A SiO2@MIP electrochemical sensor based on MWCNTs and AuNPs for highly sensitive and selective recognition and detection of dibutyl phthalate

Advances in electrochemical sensors for naproxen detection: Mechanisms, performance factors, and emerging challenges

Naproxen (NAP), a nonsteroidal anti-inflammatory, analgesic, and antipyretic drug, has fewer side effects than similar drugs due to its aryl acetic acid structure. For this reason, it is widely prescribed to manage fever, short-term and long-term pain, and musculoskeletal disorders. However, its use has complications such as changes in kidney function, severe gastrointestinal lesions, and increased bleeding after surgery. In addition, the toxicity of NAP or its metabolites affects the organisms in the ecosystem. Therefore, it is necessary to determine the pharmaceutical quality of produced NAP and measure its amount in living organisms and the environment. Spectroscopy, chromatography, and electrochemical methods have been used to determine NAP. Electrochemical methods have attracted more attention due to their low cost, easy sample preparation, availability, sensitivity, and acceptable results. In addition, using nanomaterials for NAP oxidation results in high surface-to-volume, high available active sites, low cost, and long-term usability with high sensitivity. In this review, electrochemical-based methods for NAP analysis and sensing have been reviewed. Also, the influential factors in NAP identification and evaluation, and their oxidation mechanism have been discussed.

Preparation of a V-COF@SWCNTs-COOH/SPCE supported molecularly imprinted electrochemical sensor for real-time detection of trace sulfadimidine

To overcome the limitations of insufficient sensitivity and poor specificity of portable screen-printed carbon electrode-electrochemical sensors (SPCE-EC) in practical applications, we prepared carrier composites of carboxylic single-walled carbon nanotubes vertically grafted by covalent organic frameworks (v-COF@SWCNTs-COOH) and coated with a molecularly imprinted polymer (MIP) of sulfadimidine (SM2). 55 °C hot steam elution is more eco-friendly than traditional organic solvent elution. The results showed that when the mass ratio of DBA to DBA-SWCNTs was 1:1, the v-COF@SWCNTs-COOH obtained by the two-step synthesis method could increase the electrical signal up to 2.33-fold of the bare electrode. The bifunctional monomer MIP prepared on the above structure enhanced the signal response by 2.91-fold, with a high imprint factor of 20. The assembled MIP/v-COF@SWCNTs-COOH/SPCE were analyzed by differential pulse voltammetry (DPV) with a high sensitivity of 0.21 nM for LOD and 0.70 nM for LOQ. In milk and fish samples, the recovery rate was 95.0 %-104.8 %. The validation of authentic pork samples with the statutory LC-MS/MS method showed no significant difference (P > 0.05). The sensor's performance indicators remained robust after five repeated uses. Therefore, the MIP/v-COF@SWCNTs-COOH/SPCE combines the cheapness and portability of SPCE, while the sensitivity and specificity of small molecule detection were significantly improved.

Utilizing electrospun molecularly imprinted membranes for food industry: Opportunities and challenges

Molecularly imprinted polymers (MIPs) have been widely studied in environmental protection and food industry, owing to their excellent specific recognition and structural stability. However, MIPs prepared by conventional methods suffer from low adsorption capacity and slow mass transfer rate. To date, the combination of electrostatic spinning technology and molecular imprinting technology has been proposed to prepare molecularly imprinted membranes (MIMs) with specific recognition capability, and has shown great attraction in the separation and detection of food additives, as well as the extraction and release of active ingredients. In recent years, MIPs and electrostatic spinning technologies have been investigated and evaluated. However, there is no review of electrostatically spun MIMs for food field. In this review, we focus on the fabrication methods and applications of electrostatically spun MIMs in the food, discuss the challenges in practical food applications, and emphasize the promising applications of electrostatically spun MIMs in food field.

