Ion release from, and fluoride recharge of a composite with a fluoride-containing bioactive glass

Marginal integrity of prototype bioactive glass-doped resin composites in class II cavities

OBJECTIVES

This in vitro study examined the marginal integrity of experimental composite materials doped with bioactive glass (BG).

MATERIALS AND METHODS

Class-II MOD cavities were prepared and restored with one of the following composite materials: a commercial composite material as a reference (Filtek Supreme XTE), an experimental composite doped with BG 45S5 (C-20), and an experimental composite doped with a fluoride-containing BG (F-20). Six experimental groups (n = 8) were used, as each of the three composites was applied with (+) or without (-) a universal adhesive (Adper Scotchbond Multipurpose). All specimens were subjected to thermocycling (10,000 x, 5-55 °C) and then additionally stored in artificial saliva for eight weeks. Scanning electron micrographs of the mesial and the distal box were taken at three time points (initial, after thermocycling, and after eight weeks of storage in artificial saliva). The margins were classified as "continuous" and "non-continuous" and the percentage of continuous margins (PCM) was statistically analyzed (α = 0.05).

RESULTS

In most experimental groups, thermocycling led to a significant decrease in PCM, while the additional 8-week aging had no significant effect. F-20 + performed significantly better (p = 0.005) after 8 weeks storage in artificial saliva than the reference material with adhesive, while no statistically significant differences were observed at the other two time points. C-20 + exhibited significantly better PCM than the reference material with adhesive after thermocycling (p = 0.026) and after 8 weeks (p = 0.003).

CONCLUSIONS

Overall, the experimental composites with BG showed at least as good marginal adaptation as the commercial reference, with an indication of possible re-sealing of marginal gaps.

CLINICAL RELEVANCE

Maintaining or improving the marginal integrity of composite restorations is important to prevent microleakage and its likely consequences such as pulp irritation and secondary caries.

Novel pit and fissure sealant with nano-CaF2 and antibacterial monomer: Fluoride recharge, microleakage, sealing ability and cytotoxicity

Conventional resin-based sealants release minimal fluoride ions (F) and lack antibacterial activity. The objectives of this study were to: (1) develop a novel bioactive sealant containing calcium fluoride nanoparticles (nCaF2) and antibacterial dimethylaminohexadecyl methacrylate (DMAHDM), and (2) investigate mechanical performance, F recharge and re-release, microleakage, sealing ability and cytotoxicity. Helioseal F served as commercial control. The initial F release from sealant containing 20% nCaF2 was 25-fold that of Helioseal F. After ion exhaustion and recharge, the F re-release from bioactive sealant did not decrease with increasing number of recharge and re-release cycles. Elastic modulus of new bioactive sealant was 44% higher than Helioseal F. The new sealant had excellent sealing, minimal microleakage, and good cytocompatibility. Hence, the nanostructured sealant had substantial and sustained F release and antibacterial activity, good sealing ability and biocompatibility. The novel bioactive nCaF2 sealant is promising to provide long-term F ions for caries prevention.

New generation of orthodontic devices and materials with bioactive capacities to improve enamel demineralization

OBJECTIVE

The article reviewed novel orthodontic devices and materials with bioactive capacities in recent years and elaborated on their properties, aiming to provide guidance and reference for future scientific research and clinical applications.

DATA, SOURCES AND STUDY SELECTION

Researches on remineralization, protein repellent, antimicrobial activity and multifunctional novel bioactive orthodontic devices and materials were included. The search of articles was carried out in Web of Science, PubMed, Medline and Scopus.

CONCLUSIONS

The new generation of orthodontic devices and materials with bioactive capacities has broad application prospects. However, most of the current studies are limited to in vitro studies and cannot explore the true effects of various bioactive devices and materials applied in oral environments. More research, especially in vivo researches, is needed to assist in clinical application.

CLINICAL SIGNIFICANCE

Enamel demineralization (ED) is a common complication in orthodontic treatments. Prolonged ED can lead to dental caries, impacting both the aesthetics and health of teeth. It is of great significance to develop antibacterial orthodontic devices and materials that can inhibit bacterial accumulation and prevent ED. However, materials with only preventive effect may fall short of addressing actual needs. Hence, the development of novel bioactive orthodontic materials with remineralizing abilities is imperative. The article reviewed the recent advancements in bioactive orthodontic devices and materials, offering guidance and serving as a reference for future scientific research and clinical applications.

Effect of bioactive glass-containing dentin adhesives on microshear bond strength of composite restorations

Background

In general, bioactive glasses (BAGs) can react with tissue minerals and promote remineralization. However, the application of BAG in bonding agents and its impact on bond strength remain uncertain due to insufficient information and limited research in this area.

Materials and Methods

This study employed a randomized controlled design to assess the effects of composite-bonding agents with varying BAG contents on shear bond strength and fracture pattern in sound and demineralized teeth, with and without thermocycling. Thus, 80 healthy third molars were randomly divided into two groups: sound teeth and demineralized teeth. Five bonding agents were applied to the prepared dentin surfaces, including four experimental composite-bonding agents with varying BAG content (0, 0.2, 0.5, and 2 wt%) and the Adper Single Bond commercial bonding as control. The shear bond strength of all samples was measured using a universal tester. The type of failure of each specimen was determined using a stereomicroscope. Kruskal-Wallis nonparametric test was performed on the obtained shear bond strength data followed by Mann-Whitney post hoc test with Bonferroni correction to determine statistical significance. The level of significance was considered P ≤ 0.05 for all tests and was adjusted by Bonferroni correction.

Results

Demineralization significantly decreased shear bond strength in the teeth samples. Adper Single Bond exhibited the highest shear bond strength values. The addition of BAG did not have a significant influence on shear bond strength, regardless of demineralization or thermocycling condition. Adhesive failure was the predominant type of failure in all groups.

Conclusion

The incorporation of BAG filler up to 2 wt% did not result in significant changes in shear bond strength. Experimental adhesive bonding agents with 2 wt% BAG content demonstrated shear bond strengths comparable to the commercial bonding agent in sound nontreated, sound thermocycled, demineralized nontreated, and demineralized thermocycled groups.

Real-Time Monitoring of Biofilm Formation Using a Noninvasive Impedance-Based Method

Biofilms are complex three-dimensional microbial communities that adhere to a variety of surfaces and interact with their surroundings. Because of the dynamic nature of biofilm formation, establishing a uniform technique for quantifying and monitoring biofilm volume, shape, and features in real-time is challenging. Herein, we describe a noninvasive electrochemical impedance approach for real-time monitoring of dental plaque-derived multispecies biofilm growth on a range of substrates. A working equation relating electrochemical impedance to live biofilm volume has been developed that is applicable to all three surfaces examined, including glass, dental filling resin, and Ca2+-releasing resin composites. Impedance changes of 2.5, 35, 50, and 65% correlated to biofilm volumes of 0.10 ± 0.01, 16.9 ± 2.2, 29.7 ± 2.3, and 38.6 ± 2.8 μm3/μm2, respectively. We discovered that glass, dental filling resin, and Ca2+-releasing dental composites required approximately 3.5, 4.5, and 6 days, respectively, to achieve a 50% change in impedance. The local pH change at the biofilm-substrate interfaces also monitored with potentiometry pH microsensor, and pH change varied according to biofilm volume. This impedance-based technique can be a useful analytical method for monitoring the growth of biofilms on a variety of substrates in real-time. Therefore, this technique may be beneficial for examining antibacterial properties of novel biomaterials.

Effects of an orthodontic primer containing amorphous fluorinated calcium phosphate nanoparticles on enamel white spot lesions

OBJECTIVES

The study investigated the effects of an orthodontic primer containing amorphous fluorinated calcium phosphate (AFCP) nanoparticles on enamel white spot lesions (WSLs).

