Comparison of Dorris–Gray and Schultz methods for the calculation of surface dispersive free energy by inverse gas chromatography

Evaluation of Polyvinyl Alcohol as Binder during Continuous Twin Screw Wet Granulation

Binder selection is a crucial step in continuous twin-screw wet granulation (TSWG), as the material experiences a much shorter residence time (2-40 s) in the granulator barrel compared to batch-wise granulation processes. Polyvinyl alcohol (PVA) 4-88 was identified as an effective binder during TSWG, but the potential of other PVA grades-differing in polymerization and hydrolysis degree-has not yet been studied. Therefore, the aim of the current study was to evaluate the potential of different PVA grades as a binder during TSWG. The breakage and drying behavior during the fluidized bed drying of drug-loaded granules containing the PVA grades was also studied. Three PVA grades (4-88, 18-88, and 40-88) were characterized and their attributes were compared to previously investigated binders by Vandevivere et al. through principal component analysis. Three binder clusters could be distinguished according to their attributes, whereby each cluster contained a PVA grade and a previously investigated binder. PVA 4-88 was the most effective binder of the PVA grades for both a good water-soluble and water-insoluble formulation. This could be attributed to its high total surface energy, low viscosity, good wettability of hydrophilic and hydrophobic surfaces, and good wettability by water of the binder. Compared to the previously investigated binders, all PVA grades were more effective in the water-insoluble formulation, as they yielded strong granules (friability below 30%) at lower L/S-ratios. This was linked to the high dispersive surface energy of the high-energy sites on the surface of PVA grades and their low surface tension. During fluidized bed drying, PVA grades proved suitable binders, as the acetaminophen (APAP) granules were dried within a short time due to the low L/S-ratio, at which high-quality granules could be produced. In addition, no attrition occurred, and strong tablets were obtained. Based on this study, PVA could be the preferred binder during twin screw granulation due to its high binder effectiveness at a low L/S-ratio, allowing efficient downstream processing. However, process robustness must be controlled by the included excipients, as PVA grades are operating in a narrow L/S-ratio range.

Exploring affinity between organic probes and Prussian Blue Analogues via inverse gas chromatography

Prussian Blue Analogues (PBAs), which are characterized by their open structure, high stability, and non-toxic properties, have recently been the subject of research for various applications, including their use as electrode precursors for capacitive deionization, gas storage, and environmental purification. These materials can be readily tailored to enhance their affinity towards gases for integration with sensing devices. An improved understanding of PBA-gas interactions is expected to enhance material development and existing sensor deposition schemes greatly. The use of inverse gas chromatography (IGC) is a robust approach for examining the relationship between porous materials and gases. In this study, the adsorption properties of (functionalized) hydrocarbons, i.e., probe molecules, on the copper hexacyanoferrate (CuHCF) lattice were studied via IGC, demonstrating that alkylbenzenes have a higher affinity for this material than n-alkanes. This difference was rationalized by steric hindrance, π-π interactions, and vapour pressure effects. Along the same line, the five isomers of hexane showed decreasing selectivity upon increased steric hindrance. Enthalpy values for n-pentane, n-hexane and n-heptane were lower than that of toluene. The introduction of increased probe masses resulted in a surface coverage of 46% for toluene. For all n-alkane probe molecules this percentage was lower. However, the isotherms of these probes did not show saturation points and the observed linear regime proves beneficial for gas sensing. Our work demonstrates the versatility of CuHCF for gas sensing purposes and the potential of IGC to characterize the adsorption characteristics of such a porous nanomaterial.