A water compatible magnetic molecularly imprinted nanocomposite for the class-selective enrichment of quinoxaline-1,4-dioxides in environmental water

In this work, a novel water compatible core-shell magnetic molecularly imprinted nanocomposite (Fe3O4-COOH@MIPs) was synthesized in an acetonitrile-water reaction system by adopting carboxyl group-functionalized Fe3O4 nanoparticles as the magnetic core, olaquindox as the template molecule and acrylamide as the functional monomer. The resulting Fe3O4-COOH@MIPs was characterized and applied as an adsorbent for magnetic solid-phase extraction (MSPE) of three quinoline-1,4-dioxides (QdNOs). The Fe3O4-COOH@MIPs possessed strong magnetic responsiveness, fast adsorption equilibrium rate (equilibrium within 5 min) and excellent selectivity. By coupling Fe3O4-COOH@MIPs based MSPE with high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS), good linearity (R2 ≥ 0.9985) and low limits of detection (0.83-5.0 ng L-1) for QdNOs were obtained. Finally, the proposed method was applied to determine trace QdNOs in environmental water samples, and the recoveries were in the range of 68.08-99.88% with RSD less than 12.5%.

Carbon nanomaterials as electrochemical sensors for theophylline: a review

Theophylline (TP) is a methylxanthine derivative, which serves as a valuable compound in treating respiratory disorders and acts as a bronchodilator agent. However, TP has a limited therapeutic range (20-100 μmol L-1), demanding precise monitoring to prevent potential drug toxicity even with slight level fluctuations during treatment. Thus, to overcome this limitation, electrochemical methods have been extensively used due to their efficacy in achieving sensitivity, selectivity, and accuracy. In the context of electrochemical sensors, nanocarbon-based materials have gained widespread recognition for their extensive applications. Therefore, this review aims to explore the latest advancements in carbon-based electrodes particularly used for the precise determination of TP through electrochemical methods. The results are expected to provide insights into the profound significance of the methods in enhancing the accuracy and sensitivity for the detection of TP.

Stable detection of diazinon residues in vegetables by an electrochemiluminescent aptasensor based on the in-situ production of H2O2 from dual-catalytic glucose

Stable detection of diazinon (DZN) residues in vegetables is important for food safety. In this work, an electrochemiluminescence (ECL) aptasensor with dual-catalytic glucose in-situ production of H2O2 was constructed for the stable detection of DZN in vegetables. Firstly, MWCNTs@MB was prepared using π-π stacking interactions between methylene blue (MB) and multi-walled carbon nanotubes (MWCNTs) to enhance the loading of MB on an electrode and thus catalyze the generation of H2O2 from glucose. Secondly, Cu2O@AuNPs was formed by loading AuNPs on the surface of Cu2O through spontaneous reduction reaction, which improved the interfacial charge transfer, Cu2O nano-enzyme had glucose oxidase mimicking activity and could further catalyze the production of more H2O2 from glucose. MWCNTs@MB and Cu2O@AuNPs played a key role in the in-situ generation of co-reacting reagent H2O2, which solved the problem of unstable detection caused by the easy decomposition of the H2O2 solution added to the luminescence system. In addition, the aptamer was immobilized on the electrode surface by forming Au-S bonds with Cu2O@AuNPs. As a result, the ECL aptasensor performed good linearity in 1.00 pg mL-1-1.00 μg mL-1 and a low limit of detection (LOD) to 0.39 pg mL-1 (S/N = 3). This work provided an effective method for the accurate and stable detection of DZN residues in vegetables, which was of great significance in ensuring food safety and assessing the environmental risk of DZN.

Functionalized nano cellulose double-template imprinted aerogel microsphere for the targeted enrichment of taxanes

Paclitaxel, a diterpenoid isolated from the bark of Taxus wallichiana var. chinensis (Pilger) Florin, is currently showing significant therapeutic effects against a variety of cancers. Baccatin III (Bac) and 10-Deacetylbaccatin III (10-DAB) are in great demand as important precursors for the synthesis of paclitaxel. This work aims to develop a simple, rapid and highly selective, safe, and non-polluting molecularly imprinted material for 10-DAB and Bac enrichment. In this study, we innovatively prepared molecularly imprinted materials with nanocellulose aerogel microspheres and 2-vinylpyridine (2-VP) as a bifunctional monomer, and 10-DAB and Bac as bis-template molecules. In particular, functionalized nanocellulose dual-template molecularly imprinted aerogel microsphere (FNCAG-DMIM) were successfully synthesized by the bifunctional introduction of functional nanocellulose aerogel microsphere (FNCAG) modified with Polyethyleneimine (PEI) as a carrier and functional monomer, which provided a large number of recognition sites for bimodal molecules. FNCAG-DMIM showed high specificity for 10-DAB and Bac specific assays. Under the optimal experimental conditions, the adsorption capacities of FNCAG-DMIM for 10-DAB and Bac reached 52.27 mg g-1 and 53.81 mg g-1, respectively. In addition, it showed good reliability and practicality in the determination of real samples. The present study extends the research on the synthesis of natural functional monomers by molecularly imprinted materials and opens up new horizons for the targeted isolation of plant compounds by dual-template molecularly imprinted materials.

