Sandwich nanoporous framework decorated with vertical CuO nanowire arrays for electrochemical glucose sensing

An efficient biosensor using a functionalized microneedle of Cu2O-based CoCu-LDH for glucose detection

Glucose detection with small and micro volume sampling has recently received increasing attention in monitoring personal health. Herein, a cauliflower-type cluster of Cu2O nanoparticles (NPs) was directly deposited on the tip surface of a stainless steel acupuncture needle electrode (ANE) by electrochemical deposition, and then this pre-formed cuprous basis was used to further prepare the neatly arranged CoCu-layered double hydroxide (CoCu-LDH) nanosheets that interconnected to form nano-sized pores in the range from 100 to 500 nm. The microstructure and spectral characteristics of the surface modification materials were comprehensively characterized by FE-SEM, EDS, XRD, FT-IR and TEM. Cu2O-based CoCu-LDH composites with special morphology had been proven to accelerate the rate of electron transport and provide more available active centers, and moreover, the mixed valence of Cu/Co induced an excellent synergism for the electrocatalytic oxidation of glucose. As a result, CoCu-LDH/Cu2O/ANE as a sensitive glucose probe exhibited two wider linear ranges of 0.03-0.40 mM and 0.40-6.00 mM, with sensitivities of 116.13 μA mM-1 and 52.08 μA mM-1, respectively, and the detection limit as low as 0.46 μM (S/N = 3). The response time only took 3 s and it kept working stably in the interference of ascorbic acid (AA), dopamine (DA), uric acid (UA), and Cl-. In the stability test, the CoCu-LDH/Cu2O/ANE sensor exhibited a stable monitoring sensitivity after 15 days. Finally, the CoCu-LDH/Cu2O/ANE sensor had been successfully applied to glucose analysis in human serum, proving that our design was an attractive strategy for developing a portable, minimally invasive, and low-cost non-enzymatic electrochemical glucose sensing platform.

Electrochemical Determination of 17-β-Estradiol Using a Glassy Carbon Electrode Modified with α-Fe2O3 Nanoparticles Supported on Carbon Nanotubes

In this study, a novel electrochemical assay for determining 17-β-estradiol (E2) was proposed. The approach involves modifying a glassy carbon electrode (GCE) with a nanocomposite consisting of α-Fe2O3 nanoparticles supported on carbon nanotubes (CNTs)-denoted as α-Fe2O3-CNT/GCE. The synthesis of the α-Fe2O3-CNT nanocomposite was achieved through a simple and cost-effective hydrothermal process. Morphological and chemical characterization were conducted using scanning electron microscopy (SEM), Raman spectroscopy, and energy-dispersive X-ray spectroscopy (EDX). The presence of the α-Fe2O3-CNT film on the GCE surface resulted in an enhanced electrochemical response to E2, preventing electrode surface fouling and mitigating the decrease in peak current intensity during E2 oxidation. These outcomes substantiate the rationale behind the GCE modification. After the optimization of experimental conditions, E2 was determined by the square wave voltammetry technique using 0.1 mol L-1 KCl solution (pH = 7.0) with 20% ethanol as a supporting electrolyte. A linear concentration range of 5.0-100.0 nmol L-1 and a low limit of detection of 4.4 nmol L-1 were obtained. The electroanalytical method using α-Fe2O3-CNT/GCE was applied for E2 determination in pharmaceutical, lake water, and synthetic urine samples. The obtained results were attested by recovery tests and by high-performance liquid chromatography as a comparative technique at a 95% confidence level. Thus, the developed electrochemical sensor is simple and fast to obtain, presents high accuracy, and is viable for determining E2 in routine analysis.

Focus Review on Nanomaterial-Based Electrochemical Sensing of Glucose for Health Applications

Diabetes management can be considered the first paradigm of modern personalized medicine. An overview of the most relevant advancements in glucose sensing achieved in the last 5 years is presented. In particular, devices exploiting both consolidated and innovative electrochemical sensing strategies, based on nanomaterials, have been described, taking into account their performances, advantages and limitations, when applied for the glucose analysis in blood and serum samples, urine, as well as in less conventional biological fluids. The routine measurement is still largely based on the finger-pricking method, which is usually considered unpleasant. In alternative, glucose continuous monitoring relies on electrochemical sensing in the interstitial fluid, using implanted electrodes. Due to the invasive nature of such devices, further investigations have been carried out in order to develop less invasive sensors that can operate in sweat, tears or wound exudates. Thanks to their unique features, nanomaterials have been successfully applied for the development of both enzymatic and non-enzymatic glucose sensors, which are compliant with the specific needs of the most advanced applications, such as flexible and deformable systems capable of conforming to skin or eyes, in order to produce reliable medical devices operating at the point of care.

