ZIF-67 Derived Nanostructures of Co/CoO and Co@N-doped Graphitic Carbon as Counter Electrode for Highly Efficient Dye-sensitized Solar Cells

Nickel foam-loaded Co-MOF@TiO2/MoS2 as electrode materials for dual-function devices for glucose detection and hydrogen evolution

Dual-functional nanomaterial electrodes have the capability to satisfy the requirements for both sweat analysis and the hydrogen evolution reaction (HER), thereby enabling the integration of electrochemical sensing and hydrogen production. In this study, ZIF-67 cubes are synthesized on nickel foam (NF), while TiO2 is obtained through an annealing process. Subsequently, the ZIF-67@TiO2/MoS2 nanocomposite is fabricated on nickel foam via a hydrothermal method. This composite material exhibits exceptional photocatalytic properties and is also suitable for the detection of glucose in sweat. The glucose detection range spans from 10 nM to 10 mM with a sensitivity of 7.24 μA mM-1 cm-2 for a signal-to-noise ratio of 3 and a detection limit of 0.43 μM. Moreover, when utilized as a hydrogen evolution electrode, this material demonstrates a current density of 10 mA cm-2 at an overpotential of 118 mV, with a Tafel slope of 73 mV/dec. The synthesis process is both straightforward and economical. This research introduces a novel concept for the design of multifunctional chemical sensors.

Highly efficient activation of peroxymonosulfate by ZIF-67 anchored cotton derived for ciprofloxacin degradation

Metal-organic framework (MOF) and MOF-derived materials have attracted extensive research interest as environmental catalysts. In this study, a composite material (ZIF-67/CCot-8) was successfully prepared using cotton fiber as a substrate and growing ZIF-67 in situ. This material exhibited excellent catalytic performance and significantly improved the efficiency of antibiotics degradation. ZIF-67/CCot-8 at a concentration of 0.05 g/L, combined with 0.2 mM peroxymonosulfate (PMS), removed approximately 97% of ciprofloxacin (CIP) and 99% of tetracycline and sulfamethoxazole within 15 min. The high catalytic efficiency of this catalyst is mainly attributed to the uniform distribution of ZIF-67-derived nanoparticles on the surface of the cotton fibers, providing abundant active sites and thereby significantly enhancing the efficiency of antibiotics degradation. Radical quenching experiments and electron paramagnetic resonance (EPR) analyses revealed that sulfate radicals (SO4•-) and singlet oxygen (1O2) were the main active species. Mass spectrometry (MS) was used to elucidate the CIP degradation pathway. The growth of the roots and stems of soybean sprouts in different water environments (tap water, treated water, and untreated water) was also observed. The results demonstrated a significant improvement in the inhibition of plant growth in the post-degradation CIP solution, indicating a substantial reduction in the toxicity of the degraded aqueous solution. To validate the practicality of the ZIF-67/CCot-8/PMS system, a continuous-flow water-treatment device was designed. This system removed 98% of the CIP solution within 180 min, demonstrating its excellent durability. This study presents a potential pathway for effective antibiotics removal using MOF-derived materials.

Eco-friendly fabrication of nonenzymatic electrochemical sensor based on cobalt/polymelamine/nitrogen-doped graphitic-porous carbon nanohybrid material for glucose monitoring in human blood

