Hybrid inorganic-organic proton-conducting membranes based on SPEEK doped with WO3 nanoparticles for application in vanadium redox flow batteries

Optimized Sulfonated Poly(Ether Ether Ketone) Membranes for In-House Produced Small-Sized Vanadium Redox Flow Battery Set-Up

The ionic exchange membranes represent a core component of redox flow batteries. Their features strongly affect the performance, durability, cost, and efficiency of these energy systems. Herein, the operating conditions of a lab-scale single-cell vanadium flow battery (VRFB) were optimized in terms of membrane physicochemical features and electrolyte composition, as a way to translate such conditions into a large-scale five-cell VRFB stack system. The effects of the sulfonation degree (SD) and the presence of a filler on the performances of sulfonated poly(ether ether ketone) (SPEEK) ion-selective membranes were investigated, using the commercial perfluorosulfonic-acid Nafion 115 membrane as a reference. Furthermore, the effect of a chloride-based electrolyte was evaluated by comparing it to the commonly used standard sulfuric acid electrolyte. Among the investigated membranes, the readily available SPEEK50-0 (SD = 50%; filler = 0%) resulted in it being permeable and selective to vanadium. Improved coulombic efficiency (93.4%) compared to that of Nafion 115 (88.9%) was achieved when SPEEK50-0, in combination with an optimized chloride-based electrolyte, was employed in a single-cell VRFB at a current density of 20 mA·cm-2. The optimized conditions were successfully applied for the construction of a five-cell VRFB stack system, exhibiting a satisfactory coulombic efficiency of 94.5%.

Block Copolymer-Based Membranes for Vanadium Redox Flow Batteries: Synthesis, Characterization, and Performance

Nonfluorinated polymers have been widely proposed to replace Nafion as raw materials for redox flow battery ion-exchange membranes. Hereby, block copolymers based on polysulfone (PSU) and polyphenylsulfone (PPSU) are synthesized and employed as precursors of membranes for vanadium redox flow batteries. A series of copolymers with varying molar proportions of PSU (75/25, 60/40, 50/50 mol %) were prepared. The 60/40 and 75/25 copolymers exhibit concentrated sulfonic groups predominantly in the PSU unit, favoring the formation of hydrophobic and hydrophilic domains. The 50/50 copolymer presents a balanced degree of sulfonation between the two units, leading to a homogeneous distribution of sulfonic groups. An ex situ study of these materials comprising vanadium ion permeability and chemical and mechanical stability was performed. The best performance is achieved with 50/50 membranes, which exhibited performance comparable to commercial Nafion membranes. These results signify a promising breakthrough in the pursuit of high-performance, sustainable membranes for next-generation VRFBs.

Implementation of Accurate Parameter Identification for Proton Exchange Membrane Fuel Cells and Photovoltaic Cells Based on Improved Honey Badger Algorithm

Predicting the system efficiency of green energy and developing forward-looking power technologies are key points to accelerating the global energy transition. This research focuses on optimizing the parameters of proton exchange membrane fuel cells (PEMFCs) and photovoltaic (PV) cells using the honey badger algorithm (HBA), a swarm intelligence algorithm, to accurately present the performance characteristics and efficiency of the systems. Although the HBA has a fast search speed, it was found that the algorithm's search stability is relatively low. Therefore, this study also enhances the HBA's global search capability through the rapid iterative characteristics of spiral search. This method will effectively expand the algorithm's functional search range in a multidimensional and complex solution space. Additionally, the introduction of a sigmoid function will smoothen the algorithm's exploration and exploitation mechanisms. To test the robustness of the proposed methodology, an extensive test was conducted using the CEC'17 benchmark functions set and real-life applications of PEMFC and PV cells. The results of the aforementioned test proved that with regard to the optimization of PEMFC and PV cell parameters, the improved HBA is significantly advantageous to the original in terms of both solving capability and speed. The results of this research study not only make definite progress in the field of bio-inspired computing but, more importantly, provide a rapid and accurate method for predicting the maximum power point for fuel cells and photovoltaic cells, offering a more efficient and intelligent solution for green energy.

Characterization of Quaternary-Ammonium-Based Ionogel Membranes for Application in Proton Exchange Membrane Fuel Cells

In recent years, the quest to advance fuel cell technologies has intensified, driven by the imperative to reduce reliance on hydrocarbon-derived fuels and mitigate pollutant emissions. Proton exchange membranes are a critical material of fuel cell technologies. The potential of ionic liquid-based polymer inclusion membranes or ionogels for proton exchange membrane fuel cells (PEMFCs) has recently appeared. Thermal stability, SEM-EDX characterization, NMR and IR characterization, thermogravimetric analysis, ion exchange capacity, and water uptake are key properties of these membranes which need to be investigated. In this work, ionogel based on quaternary ammonium salts, such as [N8,8,8,1+][Cl-], [N8,8,8,1+][Br-], and [N8-10,8-10,8-10,1+][Cl-] in various compositions with poly(vinyl chloride) are extensively studied and characterized based on those key properties. The best properties were obtained when a quaternary ammonium cation was combined with a bromide anion. Finally, ionogels are tested in microbial fuel cells. Microbial fuel cells based on the ionogel reach a maximum of 147 mW/m2, which represents 55% of the reference membrane (Nafion 212). These results indicate that we still have the possibility of improvement through the appropriate selection of the cation and anion of the ionic liquid. Overall, the promise of ionogel membranes as a viable alternative in fuel cell applications has been demonstrated.

Treatment of carbon electrodes with Ti3C2Tx MXene coating and thermal method for vanadium redox flow batteries: a comparative study

One of the significant challenges of vanadium redox flow batteries is connected to the negative electrode where the main reaction of V(ii)/V(iii) and the side reaction of hydrogen evolution compete. To address this issue, we used titanium carbide (Ti3C2Tx) MXene coating via drop-casting to introduce oxygen functional groups and metals on the carbon electrode surface. Characterization through scanning electron microscopy and X-ray photoelectron spectroscopy confirmed the even distribution of Ti3C2Tx MXene on the electrodes and the presence of titanium and termination groups (-O, -Cl, and -F). The cyclic voltammetry analysis of MXene-coated electrodes showed more sharp electrochemical peaks for the V(ii)/V(iii) reaction than thermal-treated electrodes, even at relatively high scan rates. Notably, a relatively high reaction rate of 5.61 × 10-4 cm s-1 was achieved for the V(ii)/V(iii) reaction on MXene-coated electrodes, which shows the competitiveness of the method compared to thermal treatment (4.17 × 10-4 cm s-1). The flow battery tests, at a current density of 130 mA cm-2, using MXene-coated electrodes showed pretty stable discharge capacity for over 100 cycles. In addition, the voltage and energy efficiency were significantly higher than those of the system using untreated electrodes. Overall, this work highlights the potential application of MXene coating in carbon electrode treatment for vanadium redox flow batteries due to remarkable electrocatalytic activity and battery performance, providing a competitive method for thermal treatment.