Tuning Electrode Work Function and Surface Energy for Solution Shearing High-Performance Organic Field-Effect Transistors

A bottom-contact organic field-effect transistor (OFET) is easily adaptable to the standard lithography process because the contact electrodes are deposited before the organic semiconductor (OSC). However, the low surface energy of bare electrodes limits utilizing solution-processed single-crystal OSCs. Additionally, the bare electrode usually leads to a significant charge injection barrier, owing to its relatively low work function (WF). Here, we simultaneously improved the surface energy and WF of gold electrodes by conducting oxygen plasma treatment to achieve high-performance OFET based on solution-processed organic single crystals. We cultivated a thin layer of gold oxide on Au electrodes to increase the WF by ∼0.7 eV. The surface energy of Au electrodes was enhanced to the same as AlOx dielectric surface, enabling the seamless growth of large-area C8-BTBT (2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene) organic single-crystal thin films via solution shearing. This technique facilitates the production of high-performance OFETs with the highest carrier mobility of 6.7 cm2 V-1 s-1 and sharp switching characterized by a subthreshold swing of 63.6 mV dec-1. The bottom-contact OFETs exhibited a lower contact resistance of 1.19 kΩ cm than its F4-TCNQ-doped top-contact control device. This method offers a straightforward and effective strategy for producing high-quality single-crystal OFETs, which are potentially suitable for commercial applications.

Improving Inhalation Performance with Particle Agglomeration via Combining Mechanical Dry Coating and Ultrasonic Vibration

Agglomerate formulations for dry powder inhalation (DPI) formed with fine particles are versatile means for the highly efficient delivery of budesonide. However, uncontrolled agglomeration induces high deposition in the upper airway, causing local side effects due to high mechanical strength, worse deagglomeration, and poor fine-particle delivery. In the present study, fine lactose was mechanically dry-coated prior to particle agglomeration, and the agglomerates were then spheroidized via ultrasonic vibration to improve their aerosol performance. The results showed that the agglomerate produced with the surface-enriched hydrophobic magnesium stearate and ultrasonic vibration demonstrated improved aerosolization properties, benefiting from their lower mechanical strength, less interactive cohesive force, and improved fine powder dispersion behavior. After dispersion utilizing a Turbuhaler® with a pharmaceutical cascade impactor test, a fine particle fraction (FPF) of 71.1 ± 1.3% and an artificial throat deposition of 19.3 ± 0.4% were achieved, suggesting the potential to improve the therapeutic outcomes of budesonide with less localized infections of the mouth and pharynx.

Determination of Hydrophobic Dispersive Surface Free Energy of Activated Carbon Fibers Measured by Inverse Gas Chromatographic Technique

Activated carbon fibers (ACFs) as one of the most important porous carbon materials are widely used in many applications that involve rapid adsorption and low-pressure loss, including air purification, water treatment, and electrochemical applications. For designing such fibers for the adsorption bed in gas and aqueous phases, in-depth comprehension of the surface components is crucial. However, achieving reliable values remains a major challenge due to the high adsorption affinity of ACFs. To overcome this problem, we propose a novel approach to determine London dispersive components (γSL) of the surface free energy of ACFs by inverse gas chromatography (IGC) technique at an infinite dilution. Our data reveal the γSL values at 298 K for bare carbon fibers (CFs) and the ACFs to be 97 and 260-285 mJ·m^-2, respectively, which lie in the regime of secondary bonding of physical adsorption. Our analysis indicates that these are impacted by micropores and defects on the carbon surfaces. Comparing the γSL obtained by the traditional Gray's method, our method is concluded as the most accurate and reliable value for the hydrophobic dispersive surface component of porous carbonaceous materials. As such, it could serve as a valuable tool in designing interface engineering in adsorption-related applications.

Investigation of the Surface Properties of Hexagonal Boron Nitride and Boron Phosphate by Inverse Gas Chromatography at Infinite Dilution

The boron-based ceramics namely hexagonal boron nitride (h-BN) and boron phosphate (BPO4) were synthesized and characterized by Fourier transform infrared spectroscopy and X-ray diffraction analysis. The surface properties of h-BN and BPO4 were examined by inverse gas chromatography method. The dispersive surface energy and the acidic-basic character of h-BN, and BPO4 surfaces were estimated by the retention time with probes such as n-hexane, n-heptane, n-octane, n-nonane, n-decane, acetone, ethyl acetate, dichloromethane, chloroform and tetrahydrofuran at infinite dilution region. The dispersive surface free energies calculated using both Schultz and Dorris-Gray methods, decreased linearly with increasing temperature. The specific adsorption free energy and the specific adsorption enthalpy corresponding to acid-base surface interactions were determined. By correlating with the donor and acceptor numbers of the probes, the acidic and the basic parameters of the h-BN and BPO4 were calculated. The values obtained for and parameters indicated that h-BN has a basic character, whereas BPO4 has an acidic character.