Ultrasensitive detection strategy for CAP by molecularity imprinted SERS sensor based on multiple synergistic enhancement of SiO2@AuAg with MOFs@Au signal carrier

Chloramphenicol (CAP) residue in food can cause great harm to human health, it is important to develop a rapid and sensitive method to detect CAP. Here, molecularly imprinted polymer (MIP) was combined with metal-organic frameworks@Au (MOFs@Au) collaborative construction surface-enhanced Raman spectroscopy (SERS) based aptasensor for CAP ultrasensitive detection. MOFs@Au first carried the Raman signal molecule toluidine blue (TB) and aptamer to form MOFs@Au@TB@Apt. In addition, rMIP (CAP was removed) was dropped onto the uniform three-dimensional (3D) SERS substrate SiO2@AuAg to form SiO2@AuAg@rMIP. In the presence of target CAP, it could be specifically captured with rMIP by covalent interaction and was recognised by the aptamer. During this time, SiO2@AuAg@rMIP@CAP could selectively connect MOFs@Au@TB@Apt to realise synergistic enhance the Raman signal. Based on this principle, the proposed SERS aptasensor exhibits excellent sensitivity with a detection limit of 7.59×10-13 M for CAP, providing a new strategy for trace detection in food.

Development of an aptasensor for dibutyl phthalate detection and the elucidation of assay inhibition factors

We developed a fluorescence aptasensor (hereafter 'SG-aptasensor') using SYBR Green I, a newly truncated 20-mer aptamer, and probe DNA to detect dibutyl phthalate (DBP). The detection range of DBP was 0.1-100 ng L-1 with 0.08 ng L-1 as the limit of detection. To adapt the assay to environmental samples in the near future, possible inhibition factors (experimental and environmental) have been tested and reported. The experimental inhibitors included the incubation time, temperature, pH, and ionic strength. Consequently, temperature (2-25 °C) and pH (7.0-9.0) ranges did not significantly inhibit the assay. The incubation time required for sufficient reaction was at least 4 h, and a relative humidity <20% may have induced fluorescence quenching. Tris-HCl-based incubation buffer with excess ionic strength (more than 0.2 M NaCl) demonstrated an abnormal increase in fluorescence. Environmental inhibitors including cations (Mg2+, Ca2+, and Cu2+) and humic acids were tested. The fluorescence signal was significantly reduced (∼99%) by 100 mM Cu2+ compared to that by 0 mM Cu2+. In contrast, the reduction in fluorescence signal was marginal (<15%) when Mg2+ or Ca2+ ions were present. Inhibition of the assay was observed (∼28%) in the presence of 100 mg L-1 humic acids.

Carbon-dots encapsulated luminescent metal-organic frameworks@surface molecularly imprinted polymer: A facile fluorescent probe for the determination of chloramphenicol

In this study, carbon dots (CDs)-encapsulated luminescent metal-organic frameworks@surface molecularly imprinted polymer (CDs@MOF@SMIP) was facilely prepared and applied as fluorescent probe for specific identification and sensitive detection of chloramphenicol (CAP) in food. Fluorescent CDs, serving as signal tags, were encapsulated within metal-organic backbones (ZIF-8), yielding luminescent MOF materials (CDs@ZIF-8). The synthesized CDs, CDs@ZIF-8 and CDs@ZIF-8@SMIP were investigated by morphological and structural characterizations (UV-Vis, XRD, FT-IR, BET, TEM). The CDs@ZIF-8@SMIP probe was demonstrated to have remarkable selectivity and sensitivity towards CAP. Its fluorescence decreased linearly with CAP concentration from 0.323 μg L-1 (0.001 μM) to 8075.0 μg L-1 (25.0 μM), featuring a low detection limit of 0.08 μg L-1. The CDs@ZIF-8@SMIP-based fluorescence strategy achieved satisfactory recoveries (95.5 % - 101.0 %) in CAP-spiked commercial foods with RSD < 4.4 % (n = 3). These results indicate that this method can effectively detect trace CAP in food matrices and has broad application prospects.