Green Synthesis of Cation Exchange Membranes: A Review

Cation exchange membranes (CEMs) play a significant role in the transition to a more sustainable/green society. They are important components for applications such as water electrolysis, artificial photosynthesis, electrodialysis and fuel cells. Their synthesis, however, is far from being sustainable, affecting safety, health and the environment. This review discusses and evaluates the possibilities of synthesizing CEMs that are more sustainable and green. First, the concepts of green and sustainable chemistry are discussed. Subsequently, this review discusses the fabrication of conventional perfluorinated CEMs and how they violate the green/sustainability principles, eventually leading to environmental and health incidents. Furthermore, the synthesis of green CEMs is presented by dividing the synthesis into three parts: sulfonation, material selection and solvent selection. Innovations in using gaseous SO3 or gas-liquid interfacial plasma technology can make the sulfonation process more sustainable. Regarding the selection of polymers, chitosan, cellulose, polylactic acid, alginate, carrageenan and cellulose are promising alternatives to fossil fuel-based polymers. Finally, water is the most sustainable solvent and many biopolymers are soluble in it. For other polymers, there are a limited number of studies using green solvents. Promising solvents are found back in other membrane, such as dimethyl sulfoxide, Cyrene™, Rhodiasolv® PolarClean, TamiSolve NxG and γ-valerolactone.

Structural Characterization and Physicochemical Properties of Functionally Porous Proton-Exchange Membrane Based on PVDF-SPA Graft Copolymers

Fluorinated proton-exchange membranes (PEMs) based on graft copolymers of dehydrofluorinated polyvinylidene fluoride (D-PVDF), 3-sulfopropyl acrylate (SPA), and 1H, 1H, 2H-perfluoro-1-hexene (PFH) were prepared via free radical copolymerization and characterized for fuel cell application. The membrane morphology and physical properties were studied via small-(SAXS) and wide-angle X-ray scattering (WAXS), SEM, and DSC. It was found that the crystallinity degree is 17% for PEM-RCF (co-polymer with SPA) and 16% for PEM-RCF-2 (copolymer with SPA and PFH). The designed membranes possess crystallite grains of 5-6 nm in diameter. SEM images reveal a structure with open pores on the surface of diameters from 20 to 140 nm. Their transport and electrochemical characterization shows that the lowest membrane area resistance (0.9 Ωcm2) is comparable to perfluorosulfonic acid PEMs (such as Nafion®) and polyvinylidene fluoride (PVDF) based CJMC cation-exchange membranes (ChemJoy Polymer Materials, China). Key transport and physicochemical properties of new and commercial membranes were compared. The PEM-RCF permeability to NaCl diffusion is rather high, which is due to a relatively low concentration of fixed sulfonate groups. Voltammetry confers that the electrochemical behavior of new PEM correlates to that of commercial cation-exchange membranes, while the ionic conductivity reveals an impact of the extended pores, as in track-etched membranes.

Study on Self-Humidification in PEMFC with Crossed Flow Channels and an Ultra-Thin Membrane

In this study, a 3D model of a proton exchange membrane fuel cell (PEMFC) with crossed channels and an ultra-thin membrane is developed to investigate the feasibility of self-humidification; experiments utilizing a PEMFC stack with identical configurations are conducted to validate the simulation results and further investigate the effects of various operating conditions (OCs) on self-humidification. The results indicate that the crossed flow channel leads to enhanced uniformity of water distribution, resulting in improved cell performance under low/no humidification conditions. External humidifiers for the anode can be removed since the performance difference is negligible (≤3%) between RHa = 0% and 100%. Self-humidification can be achieved in the stack at 90 °C or below with an appropriate back pressure among 100-200 kPa. As the current density increases, there is a gradual convergence and crossing of the voltage at low RH with that at high RH, and the crossover points are observed at 60-80 °C with suitable pressure when successful self-humidification is achieved. Below the current density of the point, the stack's performance is inferior at lower RH due to membrane unsaturation, and conversely, the performance is inferior at higher RH due to flooding; this current density decreases with higher pressure and lower temperature.

Self-Assembled Construction of Ion-Selective Nanobarriers in Electrolyte Membranes for Redox Flow Batteries

Ion-conducting membranes (ICMs) with high selectivity are important components in redox flow batteries. However it is still a challenge to break the trade-off between ion conductivity and ion selectivity, which can be resolved by the regulation of their nanostructures. Here, polyoxometalate (POM)-hybridized block copolymers (BCPs) are used as self-assembled additives to construct proton-selective nanobarriers in the ICM matrix to improve the microscopic structures and macroscopic properties of ICMs. Benefiting from the co-assembly behavior of BCPs and POMs and their cooperative noncovalent interactions with the polymer matrix, ∼50 nm ellipsoidal functional nanoassemblies with hydrophobic vanadium-shielding cores and hydrophilic proton-conducting shells are constructed in the sulfonated poly(ether ether ketone) matrix, which leads to an overall enhancement of proton conductivity, proton selectivity, and cell performance. These results present a self-assembly route to construct functional nanostructures for the modification of polymer electrolyte membranes toward emerging energy technologies.

A Comparative Study of Nafion 212 and Sulfonated Poly(Ether Ether Ketone) Membranes with Different Degrees of Sulfonation on the Performance of Iron-Chromium Redox Flow Battery

For an iron-chromium redox flow battery (ICRFB), sulfonated poly(ether ether ketone) (SPEEK) membranes with five various degrees of sulfonation (DSs) are studied. To select the SPEEK membrane with the ideal DS for ICRFB applications, the physicochemical characteristics and single-cell performance are taken into consideration. Following all the investigations, it has been determined that the SPEEK membrane, which has a DS of 57% and a thin thickness of 25 μm, is the best option for replacing commercial Nafion 212 in ICRFB. Firstly, it exhibits a better cell performance according to energy efficiency (EE) and coulombic efficiency (CE) at the current density range between 40 mA cm-2 and 80 mA cm-2. Additionally, it has a more stable EE (79.25-81.64%) and lower discharge capacity decay rate (50%) than the Nafion 212 (EE: 76.74-81.45%, discharge capacity decay: 76%) after 50 charge-discharge cycles, which proves its better oxidation stability as well. In addition, the longer self-discharge time during the open-circuit voltage test further demonstrates that this SPEEK membrane could be employed for large-scale ICRFB applications.

