Is the presence of 10-MDP associated to higher bonding performance for self-etching adhesive systems? A meta-analysis of in vitro studies

Bonding performance of universal adhesive systems to enamel - Effects of the acidic composition

OBJECTIVES

To evaluate the self-etch bonding potential of universal adhesive systems with varying acidic compositions by analyzing the wettability properties, topographical change, and microshear bond strength (µSBS) to enamel.

METHODS

Eight universal adhesives were tested: All-Bond Universal (Bisco), Ambar Universal (FGM), Gluma Bond Universal (Kulzer), OptiBond Universal (Kerr), Peak Universal Bond (Ultradent), Prime&Bond Universal (Dentsply), Singlebond Universal (3 M ESPE), and Tetric N-Bond Universal (Ivoclar). Bovine incisors were prepared and treated with each adhesive according to the manufacturer's instructions. The following tests were carried out: contact angle to measure the adhesives' wetting ability; optical profilometry to evaluate the topographical changes obtained with adhesives' application; energy dispersive X-ray spectroscopy (EDX) to quantify the removal of inorganic elements from enamel; and µSBS to verify the bonding potential of adhesives to enamel. Statistical analyzes included ANOVA, Kruskal-Wallis, Weibull analysis, Pearson correlation, and chi square test (α=0.05).

RESULTS

Significant differences were found in contact angles immediately after adhesive application and after 30 s, with Gluma Bond Universal and Tetric N-Bond Universal showing the lowest (the best wetting ability) and the highest values (the lowest wetting ability), respectively. EDX revealed varying degrees of Ca and P reduction, with Gluma Bond Universal resulting in the greatest Ca and P reduction from enamel (∼65 % and ∼62 % reduction, respectively. Topographical analysis indicated significant changes in roughness, mainly for Gluma Bond Universal. The µSBS mean values ranged from 14.7 MPa (Ambar Universal) to 26.8 MPa (Tetric N-Bond Universal). OptiBond Universal and Tetric N-Bond Universal exhibited the highest resin-enamel bonds. Weibull analysis was performed to better understand the bonding reliability of the tested adhesives, with OptiBond Universal demonstrating increased modulus and characteristic strength, performing as one of the most interesting compositions for enamel bonding. Adhesives based on carboxylic acids were more acidic than adhesives containing phosphate-based monomers (p = 0.033), and the removal of Ca and P elements from enamel was more intense with the use of adhesives based on carboxylic acids (p = 0.029). There was a strong relationship between the Sz values of adhesively treated enamel and the baseline contact angle (wettability) of adhesives (R² = -0.771; p = 0.025).

SIGNIFICANCE

The study highlights significant variability among universal adhesives in terms of their interaction with enamel. Adhesives based on GPDM (OptiBond Universal) and 10-MDP (Tetric N-Bond Universal) demonstrated the best bonding performance, suggesting they may be preferable in clinical settings where strong and reliable enamel bonds are critical. The presence of 10-MDP was not significantly associated with improved dental bonds. The present findings provide valuable information for dentists in selecting adhesives that optimize clinical outcomes in enamel substrate using the self-etching adhesive approach.

The evolution of adhesive dentistry: From etch-and-rinse to universal bonding systems

OBJECTIVES

This review aimed at presenting the mechanisms and pitfalls of adhesion to enamel and dentin, advances in the materials science and in the development of strategies to improve hybrid layer (HL) longevity.

METHODS

Search of the literature was performed on PubMed, Scopus and Web of Science with keywords related to the structure of the dental substrate, HL degradation mechanisms and strategies to contrast them.

RESULTS

Albeit the advances in the dental materials' properties, HL degradation is still a relevant and current issue in adhesive dentistry. However, adhesive materials have become more resistant and less operator sensitive, and good adhesion is currently in the hands of every practitioner. Numerous novel strategies are being developed, able to improve the resistance of adhesive resins to degradation, their ability to infiltrate and chemically bond to dentin, to remove the unbound/residual water within the HL, reinforce the dentin collagen matrix, and inhibit endogenous metalloproteinases. Many of the strategies have turned to nature in search for powerful biomodifying compounds, and for the inspiration as to mimic naturally occurring regenerative processes.

SIGNIFICANCE

Extensive knowledge on the structure of the dental substrate and the complexity of adhesion to dentin has led to the development of improved formulations of dental adhesives and numerous valid strategies to improve the strength and longevity of the HL. Nevertheless, for many of them the road from bench to chairside still seems long. We encourage practitioners to know their materials well and use the strategies readily available to them.

White diet is not necessary during dental bleaching treatment: A systematic review and network meta-analysis of clinical studies

OBJECTIVES

This systematic review with network meta-analysis (NMA) answered whether a white diet is necessary during dental bleaching and if there was any coloring food impacting more significantly the bleaching potential.

DATA SOURCES

The review followed the PRISMA Extension Statement for NMA. Six electronic databases and gray literature were searched until April 2024.

STUDY SELECTION

The eligibility criteria considered clinical trials comparing the bleaching efficacy in participants that followed a white diet (control) and those who had either a supplemented intake of pigments or an unrestricted diet. Risk of bias was assessed using RoB2 (randomized clinical trials/RCT) and ROBINS-I (non-randomized clinical trials/NRCT), and the quality of evidence was checked using GRADE. Color change data were compared using both standard pairwise meta-analysis (SPMA) and Bayesian NMA.

RESULTS

From 1051 records, seven studies were included in the review (four RCT, three NRCT). All studies were classified as having low risk of bias. Regarding NMA, the control group achieved similar color change than the other groups that received pigment supplementation with grape juice, coffee, tea, wine, cola, or an unrestricted diet (p>0.05). The GRADE analysis revealed a moderate quality of evidence.

CONCLUSIONS

The consumption of soft cola, coffee, black tea, grape juice, and red wine, as well as the consumption of a totally unrestricted diet, do not have a significant influence on the effectiveness of bleaching as compared to a white diet regimen.

CLINICAL SIGNIFICANCE

The accumulated evidence suggests that restricting the intake of dietary pigments during dental bleaching is not essential.

Assessment of 10-MDP and GPDM monomers on viability and inflammatory response in human dental pulp stem cells

OBJECTIVES

to assess the cytotoxicity of the following functional monomers used in dental adhesives: 10-Methacryloyloxydecyl dihydrogen phosphate (10-MDP) and glycerol phosphate dimethacrylate (GPDM), and their effect on cytokine release from human dental pulp stem cells (hDPSCs).

METHODS

The hDPSCs cells were isolated from the dental pulp of extracted human third molars. The functional monomers, 10-MDP and GPDM, were diluted in dimethyl sulfoxide (DMSO) at concentrations ranging from 1 to 4 mM. Cells not exposed to the compounds served as controls. The hDPSCs were seeded into 96-well plates and incubated for 48 h. Subsequently, the cells were exposed to 10-MDP and GPDM for 24 h. Then, the culture medium was removed, the mitochondrial metabolism was evaluated using the MTT assay, while cell death analyzed by flow cytometry. Cytokine release (IL-1β, IL-6, IL-8, IL-10, TNF-α) was analyzed by the MAGPIX. The data were analyzed using one-way ANOVA and Tukey's test.

RESULTS

10-MDP demonstrated significant toxicity to hDPSCs, reaching the IC50 at 3 mM. However, its impact on cytokine release was minimal, resulting only in IL-6 and IL-8 levels. GPDM exhibited lower toxicity, even at 4 mM, but induced an increase in IL-1β release and a reduction in IL-6, IL-8, and IL-10 levels, with no effect on TNF-α. Despite the MTT assay results indicating cytotoxicity, the cell death was low for both functional monomers.

SIGNIFICANCE

10-MDP exhibited significant toxicity to hDPSCs, unlike GPDM, however, both monomers resulted in minimal cell death. 10-MDP had a minor impact on cytokine release, whereas GPDM demonstrated a potential to trigger an inflammatory reaction, particularly in the short term.

