A label-free electrochemical aptasensor based on AuNPs-loaded zeolitic imidazolate framework-8 for sensitive determination of aflatoxin B1

Iridium oxide-modified reference screen-printed electrodes for point-of-care portable electrochemical cortisol detection

Cortisol is a well-known stress biomarker; this study focuses on using electrochemical immuno-sensing to measure the concentration of cortisol selectively and sensitively in artificial samples. Anti-cortisol antibodies have been immobilised on polycrystalline Au electrodes via strong covalent thiol bonds, fabricating an electrochemical bio-immunosensor for cortisol detection. IrOx was then anodically electrodeposited as a reference electrode on a commercial screen-printed electrode and electrochemical impedance spectrometry (EIS) studies were used to correlate the electrochemical response to cortisol concentration and the induced changes in charge transfer resistance (Rct). A linear relationship between the Rct and the logarithm of cortisol concentration was found in concentrations ranging from 1 ng/mL to 1 mg/mL with limit of detection at 11.85 pg/mL (32.69 pM). The modification of the reference electrode with iridium oxide has greatly improved the reproducibility of the screen-printed electrode. The sensing system can provide a reliable and sensitive detection approach for cortisol measurements.

A pretreatment-free and eco-friendly rapid detection for mycotoxins in edible oils based on magnetic separation technique

Pretreatment steps of current rapid detection methods for mycotoxins in edible oils not only restrict detection efficiency, but also produce organic waste liquid to pollute environment. In this work, a pretreatment-free and eco-friendly rapid detection method for edible oil is established. This proposed method does not require pretreatment operation, and automated quantitative detection could be achieved by directly adding oil samples. According to polarity of target molecules, the content of surfactant in reaction solutions could be adjusted to achieve the quantitative detection of AFB1 in peanut oil and ZEN in corn oil. The recoveries are between 96.5%-110.7% with standard deviation <10.4%, and the limit of detection is 0.17 μg/kg for AFB1 and 4.91 μg/kg for ZEN. This method realizes full automation of the whole chain detection, i.e. sample in-result out, and is suitable for the on-site detection of batches of edible oils samples.

A biosensor integrating the electrochemical and fluorescence strategies for detection of aflatoxin B1 based on a dual-functionalized platform

BACKGROUND

Aflatoxin B1 (AFB1), is a potent hepatic carcinogen which causes cancer by inducing DNA changes in the liver cells. Variety of methods have been developed for detection of AFB1 which are based on single mode detection strategy. Fabrication of novel platform which are compatible for multimodal detection of AFB1 provide robust performance for reliable detection of AFB1. In this study, we aimed to develop a robust biosensing platform that combines electrochemical and fluorescence techniques for the sensitive and specific detection of Aflatoxin B1.

RESULTS

The sensing platform includes the magnetic core-shell Fe3O4@AuNPs and zeolitic imidazolate framework-8 (ZIF-8). In electrochemical mode, the applied voltametric approach was used through functionalization of glassy carbon electrode and exhibited a linear range between 0.5 and 10000 pg mL-1 with LOD of 0.32 pg mL-1. Fluorescence analysis was based on the FRET on/off status of FAM-functionalized aptamer deposited on the same platform. The FAM emission recovered by the addition of AFB1 concentration in the range of 6-60 fg mL-1 with the LOD of 0.20 fg mL-1. The real sample analysis demonstrated satisfactory relative recoveries in the range of 92.81-105.32 % and 91.66-106.66 % using the electrochemical and fluorescence methods, respectively, and its reliability was confirmed by the HPLC technique.

SIGNIFICANCE

The experimental results affirm that the proposed aptasensor serves as a sensitive, efficient, and precise platform for monitoring AFB1 in both electrochemical and fluorescence detection approaches. Proposed strategy showed efficient selectivity among different analytes and was reproducible. Furthermore, the applicability of biosensor was confirmed in food and biological samples.

A sensitive aptasensor mediated by gold nanoparticles/metal organic framework lattice for detection of Pb2+ ion in marine products

Herein, an enzyme-free fluorescent aptasensor was introduced for the ultrasensitive quantification of lead (Pb2+) ion as a hazardous pollutant of the environment and foodstuffs. A nanocomposite of zeolitic imidazolate frameworks-8 and gold nanoparticles (ZIF-8@AuNPs) was utilized as an efficient quencher of the fluorescence intensity of carboxyfluorescein (FAM) signal reporter. The establishment of a hybrid structure between attached aptamer on ZIF-8@AuNPs nanocomposite, and its FAM-tagged complementary (CP) strand decreased the fluorescence response. The preferential binding between the aptamer and Pb2+ released CP strands, which retrieved the fluorescence signal. The aptasensor could assess Pb2+ in the linear concentration range of 1 pM-1 nM with a detection limit (LOD) of 0.24 pM. Besides, it could quantify Pb2+ in various samples, including fish, shrimp, tap water, milk, and serum samples. The developed aptasensor with the superiorities of easiness, cost-effectiveness, easy-to-operate, and rapidness is promising for controlling marine foodstuff safety.

