Tetracycline adsorption on chitosan: A mechanistic description based on mass uptake and zeta potential measurements

Chitosan-Silica Composites for Adsorption Application in the Treatment of Water and Wastewater from Anionic Dyes

A series of new types of composites (biopolymer-silica materials) are proposed as selective and effective adsorbents. A new procedure for the synthesis of chitosan-nanosilica composites (ChNS) and chitosan-silica gel composites (ChSG) using geometrical modification of silica and mechanosorption of chitosan is applied. The highest adsorption efficiency was achieved at pH = 2, hence the desirability of modifications aimed at stabilizing chitosan in such conditions. The amount of chitosan in the synthesis grew to 1.8 times the adsorption capacity for the nanosilica-supported materials and 1.6 times for the silica gel-based composites. The adsorption kinetics of anionic dyes (acid red AR88) was faster for ChNS than for ChSG, which results from a silica-type effect. The various structural, textural, and physicochemical aspects of the chitosan-silica adsorbents were analyzed via small-angle X-ray scattering, scanning electron microscopy, low-temperature gas (nitrogen) adsorption, and potentiometric titration, as well as their adsorption effectiveness towards selected dyes. This indicates the synergistic effect of the presence of dye-binding groups of the chitosan component, and the developed interfacial surface of the silica component in composites.

Tailoring confined CdS quantum dots in polysulfone membrane for efficiently durable performance in solar-driven wastewater remediating systems

In this work, CdS quantum dots (QDs) were successfully confined in polysulfone membrane (PSM) to develop a photoactive membrane under solar illumination that was suited in wastewater remediating system. The CdS@PSM membranes were prepared using the nonsolvent induced phase separation (NIPS) approach. Optical measurements show the confinement of CdS quantum dots (QDs) in the PS matrix within the narrowest band gap (2.41 eV) at 5 wt% loading. PS has two strong emission peaks at 411 and 432 nm due to photoelectron-hole recombination on pure PSM's surface. Adding 1 wt% CdS QDs to PSM reduced the earlier peak and blue-shifted the latter, within the appearance of three emission peaks attributed to the near band-edge emission of confined CdS QDs. Overloading CdS reduced all emission peaks. Moreover, fluorimetric monitoring of ^•OH radicals indicates that PSM produces the least amount of photogenerated ^•OH radicals while CdS@PSM(5 wt%) achieved the highest productivity. Examining the developed membranes in detoxifying methylene blue (MB) from aqueous solution of natural pH 8.1 showed weak adsorption in dark over 90 min of contact while switching to solar illumination significantly photodegrade MB where the degradation efficiency starts from 49% for pure PSM to 79% for CdS@PSM(5 wt%). Influence of pH was found crucial on photodegradation efficacy. Acidic pH 3 showed the weakest photodegradation efficacy, while the alkaline pH 12 was 18.88 times more effective. The used CdS@PSM (5 wt%) was successfully photo-renovated by soaking in 10 mL of NaOH solution under Solar illumination for 15 min to be used in 4 consecutive photodegradation cycles with insignificant decrease in efficacy. These findings are promising and could lead to a high-efficiency, sustainable photocatalytic suite.

A Novel Adsorbent of Attapulgite & Carbon Composites Derived from Spent Bleaching Earth for Synergistic Removal of Copper and Tetracycline in Water

Simultaneously eliminating tetracycline (TC) and copper (Cu-II) from wastewater was investigated by applying a novel adsorbent fabricated by transforming spent bleaching earth (SBE) into attapulgite & carbon composites (A&Cs). Pyrolysis temperature for A&Cs preparation exhibited a positive effect on Cu(II) adsorption, while the AC500 possessed the greatest performance for TC remediation. Interestingly, a synergistic effect instead of competitive adsorption occurred between Cu(II) and TC under the combined binary system, as both TC and Cu(II) adsorption amount on A&C500 increased more than that in the single system, which could be mainly attributed to the bridge actions between the TC and Cu(II). In addition, hydrogen bonding, ᴨ-ᴨ EDA interaction, pore-filling and complexation exerted significant roles in the adsorption process of TC and Cu(II). In general, this study offered a new perspective on the regeneration of livestock and poultry industry wastewater polluted with antibiotics and heavy metals.