Analysis and remediation of phthalates in aquatic matrices: current perspectives

Phthalic acid esters (PAEs) are high production volume chemicals used extensively as plasticizers, to increase the flexibility of the main polymer. They are reported to leach into their surroundings from plastic products and are now a ubiquitous environmental contaminant. Phthalate levels have been determined in several environmental matrices, especially in water. These levels serve as an indicator of plasticizer abuse and plastic pollution, and also serve as a route of exposure to different species including humans. Reports published on effects of different PAEs on experimental models demonstrate their carcinogenic, teratogenic, reproductive, and endocrine disruptive effects. Therefore, regular monitoring and remediation of environmental water samples is essential to ascertain their hazard quotient and daily exposure levels. This review summarises the extraction and detection techniques available for phthalate analysis in water samples such as chromatography, biosensors, immunoassays, and spectroscopy. Current remediation strategies for phthalate removal such as adsorption, advanced oxidation, and microbial degradation have also been highlighted.

Magnetic molecularly imprinted polymers integrated ionic liquids for targeted detecting diamide insecticides in environmental water by HPLC-UV following MSPE

Efficiently detecting diamide insecticides in environmental water is challenging due to their low concentrations and complex matrix interferences. In this study, we developed ionic liquids (ILs)-incorporated magnetic molecularly imprinted polymers (IL-MMIPs) for the detection of diamide insecticides, capitalizing on the advantages of ILs and quick magnetic separation through surface imprinting. Tetrachlorantraniliprole was used as the template, and a specific IL, 1-vinyl-3-ethylimidazolium hexafluorophosphate ([VEIm][PF6]), was employed as the functional monomer. Various synthesis conditions were investigated to optimize adsorption efficiency. The prepared IL-MMIPs were successfully employed as adsorbents in magnetic solid-phase extraction (MSPE) to selectively extract, separate, and quantify three types of diamide insecticides from water samples using HPLC-UV detection. Under optimal conditions, the analytical method achieved low limits of detection (0.69 ng mL-1, 0.64 ng mL-1, 0.59 ng mL-1 for cyantraniliprole, chlorantraniliprole and tetrachlorantraniliprole, respectively). The method also displayed a wide linear range (0.003-10 μg mL-1 for cyantraniliprole and chlorantraniliprole, and 0.004-10 μg mL-1 for tetrachlorantraniliprole, respectively) with satisfactory coefficients (R2≥0.9996), and low relative standard deviation (RSD≤2.55%). Additionally, extraction recoveries fell within the range of 79.4%-109%. The results clearly demonstrate that IL-MMIPs exhibit exceptional recognition and rebinding capabilities. The developed IL-MMIPs-MSPE-HPLC-UV method is straightforward and rapid, making it suitable for the detection and analysis of three kinds of diamide insecticides in environmental water.

Molecularly imprinted polymers-aptamer electrochemical sensor based on dual recognition strategy for high sensitivity detection of chloramphenicol

In this paper, an electrochemical sensor based on a dual recognition strategy of molecularly imprinted polymers (MIPs) and aptamer (Apt) has been designed for the high sensitivity detection of chloramphenicol (CAP). Here, MIPs and Apt have provided dual recognition sites to greatly improve the specific recognition ability of the sensor. Chitosan-multi-walled carbon nanotubes (CS-MWNTs) and AuNPs (gold nanoparticles) have been used for their excellent electrical conductivity. When CAP existed in the detection environment, the imprinted cavities with specific recognition ability bound to CAP through forces such as hydrogen bonds. It hindered the rate of electron transfer and resulted in a decrease in current value. Quantitative detection of CAP could be achieved after analyzing the relationship between the concentration of CAP and the change of current value. After optimizing the experimental parameters, the detection range of the sensor was 10-8 g/L-10-2 g/L with the limit of detection of 3.3 × 10-9 g/L, indicating that the sensor had a high practical application potential.