Non-enzymatic glucose sensors composed of trimetallic CuO/Ag/NiO based composite materials

The escalating risk of diabetes and its consequential impact on cardiac, vascular, ocular, renal, and neural systems globally have compelled researchers to devise cost-effective, ultrasensitive, and reliable electrochemical glucose sensors for the early diagnosis of diabetes. Herein, we utilized advanced composite materials based on nanoporous CuO, CuO/Ag, and CuO/Ag/NiO for glucose detection. The crystalline structure and surface morphology of the synthesized materials were ascertained via powder X-ray diffraction (P-XRD), energy dispersive X-ray (EDX) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. The electro-catalytic properties of the manufactured electrode materials for glucose electro-oxidation in alkaline conditions were probed using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. Notably, the CuO/Ag/NiO electrode material exhibited exceptional performance as a non-enzymatic glucose sensor, displaying a linear range of 0.001-5.50 mM, an ultrahigh sensitivity of 2895.3 μA mM^-1 cm^-2, and a low detection limit of 0.1 μM. These results suggest that nanoporous CuO/Ag/NiO-based composite materials are a promising candidate for early diagnosis of hyperglycemia and treatment of diabetes. Furthermore, non-enzymatic glucose sensors may pave the way for novel glucometer markets.

Hydrazine High-Performance Oxidation and Sensing Using a Copper Oxide Nanosheet Electrocatalyst Prepared via a Foam-Surfactant Dual Template

This work demonstrates hydrazine electro-oxidation and sensing using an ultrathin copper oxide nanosheet (CuO-NS) architecture prepared via a versatile foam-surfactant dual template (FSDT) approach. CuO-NS was synthesised by chemical deposition of the hexagonal surfactant Brij^®58 liquid crystal template containing dissolved copper ions using hydrogen foam that was concurrently generated by a sodium borohydride reducing agent. The physical characterisations of the CuO-NS showed the formation of a two-dimensional (2D) ultrathin nanosheet architecture of crystalline CuO with a specific surface area of ~39 m²/g. The electrochemical CuO-NS oxidation and sensing performance for hydrazine oxidation revealed that the CuO nanosheets had a superior oxidation performance compared with bare-CuO, and the reported state-of-the-art catalysts had a high hydrazine sensitivity of 1.47 mA/cm² mM, a low detection limit of 15 μM (S/N = 3), and a linear concentration range of up to 45 mM. Moreover, CuO-NS shows considerable potential for the practical use of hydrazine detection in tap and bottled water samples with a good recovery achieved. Furthermore, the foam-surfactant dual template (FSDT) one-pot synthesis approach could be used to produce a wide range of nanomaterials with various compositions and nanoarchitectures at ambient conditions for boosting the electrochemical catalytic reactions.

Hierarchical Structures Composed of Cu(OH)2 Nanograss within Directional Microporous Cu for Glucose Sensing

Cu(OH)₂ nanomaterials are widely investigated for non-enzymatic glucose sensors due to their low-cost and excellent performance. Cu(OH)₂ nanomaterials usually grow on substrates to form sensor electrodes. Reported works mainly focus on structure adjusting of the Cu(OH)₂ nanostructures, while the optimization of substrates is still lacking. In the present work, directional porous Cu (DPC) was applied as the substrate for the growth of Cu(OH)₂ nanograss (NG), and hierarchical structures of Cu(OH)₂@DPC were prepared by alkaline oxidation. The morphology and microstructure evolution of the prepared hierarchical structures was investigated, and the non-enzymatic glucose sensing performance was evaluated. Cu(OH)₂@DPC exhibits enhanced comprehensive non-enzymatic glucose sensing performance compared to the reported ones, which may benefit from both the effective adsorption of the Cu(OH)₂ NG with a relatively high surface area and the high solute exchange of the DPC by a channel effect. This work provides new insights into the further improvement of the non-enzymatic glucose sensing performance of Cu(OH)₂ nanostructures by optimizing the substrate structure.

Tellurium in carbohydrate synthesis

In this article, we discuss about the influence of tellurium in carbohydrate synthesis. Mainly the chapter focuses on the importance of the tellurium during the synthesis of glycosides and during the oxidation of glucose.