Preparation of P-doped CdS nanorods as an efficient photocatalyst for the degradation of the emerging pollutant tetracycline antibiotic under blue LED light irradiation

Excessive drug usage and sewage discharges containing antibiotics have caused water contamination due to the rapid growth of pharmaceutical industries. Tetracycline (TC) is one of the most frequently applied antibiotics having a significant impact on the aquatic environment, water quality and human health and thus effective approaches for TC removal from water are urgently needed. Here, we have fabricated P-doped CdS (CdS-P_0.8) nanorods (NRs) by one-step thermal phosphorization treatment for TC degradation through photocatalytic reaction in the presence of blue and white LED light irradiation. Synthesized photocatalysts were characterized to authenticate the incorporation of P atoms on the CdS NR surface using XPS, XRD, ICP-OES and EDX mapping analyses. CdS-P_0.8 NRs have greater photocatalytic activity for tetracycline degradation under blue LED light irradiation. TC degradation on CdS-P_0.8 NRs followed pseudo-first order kinetics for both LED light sources. In the presence of blue LED light at an intensity of 10 mW cm^-2, TC degradation efficiency and pseudo-first order rate constants of CdS-P_0.8 NRs for the photocatalytic degradation reaction reached 95.4% and 0.13396 min^-1 in 20 minutes without any supplemental oxygen sources. Scavenging experiments demonstrate that reactive oxygen species are produced during the photocatalytic degradation of tetracycline. As a result, due to the extensive utilization of photogenerated oxidative species such as h⁺, O₂˙^- and OH˙, CdS-P_0.8 NRs demonstrated high photocatalytic tetracycline degradation efficiency in 20 minutes. Our findings shed more light on nonmetal P doping on CdS materials and other semiconductors, exploring new possibilities for photocatalytic degradation to efficiently reduce the amount and toxicity of TC antibiotics in wastewater.

Synthesis and application of CdS nanorods for LED-based photocatalytic degradation of tetracycline antibiotic

With the rapid development of pharmaceutical industrialization, increased consumption of drugs and discharged sewage contains antibiotics that lead to water contamination. For this purpose, removal of antibiotics from aquatic environment is emphasizing the need to produce clean water using easy separable catalysts through photocatalytic water remediation and thus the semiconductor photocatalysts have presently gained fascinating unprecedented research attention. Herein, we present the synthesis of semiconductor CdS nanorods by a facile hydrothermal procedure using ethylene diamine as a coordinating agent. Then, we subsequently studied the photocatalytic activity of CdS nanorods under blue and white LED light irradiation for the degradation of tetracycline antibiotic as a model compound. The light dependent photocatalytic activity of CdS nanorods demonstrated that CdS nanorods possess higher catalytic efficiency in presence of blue light compared to white light toward the photocatalytic degradation of tetracycline antibiotic. We have also studied the photocatalytic activity in presence of various light intensity. These CdS nanorods exhibited the highest tetracycline degradation efficacy of 95.6% within 60 min in presence of blue light (intensity: 200W/m²) without any supplementary oxygen sources during the degradation reaction. The photocatalytic mechanism of the tetracycline degradation has been elucidated by scavenging experiment. The experimental results indicate the formation of reactive oxygen species during photocatalytic degradation of tetracycline antibiotic. This work represents an alternative route to develop heterogeneous photocatalyst for antibiotics degradation due to the outstanding efficiency and stability of the CdS nanorods as well as easy separation through simple filtration method. It is anticipated that this work will shed light in the practical applications of CdS nanorods for environmental remediation through wastewater treatment.

Carbon source type can affect tetracycline removal by Pseudomonas sp. TC952 through regulation of extracellular polymeric substances composition and production

The objective of this work is to elucidate the mechanism of tetracycline (TC) removal by Pseudomonas sp. TC952. The TC removal characteristics of strain TC952 under various environmental conditions were studied. Results showed that the bio-removal efficiency was significantly affected by initial TC and peptone concentration, pH values, divalent metal ion (Zn²⁺) and carbon source, and the strain TC952 efficiently removed approximately 72.8% of TC within 6 days with 10 g/L peptone. The best conditions for strain TC952 to remove TC are as follows: initial TC concentration is 50 mg/L, solution initial pH is 7, Zn²⁺ concentration is 0.1 μg/L, carbon source is peptone. And through intra- and extracellular fractions assay and extracellular polymeric substances (EPS) component analysis, TC removal by strain TC952 was mainly attributed to the adsorption by bacterial EPS and bacterial cell. Furthermore, different carbon source affected the EPS production content and component of strain TC952, so EPS produced under peptone and serine conditions could bio-adsorb TC and formed a buffer area outside the cells, thus reducing or preventing TC from entering the bacteria cells. All the results obtained showed that secretion of EPS and adsorption of TC by EPS and bacterial cell wall may be a common way for bacteria to reduce TC in the environment, which brought novel insights for better management of TC contamination by functional bacteria and for understanding the natural removal process of antibiotics by microorganisms in the environment.