Novel Sensor Approaches of Aflatoxins Determination in Food and Beverage Samples

The rapid quantification of toxins in food and beverage products has become a significant issue in overcoming and preventing many life-threatening diseases. Aflatoxin-contaminated food is one of the reasons for primary liver cancer and induces some tumors and cancer types. Advancements in biosensors technology have brought out different analysis methods. Therefore, the sensing performance has been improved for agricultural and beverage industries or food control processes. Nanomaterials are widely used for the enhancement of sensing performance. The enzymes, molecularly imprinted polymers (MIP), antibodies, and aptamers can be used as biorecognition elements. The transducer part of the biosensor can be selected, such as optical, electrochemical, and mass-based. This review explains the classification of major types of aflatoxins, the importance of nanomaterials, electrochemical, optical biosensors, and QCM and their applications for the determination of aflatoxins.

In silico studies and development of a protein-based electrochemical sensor for selective and sensitive detection of aflatoxin B1

Proteins from different species have been docked with aflatoxin B1 (AFB1) and identified 3 proteins (prostaglandin-E(2)9-reductase from Oryctolagus uniculus, proto-oncogene serine/threonine-protein kinase Pim-1 and human immunoglobulin G (hIgG)) as potential candidates to develop an electrochemical sensor. Fluorescence spectroscopy experiments have confirmed the interaction of hIgG with AFB1 with an affinity constant of 4.6 × 105 M-1. As a proof-of-concept, hIgG was immobilized on carbon nanocomposite (carbon nanotube-nanofiber, CNT-F)-coated glassy carbon electrode (GCE). FT-IR spectra, HR-TEM and BCA assay have confirmed successful immobilization of hIgG on the electrode (hIgG@CNT-F/GCE). The preparation of this protein electrochemical sensor requires only 1 h 36 min, which is fast as compared with preparing an electro immunosensor. hIgG@CNT-F/GCE has displayed an excellent AFB1 limit of detection (0.1 ng/mL), commendable selectivity in the presence of two other mycotoxins (ochratoxin A and patulin) and the detection of  AFB1 in spiked peanuts and corn samples.

Progress on Electrochemical Biomimetic Nanosensors for the Detection and Monitoring of Mycotoxins and Pesticides

Monitoring agricultural toxins such as mycotoxins is crucial for a healthy society. High concentrations of these toxins lead to the cause of several chronic diseases; therefore, developing analytical systems for detecting/monitoring agricultural toxins is essential. These toxins are found in crops such as vegetables, fruits, food, and beverage products. Currently, screening of these toxins is mostly performed with sophisticated instrumentation such as chromatography and spectroscopy techniques. However, these techniques are very expensive and require extensive maintenance, and their availability is limited to metro cities only. Alternatively, electrochemical biomimetic sensing methodologies have progressed hugely during the last decade due to their unique advantages like point-of-care sensing, miniaturized instrumentations, and mobile/personalized monitoring systems. Specifically, affinity-based sensing strategies including immunosensors, aptasensors, and molecular imprinted polymers offer tremendous sensitivity, selectivity, and stability to the sensing system. The current review discusses the principal mechanisms and the recent developments in affinity-based sensing methodologies for the detection and continuous monitoring of mycotoxins and pesticides. The core discussion has mainly focused on the fabrication protocols, advantages, and disadvantages of affinity-based sensing systems and different exploited electrochemical transduction techniques.

A dual-signal ratiometric electrochemical aptasensor based on Thi/Au/ZIF-8 and catalytic hairpin assembly for ultra-sensitive detection of aflatoxin B1

A dual-signal ratiometric electrochemical aptasensor has been developed  for AFB1 detection using thionine/Au/zeolitic imidazolate framework-8 (Thi/Au/ZIF-8) nanomaterials and catalytic hairpin assembly (CHA) reaction. Thi/Au/ZIF-8 combined with DNA hairpin 2 (H2) was used as a signal probe. [Fe(CN)6]3-/4- was served as another signal probe, and the IThi/Au/ZIF-8/I[Fe(CN)6]3-/4- ratio was for the first time utilized to quantify AFB1. AFB1-induced CHA was used to expand the ratio of electrical signals. In the presence of AFB1, H2/Thi/Au/ZIF-8 bound to the electrode via CHA, enhanced  the current signal of Thi/Au/ZIF-8. H2 contained the DNA phosphate backbone hindered [Fe(CN)6]3-/4- redox reaction and resulted in a lower [Fe(CN)6]3-/4- current signal. This aptasensor exhibited high specificity for AFB1, a linear range of 0.1 pg mL-1 to 100 ng mL-1, and a detection limit of 0.089 pg mL-1. It demonstrated favorable sensitivity, selectivity, stability, and repeatability. The aptasensor was suitable for detecting AFB1 in peanuts and black tea and holds potential for real sample applications.

