An alternative solvent system for the steady state electrospinning of polycaprolactone

Electrospun Ibuprofen-Loaded Blend PCL/PEO Fibers for Topical Drug Delivery Applications

Electrospun drug-eluting fibers have demonstrated potentials in topical drug delivery applications, where drug releases can be modulated by polymer fiber compositions. In this study, blend fibers of polycaprolactone (PCL) and polyethylene oxide (PEO) at various compositions were electrospun from 10 wt% of polymer solutions to encapsulate a model drug of ibuprofen (IBP). The results showed that the average polymer solution viscosities determined the electrospinning parameters and the resulting average fiber diameters. Increasing PEO contents in the blend PCL/PEO fibers decreased the average elastic moduli, the average tensile strength, and the average fracture strains, where IBP exhibited a plasticizing effect in the blend PCL/PEO fibers. Increasing PEO contents in the blend PCL/PEO fibers promoted the surface wettability of the fibers. The in vitro release of IBP suggested a transition from a gradual release to a fast release when increasing PEO contents in the blend PCL/PEO fibers up to 120 min. The in vitro viability of blend PCL/PEO fibers using MTT assays showed that the fibers were compatible with MEF-3T3 fibroblasts. In conclusion, our results explained the scientific correlations between the solution properties and the physicomechanical properties of electrospun fibers. These blend PCL/PEO fibers, having the ability to modulate IBP release, are suitable for topical drug delivery applications.

Cutaneous Pharmacokinetics of Topically Applied Novel Dermatological Formulations

Novel formulations are developed for dermatological applications to address a wide range of patient needs and therapeutic challenges. By pushing the limits of pharmaceutical technology, these formulations strive to provide safer, more effective, and patient-friendly solutions for dermatological concerns, ultimately improving the overall quality of dermatological care. The article explores the different types of novel dermatological formulations, including nanocarriers, transdermal patches, microsponges, and microneedles, and the techniques involved in the cutaneous pharmacokinetics of these innovative formulations. Furthermore, the significance of knowing cutaneous pharmacokinetics and the difficulties faced during pharmacokinetic assessment have been emphasized. The article examines all the methods employed for the pharmacokinetic evaluation of novel dermatological formulations. In addition to a concise overview of earlier techniques, discussions on novel methodologies, including tape stripping, in vitro permeation testing, cutaneous microdialysis, confocal Raman microscopy, and matrix-assisted laser desorption/ionization mass spectrometry have been conducted. Emerging technologies like the use of microfluidic devices for skin absorption studies and computational models for predicting drug pharmacokinetics have also been discussed. This article serves as a valuable resource for researchers, scientists, and pharmaceutical professionals determined to enhance the development and understanding of novel dermatological drug products and the complex dynamics of cutaneous pharmacokinetics.

The Manufacturing Conditions for the Direct and Reproducible Formation of Electrospun PCL/Gelatine 3D Structures for Tissue Regeneration

Electrospinning is a versatile technique for fabricating nanofibrous scaffolds for tissue engineering applications. However, the direct formation of 3D sponges through electrospinning has previously not been reproducible. We used a Taguchi experimental design approach to optimise the electrospinning parameters for forming PCL and PCL/gelatine 3D sponges. The following parameters were investigated to improve sponge formation: solution concentration, humidity, and solution conductivity. Pure PCL sponges were achievable. However, a much fluffier sponge formed by increasing the solution conductivity with gelatine. The optimal conditions for sponge formation 24 w/v% 80:20 PCL:gelatine on aluminium foil at ≥70% humidity, 15 cm, 22 kV and 1500 µL/h. The resulting sponge had a highly porous structure with a fibre diameter of ~1 µm. They also supported significantly higher cell viability than 2D electrospun mats, dropcast films of the same material and even the TCP positive control. Our study demonstrates that the direct formation of PCL/gelatine 3D sponges through electrospinning is feasible and promising for tissue engineering applications. The sponges have a highly porous structure and support cell viability, which are essential properties for tissue engineering scaffolds. Further studies are needed to optimise the manufacturing process and evaluate the sponges' long-term performance in vivo.

A Study of the Relationship between Polymer Solution Entanglement and Electrospun PCL Fiber Mechanics

Electrospun fibers range in size from nanometers to micrometers and have a multitude of potential applications that depend upon their morphology and mechanics. In this paper, we investigate the effect of polymer solution entanglement on the mechanical properties of individual electrospun polycaprolactone (PCL) fibers. Multiple concentrations of PCL, a biocompatible polymer, were dissolved in a minimum toxicity solvent composed of acetic acid and formic acid. The number of entanglements per polymer (ne) in solution was calculated using the polymer volume fraction, and the resultant electrospun fiber morphology and mechanics were measured. Consistent electrospinning of smooth fibers was achieved for solutions with ne ranging from 3.8 to 4.9, and the corresponding concentration of 13 g/dL to 17 g/dL PCL. The initial modulus of the resultant fibers did not depend upon polymer entanglement. However, the examination of fiber mechanics at higher strains, performed via lateral force atomic force microscopy (AFM), revealed differences among the fibers formed at various concentrations. Average fiber extensibility increased by 35% as the polymer entanglement number increased from a 3.8 ne solution to a 4.9 ne solution. All PCL fibers displayed strain-hardening behavior. On average, the stress increased with strain to the second power. Therefore, the larger extensibilities at higher ne also led to a more than double increase in fiber strength. Our results support the role of polymer entanglement in the mechanical properties of electrospun fiber at large strains.

Antibacterial Effect and Therapy of Chronic Skin Defects Using the Composite Bioscaffold Polycaprolactone/GelitaSpon/Povidone-Iodine in Domestic Dogs

Chronic wounds and the failure of conventional treatment are relatively common in veterinary medicine. Recently, there has been a growing interest in alternative therapeutic approaches and the utilization of biodegradable materials. Their potential application in wound therapy may offer a novel and more suitable option compared to conventional treatment methods. Biodegradable materials can be classified into two main categories: natural, synthetic, and a combination of both, which have the potential to have synergistically enhanced properties. In this study, four domestic dogs with clinical symptoms of chronic wounds were enrolled. These wounds underwent treatment utilizing a novel biodegradable composite material composed of gelatin sponge combined with two electrospun layers of polycaprolactone (PCL) along with polyvinylpyrrolidone (PVP) fibers containing povidone-iodine complex (PVP-I). The initial phase of the study was dedicated to evaluating the antibacterial properties of iodine against Staphylococcus aureus and Escherichia coli. On average, wound healing in domestic dogs took 22 days from the initial treatment, and iodine concentrations demonstrated a significant antibacterial effect against Escherichia coli and Staphylococcus aureus. Based on the favorable outcomes observed in wound management, we believe that the utilization of a blend of natural and synthetic biodegradable materials holds promise as an effective wound therapy option.

