Recent development and applications of dispersive liquid–liquid microextraction

Determination of toxic α-dicarbonyl compounds in sesame oils using dispersive liquid-liquid microextraction coupled with gas chromatography-mass spectrometry

Glyoxal, methylglyoxal, and diacetyl are toxic α-dicarbonyl compounds found in heat-processed foods, including edible oils. Dispersive liquid-liquid microextraction was combined with gas chromatography mass spectrometry to determine the glyoxal, methylglyoxal, and diacetyl contents in sesame oil. Chloroform and methanol were selected as the optimal extraction and dispersive solvents, respectively. The maximum derivatization efficiency was obtained using 500 µg of the derivatization agent, o-phenylenediamine. The derivatization of glyoxal was completed in 1 h, whereas those of methylglyoxal and diacetyl were completed immediately. The optimized method was validated, and was found to exhibit a good linearity, recovery, intraday repeatability, and interday reproducibility. The α-dicarbonyl compound concentrations in the oils were dependent on the roasting temperature. The sesame oil concentrates contained 0-175.4, 0-990.5, and 0-220.9 ng g-1 of glyoxal, methylglyoxal, and diacetyl, respectively. For the perilla oils, the respective concentrations were 0-96.4, 0-410.8, and 0-197.5 ng g-1.

Acid induced dispersive liquid-liquid microextraction based on in situ formation of hydrophobic deep eutectic solvents for the extraction of bisphenol A and alkylphenols in water and beverage samples

This study describes the development of an acid induced dispersive liquid-liquid microextraction method based on the in situ formation of hydrophobic deep eutectic solvents for the extraction of bisphenol A and alkylphenols from environmental water and beverage samples. Hydrochloric acid altered the hydrophilic-hydrophobic state of fatty acid salts to obtain hydrophobic fatty acids, which formed hydrophobic deep eutectic solvents with analytes in situ to extract the analytes. Under optimized conditions, the limits of detection and limits of quantitation were 0.03-0.1 μg L-1 and 0.12-0.3 μg L-1, the intraday and interday relative standard deviations were less than 3.9 %, and the enrichment factor was 29-32. The recoveries of bisphenol A and alkylphenols were 95.9-104.9 % and 86.9-105.0 %, respectively. The extraction process used only hydrochloric acid and fatty acid salts, and the extraction process required less than 1 min. This method has the advantages of simplicity, speed, low cost and environmental friendliness.

A fast method for the determination of personal care product chemicals in human urine using dispersive liquid-liquid extraction and ultra high-performance liquid chromatography-tandem mass spectrometry

RATIONALE

Personal care product chemicals (PCPCs) are the chemicals used in personal care products. Many of them are endocrine disruptors and have potential adverse effects on humans. The concentrations of PCPCs in urine are the main biomarker for assessing human exposure.

METHODS

A method was developed for the simultaneous determination of 14 PCPCs in human urine using dispersive liquid-liquid extraction combined with ultra high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS).

RESULTS

Compared with liquid-liquid extraction, this method had the advantages of time efficiency, sensitivity, and limited organic solvent consumption. It produced good linearity (0.9965-0.9996), limits of detection (2.82-36.36 pg mL-1 ), limits of quantitation (9.39-121.08 pg mL-1 ), matrix effect (-0.90%-2.55%), intra-day precision (relative standard deviations [RSDs] <15%), and inter-day precision (RSDs <19.9%). The method had satisfactory relative recovery at three concentration levels.

CONCLUSIONS

A rapid method was developed for the simultaneous quantification of 14 PCPCs in human urine. The practicability of the method was verified with 21 urine from university students. It is expected that this method will provide a powerful reference for the assessment of exposure to PCPCs in large populations.

