing resistant genes. Even though phycoremediation has many advantages, industries have found difficulty in adapting this technology as a single-stage treatment process. To overcome these drawbacks recent research studies have focused on developing technology that integrated phycoremediation with the commonly employed treatment processes that are in operation for treating the PPCPs effectively. This review paper focuses on such research approaches that focused on integrating phycoremediation with other technologies such as activated sludge process (ASP), advanced oxidation process (AOP), Up-flow anaerobic sludge blanket reactor (UASBR), UV irradiation, and constructed wetland (CW) with the advantages and limitations of each integration processes. Furthermore, augmenting phycoremediation by co-metabolic mechanism with the addition of sodium chloride, sodium acetate, and glucose for the removal of PPCPs has been highlighted in this review paper.

Utilizing a Rapid Multi-Plug Filtration Cleanup Method for 72 Pesticide Residues in Grape Wines Followed by Detection with Gas Chromatography Tandem Mass Spectrometry

A convenient and fast multi-residue method for the efficient identification and quantification of 72 pesticides belonging to different chemical classes in red and white grape wines has been developed. The analysis was based on gas chromatography tandem quadrupole mass spectrometric determination (GC-MS/MS). The optimization strategy involved the selection of the amount of multi-walled carbon nanotubes (MWCNTs) and the number of cleanup procedure cycles for multi-plug filtration cleanup (m-PFC) to achieve ideal recoveries and reduce the sample matrix compounds in the final extracts. The optimized procedure obtained consistent recoveries between 70.2 and 108.8% (70.2 and 108.8% for white wine, and 72.3 and 108.4% for red wine), with relative standard deviations (RSDs) that were generally lower than 9.2% at the three spiking levels of 0.01, 0.05 and 0.1 mg/kg. The linearity was studied in the range between 0.002 and 0.1 mg/kg using pesticide standards prepared both in pure solvent and in the presence of the matrix, showing coefficients of determination (R²) higher than 0.9495 for all the pesticides. To improve accuracy, matrix-matched calibration curves were used for calculating the quantification results. Finally, the method was used successfully for detecting pesticide residues in commercial grape wines.

A method for detecting perfluorooctanoic acid and perfluorooctane sulfonate in water samples using genetically engineered bacterial biosensor

A simple, reagent and pre-treatment (i.e. dilution, sample purification and pH adjustment) free approach based genetically engineered bacterial biosensor is developed and demonstrated for the detection of perfluorinated compounds in water samples. The bacterial biosensor was developed by integrating two genes called regulatory (defluorinase gene) and reporter gene (green fluorescence gene) through genetic engineering techniques. The as-developed bacterial biosensor was employed to detect perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in water samples upon induction of regulatory gene and expression of green fluorescence protein. The induced fluorescence emission by the biosensor was visualized using fluorescence microscopic images. The specificity of biosensor was evaluated with different types of organic pollutants such as chlorinated compounds, polyaromatic hydrocarbons and pesticides etc., in both presence and absence of PFOA and PFOS. The biosensor was employed to detect the perfluorinated compounds at nano gram level in both standard solutions and natural water samples like river water, wastewater and drinking water with an analysis time of 24 h. The detection of PFOA and PFOS by the developed-bacterial sensor is validated by liquid chromatography coupled with mass spectrometer. The developed biosensor has demonstrated a rapid and sensitive detection of PFOA and PFOS in various water samples.

Overview of Sample Preparation and Chromatographic Methods to Analysis Pharmaceutical Active Compounds in Waters Matrices

In the environment, pharmaceutical residues are a field of particular interest due to the adverse effects to either human health or aquatic and soil environment. Because of the diversity of these compounds, at least 3000 substances were identified and categorized into 49 different therapeutic classes, and several actions are urgently required at multiple steps, the main ones: (i) occurrence studies of pharmaceutical active compounds (PhACs) in the water cycle; (ii) the analysis of the potential impact of their introduction into the aquatic environment; (iii) the removal/degradation of the pharmaceutical compounds; and, (iv) the development of more sensible and selective analytical methods to their monitorization. This review aims to present the current state-of-the-art sample preparation methods and chromatographic analysis applied to the study of PhACs in water matrices by pinpointing their advantages and drawbacks. Because it is almost impossible to be comprehensive in all PhACs, instruments, extraction techniques, and applications, this overview focuses on works that were published in the last ten years, mainly those applicable to water matrices.