Polycaprolactone/Anthocyanin-Based Electrospun Volatile Amines Gas Indicator with Improved Visibility by Varying Bi-Solvent Ratio: A Case of Intelligent Packaging of Mackerel

Electrospun nanofibers have been applied as a new technology for gas indicators in food intelligent packaging. A poly(ε-caprolactone) (PCL)/red cabbage anthocyanin (RCA)-based nanofiber volatile amines gas indicator was developed by applying a bi-solvent of acetic acid (AA) and formic acid (FA) in electrospinning. The visibility of color change was improved from pink to blue, compared to blue to yellow-green, when using a single solvent of AA. The solutes of PCL (12.5, 15, 17.5, and 20%) and RCA (10, 20, 30, and 40%) and the solvents of AA/FA (9:1, 7:3, 5:5, 3:7, and 1:9) were applied in electrospinning under the condition of 12.5 cm, 1.0 mL/h, and 20 kV. The optimal microstructure with the thinnest fiber diameter and constant arrangement without forming NF beads appeared under the 7:3 FA/AA, 15% PCL, and 20% RCA condition. The indicator changed from pink to blue with the values of total color change (ΔE) of 10, 14, and 18 when exposed to the saturated gas of ammonia solutions of 8, 80, and 800 mM, respectively. The indicator was stable and unchanged in color for 28 days when exposed to light at room temperature. In the application to mackerel packaging, the built-in indicator changed from pink to purple regardless of storage temperature when the spoilage point was reached.

Biological properties of polycaprolactone and barium titanate composite in biomedical applications

The ceramic-polymer composite materials are widely known for their exceptional mechanical and biological properties. Polycaprolactone (PCL) is a biodegradable polymer material extensively used in various biomedical applications. At the same time, barium titanate (BT), a ceramic material, exhibits piezoelectric properties similar to bone, which is essential for osseointegration. Furthermore, a composite material that combines the benefits of PCL and BT results in an innovative composite material with enhanced properties for biomedical applications. Thus, this review is organised into three sections. Firstly, it aims to provide an overview of the current research on evaluating biological properties, including antibacterial activity, cytotoxicity and osseointegration, of PCL polymeric matrices in its pure form and reinforced structures with ceramics, polymers and natural extracts. The second section investigates the biological properties of BT, both in its pure form and in combination with other supporting materials. Finally, the third section provides a summary of the biological properties of the PCLBT composite material. Furthermore, the existing challenges of PCL, BT and their composites, along with future research directions, have been presented. Therefore, this review will provide a state-of-the-art understanding of the biological properties of PCL and BT composites as potential futuristic materials in biomedical applications.

Cell Guiding Multicomponent Nanoyarn Tendon Scaffolds with Tunable Morphology and Flexibility

Nanofibrous scaffolds are widely investigated for tendon tissue engineering due to their porous structure, high flexibility, and the ability to guide cells in a preferred direction. Previous research has shown that providing a microenvironment similar to in vivo settings improves tissue regeneration. Therefore, in this work, ingenious multicomponent nanoyarn scaffolds that mimic the fibrillar and tubular structures of tendons are developed for the first time through electrospinning and bundling nanoyarns followed by electrospinning of a nanofibrous shell around the bundle. Multicomponent nanoyarn scaffolds out of poly(ε-caprolactone) with varying porosity, density, and diameter were successfully produced by coelectrospinning with water-soluble poly(2-ethyl-2-oxazoline) as a sacrificial component. The diameter and fiber orientation of the nanoyarns were successfully tuned based on parameter-morphology models obtained by the design of experiments. Cyclic bending tests were performed, indicating that the flexibility of the multicomponent nanoyarn scaffolds depends on the morphology and can be tuned through controlling the number of nanoyarns in the bundle and the porosity. Indirect and direct cell culture tests using mouse and equine tendon cells revealed excellent cytocompatibility of the nanofibrous products and demonstrated the potential of the nanoyarns to guide the growing cells along the nanofiber direction, which is crucial for tendon tissue engineering.

Processing and characterization of aligned electrospun gelatin/polycaprolactone nanofiber mats incorporating borate glass (13-93B3) microparticles

Aligned biodegradable fibers incorporating bioactive glass particles are being highly investigated for tissue engineering applications. In this study, 5, 7 and 10 wt% melt-derived 1393B3 borate glass (BG) microparticles (average size: 3.15 µm) were incorporated in 83 wt% polycaprolactone (PCL) and 17 wt% gelatin (GEL) (83PCL/17GEL) solutions to produce aligned electrospun composite nanofiber mats. Addition of 5 wt% BG particles significantly increased the alignment of the nanofibers. However, further incorporation of BG particles led to reduced degree of alignment, likely due to an increase of viscosity. Mechanical tests indicated a tensile modulus and tensile strength of approximately 51 MPa and 3.4 MPa, respectively, for 5 wt% addition of 1393B3 BG microparticles, values considered suitable for soft tissue engineering applications. However, with the increasing amount of 1393B3 BG, the nanofiber mats became brittle. Contact angle was reduced after the addition of 5 wt% of 1393B3 BG particles from∼45° to∼39°. Cell culture studies with normal human dermal fibroblast (NHDF) cells indicated that 5 wt% 1393B3 BG incorporated nanofiber mats were cytocompatible whereas higher doping with 1393B3 BGs reduced biocompatibility. Overall, 5 wt% 1393B3 BG doped PCL/GEL nanofiber mats were aligned with high biocompatibility exhibiting desirable mechanical properties for soft tissue engineering, which indicates their potential for applications requiring aligned nanofibers, such as peripheral neural regeneration.

Osteoinductive Electrospun Scaffold Based on PCL-Col as a Regenerative Therapy for Peri-Implantitis

Peri-implantitis is a serious condition affecting dental implants that can lead to implant failure and loss of osteointegration if is not diagnosed and treated promptly. Therefore, the development of new materials and approaches to treat this condition is of great interest. In this study, we aimed to develop an electrospun scaffold composed of polycaprolactone (PCL) microfibers loaded with cholecalciferol (Col), which has been shown to promote bone tissue regeneration. The physical and chemical properties of the scaffold were characterized, and its ability to support the attachment and proliferation of MG-63 osteoblast-like cells was evaluated. Our results showed that the electrospun PCL-Col scaffold had a highly porous structure and good mechanical properties. The resulting scaffolds had an average fiber diameter of 2-9 μm and high elongation at break (near six-fold under dry conditions) and elasticity (Young modulus between 0.9 and 9 MPa under dry conditions). Furthermore, the Col-loaded scaffold was found to decrease cell proliferation when the Col content in the scaffolds increased. However, cytotoxicity analysis proved that the PCL scaffold on its own releases more lactate dehydrogenase into the medium than the scaffold containing Col at lower concentrations (PCL-Col A, PCL-Col B, and PCL-Col C). Additionally, the Col-loaded scaffold was shown to effectively promote the expression of alkaline phosphatase and additionally increase the calcium fixation in MG-63 cells. Our findings suggest that the electrospun membrane loaded with Col can potentially treat peri-implantitis by promoting bone formation. However, further studies are needed to assess the efficacy and safety of this membrane in vivo.