Development of a generic sample preparation method using dispersive liquid-liquid microextraction for the monitoring of leachable compounds in hospital pharmacy-prepared prefilled drug products

Performant sample preparation is mandatory in any leachable study to clean and preconcentrate analytes within the sample to offer the best possible extraction recovery as well the best precision for any given substance. The aim consists in developing a sample preparation method for hospital pharmacy-prepared drug products such as long-term storage prefilled syringes, vials and IV bags for the screening of leachable compounds. The Quality Control Laboratory of the Pharmacy of the Lausanne University Hospital (Switzerland) has developed a time- and cost-effective, highly sensitive, robust, and fast method using liquid chromatography coupled with high-resolution mass spectrometry (LC-HRMS) for the analysis of 205 plastic additives. An innovative setup, based on postcolumn infusion (PCI) using 2% ammonium hydroxide in methanol was used to boost the signal intensity of the analytes in MS detection. A database for extractable and leachable trace assessment (DELTA) was built to assist in the screening process of 205 plastic packaging-related compounds. The development of the sample preparation was based on 33 plastic additive candidates in different hospital pharmacy compounding solutions, and their extraction recovery rates as well as their relative standard deviation were taken into consideration. In conclusion, the developed DLLME was assigned with ultrasound assistance and triple extraction, which brought about extraction recovery rates between 67% and 92%, a good RSD <10%, and a preconcentration factor of 50×. Therefore, DLLME could be considered suitable for the semiquantitative screening of leachable additives in simple hospital pharmacy-prepared prefilled drug products.

Inside the History of Italian Coloring Industries: An Investigation of ACNA Dyes through a Novel Analytical Protocol for Synthetic Dye Extraction and Characterization

The introduction of synthetic dyes completely changed the industrial production and use of colorants for art materials. From the synthesis of the first synthetic dye, mauveine, in 1856 until today, artists have enjoyed a wider range of colors and selection of chemical properties than was ever available before. However, the introduction of synthetic dyes introduced a wider variety and increased the complexity of the chemical structures of marketed dyes. This work looks towards the analysis of synthetically dyed objects in heritage collections, applying an extraction protocol based on the use of ammonia, which is considered favorable for natural anthraquinone dyes but has never before been applied to acid synthetic dyes. This work also presents an innovative cleanup step based on the use of an ion pair dispersive liquid-liquid microextraction for the purification and preconcentration of historical synthetic dyes before analysis. This approach was adapted from food science analysis and is applied to synthetic dyes in heritage science for the first time in this paper. The results showed adequate recovery of analytes and allowed for the ammonia-based extraction method to be applied successfully to 15 samples of suspected azo dyes from the Azienda Coloranti Nazionali e Affini (ACNA) synthetic dye collection, identified through untargeted HPLC-HRMS analyses.

Arsenic speciation by using emerging sample preparation techniques: a review

Arsenic is a hazardous element that causes environmental pollution. Due to its toxicological effects, it is crucial to quantify and minimize the hazardous impact on the ecology. Despite the significant advances in analytical techniques, sample preparation is still crucial for determining target analytes in complex matrices. Several factors affect the direct analysis, such as trace-level analysis, advanced regulatory requirements, complexity of sample matrices, and incompatible with analytical instrumentation. Along with the development in the sample preparation process, microextraction methods play an essential role in the sample preparation process. Microextraction techniques (METs) are the newest green approach that replaces traditional sample preparation and preconcentration methods. METs have minimized the limitation of conventional sample preparation methods while keeping all their benefits. METs improve extraction efficacy, are fast, automated, use less amount of solvents, and are suitable for the environment. Microextraction techniques with less solvent consumption, such as solid phase microextraction (SPME) solvent-free methods, and liquid phase microextraction (LPME), are widely used in modern analytical procedures. SPME development focuses on synthesizing new sorbents and applying online sample preparation, whereas LPME research investigates the utilization of new solvents.

Profiling Docetaxel in Plasma and Urine Samples from a Pediatric Cancer Patient Using Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction Combined with LC-MS/MS