A Multifunctional Tb-MOF Detector for H2O2, Fe3+, Cr2O7 2-, and TPA Explosive Featuring Coexistence of Binuclear and Tetranuclear Clusters

A novel three-dimensional microporous terbium(III) metal-organic framework (Tb-MOF) named as [Tb10 (DBA)6(OH)4(H2O)5]·(H3O)4 (1), was successfully obtained by a solvothermal method based on terbium nitrate and 5-di(2',4'-dicarboxylphenyl) benzoic acid (H5DBA). The Tb-MOF has been characterized by single crystal X-ray diffraction, elemental analysis, thermogravimetry, and fluorescence properties, and the purity was further confirmed by powder X-ray diffraction (PXRD) analysis. Structural analysis shows that there are two kinds of metal cluster species: binuclear and tetranuclear, which are linked by H5DBA ligands in two μ7 high coordination fashions into a three-dimensional microporous framework. Fluorescence studies show that the Tb-MOF can detect H2O2, Fe3+, and Cr2O7 2- with high sensitivity and selectivity and can also be used for electrochemical detection of exposed 2,4,6-trinitrophenylamine (TPA) in water. The highly selective and sensitive detection ability of the Tb-MOF might make it a potential multifunctional sensor in the future.

Seasonal performance assessment of four riverbank filtration sites by combined non-target and effect-directed analysis

Targeting the most relevant organic micropollutants (OMP) in routine analysis appears difficult due to formation of transformation products of unknown concentration or toxicity. Performance assessment of water purification processes is still based upon limited target data. Therefore, we broadened the assessment of the removal efficiencies with combined non-target and effect-directed analysis at four riverbank filtration (RBF) sites in Germany. To assess micropollutant elimination, constancy and formation during different seasons, considering local redox conditions, travel distances and total component number in the river, non-target analysis features were grouped into categories. Furthermore, RBF sites were investigated with four endpoints (baseline toxicity, acetylcholinesterase inhibition, antibiotic effects and estrogenic effects) for thin-layer chromatography - effect-directed analysis for the first time. Results showed elimination or reduction of many features and effects, but also constancy and formation of varying proportions. Fall river samples showed precipitation-caused dilution in both tests. Spring samples showed increased effects only in acetylcholinesterase inhibition and estrogenic effects, probably due to phytoestrogens or algae bloom during vegetation period. Sites were ranked considering the total number of features, group proportions, seasonal variations and intensity and number of effects in abstraction wells. Oxic conditions and low initial component numbers in the river (Ruhr sites) resulted in less effects and fewer formations. Longer travel distances were important for a more efficient reduction of effects and features. Combination of non-target and effect-directed analysis proved to be valuable for a more comprehensive assessment of process performance beyond target analysis as also unknown OMP are observed with both methods.

Multiplexed Immunosensor Based on the Amperometric Transduction for Monitoring of Marine Pollutants in Sea Water

Environmental pollutants vigilance is one of the main problems that the aquaculture industry has to face with the objective to ensure the quality of their products and prevent entrance in the food chain that finally may arrive to the consumer. Contaminants such as hormones, antibiotics or biocides are especially relevant due to their toxicity, pharmacological effect or hormonal activity that can be considered harmful for the final consumer. The contaminants can be detected in the environment where the food is growing, and their concentration can be found (i.e., seawater) in the range of µg·L⁻¹, ng·L⁻¹ or even in lower concentrations. Thus, sensitive and selective methods for their monitoring are required to avoid their arrival in the food chain. Here, the development of a multiplexed amperometric biosensor is described, based on the use of specific antibodies to reach the necessary detectability to measure the targeted contaminants directly in seawater. The multiplexed immunosensor allows the detection of four relevant pollutants, such as el Irgarol 1051, sulfapyridine, chloramphenicol and estradiol, reaching an IC₅₀ of 5.04 ± 0.29, 3.45 ± 0.29, 4.17 ± 0.44 and 5.94 ± 0.28 µg·L⁻¹, directly measured in seawater.

Application of Nanostructured Carbon-Based Electrochemical (Bio)Sensors for Screening of Emerging Pharmaceutical Pollutants in Waters and Aquatic Species: A Review

Pharmaceuticals, as a contaminant of emergent concern, are being released uncontrollably into the environment potentially causing hazardous effects to aquatic ecosystems and consequently to human health. In the absence of well-established monitoring programs, one can only imagine the full extent of this problem and so there is an urgent need for the development of extremely sensitive, portable, and low-cost devices to perform analysis. Carbon-based nanomaterials are the most used nanostructures in (bio)sensors construction attributed to their facile and well-characterized production methods, commercial availability, reduced cost, high chemical stability, and low toxicity. However, most importantly, their relatively good conductivity enabling appropriate electron transfer rates-as well as their high surface area yielding attachment and extraordinary loading capacity for biomolecules-have been relevant and desirable features, justifying the key role that they have been playing, and will continue to play, in electrochemical (bio)sensor development. The present review outlines the contribution of carbon nanomaterials (carbon nanotubes, graphene, fullerene, carbon nanofibers, carbon black, carbon nanopowder, biochar nanoparticles, and graphite oxide), used alone or combined with other (nano)materials, to the field of environmental (bio)sensing, and more specifically, to pharmaceutical pollutants analysis in waters and aquatic species. The main trends of this field of research are also addressed.