Anion Exchange Membranes Based on Chemical Modification of Recycled PET Bottles

This study presents an innovative and effective solution for recycling PET bottles as raw for producing anion exchange membranes (AEMs) for electrochemical applications. This approach reduces the demand for pristine materials, a key principle of the circular economy and sustainability. PET was subjected to chemical modification by introducing cationic functional groups followed by methylation and OH- exchange process. The amination synthesis was optimized based on reaction time. The results indicate that ion exchange capacity, water uptake, and swelling ratio properties mainly depend on the degree of cationic functionalization. The optimized AEM exhibits ionic conductivity of 5.3 × 10-2 S·cm-1 and alkaline stability of 432 h in 1 M KOH at 80 °C. The membrane properties before and after the alkaline treatment were investigated using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy analysis. Computational chemistry analysis was employed to gain further insights into the membrane degradation mechanisms and pathways under alkaline conditions. This research and its findings are a step toward using recycled materials in the field of AEM technology.

Low-cost Zinc-Iron Flow Batteries for Long-Term and Large-Scale Energy Storage

Aqueous flow batteries are considered very suitable for large-scale energy storage due to their high safety, long cycle life, and independent design of power and capacity. Especially, zinc-iron flow batteries have significant advantages such as low price, non-toxicity, and stability compared with other aqueous flow batteries. Significant technological progress has been made in zinc-iron flow batteries in recent years. Numerous energy storage power stations have been built worldwide using zinc-iron flow battery technology. This review first introduces the developing history. Then, we summarize the critical problems and the recent development of zinc-iron flow batteries from electrode materials and structures, membranes manufacture, electrolyte modification, and stack and system application. Finally, we forecast the development direction of the zinc-iron flow battery technology for large-scale energy storage.

Modified Membranes for Redox Flow Batteries-A Review

In this review, the state of the art of modified membranes developed and applied for the improved performance of redox flow batteries (RFBs) is presented and critically discussed. The review begins with an introduction to the energy-storing chemical principles and the potential of using RFBs in the energy transition in industrial and transport-related sectors. Commonly used membrane modification techniques are briefly presented and compared next. The recent progress in applying modified membranes in different RFB chemistries is then critically discussed. The relationship between a given membrane modification strategy, corresponding ex situ properties and their impact on battery performance are outlined. It has been demonstrated that further dedicated studies are necessary in order to develop an optimal modification technique, since a modification generally reduces the crossover of redox-active species but, at the same time, leads to an increase in membrane electrical resistance. The feasibility of using alternative advanced modification methods, similar to those employed in water purification applications, needs yet to be evaluated. Additionally, the long-term stability and durability of the modified membranes during cycling in RFBs still must be investigated. The remaining challenges and potential solutions, as well as promising future perspectives, are finally highlighted.

Improving PFSA Membranes Using Sulfonated Nanodiamonds

Aquivion®-type perfluorosulfonic acid membranes with a polytetrafluoroethylene backbone and short side chains with sulfonic acid groups at the ends have great prospects for operating in hydrogen fuel cells. To improve the conducting properties of membranes, various types of nanofillers can be used. We prepared compositional Aquivion®-type membranes with embedded detonation nanodiamond particles. Nanodiamonds were chemically modified with sulfonic acid groups to increase the entire amount of ionogenic groups involved in the proton conductivity mechanism in compositional membranes. We demonstrated the rise of proton conductivity at 0.5-2 wt.% of sulfonated nanodiamonds in membranes, which was accompanied by good mechanical properties. The basic structural elements, conducting channels in membranes, were not destroyed in the presence of nanodiamonds, as follows from small-angle neutron scattering data. The prepared compositional membranes can be used in hydrogen fuel cells to achieve improved performance.

Composite Membrane for Sodium Polysulfide Hybrid Redox Flow Batteries

Non-aqueous redox flow batteries (NARFBs) using earth-abundant materials, such as sodium and sulfur, are promising long-duration energy storage technologies. NARFBs utilize organic solvents, which enable higher operating voltages and potentially higher energy densities compared with their aqueous counterparts. Despite exciting progress throughout the past decade, the lack of low-cost membranes with adequate ionic conductivity and selectivity remains as one of the major bottlenecks of NARFBs. Here, we developed a composite membrane composed of a thin (<25 µm) Na+-Nafion coating on a porous polypropylene scaffold. The composite membrane significantly improves the electrochemical stability of Na+-Nafion against sodium metal, exhibiting stable Na symmetric cell performance for over 2300 h, while Na+-Nafion shorted by 445 h. Additionally, the composite membrane demonstrates a higher room temperature storage modulus than the porous polypropylene scaffold and Na+-Nafion separately while maintaining high Na+ conductivity (0.24 mS/cm at 20 °C). Our method shows that a composite membrane utilizing Na+-Nafion is a promising approach for sodium-based hybrid redox flow batteries.

Numerical Study on Thermal Stress of High Temperature Proton Exchange Membrane Fuel Cells during Start-Up Process

High-temperature proton-exchange membrane fuel cells (HT-PEMFCs) with phosphoric-doped polybenzimidazole (PBI) membranes have a higher operating temperature compared to the PEMFCs operating below 373.15 K. The fuel cell is first heated from room temperature to the minimum operating temperature to avoid the generation of liquid water. The existence of liquid water can result in the loss of phosphoric acid and then affect the cell performance. In this study, the start-up process of HT-PEMFCs is numerically studied by establishing a three-dimensional non-isothermal mathematical model. Preheated gas is supplied into gas flow channels to heat the fuel cell, and then voltage load is applied to accelerate the start-up process. Effects of voltage (0.9 V, 0.7 V and 0.5 V) and flow arrangement (co-flow and counter flow) on temperature, current density, proton conductivity and stress distributions of fuel cells are examined. It is found that the maximum stress is increased when a lower voltage is adopted, and the counter-flow arrangement provides a more uniform stress distribution than that of co-flow arrangement.