Magnetic spent bleaching earth carbon (Mag-SBE@C) for efficient adsorption of tetracycline hydrochloride: Response surface methodology for optimization and mechanism of action

The utilization of spent bleaching earth (SBE)-based materials for adsorption of pollutants from water and wastewater has received growing attention. In this work, a comparative study of magnetic spent bleaching earth carbon (Mag-SBE@C) and spent bleaching earth carbon (SBE@C) was performed to remove tetracycline hydrochloride (TCH) from aqueous solutions. Mag-SBE@C exhibits the larger adsorption capacity (0.238 mmol/g) obtained by the Langmuir model than the original SBE@C (0.150 mmol/g). The adsorption process fits well with the pseudo second-order model and is found to be exothermic (ΔH₀ < 0) and spontaneous (ΔG₀ < 0). The optimal adsorption conditions (Mag-SBE@C dose 2.217 g/L, initial TCH concentration 0.113 mmol/L, initial solution pH 6.533) predicted by the response surface methodology (RSM) are consistent with the actual verification results. The inhibition extents of coexisting cations are ranked in a decline: Al³⁺ > Cu²⁺ > Fe³⁺ > Mg²⁺ > K⁺ > Na⁺. Various characterization results indicate that the adsorption mechanism of TCH by Mag-SBE@C likely includes the π-π interactions, hydrogen bonding, electrostatic interactions, π-cations interactions, FeN covalent bonding, and changes in physical and chemical properties. Mag-SBE@C is easily solid-liquid separated using magnetic field, and can be potentially reused for 13 times before completely losing its activity, exhibiting great potential to antibiotics elimination.

Effect of dissolved organic matter on adsorption of sediments to Oxytetracycline: An insight from zeta potential and DLVO theory

To reveal the adsorption mechanism of sediment to antibiotics with the presence of dissolved organic matter (DOM), batch experiments were carried out by oxytetracycline (OTC) on sediments with decayed plants (PDOM) and composted chicken manure (MDOM), and the zeta potential in the system before and after adsorption was measured. Results showed that the PDOM promoted the adsorption process, while the MDOM inhibited the adsorption. Adding PDOM, the change of zeta potential (Δζ) increased by 40.08% for first terrace sediments (FT) and 63.98% for riverbed sediments (RB), respectively; meanwhile, MDOM decreased by 20.04% for FT and 28.39% for RB, respectively. The results of kinetic fitting models of replacing the adsorption amount with Δζ were consistent with the initial. It indicated that there was a positive correlation between the adsorption amount and Δζ, and the zeta potential can be used to quickly judge the degree of adsorption process. The Derjaguin-Landau-Verwey-Overbeek (DLVO) theory describes the interactions of sediment particles. In terms of adsorption amount, zeta potential (absolute value) and total interaction energy all followed the order: RB > FT, RB-PDOM > FT-PDOM, and RB-MDOM > FT-MDOM. The more negative the zeta potential is, the better the dispersion of the particles is. Stronger repulsion is more conducive to adsorbing positively charged OTC. The site energy distribution theory further explained that the distribution of adsorption site in the various states of sediments increased while adding the PDOM and decreased while adding the MDOM.