In recent years, therapeutic drug monitoring (TDM) has been applied in docetaxel (DOC)-based anticancer therapy to precisely control various pharmacokinetic parameters, including the concentration of DOC in biofluids (e.g., plasma or urine), its clearance, and its area under the curve (AUC). The ability to determine these values and to monitor DOC levels in biological samples depends on the availability of precise and accurate analytical methods that both enable fast and sensitive analysis and can be implemented in routine clinical practice. This paper presents a new method for isolating DOC from plasma and urine samples based on the coupling of microextraction and advanced liquid chromatography with tandem mass spectrometry (LC-MS/MS). In the proposed method, biological samples are prepared via ultrasound-assisted dispersive liquid-liquid microextraction (UA-DLLME) using ethanol (EtOH) and chloroform (Chl) as the desorption and extraction solvents, respectively. The proposed protocol was fully validated according to the Food and Drug Administration (FDA) and the International Council for Harmonization of Technical Requirements for Pharmaceuticals for Human Use (ICH) requirements. The developed method was then applied to monitor the DOC profile in plasma and urine samples collected from a pediatric patient suffering from cardiac angiosarcoma (AS) with metastasis to lungs and mediastinal lymph nodes, who was receiving treatment with DOC at a dose of 30 mg/m² body surface area. Due to the rarity of this disease, TDM was carried out to determine the exact levels of DOC at particular time points to ascertain which levels were conducive to maximizing the treatment's effectiveness while minimizing the drug's toxicity. To this end, the concentration-time profiles of DOC in the plasma and urine samples were determined, and the levels of DOC at specific time intervals up to 3 days after administration were measured. The results showed that DOC was present at higher concentrations in the plasma than in the urine samples, which is due to the fact that this drug is primarily metabolized in the liver and then eliminated with the bile. The obtained data provided information about the pharmacokinetic profile of DOC in pediatric patients with cardiac AS, which enabled the dose to be adjusted to achieve the optimal therapeutic regimen. The findings of this work demonstrate that the optimized method can be applied for the routine monitoring of DOC levels in plasma and urine samples as a part of pharmacotherapy in oncological patients.

Sustainable dispersive liquid-liquid microextraction method utilizing a natural deep eutectic solvent for determination of chloramphenicol in honey: assessment of the environmental impact of the developed method

The greening of pharmaceutical analysis is gaining interest, and different approaches have been proposed, such as minimizing the consumption of hazardous reagents, replacing toxic solvents with safer alternatives, and reducing waste generation. In this work, a natural deep eutectic solvent (NADES) was synthesized and utilized as a green alternative in dispersive liquid-liquid microextraction (DLLME) for the determination of chloramphenicol in honey. Different deep eutectic solvents composed of monoterpenoids and acids were tested. The NADES system composed of menthol and acetic acid at a molar ratio of 1 : 1 was found to be the most appropriate in terms of extraction recovery. Different DLLME parameters including vortex time, centrifugation time, sample volume, and deep eutectic solvent volume were optimized. A determination coefficient of 0.9997 was achieved. Satisfactory recovery ranged from 98.8 to 101.5 with % RSD ≤4.5. The chromatographic performance of the presented method compared with other previously documented methods for determination of chloramphenicol in honey was highlighted. Additionally, the ecological impact of the developed method was assessed employing three tools: the Analytical Eco-scale, the Green Analytical Procedure Index, and the Analytical GREEnness metric. The presented method can be regarded as a green substitute for the traditional methods used for the determination of chloramphenicol in honey.

Sponge-nested polymer monolith sorptive extraction

Polymer monoliths are an alternative to traditional particle-packed supports used in solid-phase extraction because of their ease of preparation, high porosity, and pH stability. They often required the attachment of monoliths to a support, such as the internal walls of a column to enable their use for sample preparation. Applications of free-standing polymer monoliths are rarely found because of their limited mechanical stability. Herein, divinylbenzene monoliths were polymerised within a commercial melamine-formaldehyde sponge using different polymerisation times. The sponge-nested polymer monoliths are highly robust, and their size and shape can be easily adjusted for desired applications. The prepared sponge-nested polymer monoliths had surface areas in the range of 237 m² g^-1 to 369 m² g^-1. A melamine-formaldehyde sponge cut into 1 cm³ cubes were used to template the polymer monoliths. Miniaturized monoliths with a size of 0.125 cm³ were directly cut from the larger cubes without compromising the integrity of the porous monolith structure. The resulting nested monolith sorptive extraction (NMSE) supports were applied for the extraction of the endocrine disruptors bisphenol A, 4-tert-butylphenol, and 4-tert-octylphenol. The prepared sponge-nested monoliths are low-cost (40 monoliths/AU$). NMSE was carried out by the direct immersion of the monoliths in the aqueous standards/samples, requiring only an orbital shaker for the extraction procedure. Best performance was obtained for polymer monoliths polymerized for 6 h, enabling limits of detection of 5.6 to 6.5 µg L^-1 for the selected analysis using HPLC-UV.