MATERIALS AND METHODS

The AFCP nanoparticles were prepared and incorporated into Transbond XT Primer. Thirty-two human enamel slices were highly polished and randomly divided into four groups: no part covered (control), half covered with a primer containing 0 wt%, 25 wt%, and 35 wt% AFCP. Subsequently, samples were challenged by a modified pH-cycling and characterized by color measurement, micro-computed tomography, and scanning electron microscope (SEM). The bonding properties of the primers containing AFCP were assessed using shear bond strength test, and the mouse fibroblasts (L929) were employed to evaluate the cytotoxicity.

RESULTS

When the enamel was challenged by pH cycling, 25 wt% and 35 wt% AFCP groups exhibited less color change (ΔE) and less mineral loss than the control and 0 wt% AFCP groups. The SEM images showed that the original microstructural integrity and mineral deposition rate of the enamel surface were better in the 25 wt% and 35 wt% AFCP groups. In particular, the 35 wt% AFCP group exhibited the best performance after 3 weeks of pH cycling. The shear bond strength and cell viability revealed no significant difference among the tested groups (P > 0.05).

CONCLUSION

Using the primer containing 35 wt% AFCP might be a promising strategy for preventing the occurrence and development of WSLs during orthodontic treatment.

A Narrative Review of Bioactive Glass-Loaded Dental Resin Composites

This review aims to provide a comprehensive analysis of the characterizations of bioactive glass (BAG)-loaded dental resin-based composite materials. Online databases (Web of Science, PubMed, and Science Direct) were used to collect data published from January 2011 to January 2022. Only BAG-containing resin adhesive and resin restorative composites are discussed in this narrative review. BAG-loaded resin composites exhibit excellent mineralization ability reflecting enhanced ion release, pH elevation, and apatite formation, especially regarding high BAG loading. This aids the anti-demineralization and remineralization of teeth. Furthermore, BAG-loaded resin composites demonstrated in vitro biocompatibility and antibacterial performance. It has been suggested that BAG fillers with small particle sizes and no more than 20 wt% in terms of loading amount should be used to guarantee the appropriate mechanical properties of resin composites. However, most of these studies focused on one or some aspects using different resin systems, BAG types, and BAG amounts. As such, this makes the comparison difficult, and it is essential to find an optimal balance between different properties. BAG-loaded resin composites can be regarded as bioactive materials, which present major benefits in dentistry, especially their capability in the bacterial inhibition, cell biocompatibility, anti-demineralization, and remineralization of teeth.

Novel Fluoride- and Chloride-containing Bioactive Glasses for Use in Air Abrasion

OBJECTIVES

To investigate the degradation, fluorapatite formation, biological safety and cutting efficiency on dentine of the mixed fluoride- and chloride-containing bioactive glasses (BGs).

METHODS

Two series of mixed fluoride- and chloride-containing glasses (GPFCl and GPF2.3Cl series) were synthesized using a melt-quench method. Glass transition temperature (T_g) and the bioactivity in term of glass degradation and fluorapatite formation were evaluated in Tris buffer solution. The cutting efficiency of the powdered BGs (GPF2.3Cl series) on dentine via air abrasion was investigated using white light profilometry and scanning electron microscope. The cytotoxicity of GPF2.3Cl series on human periodontal ligament stem cells (hPLSCs) and oral fibroblasts (OFB) were examined by MTT.

RESULTS

These BGs are highly degradable and able to form fluorapatite within 3h of immersion. The formation of CaF₂ was also found in the high fluoride-containing BGs. The faster glass degradation was evidenced in the BGs with higher chloride. A significant reduction of T_g from 790°C to 463°C was seen with increasing in calcium halide content. Air abrasion on dentine using the low and intermediate chloride-containing glasses demonstrates clear depressions, while no depression was found using the high chloride-containing glass. Moreover, the studied BGs showed no cytotoxicity to hPLSCs and OFB.

CONCLUSIONS

The glasses with mixed fluoride and chloride integrate the benefits from the presence of both, showing rapid glass degradation, fast fluorapatite formation, excellent biocompatibility and controllable hardness to provide a selective cutting efficiency on dentine.

CLINICAL SIGNIFICANCE

The developed BGs air abrasive with tunable hardness by varying chloride content can selectively cut different dental tissues. In clinic, a relatively hard BG is of great interest for caries preparation, while a soft glass is attractive for tooth cleaning.

The Effect of Flowable Composite Resins on Periodontal Health, Cytokine Levels, and Immunoglobulins

Objective

This study investigated the effects of flowable resin composites (FCR) on the restoration of noncarious cervical lesions (NCCL) and their impact on periodontal tissues.

Materials and Methods

30 periodontally healthy patients were assigned into three groups randomly; group VF: self-adhering FCR, group NF: fluoride-releasing FCR, and group SF: microhybrid FCR. Gingival crevicular fluid (GCF) volume levels of osteoprotegerin (OPG), immunoglobulins (IgA, IgM), and interleukins (IL-1, IL-1β, and IL-10) in GCF were analyzed with ELISA tests. Clinical success rates were evaluated using USPHS criteria during the 12-month follow-up.

Results

The GCF volume was increased mostly in group SF (1.34 ± 0.09 μl). While the titer of interleukin was increased in all groups, higher increases were observed in IL-1 and IL-1β in group NF (170.78 pg/ml and 39.35 pg/ml). Increased IL-10 was observed in group VF (14.33 ± 0.85 pg/ml). IgA levels varied partially among all groups (p > 0.05), and even IgM levels were elevated immediately after the restoration process but returned to normal on the 28th day (p < 0.05). Group NF failed in most of the USPHS criteria, while the material group VF and group SF presented acceptable results except in the marginal adaptation criterion (p < 0.05).

Conclusions

Clinical efficacy of self-adhering FCR was found the best for restoration of NCCL while fluoride-releasing FCR stimulated the periodontal response and had negative effects on GCF volume, cytokine, and immunoglobulin levels.

Sol-gel bioactive glass containing biomaterials for restorative dentistry: A review

OBJECTIVE

Bioactive glasses (BAGs) have been researched extensively for dentistry due to their favourable biocompatibility and hard tissue bonding ability. However, the specific application of BAGs produced through sol-gel synthesis in restorative dentistry has not been reviewed previously. This review provides a comprehensive account of the principles behind sol-gel derived BAGs and their investigation for dental tissue restoration materials.

METHODS

A search for in vitro and in vivo studies was performed using the databases Web of Science®, Medline®, Scopus® and Google Scholar®. Articles published over the past 20 years were selected and data on the BAG composition and morphology was extracted. Analysis of the effect of specific BAG additives on the properties of experimental dental materials was also performed.

RESULTS

A majority of BAG particles investigated were spheres ranging in size from 5 nm to ~650 µm. Sol-gel BAGs are mainly applied in the treatment of hypersensitive dentine and for pulp-dentine tissue engineering, while a handful have been used in target drug delivery. BAG fillers are promising additives that result in improved biological properties, antibacterial effects, hardness, acid buffering and remineralization. Unfortunately, some detrimental effects on optical properties have been observed with BAG addition. Additionally, in vivo data, investigations into radiopacity and standardization of test protocols are identified as areas for improvement and further studies.

SIGNIFICANCE

Future work should consider the pertinent issues raised in order to improve the quality of available data and expand knowledge in this area of dental biomaterials research and development.

A biomimetic approach to evaluate mineralization of bioactive glass-loaded resin composites

PURPOSE

This study explores novel solutions other than standard SBF for biomimetic evaluations of mineralization particularly for resin composites containing bioactive glass (BAG).

METHODS

Experimental UDMA/TEGDMA resin composites with 0.0, 1.9, 3.8 or 7.7 vol% of 45S5 BAG fillers were prepared. Besides simulated body fluid (SBF) as control, the specimens were immersed in three other solutions either with bicarbonate which are Hank's balanced salt solution (HBSS) and cell culture medium (MEM), or without bicarbonate which is a novel Simple HEPES-containing Artificial Remineralization Promotion (SHARP) solution, for 3, 7 and 14 days. These solutions were then analyzed by ICP-OES and pH, and the surfaces of the BAG composites were analyzed by SEM, XRD and FTIR.