Monitoring pharmaceuticals in the aquatic environment using enzyme-linked immunosorbent assay (ELISA)-a practical overview

The presence of pharmaceuticals, which are considered as contaminants of emerging concern, in natural waters is currently recognized as a widespread problem. Monitoring these contaminants in the environment has been an important field of research since their presence can affect the ecosystems even at very low levels. Several analytical techniques have been developed to detect and quantify trace concentrations of these contaminants in the aquatic environment, namely high-performance liquid chromatography, gas chromatography, and capillary electrophoresis, usually coupled to different types of detectors, which need to be complemented with time-consuming and costly sample cleaning and pre-concentration procedures. Generally, the enzyme-linked immunosorbent assay (ELISA), as other immunoassay methodologies, is mostly used in biological samples (most frequently urine and blood). However, during the last years, the number of studies referring the use of ELISA for the analysis of pharmaceuticals in complex environmental samples has been growing. Therefore, this work aims to present an overview of the application of ELISA for screening and quantification of pharmaceuticals in the aquatic environment, namely in water samples and biological tissues. The experimental procedures together with the main advantages and limitations of the assay are addressed, as well as new incomes related with the application of molecular imprinted polymers to mimic antibodies in similar, but alternative, approaches. Graphical Abstract.

Comparison of Fragmentation Techniques for the Structural Characterization of Singly Charged Agrochemicals

Investigating the structure of active ingredients, such as agrochemicals and their associated metabolites, is a crucial requisite in the discovery and development of these molecules. In this study, structural characterization by electron-induced dissociation (EID) was compared to collisionally activated dissociation (CAD) on a series of agrochemicals. EID fragmentation produced a greater variety of fragment ions and complementary ion pairs leading to more complete functional group characterization compared to CAD. The results obtained displayed many more cross-ring fragmentation of the pyrimidine ring compared to the pyridine ring. Compounds that consisted of one aromatic heterocyclic moiety (azoxystrobin, fluazifop acid, fluazifop-p-butyl, and pirimiphos-methyl) displayed cross-ring fragmentation while compounds with only aromatic hydrocarbon rings (fenpropidin and S-metolachlor) displayed no cross-ring fragmentation. The advantages of high-resolution accurate mass spectrometry (HRAM MS) are shown with the majority of assignments at ppb range error values and the ability to differentiate ions with the same nominal mass but different elemental composition. This highlights the potential for HRAM MS and EID to be used as a tool for structural characterization of small molecules with a wide variety of functional groups and structural motifs.

Two d10 luminescent metal–organic frameworks as dual functional luminescent sensors for (Fe3+,Cu2+) and 2,4,6-trinitrophenol (TNP) with high selectivity and sensitivity

Two luminescent 3D supramolecular structures which serve as effective luminescent sensors for Fe³⁺, Cu²⁺ and TNP via luminescent quenching have been synthesized under solvothermal conditions.

Method development for simultaneous determination of polar and nonpolar pesticides in surface water by low-temperature partitioning extraction (LTPE) followed by HPLC-ESI-MS/MS

During this research, chemometric approaches were applied for optimization of the low-temperature partitioning extraction (LTPE) for the simultaneous analysis of the pesticides: acephate, difenoconazole, fenamidone, fluazifop, fluazinam, methamidophos, and thiamethoxam from surface water samples and determination by high-performance liquid chromatography-electrospray ionization-tandem mass spectrometry. It was used the 2³ full factorial and the Doehlert experimental designs. The extraction technique was optimized by evaluating the effects of the three variables: sample pH, ionic strength (addition of Na₂HPO₄), and organic solvent volume. Considering the interest to find an optimal condition for all analytes simultaneously, the best extraction parameters found were as follows: pH = 5.33, concentration of Na₂HPO₄ = 0.0088 mol L^-1 and organic phase volume = 4.5 mL. The optimized methodology showed LOD and LOQ levels from 0.33 to 8.13 ng L^-1 and from 1.09 to 26.84 ng L^-1, respectively. The recovery values ranged from 38.37 and 99.83% and the RSD values varied from 2.33 to 18.92%. The method was applied to surface water analysis sampled in areas with intensive agricultural practices in Ouro Branco City, Minas Gerais, Brazil. The difenoconazole was detected in concentrations between 12.53 and 94.76 ng L^-1.

Non-targeted Screening in Environmental Monitoring Programs

Contaminant monitoring programs have been tasked with understanding the fate and transport of toxic chemicals in the environment. Mass spectrometry based methods have traditionally been developed to maximize sensitivity and accuracy of a select set of target compounds. As mass spectrometry methods have advanced, so has the breadth of questions proposed by environmental chemists. Incorporating these methods in chemical monitoring programs provides large data sets to explore the effects of complex mixtures on environmental systems.