Research Advances in the Analysis of Estrogenic Endocrine Disrupting Compounds in Milk and Dairy Products

Milk and dairy products are sources of exposure to estrogenic endocrine disrupting compounds (e-EDCs). Estrogenic disruptors can accumulate in organisms through the food chain and may negatively affect ecosystems and organisms even at low concentrations. Therefore, the analysis of e-EDCs in dairy products is of practical significance. Continuous efforts have been made to establish effective methods to detect e-EDCs, using convenient sample pretreatments and simple steps. This review aims to summarize the recently reported pretreatment methods for estrogenic disruptors, such as solid-phase extraction (SPE) and liquid phase microextraction (LPME), determination methods including gas chromatography-mass spectrometry (GC-MS), liquid chromatography-mass spectrometry (LC-MS), Raman spectroscopy, and biosensors, to provide a reliable theoretical basis and operational method for e-EDC analysis in the future.

Vinegar Volatile Organic Compounds: Analytical Methods, Constituents, and Formation Processes

Vinegar is an acid condiment shared all over the world. According to the raw materials, vinegar can be mainly divided into fruit and cereal ones, both of which possess unique aroma and flavor characteristics and corresponding volatile organic compounds (VOCs). Many studies about vinegar VOCs' (VVOCs) sorts, analytical methods, and forming mechanisms have been done. In this review, the main categories of vinegar and their distribution in the world are briefly introduced, then VVOCs' analytical and identified methods, types, and forming processes are summarized. Additionally, the VVOCs' research directions are discussed and prospected. According to the searched literatures, this study is the first to systematically review the analytical methods, sorts, and formation mechanisms of VVOCs, which will make the readers better understand the vinegar's aromas and flavors and their producing mechanisms.

Methodology for Determining Phthalate Residues by Ultrasound–Vortex-Assisted Dispersive Liquid–Liquid Microextraction and GC-IT/MS in Hot Drink Samples by Vending Machines

In this study, a simple, fast, and effective methodology has been developed for the detection and quantification of seven phthalates potentially released in hot drinks from disposable containers used in vending machines. The authors determined the optimal conditions to be applied during the various steps of extraction of seven phthalates (DMP, DEP, DBP, DiBP, DEHP, DNOP, and DDP) from hot beverages using a model solution. The extraction and preconcentration technique used was ultrasound–vortex-assisted dispersive liquid–liquid microextraction (UVA-DLLME) followed by gas chromatographic analysis obtaining recoveries from 66.7% to 101.2% with precision and reproducibility <6.3% and <11.1%, respectively. The influence of waiting time, from the dispensing of the drink to its actual consumption, for the extraction of molecules was investigated, obtaining a temporal release profile slightly shifted towards the PAEs with higher molecular weight and vice versa for those with low molecular weight. In addition, the best instrumental parameters to be applied during the analysis of the extracts obtained were established. This optimization was carried out using GC-FID, whereas the analysis of real samples was carried out by means of GC-IT/MS for ultra-trace analysis purposes; limits of detection (LODs) ranging between 0.8 ng mL−1 and 15.4 ng mL−1 and limits of quantification (LOQs) from 1.6 ng mL−1 to 35.8 ng mL−1, both of them lower than those found by FID, were obtained.

A simple, environmental-friendly and reliable d-SPE method using amino-containing metal-organic framework MIL-125-NH2 to determine pesticide residues in pomelo samples from different localities

A simple, environmentally-friendly and reliable method was developed to simultaneously monitor the residue of methyl 1-naphthalene acetate, parathion-methyl, fenitrothion, bromophos and phenthoate in pomelo by using dispersive solid-phase extraction technique (d-SPE). In this method, these target analytes were captured by MIL-125-NH₂ and detected by GC-MS/MS. The key parameters of d-SPE were optimized by the single factor experiment. Under the optimized conditions, a good determination coefficient (R² > 0.9922) and extraction recoveries (64.7-116.8%) are obtained. The limit of detections (0.03-1.07 ng/g) is lower than the MRLs in citrus fruits established by EU (10-15000 ng/g) and China (10-10000 ng/g). The precisions of intra-day and inter-day are 1.3-8.9% and 3.8-14.9%, respectively. In addition, the sorbent MIL-125-NH₂ is stable and can be reused at least eight times. These results prove the established method is efficient and reliable to detect the pesticide residues in pomelo.