Understanding the Interfacial Adhesion between Natural Silk and Polycaprolactone for Fabrication of Continuous Silk Biocomposites

The poor interfacial adhesion between silk fiber and polyester species remains a critical problem for the optimal mechanical performance of silk-reinforced polyester composites. Here, we investigated in quantitative terms the interfacial properties between natural silk fibers and polycaprolactone (PCL) at nano-, micro-, and macroscales and fabricated continuous silk-PCL composite filaments by melt extrusion and drawing processing of PCL melt at 100, 120, and 140 °C. Bombyx mori (Bm) silk, Antheraea pernyi (Ap) silk, and polyamide6 (PA6) fiber were compared to the composite with PCL. The Ap silk exhibited the highest surface energy, the best wettability, and the largest interfacial shear strength (IFSS) with PCL. The silk-PCL composite from the 120 °C melt processing displayed the highest tensile modulus, implying an optimal temperature for interfacial adhesion. The Raman imaging technique revealed in detail the nature of the physical fusion of the interface phase in these silk- and polyamide-reinforced PCL composites. This work is intended to lay a foundation for the design and processing of robust composites from continuous silk fibers and bioresorbable polyesters for potential structural biomaterials.

Fundamentals and utilization of solid/ liquid phase boundary interactions on functional surfaces

The affinity of macroscopic solid surfaces or dispersed nano- and bioparticles towards liquids plays a key role in many areas from fluid transport to interactions of the cells with phase boundaries. Forces between solid interfaces in water become especially important when the surface texture or particles are in the colloidal size range. Although, solid-liquid interactions are still prioritized subjects of materials science and therefore are extensively studied, the related literature still lacks in conclusive approaches, which involve as much information on fundamental aspects as on recent experimental findings related to influencing the wetting and other wetting-related properties and applications of different surfaces. The aim of this review is to fill this gap by shedding light on the mechanism-of-action and design principles of different, state-of-the-art functional macroscopic surfaces, ranging from self-cleaning, photoreactive or antimicrobial coatings to emulsion separation membranes, as these surfaces are gaining distinguished attention during the ongoing global environmental and epidemic crises. As there are increasing numbers of examples for stimulus-responsive surfaces and their interactions with liquids in the literature, as well, this overview also covers different external stimulus-responsive systems, regarding their mechanistic principles and application possibilities.

Quantitative Study on Solubility Parameters and Related Thermodynamic Parameters of PVA with Different Alcoholysis Degrees

In recent years, inverse gas chromatography (IGC) and molecular dynamics simulation methods have been used to characterize the solubility parameters and surface parameters of polymers, which can provide quantitative reference for the further study of the surface and interface compatibility of polymer components in the future. In this paper, the solubility parameters and surface parameters of two kinds of common alcoholysis, PVA88 and PVA99, are studied by using the IGC method. The accuracy of the solubility parameters obtained by the IGC experiment is verified by molecular dynamics simulation. On the basis of this, the influence of repeated units of polyvinyl alcohol (PVA) on solubility parameters is studied, so as to determine the appropriate chain length of the PVA for simulation verification calculation. The results show that the solubility parameters are not much different when the PVA chain length is 30 and above; the numerical trends of the solubility parameters of PVA88 and PVA99 at room temperature are the same as the results of molecular dynamics simulation; the dispersive surface energy γsd and the specific surface energy γssp are scattered with the temperature distribution and have a small dependence on temperature. On the whole, the surface energy of PVA99 with a higher alcoholysis degree is higher than that of PVA88 with a lower alcoholysis degree. The surface specific adsorption free energy (ΔGsp) indicates that both PVA88 and PVA99 are amphoteric meta-acid materials, and the acidity of PVA99 is stronger.