High Flow-Rate Sample Loading in Large Volume Whole Water Organic Trace Analysis Using Positive Pressure and Finely Ground Sand as a SPE-Column In-Line Filter

By using an innovative, positive pressure sample loading technique in combination with an in-line filter of finely ground sand the bottleneck of solid phase extraction (SPE) can be reduced. Recently published work by us has shown the proof of concept of the technique. In this work, emphasis is put on the SPE flow rate and method validation for 26 compounds of emerging environmental concern, mainly from the 1st and 2nd EU Watch List, with various physicochemical properties. The mean absolute recoveries in % and relative standard deviations (RSD) in % for the investigated compounds from spiked pure water samples at the three investigated flow rates of 10, 20, and 40 mL/min were 63.2% (3.2%), 66.9% (3.3%), and 69.0% (4.0%), respectively. All three flow rates produced highly repeatable results, and this allowed a flow rate increase of up to 40 mL/min for a 200 mg, 6 mL, reversed phase SPE cartridge without compromising the recoveries. This figure is more than four times the maximum flow rate recommended by manufacturers. It was indicated that some compounds, especially pronounced for the investigated macrolide molecules, might suffer when long contact times with the sample glass bottle occurs. A reduced contact time somewhat decreases this complication. A very good repeatability also held true for experiments on both spiked matrix-rich pond water (high and low concentrations) and recipient waters (river and wastewater) applying 40 mL/min. This work has shown that, for a large number of compounds of widely differing physicochemical properties, there is a generous flow rate window from 10 to 40 mL/min where sample loading can be conducted. A sample volume of 0.5 L, which at the recommended maximum flow rate speed of 10 mL/min, would previously take 50 min, can now be processed in 12 min using a flow rate of 40 mL/min. This saves 38 min per processed sample. This low-cost technology allows the sample to be transferred to the SPE-column, closer to the sample location and by the person taking the sample. This further means that only the sample cartridge would need to be sent to the laboratory, instead of the whole water sample, like today’s procedure.

Multi-residue analysis of 44 pharmaceutical compounds in environmental water samples by solid-phase extraction coupled to liquid chromatography-tandem mass spectrometry

A solid-phase extraction combined with a liquid chromatography-tandem mass spectrometry analysis has been developed and validated for the simultaneous determination of 44 pharmaceuticals belonging to different therapeutic classes (i.e., antibiotics, anti-inflammatories, cardiovascular agents, hormones, neuroleptics, and anxiolytics) in water samples. The sample preparation was optimized by studying target compounds retrieval after the following processes: i) water filtration, ii) solid phase extraction using Waters Oasis HLB cartridges at various pH, and iii) several evaporation techniques. The method was then validated by the analysis of spiked estuarine waters and wastewaters before and after treatment. Analytical performances were evaluated in terms of linearity, accuracy, precision, detection, and quantification limits. Recoveries of the pharmaceuticals were acceptable, instrumental detection limits varied between 0.001 and 25 pg injected and method quantification limits ranged from 0.01 to 30.3 ng/L. The precision of the method, calculated as relative standard deviation, ranged from 0.3 to 49.4%. This procedure has been successfully applied to the determination of the target analytes in estuarine waters and wastewaters. Eight of these 44 pharmaceuticals were detected in estuarine water, while 26 of them were detected in wastewater effluent. As expected, the highest values of occurrence and concentration were found in wastewater influent.

Assessment of 83 pharmaceuticals in WWTP influent and effluent samples by UHPLC-MS/MS: Hourly variation

The removal efficiency of pharmaceuticals in wastewater treatment plants (WWTPs) is variable and some of these compounds pass these plants almost intact and others presenting a removal efficiency close to 100%. Their incomplete removal results in a continuous discharge of pharmaceuticals into the environment. To assess the profile of contamination of influents and effluents over a day, a set of 83 pharmaceuticals were evaluated hourly in a WWTP in Leiria, Portugal. The composite samples of the influent and effluent were also collected. Concentrations varied from <MDL for ketoprofen, clarithromycin, ofloxacin, and diltiazem to 63.97 μg/L for caffeine in the WWTP influent composite sample and <MDL for clarithromycin, bupropion, and diltiazem to 2.01 μg/L for O-desmethylvenlafaxine for effluent composite sample. Concentrations in the range of μg/L were found for hydroxyibuprofen, salicylic acid, d,l-norephedrine, and caffeine in the WWTP influent, and diclofenac, carbamazepine, O-desmethylvenlafaxine in the WWTP effluents. For the samples collected hourly, thirty-eight and twenty-nine pharmaceuticals were detected in at least one WWTP sample. In the WWTP influent the total concentration of detected pharmaceuticals was higher between 15 and 22 h and lower in the period from 23 to 10 h in the morning. In the WWTP effluent, a slight variation was noticed throughout the sampling hours. Carbamazepine, fluoxetine, sertraline, atorvastatin, caffeine, simvastatin, and trazodone were the pharmaceuticals with risk quotient (RQ) >1 in WWTP influents, and carbamazepine, fluoxetine, sertraline the pharmaceuticals with an RQ > 1 in WWTP effluents.