Dispersive liquid-liquid microextraction of Cd, Hg and Pb from medicines prior to ICP OES determination according to the United States Pharmacopeia

A simple, sensitive and matrix-effect free analytical method for simultaneous determination of Cd, Hg and Pb in drug samples (i.e., commercial dosage tablets) by inductively coupled plasma optical emission spectrometry (ICP OES) has been developed. According to the United States Pharmacopeia (USP) Chapter 232, those metals are considered elemental impurities from class 1 and they must be assessed in pharmaceutical production as well as in quality control evaluation. In order to increase the sensitivity of the analysis, dispersive liquid-liquid microextraction (DLLME) was performed and seven factors affecting analyte extraction were optimized by multivariate analysis. A microvolume of analyte enriched phase was directly introduced into the plasma using a multi-nebulizer, providing a high enrichment factor. When compared to conventional ICP OES analysis, DLLME improves the limit of quantitation (LOQ) values on average 40-fold for all analytes. Consequently, LOQ values were significantly lower than their permissible daily exposure limits for oral drugs. Accuracy was evaluated by addition and recovery experiments following USP recommendations in eight commercial drug samples. Recovery and RSD values were within the range of 90-108% and 1-9%, respectively.

Comparison of Two Extraction Procedures, SPE and DLLME, for Determining Plasticizer Residues in Hot Drinks at Vending Machines

This paper would like to compare two extraction procedures for analyzing phthalates (PAEs) in hot drinks collected at vending machines, usually coffee and tea. The two analytical procedures are based on Solid Phase Extraction (SPE) using C18 cartridge and on dispersive liquid-liquid microextraction (DLLME) assisted by ultrasound and vortex for improving the dispersion mechanically, with each followed by a routinary analytical method such as GC-FID. Seven phthalates (DMP, DEP, DiBP, DBP, DEHP, DOP, DDP) have been analyzed and determined. All the analytical parameters (i.e., recovery, limit of detection, limit of quantification, enrichment factors, repeatability, reproducibility) have been investigated and discussed, as has the matrix effect. The entire procedure has been applied to hot drink matrices, e.g., coffee, decaffeinated coffee, barley coffee, ginseng coffee and tea.

Multiclass Pesticide Residue Analysis in Fruit and Vegetable Samples by Combining Acetone-Based Salting-Out Assisted Extraction with Dispersive Liquid-Liquid Microextraction

Isolation and enrichment of multiclass pesticides’ residue, namely, fungicides (benalaxyl), herbicides (atrazine), carbamate insecticides (carbofuran), organophosphate insecticides (chlorpyrifos), organochlorine insecticides (4,4′-DDT), and pyrethroid insecticides (bifenthrin), were made by combining acetone-based salting-out assisted extraction with the dispersive liquid-liquid microextraction (SADLLME) method, followed by high-performance liquid chromatography-diode array detection (HPLC-DAD). The effect of the type and volume of the extraction solvent in the pretreatment step, the volume of the disperser solvent (acetone extract), the type and volume of the extraction solvent, pH, and salt addition in the DLLME procedure was studied. Good coefficient of determination (R2 ≥ 0.9964) was obtained for all the target analytes. The limits of detection and quantification limits were between 2.1 and 4.5 and 5.7 and 12.9 µg/kg, respectively, with adequate enrichment factors ranging from 37.6 to 191. The recoveries of spiked blank tomato ranged from 86.8 to 109.5%. The limit of quantification of the proposed method was lower than the maximum residue limits set by the European Union. The repeatability and reproducibility of precisions ranged between 2.9 and 8.0 and 4.9 and 9.5%, respectively. The optimized and validated method was applied to quantify pesticides in tomato, pear, apple, and melon obtained from different markets. However, all target compounds studied in this work were not detected in any real samples applied. Overall, the work results revealed that the proposed method is useful for the sample extraction and preconcentration of the target analytes from fruits and vegetables.