The design and development of eco-friendly fabrication of cost-effective electrochemical nonenzymatic biosensors with enhanced sensitivity and selectivity are one of the emerging area in nanomaterial and analytical chemistry. In this aspect, we developed a facile fabrication of tertiary nanocomposite material based on cobalt and polymelamine/nitrogen-doped graphitic porous carbon nanohybrid composite (Co-PM-NDGPC/SPE) for the application as a nonenzymatic electrochemical sensor to quantify glucose in human blood samples. Co-PM-NDGPC/SPE nanocomposite electrode fabrication was achieved using a single-step electrodeposition method under cyclic voltammetry (CV) technique under 1 M NH₄Cl solution at 20 constitutive CV cycles (sweep rate 20 mV/s). Notably, the fabricated nonenzymatic electroactive nanocomposite material exhibited excellent electrocatalytic sensing towards the quantification of glucose in 0.1 M NaOH over a wide concentration range from 0.03 to 1.071 mM with a sensitive limit of detection 7.8 μM. Moreover, the Co-PM-NDGPC nanocomposite electrode with low charge transfer resistance (Rct∼81 Ω) and high ionic diffusion indicates excellent stability, reproducibility, and high sensitivity. The fabricated nanocomposite materials exhibit a commendable sensing response toward glucose molecules present in the blood serum samples recommends its usage in real-time applications.

Core-shell Au@ZIF-67-based pollutant monitoring of thiram and carbendazim pesticides

A sensitive and stable substrate plays a vital role in the Raman spectroscopic techniques as an analytical method for detecting pesticides effectively from the environment. Enhancing signals from nanoparticles are weak and inconsistent in repeatability since analytes tend to degrade quickly under laser exposure. Herein, a novel substrate of Au@ZIF-67 is prepared on octahedral AuNPs by trapping pesticide molecules with small three-dimensional volumes by the flexibility of ZIF-67 for rapid detection with high sensitivity and stability. The two types of thiram and carbendazim pesticides, which are environmental pollutants that affect biodiversity, were successfully absorbed in Au@ZIF-67 nanostructures by adsorption-desorption equilibrium for analytical purposes in Raman spectroscopy. Spectra calculations of the thiram and carbendazim molecules on 8 atoms of Au using DFT were compared with the experimental data. The SERS enhancement factors for thiram and carbendazim were estimated to be 1.91 × 10⁸ and 3.12 × 10⁸, respectively, with the LOD values of trace amounts of ∼10^-10 mol L^-1. The novel substrate of Au@ZIF-67 is a propitious platform for detecting thiram and carbendazim in trace amounts, providing a helpful strategy for detecting residues with high performance in the environment at the laboratory and practical scales.

Engineering Sulfur Vacancies in Spinel-Phase Co3S4 for Effective Electrocatalysis of the Oxygen Evolution Reaction

Restricted by the sluggish kinetics of the oxygen evolution reaction (OER), efficient OER catalysis remains a challenge. Here, a facile strategy was proposed to prepare a hollow dodecahedron constructed by vacancy-rich spinel Co₃S₄ nanoparticles in a self-generated H₂S atmosphere of thiourea. The morphology, composition, and electronic structure, especially the sulfur vacancy, of the cobalt sulfides can be regulated by the dose of thiourea. Benefitting from the H₂S atmosphere, the anion exchange process and vacancy introduction can be accomplished simultaneously. The resulting catalyst exhibits excellent catalytic activity for the OER with a low overpotential of 270 mV to reach a current density of 10 mA cm^-2 and a small Tafel slope of 59 mV dec^-1. Combined with various characterizations and electrochemical tests, the as-proposed defect engineering method could delocalize cobalt neighboring electrons and expose more Co²⁺ sites in spinel Co₃S₄, which lowers the charge transfer resistance and facilitates the formation of Co³⁺ active sites during the preactivation process. This work paves a new way for the rational design of vacancy-enriched transition metal-based catalysts toward an efficient OER.

Metal-organic Framework ZIF-67 Functionalized MXene for Enhancing the Fire Safety of Thermoplastic Polyurethanes

In this work, a novel functionalization strategy for ZIF-67-modified layered MXene was proposed, aiming at improving the fire safety of thermoplastic polyurethanes (TPU). The ZIF-67@MXene was verified by microscopic morphology, elemental composition, functional group species and crystal structure, and then the successfully prepared ZIF-67@MXene was introduced into the TPU material. When ZIF-67@MXene content was only 0.5 wt%, the peak heat release rate, total heat release rate, peak smoke release rate, total smoke release rate, and CO yield of the TPU/ZIF-67@MXene composites were reduced by 26%, 9%, 50%, and 22%, respectively, compared with the pure TPU. The thermogravimetric tests showed that the residual char of TPU/ZIF-67@MXene composites was the most in all samples. In short, the high-quality carbon layer of TPU/ZIF-67@MXene composites acts as a physical barrier to the transfer of heat and toxic gases, greatly improving the flame retardant properties of the TPU polymer.