Microscale and Macroscale Deformation Behavior of Electrospun Polymeric Nanofiber Membranes Using In Situ SEM during Mechanical Testing

Electrospun nanofiber membranes show high potential in various application fields (e.g., filtration, catalysis, and sensing). Nevertheless, knowledge of the mechanical behavior, and more specifically, the deformation of nanofiber membranes is still limited today which can complicate the appliance of nanofiber membranes in applications where they are mechanically loaded. In this paper, we, therefore, analyzed the mechanical behavior of polymeric nanofiber membranes with different fiber orientations (random and aligned) extensively. Polyamide 6 was used as a representative reference polymer for proof-of-concept. Mechanical tests show that all membranes have a coherent deformation behavior at the macroscale up to the point of fracture. Large variations in stiffness, ultimate strength, and ultimate strain were observed between membranes with different fiber orientations (Random: E-mod: 370 ± 34 MP; UTS: 38.5 ± 6.0 MPa; εmax: 30.0 ± 2.8%; Parallel aligned: E-mod: 753 ± 11 MPa; UTS: 55.4 ± 0.8 MPa; εmax: 12.0 ± 0.1%; Perpendicular aligned: E-mod: 24.1 ± 3.7 MPa; UTS:/; εmax: >40%). This shows the versatility and tunability of the mechanical behavior of these nanofiber membranes. At the microscale, the fibrous structure results in deformation mechanisms that resist failure formation and progression when the membrane is mechanically loaded. This results in a high fracture resistance, even for pre-damaged membranes. Realignment of the fibers along the loading direction causes crack tip blunting, locally reinforcing the membrane.

Effect of PCL nanofiber mats coated with chitosan microcapsules containing cinnamon essential oil for wound healing

INTRODUCTION

Cinnamon is one of the most common spices that has been studied for its anti-inflammatory, antioxidant, and antibacterial properties in wound healing. The purpose of this study was to evaluate the effectiveness of polycaprolactone nanofiber mats coated with chitosan microcapsules loaded with cinnamon essential oil in wound healing.

MATERIAL AND METHODS

For this purpose, chitosan microcapsules containing cinnamon essential oil (µCS-CiZ) were prepared by ion gelation and PCL nanofibers by electrospinning. The size of the µCS-CiZ and the morphology of nanofibers were evaluated by DLS and FESEM methods. In order to evaluate wound healing, 48 rats in 4 groups of Control, µCS-CiZ, PCL, and PCL + µCS-CiZ and were examined on days 7, 14, and 21 in terms of macroscopy (wound closure rate) and histology (edema, inflammation, vascularity, fibrotic tissue, and re-epithelialization).

RESULTS

The particle size of the µCS-CiZ and the diameter of the nanofibers were estimated at about 6.33 ± 1.27 μm and 228 ± 33 nm, respectively. On day 21, both µCS-CiZ and PCL groups showed a significant decrease in wound size compared to the control group (P < 0.001). The PCL + µCS-CiZ group also showed a significant decrease compared to the µCS-CiZ (P < 0.05) and PCL groups (P < 0.05). Histological results showed further reduction of edema, inflammation, and vascularity in granulation tissue and appearance of moderate to marked fibrotic tissue in PCL + µCS-CiZ group compared with the other groups.

CONCLUSION

The results of the study showed that the combined use of PCL + µCS-CiZ indicates a synergistic effect on improving wound healing.

Solvent system effects on the physical and mechanical properties of electrospun Poly(ε-caprolactone) scaffolds for in vitro lung models

Mechanical properties are among the key considerations for the design and fabrication of complex tissue models and implants. In addition to the choice of material and the processing technique, the solvent system can significantly influence the mechanical properties of scaffolds. Poly(ε-caprolactone) (PCL) has been abundantly used to develop constructs, fibrous in particular, for pharmaceutical and biomedical research due to the flexibility offered by PCL-based fibrous matrices. The effect of solvent type on the morphological features of electrospun fibres has been extensively studied. Nevertheless, comprehensive studies on the impact of the solvent system on the mechanical properties of electrospun PCL fibres are lacking. This study elucidates the relationship between topographical, physical and mechanical properties of electrospun PCL fibrous meshes upon using various solvent systems. The results of the mechanical investigation highlight the significance of inter-fibre bonds on the mechanical properties of the bulk membranes and that the option of altering the solvent system composition could be considered for tuning the mechanical properties of the PCL scaffolds to serve specific biomedical application requirements. The applicability of the developed membranes as artificial ECM (Extracellular matrix) in the lung will then be investigated and compared to the commercial Polycarbonate (PC) membranes that are often used for in vitro lung models.

The solvent chosen for the manufacturing of electrospun polycaprolactone scaffolds influences cell behavior of lung cancer cells

The development of a trustworthy in vitro lung cancer model is essential to better understand the illness, find novel biomarkers, and establish new treatments. Polycaprolactone (PCL) electrospun nanofibers are a cost-effective and ECM-like approach for 3D cell culture. However, the solvent used to prepare the polymer solution has a significant impact on the fiber morphology and, consequently, on the cell behavior. Hence, the present study evaluated the effect of the solvent employed in the manufacturing on the physical properties of 15%-PCL electrospun scaffolds and consequently, on cell behavior of NCI-H1975 lung adenocarcinoma cells. Five solvents mixtures (acetic acid, acetic acid-formic acid (3:1, v/v), acetone, chloroform-ethanol (7:3, v/v), and chloroform-dichloromethane (7:3, v/v)) were tested. The highest cell viability ([Formula: see text] = 33.4%) was found for cells cultured on chloroform-ethanol (7:3) PCL scaffolds. Chloroform-dichloromethane (7:3) PCL scaffolds exhibited a roughness that enhanced the quality of electrospun filament, in terms of cell viability. Our findings highlighted the influence of the solvent on fiber morphology and protein adsorption capacity of nanofilaments. Consequently, these features directly affected cell attachment, morphology, and viability.

Electro Fluid Dynamics: A Route to Design Polymers and Composites for Biomedical and Bio-Sustainable Applications

In the last two decades, several processes have been explored for the development of micro and/or nanostructured substrates by sagely physically and/or chemically manipulating polymer materials. These processes have to be designed to overcome some of the limitations of the traditional ones in terms of feasibility, reproducibility, and sustainability. Herein, the primary aim of this work is to focus on the enormous potential of using a high voltage electric field to manipulate polymers from synthetic and/or natural sources for the fabrication of different devices based on elementary units, i.e., fibers or particles, with different characteristic sizes—from micro to nanoscale. Firstly, basic principles and working mechanisms will be introduced in order to correlate the effect of selected process parameters (i.e., an applied voltage) on the dimensional features of the structures. Secondly, a comprehensive overview of the recent trends and potential uses of these processes will be proposed for different biomedical and bio-sustainable application areas.