Essential oil-based dispersive liquid-liquid microextraction for the determination of N,N-dimethyltryptamine and β-carbolines in human plasma: A novel solvent-free alternative

The present study describes the development of a novel solvent-free vortex-assisted dispersive liquid-liquid microextraction alternative based on a natural essential oil as extracting solvent (VA-EO-DLLME) for the determination of N,N-dimethyltryptamine (DMT), harmine (HRM), harmaline (HRL) and tetrahydroarmine (THH) (compounds found in the ayahuasca tea, a psychedelic plant preparation) in human plasma. After optimization through full factorial and Box-Behnken experimental designs, this VA-EO-DLLME followed by ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) was completely validated and applied to authentic plasma specimens. Sample preparation consisted in the addition of 60 mg of NaCl, 100 μL of borate buffer and 100 μL of Eucalyptus globulus essential oil to a 200 μL aliquot of human plasma. After 30 s of vortex agitation followed by 5 min of centrifugation (10,000 rpm), 80 μL of the oil supernatant was dried and resuspended in mobile phase prior to injection into the UHPLC-MS/MS system. Once optimized, the validated method yielded LoDs ≤1.0 ng mL^-1 for all analytes. LoQ was 1.0 ng mL^-1 for DMT, HRL and HRM and 2.0 ng mL^-1 for THH. The method has shown to be linear over the range of LoQ up to 150 ng mL^-1 (r² ≥ 0.9926). Intra/inter-day precision and accuracy met the acceptance criteria at three quality control (QC) levels. An additional intermediate precision study demonstrated that, except for THH and HRL at low and medium QCs, the overall method performance was similar for the three different oil sources. Matrix effect evaluation showed predominant ion suppression, ranging from 56% to 83%. Recovery varied from 33 up to 101% with an average of 50 ± 15.8%. Selectivity studies showed no interferences. Analysis of 13 authentic samples proved method feasibility. Finally, we believe that our novel VA-EO-DLLME approach offers a very simple, fast, cost-effective and eco-friendly alternative based on the use of an easily accessible and entirely green material as an extracting solvent. This may represent an incentive for researchers to investigate novel and creative alternatives, such as essential oils, as substitutes of organic solvents for microextraction methods in forensic and clinical contexts.

DLLME-SFO-GC-MS procedure for the determination of 10 organochlorine pesticides in water and remediation using magnetite nanoparticles

There exists a high demand for fast, simple, and reliable methodologies for determining the presence of organochlorine pesticides (OCPs) on environmental samples. Moreover, the toxicity and accumulation of potential OCPs in several environments have led to the development of technologies that achieve their removal from contaminated waters. In this study, a novel method combining a dispersive liquid-liquid microextraction procedure based on the solidification of floating organic drop is developed and validated for the extraction, preconcentration, and determination of 10 OCPs: α-BHC, p,p'-DDE, δ-BHC, dieldrin, p,p'-DDT, endosulfan I, endosulfan sulfate, heptachlor, heptachlor epoxide (isomer B), and methoxychlor in water samples. The results show that the calibration curves were linear for all the studied compounds, and the coefficients of correlation higher than 0.99. The variation coefficient for precision and accuracy was lower than 10%, and the accuracy ranged from 93 to 105%. Low limit of detection and limit of quantification values ranging from 0.06-3.00 ng mL^-1 and 0.20-10 ng mL^-1 were obtained, respectively. The capability of the proposed method was confirmed using an analysis of the water samples before and after the degradation process; this was achieved by employing nanomaterials, while performing an analysis of 160 real samples that were sourced from a Brazilian river. A cobalt-doped magnetite was applied for the environmental remediation of the studied compounds, and it was verified that the novel material has the potential to be used in environmental remediation with a degradation efficiency exceeding 80% for the majority of the studied compounds.