Environmental decomposition and remodeled phytotoxicity of framework-based nanomaterials

Zeolitic imidazole frameworks (ZIFs) have attracted a considerable amount of attention for use in environmental applications (e.g., pollutant adsorption and photocatalysis in water treatments). The environmental stability and toxicity of ZIFs are key prerequisites for their practical applications, but information about these factors is largely lacking. The present work finds that pristine ZIFs (ZIF-8 and ZIF-67) photodegrade from frame structures into two-dimensional nanosheets and are oxidized to zinc carbonate (ZIF-8) and Co₃O₄ (ZIF-67) under visible-light irradiation. The photoinduced electrons, holes and free radicals promote dissolution of the metal cores and organic ligands, leading to collapse of the frame structure. The photodegradation of ZIF-8 alleviates developmental inhibition, oxidative stress, plasmolysis, and photosynthetic toxicity, while the photodegradation of ZIF-67 aggravates nanotoxicity. The integration of metabolomics and transcriptomics analysis reveals that unsaturated fatty acid biosynthesis and metal ion-binding transcription contribute to the altered toxicity of ZIF photodegradation. These findings highlight the roles of photodegradation in structural transformation and alteration of the toxicity of ZIFs, alarming the study of pristine metal-organic frameworks (MOFs).

Laser In-Situ synthesis of metallic cobalt decorated porous graphene for flexible In-Plane microsupercapacitors

Transition metal nanoparticles-graphene nanocomposites incorporate the advantages of graphene and metal nanoparticles, which arouse extensive attention. Here, we design a novel, facile and versatile method for in-situ synthesis of laser-induced porous graphene (LIG) decorated with cobalt particles (Co). The LIG/Co nanocomposites are fabricated through one-step laser direct scribing on a customized film composed of polyimide (PI) powder, polyvinyl alcohol (PVA), and cobalt chloride (CoCl₂·6H₂O) precursors. Benefiting from the unique properties of Co nanoparticles embedded LIG, the obtained optimal in-plane micro-supercapacitors (IMSC) based on LIG/Co-1.5 possesses an excellent areal capacitance of 110.11 mF cm^-2 and a superior energy density of 9.79 μWh cm^-2, which are about 79 times that of pure LIG-based IMSCs. Simultaneously, the LIG/Co-1.5 MSCs also present good cycling stability, remarkable modular integration capability, and outstanding mechanical flexibility, showing potential for practical applications. Additionally, the density functional theory (DFT) calculations indicate that the decorating of cobalt particles elevates electron transfer. Moreover, the interaction between electrolyte and electrodes is also improved with the introduction of cobalt particles. Therefore, this strategy offers a new avenue for facile and large-scale manufacturing of various metallic atoms in-situ decorating in porous graphene.

Investigation of MOF-derived humidity-proof hierarchical porous carbon frameworks as highly-selective toluene absorbents and sensing materials