Different surface treatments and adhesive monomers for zirconia-resin bonds: A systematic review and network meta-analysis

This review examined the efficacy of surface treatments and adhesive monomers for enhancing zirconia-resin bond strength. A comprehensive literature search in PubMed, Embase, Web of Science, Scopus, and the Cochrane Library yielded relevant in vitro studies. Employing pairwise and Bayesian network meta-analyses, 77 articles meeting inclusion criteria were analyzed. Gas plasma was found to be ineffective, while treatments including air abrasion, silica coating, laser, selective infiltration etching, hot etching showed varied effectiveness. Air abrasion with finer particles (25-53 µm) showed higher immediate bond strength than larger particles (110-150 µm), with no significant difference post-aging. The Rocatec silica coating system outperformed the CoJet system in both immediate and long-term bond strength. Adhesives containing 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) were superior to other acidic monomers. The application of 2-hydroxyethyl methacrylate and silane did not improve bonding performance. Notably, 91.2 % of bonds weakened after aging, but this effect was less pronounced with air abrasion or silica coating. The findings highlight the effectiveness of air abrasion, silica coating, selective infiltration etching, hot etching, and laser treatment in improving bond strength, with 10-MDP in bonding agents enhancing zirconia bonding efficacy.

Effectiveness of self-etching bonding systems on dentin after radiotherapy: perspectives on microtensile and microshear bond strength

OBJECTIVE

Self-etching dental adhesives bond with dentin through chemical reactions with calcium. This study assessed bond strength (BS) using microtensile (µTBS) and microshear (µSBS) tests on sound and post-radiotherapy dentin, with dental adhesives containing different functional monomers.

METHODS

Sound dentin (SD) and post-radiotherapy irradiated dentin (ID) were tested with two adhesive systems: Clearfil SE Bond (SE, 10-MDP-based) and FL Bond II (FL, containing carboxylic and phosphonic monomers with S-PRG bioactive particles). The tests occurred initially (24 h) and six months later; fracture mode was also analyzed (40x). Ninety-six human molars were randomly assigned (n = 12), and half were irradiated with a 70 Gy radiation dose. For µTBS test, teeth were bonded, restored and sectioned them into beams (0.64 mm2). The µSBS test used filled transparent cylindrical matrices with resin composite and light-cured them after dental adhesive applications. Three-way ANOVA and Tukey's test (p < 0.05) analyzed the data.

RESULTS

µTBS showed a significant substrate x adhesive interaction (p < 0.001), while µSBS was significant for all factors (p = 0.006). SE and FL performed better on SD and ID, respectively, in the µTBS test. As for µSBS, SE showed higher values on ID (p < 0.05). Lower BS values occurred for SD-FL and ID-SE after six months.

CONCLUSION

Dental adhesive performance varied based on substrate type and test method. FL was more stable for ID in µTBS, while SE excelled in µSBS.

CLINICAL RELEVANCE

As post-radiotherapy irradiated dentin becomes more vulnerable, self-etching systems based on functional monomer and bioactive ingredients may exhibit appropriate bonding to this altered substrate.

Which Whitening Mouthwash With Different Ingredients Is More Effective on Color and Bond Strength of Enamel?

OBJECTIVE

To examine the effects of six whitening mouthwashes on tooth color and immediate bond strength to the enamel.

MATERIALS AND METHODS

Human incisors were divided into seven groups (n = 10) according to mouthwashes (R.O.C.S Black Edition White, Splat White Plus, Colgate Plax White Charcoal, Signal White Now, Listerine Advanced White, Colgate Optic White, and distilled water). After the initial color measurements, the teeth were exposed to mouthwash for 4 weeks. Then, the color measurements were repeated. Then, cylindrical composite resin blocks were immediately applied to the enamel surfaces and subjected to shear bond strength tests. Data were analyzed using Kruskal-Wallis and Bonferroni tests (α = 0.05).

RESULTS

Δ𝑏, Δ𝐿, and ΔE00 values did not present significant differences among the groups. Significant differences among the groups were determined for Δ𝑎 and ΔWID values (p < 0.05). R.O.C.S Black Edition White and Splat White Plus produced clinically acceptable color changes. Signal White Now, Splat White Plus, and Listerine Advanced White created acceptable whiteness changes. The mouthwashes did not statistically affect the bond strength compared to the distilled water (p > 0.05).

CONCLUSIONS

Whitening mouthwash containing blue covarine revealed more acceptable color and whitening changes. Mouthwash containing charcoal led to the lowest enamel bond strength values.

CLINICAL SIGNIFICANCE

The content of whitening mouthwashes affected the degree of tooth whitening and shear bond strength to enamel.

Effect of double adhesive layer application on micro-tensile dentin bond strength of a universal adhesive

Introduction

Achieving optimal dentin bond strength is crucial for the long-term success of adhesive restorations. This study aims to evaluate the impact of double adhesive layer application, with and without light curing between applications, on the micro-tensile dentin bond strength (µ-TBS) of a universal adhesive, in comparison to the conventional single-layer application.

Methods

Intact human molars were divided into three groups (n = 15) according to the adhesive application technique using a universal self-etch adhesive (Tetric N-Bond Universal, Ivoclar) as follows: (1) according to the manufacturer's instructions, (2) double-layer application without light curing between layers, and (3) double-layer application with light curing between layers. Samples were immediately tested for µ-TBS, with failure types recorded as adhesive, cohesive, or mixed. Representative samples were observed by scanning electron microscopy. Data were analyzed using multiple-way ANOVA (α = 0.05).

Results

The double adhesive layer with and without light curing between layers showed similar μ-TBS to that of the control group (p > 0.05).

Discussion

From a clinical perspective, these findings suggest that the accurate application of a single layer of a universal adhesive can be as effective as more complex techniques. Additionally, the use of universal bonding agents may have contributed to the outcomes observed in this study. In conclusion, double adhesive layer application and light curing between adhesive layers did not increase the µ-TBS with the universal adhesive agent explored.

Stability of the Dentin-Bonded Interface Using Self-Etching Adhesive Containing Diacrylamide after Bacterial Challenge

Purpose/Aim: Acrylamides are hydrolytically stable at pH lower than 2, and were shown to preserve bonded interface integrity with two-step, total etch adhesives. The objective of this study was to leverage those two characteristics in self-etching primers containing the acidic monomer 10-MDP and test the microtensile bond strength before and after incubation with S. mutans incubation. Materials and Methods: Acidic primers (10 wt % 10-methacryloyloxydecyl dihydrogen phosphate─10-MDP; 45 wt % N,N-diethyl-1,3-bis(acrylamido)propane─DEBAAP, or 2-hydroxyethyl methacrylate─HEMA; 45 wt %, glycerol-dimethacrylate─GDMA) and adhesives (DEBAAP or HEMA/10-MDP/UDMA 45/10/45 wt %) were made polymerizable by the addition of 0.2 wt % camphorquinone, 0.8 wt % ethyl-4-dimethylaminobenzoate, 0.4 wt % diphenyliodonium hexafluorophosphate, and 0.1 wt % butylhydroxytoluene. Nonsolvated materials were characterized for flexural strength (FS), modulus (E), toughness, water sorption/solubility (WS/SL), contact angle, and vinyl conversion (DC). Viscosity was evaluated after adding 20 and 40 vol % ethanol to the primer and adhesive, respectively. The experimental materials or Clearfil SE Bond (CC─commercial control) were used to bond a commercial composite (Filtek Supreme) to the flat surface of human dentin. Microtensile bond strength (MTBS) was tested in 1 mm2 sticks for the 5 primer/bond combinations: CC (Clearfil Bond Primer and Bond), HH (HEMA/HEMA), DD (DEBAAP/DEBAAP), HD (HEMA/DEBAAP), and DH (DEBAAP/HEMA). Prior to testing, sticks were stored in water or biofilm-inducing culture medium with S. mutans for 1 week. Confocal images and FTIR-ATR evaluation evaluated the hybrid layer of the adhesives. Results were analyzed using Student's t-test (WS, SL, DC, contact angle, FS, E, toughness), one-way ANOVA/Tukey's test for viscosity, and two-way ANOVA/Tukey's test for MTBS (95%). Results: HEMA-based materials had lower contact angle (p = 0.004), higher WS (p < 0.001), and similar SL values compared to DEBAAP (p = 0.126). FS (p = 0.171) and E (p = 0.065) dry values were similar, but after one week of water storage, FS/E dropped more significantly for HEMA materials. Dry and wet toughness was greater for DEBAAP (p < 0.001), but it also had the greatest drop (46%). Clearfil bonds had the highest viscosity, followed by DEBAAP and HEMA, respectively (p = 0.002). For the primers, HEMA had the lowest viscosity (p = 0.003). As far as MTBS, all groups tested in water were statistically different when compared with HH (p < 0.001). After storage in biofilm, DH had the highest MTBS value, being statistically different from HH (p = 0.002), CC (p = 0.015), and DD (p = 0.027). Conclusions: The addition of a diacrylamide and its association with HEMA in self-etching adhesive systems provided greater bonding stability after bacterial challenge.