Nanostructured Electrospun Polycaprolactone-Propolis Mats Composed of Different Morphologies for Potential Use in Wound Healing

This study aimed to investigate different types of morphologies obtained using the electrospinning process to produce a material that enables wound healing while performing a controlled release. Using benign solvents, the authors prepared and characterised electrospun polycaprolactone mats loaded with propolis, a popular extract in traditional medicine with potential for skin repair. Different morphologies were obtained from distinct storage periods of the solution before electrospinning to investigate the effect of PCL hydrolysis (average diameters of fibres and beads: 159.2-280.5 nm and 1.9-5.6 μm, respectively). Phytochemical and FTIR analyses of the extract confirmed propolis composition. GPC and viscosity analyses showed a decrease in polymer molecular weight over the storage period (about a 70% reduction over 14 days) and confirmed that it was responsible for the nanostructure diversity. Moreover, propolis acted as a lubricant agent, affecting the spun solutions' viscosity and the thermal properties and hydrophilicity of the mats. All samples were within the value range of the water vapour transpiration rate of the commercial products (1263.08 to 2179.84 g/m²·day). Even though the presence of beads did not affect the propolis release pattern, an in vitro wound-healing assay showed that propolis-loaded mats composed of beaded fibres increased the cell migration process. Thus, these films could present the potential for use in wound dressing applications.

Repellent Activity of Clove Essential Oil Volatiles and Development of Nanofiber-Based Dispensers against Pear Psyllids (Hemiptera: Psyllidae)

Pear psyllids are the main vectors of the pathogen 'Candidatus Phytoplasma pyri' causing pear decline. Based on earlier reports, we tested the behavioral activity of the major synthetic compounds of clove essential oil (eugenol, eugenyl acetate, and β-caryophyllene) against Cacopsylla pyri and C. pyricola. Of six mixtures tested in olfactometer assays, a formulation consisting of three specific compounds (M6 mixture) demonstrated a repellent effect on both psyllid species. In addition, this formulation masked the odor of the host Pyrus communis cv. Williams Christ, disturbing the host finding ability of C. pyri. Electrospun fibers were produced with biocompatible polymers poly(ε-caprolactone), cellulose acetate, and solvents formic acid and acetic acid, loaded with the repellent mixture to test their efficacy as dispensers of repellents in laboratory and field. The fibers produced were repellent to C. pyri and effectively masked the odors of pear plants in olfactometer tests. In a pear orchard, we compared the captures of pear psyllids in green-colored attractive traps treated with nanofibers loaded with M6 mixture or unloaded nanofibers (blank). The result showed no differences in the captures of C. pyri between treatments. The release rates of volatiles from the fibers were evaluated weekly over 56 days. The fibers were able to entrap the major compound of the M6 mixture, eugenol, but the release rates were significantly reduced after 21 days. Our results suggest that biodegradable dispensers could be produced with electrospinning, but further improvements are necessary to use repellents as a management tool for pear psyllids in the field.

Polysaccharide-based nanofibers for pharmaceutical and biomedical applications: A review

Nanofibers are fibrous nanocarriers that can be synthesized from natural polymers, synthetic polymers, semiconducting materials, composite materials, and carbon-based materials. Recently, natural polysaccharides-based nanofibers are gaining attention in the field of pharmaceuticals and biomedical as these are biocompatible, biodegradable, non-toxic, and economic. Nanofibers can deliver a significant amount of drug to the targeted site and provide effective interaction of therapeutic agent at the site of action due to a larger surface area. Other important advantages of nanofibers are low density, high porosity, small pore size, high mechanical strength, and low cost. In this review, natural polysaccharides such as alginate, pullulan, hyaluronic acid, dextran, cellulose, chondroitin sulfate, chitosan, xanthan gum, and gellan gum are discussed for their characteristics, pharmaceutical utility, and biomedical applications. The authors have given particular emphasis to the several fabrication processes that utilize these polysaccharides to form nanofibers, and their recent updates in pharmaceutical applications such as drug delivery, tissue engineering, skin disorders, wound-healing dressings, cancer therapy, bioactive molecules delivery, anti-infectives, and solubility enhancement. Despite these many advantages, nanofibers have been explored less for their scale-up and applications in advanced therapeutic delivery.

Environmentally friendly fabrication of electrospun nanofibers made of polycaprolactone, chitosan and κ-carrageenan (PCL/CS/κ-C)

Electrospun fibers based on biodegradable polyanionic or polycationic biopolymers are highly beneficial for biomedical applications. In this work, electrospun nanofibers made from poly(epsilon caprolactone) (PCL), chitosan (CS) and κ-carrageenan (κ-C) were successfully fabricated using several mixtures of benign solvents containing formic acid (FA) and acetic acid (AA). The addition of κ-carrageenan improved the preparation procedure for the production of PCL/CS fibers by electrospinning. Moreover, a polymer mixture was selected to be stored at -20 °C for one month with the purpose to study the properties of the resulting fiber mat. The results indicated that fiber characteristics were not seriously compromised compared to the ones of those fabricated with the original solution, which represents an important reduction in produced waste. Thus, the interactions that occur between positively and negatively charged hydrophilic polysaccharides might induce higher stability to the linear aliphatic polyester in the polymer mixture. All fiber mats were morphologically, physico-chemically and mechanically characterized, showing average fiber diameters in the nano scale. A direct cell viability assay using ST-2 cells demonstrated cell proliferation after 7 days of incubation for all prepared fiber mats, confirming their suitability as potential candidates for bone tissue engineering and wound healing applications.

Effects of drug concentration and PLGA addition on the properties of electrospun ampicillin trihydrate-loaded PLA nanofibers

The aim of this study was to produce ampicillin trihydrate-loaded poly(lactic acid) (PLA) and PLA/poly(lactic-co-glycolic acid) (PLA/PLGA) polymeric nanofibers via electrospinning using 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) as the solvent for local application in tissue engineering. The effects of ampicillin trihydrate concentration (4-12%) and addition of PLGA (20-80%) on the spinnability of the solutions, morphology, average nanofiber diameter, encapsulation efficiency, drug release, and mechanical properties of PLA and PLA/PLGA nanofibers were examined. All nanofibers were bead-free and uniform. They had favorable encapsulation efficiency (approx. 90%) and mechanical properties. The increase in the amount of ampicillin trihydrate caused an increase in the diameter and burst effect of the nanofibers. The drug release ended on the 7th and 3rd day with nanofibers containing 4% and 12% of drug, respectively. The prolonged and controlled drug release for ten days was obtained with nanofibers containing 8% of drug. Thus, the ideal drug concentration was determined to be 8%. Nanofibers containing PLA/PLGA had a larger diameter than those including PLA. In addition, both the strength and elongation of nanofibers decreased depending on the increase in nanofiber size with the addition of PLGA, increased amount of drug, and ratios of PLGA. Drug release studies showed that PLA/PLGA nanofibers exhibited a lower burst effect and a decrease in drug release when compared to PLA nanofibers. Finally, PLA/PLGA nanofibers can be produced with enhanced encapsulation efficiency and mechanical properties, resulting in controlled and tailored release of ampicillin trihydrate for at least ten days. In conclusion, it was demonstrated that the addition of PLGA in different ratios and the amount of drug can be manipulated to obtain the desired properties (average nanofiber diameter, morphology, in vitro drug release, and mechanical properties) of PLA nanofibers.