Deep-eutectic-solvent-based dispersive and emulsification liquid-liquid microextraction methods for the speciation of selenium in water and determining its total content levels in milk formula and cereals

Rapid and environmentally friendly ultrasound-assisted dispersive liquid-liquid microextraction (US-DLLμE) and vortex assisted-emulsification liquid-liquid microextraction (VA-ELLμE) methods are proposed for the speciation of selenium in domestic and mineral water samples. A deep eutectic solvent (DES) prepared with different ratios of choline chloride and phenol is used as an extractant for hydrophobic tetravalent Se complexed with diethyldithiocarbamate in different water samples. The total inorganic Se species levels in water samples were determined via reducing Se(vi) to Se(iv), using sodium thiosulphate as a reducing agent. The total Se levels in formula milk and cereal samples were determined after microwave acid digestion. The different heating steps in GFAAS were also optimized. The analytical parameters for US-DLLμE and VA-ELLμE, including pH, the volume of complexing agent, the ultrasound and vortex mixing shaking times, and the volume and composition of the deep eutectic solvent, were optimized. The accuracies of both methods were confirmed based on the analysis of a certified reference material (CRM) BCR 189 (wholemeal flour). The enhancement factor (EF) and limit of detection (LOD) for Se(iv) via US-DLLμE were found to be 90.8 and 0.029 μg L^-1, respectively, whereas an EF of 81.8 and LOD of 0.036 μg L^-1 were obtained via VA-ELLμE. The % relative standard deviation (%RSD) values obtained based on the analysis of six replicate standards under the optimized conditions for US-DLLμE and VA-ELLμE were found to be 4.2 and 5.8%, respectively. The optimized methods were applied to different drinking water samples, and acid-digested milk formula and baby cereal food samples.

Application of liquid-phase microextraction to the analysis of plant and herbal samples

INTRODUCTION

The analysis of plant and herbal samples is a challenging task for analytical chemists due to the complexity of the matrix combined with the low concentration of analytes. In recent years different liquid-phase microextraction (LPME) techniques coupled with a variety of analytical equipment have been developed for the determination of both organic and inorganic analytes.

OBJECTIVE

Over the past few years, the number of research papers in this field has shown a markedly growing tendency. Therefore, the purpose of this review paper is to summarise and critically evaluate research articles focused on the application of LPME techniques for the analysis of plant and herbal samples.

RESULTS

Due to the complex nature of the samples, the direct application of LPME techniques to the analysis of plants has not often been done. LPME techniques as well as their modalities have been commonly applied in combination with other pretreatment techniques, including a solid-liquid extraction technique supported by mechanical agitation or auxiliary energies for plant analysis. Applications and the most important parameters are summarised in the tables.

CONCLUSION

This review summarises the application of the LPME procedure and shows the major benefits of LPME, such as the low volume of solvents used, high enrichment factor, simplicity of operation and wide selection of applicable detection techniques. We can expect further development of microextraction analytical methods that focus on direct sample analysis with the application of green extraction solvents while fully automating procedures for the analysis of plant materials.

Continuous Flow Upgrading of Selected C2-C6 Platform Chemicals Derived from Biomass

The ever increasing industrial production of commodity and specialty chemicals inexorably depletes the finite primary fossil resources available on Earth. The forecast of population growth over the next 3 decades is a very strong incentive for the identification of alternative primary resources other than petro-based ones. In contrast with fossil resources, renewable biomass is a virtually inexhaustible reservoir of chemical building blocks. Shifting the current industrial paradigm from almost exclusively petro-based resources to alternative bio-based raw materials requires more than vibrant political messages; it requires a profound revision of the concepts and technologies on which industrial chemical processes rely. Only a small fraction of molecules extracted from biomass bears significant chemical and commercial potentials to be considered as ubiquitous chemical platforms upon which a new, bio-based industry can thrive. Owing to its inherent assets in terms of unique process experience, scalability, and reduced environmental footprint, flow chemistry arguably has a major role to play in this context. This review covers a selection of C₂ to C₆ bio-based chemical platforms with existing commercial markets including polyols (ethylene glycol, 1,2-propanediol, 1,3-propanediol, glycerol, 1,4-butanediol, xylitol, and sorbitol), furanoids (furfural and 5-hydroxymethylfurfural) and carboxylic acids (lactic acid, succinic acid, fumaric acid, malic acid, itaconic acid, and levulinic acid). The aim of this review is to illustrate the various aspects of upgrading bio-based platform molecules toward commodity or specialty chemicals using new process concepts that fall under the umbrella of continuous flow technology and that could change the future perspectives of biorefineries.