Shear Bond Strength of Self-Adhesive Versus Conventional Flowable Composites: An In Vitro Study

Aim

As an emerging yet underexplored innovation in dentistry, self-adhesive flowable composites (SAFCs) represent a promising and enduring advancement in the dental material technology. Our study aims to evaluate the shear bond strength of two SAFCs and the bonding of conventional flowable composite (CFC) to permanent dentin.

Materials and Methods

Thirty-six teeth were embedded in acrylic blocks, with the occlusal third removed to expose the underlying dentin. A cylindrical mold was positioned on the treated dentin surface and filled with the composite resin material to be evaluated. The prepared permanent dentin surfaces were randomly assigned to three groups based on the following application protocols: Group 1: Axo Uni Flow (AXIMACK, India); Group 2: Constic (DMG, Germany); and Group 3: 37% phosphoric acid etchant + Single Bond Universal + Filtek Z350 XT (3M ESPE, USA). The shear bond strength of the prepared specimens was measured by using a universal testing machine. The data were analyzed with Kruskal-Wallis one-way analysis of variance, followed by Dwass-Steel-Critchlow-Fligner pairwise comparisons.

Results

Filtek Z350 XT (3M ESPE, USA) demonstrated higher shear bond strength values when compared to Constic (DMG, Germany) and Axo Uni Flow (AXIMACK, India). A significant difference was found between these materials. However, the shear bond strength of the two SAFCs tested did not differ significantly.

Conclusion

The investigation's findings suggest that the SAFCs exhibited inferior shear bond strength compared with CFCs when bonded with permanent dentin.

Dentin Bonding Durability of Four Different Recently Introduced Self-Etch Adhesives

The objectives of this study were to evaluate the bonding durability of four different self-etch adhesives to dentin after 24 h and thermal cycling (TC) and to measure the degree of polymerization conversion (DC) in situ. Two-step self-etch adhesives, Clearfil SE Bond 2 (SE2, Kuraray Noritake Dental) and G2-Bond Universal (G2B, GC), and one-step self-etch adhesives, Scotchbond™ Universal Plus Adhesive (SBU, 3M ESPE) and Clearfil Universal Bond Quick (UBQ, Kuraray Noritake Dental), were used. The labial surfaces of bovine teeth were ground to create flat dentin surfaces. The adhesives were applied according to the manufacturers' instructions. After resin composite buildup and 24 h water storage, the specimens were sectioned into beams and all groups were subjected to thermal stress for 0, 10,000 (10k), or 20,000 (20k) cycles followed by micro-tensile bond strength (µTBS) testing. In situ DC was investigated with a laser Raman microscope. The µTBS data were statistically analyzed and subjected to a Weibull analysis. The different groups were compared at the characteristic strength (63.2% probability of failure) (α = 0.05). Two-Way ANOVA was used to show the effect of different adhesives and thermal cycling on the mean DC% followed by Tukey's multiple comparison post hoc test. G2B/TC10k resulted in a significant increase in the µTBS compared to TC0. SBU/TC20k showed significantly higher µTBS compared to TC0. For comparison between different tested adhesives, SBU showed a significantly lower µTBS compared to G2B after TC10k. G2B and SBU showed a greater number of adhesive failures after TC. Mean DC% was different for each adhesive. The newly developed MDP- and HEMA-free 2-SEA showed similar bonding performance with the gold-standard 2-SEA. However, there is still room for further improvement in terms of SEAs.

The influence of neutral MDP-Na salt on dentin bond performance and remineralization potential of etch-&-rinse adhesive

OBJECTIVES

To investigate the effect of neutral 10-methacryloyloxydecyl dihydrogen phosphate salt (MDP-Na) on the dentin bond strength and remineralization potential of etch-&-rinse adhesive.

METHODS

Two experimental etch-&-rinse adhesives were formulated by incorporating 0 wt% (E0) or 20 wt% (E20) neutral MDP-Na into a basic primer. A commercial adhesive, Adper Single Bond 2 (SB, 3 M ESPE), served as the control. Sixty prepared teeth were randomly allocated into three groups (n = 20) and bonded using either one of the experimental adhesives or SB. Following 24 h of water storage, the bonded specimens were sectioned into resin-dentin sticks, with four resin-dentin sticks obtained from each tooth for microtensile bond strength (MTBS) test. Half of the sticks from each group were immediately subjected to tensile loading using a microtensile tester at a crosshead speed of 1 mm/min, while the other half underwent tensile loading after 6-month incubation in artificial saliva (AS). The degree of conversion (DC) of both the control and experimental adhesives (n = 6 in each group) and the adsorption properties of MDP-Na on the dentin organic matrix (n = 5 in each group) were determined using Fourier-transform infrared spectrometry. Furthermore, the effectiveness of neutral MDP-Na in promoting the mineralization of two-dimensional collagen fibrils and the adhesive-dentin interface was explored using transmission electron microscopy and selected-area electron diffraction. Two- and one-way ANOVA was employed to assess the impact of adhesive type and water storage on dentin bond strength and the DC (α = 0.05).

RESULTS

The addition of MDP-Na into the primer increased both the short- and long-term MTBS of the experimental adhesives (p = 0.00). No difference was noted in the DC between the control, E0 and E20 groups (p = 0.366). The MDP-Na remained absorbed on the demineralized dentin even after thorough rinsing. The intra- and extra-fibrillar mineralization of the two-dimensional collagen fibril and dentin bond hybrid layer was confirmed by transmission electron microscopy and selected-area electron diffraction when the primer was added with MDP-Na.

CONCLUSIONS

The use of neutral MDP-Na results in high-quality hybrid layer that increase the dentin bond strength of etch-&-rinse adhesive and provides the adhesive with remineralizing capability. This approach may represent a suitable bonding strategy for improving the dentin bond strength and durability of etch-&-rinse adhesive.

Touch-cure activation by marketed universal resin luting cements of their associated primer to dentin

PURPOSE

The aim of this study was to investigate the dentin shear bond strength (SBS) and bonding interface of three recently developed "universal" resin luting cements based on different modalities.

METHODS

The dentin SBS and interfacial analysis of three recently launched "universal" resin luting cements, namely, G-Cem One, RelyX Universal and Panavia SA cement universal, were studied. All bonding protocols, including the previous use of their dedicated primer or universal adhesive in touch-cure mode or light-cure mode were performed. Variolink Esthetic LC used in conjunction with Scotchbond Universal Plus was used as a control group. For each group (n = 9), 10 specimens were tested for dentin SBS and two were examined by scanning electron microscopy. SBS were analyzed by two-way ANOVA followed by Dunnett's test.

RESULTS

SBS values showed that the three "universal" resin luting cements tested exhibit different adhesive behaviors. G-Cem One with its touch-cure activated primer had a greater SBS to dentin (25.5 MPa) than that of the control group (22.1 MPa).