In Vitro Biological Evaluation of a Fabricated Polycaprolactone/Pomegranate Electrospun Scaffold for Bone Regeneration

Different scaffold biomaterials are being investigated as a solution for bone loss due to disease or trauma. The aim of this study is the fabrication, characterization, and in vitro biological evaluation of a novel polycaprolactone (PCL) nanoscaffold incorporating pomegranate peel extract (PG) for bone regeneration. Using electrospinning, three groups of scaffolds were prepared: the control group PCL and two groups of PCL with PG concentrations (11 and 18 weight %). The antioxidant activity and the total phenolic content (TPC) of the fabricated nanoscaffolds were evaluated, in addition to the porosity and degradation measurement. Cultured osteoblasts derived from rabbit bone marrow mesenchymal stem cells were used for the assessment of cell proliferation and attachment on the scaffold's surface. Scaffolds' characterization showed uniform nanofibers (NFs) with a fiber diameter range of 149-168 nm. Meanwhile, higher antioxidant activity and TPC of the PG groups were detected. Furthermore, total porosities of 59 and 62% were determined for the PCL-PG scaffolds. An increased degradation rate and significant improvement in cell proliferation and cell attachment were revealed for the PCL-PG fabricated scaffolds. Such incorporation of natural food waste, PG, in PCL NFs offered novel PCL-PG scaffolds as a promising candidate for bone regeneration applications.

Skin-on-a-Chip Technology for Testing Transdermal Drug Delivery-Starting Points and Recent Developments

During the last decades, several technologies were developed for testing drug delivery through the dermal barrier. Investigation of drug penetration across the skin can be important in topical pharmaceutical formulations and also in cosmeto-science. The state-of- the-art in the field of skin diffusion measurements, different devices, and diffusion platforms used, are summarized in the introductory part of this review. Then the methodologies applied at Pázmány Péter Catholic University are shown in detail. The main testing platforms (Franz diffusion cells, skin-on-a-chip devices) and the major scientific projects (P-glycoprotein interaction in the skin; new skin equivalents for diffusion purposes) are also presented in one section. The main achievements of our research are briefly summarized: (1) new skin-on-a-chip microfluidic devices were validated as tools for drug penetration studies for the skin; (2) P-glycoprotein transport has an absorptive orientation in the skin; (3) skin samples cannot be used for transporter interaction studies after freezing and thawing; (4) penetration of hydrophilic model drugs is lower in aged than in young skin; (5) mechanical sensitization is needed for excised rodent and pig skins for drug absorption measurements. Our validated skin-on-a-chip platform is available for other research groups to use for testing and for utilizing it for different purposes.

Applying Acoustic Emission Technique for Detecting Various Damages Occurred in PCL Nanomodified Composite Laminates

Interleaving composite laminates by nanofibers is a well-known method of increasing interlaminar fracture toughness. Among many possibilities, polycaprolactone (PCL) nanofibers is one of the best choices for toughening composite laminates. The influence of PCL on delamination mode of failure is considered before. However, the effect of PCL on other damage modes, such as fiber breakage and matrix cracking, is yet to be studied. In this study, the acoustic emission (AE) technique is applied to determine the effect of toughening composite laminates by PCL nanofibers on matrix cracking, fiber/matrix debonding, and fiber breakage failure mechanisms. For this purpose, mode I and mode II fracture tests are conducted on modified and non-modified glass/epoxy laminates. Three different methods, i.e., peak frequency, wavelet transform, and sentry function, are utilized for analyzing the recorded AE data from mode I test. The results show that applying PCL nanofibers not only increases the mode I critical strain energy release rate by about 38%, but also decreases different failure mechanisms by between 75 and 94%.

Development and Evaluation of a Human Skin Equivalent in a Semiautomatic Microfluidic Diffusion Chamber

There is an increasing demand for transdermal transport measurements to optimize topical drug formulations and to achieve proper penetration profile of cosmetic ingredients. Reflecting ethical concerns the use of both human and animal tissues is becoming more restricted. Therefore, the focus of dermal research is shifting towards in vitro assays. In the current proof-of-concept study a three-layer skin equivalent using human HaCaT keratinocytes, an electrospun polycaprolactone mesh and a collagen-I gel was compared to human excised skin samples. We measured the permeability of the samples for 2% caffeine cream using a miniaturized dynamic diffusion cell (“skin-on-a-chip” microfluidic device). Caffeine delivery exhibits similar transport kinetics through the artificial skin and the human tissue: after a rapid rise, a long-lasting high concentration steady state develops. This is markedly distinct from the kinetics measured when using cell-free constructs, where a shorter release was observable. These results imply that both the established skin equivalent and the microfluidic diffusion chamber can serve as a suitable base for further development of more complex tissue substitutes.

Biodegradable polycaprolactone (PCL) based polymer and composites

Polycaprolactone (PCL) is a biodegradable polyester that has advantages over other biopolymers, making it an extensively researched polymer. PCL is a hydrophobic, slow-degrading, synthetic polymer making it particularly interesting for the preparation of long-term implantable devices and a variety of drug delivery systems. Recently, PCL has been used for additional applications including food packaging and tissue engineering. In this chapter, the processing methods and characterization of PCL will be discussed. The chapter will summarize the synthesis of poly(α-hydroxy acid) and the ring-opening polymerization of PCL. Discussion on the biodegradability of PCL will be reviewed. The biomedical applications of PCL, such as, drug-delivery systems, medical devices, and tissue engineering will be also summarized. Finally, the chapter will conclude with a characterization section outlining recent studies focusing on PCL based composites and films.

Alleviating the toxicity concerns of antibacterial cinnamon-polycaprolactone biomaterials for healthcare-related biomedical applications

Fibrous constructs with incorporated cinnamon-extract have previously been shown to have potent antifungal abilities. The question remains to whether these constructs are useful in the prevention of bacterial infections in fiber form and what the antimicrobial effects means in terms of toxicity to the native physiological cells. In this work, cinnamon extract containing poly (ε-caprolactone) (PCL) fibers were successfully manufactured by pressurized gyration and had an average size of ∼2 μm. Cinnamon extract containing PCL fibers were tested against Escherichia coli, Staphylococcus aureus, Methicillin resistant staphylococcus aureus, and Enterococcus faecalis bacterial species to assess their antibacterial capacity; it was found that these fibers were able to reduce viable cell numbers of the bacterial species up to two orders of magnitude lower than the control group. The results of the antibacterial tests were assessed by scanning electron microscopy (SEM). The constructs were also tested under indirect MTT tests where they showed little to no toxicity, similar to the control groups. Additionally, cell viability fluorescent imaging displayed no significant toxicity issues with the fibers, even at their highest tested concentration. Here we present a viable method for the production the non-toxic and naturally abundant cinnamon extracted fibers for numerous biomedical applications.