RESULTS

ICP-OES revealed Ca and P concentration continuously decrease, while Si concentration increases with time in the solutions other than SBF, which showed almost unchanged elemental concentration. Only SHARP solution is able to maintain a constant pH over the immersion time. SEM, together with XRD and FTIR, showed nano-sized octacalcium phosphate (OCP) nanospheres formation on 3.8 and 7.7 vol% BAG composites after 14 days immersion in HBSS (500-600 nm) and MEM (300-400 nm). SHARP solution enabled OCP formation after 3 days and then self-assembled into urchin-like carbonated hydroxyapatite (CHA) microspheres encompassed with nanorods of 100 nm width and 8 µm length after 14 days of immersion for 7.7 vol% BAG composites.

CONCLUSION

This study suggests SHARP solution can evaluate mineralization biomimetically whereas CHA microspheres can be formed on BAG-containing resin composites.

Ion release and hydroxyapatite precipitation of resin composites functionalized with two types of bioactive glass

OBJECTIVES

To prepare experimental composites with bioactive glass (BG) and investigate their release of calcium (Ca), phosphate (PO₄), and fluoride (F), as well as pH changes and apatite precipitation after immersion.

METHODS

Experimental composites were prepared with 0, 10, or 20 wt% of either BG 45S5 or a customized low-Na F-containing BG. Three commercial ion-releasing materials were used for reference. Material specimens were immersed in lactic acid (pH = 4.0) and artificial saliva (pH = 6.4). Ion concentrations (atomic absorption spectrometry for Ca, UV-vis spectrometry for PO₄, and ion-selective electrode for F) and pH were measured after 4, 8, 12, 16, 20, 24, 28, and 32 days. After immersion, composite specimens were analyzed using scanning electron microscopy (SEM) and Fourier-transform infrared (FTIR) spectroscopy.

RESULTS

Material-dependent concentrations of Ca, PO₄, and F were measured in the lactic acid solution, while a decrease of Ca and PO₄ concentrations was observed in artificial saliva. The uptake of ions from artificial saliva indicates their precipitation on specimen surfaces, which was supported by the results of SEM and FTIR investigations. In experimental composites functionalized with both bioactive glass types and a commercial "alkasite" material, apatite was precipitated not only in artificial saliva but also in the lactic acid solution.

CONCLUSIONS

Experimental BG-containing composites and selected commercial restorative materials demonstrated the potential for releasing multiple ion types and increasing pH.

CLINICAL SIGNIFICANCE

The observed effects can be beneficial for preventing demineralization and promoting remineralization of dental hard tissues, while apatite precipitation can additionally help in sealing marginal discontinuities.

Novel rechargeable calcium fluoride dental nanocomposites

OBJECTIVES

Composite restorations with calcium fluoride nanoparticles (nCaF₂) can remineralize tooth structure through F and Ca ion release. However, the persistence of ion release is limited. The objectives for this study were to achieve long-term remineralization by developing a rechargeable nCaF₂ nanocomposite and investigating the F and Ca recharge and re-release capabilities.

METHODS

Three nCaF₂ nanocomposites were formulated: (1) BT-nCaF₂:Bisphenol A glycidyl dimethacrylate (BisGMA) and triethylene glycol dimethacrylate (TEGDMA); (2) PE-nCaF₂:Pyromellitic glycerol dimethacrylate (PMGDM) and ethoxylated bisphenol A dimethacrylate (EBPADMA); (3) BTM-nCaF₂:BisGMA, TEGDMA, and Bis[2-(methacryloyloxy)ethyl] phosphate (Bis-MEP). All formulations contained 15% nCaF₂ and 55% glass particles. Initial flexural strength and elastic modulus, F and Ca ion release, recharge and re-release were tested and compared to three commercial fluoride-containing materials.

RESULTS

BT and BTM nCaF₂ composites were 3-4 times stronger and had elastic modulus 2 times that of resin-modified glass ionomer controls. PE-nCaF₂ had comparable strength to RMGIs. All nCaF₂ composites had significant F and Ca ion release and ion rechargeability. In F and Ca recharging cycles, PE-nCaF₂ had the highest ion recharging capability among nCaF₂ groups, followed by BT-nCaF₂ and BTM-nCaF₂ (p < 0.05). For all recharge cycles, ion release maintained similar levels, demonstrating long-term ion release was possible. Furthermore, after the final recharge cycle, nCaF₂ nanocomposites provided continuous ion release for 42 days without further recharge.

SIGNIFICANCE

Novel nCaF₂ rechargeable nanocomposites exhibited significant F and Ca ion release over multiple recharge cycles, demonstrating continuous long-term ion release. These nanocomposites are promising restorations with lasting remineralization potential.

A Hydroxypropyl Methylcellulose Film Loaded with AFCP Nanoparticles for Inhibiting Formation of Enamel White Spot Lesions

Objective

This study investigated the effects of mineralizing film consisting of hydroxypropyl methylcellulose (HPMC) and amorphous fluorinated calcium phosphate (AFCP) nanoparticles on enamel white spot lesions (WSLs).

Material and Methods

The AFCP nanoparticles and mineralizing film were prepared via nanoprecipitation and solvent evaporation, respectively. They were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), inductively coupled plasma atomic emission spectrometry (ICP-AES), and fluoride ion selective electrode. Thirty-two human enamel slices (4 mm × 4 mm × 1.5 mm) were highly polished and randomly assigned to four groups: negative control (no treatment); pure HPMC film; mineralizing film; GC Tooth Mousse Plus^® (contains 10% CPP-ACP and 0.2% NaF). Subsequently, samples were challenged by a modified pH-cycling and characterized by color measurement, Micro-CT, SEM/EDX, and nanoindentation.

Results

The mineralizing film could sustain release of Ca, P and F ions over 24 h and maintain AFCP nanoparticles in metastable state over 8~12 h. During 4 weeks of pH cycling, the mineralizing film group exhibited least color change (∆E), mineral loss and lesion depth (120 ± 10 µm) among four groups (p < 0.05). SEM findings revealed that the porosities among enamel crystals increased in negative control and pure HPMC film groups after pH cycling, whereas in mineralizing film group, the original microstructure of enamel was well conserved and mineral deposits were detected between enamel prisms. Mineralizing film group demonstrated a least reduction of nanomechanical properties such as elastic modulus of 77.02 ± 6.84 GPa and hardness of 3.62 ± 0.57 GPa (p < 0.05).

Conclusion

The mineralizing film might be a promising strategy for prevention and management of WSLs via inhibiting enamel demineralization and promoting enamel remineralization.

Effect of Novel Bioactive Glass-Containing Dentin Adhesive on the Permeability of Demineralized Dentin

This study aimed to evaluate the effect of a novel bioactive glass (BAG)-containing dentin adhesive on the permeability of demineralized dentin. Bioactive glass (85% SiO₂, 15% CaO) was fabricated using the sol-gel process, and two experimental dentin adhesives were prepared with 3 wt% silica (silica-containing dentin adhesive; SCA) or BAG (BAG-containing dentin adhesive; BCA). Micro-tensile bond strength (μTBS) test, fracture mode analysis, field-emission scanning electron microscopy (FE-SEM) analysis of adhesive and demineralized dentin, real-time dentinal fluid flow (DFF) rate measurement, and Raman confocal microscopy were performed to compare SCA and BCA. There was no difference in μTBS between the SCA and BCA (p > 0.05). Multiple precipitates were evident on the surface of the BCA, and partial occlusion of dentinal tubules was observed in FE-SEM of BCA-approximated dentin. The DFF rate was reduced by 50.10% after BCA approximation and increased by 6.54% after SCA approximation. Raman confocal spectroscopy revealed an increased intensity of the hydroxyapatite (HA) peak on the dentin surface after BCA application. The novel BAG-containing dentin adhesive showed the potential of both reducing dentin permeability and dentin remineralization.