CONCLUSION

"Universal" resin luting cements have variable efficacy when used in self-curing mode. The touch-curing mode is also of concern but may show high potential for some formulations.

New Monomer Capable of Dual Chemical Binding with Dentin to Improve Bonding Durability

The water-rich nature of the dentin bonding microenvironment, coupled with the stresses on the bonding interface, contributes to the hydrolytic degradation of the hybrid layer, resulting in a decline in bonding durability and, ultimately, restoration failure. Currently, the 3-step etch-and-rinse technique remains the gold standard for dentin bonding, and the bonding mechanism mainly involves a physical interaction with little chemical bonding. In this study, we have developed a siloxane-modified polyurethane monomer (SPU) with acrylate and siloxane modifications that chemically binds to both collagen and hydroxyapatite in dentin. Formulated as a bisphenol A-glycidyl methacrylate alternative, the SPU monomer-based adhesive was designed to improve dentin bonding quality and durability. Attenuated total reflection Fourier transform infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscope, and hydroxyproline release assays were performed on SPU-treated collagen, hydroxyapatite, and acid-etched dentin slices to dentin. The physicochemical properties of the configured SPU adhesives were profiled for polymerization behavior, water contact angle, and tensile strain and strength. The bonding effectiveness was assessed through micro-tensile strength, nano-leakage tests conducted on the bonded samples before and after thermal cycle aging. Finally, we further conducted in vivo and in vitro experiments to assess the biocompatibility of adhesives. The results showed that the siloxane groups of SPU monomer could covalently bind to dentin collagen and hydroxyapatite. The incorporation of SPU in the adhesive led to a significant increase in adhesive polymerization (P < 0.05) and tensile strain at break up to 134.11%. Furthermore, the SPU adhesive significantly improved dentin bond strength (P < 0.05), reduced interfacial nano-leakage (P < 0.05), and displayed good biocompatibility. In conclusion, the application of SPU, which achieves dual chemical bonding with dentin, can improve the quality of the hybrid layer, buffer the interfacial stresses, enhance the interfacial resistance to hydrolysis, and provide a feasible strategy to extend the service life of adhesive restorations.

Evaluation of Shear Bond Strengths of 3D Printed Materials for Permanent Restorations with Different Surface Treatments

The development of high-filled 3D printing resin necessitates a bonding protocol for dental indirect restorations to achieve optimal bond strength after cementation. This study evaluates shear bond strengths of high-filler 3D printed materials for permanent restorations with various surface treatments. Rodin Sculpture 1.0 (50% lithium disilicate fillers) and 2.0 Ceramic Nanohybrid (>60% zirconia and lithium disilicate fillers) were tested, with Aelite All-Purpose Body composite resin as control. Samples were prepared, post-cured, and sandblasted with alumina (25 µm). Surface roughness was analyzed using an optical profilometer. Two bonding protocols were compared. First, groups were treated with lithium disilicate silane (Porcelain Primer) or zirconia primer (Z-Prime Plus) or left untreated without a bonding agent. Beam-shaped resin cement (DuoLink Universal) specimens were bonded and stored in a 37 °C water bath. Second, additional sets of materials were coated with a bonding agent (All-Bond Universal), either followed by silane application or left untreated. These sets were then similarly stored alongside resin cement specimens. Shear bond tests were performed after 24 h. SEM images were taken after debonding. One-Way ANOVA and post hoc Duncan were performed for the statistical analysis. Rodin 1.0 exhibited increased adhesive failure with silane or zirconia primer coating, but significantly improved bond strengths with bonding agent application. Rodin 2.0 showed consistent bond strengths regardless of bonding agent application, but cohesive failure rates increased with bonding agent and filler coating. In all groups, except for Rodin 1.0 without bonding agent, silane coating increased cohesive failure rate. In conclusion, optimal shear bond strength for high-filler 3D printing materials can be achieved with silane coating and bonding agent application.

Shear bond strength of universal adhesives to human enamel and dentin

OBJECTIVE

The composition of universal adhesives is highly diverse. The purpose of this in vitro study was to compare the shear bond strength of a composite with five different universal adhesives to human enamel and dentin.

MATERIALS AND METHODS

The shear bond strength of a composite (G-aenial Universal Injectable) to human enamel and dentin was tested in selective enamel etching mode before and after thermocyclic aging (10,000 cycles) using five different universal adhesive systems (Adhese Universal VivaPen, Clearfil Universal Bond Quick, G-Premio Bond, Prime&Bond active, and Scotchbond Universal Plus). Two-bottle systems (OptiBond FL and G2-Bond Universal) were used as control. Scanning electron microscopy was conducted of the bonding interface.

RESULTS

Significant differences in shear bond strength values were found among the five evaluated universal adhesives. Lowest shear bond strength values were observed for 2-hydroxyethylmethacrylate (HEMA)-free systems. Thermocyclic aging did not significantly reduce shear bond strength values indicating that the initial bond remains stable.

CONCLUSIONS

The clinical use of universal adhesives Adhese Universal VivaPen, Clearfil Universal Bond Quick, and Scotchbond Universal Plus can be encouraged as they provided comparable or even better shear bond strength values than the two-bottle controls.

CLINICAL SIGNIFICANCE

Universal adhesives that were developed for the same indication and approved for clinical use demonstrated variety in shear bond strength values. When applied in the selective enamel etching mode, a stable bond can be expected from adhesives containing HEMA and monomers with phosphate groups.

Compatibility versus reaction diffusion: Factors that determine the heterogeneity of polymerized adhesive networks

OBJECTIVES

Heterogeneity and phase separation during network polymerization is a major issue contributing to the failure of dental adhesives. This study investigates how the ratio of hydrophobic crosslinkers to hydrophilic comonomer (C/H ratio), as well as cosolvent fraction (ethanol/water) influences the degree of heterogeneity and proclivity for phase separation in a series of model adhesive formulations.

METHODS

Twelve formulations were investigated, with 4 different C/H ratios (7:1, 2.2:1, 1:1, 0.5:1) and 3 different overall cosolvent fractions (0, 10 and 20 wt%). The heterogeneity and phase behavior were characterized using Fourier Transform Infrared Spectroscopy (FT-IR), dynamic mechanical analysis (DMA), small-angle x-ray scattering (SAXS) and atomic force microscopy (AFM).

RESULTS

In resins without cosolvent, all characterizations confirm reduced heterogeneity as C/H ratio decreases. However, when 10 or 20 wt% of cosolvent is included in the adhesive formulation, a higher degree of heterogeneity and even distinct phase separation with domains ranging from a few hundreds of nanometers to a few micrometers in size form. This is particularly noticeable at lower C/H ratios, which is surprising as HEMA is commonly considered a compatibilizer between hydrophobic crosslinkers and aqueous (co)solvents.

SIGNIFICANCE

Our experiments demonstrate that formulations with lower C/H ratio and thus a lower viscosity experience later onsets of diffusion limitations during polymerization, which favors thermodynamically driven phase separation. Therefore, to determine or predict the resulting phase structure of adhesive materials, it is necessary to consider the kinetics and diffusion constraints during the formation of the polymer network and not just the compatibility of resin constituents.

Effect of Simulated Dental Pulpal Pressure Using Fetal Bovine Serum for the Bonding Performance of Contemporary Adhesive to Dentin

This study evaluated the effect of simulated pulpal pressure (SPP) conditions and storage time on contemporary adhesive systems' microtensile bond strength (µTBS) to dentin. Extracted human molars were prepared and randomly divided into four groups according to the adhesives: Clearfil Megabond 2 (CSE), Beautibond Xtreme Universal (BXU), G2-Bond (G2B), and Scotchbond Universal Plus (SBP). Each adhesive group was further divided following the SPP conditions: control with no simulation (SPP-CTR), SPP with distilled water (SPP-DTW), and SPP with fetal bovine serum (SPP-FBS). Resin composite build-ups were prepared, and teeth were stored in water (37 °C) for 24 h (24 h) and 3 months (3 m). Then, teeth were sectioned to obtain resin-dentin bonded beams and tested to determine the µTBS. Data were analyzed using three-way ANOVA, Tukey post hoc tests (=0.05), and Weibull failure analysis. Failure mode was observed using scanning electron microscopy. The µTBS response was affected by adhesive systems, simulated pulpal pressure conditions, and storage time. SPP-CTR groups presented a higher overall bond strength than SPP-DTW and SPP-FBS, which were not significantly different from each other. Only for SBP, the SPP-FBS group showed higher µTBS than the SPP-DTW group. The Weibull analysis showed that the bonding reliability and durability under SPP-DTW and SPP-FBS were inferior to SPP-CTR, and the 24 h bonding quality of adhesives to dentin was superior to that of 3 m. SPP drastically reduced the µTBS of all adhesives to dentin regardless of solution (distilled water or fetal bovine serum). Storage after 3 m also decreased µTBS despite the SPP condition.