Mechanism of enhancing pyrene-degradation ability of bacteria by layer-by-layer assembly bio-microcapsules materials

The mechanism of improving pyrene (PYR)-degrading ability of bacteria CP13 in Layer-by-layer (LBL) assembly chitosan/alginate (CHI/ALG) bio-microcapsules was investigated. Flow cytometry analysis showed that LBL microcapsules could effectively slow down the increasing rate of bacterial cell membrane permeability and the decreasing rate of the membrane potential, so as to reduce the death rate and number of the cells, which could protect the degrading bacteria. The results of Fluorescence spectrum, circular dichroism (CD) spectrum and laser light scattering (LLS) analysis revealed that the other possible mechanism for LBL microcapsules to promote bacterial degradation were following: CHI could enter the secondary structure of the protein of the extracellular polymeric substances (EPS) from CP13 and combined with EPS to generate a stable ground material, which had larger molecular weight (3.76×10⁶ g mol^-1) than the original EPS (2.52×10⁶ g mol^-1). The combination of CHI and EPS resulted in the decrease of the density of EPS from 1.18 to 0.72 g L^-1, suggesting that CHI can loosen the EPS configurations, improving the capture ability of bacteria for PYR as well as the mass transfer of PYR from the extracellular to intracellular, thus eventually promoting the bacteria degrade performance.

Blend-electrospun graphene oxide/Poly(vinylidene fluoride) nanofibrous membranes with high flux, tetracycline removal and anti-fouling properties

Graphene oxide (GO)/poly(vinylidene fluoride) (PVDF) electrospun nanofibrous membranes (ENMs) have been fabricated to remove tetracycline (TC) from water via adsorptive-filtration. The pure water permeation flux of GO/PVDF ENMs (27,407-29,337 LMH/bar) was increased compared with that of PVDF ENMs. The flow pore diameter was steadily reduced by increasing the GO content from 0 to 1.5 wt% in the GO/PVDF ENMs. The maximum TC adsorption capacity of GO is 720.26 mg/g (Langmuir model) and GO retained its TC adsorption property after incorporation into GO/PVDF ENMs during water filtration (transmembrane pressure = 0.91 bar). The maximum experimental TC removal capacity (q_a,_exp) was 17.92 mg/g with 1.5 wt% of GO (GO_1.5/PVDF) ENMs, which was similar to the modified dose-response model value of 18.03 mg/g. In the presence of natural organic matter, TC adsorption was enhanced, because hydrophobic organic carbon improved hydrophobic and π-π interactions. The presence of Cu(II) further improved the TC adsorption capacity of GO_1.5/PVDF ENMs through cation bridging. However, the presence of Ca(II) hindered TC adsorption by an electron shielding effect. For examining anti-fouling activity of GO_1.5/PVDF ENMs, the log removal values of both bacteria, Escherichia coli and Staphylococcus aureus, were maintained at over 5 during water filtration. In addition, incorporation of GO in PVDF ENMs prevents bovine serum albumin (BSA) adsorption by both increasing the hydrophilicity of the ENMs forming hydration layer on the surface and electrostatic repulsion between both negatively charged BSA and GO in GO_1.5/PVDF ENMs (zeta potential = - 14.14 mV, deionized water at pH 6).

Immobilization of an antimicrobial peptide on silicon surface with stable activity by click chemistry

We click an antimicrobial peptide onto a silicon substrate to protect it from enzymolysis using a polySBMA spacer.

Efficient Removal of Tetracycline from Aqueous Media with a Fe₃O₄ Nanoparticles@graphene Oxide Nanosheets Assembly

A readily separated composite was prepared via direct assembly of Fe₃O4 magnetic nanoparticles onto the surface of graphene oxide (GO) (labeled as Fe₃O₄@GO) and used as an adsorbent for the removal of tetracycline (TC) from wastewater. The effects of external environmental conditions, such as pH, ionic strength, humic acid (HA), TC concentration, and temperature, on the adsorption process were studied. The adsorption data were analyzed by kinetics and isothermal models. The results show that the Fe₃O₄@GO composite has excellent sorptive properties and can efficiently remove TC. At low pH, the adsorption capacity of Fe₃O₄@GO toward TC decreases slowly with increasing pH value, while the adsorption capacity decreases rapidly at higher pH values. The ionic strength has insignificant effect on TC adsorption. The presence of HA affects the affinity of Fe₃O₄@GO to TC. The pseudo-second-order kinetics model and Langmuir model fit the adsorption data well. When the initial concentration of TC is 100 mg/L, a slow adsorption process dominates. Film diffusion is the rate limiting step of the adsorption. Importantly, Fe₃O₄@GO has good regeneration performance. The above results are of great significance to promote the application of Fe₃O₄@GO in the treatment of antibiotic wastewater.