A modified TEGDMA-based resin infiltrant using polyurethane acrylate oligomer and remineralising nano-fillers with improved physical properties and remineralisation potential

OBJECTIVES

This study aimed to modify an experimental triethylene glycol dimethacrylate (TEGDMA) based resin infiltrant using PUA oligomer and two remineralising fillers, including fluorohydroxyapatite (FHA) and fluoride-doped bioactive glass (FD-BG), to improve the mechanical and physical properties and induce remineralising potential.

MATERIALS AND METHODS

The polyurethane acrylate oligomer (PUA) was synthesised and characterised. Experimental resin infiltrant was prepared by mixing 10% of synthesised PUA with 88% TEGDMA. Water contact angle, penetration coefficient, and penetration depth were then measured. The FHA and FD-BG fillers were synthesised and characterised. To prepare nano-filled resin infiltrant, 5% of each powder was mixed with the prepared resin infiltrant. The prepared resin infiltrants were characterised to evaluate their degree of conversion, mechanical properties, water sorption, and solubility. The ion release of filled resin was also assessed. The non-infiltrated and infiltrated enamel specimens underwent fourteen days of pH-cycling, and a surface microhardness was done to assess the resistance to demineralisation.

RESULTS

The results showed that the addition of PUA to TEGDMA increased the mechanical properties and decreased water sorption and solubility. The addition of synthesised FD-BG fillers to resin infiltrant significantly improved the resistance to demineralisation of enamel samples compared with other groups (p ≤ 0.001). The FHA fillers also improved the resistance to demineralisation; however, the produced changes were not statistically meaningful (p > 0.05).

CONCLUSIONS

Based on the results, the PUA+TEGDMA+ FD-BG/FHA composite can be used as an alternative material for pure TEGDMA in enamel infiltration approaches owing to its better mechanical properties, lower water sorption and solubility, and also remineralisation potential.

CLINICAL SIGNIFICANCE

A resin infiltrant with remineralisation potential, lower water sorption and solubility and higher mechanical properties may enhance the management of early caries lesions.

Effect of Bioactive Glass-Containing Light-Curing Varnish on Enamel Remineralization

This study aimed to evaluate the effect of novel experimental light-curing bioactive glass (BAG)-containing varnish on enamel remineralization. An experimental light-curing, BAG-containing varnish and two commercial varnishes (Nupro White Varnish; Dentsply International, York, PA, USA and Tooth Mousse; GC Corporation, Tokyo, Japan) were used. Microhardness tests (n = 3), field emission scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray spectroscopy (EDS) (n = 5), and X-ray diffraction (XRD) analysis (n = 5) were performed to compare the remineralization effect of three varnishes with and without ultrasonication. The data of microhardness test were analyzed using one-way ANOVA and Tukey's post hoc comparison (P < 0.05). Microhardness of demineralized enamel increased after the application of three varnishes (P < 0.05). The experimental BAG-containing varnish showed the highest microhardness among the three varnishes (P < 0.05). Ultrasonication decreased microhardness of Tooth Mousse and BAG-containing varnish groups (P < 0.05). FE-SEM and XRD revealed precipitates of hydroxyapatite (HAP) or fluorapatite (FAP) crystals of three varnishes. The novel experimental BAG-containing varnish may be a promising clinical strategy for the remineralization of early carious lesions or demineralized enamel surfaces.

Remineralising fluorine containing bioactive glass composites

OBJECTIVES

The objective was to investigate the mechanical properties, fluoride release and apatite formation of resin based dental composites based on a fluoride containing Bioactive Glass (BG) with and without a silylating agent.

METHODS

A SiO₂-P₂O₅-CaO-SrO-Na₂O-CaF₂ BG was synthesized by the melt quench route. This glass and a commercially available inert glass (IG) were incorporated into a light cured BisGMA-TEGMA resin. The composite resins were then evaluated in terms of their ability to form apatite by Fourier Transform Infrared spectroscopy (FTIR) and by scanning electron microscopy (SEM) following immersion in artificial saliva at pH 4 (AS4) and pH 7 (AS7). The experiments were performed with and without silylation of the BG. The compressive strength and flexural strength were determined after 1, 28 and 84 days of immersion in the AS4 and AS7 immersion media.

RESULTS

The FTIR spectra of the BG composites exhibited split bands at approximately 560 and 600 cm^-1 corresponding to a apatite formation in the surface or on the surface under all immersion conditions. SEM showed the presence of a reacted layer of glass particles in the composite surface and the presence of a surface layer of apatite in AS7. The compressive strength and flexural strength were significantly higher for the silylated BG composites. The strengths of both silylated and non silylated BG composites and IG composites decreased upon immersion.

SIGNIFICANCE

BG composites exhibit reduced strengths upon immersion but still exhibit strengths comparable to existing composites after 84 days of immersion.

Evaluation of physico-mechanical properties and filler particles characterization of conventional, bulk-fill, and bioactive resin-based composites

OBJECTIVE

This study evaluated physical and mechanical properties and characterized the filler particles of seven composites.

MATERIALS AND METHODS

Filtek Supreme (FS, 3M Oral Care), Forma (FO, Ultradent), Charisma Diamond (CD, Kulzer), Spectra Smart (SS, Dentsply), Filtek Bulk Fill (FB, 3M Oral Care), Tetric N-Ceram Bulk Fill (TB, Ivoclar), and Cention N (Ivoclar) in self- (CNSC) or dual-curing (CNDC) were evaluated. Fillers size, shape, and content were analyzed by scanning electron microscopy (SEM) and X-ray dispersive energy spectroscopy (EDX). Disk-shaped specimens (n = 5) were prepared for sorption (SP) and solubility (SL). Flexural strength and elastic modulus were tested at 24 h and 12 months (n = 10). Degree of conversion (DC%) and maximum rate of polymerization (Rp^max) were evaluated using micro-Raman spectroscopy. SP and SL results were submitted to Kruskal-Wallis one-way ANOVA and Dunn's pairwise test (α = 0.05). Mechanical properties were analyzed by 2-way ANOVA and Tukey's test (α = 0.05). DC% of CNSC and CNDC was compared by independent t-test (α = 0.05). Rp^max results were analyzed by 1-way ANOVA and Tukey's test (α = 0.05).

RESULTS

The composites differed regarding filler size, shape, and content. CD and CNSC showed lower SP than FS. SS had lower SL than CNSC and CNDC. CNDC presented higher DC% than CNSC. CD, TB, and CNDC showed the highest Rp^max. TB, CNSC, and CNDC showed the lowest 24-h flexural strengths. Mechanical properties of CD did not decrease, while FO, TB, and CNSC showed a significant reduction after storage.

CONCLUSIONS

Monomer composition and fillers characteristics greatly influenced the physico-mechanical properties of the tested composites.

Characterisation of a Bioactive SiO2-CaO-CaF2-Na2O Glass Used in Composites

OBJECTIVES

To characterise the ion release, pH changes and apatite formation of a phosphate free bioactive glass.

METHODS

A SiO₂-CaO-CaF₂-Na₂O glass was synthesized by a melt route with a composition close to the reactive glass in the commercial Cention N® composite. The glass was characterized after immersion in three media: Artificial Saliva pH4 (AS4) Artificial Saliva pH7 (AS7) and in a high phosphate artificial saliva at pH6.5 (AS6.5). The pH and fluoride release were measured using a pH meter and an ion selective electrode. The concentration of Ca, P, Na and Si were measured by ICP-OES. The glass powders after immersion were characterized by FTIR, X-ray powder diffraction and ¹⁹F MAS-NMR.