Mass spectrometric strategies for the investigation of biomarkers of illicit drug use in wastewater

The analysis of illicit drugs in urban wastewater is the basis of wastewater-based epidemiology (WBE), and has received much scientific attention because the concentrations measured can be used as a new non-intrusive tool to provide evidence-based and real-time estimates of community-wide drug consumption. Moreover, WBE allows monitoring patterns and spatial and temporal trends of drug use. Although information and expertise from other disciplines is required to refine and effectively apply WBE, analytical chemistry is the fundamental driver in this field. The use of advanced analytical techniques, commonly based on combined chromatography-mass spectrometry, is mandatory because the very low analyte concentration and the complexity of samples (raw wastewater) make quantification and identification/confirmation of illicit drug biomarkers (IDBs) troublesome. We review the most-recent literature available (mostly from the last 5 years) on the determination of IDBs in wastewater with particular emphasis on the different analytical strategies applied. The predominance of liquid chromatography coupled to tandem mass spectrometry to quantify target IDBs and the essence to produce reliable and comparable results is illustrated. Accordingly, the importance to perform inter-laboratory exercises and the need to analyze appropriate quality controls in each sample sequence is highlighted. Other crucial steps in WBE, such as sample collection and sample pre-treatment, are briefly and carefully discussed. The article further focuses on the potential of high-resolution mass spectrometry. Different approaches for target and non-target analysis are discussed, and the interest to perform experiments under laboratory-controlled conditions, as a complementary tool to investigate related compounds (e.g., minor metabolites and/or transformation products in wastewater) is treated. The article ends up with the trends and future perspectives in this field from the authors' point of view. © 2016 Wiley Periodicals, Inc. Mass Spec Rev 37:258-280, 2018.

A comparison of three liquid chromatography (LC) retention time prediction models

High-resolution mass spectrometry (HRMS) data has revolutionized the identification of environmental contaminants through non-targeted analysis (NTA). However, chemical identification remains challenging due to the vast number of unknown molecular features typically observed in environmental samples. Advanced data processing techniques are required to improve chemical identification workflows. The ideal workflow brings together a variety of data and tools to increase the certainty of identification. One such tool is chromatographic retention time (RT) prediction, which can be used to reduce the number of possible suspect chemicals within an observed RT window. This paper compares the relative predictive ability and applicability to NTA workflows of three RT prediction models: (1) a logP (octanol-water partition coefficient)-based model using EPI Suite™ logP predictions; (2) a commercially available ACD/ChromGenius model; and, (3) a newly developed Quantitative Structure Retention Relationship model called OPERA-RT. Models were developed using the same training set of 78 compounds with experimental RT data and evaluated for external predictivity on an identical test set of 19 compounds. Both the ACD/ChromGenius and OPERA-RT models outperformed the EPI Suite™ logP-based RT model (R² = 0.81-0.92, 0.86-0.83, 0.66-0.69 for training-test sets, respectively). Further, both OPERA-RT and ACD/ChromGenius predicted 95% of RTs within a ± 15% chromatographic time window of experimental RTs. Based on these results, we simulated an NTA workflow with a ten-fold larger list of candidate structures generated for formulae of the known test set chemicals using the U.S. EPA's CompTox Chemistry Dashboard (https://comptox.epa.gov/dashboard), RTs for all candidates were predicted using both ACD/ChromGenius and OPERA-RT, and RT screening windows were assessed for their ability to filter out unlikely candidate chemicals and enhance potential identification. Compared to ACD/ChromGenius, OPERA-RT screened out a greater percentage of candidate structures within a 3-min RT window (60% vs. 40%) but retained fewer of the known chemicals (42% vs. 83%). By several metrics, the OPERA-RT model, generated as a proof-of-concept using a limited set of open source data, performed as well as the commercial tool ACD/ChromGenius when constrained to the same small training and test sets. As the availability of RT data increases, we expect the OPERA-RT model's predictive ability will increase.

Metal-Organic Framework-Based Sensors for Environmental Contaminant Sensing

Increasing demand for timely and accurate environmental pollution monitoring and control requires new sensing techniques with outstanding performance, i.e., high sensitivity, high selectivity, and reliability. Metal-organic frameworks (MOFs), also known as porous coordination polymers, are a fascinating class of highly ordered crystalline coordination polymers formed by the coordination of metal ions/clusters and organic bridging linkers/ligands. Owing to their unique structures and properties, i.e., high surface area, tailorable pore size, high density of active sites, and high catalytic activity, various MOF-based sensing platforms have been reported for environmental contaminant detection including anions, heavy metal ions, organic compounds, and gases. In this review, recent progress in MOF-based environmental sensors is introduced with a focus on optical, electrochemical, and field-effect transistor sensors. The sensors have shown unique and promising performance in water and gas contaminant sensing. Moreover, by incorporation with other functional materials, MOF-based composites can greatly improve the sensor performance. The current limitations and future directions of MOF-based sensors are also discussed.