Carbon frameworks (CFs) derived from metal-organic frameworks (MOFs) have been produced as adsorbents of toluene. To further obtain optimum hierarchical porous carbon structure of CFs, different treatment temperatures were applied to a typical kind of MOFs (ZIF-8). The adsorption capacity of the toluene of hierarchical porous CFs obtained from ZIF-8 under 1100 °C (CF-1100, adsorption capacity of 208.5 mg/g) was higher than that of other carbonization temperature and MOFs. Impressively, the adsorbent CF-1100 also exhibited strong hydrophobicity, low desorption temperature, and good selectivity to toluene. The adsorption capacity decreased by only 10.4% under wet condition compared with the dry condition, standing on the top of the recently reported adsorbents. The impressive adsorption performance of CF-1100 is attributed to the larger specific surface area (1024 m²/g) and pore volume (0.497 cm³/g), newly generated micropores (pore width is 0.6-0.8 nm) and mesopores (pore width above 10 nm), and carbonaceous structure with higher degree of graphitization. Based on the adequate adsorption performance, CF-1100 coated quartz crystal microbalances as sensor also showed a high sensitivity of 0.4004 Hz/ppm and small relative standard deviations of 1.0745% for toluene sensing. This contribution provides a foundation for optimizing potential adsorbents and sensing materials for air pollution abatement.

Consecutive Nucleation and Confinement Modulation towards Li Plating in Seeded Capsules for Durable Li-Metal Batteries

A dual modulation strategy of consecutive nucleation and confined growth of Li metal is proposed by using the metal-organic framework (MOF) derivative hollow capsule with inbuilt lithiophilic Au or Co-O nanoparticle (NP) seeds as heterogeneous host. The seeding-induced nucleation enables the negligible overpotential and promotes the inward injection of Li mass into the abundant cavities in host, followed by the conformal plating of Li on the outer surface of host during discharging. This modulation alleviates the dendrite growth and volume expansion of Li plating. The interconnected porous host network enables enhancement of cycling and rate performances of Li metal (a lifespan over 1200 h for Au-seeding symmetric cells, and an endurance of 220 cycles under an ultrahigh current density of 10 mA cm^-2 for corresponding asymmetric cells). The hollow capsules integrated with lithiophilic seeds solve the deformation problem of Li metal for durable and long-life Li-metal batteries.

Versatile design of metal-organic framework cathode for Li-O2 and Li-O2/CO2 batteries

In this study, we propose a versatile design for metal-organic framework cathodes with the aim of improving the reversibility of Li-O₂ and Li-O₂/CO₂ batteries. The porous nanoarchitecture of Co₃O₄-incorporated carbon wrapped with carbon nanotubes is beneficial for facilitating the reversible electrochemical reactions with O₂ and CO₂, ensuring long-term cycling performance.

Rational Design of Hierarchical Structural CoSe@NPC/CoSe@CNT Nanocomposites Derived from Metal-Organic Frameworks as a Robust Pt-free Electrocatalyst for Dye-Sensitized Solar Cells

Transition-metal compounds/carbon hybrids with high electrocatalytic capability possess attractive potential as a counter electrode (CE) for dye-sensitized solar cells (DSSCs). However, the simple structure and agglomeration always result in poor performance. Herein, cobalt selenides confined in hollow N-doped porous carbon interconnected by carbon nanotubes (CNTs) with cobalt selenides encapsulated inside (denoted as CoSe@NPC/CoSe@CNTs) are formed through in situ pyrolysis and selenization process. In this strategy, ZIF-67 is used as the precursor, structure inducer, and carbon source for the orientated growth of CNTs. Such a rational architecture provides a stable interconnected conductive network and a hierarchically porous structure, with more available active sites and a shortened pathway for charge transport, synergistically enhancing the electrocatalytic activity. Specifically, the DSSCs based on CoSe@NPC/CoSe@CNTs demonstrate a high efficiency of 7.36%, even superior to that of Pt (7.16%). Furthermore, the CoSe@NPC/CoSe@CNT CE also demonstrates a good long-term stability in the iodine-based electrolyte.