Effect of TiO2 and Al2O3 Addition on the Performance of Chitosan/Phosphotungstic Composite Membranes for Direct Methanol Fuel Cells

Composite chitosan/phosphotungstic acid (CS/PTA) with the addition of TiO₂ and Al₂O₃ particles were synthesized to be used as proton exchange membranes in direct methanol fuel cells (DMFCs). The influence of fillers was assessed through X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, liquid uptake, ion exchange capacity and methanol permeability measurements. The addition of TiO₂ particles into proton exchange membranes led to an increase in crystallinity and a decrease in liquid uptake and methanol permeability with respect to pristine CS/PTA membranes, whilst the effect of the introduction of Al₂O₃ particles on the characteristics of membranes is almost the opposite. Membranes were successfully tested as proton conductors in a single module DMFC of 1 cm² as active area, operating at 50 °C fed with 2 M methanol aqueous solution at the anode and oxygen at the cathode. Highest performance was reached by using a membrane with TiO₂ (5 wt.%) particles, i.e., a power density of 40 mW cm^-2, almost doubling the performance reached by using pristine CS/PTA membrane (i.e., 24 mW cm^-2).

Assessment of Dye-Absorbed Eggshell Membrane Composites as Solid Polymer Electrolyte of Fuel Cells

Recently, polymer electrolytes have been developed for high-performance and eco-friendly fuel cells. Among the candidates, eggshell membrane (ESM) has been promising because of its abundance to assemble various energy devices with low cost and its absorption ability of organic materials. In this work, we investigated fuel cells that included ESM-absorbing xanthene-, triphenylmethane-, and azo-type tar dye, which contained abundant hydrophilic groups, as polymer electrolytes. We found out two points: (1) that the fuel cells that included ESM-absorbing xanthene-type dye generated the highest I-V performance, and (2) the basic molecular structures of the tar dyes determined the correlation of the maximum power and proton conductivities.

Design and Utilization of a Direct Methanol Fuel Cell

This study introduces a step-by-step, summarized overview of direct methanol fuel cell (DMFC) fundamentals, thermodynamic-electrochemical principles, and system evaluation factors. In addition, a parametric investigation of a JENNY 600S DMFC is conducted to simulate cell performance behavior under varying operating conditions. The system is mathematically modeled and solved in MATLAB and accounts for multi-irreversibilities such as the activation and ohmic and concentration overpotentials. The performance of the modeled system was validated against theoretical and experimental results from the literature. The results indicated that increasing the fuel cell's operating temperature yields enhanced output cell voltages due to enhanced methanol oxidation reactions. Nevertheless, the maximum efficiency limits of the fuel cell tend to decrease with an increase in temperature. In addition, the model has also depicted that enhanced output cell voltages are associated with increased oxygen consumption, resulting in the lower exit flowrates of the reactants.

Efficiency Analysis of Fuel Cell Components with Ionic Poly-Arylether Composite Membrane

We use polyethylene glycol as an additive to explore how the hydrogen bonding of this additive changes the properties of SA8 blended sulfonated polyetheretherketone (SPEEK) composite films. We mixed a 5%wt polyethylene glycol solution into a 12.5%wt SA8 solution, and then prepared a film with a total weight of 40 g at a ratio of 1:99. The SA8 (PEG) solution was prepared and then mixed with 5%wt SPEEK solution, and a film-forming solution with a total weight of 8g in different mixing ratios was created. Polyethylene glycol (PEG) was mixed into the sulfonated polyarylether polymer SA8 to form physical cross-linking. Therefore, the sulfonated polyether ether ketone SPEEK was mixed in, and it exhibited good thermal stability and dimensional stability. However, there was some decrease in proton conductivity as the proportion of SPEEK increased. Although SPEEK mixed with sulfonated polymer reduces the proton conductivity, the physical cross-linking of PEG can improve the proton conductivity of the composite membrane, and adding SPEEK can not only solve the problem of the high sulfonation film swelling phenomenon, it can also improve the dimensional stability of the film through the hydrogen bonding force of PEG and obtain a composite film with excellent properties.

Current Distribution in the Discharge Unit of a 10-Cell Vanadium Redox Flow Battery: Comparison of the Computational Model with Experiment

Shunting currents are among the main problems of all-vanadium redox flow battery stacks since, in addition to capacity losses, they cause negative effects associated with the local destruction of electrodes and bipolar plates. The values of both the shunting currents and their destructive effects on materials can be reduced at the battery development stage by adjusting the resistance of the electrolyte supply channels. The solution to this problem can be found using a calculation model for current distribution based on the current balance in the nodes as well as voltage drops and electromotive force in internal circuits according to Kirchhoff's laws. This paper presents the verification of the model of current distribution in an all-vanadium redox flow battery stack of an original design that allows for the determination of membrane-electrode assembly resistances and electrolyte supply channels via direct measurements. Based on a comparison of the calculated and experimental values of the coulombic efficiency of charge-discharge cycles, the capacity fade associated with the crossover of vanadium compounds through the membrane has been determined.

Research Progress, Trends, and Current State of Development on PEMFC-New Insights from a Bibliometric Analysis and Characteristics of Two Decades of Research Output

The consumption of hydrogen could increase by sixfold in 2050 compared to 2020 levels, reaching about 530 Mt. Against this backdrop, the proton exchange membrane fuel cell (PEMFC) has been a major research area in the field of energy engineering. Several reviews have been provided in the existing corpus of literature on PEMFC, but questions related to their evolutionary nuances and research hotspots remain largely unanswered. To fill this gap, the current review uses bibliometric analysis to analyze PEMFC articles indexed in the Scopus database that were published between 2000-2021. It has been revealed that the research field is growing at an annual average growth rate of 19.35%, with publications from 2016 to 2012 alone making up 46% of the total articles available since 2000. As the two most energy-consuming economies in the world, the contributions made towards the progress of PEMFC research have largely been from China and the US. From the research trend found in this investigation, it is clear that the focus of the researchers in the field has largely been to improve the performance and efficiency of PEMFC and its components, which is evident from dominating keywords or phrases such as 'oxygen reduction reaction', 'electrocatalysis', 'proton exchange membrane', 'gas diffusion layer', 'water management', 'polybenzimidazole', 'durability', and 'bipolar plate'. We anticipate that the provision of the research themes that have emerged in the PEMFC field in the last two decades from the scientific mapping technique will guide existing and prospective researchers in the field going forward.

Characterization of Commercial Polymer-Carbon Composite Bipolar Plates Used in PEM Fuel Cells

Bipolar plates represent a crucial component of the PEM fuel cell stack. Polymer-carbon composites are recognized as state-of-the-art materials for bipolar plate manufacturing, but their use involves a compromise between electrical and heat conductivity, mechanical strength and costs. Thus, all key parameters must be considered when selecting a suitable plate satisfying the demands of the desired application. However, data relevant to commercial materials for such selection are scarce in the open literature. To address this issue, 13 commercially available polymer-carbon composites are characterised in terms of the following parameters: through-plane conductivity, hydrogen permeability, mechanical strength, water uptake, density, water contact angle and chemical stability. None of the materials tested reached the DOE target for electrical conductivity, while five of the materials met the target for flexural strength. The overall best-performing material showed a conductivity value of 50.4 S·cm^-1 and flexural strength of 40.1 MPa. The data collected provide important supporting information in selecting the materials most suitable for the desired application. In addition, the key parameters determined for each bipolar plate supply important input parameters for the mathematical modelling of fuel cells.