RESULTS

The glass increased the pH in all three media. Fluoride was detected in all three media but was much higher in AS 6.5. Calcium fluoride formed in AS4 with a small amount of fluorapatite at long immersion times. Fluorapatite and calcium fluoride formed in AS7, whilst in AS6.5 fluorapatite formed. The ion concentrations in solution after immersion reflected the glass composition and the immersion media with fluorapatite being favoured by higher pHs and phosphate contents in the media.

SIGNIFICANCE

The results demonstrated the ability of the glass to increase the pH and to form fluorapatite in phosphate containing media. This may explain the low incidence of secondary caries found in the commercial composite. Unlike the commercial composite evidence was found for the precipitation of fluorite, which will act to reduce the release of fluoride for preventing secondary caries.

Polymerization shrinkage behaviour of resin composites functionalized with unsilanized bioactive glass fillers

Previous work has shown that partial replacement of reinforcing fillers with unsilanized silica particles can diminish polymerization shrinkage stress of dental resin composites. The aim of the present study was to investigate whether such an effect can be attained by using unsilanized bioactive glass (BG). Incorporating BG fillers into resin composites is interesting due to their potential for exerting caries-preventive effects. Experimental light-curable composites with a total filler load of 77 wt% were prepared. Reinforcing fillers were partially replaced with 0-60 wt% of BG 45S5 and an experimental low-sodium fluoride-containing BG. The following properties were investigated: linear shrinkage, degree of conversion, shrinkage stress, maximum shrinkage stress rate, and time to achieve maximum shrinkage stress rate. The diminishing effect of BG 45S5 on shrinkage stress was mediated by a decrease in degree of conversion caused by this BG type. In contrast, as the degree of conversion remained unaffected by the experimental BG, the resulting shrinkage behaviour was governed by the effect of varying amounts of silanized and unsilanized fillers on material's viscoelastic properties. The replacement of silanized reinforcing fillers with unsilanized BG did not reduce polymerization shrinkage stress unless the reduction was attained indirectly through a diminished degree of conversion.

Evaluation of F, Ca, and P release and microhardness of eleven ion-leaching restorative materials and the recharge efficacy using a new Ca/P containing fluoride varnish

OBJECTIVES

The objectives of this study were to evaluate fluoride (F), calcium (Ca), and phosphate (P) release of ion-leaching restorative materials (ILMs), their recharge efficacy with a Ca/P-containing F varnish, and relative microhardness.

METHODS

Thirteen groups of materials were investigated. Cylindrical-shaped specimens were fabricated. Deionised water or lactic-acid solution were used as the storage media. Solutions were changed after 1d, 4d, 7d, and 14d of ion release and at the same periods after recharge with MI Varnish (7 -h storage). F, Ca, and P measurements were accomplished using a fluoride-ion selective electrode, atomic absorption spectrometry, and colourimetric method by spectrophotometer, respectively. Relative Vickers hardness was proceeded with similar specimens used in the F assay (4 periods). SEM/EDS was additionally performed. Statistical analyses were calculated in each parameter (p < 0.05).

RESULT

Hardness of several ILMs immediately increased after recharge. After 28d, Ketac Universal [a high-viscosity glass-ionomer cement (HVGIC)] showed the highest hardness similar to the resin composite control. Although 2 HVGICs (Zirconomer and Equia Forte Fil) ranked as first and second for F release/re-release, some HVGICs had inferior or comparable F capacity to RMGICs (Fuji VIII and Fuji II LC) and a resin-based (RB) ILM (Cention N). Cention N, Activa-Restorative (RB-ILM), and Zirconomer were the top-3 ranking for Ca release/re-release. Activa-Restorative showed the highest P release, whereas Cention N displayed the greatest recharge ability for P.

CONCLUSIONS

Zirconomer showed a versatile performance for ion-release/re-release, especially for F. Cention N had excellent capacity in relation to Ca release and recharge ability of Ca/P.

CLINICAL SIGNIFICANCE

With the F varnish recharge protocol, Zirconomer, Equia Forte, and Fuji VIII seems to have an ability to inhibit initial caries initiation. Cention N is a promising resin-based material that could be an alternative for high caries risk patients due to the high Ca release/recharge with acceptable F release.

Physical Properties of Glass Ionomer Cement Containing Pre-Reacted Spherical Glass Fillers

The aim of this study was to assess the effect of different commercial liquid phases (Ketac, Riva, and Fuji IX) and the use of spherical pre-reacted glass (SPG) fillers on cement maturation, fluoride release, compressive (CS) and biaxial flexural strength (BFS) of experimental glass ionomer cements (GICs). The experimental GICs (Ketac_M, Riva_M, FujiIX_M) were prepared by mixing SPG fillers with commercial liquid phases using the powder to liquid mass ratio of 2.5:1. FTIR-ATR was used to assess the maturation of GICs. Diffusion coefficient of fluoride (DF) and cumulative fluoride release (CF) in deionized water was determined using the fluoride ion specific electrode (n=3). CS and BFS at 24 h were also tested (n=6). Commercial GICs were used as comparisons. Riva and Riva_M exhibited rapid polyacrylate salt formation. The highest DF and CF were observed with Riva_M (1.65x10-9 cm2/s) and Riva (77 ppm) respectively. Using SPG fillers enhanced DF of GICs on average from ~2.5x10-9 cm2/s to ~3.0x10-9 cm2/s but reduced CF of the materials on average from ~51 ppm to ~42 ppm. The CS and BFS of Ketac_M (144 and 22 MPa) and Fuji IX_M (123 and 30 MPa) were comparable to commercial materials. Using SPG with Riva significantly reduced CS and BFS from 123 MPa to 55 MPa and 42 MPa to 28 MPa respectively. The use of SPG fillers enhanced DF but reduced CF of GICs. Using SPG with Ketac or Fuji IX liquids provided comparable strength to the commercial materials.

Zinc-Calcium-Fluoride Bioglass-Based Innovative Multifunctional Dental Adhesive with Thick Adhesive Resin Film Thickness

Apart from producing high bond strength to tooth enamel and dentin, a dental adhesive with biotherapeutic potential is clinically desirable, aiming to further improve tooth restoration longevity. In this laboratory study, an experimental two-step universal adhesive, referred to as Exp_2UA, applicable in both the etch-and-rinse (E&R) and self-etch (SE) modes and combining a primer, containing 10-methacryloyloxydecyldihydrogen phosphate as a functional monomer with chemical binding potential to hydroxyapatite, with a bioglass-containing hydrophobic adhesive resin, was multifactorially investigated. In addition to primary property assessment, including measurement of bond strength, water sorption, solubility, and polymerization efficiency, the resultant adhesive-dentin interface was characterized by transmission electron microscopy (TEM), the filler composition was analyzed by energy-dispersive X-ray spectroscopy, and the bioactive potential of the adhesive was estimated by measuring the long-term ion release and assessing its antienzymatic and antibacterial potential. Four representative commercial adhesives were used as reference/controls. Application in both the E&R and SE modes resulted in a durable bonding performance to dentin, as evidenced by favorable 1 year aged bond strength data and a tight interfacial ultrastructure that, as examined by TEM, remained ultramorphologically unaltered upon 1 year of water storage aging. TEM revealed a 20 μm thick hydrophobic adhesive layer with a homogeneous bioglass filler distribution. Adequate polymerization conversion resulted in extremely low water sorption and solubility. In situ zymography revealed reduced endogenous proteolytic activity, while Streptococcus mutans biofilm formation was inhibited. In conclusion, the three-/two-step E&R/SE Exp_2UA combines the high bonding potential and bond degradation resistance with long-term ion release, rendering the adhesive antienzymatic and antibacterial potential.