Enzymatic construction Au NPs-rGO based MIP electrochemical sensor for adulteration detection of bovine-derived allergen in camel milk

In this work, a high-performance molecularly imprinted polymer (MIP) sensor for the determination of β-lactoglobulin (β-LG) was fabricated by using trypsin as a template removal reagent. Gold nanoparticles (Au NPs) and reduced graphene oxide (rGO) designed for electrode modification accelerate the heterogeneous electron transfer rate to enhance the sensitivity of the prepared sensor. With enzymatic hydrolysis, β-LG templates were effectively digested into short peptides without damage to the MIP so that the imprinted cavities of the MIP were preserved with a complete spatial structure exhibiting high selectivity. Based on the optimization of the protein removal time and pH, the prepared MIP electrochemical sensor could recognize β-LG in the range of 4-100 ng/mL with a low detection limit (3.58 ng/mL). The sensor also expressed excellent selectivity and was successfully applied to real sample detection. The results demonstrate that the proposed MIP electrochemical sensor may be a promising candidate for camel milk adulteration detection.

Ultrasensitive, Label-Free Voltammetric Detection of Dibutyl Phthalate Based on Poly-l-lysine/poly(3,4-ethylenedioxythiophene)-porous Graphene Nanocomposite and Molecularly Imprinted Polymers

Development of an efficient technique for accurate and sensitive dibutyl phthalate (DBP) determination is crucial for food safety and environment protection. An ultrasensitive molecularly imprinted polymers (MIP) voltammetric sensor was herein engineered for the specific determination of DBP using poly-l-lysine/poly(3,4-ethylenedioxythiophene)/porous graphene nanocomposite (PLL/PEDOT-PG) and poly(o-phenylenediamine)-imprinted film as a label-free and sensing platform. Fabrication of PEDOT-PG nanocomposites was achieved through a simple liquid-liquid interfacial polymerization. Subsequently, poly-l-lysine (PLL) functionalization was employed to enhance the dispersibility and stability of the prepared PEDOT-PG, as well as promote its adhesion on the sensor surface. In the presence of DBP, the imprinted poly(o-phenylenediamine) film was formed on the surface of PLL/PEDOT-PG. Investigation of the physical properties and electrochemical behavior of the MIP/PLL/PEDOT-PG indicates that the incorporation of PG into PEDOT, with PLL uniformly wrapping its surface, significantly enhanced conductivity, carrier mobility, stability, and provided a larger surface area for specific recognition sites. Under optimal experimental conditions, the electrochemical response exhibited a linear relationship with a logarithm of DBP concentration within the range of 1 fM to 5 µM, with the detection limit as low as 0.88 fM. The method demonstrated exceptional stability and repeatability and has been successfully applied to quantify DBP in plastic packaging materials.

Carbon dots-based fluorescent molecularly imprinted photonic crystal hydrogel strip: Portable and efficient strategy for selective detection of tetracycline in foods of animal origin

Rapid, portable, and sensitive detection of tetracycline (TC) is crucial for the environment and human health. In this study, we developed carbon dots (CDs)-based fluorescent molecularly imprinted photonic crystal hydrogel (FMIPH) strips for TC detection in animal-derived foods. CDs emit fluorescent signals, and molecularly imprinted polymers provide specific recognition sites for TC. Inverse opal photonic crystals afford stable 3D macroporous mass transfer channels that considerably reduce binding time between TC and the strips. The portable FMIPH strip exhibited a linear fluorescence response to TC in the concentration range of 0.1-50 μg mL-1, with a detection limit of 0.067 μg mL-1. Good recoveries of TC (93.86-112.59%) were observed in TC-spiked commercially available pork, eggs, and milk. A combination of FMIPH strips with a portable fluorescent reading device could achieve sensitive, on-site, and real-time detection of TC in animal-derived foods.

Molecularly Imprinted Heterostructure-Based Electrochemosensor for Ultratrace and Precise Detection of 2-Methylisoborneol in Water

Ultratrace 2-methylisoborneol (2-MIB, ∼ng/L) in source water is the main odorant in the algae-derived odor episodes, whose accurate on-site detection will have a promising application potential. Due to the chemical inertness of 2-MIB, sensitive and selective detection of 2-MIB remains much challenging. Herein, molecularly imprinted polymer cavities were polymerized on the heterostructure Ti3C2Tx@CuFc-metal-organic framework to selectively capture 2-MIB, where the heterostructure could catalyze the probe redox reaction of [Fe(CN)63-/4-] and amplify the corresponding current signals. The prepared electrochemical sensor showed higher sensitivity on 2-MIB detection than the reported ones. Excellent stability, reusability, and selectivity for 2-MIB detection were also verified. The linear range and limit of detection of our sensor for 2-MIB were optimized to 0.0001-100 μg/L and 30 pg/L, respectively, performing much better than the reported sensors. Comparable performance to gas chromatography-mass spectrometry was achieved when the sensor was applied to real water samples with or without 2-MIB standards. Overall, our research has made great progress in the application of an on-site sensor in 2-MIB detection and well advances the development of molecularly imprinted polymer-based electrochemical sensors.