A novel highly active AgMOF-based silver single-atom catalyst and its application to the aptamer SERS/RRS for the determination of aflatoxin B1

A novel highly active silver single-atom catalyst (AgSAC) was prepared by a microwave-assisted solvothermal method using silver covalent organic frameworks (AgMOF) as precursors. It was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), infrared (IR), and surface-enhanced Raman scattering (SERS). The experiment found that AgSAC has excellent catalytic performance and can heavily catalyze the nano-reaction of chloroauric acid-malic acid (HAuCl4-H2Mi) to generate gold nanoparticles (AuNPs). The produced AuNPs have strong SERS, resonance Rayleigh scattering (RRS) and surface plasmon resonance absorption (Abs) signals. Aflatoxin B1 aptamer (AptAFB1) can be adsorbed to the surface of AgSAC through electrostatic interaction, to reduce the catalytic activity of AgSAC and the SERS/RRS/Abs signal of the system. When the target molecule (AFB1) was added, it will specifically bind to AptAFB1 and release AgSAC, restoring the catalytic activity of AgSAC, thereby restoring the SERS/RRS/Abs signal of the system. Based on this, a simple and sensitive aptamer sensing analysis platform for trace AFB1 was established, and a reasonable catalytic amplification mechanism of AgSAC was proposed. The SERS method exhibited the highest sensitivity, with a linear range of 0.005-0.225 μg/L and a detection limit of 0.002 μg/L.

Development of an electrochemical sensitive aptasensor based on a zeolite imidazolate framework-8 and gold nanoparticles for the determination of Staphylococcus aureus bacteria

Staphylococcus aureus (S. aureus) is one of the most important pathogens that cause illness and food poisoning. In this research, using a glassy carbon electrode (GCE) modified with zeolite imidazolate framework-8 (ZIF 8) and gold nanoparticles (AuNPs), a sensitive electrochemical aptasensor has been made for the detection of the S. aureus bacteria. The morphology of the prepared AuNPs-ZIF 8 nanocomposite has been carefully characterized by means of transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), and energy-dispersive X-ray spectroscopy (EDS). In the manufacturing process, the S. aureus aptamer is immobilized on the AuNPs-ZIF 8 surface. Electrochemical impedance spectroscopy (EIS) method has been used for quantitative determination of S. aureus bacteria. The changes in the charge transfer resistance (Rct) of the aptamer due to the change in the concentration of bacteria are considered as the analytical signals. The proposed aptasensor has linear response in the concentration range of 1.5 × 101 to 1.5 × 107 CFU mL-1 of S. aureus bacteria. The detection limit of the method is 3.4 CFU mL-1. Using the developed aptasensor, it is possible to determine S. aureus bacteria in water and milk samples.

Computer aided aptamer selection for fabrication of electrochemical sensor to detect Aflatoxin B1

Aflatoxin B1 (AFB1) is a naturally occurring toxin produced by Aspergillus flavus and Aspergillus parasiticus. The AFB1 is classified as a potent carcinogen and poses significant health risks both to humans and animals. Early detection of the toxin in post-harvest agricultural products will save lives and promote healthy food production. In this study, stratified docking approach was utilized to screen and identify potential aptamers that can bind to AFB1. ssDNA sequences were acquired from the Mendeley dataset, secondary and tertiary structures were predicted through a series of bioinformatics pipelines. Further, the final DNA tertiary structures were minimized and SiteMap algorithm was used to probe and locate binding cavities. According to the final XP docking result, a 34 nt sequence (5'-ATCCTGTGAGGAATGCTCATGCATAGCAAGGGCT-3') aptamer with a docking score of -5.959 kcal/mol was considered for 200 ns MD Simulation. Finally, the screened DNA-aptamer was immobilized over the gold surface based on Au-S chemistry and utilized for the detection of AFB1. The fabricated DNA-aptamer electrode demonstrated a good analytical performance including wide linear range (1.0 to 1000 ng L-1), detection limit (1.0 ng L-1), high stability, and reproducibility.Communicated by Ramaswamy H. Sarma.