Bioactivity and Physico-Chemical Properties of Dental Composites Functionalized with Nano- vs. Micro-Sized Bioactive Glass

Bioactive resin composites can contribute to the prevention of secondary caries, which is one of the main reasons for failure of contemporary dental restorations. This study investigated the effect of particle size of bioactive glass 45S5 on chemical and physical composite properties. Four experimental composites were prepared by admixing the following fillers into a commercial flowable composite: (1) 15 wt% of micro-sized bioactive glass, (2) 15 wt% of nano-sized bioactive glass, (3) a combination of micro- (7.5 wt%) and nano-sized (7.5 wt%) bioactive glass, and (4) 15 wt% of micro-sized inert barium glass. Hydroxyapatite precipitation and pH rise in phosphate-buffered saline were evaluated during 28 days. Degree of conversion and Knoop microhardness were measured 24 h after specimen preparation and after 28 days of phosphate-buffered saline immersion. Data were analyzed using non-parametric statistics (Kruskal-Wallis and Wilcoxon tests) at an overall level of significance of 5%. Downsizing the bioactive glass particles from micro- to nano-size considerably improved their capability to increase pH. The effect of nano-sized bioactive glass on degree of conversion and Knoop microhardness was similar to that of micro-sized bioactive glass. Composites containing nano-sized bioactive glass formed a more uniform hydroxyapatite layer after phosphate-buffered saline immersion than composites containing exclusively micro-sized particles. Partial replacement of nano- by micro-sized bioactive glass in the hybrid composite did not impair its reactivity, degree of conversion (p > 0.05), and Knoop microhardness (p > 0.05). It is concluded that downsizing bioactive glass particles to nano-size improves the alkalizing potential of experimental composites with no negative effects on their fundamental properties.

Acidity-induced release of zinc ion from BioUnionTM filler and its inhibitory effects against Streptococcus mutans

BioUnion filler incorporated into restorative/coating materials is a new bio-functional glass powder. The most unique function of BioUnion filler is its ability to release Zn²⁺ in acidic environments. In this study, the ion release profile of BioUnion filler under acidic conditions and its antibacterial effects against Streptococcus mutans were evaluated. The concentrations of Zn²⁺ released from BioUnion fillers into acetic acids were greater than those released into water. S. mutans inhibition by BioUnion fillers was greater with sucrose than without sucrose, reflecting a decrease in suspension pH in response to the addition of sucrose. Exposure to acids increased Zn²⁺ release from BioUnion fillers, and the fillers after repeated exposure to acids demonstrated inhibitory effects against S. mutans. These findings suggest that BioUnion filler accelerated the release of Zn²⁺ under acidic conditions, which induced bactericidal/inhibitory effects against S. mutans.

Cutting-edge filler technologies to release bio-active components for restorative and preventive dentistry

Advancements in materials used for restorative and preventive treatment is being directed toward "bio-active" functionality. Incorporation of filler particles that release active components is a popular method to create bio-active materials, and many approaches are available to develop fillers with the ability to release components that provide "bio-protective" or "bio-promoting" properties; e.g. metal/calcium phosphate nanoparticles, multiple ion-releasing glass fillers, and non-biodegradable polymer particles. In this review paper, recent developments in cutting-edge filler technologies to release bio-active components are addressed and summarized according to their usefulness and functions, including control of bacterial infection, tooth strengthening, and promotion of tissue regeneration.

Characterization of the bioactivity of two commercial composites

The aim of this study was to characterize the ion release, pH changes and apatite formation ability of two potentially bioactive composites Cention N (CN) and Activa (ACT). Ion release and apatite formation was investigated in three different immersion media: Tris buffer pH 7.3 (TB), Artificial Saliva pH 4 (AS4) and Artificial Saliva pH 7 (AS7) in order to mimic the conditions present in the mouth. Fluoride release was followed using an ion selective electrode, whilst all other ions were determined by inductively coupled plasma optical emission spectroscopy. Apatite formation was followed by FTIR and XRD. SEM was used to follow glass degradation and apatite formation on both polished cross-sections and surfaces of the composites. ACT released very few ions including fluoride upon immersion in TB and AS7, but released more ions including significant quantities of Al in AS4. This would suggest the glasses in ACT are acid degradable fluoro-alumino-silicate glasses similar to the glasses used in glass ionomer cements. There was no evidence of any apatite formation with ACT. CN released more ions in TB and AS7 than ACT and formed an apatite like phase in AS7. The calcium fluoro-silicate glass in CN was observed to degrade significantly in AS4. CN has bioactive properties that may explain the low incidence of secondary caries found clinically with this composite.

Surface roughness and filler particles characterization of resin-based composites

The purpose of this study was to evaluate the surface roughness (Ra), and the morphology and composition of filler particles of different composites submitted to toothbrushing and water storage. Disc-shaped specimens (15 mm × 2 mm) were made from five composites: two conventional (Z100™, and Filtek™ Supreme Ultra Universal, 3M), one "quick-cure" (Estelite ∑ Quick, Tokuyama), one fluoride-releasing (Beautiful II, Shofu), and one self-adhering (Vertise Flow, Kerr) composite. Samples were finished/polished using aluminum oxide discs (Sof-Lex, 3M), and their surfaces were analyzed by profilometry (n = 5) and scanning electron microscopy (SEM; n = 3) at 1 week and after 30,000 toothbrushing cycles and 6-month water storage. Ra data were analyzed by two-way analysis of variance and Tukey's test (α = 0.05). Filler particles morphology and composition were analyzed by SEM and X-ray dispersive energy spectroscopy, respectively. Finishing/polishing resulted in similar Ra for all the composites, while toothbrushing and water storage increased the Ra of all the tested materials, also changing their surface morphology. Beautifil II and Vertise Flow presented the highest Ra after toothbrushing and water storage. Filler particles were mainly composed of silicon, zirconium, aluminum, barium, and ytterbium. Size and morphology of fillers, and composition of the tested composites influenced their Ra when samples were submitted to toothbrushing and water storage.

Randomized investigation of the bioavailability of fluoride in saliva after administration of sodium fluoride, amine fluoride and fluoride containing bioactive glass dentifrices

OBJECTIVES

Bioactive glasses which degrade in aqueous solutions may release bioactive ions such as fluoride (F-) and support fluoride bioavailability in saliva. We investigated how these effects would be apparent in an in vivo experimental trial after toothbrushing in comparison with sodium fluoride and amine fluoride.

MATERIAL AND METHODS

In this single-center, randomized, parallel in vivo trial with a three strata block design, where healthy subjects were randomly assigned into three groups. Each group brushed their teeth either with fluoridated bioactive glass containing dentifrice, with a sodium fluoride (NaF) containing dentifrice or with amine fluoride (AmF) containing toothpaste. Saliva was collected time intervals before, immediately after, 30, 60 and 120 min after toothbrushing. Fluoride concentration was determined in supernatant saliva and salivary sediment using a fluoride ion selective electrode. The data were evaluated statistically using non-parametric tests.

RESULTS

The increase of bioactive fluoride in supernatant saliva was higher after application of NaF or AmF compared to fluoridated bioactive glass. In salivary sediment bioavailability of fluoride lasted longer after application of fluoridated bioactive glass.

CONCLUSIONS

Toothbrushing with the fluoride containing bioactive glass dentifrices had positive effects on the fluoride bioavailability within two hours. Fluoride containing bioactive glass represent a new area for investigation in caries prophylaxis. The bioactive potential impact on the tooth remineralization should be examined further.

TRIAL REGISTRATION

DRKS00016038 .