Conductive imprinted polymeric interfacially modified electrochemical sensors based on covalently bonded layer-by-layer assembly of Gr/Au with flower-like morphology for sensitive detection of 2,4,6-TCP

Polymeric membrane sensors based on molecular imprinted polymers (MIPs) have been attractive analytical tools for detecting organic species. However, the MIPs in electrochemical sensors developed so far are usually prepared by in situ polymerization of pre-polymers and non-covalent adsorption on the surface of the working electrode. Meanwhile, the MIPs in the electrochemical sensors developed are typically made of a non-conductive polymer film. This results in a relatively low current due to the lack of electron transfer. Additionally, the smoothness of the traditional electrochemical substrate results in a low specific surface area, which reduces the sensitivity of the electrochemical sensor. Here, we describe a novel electrochemical sensor with a conductive interface and MIPs modification. The electrochemical sensor was modified by covalent coupled layer by layer self-assembly with the imprinted polymer film. The incorporation of these two conductive functional materials improves the conductivity of the electrodes and provides interface support materials to obtain high specific surface area. By using 2,4,6-trichlorophenol as the model, the sensitivity of the developed conductive sensor was greatly improved compared to that of the traditional MIPs sensor. We believe that the proposed MIPs-based sensing strategy provides a general and convenient method for making sensitive and selective electrochemical sensors.

A review on solution- and vapor-responsive sensors for the detection of phthalates

Phthalic acid esters, largely referred to as phthalates, are today acknowledged as important pollutants used in the manufacture of polyvinyl chloride (PVC)-based plastics, whose use extends to almost every aspect of modern life. The risk of exposure to phthalates is particularly relevant as high concentrations are regularly found in drinking water, food-contact materials and medical devices, motivating an immense body of research devoted to methods for their detection in liquid samples. Conversely, phthalate vapors have only recently been acknowledged as potentially important atmospheric pollutants and as early fire indicators; additionally, deposition of these vapors can pose significant problems to the proper functioning of spacecraft and diverse on-board devices, leading to major space agencies recognizing the need of developing vapor-responsive phthalate sensors. In this manuscript we present a literature survey on solution- and vapor-responsive sensors and analytical assays for the detection of phthalates, providing a detailed analysis of a vast array of analytical data to offer a clear idea on the analytical performance (limits of detection and quantification, linear range) and advantages provided by each class of sensor covered in this review (electrochemical, optical and vapor-responsive) in the context of their potential real-life applications; the manuscript also gives detailed fundamental information on the various physicochemical responses exploited by these sensors and assays that could potentially be harnessed by new researchers entering the field.

Ultrasensitive photoelectrochemical biosensor amplified by target induced assembly of cruciform DNA nanostructure for the detection of dibutyl phthalate

In this work, an ultra-sensitive signal quenched photoelectrochemical (PEC) aptasensor for dibutyl phthalate (DBP) detection was constructed by using a target induced cruciform DNA structure as signal amplifier and g-C₃N₄/SnO₂ composite as signal indicator. Impressively, the designed cruciform DNA structure shows high signal amplification efficiency due to the reduced reaction steric hindrance because of its mutually separated and repelled tails, multiple recognition domains, and a fixed direction for the sequential identification of the target. Therefore, the fabricated PEC biosensor demonstrated a low detection limit of 0.3 fM for DBP in a wide linear range of 1 fM to 1 nM. This work offered a novel nucleic acid signal amplification approach for enhancing the sensitivity of PEC sensing platforms for the detection of phthalates (PAEs)-based plasticizer, laying the foundation for its utilization in the determine of real environmental pollutants.