Electrochemical Measurement of Interfacial Distribution and Diffusion Coefficients of Electroactive Species for Ion-Exchange Membranes: Application to Br2/Br- Redox Couple

A novel method has been proposed for rapid determination of principal transmembrane transport parameters for solute electroactive co-ions/molecules, in relation to the crossover problem in power sources. It is based on direct measurements of current for the electrode, separated from solution by an ion-exchange membrane, under voltammetric and chronoamperometric regimes. An electroactive reagent is initially distributed within the membrane/solution space under equilibrium. Then, potential change induces its transformation into the product at the electrode under the diffusion-limited regime. For the chronoamperometric experiment, the electrode potential steps backward after the current stabilization, thus inducing an opposite redox transformation. Novel analytical solutions for nonstationary concentrations and current have been derived for such two-stage regime. The comparison of theoretical predictions with experimental data for the Br₂/Br^- redox couple (where only Br^- is initially present) has provided the diffusion coefficients of the Br^- and Br₂ species inside the membrane, D(Br^-) = (2.98 ± 0.27) 10^-6 cm²/s and D(Br₂) = (1.10 ± 0.07) 10^-6 cm²/s, and the distribution coefficient of the Br^- species at the membrane/solution boundary, K(Br^-) = 0.190 ± 0.005, for various HBr additions (0.125-0.75 M) to aqueous 2 M H₂SO₄ solution. This possibility to determine transport characteristics of two electroactive species, the initial solute component and its redox product, within a single experiment, represents a unique feature of this study.

Electric Field-Assisted Filling of Sulfonated Polymers in ePTFE Backing Material for Fuel Cell

This study fabricated a composite ePTFE-backed proton-exchange membrane by filling the pores on the ePTFE backing with sulfonated polyarylene ethers through an externally supplied electric field. The morphology changes were observed under an SEM. The results suggested that the application of an electric field had led to the effective filling of pores by polymers. In addition, the composite membrane featured good dimensional stability and swelling ratio, and its water uptake, proton conductivity and component efficiency increased with voltage. It is found in this study that the external application of an electric field resulted in the effective filling of pores in the ePTFE by sulfonated polyarylene ether polymers and, thus, an improved composite membrane performance.

Synthesis of Anion Exchange Membranes Containing PVDF/PES and Either PEI or Fumion®

In this work, the preparation of dense blended membranes, from blends of poly(vinylidene fluoride) (PVDF), poly(ether sulfone) (PES) and polyethyleneimine (PEI) or Fumion^®, with possible applications in alkaline fuel cell (AEMFC) is reported. The blended PEI/Fumion^® membranes were prepared under a controlled air atmosphere by a solvent evaporation method, and were characterized regarding water uptake, swelling ratio, thermogravimetric analysis (TGA), infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), ion exchange capacity (IEC), OH^- conductivity and novel hydroxide ion exchange rate (HIER), which is related to the mass transport capacity of the OH^- ions through the membrane. The effect of the chemical composition on its morphological and anion exchange properties was evaluated. It was expected that the usage of a commercial ionomer Fumion^®, in the blended membranes would result in better features in the electrical/ionic conductivity behaviour. However, two of the membranes containing PEI exhibited a higher HIER and OH^- conductivity than Fumion^® membranes, and were excellent option for potential applications in AEMFC, considering their performance and the cost of Fumion^®-based membranes.

A Brief Review of Poly(Vinyl Alcohol)-Based Anion Exchange Membranes for Alkaline Fuel Cells

Anion exchange membrane fuel cells have unique advantages and are thus gaining increasing attention. Poly(vinyl alcohol) (PVA) is one of the potential polymers for the development of anion exchange membranes. This review provides recent studies on PVA-based membranes as alternative anion exchange membranes for alkaline fuel cells. The development of anion exchange membranes in general, including the types, materials, and preparation of anion exchange membranes in the last years, are discussed. The performances and characteristics of recently reported PVA-based membranes are highlighted, including hydroxide conductivity, water uptake, swelling degree, tensile strength, and fuel permeabilities. Finally, some challenging issues and perspectives for the future study of anion exchange membranes are discussed.

Enhancement of the Green H2 Production by Using TiO2 Composite Polybenzimidazole Membranes

This study reports the hydrogen production using TiO2 based composite polybenzimidazole membranes through the SO2 depolarized electrolysis that requires lower energy input than the direct water electrolysis. Composite membranes prepared and studied in this work showed very promising results in terms of proton conductivity, chemical stability, and crossover. Thus, a reduction in SO2 crossover was observed with the increase of the concentration of TiO2, obtaining reductions as high as 42% with the 3.0 wt% TiO2-PBI membrane at 120 °C. Higher hydrogen production rates and Faradaic efficiencies were achieved by all the composite membranes, with an optimum for the 1.0 wt% TiO2-PBI membrane (with this membrane, the production of hydrogen increased a 53% at 110 °C and a 49% at 120 °C as compared with the standard PBI membrane), demonstrated the benefit of the use of composite membranes with respect to the standard one for green hydrogen production.

Bromine Crossover in Operando Analysis of Proton Exchange Membranes in Hydrogen-Bromate Flow Batteries

The manuscript deals with the fundamental problem of platinum hydrogen oxidation catalyst poisoning of the hybrid chemical power source based on bromate electroreduction and hydrogen electro-oxidation reactions. The poisoning is caused by the crossover of bromine-containing species through the proton exchange membrane separating compartments of the flow cell. Poisoning results in a drastic decrease in the flow cell performance. This paper describes the results of the direct measurement of bromine-containing species' crossover through perfluorosulfonic acid membranes of popular vendors in a hydrogen-bromate flow cell and proposes corresponding scenarios for the flow battery charge-discharge operation based on the electrolyte's control of the pH value. The rate of the crossover of the bromine-containing species through the membrane is found to be inversely proportional to the membrane thickness.