Novel metformin-containing resin promotes odontogenic differentiation and mineral synthesis of dental pulp stem cells

This represents the first report on the development of metformin-containing dental resins. The objectives were to use the resin as a carrier to deliver metformin locally to stimulate dental cells for dental tissue regeneration and to investigate the effects on odontogenic differentiation of dental pulp stem cells (DPSCs) and mineral synthesis. Metformin was incorporated into a resin at 20% by mass as a model system. DPSC proliferation attaching on resins was evaluated. Dentin sialophosphoprotein (DSPP), dentin matrix phosphoprotein 1 (DMP-1), alkaline phosphatase (ALP), and runt-related transcription factor 2 (Runx2) genes expressions were measured. ALP activity and alizarin red staining (ARS) of mineral synthesis by the DPSCs on resins were determined. DPSCs on metformin-containing resin proliferated well (mean ± SD; n = 6), and the number of cells increased by 4-fold from 1 to 14 days (p > 0.1). DSPP, ALP, and DMP-1 gene expressions of DPSCs on metformin resin were much higher than DPSCs on control resin without metformin (p < 0.05). ALP activity of metformin group was 70% higher than that without metformin at 14 days (p < 0.05). Mineral synthesis by DPSCs on metformin-containing resin at 21 days was 9-fold that without metformin (p < 0.05). A novel metformin-containing resin was developed, achieving substantial enhancement of odontoblastic differentiation of DPSCs and greater mineral synthesis. The metformin resin is promising for deep cavities and perforated cavities to stimulate DPSCs for tertiary dentin formation, for tooth root coatings with metformin release for periodontal regeneration, and for root canal fillings with apical lesions to stimulate bone regeneration.

A Chemical Approach to Optimizing Bioactive Glass Dental Composites

The chemical microenvironment surrounding dental composites plays a crucial role in controlling the bacteria grown on these specialized surfaces. In this study, we report a scanning electrochemical microscopy (SECM)-based analytic technique to design and optimize metal ion-releasing bioactive glass (BAG) composites, which showed a significant reduction in biofilm growth. SECM allows positioning of the probe without touching the substrate while mapping the chemical parameters in 3-dimensional space above the substrate. Using SECM and a solid-state H⁺ and Ca²⁺ ion-selective microprobe, we determined that the local Ca²⁺ concentration released by different composites was 10 to 224 µM for a BAG particle size of <5 to 150 µm in the presence of artificial saliva at pH 4.5. The local pH was constant above the composites in the same saliva solution. The released amount of Ca²⁺ was determined to be maximal for particles <38 µm and a BAG volume fraction of 0.32. This optimized BAG-resin composite also showed significant inhibition of biofilm growth (24 ± 5 µm) in comparison with resin-only composites (53 ± 6 µm) after Streptococcus mutans bacteria were grown for 3 d in a basal medium mucin solution. Biofilm morphology and its subsequent volume, as determined by the SECM imaging technique, was (0.59 ± 0.38) × 10⁷ µm³ for BAG-resin composites and (1.29 ± 0.53) × 10⁷ µm³ for resin-only composites. This study thus lays the foundation for a new analytic technique for designing dental composites that are based on the chemical microenvironment created by biomaterials to which bacteria have been exposed.

A review of bioceramics-based dental restorative materials

Currently, much has been published related to conventional resin-based composites and adhesives; however, little information is available about bioceramics-based restorative materials. The aim was to structure this topic into its component parts and to highlight the translational research that has been conducted up to the present time. A literature search was done from indexed journals up to September 2017. The main search terms used were based on dental resin-based composites, dental adhesives along with bioactive glass and the calcium phosphate family. The results showed that in 123 articles, amorphous calcium phosphate (39.83%), hydroxyapatite (23.5%), bioactive glass (16.2%), dicalcium phosphate (5.69%), monocalcium phosphate monohydrate (3.25%), and tricalcium phosphate (2.43%) have been used in restorative materials. Moreover, seven studies were found related to a newly developed commercial bioactive composite. The utilization of bioactive materials for tooth restorations can promote remineralization and a durable seal of the tooth-material interface.

Mechanical properties of experimental composites containing bioactive glass after artificial aging in water and ethanol

OBJECTIVES

To evaluate the effect of bioactive glass 45S5 (BG) in experimental composites on flexural strength (FS), flexural modulus (FM), modulus of resilience (MR), and material reliability after artificial aging in water for 1, 7, and 30 days, and an additional accelerated aging for 3 days in a 75 vol% ethanol-water solution.

MATERIALS AND METHODS

Five experimental light-curable composites were prepared with 0-40 wt% of BG and a total filler load of 70 wt%. The resinous matrix was Bis-GMA/TEGDMA in 60:40 by weight. Mechanical properties were evaluated using a three-point bending test (ISO/DIN 4049:1998) with n = 20. Weibull statistics were used to assess material reliability. Additionally, the degree of conversion (DC) was assessed 24 h post-cure using FT-Raman spectroscopy.

RESULTS

FS and FM decreased linearly as the amount of BG was increased. The ISO 4049 requirement for a minimum FS of 80 MPa was fulfilled in experimental composites with up to 20 wt% of BG. Degradation of FS and FM with artificial aging was more extensive in materials with higher BG amounts. MR decreased as a function of BG amount and artificial aging. Material reliability (Weibull modulus) was stable through aging for composites with up to 10 wt% of BG. DC was negatively influenced by the BG amount and ranged from 64 to 81%.

CONCLUSION

Increasing the amount of unsilanized BG fillers from 0 to 40 wt% resulted in a progressive decline in mechanical properties and a more extensive degradation during artificial aging.

CLINICAL RELEVANCE

Bioactive fillers diminished the mechanical properties in a dose-dependent manner.

Contraction and Hydroscopic Expansion Stress of Dental Ion-Releasing Polymeric Materials

Ion-releasing polymeric restorative materials seem to be promising solutions, due to their possible anticaries effect. However, acid functional groups (monomers) and glass filler increase hydrophilicity and, supposedly, water sorption. The purpose of the study was to evaluate the influence of water sorption of polymeric materials on the stress state at the restoration-tooth interface. Beautifil Bulk Fill Flow, Beautifil Flow Plus F00, Beautifil Flow F02, Dyract eXtra, Compoglass Flow, Ionosit, Glasiosite, TwinkiStar, Ionolux and Fuji II LC were used for the study. The stress state was measured using photoelastic analysis after: 0.5, 24, 72, 96, 168, 240, 336, 504, 672, 1344 and 2016 h. Moreover, water sorption, solubility and absorption dynamic were assessed. The water sorption, solubility and absorption dynamic of ion-releasing restorative materials are material dependent properties. The overall results indicated that the tested restorative materials showed significant stress decrease. The total reduction in contraction stress and water expansion stress was not observed for materials with low value of water sorption (Beautifil Bulk Fill, Dyract eXtra, Glasionosit and Twinky Star). The photoelastic method turned out to be inadequate to evaluate stress changes of resin modified glass-ionomer cement (RMGI, Fuji II LC and Ionolux).

Real-time Temperature Monitoring During Light-Curing of Experimental Composites

OBJECTIVE

To investigate the real-time temperature rise during light-curing of experimental composite materials containing bioactive glass 45S5 (BG) and compare it to the temperature rise in three commercial composites.

MATERIALS AND METHODS

Five light-curable composite materials containing 0-40 wt% of BG and a total filler load of 70 wt% were prepared. Cylindrical composite specimens 6 mm in diameter and 2 mm thick were cured using Bluephase G2 (Ivoclar Vivadent) at 1200 mW/cm2 for 30 s. The rise in temperature during light-curing was measured at the bottom of the specimens using a T-type thermocouple at the data collection rate of 20 s -1. An additional illumination for 30 s was performed after the specimen temperature returned to the baseline in order to record the temperature rise due to the heating from the curing unit. Statistical analysis was performed using the one-way ANOVA and Pearson correlation analysis with α=0.05.

RESULTS

Temperature rise during light-curing of experimental composites amounted to 12.2-14.0 °C and was comparable to that of the flowable commercial composite (12.5 °C) but higher than that of nano- and micro-hybrid commercial composites (9.6-10.3 °C). The temperature rise during the second illumination was similar for all composites (7.8-9.1 °C). In experimental composites, the temperature rise which was attributable to the polymerization exotherm amounted to 3.1-5.8 °C and was negatively correlated to the BG fraction (R2=0.94). Times at which temperature reached maximum values were in the range of 6.5-19.8 s and were positively correlated to the BG fraction (R2=0.98).

CONCLUSIONS

Temperature rise during light-curing of experimental composites was comparable to that of commercial composites, suggesting that the amount of heat released is tolerable by dental pulp.