Glucose determination using amperometric non-enzymatic sensor based on electroactive poly(caffeic acid)@MWCNT decorated with CuO nanoparticles

A novel non-enzymatic glucose sensor based on poly(caffeic acid)@multi-walled carbon nanotubes decorated with CuO nanoparticles (PCA@MWCNT-CuO) was developed. The described approach involves the complexation/accumulation of Cu(II) on PCA@MWCNT followed by electrochemical CuO deposition in an alkaline electrolyte. The morphology and surface characteristics of the nanomaterial were determined by transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), atomic force microscopy (AFM), Raman spectroscopy, and inductively coupled plasma mass spectrometry (ICP-MS). A hybrid-support sensor device was then developed to assess the glucose concentration in different solutions. The sensitivity of the electrode is 2412 μA mM^-1 cm^-2. The electrode exhibited a broad linear range of 2 µM to 9 mM and a low limit of detection (LOD) of 0.43 µM (relative standard deviation, RSD = 2.3%) at + 0.45 V vs Ag/AgCl. The excellent properties obtained for glucose detection were most likely due to the synergistic effect of the combination of individual components: poly(caffeic acid), MWCNTs, and CuO. Good accuracy and high precision were demonstrated for quantifying glucose concentrations in human serum and blood samples (the recovery ranged from 95.0 to 99.5%). The GC/PCA@MWCNT-CuO sensor represents a novel, simple, and low-cost approach to the fabrication of devices for amperometric sensing of glucose.

Non-Enzymatic Glucose Sensors Involving Copper: An Electrochemical Perspective

Non-enzymatic glucose sensors based on the use of copper and its oxides have emerged as promising candidates to replace enzymatic glucose sensors owing to their stability, ease of fabrication, and superior sensitivity. This review explains the theories of the mechanism of glucose oxidation on copper transition metal electrodes. It also presents an overview on the development of among the best non-enzymatic copper-based glucose sensors in the past 10 years. A brief description of methods, interesting findings, and important performance parameters are provided to inspire the reader and researcher to create new improvements in sensor design. Finally, several important considerations that pertain to the nano-structuring of the electrode surface is provided.

Flexible Free-Standing CuxO/Ag2O (x = 1, 2) Nanowires Integrated with Nanoporous Cu-Ag Network Composite for Glucose Sensing

To improve glucose electrocatalytic performance, one efficient manner is to develop a novel Cu-Ag bimetallic composite with fertile porosity and unique architecture. Herein, the self-supported electrode with Cu_xO/Ag₂O (x = 1, 2) nanowires grown in-situ on a nanoporous Cu-Ag network (Cu_xO/Ag₂O@NP-CuAg) has been successfully designed by a facile two-step approach. The integrated hierarchical porous structure, the tip-converged Cu_xO/Ag₂O nanowires combined with the interconnected porous conductive substrate, are favorable to provide more reactive sites and improve ions or electrons transportation. Compared with monometallic Cu₂O nanowires integrated with nanoporous Cu matrix (Cu₂O@NP-Cu), the bimetallic Cu_xO/Ag₂O@NP-CuAg composites exhibit the enhanced electrocatalytic performance for glucose. Moreover, the higher sensitivity of ~1.49 mA mM⁻¹ cm⁻² in conjunction with a wider linear range of 17 mM for the Cu_xO/Ag₂O@NP-CuAg electrode anodized for 10 min are attributed to the synergistic effect of porous structure and bimetallic Cu_xO/Ag₂O nanowires. Particularly, the integrated Cu_xO/Ag₂O@NP-CuAg composites possess good flexibility, which has been reported for the first time. Accordingly, the Cu_xO/Ag₂O@NP-CuAg with excellent glucose electrocatalytic performance and good flexibility is promising to further develop as a candidate electrode material of glucose sensors.

A nickel-cobalt bimetallic phosphide nanocage as an efficient electrocatalyst for nonenzymatic sensing of glucose

The authors describe Ni-Co bimetal phosphide (NiCoP) nanocages that exhibit enhanced electrocatalytic performance toward glucose oxidation. The nanocages offer an appealing architecture, large specific area, and good accessibility for the analyte glucose. When placed on a glassy carbon electrode, the sensor exhibits attractive figures of merit for sensing glucose in 0.1 M NaOH solution including (a) a wide linear range (0.005-7 mM), (b) a low determination limit (0.36 μM), (c) high sensitivity (6115 μA•μM^-1•cm^-2), (d) a relatively low working potential (0.50 V vs. Ag/AgCl), and (e) good selectivity, reproducibility, and stability. The sensor is successfully applied to the determination of glucose in human serum samples. Graphical abstractSchematic representation of a glassy carbon electrode modified with Ni-Co bimetal phosphide (NiCoP) nanocage. NiCoP nanocage exhibits excellent electrocatalytic activity toward glucose oxidation. NiCoP nanocage is applied in a sensitive non-enzymatic glucose sensor.

Electrochemical non-enzymatic glucose sensors: recent progress and perspectives

This review summarizes recent advances in the development of electrocatalysts for non-enzymatic glucose detection. The sensing mechanism and influencing factors are discussed, and the perspectives and challenges are also addressed.

Boosting glucose oxidation by constructing Cu–Cu2O heterostructures

An octahedral Cu–Cu₂O heterostructure with loose and porous structure was fabricated and exhibits enhanced electrocatalytic activity towards glucose oxidation.