Development of biodegradable webs of PLA/PCL blends prepared via electrospinning: Morphological, chemical, and thermal characterization

Biodegradable polymers have a mean role to mimic native tissues and allow cells to penetrate, grow, and proliferate with their advanced features in tissue engineering applications. The physiological, chemical, mechanical, and biological qualities of the surfaces, which are presented from biodegradable polymers, affect the final properties of the scaffolds. In this study, it is aimed to produce fibrous webs by electrospinning method for tissue engineering applications using two different biopolymers, polylactic acid (PLA) and polycaprolactone (PCL). These polymers are used either alone or in a blended form (PLA/PCL, 1/1 wt.). Within the scope of the study, polymer concentrations (6, 8 and 10%) and solvent types (used for chloroform/ethanol/acetic acid mixture, PCL and PLA/PCL mixtures, and chloroform/acetone, PLA) vary as solution parameters. Fibrous webs are investigated in terms of morphological, chemical, and thermal characteristics. Results show continuous fibers are examined for 8 or 10% polymer concentrations with an average fiber diameter of 1.3-2.7 μm and pore area of 4-9 μm² . No fiber formation is observed in sample groups with a polymer concentration of 6% and beaded structures are formed. Water contact angle analysis proves the hydrophobic properties of PLA and PCL, whereas Fourier-transform infrared results show there is no solution residue on the surfaces, so there is no toxic effect. Also, in differential scanning calorimetry analysis, the characteristic crystallization peaks of the polymers are recognized, and when the polymers are in a blend, it beholds that they have effects on each other's crystallization.

Step-by-step design of poly (ε-caprolactone) /chitosan/Melilotus officinalis extract electrospun nanofibers for wound dressing applications

Composition of polymers and choosing the type of solvents in electrospinning systems is of great importance to achieve a mat with optimal properties. In this work, with emphasizing the influence of a novel solvent system, an electrospun wound dressing was designed in four steps. Firstly, to study the effect of polymer-solvent interactions and electrospinning distance, a constant amount of polycaprolactone (PCL) was dissolved at different compositions of formic acid (FA)/dichloromethane (DCM) and was electrospun at different distances. The composition of 80FA/20DCM and distance of 15 cm were selected as optimal conditions by lowest average diameter of fibers and simultaneously good surface uniformity. In the second step, the concentration of PCL was considered variable to achieve the lowest diameter of fibers. Finally, in the third and fourth steps, different concentrations of chitosan (CN) and constant dosage of Melilotus officinalis (MO) extract were added to the solution. The extract contained fibers had a mean diameter of 275 ± 41 nm which is in the required condition for wound caring. Eventually, the optimized PCL/CN and PCL/CN/MO specimens were evaluated by FTIR, DSC, Tensile, water contact angle, antibacterial assays, cell viability, and drug release analysis for determining their function and properties.

Curdlan-Chitosan Electrospun Fibers as Potential Scaffolds for Bone Regeneration

Polysaccharides have received a lot of attention in biomedical research for their high potential as scaffolds owing to their unique biological properties. Fibrillar scaffolds made of chitosan demonstrated high promise in tissue engineering, especially for skin. As far as bone regeneration is concerned, curdlan (1,3-β-glucan) is particularly interesting as it enhances bone growth by helping mesenchymal stem cell adhesion, by favoring their differentiation into osteoblasts and by limiting the osteoclastic activity. Therefore, we aim to combine both chitosan and curdlan polysaccharides in a new scaffold for bone regeneration. For that purpose, curdlan was electrospun as a blend with chitosan into a fibrillar scaffold. We show that this novel scaffold is biodegradable (8% at two weeks), exhibits a good swelling behavior (350%) and is non-cytotoxic in vitro. In addition, the benefit of incorporating curdlan in the scaffold was demonstrated in a scratch assay that evidences the ability of curdlan to express its immunomodulatory properties by enhancing cell migration. Thus, these innovative electrospun curdlan–chitosan scaffolds show great potential for bone tissue engineering.

In-vitro Characterization of a Hernia Mesh Featuring a Nanostructured Coating

Abdominal hernia repair is a frequently performed surgical procedure worldwide. Currently, the use of polypropylene (PP) surgical meshes for the repair of abdominal hernias constitutes the primary surgical approach, being widely accepted as superior to primary suture repair. Surgical meshes act as a reinforcement for the weakened or damaged tissues and support tissue restoration. However, implanted meshes could suffer from poor integration with the surrounding tissues. In this context, the present study describes the preliminary evaluation of a PCL-Gel-based nanofibrous coating as an element to develop a multicomponent hernia mesh device (meshPCL-Gel) that could overcome this limitation thanks to the presence of a nanostructured biomimetic substrate for enhanced cell attachment and new tissue formation. Through the electrospinning technique, a commercial PP hernia mesh was coated with a nanofibrous membrane from a polycaprolactone (PCL) and gelatin (Gel) blend (PCL-Gel). Resulting PCL-Gel nanofibers were homogeneous and defect-free, with an average diameter of 0.15 ± 0.04 μm. The presence of Gel decreased PCL hydrophobicity, so that membranes average water contact angle dropped from 138.9 ± 1.1° (PCL) to 99.9 ± 21.6°, while it slightly influenced mechanical properties, which remained comparable to those of PCL (E = 15.7 ± 2.7 MPa, σ R = 7.7 ± 0.6 ε R = 118.8 ± 13.2%). Hydrolytic and enzymatic degradation was conducted on PCL-Gel up to 28 days, with maximum weight losses around 20 and 40%, respectively. The meshPCL-Gel device was obtained with few simple steps, with no influences on the original mechanical properties of the bare mesh, and good stability under physiological conditions. The biocompatibility of meshPCL-Gel was assessed by culturing BJ human fibroblasts on the device, up to 7 days. After 24 h, cells adhered to the nanofibrous substrate, and after 72 h their metabolic activity was about 70% with respect to control cells. The absence of detectable lactate dehydrogenase in the culture medium indicated that no necrosis induction occurred. Hence, the developed nanostructured coating provided the meshPCL-Gel device with chemical and topographical cues similar to the native extracellular matrix ones, that could be exploited for enhancing the biological response and, consequently, mesh integration, in abdominal wall hernia repair.