Preparation of active 3D film patches via aligned fiber electrohydrodynamic (EHD) printing

The design, preparation and application of three-dimensional (3D) printed structures have gained appreciable interest in recent times, particularly for drug dosage development. In this study, the electrohydrodynamic (EHD) printing technique was developed to fabricate aligned-fiber antibiotic (tetracycline hydrochloride, TE-HCL) patches using polycaprolactone (PCL), polyvinyl pyrrolidone (PVP) and their composite system (PVP-PCL). Drug loaded 3D patches possessed perfectly aligned fibers giving rise to fibrous strut orientation, variable inter-strut pore size and controlled film width (via layering). The effect of operating parameters on fiber deposition and alignment were explored, and the impact of the film structure, composition and drug loading was evaluated. FTIR demonstrated successful TE-HCL encapsulation in aligned fibers. Patches prepared using PVP and TE-HCL displayed enhanced hydrophobicity. Tensile tests exhibited changes to mechanical properties arising from additive effects. Release of antibiotic from PCL-PVP dosage forms was shown over 5 days and was slower compared to pure PCL or PVP. The printed patch void size also influenced antibiotic release behavior. The EHDA printing technique provides an exciting opportunity to tailor dosage forms in a single-step with minimal excipients and operations. These developments are crucial to meet demands where dosage forms cannot be manufactured rapidly or when a personalized approach is required.

Hydrophilic, hollow Fe3O4@PDA spheres with a storage cavity for efficient removal of polycyclic structured tetracycline

Biomimetic hydrophilic hollow polydopamine (PDA)-based composites of Fe₃O₄@PDA for the efficient removal of polycyclic structured tetracycline were facilely synthesized.

Visible light activated photocatalytic degradation of tetracycline by a magnetically separable composite photocatalyst: Graphene oxide/magnetite/cerium-doped titania

In this study, magnetic graphene oxide-loaded Ce-doped titania (MGO-Ce-TiO2) hybridized composite was prepared by a facile method. The as-prepared samples exhibited good adsorption capacity, high visible-light photoactive and magnetic separability as a novel photocatalyst in the degradation of tetracyclines (TC). The intermediate products and photocatalytic route of TC were proposed based on the analysis results of LC-MS. Moreover, the repeatability of the photoactivity with the use of MGO-Ce-TiO2 was investigated in the multi-round experiments with the assistance of an applied magnetic field. Therefore, the prepared composite photocatalysts were considered as a kind of promising photocatalyst in a suspension reaction system, in which they can offer effectively recovery ability. The effect of MGO content on the photocatalytic performance was also studied, and an optimum content was obtained.

Preparation of magnetic activated carbon from waste rice husk for the determination of tetracycline antibiotics in water samples

Preparation of magnetic activated carbon by a natural template strategy and determination of the pre-concentrations of tetracycline antibiotics in water samples.

Facile method for the synthesis of a magnetic CNTs–C@Fe–chitosan composite and its application in tetracycline removal from aqueous solutions

A new type of biocomposite, as-prepared carbon nanotubes–chitosan (APCNTs–CS), was prepared and characterized.

Characterization of the interactions between tetracycline antibiotics and microbial extracellular polymeric substances with spectroscopic approaches

The antibiotics have attracted global attentions for their impact on aquatic ecosystem. The knowledge about the fate of antibiotics encountering extracellular polymeric substances (EPS) is, however, limited. In this study, we investigated the interacting mechanisms of tetracycline (TC) to EPS extracted from aerobic activated sludge. The contributions of the main components of EPS, extracellular proteins, and polysaccharides were evaluated using bovine serum albumin and alginate sodium, respectively. Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and nuclear magnetic resonance indicated that hydroxyl, carboxyl, and amino groups were the domain chemical groups involved in the interaction between TC and EPS, and the binding of TC onto EPS changed the structure of these chemical groups, thus causing shifts in their UV-visible absorption spectra. In addition, we found that extracellular proteins, rather than polysaccharides, were the major active contents involved in the interaction. Three-dimensional excitation-emission matrix fluorescence spectroscopy showed that the fluorophores in EPS were clearly quenched by TC and the static quenching process was observed, implying the complex formation of TC and EPS. Furthermore, thermodynamic analysis indicated that the binding of TC with EPS is spontaneous and dominated by electrostatic forces.