Development of a comprehensive screening method for more than 300 organic chemicals in water samples using a combination of solid-phase extraction and liquid chromatography-time-of-flight-mass spectrometry

A comprehensive screening method for 311 organic compounds with a wide range of physicochemical properties (log Pow -2.2-8.53) in water samples was developed by combining solid-phase extraction with liquid chromatography-high-resolution time-of-flight mass spectrometry. Method optimization using 128 pesticides revealed that tandem extraction with styrene-divinylbenzene polymer and activated carbon solid-phase extraction cartridges at pH 7.0 was optimal. The developed screening method was able to extract 190 model compounds with average recovery of 80.8% and average relative standard deviations (RSD) of 13.5% from spiked reagent water at 0.20 μg L^-1, and 87.1% recovery and 10.8% RSD at 0.05 μg L^-1. Spike-recovery testing (0.20 μg L^-1) using real sewage treatment plant effluents resulted in an average recovery and average RSD of 190 model compounds of 77.4 and 13.1%, respectively. The method was applied to the influent and effluent of five sewage treatment plants in Kitakyushu, Japan, with 29 out of 311 analytes being observed at least once. The results showed that this method can screen for a large number of chemicals with a wide range of physicochemical properties quickly and at low operational cost, something that is difficult to achieve using conventional analytical methods. This method will find utility in target screening of hazardous chemicals with a high risk in environmental waters, and for confirming the safety of water after environmental incidents.

Mussels as bioindicators of diclofenac contamination in coastal environments

Diclofenac a nonsteroidal anti-inflammatory drug (NSAID) has been confirmed as an emerging contaminant in the aquatic environment. Toxicology studies have revealed that harmful effects may emerge from diclofenac presence not only for human health, but also for marine organisms, which implies its monitoring. To overcome the demanding challenges of diclofenac quantification in biotic aquatic species, a novel method for the determination of diclofenac in mussels (Mytilus galloprovincialis and Mytilus edulis) and macroalgae (Laminaria digitata) using high performance liquid chromatography coupled to tandem mass spectrometry was developed and validated according to the EC Decision 2002/657/EC. Additionally, a study was done about diclofenac contamination in mussels collected from 8 sites along the 1115 miles of coastline in Portugal in 2015. The results suggested that levels in mussels are closely related to the environmental contamination. Therefore, mussels can be a potential bioindicator of diclofenac contamination in the coastal environment.

Quantitative analysis of amphiphilic N-alkyloxypyridinecarboximidamide by liquid chromatography-tandem mass spectrometry

LC–MS/MS method to determine hydrophobic N-alkyloxy substituted amidines: N-(2-ethylhexyloxy)pyridine-2-carboximidamide, N-(2-ethylhexyloxy)pyridine-3-carboximidamide, N-(2-ethylhexyloxy)pyridine-4-carboximidamide, N-decyloxy pyridine-2-carboximidamide, N-decyloxypyridine-3-carboximidamide and N-decyloxypyridine-4-carboximidamide was developed and validated in terms of linearity, precision and accuracy. The developed method was successfully applied to monitor and control the synthesis process. The experimental data points indicated that the straight chain alkyl bromide reacted most rapidly than branched alkyl bromide and the enhancement of the reaction efficiency strongly depended on reaction temperature.

Monitoring the Behavior of Emerging Contaminants in Wastewater-Impacted Rivers Based on the Use of Fluorescence Excitation Emission Matrixes (EEM)

This study investigated the applicability of fluorescence indexes based on the interpretation of excitation emission matrices (EEMs) by PARAFAC analysis and by selecting fluorescence intensities at a priori defined excitation/emission pairs as surrogates for monitoring the behavior of emerging organic compounds (EOCs) in two catchment basins impacted by wastewater discharges. Relevant EOC and EEM data were obtained for a 90 km stretch of the Simeto River, the main river in Sicily, and the smaller San Leonardo River, which was investigated for a 17 km stretch. The use of fluorescence indexes developed by these two different approaches resulted in similar observations. Changes of the fluorescence indexes that correspond to a group of humic-like fluorescing species were determined to be highly correlated with the concentrations of recalcitrant contaminants such as sucralose, sulfamethoxazole and carbamazepine, which are typical wastewater markers in river water. Changes of the fluorescence indexes related to tyrosine-like substances were well correlated with the concentrations of ibuprofen and caffeine, anthropogenic indicators of untreated wastewater discharges. Chemical oxygen demand and dissolved organic carbon concentrations were correlated with humic-like fluorescence indexes. The observed correlations were site-specific and characterized by different regression parameters for every collection event. Caffeine and carbamazepine showed correlations with florescence indexes in the San Leonardo River and in the alluvial plain stretch of the Simeto River, whereas sucralose, sulfamethoxazole and ibuprofen have always been well correlated in all the investigated river stretches. However, when data of different collection events from river stretches where correlations were observed were combined, good linear correlations were obtained for data sets generated via the normalization of the measured concentrations by the average value for the corresponding collection event. These results show that fluorescence based indexes can be used to monitor the behavior of some trace organic contaminants in wastewater impacted rivers and to track wastewater discharges in streams and rivers.