A New Generation of Electrospun Fibers Containing Bioactive Glass Particles for Wound Healing

Chitosan fibers blended with polyethylene oxide (CHIT_PEO) and crosslinked with genipin were fabricated by electrospinning technique. Subsequently, CHIT_PEO bioactive glass composite electrospun mats were fabricated with the aim to achieve flexible structures with adequate mechanical properties and improved biological performance respect to CHIT_PEO fibers, for potential applications in wound healing. Three different compositions of bioactive glasses (BG) were selected and investigated: 45S5 BG, a Sr and Mg containing bioactive glass (BGMS10) and a Zn-containing bioactive glass (BGMS_2Zn). Particulate BGs (particles size < 20 μm) were separately added to the starting CHIT_PEO solution before electrospinning. The two recently developed bioactive glasses (BGMS10 and BGMS_2Zn) showed very promising biological properties in terms of bioactivity and cellular viability; thus, such compositions were added for the first time to CHIT_PEO solution to fabricate composite electrospun mats. The incorporation of bioactive glass particles and their distribution into CHIT_PEO fibers were assessed by SEM and FTIR analyses. Furthermore, CHIT_PEO composite electrospun mats showed improved mechanical properties in terms of Young’s Modulus compared to neat CHIT_PEO fibers; on the contrary, the values of tensile strain at break (%) were comparable. Biological performance in terms of cellular viability was investigated by means of WST-8 assay and CHIT_PEO composite electrospun mats showed cytocompatibility and the desired cellular viability.

The impact of relative humidity on electrospun polymer fibers: From structural changes to fiber morphology

Electrospinning is one of the most important methods used for the production of nanostructured materials. Electrospun nanofibers are used in a wide spectrum of applications such as drug delivery systems, filtration, fog harvesting, tissue engineering, smart textiles, flexible electronics, and more. Control of the manufacturing process is essential for further technology developments. In electrospinning, relative humidity is a crucial parameter that influences nearly all the properties of the collected fibers, such as morphology, mechanical properties, liquid retention, wetting properties, phase composition, chain conformation, and surface potential. Relative humidity is a determining component of a reliable process as it governs charge dissipation and solvent evaporation. This review summarizes the electrospinning process and its applications, phase separation processes, and impact of relative humidity on the properties of polymer fibers. We investigated relative humidity effects on both hydrophilic and hydrophobic polymers using over 20 polymers and hundreds of solvent systems. Most importantly, we underlined the indisputable importance of relative humidity in process repeatability and demonstrated its impact on almost all aspects of fiber production from a solution droplet to an electrospun network.

Electrospun PCL Fiber Mats Incorporating Multi-Targeted B and Co Co-Doped Bioactive Glass Nanoparticles for Angiogenesis

Vascularization is necessary in tissue engineering to keep adequate blood supply in order to maintain the survival and growth of new tissue. The synergy of biologically active ions with multi-target activity may lead to superior angiogenesis promotion in comparison to single-target approaches but it has been rarely investigated. In this study, polycaprolactone (PCL) fiber mats embedded with B and Co co-doped bioactive glass nanoparticles (BCo.BGNs) were fabricated as a tissue regeneration scaffold designed for promoting angiogenesis. BCo.NBGs were successfully prepared with well-defined spherical shape using a sol-gel method. The PCL fiber mats embedding co-doped bioactive glass nanoparticles were fabricated by electrospinning using benign solvents. The Young’s moduli of the nanoparticle containing PCL fiber mats were similar to those of the neat fiber mats and suitable for scaffolds utilized in soft tissue repair approaches. The mats also showed non-cytotoxicity to ST-2 cells. PCL fiber mats containing BCo.BGNs with a relatively high content of B and Co promoted the secretion of vascular endothelial growth factor to a greater extent than PCL fiber mats with a relatively low B and Co contents, which demonstrates the potential of dual ion release (B and Co) from bioactive glasses to enhance angiogenesis in soft tissue engineering.

Incorporation of Bioactive Glasses Containing Mg, Sr, and Zn in Electrospun PCL Fibers by Using Benign Solvents

Poly(ε-caprolactone) (PCL) and PCL/bioactive glass composite fiber mats were produced by electrospinning technique. To improve cell adhesion and proliferation (i) 45S5, (ii) a bioactive glass containing strontium and magnesium oxides, and (iii) a bioactive glass containing zinc oxide were separately added to the starting PCL solution before electrospinning. A good incorporation of bioactive glass particles in PCL electrospun mats was confirmed by SEM and FTIR analyses. Bioactivity was evaluated by immersion of PCL mats and PCL/bioactive glass electrospun fiber mats in simulated body fluid (SBF). Bone murine stromal cells (ST-2) were employed in WST-8 assay to assess cell viability, cell morphology, and proliferation. The results showed that the presence of bioactive glass particles in the fibers enhances cell adhesion and proliferation compared to neat PCL mats. Furthermore, PCL/bioactive glass electrospun mats showed higher wound-healing rate (measured as cell migration rate) in vitro compared to neat PCL electrospun mats. Therefore, the characteristics of the PCL matrix combined with biological properties of bioactive glasses make PCL/bioactive glass composite ideal candidate for biomedical application.

Ultrathin single and multiple layer electrospun fibrous membranes of polycaprolactone and polysaccharides

Electrospinning was used to produce fibrous membranes, in single and multiple layers, from poly(ε-caprolactone), pullulan, and from mixtures of poly(ε-caprolactone) with potato modified starch and β-glucan. It was possible to obtain single-layer membranes from solutions of pullulan in water, poly(ε-caprolactone) in chloroform, and from mixtures of poly(ε-caprolactone)/β-glucan and poly(ε-caprolactone)/potato modified starch in chloroform. Scanning electron microscopy images showed the formation of ultrathin homogeneous fibers from electrospun poly(ε-caprolactone) and pullulan, whereas the fibers obtained from mixtures of poly(ε-caprolactone)/ β -glucan and poly(ε-caprolactone)/potato modified starch had different sizes and morphologies, as well as irregular microstructures, characterized by the presence of beads. Contact angle analyses showed that pullulan membranes were extremely hydrophilic, while poly(ε-caprolactone) membranes were predominantly hydrophobic. Subsequently, poly(ε-caprolactone)-pullulan-poly(ε-caprolactone) multilayer membranes, with intermediate wettability, were prepared by successive electrospinning steps. Infrared spectroscopy and calorimetric analyses showed the presence of both polymers and the absence of changes in their structure and stability due to electrospinning, indicating adequate compatibility between the two polymers. We foresee that the polyester-polysaccharide multilayer membrane might be used as a biodegradable vehicle for active agents with different hydrophobicity, with applications as food packaging and biocompatible scaffold materials.

Effects of Fiber Density and Strain Rate on the Mechanical Properties of Electrospun Polycaprolactone Nanofiber Mats

This study examines the effects of electrospun polycaprolactone (PCL) fiber density and strain rate on nanofiber mat mechanical properties. An automated track collection system was employed to control fiber number per mat and promote uniform individual fiber properties regardless of the duration of collection. Fiber density is correlated to the mechanical properties of the nanofiber mats. Young's modulus was reduced as fiber density increased, from 14,901 MPa for samples electrospun for 30 s (717 fibers +/- 345) to 3,615 MPa for samples electrospun for 40 min (8,310 fibers +/- 1,904). Ultimate tensile strength (UTS) increased with increasing fiber density, where samples electrospun for 30 s resulted in a UTS of 594 MPa while samples electrospun for 40 min demonstrated a UTS of 1,250 MPa. An average toughness of 0.239 GJ/m3 was seen in the 30 s group, whereas a toughness of 0.515 GJ/m3 was observed at 40 min. The ultimate tensile strain for samples electrospun for 30 s was observed to be 0.39 and 0.48 for samples electrospun for 40 min. The relationships between UTS, Young's modulus, toughness, and ultimate tensile strain with increasing fiber density are the result of fiber-fiber interactions which leads to network mesh interactions.