Dentin adhesion of bulk-fill composites and universal adhesives in class I-cavities with high C-factor

OBJECTIVES

The aim of this study was to compare the dentin adhesion of bulk-fill composites in high C-factor class I-cavities before and after thermocycling to a control group using incremental layering technique.

METHODS

A standardized class I-cavity was prepared into 195 human molars, then different universal adhesives were applied either in self-etch or etch & rinse mode, and the cavity was filled according to each materials application protocol. The material combinations used were a conventional layered composite as control, the respective bulk-fill product, two other bulk-fill composites made by different manufacturers, with one of them being tested using two different polymerization times. Furthermore, one thermoviscous bulk-fill composite and one self-adhesive restorative were examined of which the latter can only be applied in self-etch mode. In each group the dentin adhesion to the cavity bottom was measured using microtensile bond strength test initially (24 h water storage) and after thermocycling. All results were statistically analyzed using STATA 17.0.

RESULTS

The statistical analysis showed significant differences between the control and the experimental groups (p < 0.001). The highest mean bond strength before (14.8 ± 10.7 MPa) and after aging (14.2 ± 11.5 MPa) was measured for the etch & rinse-control group. Among the bulk-fill groups, the etch & rinse technique consistently showed higher bond strengths. Bond strength of groups with shortened polymerization did not exceed 2.1 MPa. The bond strength of the self-adhesive restoration material was low before and after thermocycling (2.7 MPa/ 0.0 MPa). Groups with low bond strength values showed a high number of pre-testing-failures.

CONCLUSIONS

Bulk-fill materials used in high C-factor class I-cavities showed lower bond strength during self-etch application. The same applies for a shortened polymerization regime, which cannot be recommended for high C-factor cavities.

CLINICAL SIGNIFICANCE

Today, a large variety of materials and application techniques can be used when placing an adhesive restoration. Whether new instead of established procedures should be applied in high C-factor cavities has to be critically assessed, as they are a demanding scenario for adhesive restorations.

Dentin surface modification by MDP to improve dentin bonding stability: Topological enhancement and mineralization of collagen structure in hybrid layers

Decades of research have been conducted on 10-Methacryloyloxydecyl dihydrogen phosphate (MDP) through numerous studies. The mechanisms by which its residual calcium salts benefit dentin bonding remain undetermined. The objective of the research was to investigate the role and process of remaining calcium salts in the priming procedure and their capacity for remineralization. The investigation focused on the variations in topological structure, mechanical properties, and chemical interactions between the main agent and the dentin surface. Two adhesive modes including prime-and-rinse(P&R) and prime-and-nonrinse (P&NR) utilized to evaluate the bonding performance and remineralization ability. The findings indicated that both P&R and P&NR methods could eliminate the smear-layer, uncover dentinal-tubules, and generate a textured/rough surface on the dentin. Collagen fibrils exhibited a greater presence of inorganic minerals in the P&NR mode. Compared to control group, both P&R and P&NR groups improved immediate and aging bond strength significantly (P < 0.05). AFM and 3D-STORM revealed MDP and its residual calcium salts distributed in collagen fibrils and expanded collagen matrix. In the P&NR group, TEM revealed that the dentin collagen matrix experienced some remineralization, and there was also mineralization within the collagen fibrils embedded in the bonding interface. Thus, MDP priming improved dentin bonding stability. Residual calcium salts of P&NR process can enhance topological structure of the collagen matrix and induce intrafibrillar mineralization.

A glycol chitosan derivative with extrafibrillar demineralization potential for self-etch dentin bonding

OBJECTIVES

Extrafibrillar demineralization is an etching technique that removes only minerals from around the collagen fibrils for resin infiltration. The intrafibrillar minerals are left intact to avoid their replacement by water that is hard for adhesive resin monomers to displace. The present work reported the synthesis of a water-soluble methacryloyloxy glycol chitosan-EDTA conjugate (GCE-MA) and evaluated its potential as an extrafibrillar demineralization agent for self-etch dentin bonding.

METHODS

Glycol chitosan-EDTA was functionalized with a methacryloyloxy functionality. Conjugation was confirmed using Fourier transform-infrared spectroscopy. The GCE-MA was used to prepare experimental self-etch primers. Extrafibrillar demineralization of the primers was evaluated with scaning electron microscopy and transmission electron microscopy. The feasibility of this new self-etch bonding approach was evaluated using microtensile bond strength testing and inhibition of dentin gelatinolytic activity. The antibacterial activity and cytotoxicity of GCE-MA were also analyzed.

RESULTS

Conjugation of EDTA and the methacryloyloxy functionality to glycol chitosan was successful. The functionalized conjugate was capable of extrafibrillar demineralization of mineralized collagen fibrils. Tensile bond strength of the experimental self-etch primer to dentin was comparable to that of phosphoric acid-etched dentin and the commercial self-etch primer Clearfil SE Bond 2. The GCE-MA also inhibited soluble rhMMP-9. In-situ zymography detected minimal fluorescence in hybrid layers conditioned with the experimental primer. The GCE-MA was noncytotoxic and possessed antibacterial activities against planktonic bacteria.

SIGNIFICANCE

Synthesis of GCE-MA brought into fruition a self-etch conditioner that selectively demineralizes the extrafibrillar mineral component of dentin. A self-etch primer prepared with GCE-MA achieved bond strengths comparable to commercial reference adhesive systems.

Influence of Application Modes on Increasing Bond Strength Longevity of Self-etching and Universal Adhesive Systems to Enamel

The present study aimed to evaluate the influence of application mode on the short-term microshear bond strength longevity of self-etching and universal adhesive systems to enamel, the failure mode, and the resulting enamel surface micromorphology. Ninety enamel surfaces were obtained from sound third molars, planed, and randomly assigned to nine groups, according to the application mode and the adhesive system (n=10). There were three primer application modes: according to the manufacturer's recommended application time (control), using double the application time recommended for the primer and selective enamel etching. The adhesive systems used were: Clearfil SE Bond (Kuraray), FL-Bond II (SHOFU), and Futurabond U (Voco). At least two resin-bonded composite cylinders (Grandioso Light Flow, Voco) were placed on each enamel surface, and then evaluated for microshear bond strength at 24 hours and 180 days of storage in solution body fluid (SBF) at pH 7.4. Failure modes were evaluated with a stereoscopic microscope at 20× magnification. A micromorphological analysis of the enamel surface was performed under a scanning electron microscope at 5000× magnification before and after the treatments. Mixed models for repeated measures over time showed significant interaction among application modes, adhesive systems, and time periods (p=0.0331). The bond strength of FL-Bond II adhesive to enamel observed after performing selective enamel etching was significantly higher than that observed after applying the control treatment (p=0.0010) at both 24 hours and 180 days. However, no significant difference was observed between the application of this same adhesive at double the time recommended by the manufacturer and the other two application modes (p>0.05). There was also no significant difference in the microshear bond strength for the enamel treatments applied using Clearfil SE Bond and Futurabond U (p>0.05). A significant reduction in bond strength to enamel was observed at the 180-day storage time for all the adhesive systems when selective enamel etching was performed (p<0.0001). No significant association was observed between the adhesive system failure mode and the enamel treatments (p=0.1402 and p=0.7590 for 24 hours and 180 days, respectively). The most prevalent failure was the adhesive type.