Exposure Marker Discovery of Phthalates Using Mass Spectrometry

Phthalates are chemicals widely used in industry and the consequences on human health caused by exposure to these agents are of significant interest currently. The urinary metabolites of phthalates can be measured and used as exposure markers for the assessment of the actual internal contamination of phthalates coming from different sources and absorbed by various ways. The purpose of this paper is to review the markers for exposure and risk assessment of phthalates such as di-methyl phthalate (DMP), di-ethyl phthalate (DEP), di-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl)phthalate (DEHP), di-(2-propylheptyl)phthalate (DPHP), di-iso-nonyl phthalate (DINP), di-n-octyl phthalate (DnOP) and di-iso-decyl phthalate (DIDP), and introduction of the analytical approach of three metabolomics data processing approaches that can be used for chemical exposure marker discovery in urine with high-resolution mass spectrometry (HRMS) data.

Nontargeted homologue series extraction from hyphenated high resolution mass spectrometry data

BACKGROUND

A large proportion of polar anthropogenic compounds routinely released into the environment comprises homologue series, i.e., sets of chemicals differing in a repeating chemical unit. Using analytical techniques such as liquid chromatography coupled to high-resolution mass spectrometry (LC-HRMS), these compounds are readily measurable as signal sets with characteristic differences in mass and typically retention time. However, and despite such distinct characteristics, no computational approach for the direct, simultaneous and untargeted detection of all such signal sets comprising both LC and HRMS information has to date been presented.

RESULTS

A fast two-staged approach has been developed to extract LC-HRMS signal patterns which can be indicative of homologous analytes. In a first stage, a k-d tree representation of picked LC-HRMS peaks is used to extract all feasible 3-tuples of peaks with restrictions in, e.g., mass defect differences. A second stage then recombines these 3-tuples to larger series tuples while ensuring smooth changes in their retention time characteristics. This unsupervised approach was evaluated for ten effluent samples from Swiss sewage treatment plants (STPs), in both positive and negative electrospray-ionization.

CONCLUSIONS

Beside recovering all continuous series of previously identified homologues, substantial fractions of nontargeted peaks could subsequently be assigned into very diverse peak series, although assignments were often not unique. The latter ambiguities were resolved by a self-organizing map technique and revealed both distinctive series meshing and rivaling combinatorial solutions in the presence of isobaric or gapped series peaks. When comparing STPs, several ubiquitous yet partially low-frequent series mass differences emerged and may prioritize future identification efforts. The presented algorithm is freely available as part of the R package nontarget and as a user-friendly web-interface at www.envihomolog.eawag.ch.Graphical AbstractSearch for systematic series indicative of homologous compounds is based on a partitioned representation of LC-HRMS signal characteristics. This nontargeted search first extracts series triplets in a nearest-neighbour walk and then recombines them to larger ones. For illustration, the two dimensions involving mass defect characteristics are represented by one only.

Procedures of determining organic trace compounds in municipal sewage sludge-a review

Sewage sludge is the largest by-product generated during the wastewater treatment process. Since large amounts of sludge are being produced, different ways of disposal have been introduced. One tempting option is to use it as fertilizer in agricultural fields due to its high contents of inorganic nutrients. This, however, can be limited by the amount of trace contaminants in the sewage sludge, containing a variety of microbiological pollutants and pathogens but also inorganic and organic contaminants. The bioavailability and the effects of trace contaminants on the microorganisms of soil are still largely unknown as well as their mixture effects. Therefore, there is a need to analyze the sludge to test its suitability before further use. In this article, a variety of sampling, pretreatment, extraction, and analysis methods have been reviewed. Additionally, different organic trace compounds often found in the sewage sludge and their methods of analysis have been compiled. In addition to traditional Soxhlet extraction, the most common extraction methods of organic contaminants in sludge include ultrasonic extraction (USE), supercritical fluid extraction (SFE), microwave-assisted extraction (MAE), and pressurized liquid extraction (PLE) followed by instrumental analysis based on gas or liquid chromatography and mass spectrometry.