Work Efficiency and Economic Efficiency of Actual Driving Test of Proton Exchange Membrane Fuel Cell Forklift

A 3.5 tonne forklift containing proton exchange membrane fuel cells (PEMFCs) and lithium-ion batteries was manufactured and tested in a real factory. The work efficiency and economic applicability of the PEMFC forklift were compared with that of a lithium-ion battery-powered forklift. The results showed that the back-pressure of air was closely related to the power density of the stack, whose stability could be improved by a reasonable control strategy and membrane electrode assemblies (MEAs) with high consistency. The PEMFC powered forklift displayed 40.6% higher work efficiency than the lithium-ion battery-powered forklift. Its lower use-cost compared to internal engine-powered forklifts, is beneficial to the commercialization of this product.

Safe Ventilation Methods against Leaks in Hydrogen Fuel Cell Rooms in Homes

Hydrogen, which has a high energy density and does not emit pollutants, is considered an alternative energy source to replace fossil fuels. Herein, we report an experimental study on hydrogen leaks and ventilation methods for preventing damage caused by leaks from hydrogen fuel cell rooms in homes, among various uses of hydrogen. This experiment was conducted in a temporary space with a volume of 11.484 m3. The supplied pressure, leak-hole size, and leakage amount were adjusted as the experimental conditions. The resulting hydrogen concentrations, which changed according to the operation of the ventilation openings, ventilation fan, and supplied shutoff valve, were measured. The experimental results showed that the reductions in the hydrogen concentration due to the shutoff valve were the most significant. The maximum hydrogen concentration could be reduced by 80% or more if it is 100 times that of the leakage volume or higher. The shutoff valve, ventilation fan, and ventilation openings were required to reduce the concentrations of the fuel cell room hydrogen in a spatially uniform manner. Although the hydrogen concentration in a small hydrogen fuel cell room for home use can rapidly increase, a rapid reduction in the concentration of hydrogen with an appropriate ventilation system has been experimentally proven.

Numerical Parametric Investigation of Nonaqueous Vanadium Redox Flow Batteries

Nonaqueous redox flow batteries are promising candidates for large-scale energy storage technologies. However, the effect of structural design and key factors limiting the performance are still not thoroughly understood. In this work, we constructed a physical model to study the effect of various design parameters on the performance of such a battery. It was found that the kinetics of redox reaction was improved with active material concentration and electrode surface area. The modeling results also showed that the local current density was much higher in the vicinity of membrane than near the current collector due to relatively low ionic conductivity of electrolytes. Furthermore, decreasing the electrode thickness and increasing the membrane conductivity both reduced the voltage loss associated with ohmic resistance, thereby resulting in improved battery performance. The obtained numerical simulation results would be helpful not only for understanding the physicochemical process in nonaqueous vanadium flow batteries but also for future structural optimization of these batteries.

Carbon-Free Electricity Generation in Spain with PV–Storage Hybrid Systems

Climate change motivated by human activities constitutes one of the main challenges of this century. To cut carbon emissions in order to mitigate carbon’s dangerous effects, the current energy generation mix should be shifted to renewable sources. The main drawback of these technologies is their intermittency, which will require energy storage systems to be fully integrated into the generation mix, allowing them to be more controllable. In recent years, great progress to develop an effective and economically feasible energy storage systems, particularly motivated by the recent rise of demand for electric transportation, has been made. Lithium-ion (Li-ion) battery prices have fallen near 90% over the past decade, making possible the affordability of electric vehicles and transforming the economics of renewable energy. In this work, a study on storage capacity demand previously presented as conference paper is expanded, including a deep analysis of the Spanish generation mix, the evaluation of the energy storage requirements for different low-carbon and carbon-free scenarios in Mainland Spain, and the calculation of the CO2 emissions’ reduction and the associated storage costs.

Cellulose Nanocrystals Crosslinked with Sulfosuccinic Acid as Sustainable Proton Exchange Membranes for Electrochemical Energy Applications

Nanocellulose is a sustainable material which holds promise for many energy-related applications. Here, nanocrystalline cellulose is used to prepare proton exchange membranes (PEMs). Normally, this nanomaterial is highly dispersible in water, preventing its use as an ionomer in many electrochemical applications. To solve this, we utilized a sulfonic acid crosslinker to simultaneously improve the mechanical robustness, water-stability, and proton conductivity (by introducing -SO₃⁻H⁺ functional groups). The optimization of the proportion of crosslinker used and the crosslinking reaction time resulted in enhanced proton conductivity up to 15 mS/cm (in the fully hydrated state, at 120 °C). Considering the many advantages, we believe that nanocellulose can act as a sustainable and low-cost alternative to conventional, ecologically problematic, perfluorosulfonic acid ionomers for applications in, e. fuel cells and electrolyzers.

Development of WO3-Nafion Based Membranes for Enabling Higher Water Retention at Low Humidity and Enhancing PEMFC Performance at Intermediate Temperature Operation

The proton exchange membrane (PEM) represents a pivotal material and a key challenge in developing fuel cell science and hydrogen technology. Nafion is the most promising polymer which will lead to its commercialisation. Hybrid membranes of nanosized tungsten oxide (WO₃) and Nafion were fabricated, characterised, and tested in a single cell. The incorporation of 10 wt% WO₃ resulted in 21% higher water uptake, 11.7% lower swelling ratio, almost doubling the hydration degree, and 13% higher mechanical stability of the hybrid membrane compared to the Nafion XL. Compared to commercial Nafion XL, the rNF-WO-10 hybrid membrane showed an 8.8% and 20% increase in current density of the cell at 0.4 V operating at 80 and 95 °C with 1.89 and 2.29 A/cm², respectively. The maximum power density has increased by 9% (0.76 W/cm²) and 19.9% (0.922 W/cm²) when operating at the same temperatures compared to the commercial Nafion XL membrane. Generally, considering the particular structure of Nafion XL, our Nafion-based membrane with 10 wt% WO₃ (rNF-WO-10) is a suitable PEM with a comparable performance at different operating conditions.

Water Treatment Using High Performance Antifouling Ultrafiltration Polyether Sulfone Membranes Incorporated with Activated Carbon

Membrane fouling is a continued critical challenge for ultrafiltration membranes performance. In this work, polyether sulfone (PES) ultrafiltration (UF) membranes were fabricated via phase-inversion method by incorporating varying concentrations of APTMS modified activated carbon (mAC). The mAC was thoroughly characterized and the fabricated membranes were studied for their surface morphology, functional groups, contact angle, water retention, swelling (%) porosity, and water flux. The hydrophilicity of mAC membranes also resulted in lower contact angle and higher values of porosity, roughness, water retention as well as water flux. Also, the membranes incorporated with mAC exhibited antibacterial performance against model test strains of gram-negative Ecoil and gram-positive S. aureus. The antifouling studies based on bovine serum albumin protein (BSA) solution filtration showed that mAC membranes have better BSA flux. The higher flux and antifouling characteristics of the mAC membranes were attributed to the electrostatic repulsion of the BSA protein from the unique functional properties of AC and network structure of APTMS. The novel mAC ultrafiltration membranes developed and studied in present work can provide higher flux and less BSA rejection thus can find antifouling applications for the isolation and concentration of proteins and macromolecules.