Does aPDT reduce bacterial load in endodontic infected teeth? A systematic review and meta-analysis

This systematic review investigated whether antimicrobial photodynamic therapy (aPDT) after chemomechanical root canal disinfection (CD) yields a greater microbial load reduction than only CD. An electronic literature search was conducted on four databases up to November 2022, with no language or publication date restrictions. Randomized and non-randomized clinical trials were included if participants had a primary endodontic infection in permanent teeth, and if microbial loads before and after using aPDT were compared. Two researchers independently screened titles and abstracts to determine study eligibility. Assessments included risk of bias and methodological quality. This review was registered in PROSPERO (CRD42020181783). Eight studies were included in the qualitative analysis, and six were eligible for meta-analysis. In the random effects model, aPDT significantly improved the results of root canal disinfection when compared with standard protocols for cleaning and shaping (p = 0.04, 95% CI -1.72, -0.05). Subgroup analysis suggested that aPDT has a better effect on reducing the load of anaerobic microorganisms (p = 0.003, 95% CI -3.36, -0.69). The use of aPDT as an adjunct to chemomechanical disinfection promotes additional reduction of the microbial load and, therefore, seems to improve the results of root canal treatments in permanent teeth with a primary endodontic infection. However, certainty of evidence should be improved.

Effects of Short-Term Exposure of Chloramine-T Solution on the Characteristics of Light-Cured and Chemical-Cured Adhesives

This study evaluated the effect of a 0.5% chloramine T solution on a chemical-cured universal adhesive by comparing the light-cured, one-step, self-etch adhesive for the bonding performance, mechanical properties, and resin-dentin interfacial characteristics. Caries-free human molars were randomly assigned into eight groups based on the bonding systems employed (Bond Force II, BF and Bondmer Lightless, BL), the immersion solutions used before bonding (0.5% chloramine T solution and distilled water), and the immersion durations (5 and 60 min). Microtensile bond strength (μTBS), nanoleakage evaluation, and nanoindentation tests were performed, and the surface morphology of the resin-dentin interface was examined using a focus ion beam/scanning ion microscopy system. Immersion in chloramine-T for 5 min significantly decreased the μTBS of Bondmer Lightless (from 22.62 to 12.87 MPa) compared with that in distilled water. Moreover, there was also a decreasing trend after immersing in chloramine-T for 60 min (from 19.11 to 13.93 MPa). Chloramine T was found to have no effect on the hardness, elastic modulus, or morphological characteristics of the ion-beam milled resin-dentin interfacial surfaces in the tested adhesives, suggesting that chloramine T might reduce the bond strength by interfering with the interaction and the sealing between the adhesive resin and dentin in the chemical-cured universal adhesive, albeit without affecting the mechanical properties.

Effect of hot-etching treatment duration on the shear bond strength of zirconia-to-resin cement

The surface of zirconia was treated with hot-acid etching of different durations to improve its shear bond strength to resin. Zirconia discs were subjected to untreated, sand-blasting, and hot-etching treatments for 10, 30 and 60 min. The discs were bonded to the surface of bovine enamel specimens using RelyX Ultimate resin cement. The bonded specimens were divided into immediate and thermocyling aging groups according to whether they underwent thermal cycling. A universal mechanical testing machine was used to measure the shear bond strength of the specimens. One-way analysis of variance was used to determine the effect of hot-etching time on the shear bond strength. In the immediate and thermocyling aging groups, 60 min of hot-etching provided significantly higher shear bond strength than the other conditions (p<0.05).

Fracture resistance of monolithic translucent zirconia crown bonded with different self-adhesive resin cement: influence of MDP-containing zirconia primer after aging

OBJECTIVES

Successful ceramic restorations depend on the strong bonding with resin cement and even stress distribution. The aim of this study was to evaluate the impact of adding MDP-containing zirconia primer before self-adhesive resin cements with different functional acidic monomers on fracture resistance of monolithic zirconia crown.

MATERIALS AND METHODS

Eighty defect-free human maxillary premolars were divided according to the cement type and application of MDP-containing zirconia primer into eight groups (n = 10): Calibra Universal (C), Calibra Universal combined with zirconia primer (CZ), RelyX U200 (R), RelyXU200 combined with zirconia primer (RZ), Panavia SA Cement Plus (P), Panavia SA Cement Plus combined with zirconia primer (PZ), Multilink Speed (M), and Multilink Speed combined with zirconia primer (MZ). After teeth preparation and fabrication of zirconia crowns, each crown was bonded to its corresponding tooth. All specimens were subjected to 10,000 thermocycles between 5 and 55°C, followed by cyclic load (50 N) for 240,000 cycles. Each specimen was subjected to a static axial load until fracture using universal testing machine and the fracture load was recorded. The fracture mode studied and recorded. The fracture load results were analyzed using two-way ANOVA test (α = 0.05).

RESULTS

A significant interaction (P = 0.038) of combining MDP-containing zirconia primer and cement type on fracture resistance of monolithic zirconia crown was detected. The mean fracture load values of zirconia crown were significantly influenced by the combined application of the MDP-containing zirconia primer with Calibra Universal (P = 0.01), RelyX U200 (P < 0.001), and Multilink Speed (P = 0.038), while there was no significant difference with Panavia SA Cement Plus (P = 0.660). There was significant difference (F = 20.69, P < 0.001) between the mean fracture loads of groups with self-adhesive cements (C, R, P, and M groups). The highest fracture load was recorded with RZ group (2446.90 ± 126.72 N) while the lowest fracture load was recorded with C group (1623.18 ± 149.86 N).

CONCLUSIONS

The self-adhesive resin cement with different acidic functional monomer affects the fracture resistance of monolithic zirconia crown. Application of MDP-containing primer could improve the fracture resistance of monolithic zirconia crown with most self-adhesive cements. The application of an MDP-containing primer had no impact on the fracture resistance of monolithic translucent zirconia crown bonded by MDP-containing self-adhesive resin cement.

Bonding performance of universal adhesives to eroded dentine: A 6-year evaluation

OBJECTIVES

To evaluate the microtensile bond strength (µTBS) and nanoleakage (NL) of several universal adhesives to eroded dentine (ED) using etch-and-rinse (ER) and self-etch (SE) strategies, immediately and after 6 years of water storage.

MATERIAL AND METHODS

Four hundred and eighty human molars were distributed into 60 groups according to dentine substrate (sound dentine [SD], eroded with soft drink, or eroded with citric acid), application method of the adhesive (SE or ER), and the adhesives used: 1. All-Bond Universal, 2. Ambar Universal, 3. Clearfil Universal, 4. Futurabond U, 5. One Coat 7 Universal, 6. Peak Universal Bond, 7. Prime&Bond Elect, 8. Scotchbond Universal, 9. Tetric n-bond Universal, and 10. Xeno Select. The restoration was then performed with a composite resin, and the specimens were sectioned into resin-dentine bonded sticks. The sticks were tested (immediately or after 6 years of storage) for µTBS (0.5 mm/min) or used to assess NL. The eroded dentine surfaces were also examined using FE-SEM to evaluate the NL. Data for µTBS were analyzed by four-way ANOVA and Tukey's post-hoc test (a = 0.05), and the NL was analyzed by Kruskal-Wallis and the Wilcoxon Signed Rank Sum test (a = 0.05).

RESULTS

In ED, there was no difference in μTBS and NL between ER and SE strategies (p > 0.05). Most μTBS and NL values obtained for ED were lower and higher, respectively, than those for SD (p < 0.005). Additionally, the worst results (μTBS and NL) were observed for erosion with citric acid groups in comparison with erosion with soft-drink groups (p < 0.007). After 6y, μTBS was generally lower and NL higher for all substrates, adhesives, and strategies (p < 0.05), except for AMB, SBU, and TEU in dentine eroded with citric acid. The lowest μTBS and highest NL values were observed for ABU, FBU, OCU, PUB, PBE, and XEN in both types of eroded dentine and evaluation times (p < 0.002).