In vitro analysis of nanoparticulate hydroxyapatite/chitosan composites as potential drug delivery platforms for the sustained release of antibiotics in the treatment of osteomyelitis

Nanoparticulate composites of hydroxyapatite (HAp) and chitosan were synthesized by ultrasound-assisted sequential precipitation and characterized for their microstructure at the atomic scale, surface charge, drug release properties, and combined antibacterial and osteogenic response. Crystallinity of HAp nanoparticles was reduced because of the interference of the surface layers of chitosan with the dissolution/reprecipitation-mediated recrystallization mechanism that conditions the transition from the as-precipitated amorphous calcium phosphate phase to the most thermodynamically stable one--HAp. Embedment of 5-10 nm sized, narrowly dispersed HAp nanoparticles within the polymeric matrix mitigated the burst release of the small molecule model drug, fluorescein, bound to HAp by physisorption, and promoted sustained-release kinetics throughout the 3 weeks of release time. The addition of chitosan to the particulate drug carrier formulation, however, reduced the antibacterial efficacy against S aureus. Excellent cell spreading and proliferation of osteoblastic MC3T3-E1 cells evidenced on microscopic conglomerates of HAp nanoparticles in vitro also markedly diminished on HAp/chitosan composites. Mitochondrial dehydrogenase activity exhibited normal values only for HAp/chitosan particle concentrations of up to 2 mg/cm(2) and significantly dropped, by about 50%, at higher particle concentrations (4 and 8 mg/cm(2)). The gene expression of osteocalcin, a mineralization inductor, and the transcription factor Runx2 was downregulated in cells incubated in the presence of 3 mg/cm(2) HAp/chitosan composite particles, whereas the expression of osteopontin, a potent mineralization inhibitor, was upregulated, further demonstrating the partially unfavorable osteoblastic cell response to the given particles. The peak in the expression of osteogenic markers paralleling the osteoblastic differentiation was also delayed most for the cell population incubated with HAp/chitosan particles. Overall, the positive effect of chitosan coating on the drug elution profile of HAp nanoparticles as carriers for the controlled delivery of antibiotics in the treatment of osteomyelitis was compensated for by the lower bacteriostatic efficiency and the comparatively unviable cell response to the composite material, especially at higher dosages.

Adsorption properties of tetracycline onto graphene oxide: equilibrium, kinetic and thermodynamic studies

Graphene oxide (GO) nanoparticle is a high potential effective absorbent. Tetracycline (TC) is a broad-spectrum antibiotic produced, indicated for use against many bacterial infections. In the present research, a systematic study of the adsorption and release process of tetracycline on GO was performed by varying pH, sorption time and temperature. The results of our studies showed that tetracycline strongly loads on the GO surface via π-π interaction and cation-π bonding. Investigation of TC adsorption kinetics showed that the equilibrium was reached within 15 min following the pseudo-second-order model with observed rate constants of k2 = 0.2742-0.5362 g/mg min (at different temperatures). The sorption data has interpreted by the Langmuir model with the maximum adsorption of 323 mg/g (298 K). The mean energy of adsorption was determined 1.83 kJ/mol (298 K) based on the Dubinin-Radushkevich (D-R) adsorption isotherm. Moreover, the thermodynamic parameters such as ΔH°, ΔS° and ΔG° values for the adsorption were estimated which indicated the endothermic and spontaneous nature of the sorption process. The electrochemistry approved an ideal reaction for the adsorption under electrodic process. Simulation of GO and TC was done by LAMMPS. Force studies in z direction showed that tetracycline comes close to GO sheet by C8 direction. Then it goes far and turns and again comes close from amine group to the GO sheet.

Equilibrium and kinetic aspects of sodium cromoglycate adsorption on chitosan: mass uptake and surface charging considerations

Chitosan has more and more been suggested as a material for use as adsorbent in the treatment of effluents as well as in the synthesis of drug-loaded nanoparticles for controlled release. In both cases, a good understanding of the process of adsorption, both kinetically and in terms of equilibrium, has an importance of its own. In this manuscript we study the interaction between sodium cromoglycate, a drug used in asthma treatment, and chitosan. Equilibrium experiments showed that Sips (or Freundlich-Langmuir) isotherm described well the resultant data and adsorption possibly occurred as in multilayers. A model based on ordinary reaction-rate theory, compounded of two processes, each one with a correlated velocity constant, described the kinetics of sorption. Kinetic and equilibrium data suggested the possibility of surface rearrangement, favored by the increase of temperature.