Recent progress on nanostructured carbon-based counter/back electrodes for high-performance dye-sensitized and perovskite solar cells

Dye-sensitized solar cells (DSSCs) and perovskite solar cells (PSCs) favor minimal environmental impact and low processing costs, factors that have prompted intensive research and development. In both cases, rare, expensive, and less stable metals (Pt and Au) are used as counter/back electrodes; this design increases the overall fabrication cost of commercial DSSC and PSC devices. Therefore, significant attempts have been made to identify possible substitutes. Carbon-based materials seem to be a favorable candidate for DSSCs and PSCs due to their excellent catalytic ability, easy scalability, low cost, and long-term stability. However, different carbon materials, including carbon black, graphene, and carbon nanotubes, among others, have distinct properties, which have a significant role in device efficiency. Herein, we summarize the recent advancement of carbon-based materials and review their synthetic approaches, structure-function relationship, surface modification, heteroatoms/metal/metal oxide incorporation, fabrication process of counter/back electrodes, and their effects on photovoltaic efficiency, based on previous studies. Finally, we highlight the advantages, disadvantages, and design criteria of carbon materials and fabrication challenges that inspire researchers to find low cost, efficient and stable counter/back electrodes for DSSCs and PSCs.

Engineering magnetic N-doped porous carbon with super-high ciprofloxacin adsorption capacity and wide pH adaptability

We report a high performance magnetic N-doped nanoporous carbon (MNPC) adsorbent synthesized by a simple single-step pyrolysis protocol. Grinding the mixture of ZnO nanoparticles, cobalt hydroxide and 2-methylimidazole produced Zn/Co-ZIFs that were converted into MNPC following subsequent pyrolysis in N₂ atmosphere. The optimized MNPC-700-0.4 adsorbent, obtained at 700 °C with Co/(Zn + Co) molar ratio of 0.4, is featured with super-high ciprofloxacin (CIP) adsorption capacity of 1563.7 mg g^-1 at 25 °C, fast adsorption dynamics (1.5 h of adsorption equilibrium time), wide pH adaptability (almost unchanged CIP adsorption capacity in pH 4-10), and good magnetic property. The magnetic property and CIP adsorption performance can be easily regulated by modulating the molar ratio of Co/(Zn + Co) and the pyrolysis temperature. The optimal MNPC-700-0.4 was chosen to explore adsorption kinetics and isotherm. The effects of pH, ionic strength and humic acid on CIP adsorption were investigated. CIP adsorption obeyed pseudo-second-order kinetics and well fitted the Langmuir adsorption model. The favorable textural properties (high surface area and pore volume), riched nitrogen structure and large amounts of defects endow the MNPC-700-0.4 lots of sites for CIP adsorption. The CIP adsorption onto MNPC-700-0.4 was mainly controlled by the electrostatic interaction, hydrophobic interaction, π-π stacking and hydrogen bond.

Facile synthesis of magnetic carbon nanotubes derived from ZIF-67 and application to magnetic solid-phase extraction of profens from human serum

Magnetic carbon nanotubes (CNTs) with encapsulated Co nanoparticles (Co@CNTs), was synthesized by exploiting the one-step pyrolysis strategy using ZIF-67 as template. The as-synthesized Co@CNTs is provided with the nanopores, a large specific surface area, and strong magnetic response. The obtained Co@CNTs was used as magnetic solid-phase extraction adsorbents to extract two profens including flurbiprofen and ketoprofen. The parameters of extraction efficiency, involving extraction time, sample solution volume, ionic strength, pH and the conditions of desorption efficiency, were optimized in detail. After determined by high-performance liquid chromatography-ultraviolet (HPLC-UV), the results evinced that Co@CNTs showed a high extraction efficiency with high enrichment factors of 832 and 672. The good linear range of both flurbiprofen and ketoprofen were all 5.0-1000 ng L^-1, with the limit of detection were 0.60 ng L^-1 and 0.70 ng L^-1, respectively. Furthermore, a valid method for the extraction of flurbiprofen and ketoprofen from human serum was established. The spiking recoveries of two profens were between 86.74% and 97.22%, and the relative standard deviation was less than 6.55%. Co@CNTs can be repeatedly used at least 10 times, indicating its excellent regeneration and reusability. The results demonstrated that the Co@CNTs materials exhibits high enrichment ability and extraction efficiency, playing great promise in MSPE.