Production of a novel poly(ɛ-caprolactone)-methylcellulose electrospun wound dressing by incorporating bioactive glass and Manuka honey

Wound dressings produced by electrospinning exhibit a fibrous structure close to the one of the extracellular matrix of the skin. In this article, electrospinning was used to fabricate fiber mats based on the well-known biopolymers poly(ɛ-caprolactone) (PCL) and methylcellulose (MC) using benign solvents. The blend fiber mats were cross-linked using Manuka honey and additionally used as a biodegradable platform to deliver bioactive glass particles. It was hypothesized that a dual therapeutic effect can be achieved by combining Manuka honey and bioactive glass. Morphological and chemical examinations confirmed the successful production of submicrometric PCL-MC fiber mats containing Manuka honey and bioactive glass particles. The multifunctional fiber mats exhibited improved wettability and suitable mechanical properties (ultimate tensile strength of 3-5 MPa). By performing dissolution tests using simulated body fluid, the improved bioactivity of the fiber mats by the addition of bioactive glass was confirmed. Additionally, cell biology tests using human dermal fibroblasts and human keratinocytes-like HaCaT cells showed the potential of the fabricated composite fiber mats to be used as wound dressing, specially due to the ability to support wound closure influenced by the presence of bioactive glass. Moreover, based on the results of the antibacterial tests, it is apparent that an optimization of the electrospun fiber mats is required to develop suitable wound dressing for the treatment of infected wounds.

Multilayer Alginate-Polycaprolactone Electrospun Membranes as Skin Wound Patches with Drug Delivery Abilities

A multilayer nanofibrous membrane consisting of a layer of polycaprolactone and one of physically cross-linked alginate-embedding ZnO nanoparticles is prepared via electrospinning technique as potential wound healing patches with drug delivery capabilities. A washing-cross-linking protocol is developed to obtain stable materials at the same time removing poly(ethylene oxide), which was used here as a cospinning agent for alginate, without interfering with the membrane's peculiar nanofibrous structure. The mechanical behavior of the samples is assessed via a uniaxial tensile test showing appropriate resistance and manageability together with a good thermal stability as proved via thermogravimetric analysis. The polycaprolactone external layer enriches the samples with good liquid-repellent properties, whereas the alginate layer is able to promote tissue regeneration owing to its capability to promote cell viability and allow exudate removal and gas exchanges. Moreover, using methylene blue and methyl orange as model molecules, promising drug delivery abilities are observed for the mats. Indeed, depending on the nature and on the dye-loading concentration, the release kinetic can be easily tuned to obtain a slow controlled or a fast burst release. Consequently, the proposed alginate-polycaprolactone membrane represents a promising class of innovative, simple, and cost-effective wound healing patches appropriate for large-scale production.

Electrospun Nano-Fibers for Biomedical and Tissue Engineering Applications: A Comprehensive Review

Pharmaceutical nano-fibers have attracted widespread attention from researchers for reasons such as adaptability of the electro-spinning process and ease of production. As a flexible method for fabricating nano-fibers, electro-spinning is extensively used. An electro-spinning unit is composed of a pump or syringe, a high voltage current supplier, a metal plate collector and a spinneret. Optimization of the attained nano-fibers is undertaken through manipulation of the variables of the process and formulation, including concentration, viscosity, molecular mass, and physical phenomenon, as well as the environmental parameters including temperature and humidity. The nano-fibers achieved by electro-spinning can be utilized for drug loading. The mixing of two or more medicines can be performed via electro-spinning. Facilitation or inhibition of the burst release of a drug can be achieved by the use of the electro-spinning approach. This potential is anticipated to facilitate progression in applications of drug release modification and tissue engineering (TE). The present review aims to focus on electro-spinning, optimization parameters, pharmacological applications, biological characteristics, and in vivo analyses of the electro-spun nano-fibers. Furthermore, current developments and upcoming investigation directions are outlined for the advancement of electro-spun nano-fibers for TE. Moreover, the possible applications, complications and future developments of these nano-fibers are summarized in detail.

Electrospinning of linezolid loaded PLGA nanofibers: effect of solvents on its spinnability, drug delivery, mechanical properties, and antibacterial activities

Objective: The choice of a desirable solvent/solvent system is fundamental for optimization of electrospinning by altering the rheological and electrostatic properties of the polymer solutions.Methods: The effects of the solvents and their properties on the viscosity and spinnability of the polymer solutions and the diameter, morphology, in vitro drug release, drug release mechanisms, antibacterial activity against methicillin-resistant Staphylococcus aureus (MRSA) and mechanical properties of electrospun poly-(d,l-lactide-co-glycolide) (PLGA) nanofibers were investigated. Dichloromethane (DCM), dimethylformamide (DMF), various ratios of DCM:DMF, and 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) were used as solvents.Results: Although solutions containing DCM/DMF alone were not spinnable, different ratios of DCM:DMF and HFIP were determined as suitable solvents to produce nanofibers because of high enough conductivity, viscosity, and low enough surface tension of the solutions. The DCM:DMF ratio was highly effective on viscosity, nanofiber diameter, morphology, and linezolid release rate. The viscosity of HFIP containing solution was higher and the obtained nanofibers were thicker and smoother with better mechanical properties. The release of nanofibers containing HFIP at a concentration of 10% w/v PLGA was more prolonged than nanofibers containing DCM:DMF mixture. The effect of linezolid content on nanofibers was also investigated. As the amount of linezolid increased, nanofiber diameter and drug release increased and bead formation was observed. While antibacterial activity with nanofibers for which DCM:DMF was used, lasted for 13 days, it was extended to 16 days in nanofibers for which HFIP was used.Conclusions: Type and ratio of the solvent system affected viscosity and spinnability of the solutions, the average nanofiber diameter, morphology, in vitro activity and mechanical properties of the obtained electrospun nanofibers.

Effects of an Acetic Acid and Acetone Mixture on the Characteristics and Scaffold–Cell Interaction of Electrospun Polycaprolactone Membranes

Green electrospinning has attracted great interest since non-toxic solvents were shown to be applicable in the fabrication of fibrous materials while ensuring health safety and environmental protection. Less harmful reagents such as acetone (AC) and acetic acid (AA) have been employed in this field in recent years. However, research in this area is still rare, yielding only preliminary results. In this study, two different types of solvents (pure AC and an AA/AC mixture) were used to fabricate electrospun polycaprolactone (PCL) membranes. Sample morphology, wettability, tensile strength, and chemical composition were compared between two types of membranes. Cell–scaffold interaction was also examined by cell adhesion and proliferation assays. The results demonstrate that the two types of solvents had significant effects on membrane morphology, physical strength, and cell adherence behaviors, which should be considered for different application purposes.