Evaluation of the surface properties of 4-(Decyloxy) benzoic acid liquid crystal and its use in structural isomer separation

The selectivity of 4-(Decyloxy) benzoic acid (DBA) liquid crystal in surface adsorption region (303.2–328.2 K) and thermodynamic region (423.2 – 433.2 K) was investigated by inverse gas chromatography at infinite dilution (IGC-ID). The selectivity parameters of the structural isomer series named butyl acetate, butyl alcohol, and amyl alcohol series were calculated for the DBA using IGC-ID technique. Additionally, the surface properties including dispersive surface energy (gS D), free energy (DGA S), enthalpy (DHA S), and acidity-basicity constants were calculated with net retention volumes obtained from IGC-ID experiment results. When the DHA S and DGA S are constants, DBA surface was found to be an acidic character (KD/KA @ 0.89).

Thermoplastic bio-nanocomposites: From measurement of fundamental properties to practical application

Although the discovery of plastic has revolutionized materials used in many industries and by consumers, their non-biodegradable nature has led to one of the greatest problems of our times: plastic waste in the environment. Bioplastics which are biobased and biodegradable, have been suggested as alternatives for their fossil based counterparts, but their properties often do not meet the requirements that standard plastics would, and are in clear need of improvement. One way to do so is by the addition of nanoparticles which, when homogeneously dispersed, have been reported to result in great improvements. However, in practice, homogenous distribution of nanoparticles is not that trivial due to their tendency to aggregate, also after addition to the polymer matrix. Although theoretical frameworks to prevent this process are available, we feel that the options explored in practice are often rather trial and error in nature. For that reason, we review the theories available, aiming to facilitate the design of the nanocomposites for a sustainable future. We first discuss thermodynamic frameworks which revolve around nanoparticle aggregation. To minimize nanoparticle aggregation, the nanoparticle and polymer can be selected in such a way that they have similar polar and dispersive surface energies. The second part is dedicated to nanocomposite processing, where kinetic effects act on the nanocomposite material therewith influencing its final morphology, although it is good to point out that other factors such as reaggregation also affect the final nanocomposite morphology. The third section is dedicated to how nanoparticles affect the polymer matrix to which they are added. We describe how interactions at an atomic scale, result in the formation of an interphasial region which ultimately leads to changed bulk material properties. From these three sections, we conclude that three parameters are often overlooked when designing nanocomposites, namely the surface energies of the nanoparticles and polymers, the aggregation bond energy or strength, and the interphase region. Therefore, in the fourth section we provide an overview of techniques to identify these three parameters. We finish with a summery and outlook for the design of bio nanocomposites, where we bring all insights from the previous four sections together.

Surface Characterization of Carbonaceous Materials Using Inverse Gas Chromatography: A Review

It is essential to understand the adsorption of guest molecules on carbon-based materials for both theoretical and practical reasons. It is crucial to analyze the surface properties of carbon-based materials with a wide range of applications (e.g., catalyst supports, hydrogen storage, sensors, adsorbents, separation media, etc.). Inverse gas chromatography (IGC) as a powerful and sensitive technique can be used to characterize the surface physicochemical properties (i.e., Brunauer-Emmett-Teller (BET) surface area, surface energy heterogeneity, heat of adsorption, specific interaction of adsorption, work of cohesion, glass transition temperatures, solubility, and so forth) of various types of materials such as powders, films, and fibers. In this review, the principles, common methods, and application of IGC are discussed. In addition, the examples of various experiments developed for the IGC to characterize the carbonaceous materials (such as carbon nanotubes, graphite, and activated carbon) are discussed.