Construction of AuNPs/reduced graphene nanoribbons co-modified molecularly imprinted electrochemical sensor for the detection of zearalenone

In this work, a highly sensitive and selective molecularly imprinted electrochemical sensor is exploited to detect zearalenone (ZEA) by the synergistic effect of reduced graphene nanoribbons (rGNRs) and gold nanoparticles (AuNPs). The oxidized GNRs are firstly produced by an improved Hummers' oxidation method, and then reduced and modified together with AuNPs onto a glassy carbon electrode by electrodeposition technique to realize collaborative amplification of electrochemical signal. The molecularly imprinted polymer film with specific recognition sites can be generated on the modified electrode by electropolymerization. The effect of experimental conditions is systematically investigated to obtain the best detection performance. It is found that the constructed sensor shows a wide linear range of 1-500 ng·mL^-1 for ZEA with a detection limit as low as 0.34 ng·mL^-1. Obviously, our constructed molecularly imprinted electrochemical sensor shows great potential in the application of precisely detecting ZEA in food.

A Highly Selective Electrochemical Sensor Based on Molecularly Imprinted Copolymer Functionalized with Arginine for the Detection of Chloramphenicol in Honey

Developing an efficient method for chloramphenicol (CAP) detection is of great significance for food safety. Arginine (Arg) was selected as a functional monomer. Benefiting from its excellent electrochemical performance, which is different from traditional functional monomers, it can be combined with CAP to form a highly selective molecularly imprinted polymer (MIP) material. It overcomes the shortcoming of poor MIP sensitivity faced by traditional functional monomers, and achieves high sensitivity detection without compounding other nanomaterials, greatly reducing the preparation difficulty and cost investment of the sensor. The possible binding sites between CAP and Arg molecules were calculated by molecular electrostatic potential (MEP). A low-cost, non-modified MIP electrochemical sensor was developed for the high-performance detection of CAP. The prepared sensor has a wide linear range from 1 × 10^-12 mol L^-1 to 5 × 10^-4 mol L^-1, achieves a very low concentration CAP detection, and the detection limit is 1.36 × 10^-13 mol L^-1. It also exhibits excellent selectivity, anti-interference, repeatability, and reproducibility. The detection of CAP in actual honey samples was achieved, which has important practical value in food safety.

Sensor technologies for the detection and monitoring of endocrine-disrupting chemicals

Endocrine-disrupting chemicals (EDCs) are a class of man-made substances with potential to disrupt the standard function of the endocrine system. These EDCs include phthalates, perchlorates, phenols, some heavy metals, furans, dimethoate, aromatic hydrocarbons, some pesticides, and per- and polyfluoroalkyl substances (PFAS). EDCs are widespread in the environment given their frequent use in daily life. Their production, usage, and consumption have increased many-fold in recent years. Their ability to interact and mimic normal endocrine functions makes them a potential threat to human health, aquatics, and wild life. Detection of these toxins has predominantly been done by mass spectroscopy and/or chromatography-based methods and to a lesser extent by advanced sensing approaches such as electrochemical and/or colorimetric methods. Instrument-based analytical techniques are often not amenable for onsite detection due to the lab-based nature of these detecting systems. Alternatively, analytical approaches based on sensor/biosensor techniques are more attractive because they are rapid, portable, equally sensitive, and eco-friendly. Advanced sensing systems have been adopted to detect a range of EDCs in the environment and food production systems. This review will focus on advances and developments in portable sensing techniques for EDCs, encompassing electrochemical, colorimetric, optical, aptamer-based, and microbial sensing approaches. We have also delineated the advantages and limitations of some of these sensing techniques and discussed future developments in sensor technology for the environmental sensing of EDCs.

Design fabrication of electrochemical sensor based on Ru(bpy)22+/SMWCNTs/Au/GCE electrode for the selective determination of 5′-guanosine monophosphate

5'-Guanosine monophosphate (5'-GMP) is one main source of freshness in broths. Herein, an electrochemical platform based on a novel ternary nanocomposite glassy carbon electrode modified with advantageously-united gold nanoparticles, 2,2'-bipyridine hydrated ruthenium (Ru(bpy)₂Cl₂) and sulfonated multi-walled carbon nanotubes (SMWCNTs)was prepared and used to detect 5'-GMP. After conditions optimization, the best performance of the electrochemical sensor was found in acidic media, including high specificity, sensitivity and selectivity. The electrochemical sensor exhibited a wide linear range under the optimal conditions. The enhanced sensitivity of this sensor was attributed to the Ru(bpy)₂Cl₂ and functionalized SMWCNTs that provided high electrical conductivity and electrocatalytic properties during electrochemical reaction. Precise analysis of 5'-GMP in actual broth samples showed satisfactory recovery. Thus, the sensor can be used in the market and food enterprises.