Effect of bioactive glass-containing resin composite on dentin remineralization

OBJECTIVES

The purpose of this study was to evaluate the effect of bioactive glass (BAG)-containing composite on dentin remineralization.

METHODS

Sixty-six dentin disks with 3 mm thickness were prepared from thirty-three bovine incisors. The following six experimental groups were prepared according to type of composite (control and experimental) and storage solutions (simulated body fluid [SBF] and phosphate-buffered saline [PBS]): 1 (undemineralized); 2 (demineralized); 3 (demineralized with control composite in SBF); 4 (demineralized with control composite in PBS); 5 (demineralized with experimental composite in SBF); and 6 (demineralized with experimental composite in PBS). BAG65S (65% Si, 31% Ca, and 4% P) was prepared via the sol-gel method. The control composite was made with a 50:50 Bis-GMA:TEGDMA resin matrix, 57 wt% strontium glass, and 15 wt% aerosol silica. The experimental composite had the same resin and filler, but with 15 wt% BAG65S replacing the aerosol silica. For groups 3-6, composite disks (20 × 10 × 2 mm) were prepared and approximated to the dentin disks and stored in PBS or SBF for 2 weeks. Micro-hardness test, attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) and field-emission scanning electron microscopy (FE-SEM) was investigated.

RESULTS

The BAG-containing composite significantly increased the micro-hardness of the adjacent demineralized dentin. ATR-FTIR revealed calcium phosphate peaks on the surface of the groups which used BAG-containing composite. FE-SEM revealed surface deposits partially occluding the dentin surface. No significant difference was found between SBF and PBS storage.

CLINICAL SIGNIFICANCE

Bioactive glass is a potentially useful material for remineralization of tooth structure. When incorporated into a resin composite, it may aid in remineralizing the adjacent demineralized dentin, thus preventing further destruction of the tooth.

CONCLUSION

BAG-containing composites placed in close proximity can partially remineralize adjacent demineralized dentin.

Dentine Tubule Occlusion by Novel Bioactive Glass-Based Toothpastes

There are numerous over-the-counter (OTC) and professionally applied (in-office) products and techniques currently available for the treatment of dentine hypersensitivity (DH), but more recently, the use of bioactive glasses in toothpaste formulations have been advocated as a possible solution to managing DH. Aim. The aim of the present study, therefore, was to compare several bioactive glass formulations to investigate their effectiveness in an established in vitro model. Materials and Methods. A 45S5 glass was synthesized in the laboratory together with several other glass formulations: (1) a mixed glass (fluoride and chloride), (2) BioMinF, (3) a chloride glass, and (4) an amorphous chloride glass. The glass powders were formulated into five different toothpaste formulations. Dentine discs were sectioned from extracted human teeth and prepared for the investigation by removing the cutting debris (smear layer) following sectioning using a 6% citric acid solution for 2 minutes. Each disc was halved to provide test and control halves for comparison following the brushing of the five toothpaste formulations onto the test halves for each toothpaste group. Following the toothpaste application, the test discs were immersed in either artificial saliva or exposed to an acid challenge. Results. The dentine samples were analyzed using scanning electron microscopy (SEM), and observation of the SEM images indicated that there was good surface coverage following artificial saliva immersion. Furthermore, although the acid challenge removed the hydroxyapatite layer on the dentine surface for most of the samples, except for the amorphous chloride glass, there was evidence of tubular occlusion in the dentine tubules. Conclusions. The conclusions from the study would suggest that the inclusion of bioactive glass into a toothpaste formulation may be an effective approach to treat DH.

Nonleachable Imidazolium-Incorporated Composite for Disruption of Bacterial Clustering, Exopolysaccharide-Matrix Assembly, and Enhanced Biofilm Removal

Surface-grown bacteria and production of an extracellular polymeric matrix modulate the assembly of highly cohesive and firmly attached biofilms, making them difficult to remove from solid surfaces. Inhibition of cell growth and inactivation of matrix-producing bacteria can impair biofilm formation and facilitate removal. Here, we developed a novel nonleachable antibacterial composite with potent antibiofilm activity by directly incorporating polymerizable imidazolium-containing resin (antibacterial resin with carbonate linkage; ABR-C) into a methacrylate-based scaffold (ABR-modified composite; ABR-MC) using an efficient yet simplified chemistry. Low-dose inclusion of imidazolium moiety (∼2 wt %) resulted in bioactivity with minimal cytotoxicity without compromising mechanical integrity of the restorative material. The antibiofilm properties of ABR-MC were assessed using an exopolysaccharide-matrix-producing (EPS-matrix-producing) oral pathogen (Streptococcus mutans) in an experimental biofilm model. Using high-resolution confocal fluorescence imaging and biophysical methods, we observed remarkable disruption of bacterial accumulation and defective 3D matrix structure on the surface of ABR-MC. Specifically, the antibacterial composite impaired the ability of S. mutans to form organized bacterial clusters on the surface, resulting in altered biofilm architecture with sparse cell accumulation and reduced amounts of EPS matrix (versus control composite). Biofilm topology analyses on the control composite revealed a highly organized and weblike EPS structure that tethers the bacterial clusters to each other and to the surface, forming a highly cohesive unit. In contrast, such a structured matrix was absent on the surface of ABR-MC with mostly sparse and amorphous EPS, indicating disruption in the biofilm physical stability. Consistent with lack of structural organization, the defective biofilm on the surface of ABR-MC was readily detached when subjected to low shear stress, while most of the biofilm biomass remained on the control surface. Altogether, we demonstrate a new nonleachable antibacterial composite with excellent antibiofilm activity without affecting its mechanical properties, which may serve as a platform for development of alternative antifouling biomaterials.

Antibacterial Properties of Calcium Fluoride-Based Composite Materials: In Vitro Study

The aim of the study was to evaluate antibacterial activity of composite materials modified with calcium fluoride against cariogenic bacteria S. mutans and L. acidophilus. One commercially available conventional light-curing composite material containing fluoride ions (F2) and two commercially available flowable light-curing composite materials (Flow Art and X-Flow) modified with 1.5, 2.5, and 5.0 wt% anhydrous calcium fluoride addition were used in the study. Composite material samples were incubated in 0.95% NaCl at 35°C for 3 days; then dilution series of S. mutans and L. acidophilus strains were made from the eluates. Bacteria dilutions were cultivated on media afterwards. Colony-forming unit per 1 mL of solution (CFU/mL) was calculated. Composite materials modified with calcium fluoride highly reduced (p < 0.001) bacteria growth compared to commercially available composite materials containing fluoride compounds. The greatest reduction in bacteria growth was observed for composite materials modified with 1.5% wt. CaF₂. All three tested composite materials showed statistically greater antibacterial activity against L. acidophilus than against S. mutans.

Mechanical Properties of Calcium Fluoride-Based Composite Materials

Aim of the study was to evaluate mechanical properties of light-curing composite materials modified with the addition of calcium fluoride. The study used one experimental light-curing composite material (ECM) and one commercially available flowable light-curing composite material (FA) that were modified with 0.5–5.0 wt% anhydrous calcium fluoride. Morphology of the samples and uniformity of CaF₂ distribution were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). Mechanical properties were tested after 24-hour storage of specimens in dry or wet conditions. Stored dry ECM enriched with 0.5–1.0 wt% CaF₂ showed higher tensile strength values, while water storage of all modified ECM specimens decreased their tensile strength. The highest Vickers hardness tested after dry storage was observed for 2.5 wt% CaF₂ content in ECM. The addition of 2.0–5.0 wt% CaF₂ to FA caused significant decrease in tensile strength after dry storage and overall tensile strength decrease of modified FA specimens after water storage. The content of 2.0 wt% CaF₂ in FA resulted in the highest Vickers hardness tested after wet storage. Commercially available composite material (FA), unmodified with fluoride addition, demonstrated overall significantly higher mechanical properties.