Inverse gas chromatography in the examination of adhesion between tooth hard tissues and restorative dental materials

The adhesion is a crucial issue in the bonding of dental restorative materials to tooth hard tissues. A strong and durable bond between artificial and natural materials is responsible for the success of the restoration in the oral cavity; therefore it has to be thoroughly examined before new restorative material is introduced to the market and used clinically. Among all methods used to examine bonding strength, most of them require a large number of healthy teeth to be conducted. In this paper, the bond strength between tooth hard tissues (dentin and enamel) and an exemplary restorative composite was examined with the non-conventional method, i.e. inverse gas chromatography. Dentin and enamel from bovine teeth were separated and subjected to the standard preparation procedure using the 3-component etch-and-rinse commercial bonding system. Tissues, as well as commercial restorative composite, were examined using inverse gas chromatography. The work of adhesion between dentin/enamel and composite was calculated. Obtained results were compared with the values of shear bond strength of six configurations, i.e. etched dentin/enamel-composite, primed dentin/enamel-composite, and bonded dentin/enamel-composite. All obtained results proved that there is a correlation between the values describing bond strength obtained from inverse gas chromatography and direct mechanical tests (shear bond strength tests). It proves that inverse gas chromatography is a powerful perspective tool for the examination of bond strength between tooth hard tissues and potential dental materials without using a large number of health tooth tissues.

Surface Thermo-Dynamic Characterization of Poly (Vinylidene Chloride-Co-Acrylonitrile) (P(VDC-co-AN)) Using Inverse-Gas Chromatography and Investigation of Visual Traits Using Computer Vision Image Processing Algorithms

The Inverse Gas Chromatography (IGC) technique has been employed for the surface thermo-dynamic characterization of the polymer Poly(vinylidene chloride-co-acrylonitrile) (P(VDC-co-AN)) in its pure form. IGC attributes, such as London dispersive surface energy, Gibbs free energy, and Guttman Lewis acid-base parameters were analyzed for the polymer (P(VDC-co-AN)). The London dispersive surface free energy (γSL) was calculated using the Schultz and Dorris–Gray method. The maximum surface energy value of (P(VDC-co-AN )) is found to be 29.93 mJ·m−2 and 24.15 mJ·m−2 in both methods respectively. In our analysis, it is observed that the γSL values decline linearly with an increase in temperature. The Guttman–Lewis acid-base parameter Ka,Kb values were estimated to be 0.13 and 0.49. Additionally, the surface character S value and the correlation coefficient were estimated to be 3.77 and 0.98 respectively. After the thermo-dynamic surface characterization, the (P(VDC-co-AN)) polymer overall surface character is found to be basic. The substantial results revealed that the (P(VDC-co-AN)) polymer surface contains more basic sites than acidic sites and, hence, can closely associate in acidic media. Additionally, visual traits of the polymer (P(VDC-co-AN)) were investigated by employing Computer Vision and Image Processing (CVIP) techniques on Scanning Electron Microscopy (SEM) images captured at resolutions ×50, ×200 and ×500. Several visual traits, such as intricate patterns, surface morphology, texture/roughness, particle area distribution (DA), directionality (DP), mean average particle area (μavg) and mean average particle standard deviation (σavg), were investigated on the polymer’s purest form. This collective study facilitates the researches to explore the pure form of the polymer Poly(vinylidene chloride-co-acrylonitrile) (P(VDC-co-AN )) in both chemical and visual perspective.

Surface termination of MgB2 unveiled by a combination of adsorption experiments and theoretical calculations

Superconductivity in polycrystalline and thin-film MgB2 is strongly affected by the termination of its surface, but a reliable determination of the surface termination is still a challenging task of surface chemistry. Here, the surface properties of superconducting MgB2 were investigated using a combination of inverse gas chromatography and van der Waals corrected density functional theory calculations. The dispersive surface energy was measured as a function of the surface coverage and its value (58 mJ m-2 to 48 mJ m-2) was verified by high-level non-local EXX + RPA calculations, which predicted that the dispersive contribution to the cleavage energy was 56 mJ m-2. The isosteric adsorption enthalpies of cyclohexane, dioxane, acetone and acetonitrile molecules were measured on an MgB2 sample and compared to the DFT calculated enthalpies for the Mg-terminated MgB2, B-terminated MgB2 and MgO(001) surfaces. The close agreement between theory and experiment for the Mg-terminated surface suggested that the magnesium termination is the dominant surface phase of MgB2. Thus, combining inverse gas chromatography experiments with theoretical calculations may provide information about the surface termination.