CONCLUSION

The use of MDP-containing adhesives seems to be essential to maintain adhesion to eroded dentine. However, other factors such as acidity should be considered.

CLINICAL SIGNIFICANCE

The bonding of eroded dentine is a challenge. However, the use of MDP-containing universal adhesives showed less degradation after long-term evaluation.

Machine Learning Analysis of Microtensile Bond Strength of Dental Adhesives

Dental adhesives provide retention to composite fillings in dental restorations. Microtensile bond strength (µTBS) test is the most used laboratory test to evaluate bonding performance of dental adhesives. The traditional approach for developing dental adhesives involves repetitive laboratory measurements, which consumes enormous time and resources. Machine learning (ML) is a promising tool for accelerating this process. This study aimed to develop ML models to predict the µTBS of dental adhesives using their chemical features and to identify important contributing factors for µTBS. Specifically, the chemical composition and µTBS information of 81 dental adhesives were collected from the manufacturers and the literature. The average µTBS value of each adhesive was labeled as either 0 (if <36 MPa) or 1 (if ≥36 MPa) to denote the low and high µTBS classes. The initial 9-feature data set comprised pH, HEMA, BisGMA, UDMA, MDP, PENTA, filler, fluoride, and organic solvent (OS) as input features. Nine ML algorithms, including logistic regression, k-nearest neighbor, support vector machine, decision trees and tree-based ensembles, and multilayer perceptron, were implemented for model development. Feature importance analysis identified MDP, pH, OS, and HEMA as the top 4 contributing features, which were used to construct a 4-feature data set. Grid search with stratified 10-fold cross-validation (CV) was employed for hyperparameter tunning and model performance evaluation using 2 metrics, the area under the receiver operating characteristic curve (AUC) and accuracy. The 4-feature data set generated slightly better performance than the 9-feature data set, with the highest AUC score of 0.90 and accuracy of 0.81 based on stratified CV. In conclusion, ML is an effective tool for predicting dental adhesives with low and high µTBS values and for identifying important chemical features contributing to the µTBS. The ML-based data-driven approach has great potential to accelerate the discovery of new dental adhesives and other dental materials.

Long-Term In Vitro Adhesive Properties of Two Universal Adhesives to Dentin

The composition of universal adhesives, as well as the adhesive strategy, may influence bonding effectiveness and durability. This study aimed to evaluate the microtensile bond strength (µTBS) and nanoleakage (NL), immediately and after 6-month aging, and in situ degree of conversion (DC), of two universal adhesives (Scotchbond Universal Adhesive, SBU; Xeno Select, XEN) applied with etch-and-rinse (ER) and self-etch (SE) strategies, in comparison with a two-step SE adhesive (Clearfil SE Bond, CSE). Dentin surfaces of fifty human third molars were randomly assigned to the following adhesives: two universal adhesives, SBU and XEN, applied in ER or SE mode and CSE, used as control. Teeth were sectioned into beams to be tested under µTBS, half of them after 24 h, and the rest after 6 months of water aging. Selected beams from each tooth were used for NL evaluation and in situ DC quantification. SBU and CSE showed significantly higher mean µTBS and lower nanoleakage than XEN, regardless of the evaluation time and adhesion strategy. XEN-SE yielded the lowest degree of conversion. Therefore, adhesive properties of universal adhesives to dentin are material dependent, regardless of the adhesion strategy, exhibiting XEN a significantly worse performance than SBU.

Progress in Dental Adhesive Materials

There have been significant advances in adhesive dentistry in recent decades, with efforts being made to improve the mechanical and bonding properties of resin-based dental adhesive materials. Various attempts have been made to achieve versatility, introducing functional monomers and silanes into the materials' composition to enable the chemical reaction with tooth structure and restorative materials and a multimode use. The novel adhesive materials also tend to be simpler in terms of clinical use, requiring reduced number of steps, making them less technique sensitive. However, these materials must also be reliable and have a long-lasting bond with different substrates. In order to fulfill these arduous tasks, different chemical constituents and different techniques are continuously being developed and introduced into dental adhesive materials. This critical review aims to discuss the concepts behind novel monomers, bioactive molecules, and alternative techniques recently implemented in adhesive dentistry. Incorporating monomers that are more resistant to hydrolytic degradation and functional monomers that enhance the micromechanical retention and improve chemical interactions between adhesive resin materials and various substrates improved the performance of adhesive materials. The current trend is to blend bioactive molecules into adhesive materials to enhance the mechanical properties and prevent endogenous enzymatic degradation of the dental substrate, thus ensuring the longevity of resin-dentin bonds. Moreover, alternative etching materials and techniques have been developed to address the drawbacks of phosphoric acid dentin etching. Altogether, we are witnessing a dynamic era in adhesive dentistry, with advancements aiming to bring us closer to simple and reliable bonding. However, simplification and novelty should not be achieved at the expense of material properties.

Effect of adhesive strategy on resin cement bonding to dentin

OBJECTIVE

The cement bonding strategy and the polymerization mode can influence the prognosis of indirect restorations. The microtensile bond strength (μTBS) and dentin endogenous enzymatic activity of a dual-cure resin cement (PV5) used in combination with two dentin surface conditioners (accelerator-enhancer primer, TP or universal adhesive, UA) were evaluated.

MATERIALS AND METHODS

PV5 was used to lute composite overlays after dentin treatment with TP or UA. The resin cement was self-cured, SC (1 h at 37 °C) or dual-cured, DC (20 s light-cure followed by 15 min self-cure at 37°C). The μTBS test, fractographic analysis, and the in situ zymography evaluations were performed after 24 h (T₀ ) or 1 yr (T₁₂ ) of artificial storage. Data were statistically analyzed (α = 0.05).

RESULTS

TP/DC obtained the highest adhesive strengths (45 ± 9 and 36.6 ± 8), while UA/SC (17 ± 8 and 11 ± 4) the lowest, both at T₀ and T₁₂ , respectively. DC resulted in superior bonding values than the SC, independent of the dentin surface treatment (p < 0.05). The type of adhesive, curing mode and aging influenced the gelatinolytic activity (p < 0.05).

CONCLUSIONS

The dual-cure resin cement used in combination with its accelerator-enhancer primer showed superior bonding performances with respect to universal adhesive. Dual-curing the resin cement was determinant to enhance bonding capability over time, independent of the adhesive strategy.

CLINICAL RELEVANCE

Clinicians must be aware to faithfully follow manufacturer's recommendation regarding the adhesive strategy suggested with the resin cement used.

Which self-etch acidic composition may result in higher dental bonds at the long-term? A network meta-analysis review of in vitro studies

OBJECTIVES

This review evaluated the effects of the acidic composition of self-etch (SE) adhesives at the long-term bond strengths to dentin and enamel.

DATA

The review followed the PRISMA Extension Statement for network meta-analysis. Studies were identified by a systematic search in PubMed, Web of Science, and Scopus databases.

STUDY SELECTION

The inclusion criteria were in vitro studies that evaluated bond strength data of samples analyzed at both immediate and long-term (after aging simulation) periods and that were bonded to sound dentin/enamel using SE adhesives, with at least one group of adhesives being based on 10-MDP (10-methacryloyloxy-decyl-dihydrogen-phosphate; control) and the other group being comprised of alternative acidic monomers. Statistical analyses were conducted using two methods: standard pairwise meta-analysis (SPMA) and Bayesian network meta-analysis (NMA). Heterogeneity was assessed by using the Cochran Q test and I² statistics.