Ionomer Membranes Produced from Hexaarylbenzene-Based Partially Fluorinated Poly(arylene ether) Blends for Proton Exchange Membrane Fuel Cells

In this study, a series of high molecular weight ionomers of hexaarylbenzene- and fluorene-based poly(arylene ether)s were synthesized conveniently through condensation and post-sulfonation modification. The use a of blending method might increase the stacking density of chains and affect the formation both of interchain and intrachain proton transfer clusters. Multiscale phase separation caused by the dissolution and compatibility differences of blend ionomer in high-boiling-point solvents was examined through analysis and simulations. The blend membranes produced in this study exhibited a high proton conductivity of 206.4 mS cm−1 at 80 °C (increased from 182.6 mS cm−1 for precursor membranes), excellent thermal resistance (decomposition temperature > 200 °C), and suitable mechanical properties with a tensile strength of 73.8−77.4 MPa. As a proton exchange membrane for fuel cell applications, it exhibits an excellent power efficiency of approximately 1.3 W cm−2. Thus, the ionomer membranes have strong potential for use in proton exchange membrane fuel cells and other electrochemical applications.

Spectroscopy and Cyclic Voltammetry Properties of SPEEK/CuO Nanocomposite at Screen-Printed Gold Electrodes

A successful electrochemical study of copper oxide nanoparticles (CuO NPs), sulfonated poly (ether ether ketone) polymer (SPEEK), and sulfonated polyether ether ketone-copper oxide (SPEEK/CuO) nanocomposite on bare gold electrodes was conducted. The synthesized CuO NPs and SPEEK/CuO nanocomposite were characterized using X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV–Vis), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and electron dispersive spectroscopy (EDS). The XRD showed that the diameter of the CuO NPs synthesized was 20.44 nm. The cyclic voltammetry properties of bare screen-print gold, SPEEK and SPEEK/CuO-modified electrodes were assessed in a 5 mM K₃[Fe(CN)₆] solution. The electrochemical performance of the fabricated electrodes investigated revealed that CuO NPs improved the electrochemical properties of SPEEK, and the quantum size effect indicated good adsorption by the SPEEK/CuO nanocomposite compared to the SPEEK polymer and the CuO NPs alone. Moreover, the Tafel values indicated the enhanced electrochemical performance of the other electrodes as compared with the SPEEK/CuO nanocomposite. This, therefore, confirmed the successful incorporation of CuO NPs into the SPEEK polymer, as the increased surface area and the interactions between the polymer matrix and CuO fillers improved the electrochemical performance of the electrode.

Optimization of Large-Scale Battery Storage Capacity in Conjunction with Photovoltaic Systems for Maximum Self-Sustainability

The photovoltaic array has gained popularity in the global electrical market. At the same time, battery storage, which is recently being placed by energy consumers alongside photovoltaics, continues to fall in price. Domestic and community loads may be combined utilizing central battery storage and shared solar power through an integrated grid or microgrid system. One of the main targets is maximum self-sustainability and independence of the microgrid system and implemented solution. This research study looks at the energy flows in a single household system that includes solar arrays and battery storage. The analysed household system is represented by a model which uses real load profiles from experimental measurements, local solar distribution, and onsite weather data. The results show that depending on the system configuration, two important parameters, self-consumption and self-sufficiency, can vary significantly. For a properly designed photovoltaic system, the energy self-consumption can be up to 90.19%, while self-sufficiency can be up to 82.55% for analysed cases. As an outcome, a large sample size with a variety of setups is recommended for a thorough examination of self-sustainability. Regional variations can worsen under different weather conditions, different photovoltaic and battery capacities, and different municipal rules.

Intelligent and Optimized Microgrids for Future Supply Power from Renewable Energy Resources: A Review

Using renewable energy sources instead of fossil fuels is one of the best solutions to overcome greenhouse gas (GHG) emissions. However, in designing clean power generation microgrids, the economic aspects of using renewable energy technologies should be considered. Furthermore, due to the unpredictable nature of renewable energy sources, the reliability of renewable energy microgrids should also be evaluated. Optimized hybrid microgrids based on wind and solar energy can provide cost-effective power generation systems with high reliability. These microgrids can meet the power demands of the consuming units, especially in remote areas. Various techniques have been used to optimize the size of power generation systems based on renewable energy to improve efficiency, maintain reliability, improve the power grid’s resilience, and reduce system costs. Each of these techniques has shown its advantages and disadvantages in optimizing the size of hybrid renewable energy systems. To increase the share of renewable energies in electricity supply in the future and develop these new technologies further, this paper reviews the latest and most efficient techniques used to optimize green microgrids from an economical and reliable perspective to achieve a clean, economical, and highly reliable microgrid.

Elucidating the Water and Methanol Dynamics in Sulfonated Polyether Ether Ketone Nanocomposite Membranes Bearing Layered Double Hydroxides

Conventional Nafion membranes demonstrate a strong affinity for methanol, resulting in a high fuel crossover, poor mechanical stability, and thus poor performance in direct methanol fuel cells (DMFCs). This study involves the synthesis and physiochemical characterization of an alternative polymer electrolyte membrane for DMFCs based on sulfonated poly(ether ether ketone) and a layered double hydroxide (LDH) material. Nanocomposite membranes (sPL), with filler loading ranging between 1 wt% and 5 wt%, were prepared by simple solution intercalation and characterized by XRD, DMA, swelling tests, and EIS. For the first time, water and methanol mobility inside the hydrophilic channels of sPEEK-LDH membranes were characterized by NMR techniques. The introduction of LDH nanoplatelets improved the dimensional stability while having a detrimental effect on methanol mobility, with its self-diffusion coefficient almost two orders of magnitude lower than that of water. It is worth noting that anionic lamellae are directly involved in the proton transport mechanism, thus enabling the formation of highly interconnected paths for proton conduction. In this regard, sPL₃ yielded a proton conductivity of 110 mS cm⁻¹ at 120 °C and 90% RH, almost attaining the performance of the Nafion benchmark. The nanocomposite membrane also showed an excellent oxidative stability (over more than 24 h) during Fenton’s test at 80 °C. These preliminary results demonstrate that an sPL₃ nanocomposite can be potentially and successfully applied in DMFCs.