Development of potential candidate reference materials for drugs in bottom sediment, cod and herring tissues

Regular use of a reference material and participation in a proficiency testing program can improve the reliability of analytical data. This paper presents the preparation of candidate reference materials for the drugs metoprolol, propranolol, carbamazepine, naproxen, and acenocoumarol in freshwater bottom sediment and cod and herring tissues. These reference materials are not available commercially. Drugs (between 7 ng/g and 32 ng/g) were added to the samples, and the spiked samples were freeze-dried, pulverized, sieved, homogenized, bottled, and sterilized by γ-irradiation to prepare the candidate materials. Procedures for extraction and liquid chromatography coupled with tandem mass spectrometry were developed to determine the drugs of interest in the studied material. Each target drug was quantified using two analytical procedures, and the results obtained from these two procedures were in good agreement with each other. Stability and homogeneity assessments were performed, and the relative uncertainties due to instability (for an expiration date of 12 months) and inhomogeneity were 10-25% and 4.0-6.8%, respectively. These procedures will be useful in the future production of reference materials.

Spatial and seasonal variation of organic pollutants in surface water using multivariate statistical techniques

In this study, analysis of variance (ANOVA), cluster analysis (CA) and principal component analysis (PCA) were employed in order to evaluate the concentration profile of organic contaminants found in three main river from central Transylvania, Romania. Samples were collected from nine sampling stations, in two different sampling campaigns (wet season and dry season). Water samples were extracted using solid-phase extraction and analyzed using gas chromatography coupled with mass spectrometry (GC/MS). Twelve organic pollutants belonging to different classes were used for further interpretations. ANOVA highlighted compounds which distinguished Olt River from Mures River, and compounds that are influenced by increased river flow from the wet season. CA was applied to group the sampling stations. Three clusters were obtained, according to their organic load. PCA extracted five principal components explaining 87.330% from data set variability. Based on these results, a future monitoring study may be optimized by reducing the sampling points and compounds to those that are representative for each river, thereby reducing costs, without any information loss.

Development of a solid-phase extraction system modified for preconcentration of emerging contaminants in large sample volumes from rivers of the lagoon system in the city of Rio de Janeiro, Brazil

A single method modified for monitoring of emerging contaminants in river water was developed for large sample volumes. Water samples from rivers of the lagoon system in the city of Rio de Janeiro (Brazil) were analyzed by the SPE-HPLC-MS-TOF analytical method. Acetaminophen was detected in four rivers in the concentration range of 0.09μgL(-1) to 0.14μgL(-1). Salicylic acid was also found in the four rivers in the concentration range of 1.65μgL(-1) to 4.81μgL(-1). Bisphenol-A was detected in all rivers in the concentration range of 1.37μgL(-1) to 39.86μgL(-1). Diclofenac was found in only one river, with concentration of 0.22μgL(-1). The levels of emerging organic pollutants in the water samples of the Jacarepaguá hydrographical basin are significant. The compounds are not routinely monitored and present potential risks to environmental health.

Microbial toxicity and biodegradability of perfluorooctane sulfonate (PFOS) and shorter chain perfluoroalkyl and polyfluoroalkyl substances (PFASs)

Perfluorooctane sulfonate (PFOS) and related perfluoroalkyl and polyfluoroalkyl substances (PFASs) are emerging contaminants that have been widely applied in consumer and industrial applications for decades. However, PFOS has raised public concern due to its high bioaccumulative character, environmental persistence, and toxicity. Shorter PFASs such as perfluorobutane sulfonate (PFBS) and polyfluoroalkyl compounds have been proposed as alternatives to PFOS but it is unclear whether these fluorinated substances pose a risk for public health and the environment. The objective of this research was to investigate the microbial toxicity and the susceptibility to microbial degradation of PFOS and several related fluorinated compounds, i.e., short-chain perfluoroalkyl and polyfluoroalkyl sulfonic and carboxylic acids. None of the compounds tested were toxic to the methanogenic activity of anaerobic wastewater sludge even at very high concentrations (up to 500 mg L^-1). All PFASs evaluated were highly resistant to microbial degradation. PFOS was not reductively dehalogenated by the anaerobic microbial consortium even after very long periods of incubation (3.4 years). Similarly, the tested short chain perfluoroalkyl substances (i.e., PFBS and trifluoroacetic acid) and a polyfluoroalkyl PFOS analogue, 6 : 2 fluorotelomer sulfonic acid (FTSA) were also resistant to anaerobic biodegradation. Likewise, no conclusive evidence of microbial degradation was observed under aerobic conditions for any of the short-chain perfluoroalkyl and polyfluoroalkyl carboxylic acids tested after 32 weeks of incubation. Collectively, these results indicate that PFOS and its alternatives such as short chain perfluoroalkyl sulfonates and carboxylates and their polyfluorinated homologues are highly resistant to microbial degradation.