Graphene Oxide-PAMAM Nanocomposite and Ionic Liquid Modified Carbon Paste Electrode: An Efficient Electrochemical Sensor for Simultaneous Determination of Catechol and Resorcinol

In this paper, a simple strategy was proposed for the analysis of catechol by a carbon paste electrode (CPE) modified with graphene oxide-third generation of poly(amidoamine) dendrimer (GO/G3-PAMAM) nanocomposite and ionic liquid (IL). The synthesis of GO-PAMAM nanocomposite was confirmed using X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), field emission scanning electron microscopy (FE-SEM), and Fourier transform infrared spectroscopy (FT-IR) techniques. The prepared modified electrode (GO-PAMAM/ILCPE) exhibited good performance to detect catechol with a notable decrease in overpotential and increase in current compared with an unmodified CPE. Under optimum experimental conditions, GO-PAMAM/ILCPE electrochemical sensors indicated a lower limit of detection (LOD) of 0.034 μM and a linear response in the concentration range of 0.1 to 200.0 µM for the quantitative measurement of catechol in aqueous solutions. In addition, GO-PAMAM/ILCPE sensor exhibited an ability to simultaneously determine catechol and resorcinol. It can be found that catechol and resorcinol could be completely separated on the GO-PAMAM/ILCPE with the differential pulse voltammetry (DPV) technique. Finally, a GO-PAMAM/ILCPE sensor was utilized to detect catechol and resorcinol in water samples with recoveries of 96.2% to 103.3% and relative standard deviations (RSDs) of less than 1.7%.

Emerging electrochemical techniques for identifying and removing micro/nanoplastics in urban waters

The ubiquitous micro/nanoplastics (MPs/NPs) in urban waters are priority pollutants due to their toxic effects on living organisms. Currently, great efforts have been made to realize a plastic-free urban water system, and the identification and removal of MPs/NPs are two primary issues. Among diverse methods, emerging electrochemical techniques have gained growing interests owing to their facile implementation, high efficiency, eco-compatibility, onsite operation, etc. Herein, recent progress in the electrochemical identification and removal of MPs/NPs in urban waters are comprehensively reviewed. The electrochemical sensing of MPs/NPs and their released pollutants (e.g., bisphenol A (BPA)) has been analyzed, and the sensing principles and the featured electrochemical devices/electrodes are examined. Afterwards, recent applications of electrochemical methods (i.e., electrocoagulation, electroadsorption, electrokinetic separation and electrochemical degradation) in MPs/NPs removal are discussed in detail. The influences of critical parameters (e.g., plastics' property, current density and electrolyte) in the electrochemical identification and removal of MPs/NPs are also analyzed. Finally, the current challenges and prospects in electrochemical sensing and removal of MPs/NPs in urban waters are elaborated. This review would advance efficient electrochemical technologies for future MPs/NPs pollutions management in urban waters.

Novel electrochemical sensor from magnetic carbon dots and cetyltrimethylammonium bromide for sensitive measurement of tetrabromobisphenol A in beverages

Present work depicted a novel electrochemical sensor fabricated with magnetic carbon dots (M-CDs) and cetyltrimethylammonium bromide (CTAB) modified glassy carbon electrode (GCE) for selective measurement of 3,3',5,5'-tetrabromobisphenol A (TBBPA) in beverages. The M-CDs composite material revealed good electrocatalytic activity, and CTAB has strong hydrophobic interaction which enable it have good enrichment capacity of hydrophobic compounds, and combination of them further enhances the electrochemical signal. Hence CTAB decoration can markedly improve the detection performance of TBBPA. Electrochemical properties of the fabricated sensor was investigated through performing cyclic voltammetry (CV). The morphology and functional groups of the modified materials were examined with transmission electron microscope (TEM) and Fourier transform infrared spectroscopy (FTIR). The results indicated that the synthesized material had a spherical-like structure, good dispersion properties and plenty of functional groups on the surface. The effects of incubation potential, incubation time, pH of electrolyte, and scanning rate on oxidation peak current were investigated. Under optimal conditions, the designed sensor had good linear range of 1 nM-1000 nM, and the detection of limit of the constructed sensor was 0.75 nM. The constructed sensor was utilized to detect TBBPA in vitamin water, scream drink and genki forest, and satisfactory detection performance had been achieved.