Role of the puckered anisotropic surface in the surface and adsorption properties of black phosphorus

Nanomaterials have a high surface-to-mass ratio and their surface properties significantly affect their features and application potential. Phosphorene, a single layer of black phosphorus (BP), was the first homoatomic two-dimensional material to be prepared after the discovery of graphene. The structure of phosphorene resembles the honeycomb arrangement of graphene, but its layers are buckled and highly anisotropic. We studied how this difference affects the surface properties of BP, namely the free surface energy and adsorption affinity of various organic molecules. Using inverse gas chromatography, we measured the total surface free energy of BP powder to be 90 mJ m-2 and showed that it was dominantly determined by dispersion forces, but, unlike on graphene, with a notable contribution from specific acid-base interactions. We further measured adsorption enthalpies of volatile organic compounds on BP and rationalized them using density functional theory calculations. Polar molecules showed an increased affinity due to a significant contribution of dipole-dipole interactions to the molecule-surface bonding, because the buckled surface of BP causes higher diffusion barriers than those on graphene, hinders molecular in-plane motion and supports mutual orientation of molecular dipoles over longer distances, in contrast to graphene.

Determination of the surface properties of kaolinite by inverse gas chromatography

Inverse gas chromatography (IGC) was applied to characterize the surface of kaolinite. The adsorption thermodynamic parameters (the standard enthalpy (∆H⁰), entropy (∆S⁰) and free energy of adsorption (∆G⁰), the dispersive component of the surface energy (γ_s^d), and the acid/base character of kaolinite surface were estimated by using the retention time of different non-polar and polar probes at infinite dilution region. The specific free energy of adsorption (∆G^sp), the specific enthalpy of adsorption (∆H^sp), and the specific entropy of adsorption (∆S^sp) of polar probes on kaolinite were determined. (∆G^sp) values were correlated with the donor and modified acceptor numbers of the probes to quantify the acidic (K_A) and the basic (K_D) parameters of the kaolinite surface. The values obtained for the parameters K_A and K_D indicated a basic character for kaolinite surface.

Surface properties of MoS2 probed by inverse gas chromatography and their impact on electrocatalytic properties

Layered transition metal dichalcogenides (TMDs) are at the forefront of materials research. One of the most important applications of these materials is their electrocatalytic activity towards hydrogen evolution, and these materials are suggested to replace scarce platinum. Whilst there are significant efforts towards this goal, there are various reports of electrocatalysis of MoS₂ (which is the most commonly tested TMD) with large variations of the reported electrocatalytic effect of the material, with overpotential varying by several hundreds of millivolts. Here, we analyzed surface properties of various bulk as well as single layer MoS₂ samples using inverse gas chromatography. All samples displayed significant variations in surface energies and their heterogeneities. The surface energy ranged from 50 to 120 mJ m^-2 depending on the sample and surface coverage. We correlated the surface properties and previously reported structural features of MoS₂ with their electrochemical activities. We concluded that the observed differences in electrochemistry are caused by the surface properties. This is an important finding with an enormous impact on the whole field of electrocatalysis of layered materials.

Effects of crystal habit on the sticking propensity of ibuprofen-A case study

This study demonstrates the effect of active pharmaceutical ingredient (API) particle habit on the sticking propensity of ibuprofen. Four diverse crystal habits with similar physico chemical properties are reported and the sticking propensity was found to increase with shape regularity. The surface energy of the extreme habits were shown to be different where particles that were more regular in shape exhibited surface energies of 9mJ/m² higher than those that were needle-like in habit. Computational and experimental data reveals that the increase in surface energy of the regular shaped particles can be attributed to the increase in the specific (polar) component, which is due to greater presence of faces which contain the carboxylic acid functionality at the surface. The increase in the specific energy component is shown to correlate with the sticking propensity of ibuprofen. It is proposed that investigation of the chemical causality of sticking, for this API and others, using the techniques demonstrated in this paper will be of increasing importance.