RESULTS

From 5220 studies identified, 87 met the eligibility criteria and 83 were meta-analyzed. Seventeen adhesives were based on 10-MDP and 44 systems were based on alternative acids. The resin-dentin/enamel bonds were predominantly reduced after aging (∼84% of cases). From the SPMA findings, the following acidic compositions showed lower bond strength values (effect size: mean difference [MD] with 95% confidence interval [95% CI]) than 10-MDP: 4-META (MD -4.99, 95% CI: -7.21, -2.78; p<0.001); sulfonic acids (MD -9.59, 95% CI -12.19, -6.98; p<0.001); unspecified phosphate esters (MD -8.89, 95% CI -17.50, -0.28; p = 0.04); or mixed acids (MD -11.0, 95% CI -13.62, -8.38; p<0.001). The dental bonds were benefited from the presence of 10-MDP upon longer aging (>6 months). From the NMA probabilistic findings, adhesives based on 10-MDP and phosphonic acids ranked as having the best and the worst bonding potential to dentin, respectively. More than one composition (phosphonic acids and mixed acids) ranked similarly to 10-MDP in enamel. The studies scored as having moderate risk of bias (58.6%), followed by low (39.1%) and high (2.3%) risk of bias.

CONCLUSION

10-MDP is an outstanding acidic monomer that contributes to higher bonds to dentin at the long-term. In enamel, there is no evidence that one acidic composition prevails over the other.

CLINICAL SIGNIFICANCE

The acidic composition of SE adhesives affects the resistance of dental bonds after simulated aging, with 10-MDP playing a significant role in the adhesion to dentin but not to the enamel.

REGISTRATION NUMBER

This report is registered at the Open Science Framework (osf.io/urtdf).

Evaluation of the Bond Strength of Self-Etching Adhesive Systems Containing HEMA and 10-MDP Monomers: Bond Strength of Adhesives Containing HEMA and 10-MDP

The aim of this in vitro study was to assess the bond strength of self-etching adhesives containing HEMA and 10-MDP monomers. Twenty-four bovine teeth were divided into three groups. Two cylinders of composite resin were made in each tooth (n = 16): G1-Prime and Bond Universal (control); G2-OptiBond All-in-One (HEMA); and G3-Clearfil SE (10-MDP and HEMA). After 24-hour storage in distilled water, the specimens were fixed to a universal testing machine (Kratos Equipamentos Ltda.) for the microshear test at a speed of 0.5 mm/min. A qualitative analysis of the fracture pattern was also performed using scanning electron microscopy (500× magnification). The normality of sample data distribution was determined using the Shapiro–Wilk test. The results were assessed using the Kruskal–Wallis test, and α level of 5% was used for the analysis. The results indicated a statistical difference (p > 0.05) between G3 (15.6080 MPa) and G2 (11.2180 MPa). No statistical difference was observed when G1 (14,6325 MPa) was compared with the other two groups. It was also observed that a mixed fracture pattern was predominant in all groups. The self-etching adhesive containing HEMA and 10-MDP monomers showed to be promising in increasing the bond strength between the dental substrate and the composite resin, whereas the adhesive containing only HEMA exhibited lower bond strength to dentin.

The effect of different application modes of a 1-step self-etch adhesive on the clinical performance of Class I composite restorations: A randomized controlled clinical trial

OBJECTIVE

To evaluate the clinical performance of a 1-step self-etch dentin adhesive that was applied according to the manufacturers' recommendations, doubling the adhesive application time and layer in Class I cavities with a composite resin.

MATERIALS AND METHODS

A total of 39 patients aged between 14 and 43 (mean age: 19.1) years were enrolled in the study. Each patient received three restorations. In these three restorations, a 1-step self-etch adhesive was applied according to the manufacturer's recommendations (control group), by doubling the adhesive application time, and with double layers. The restorations were evaluated according to modified USPHS criteria at baseline, and 1, 2, 3, and 4-year recalls.

RESULTS

After 4 years, the success rate was 100% for restorations with the adhesive applied according to the manufacturers' recommendations, 96.9% for restorations applied by doubling the adhesive application time, and 93.8% for restorations applied with double adhesive layers. There was no significant difference between the three application methods among all the evaluation periods regarding the evaluation criteria.

CONCLUSIONS

The 4-year success rates of a 1-step self-etch dentin adhesive that was applied according to the manufacturers' recommendation, by doubling the adhesive application time, and with double layers were excellent.

CLINICAL SIGNIFICANCE

It is not recommended to double the adhesive application time nor apply a double layer of a 1-step self-etch adhesive because it does not improve the clinical performance of Class I composite restorations.

Role of 3-Methacryloxypropyltrimethoxysilane in Dentin Bonding

In this study, we aimed to examine the effect of 3-methacryloxypropyltrimethoxysilane (MPS) on dentin collagen and the impact of MPS and 10-methacryloyloxydecyl dihydrogen phosphate (MDP) together and separately on resin-dentin bonding. Eight groups of primers were prepared: control group, MDP, MPS5, MPS5 + MDP, MPS10, MPS10 + MDP, MPS15, and MPS15 + MDP. The potential interaction between MPS and collagen was assessed by molecular dynamics, contact angle measurement, zeta potential measurement, and chemoanalytic characterization using X-ray photoelectron spectroscopy, Raman spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and ultraviolet-visible spectroscopy. Microtensile bond strength (μTBS) and nanoleakage were evaluated after 24 h or 12 months of water storage. In situ zymography was used to evaluate the enzyme activity at the bonded interface. According to chemoanalytic characterization and molecular dynamics, a weak interaction between MPS and collagen was observed. MPS enhanced the hydrophobicity and negative charge of the collagen surface (P < 0.05). Applying an MDP-containing primer increased μTBS (P > 0.05) and reduced fluorescence after 24 h of water storage. Water storage for 12 months decreased μTBS (P < 0.05) and increased nanoleakage for all groups. MPS conditioning did not change μTBS and nanoleakage after 24 h of water storage or aging. The MPS10 + MDP and MPS15 + MDP groups presented more silver nitrate and μTBS decrease than the MDP group (P < 0.05). These results indicated that MPS had a weak interaction with collagen that enhanced its surface negative charge and hydrophobicity without adversely affecting dentin bonding. However, compared to MDP alone, mixing MDP with MPS impaired their effectiveness and made the dentin bonding unstable.

Interactions of two phosphate ester monomers with hydroxyapatite and collagen fibers and their contributions to dentine bond performance

OBJECTIVES

To evaluate the interactions of two phosphate ester monomers [10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) and dipentaerythritol penta-acrylate phosphate (PENTA)] with hydroxyapatite and collagen and understand their influence on dentine bonding.

METHODS

Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, nuclear magnetic resonance, ultraviolet-visible, and molecular docking were applied for separately evaluating the interactions of two monomers with hydroxyapatite and collagen. Hydrophilicity tests and morphological observation were employed to characterize pretreated dentine. Microtensile bond strength (μTBS) and nanoleakage were investigated to evaluate the bonding performance. Hydroxyproline assay, in situ zymography, and matrix metalloproteinase-9 (MMP-9) activity assay were used to confirm the MMP inhibition.

RESULTS

Chemoanalytic characterization confirmed the interactions of 10-MDP and PENTA with hydroxyapatite and collagen. The interactions of PENTA were weaker than 10-MDP. PENTA possessed better dentine tubule sealing after etching than 10-MDP. Dentine treated with PENTA was more hydrophilic than 10-MDP. 10-MDP and PENTA treating significantly increased the initial μTBS than the control group without primer conditioning. μTBS decreased significantly during aging, and the decrease was more severe in the PENTA group than 10-MDP. The 10-MDP and PENTA groups exhibited relatively less fluorescence than the control. The relative inhibition percentages of MMP-9 decreased in the order of 10-MDP-Ca salt, 10-MDP and PENTA. The 10-MDP, PENTA, and 10-MDP-Ca salt groups showed significantly lower hydroxyproline contents than the control.

CONCLUSIONS

Although PENTA adsorbed on hydroxyapatite, it did not form a stable calcium salt. The interactions of 10-MDP with hydroxyapatite and collagen are different than those of PENTA.

CLINICAL SIGNIFICANCE

The sealing of dentinal tubules by PENTA and the inhibition of MMP by 10-MDP and its calcium salts contribute to improving the dentine bonding durability.