Ambient Temperature NO Adsorber Derived from Pyrolysis of Co-MOF(ZIF-67)

Co-, Ni-, and Zn-containing MOFs are prepared and then pyrolyzed to generate materials for ambient temperature NO adsorption. Materials containing Co are much more efficient for NO adsorption than those containing Ni and Zn; therefore, Co is identified as the active phase. The best performing material studied here achieves 100% low concentration (10 ppm) NO adsorption for more than 15 h under a weight hourly space velocity of 120 000 mL g^-1 h^-1. Powder X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared, and Raman spectroscopies, along with scanning electron microscopy and TEM, are used to probe the physicochemical properties of the materials, particularly the Co active phase, and chemistries involved in NO adsorption-desorption. NO adsorbs on oxygen-covered Co nanoparticle surfaces in the form of nitrates and desorbs as NO at higher temperatures as a result of surface nitrate decomposition. NO storage capacity decreases gradually upon repeated NO adsorption-desorption cycles, likely because of Co₃O₄ formation during these processes.

Nitrogen-doped graphitic hierarchically porous carbon nanofibers obtained via bimetallic-coordination organic framework modification and their application in supercapacitors

Herein, N-doped graphitic hierarchically porous carbon nanofibers (NGHPCF) were prepared by electrospinning the composite of bimetallic-coordination metal-organic frameworks and polyacrylonitrile, followed by a pyrolysis and acid wash process. Control over the N content, specific surface area, and degree of graphitization of NGHPCF materials has been realized by adjusting the Co/Zn metal coordination content as well as the pyrolysis temperature. The obtained NGHPCF with a high specific surface area (623 m2 g-1) and nitrogen content (13.83 wt%) exhibit a high capacitance of 326 F g-1 at 0.5 A g-1. In addition, the capacitance of 170 F g-1 is still maintained at a high current density (40 A g-1); this indicates a high capacitance retention capability. Furthermore, a superb energy density (9.61 W h kg-1) is obtained with a high power density (62.4 W kg-1) using an organic electrolyte. These results fully illustrate that the prepared NGHPCF binder-free electrodes are promising candidates for high-performance supercapacitors.

The development of MOFs-based nanomaterials in heterogeneous organocatalysis

Metal-organic framework (MOF) is a class of inorganic-organic hybrid material assembled periodically with metal ions and organic ligands. MOFs have always been the focuses in a variety of frontier fields owing to the advantageous properties, such as large BET surface areas, tunable porosity and easy-functionalized surface structure. Among the various application areas, catalysis is one of the earliest application fields of MOFs-based materials and is one of the fastest-growing topics. In this review, the main roles of MOFs in heterogeneous organocatalysis have been systematically summarized, including used as support materials (or hosts), independent catalysts, and sacrificial templates. Moreover, the application prospects of MOFs in photocatalysis and electrocatalysis frontiers were also mentioned. Finally, the key issues that should be conquered in future were briefly sketched in the final parts of each item. We hope our perspectives could be beneficial for the readers to better understand these topics and issues, and could also provide a direction for the future exploration of some novel types of MOFs-based nanocatalysts with stable structures and functions for heterogeneous catalysis.

Synthesis of nanoporous cobalt/carbon materials by a carbonized zeolitic imidazolate framework-9 and adsorption of dyes

The cobalt/carbon material Z9-600 exhibits a high adsorption capacity for methylene green and a high regeneration efficiency after 4 cycles of use and reuse.

Multiple active components, synergistically driven cobalt and nitrogen Co-doped porous carbon as high-performance oxygen reduction electrocatalyst

Economical g-C₃N₄derived Co,N dual-doped porous carbon with multiple active components shows high-performance oxygen reduction electrocatalytic activity.