Robust Adamantane-Based Membranes with Enhanced Conductivity for Vanadium Flow Battery Application

Membranes with high conductivity, high selectivity, and high stability are urgently needed for high-power-density vanadium flow batteries (VFBs). Enhancing membrane conductivity presents many challenges, often resulting in sacrificing membrane selectivity and mechanical strength. To overcome this, new robust adamantane-based membranes with enhanced conductivity are constructed for VFB. Low-content basic piperazine (IEC = 0.78 mmol g⁻¹) and hydrophilic hydroxyl groups are introduced into highly rigid, hydrophobic adamantane containing poly(aryl ether ketone) backbone (PAPEK) and then selectively swelled to induce microphase separation and form ion transport pathways. The highly rigid and hydrophobic PAPEK exhibits high swelling resistance and provides the membranes with slight swelling, high selectivity, and high mechanical strength. The selective swelling temperature has a significant influence on the areal resistance of the resulting membrane, e.g., the PAPEK-130 membrane, when selectively swelled at 130 °C, has low areal resistance (0.22 Ω∙cm²), which is approximately two-fifths that of the PAEKK-60 membrane (treated at 60 °C, 0.57 Ω∙cm²). Consequently, the resulting PAPEK membranes exhibit low swelling, high selectivity, and low areal resistance, with the VFB constructed with a PAPEK-90 membrane exhibiting excellent energy efficiency (91.7%, at 80 mA∙cm⁻², and 80.0% at 240 mA∙cm⁻²) and stable cycling performance for 2000 cycles.

Microbial Electrolysis Cell as a Diverse Technology: Overview of Prospective Applications, Advancements, and Challenges

Microbial electrolysis cells (MECs) have been explored for various applications, including the removal of industrial pollutants, wastewater treatment chemical synthesis, and biosensing. On the other hand, MEC technology is still in its early stages and faces significant obstacles regarding practical large-scale implementations. MECs are used for energy generation and hydrogen peroxide, methane, hydrogen/biohydrogen production, and pollutant removal. This review aimed to investigate the aforementioned uses in order to better understand the different applications of MECs in the following scenarios: MECs for energy generation and recycling, such as hydrogen, methane, and hydrogen peroxide; contaminant removal, particularly complex organic and inorganic contaminants; and resource recovery. MEC technology was examined in terms of new concepts, configuration optimization, electron transfer pathways in biocathodes, and coupling with other technologies for value-added applications, such as MEC anaerobic digestion, combined MEC–MFC, and others. The goal of the review was to help researchers and engineers understand the most recent developments in MEC technologies and applications.

The Application of a Modified Polyacrylonitrile Porous Membrane in Vanadium Flow Battery

Vanadium flow battery (VFB) is one of the most promising candidates for large-scale energy storage. A modified polyacrylonitrile (PAN) porous membrane is successfully applied in VFB. Herein, a simple solvent post-processing method is presented to modify PAN porous membranes prepared by the traditional nonsolvent induced phase separation (NIPS) method. In the design, polymer PAN is chosen as the membrane material owing to its low cost and high stability. The large-size pores from NIPS method are well optimized by the solvent swelling and shrinking during the solvent post-processing. Meanwhile, the interconnectivity of pores is maintained well. As a result, the ion selectivity of PAN porous membranes is dramatically improved, and the CE of a VFB with PAN porous membranes rises from 68% to 93% after the solvent post-processing process. A VFB with the modified PAN porous membranes is capable of delivering a limiting current density of 900 mA cm⁻², and a high peak power density of 650 mW cm⁻², which is very competitive among the various flow batteries.

Review on Material and Design of Anode for Microbial Fuel Cell

Microbial Fuel Cell (MFC) is a bio-electrochemical system that generates electricity by anaerobic oxidation of substrates. An anode is the most critical component because the primary conversion of wastewater into electrons and protons takes place on the surface of the anode, where a biofilm is formed. This paper describes the essential properties of the anode and classifies its types according to the material used to make it. Anode material is responsible for the flow of electrons generated by the microorganism; hence biocompatibility and conductivity can considered to be the two most important properties. In this paper, the various modification strategies to improve the performance of anodes of MFC are explained through the review of researchers’ published work in this field. The shape and size of the anode turned out to be very significant as the microbial growth depends on the available surface area. The attachment of biofilm on the surface of an anode largely depends on the interfacial surface chemistry. Methods for improving MFC performance by altering the anode material, architecture, biocompatibility, and longevity are discussed with a future perspective giving special importance to the cost.

A Review on Peak Load Shaving in Microgrid—Potential Benefits, Challenges, and Future Trend

This study aims to review the potential benefits of peak load shaving in a microgrid system. The relevance of peak shaving for a microgrid system is presented in this research review at the outset to justify the peak load shaving efficacy. The prospective benefits of peak shaving in microgrid systems, including technological, economic, and environmental advantages, are thoroughly examined. This review study also presents a cost–benefit numerical analysis to illustrate the economic viability of peak load shaving for a microgrid system. Different peak shaving approaches are briefly discussed, as well as the obstacles of putting them into practice. Finally, this review study reveals some potential future trends and possible directions for peak shaving research in microgrid systems. This review paper lays a strong foundation for identifying the potential benefits of peak shaving in microgrid systems and establishing suitable projects for practical effectuation.

Anion Exchange Membranes for Fuel Cell Application: A Review

The fuel cell industry is the most promising industry in terms of the advancement of clean and safe technologies for sustainable energy generation. The polymer electrolyte membrane fuel cell is divided into two parts: anion exchange membrane fuel cells (AEMFCs) and proton exchange membrane fuel cells (PEMFCs). In the case of PEMFCs, high-power density was secured and research and development for commercialization have made significant progress. However, there are technical limitations and high-cost issues for the use of precious metal catalysts including Pt, the durability of catalysts, bipolar plates, and membranes, and the use of hydrogen to ensure system stability. On the contrary, AEMFCs have been used as low-platinum or non-platinum catalysts and have a low activation energy of oxygen reduction reaction, so many studies have been conducted to find alternatives to overcome the problems of PEMFCs in the last decade. At the core of ensuring the power density of AEMFCs is the anion exchange membrane (AEM) which is less durable and less conductive than the cation exchange membrane. AEMFCs are a promising technology that can solve the high-cost problem of PEMFCs that have reached technological saturation and overcome technical limitations. This review focuses on the various aspects of AEMs for AEMFCs application.