Analytical Scheme for Simultaneous Determination of Phthalates and Bisphenol A in Honey Samples Based on Dispersive Liquid-Liquid Microextraction Followed by GC-IT/MS. Effect of the Thermal Stress on PAE/BP-A Levels

In this paper, an analytical protocol was developed for the simultaneous determination of phthalates (di-methyl phthalate DMP, di-ethyl phthalate DEP, di-isobutyl phthalate DiBP, di-n-butyl phthalate DBP, bis-(2-ethylhexyl) phthalate DEHP, di-n-octyl phthalate DNOP) and bisphenol A (BPA). The extraction technique used was the ultrasound vortex assisted dispersive liquid–liquid microextraction (UVA-DLLME). The method involves analyte extraction using 75 µL of benzene and subsequent analysis by gas chromatography combined with ion trap mass spectrometry (GC-IT/MS). The method is sensitive, reliable, and reproducible with a limit of detection (LOD) below 13 ng g⁻¹ and limit of quantification (LOQ) below 22 ng g⁻¹ and the intra- and inter-day errors below 7.2 and 9.3, respectively. The method developed and validated was applied to six honey samples (i.e., four single-use commercial ones and two home-made ones. Some phthalates were found in the samples at concentrations below the specific migration limits (SMLs). Furthermore, the commercial samples were subjected to two different thermal stresses (24 h and 48 h at 40 °C) for evidence of the release of plastic from the containers. An increase in the phthalate concentrations was observed, especially during the first phase of the shock, but the levels were still within the limits of the regulations.

Preparation of porous aromatic framework modified graphene oxide for pipette-tip solid-phase extraction of theophylline in tea

A new material called as porous aromatic frameworks modified graphene oxide (PAFs-GO) was synthesized, and it was used as an adsorbent in pipette-tip SPE for the effective purification and enrichment of theophylline in tea sample by HPLC. The properties of PAFs-GO were characterized by field emission SEM, FTIR, thermogravimetry analysis and Brunauer Emmett Teller N₂ adsorption-desorption analysis. The results of static adsorption and dynamic adsorption test showed PAFs-GO had higher adsorption ability (93.25 mg/g) than graphene oxide. The LOD and LOQ of the method were 0.0141 and 0.0471 µg/mL, respectively. The acceptable method reproducibility was found as intra- and inter-day precisions, yielding the RSDs <4.62%. By introducing PAFs as support skeleton, the specific surface area of GO was effectively increased, and the penetrability was improved. Studies showed that the proposed method had been successfully applied for purification and enrichment of theophylline in complex tea matrix.

A Vortex-Assisted Dispersive Liquid-Liquid Microextraction Followed by UPLC-MS/MS for Simultaneous Determination of Pesticides and Aflatoxins in Herbal Tea

A method for detecting the organophosphorus pesticides residue and aflatoxins in China herbal tea has been developed by UPLC-MS/MS coupled with vortex-assisted dispersive liquid-liquid microextraction (DLLME). The extraction conditions for vortex-assisted DLLME extraction were optimized using single-factor experiments and response surface design. The optimum conditions for the experiment were the pH 5.1, 347 µL of chloroform (extraction solvent) and 1614 µL of acetonitrile (dispersive solvent). Under the optimum conditions, the targets were good linearity in the range of 0.1 µg/L⁻25 µg/L and the correlation coefficient above 0.9998. The mean recoveries of all analytes were in the ranged from 70.06%⁻115.65% with RSDs below 8.54%. The detection limits were in the range of 0.001 µg/L⁻0.01µg/L. The proposed method is a fast and effective sample preparation with good enrichment and extraction efficiency, which can simultaneously detect pesticides and aflatoxins in China herbal tea.