Particle engineering in pharmaceutical solids processing: surface energy considerations

During the past 10 years particle engineering in the pharmaceutical industry has become a topic of increasing importance. Engineers and pharmacists need to understand and control a range of key unit manufacturing operations such as milling, granulation, crystallisation, powder mixing and dry powder inhaled drugs which can be very challenging. It has now become very clear that in many of these particle processing operations, the surface energy of the starting, intermediate or final products is a key factor in understanding the processing operation and or the final product performance. This review will consider the surface energy and surface energy heterogeneity of crystalline solids, methods for the measurement of surface energy, effects of milling on powder surface energy, adhesion and cohesion on powder mixtures, crystal habits and surface energy, surface energy and powder granulation processes, performance of DPI systems and finally crystallisation conditions and surface energy. This review will conclude that the importance of surface energy as a significant factor in understanding the performance of many particulate pharmaceutical products and processes has now been clearly established. It is still nevertheless, work in progress both in terms of development of methods and establishing the limits for when surface energy is the key variable of relevance.

An equation to calculate the actual methylene middle parameter as a function of temperature

Methylene middle parameter [Formula: see text] , the product of the methylene group's cross-sectional area ( [Formula: see text] ) and the root square of its dispersive free energy ( [Formula: see text] ), is the key parameter to calculate the dispersive surface components of solids (γs(d)) using inverse gas chromatography (IGC) at different temperatures. The only method reported to calculate [Formula: see text] as a function of temperature is the Dorris-Gray method. However, the conventional values of [Formula: see text] calculated by the Dorris-Gray method depend heavily on theoretical aspects. This paper establishes a novel equation calculating the actual [Formula: see text] as a function of temperature using the latest and most accurate surface parameters of seven successive n-alkanes. The obtained actual [Formula: see text] values are slightly higher those of the conventional [Formula: see text] . At 20°C, the actual [Formula: see text] generates γs(d) values less than those generated using the conventional [Formula: see text] by ∼3%, and this reduction in calculated γs(d) values increases linearly to become ∼5% at 100°C. Therefore, using the new actual [Formula: see text] seems to mitigate the discrepancy between the γs(d) values measured by IGC and those measured by the contact angle method.

Inverse gas chromatography applications: a review

Inverse gas chromatography (IGC) is a versatile, powerful, sensitive and relatively fast technique for characterizing the physicochemical properties of materials. Due to its applicability in determining surface properties of solids in any form such as films, fibres and powders of both crystalline and amorphous structures, IGC became a popular technique for surface characterization, used extensively soon after its development. One of the most appealing features of IGC that led to its popularity among analytical scientists in early years was its similarity in principle to analytical gas chromatography (GC). The main aspect which distinguishes IGC experiments from conventional GC is the role of mobile and stationary phases. Contrary to conventional GC, the material under investigation is placed in the chromatographic column and a known probe vapour is used to provide information on the surface. In this review, information concerning the history, instrumentation and applications is discussed. Examples of the many experiments developed for IGC method are selected and described. Materials that have been analysed include polymers, pharmaceuticals, minerals, surfactants, and nanomaterials. The properties that can be determined using the IGC technique include enthalpy and entropy of sorption, surface energy (dispersive and specific components), work of co/adhesion, miscibility and solubility parameters, surface heterogeneity, glass transition temperature, and specific surface area.

A new method to determine dispersive surface energy site distributions by inverse gas chromatography

A computational model to predict the relative energy site contributions of a heterogeneous material from data collected by finite dilution-inverse gas chromatography (FD-IGC) is presented in this work. The methodology employed a multisolvent system site filling model utilizing Boltzmann statistics, expanding on previous efforts to calculate "experienced energies" at varying coverage, yielding a retention volume distribution allowing calculation of a surface free energy distribution. Surface free energy distributions were experimentally measured for racemic ibuprofen and β-mannitol powders, the energies of each were found in the ranges 43-52 and 40-55 mJ/m(2), respectively, over a surface coverage range of 0-8%. The computed contributions to surface energy values were found to match closely with data collected on macroscopic crystals by alternative techniques (±<1.5 mJ/m(2)).