Production of AFB1 High-Specificity Monoclonal Antibody by Three-Stage Screening Combined with the De-Homologation of Antibodies and the Development of High-Throughput icELISA

To achieve accurate detection of AFB1 toxin content in agricultural products and avoid false-positive rates in the assays, the specificity of mAbs is critical. We improved the specificity of the prepared monoclonal antibodies by modifying the traditional limiting dilution subcloning method. The traditional finite dilution method was modified with three-stage screening (the trending concentration of standards used in the screening is low-high-low) to achieve high specificity in pre-cell screening and increased the number of subclones to 10 to achieve the de-homologation of antibodies. A modified limiting dilution obtained a highly specific AFB1 monoclonal cell line, ZFG8, with a 50% inhibition concentration (IC50) of 0.3162 ng/mL. Notably, it exhibited the highest specificity compared to anti-AFB1 monoclonal antibodies prepared by other investigators. The maximum cross-reactivity of the mAb with structural analogues for AFB2, AFG1, AFG2, and AFM1 was 0.34%. The results showed that this type of screening improves the monoclonal antibodies' specificity. Based on this ZFG8 monoclonal antibody, an icELISA assay was established with an IC50 of 0.2135 ng/mL for AFB1. The limit of the linear detection range of icELISA is 0.0422-1.29267 ng/mL with reasonable specificity and precision. The recoveries of AFB1 in samples of corn flour and wheat meal ranged from 84 to 107%, with CVs below 9.3%. The recoveries of structural analogues (AFB2, AFM1, AFG1, and AFG2) were less than 10% in both corn flour and wheat meal. The results showed that the prepared AFB1 monoclonal antibody could accurately and specifically recognize AFB1 residues in agricultural products while ignoring the effects of other structural analogues.

Recent Progress of Electrochemical Aptasensors toward AFB1 Detection (2018-2023)

Food contaminants represent possible threats to humans and animals as severe food safety hazards. Prolonged exposure to contaminated food often leads to chronic diseases such as cancer, kidney or liver failure, immunosuppression, or genotoxicity. Aflatoxins are naturally produced by strains of the fungi species Aspergillus, which is one of the most critical and poisonous food contaminants worldwide. Given the high percentage of contaminated food products, traditional detection methods often prove inadequate. Thus, it becomes imperative to develop fast, accurate, and easy-to-use analytical methods to enable safe food products and good practices policies. Focusing on the recent progress (2018-2023) of electrochemical aptasensors for aflatoxin B1 (AFB1) detection in food and beverage samples, without pretending to be exhaustive, we present an overview of the most important label-free and labeled sensing strategies. Simultaneous and competitive aptamer-based strategies are also discussed. The aptasensors are summarized in tabular format according to the detection mode. Sample treatments performed prior analysis are discussed. Emphasis was placed on the nanomaterials used in the aptasensors' design for aptamer-tailored immobilization and/or signal amplification. The advantages and limitations of AFB1 electrochemical aptasensors for field detection are presented.

MnO2 nanoflowers based colorimetric and fluorescent dual-mode aptasensor for sensitive detection of aflatoxin B1 in milk

Aflatoxin B1 (AFB1) with tremendous toxic effects has caused a serious threat to food security. Accurate quantification of AFB1 in food can effectively prevent the risk of human intake of AFB1. Herein, a colorimetric and fluorescent dual-mode aptasensor for accurate and sensitive detection of AFB1 has been developed based on MnO2 nanoflowers (MnO2NFs) for the first time. MnO2NFs could catalyze the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) into blue oxidation product (TMBox) by H2O2, which would be used for visible detection of AFB1. Simultaneously, MnO2NFs can be served as a signal amplifier and reduced by ascorbic acid to generate lots of Mn2+ which would quench the fluorescence of calcein for fluorescent detection of AFB1. Both colorimetric and fluorescent methods have been successfully applied for determination of AFB1 in milk samples with satisfactory results. The proposed dual-mode detection method with high detection sensitivity and accuracy showed great promise for monitoring AFB1 in food.

A novel electrochemical aptasensor based on eco-friendly synthesized titanium dioxide nanosheets and polyethyleneimine grafted reduced graphene oxide for ultrasensitive and selective detection of ciprofloxacin

Developing a rapid, sensitive, and efficient analytical method for the trace-level determination of highly concerning antibiotic ciprofloxacin (CIP) is desirable to guarantee the safety of human health and ecosystems. In this work, a novel electrochemical aptasensor based on polyethyleneimine grafted reduced graphene oxide and titanium dioxide (rGO/PEI/TiO2) nanocomposite was constructed for ultrasensitive and selective detection of CIP. Through the in-situ electrochemical oxidation of Ti3C2Tx nanosheets, TiO2 nanosheets with good electrochemical response were prepared in a more convenient and eco-friendly method. The prepared TiO2 nanosheets promote charge transferring on electrode interface, and [Fe(CN)6]3-/4- as electrochemical active substance can be electrostatically attracted by rGO/PEI. Thus, electrochemical detection signal of the aptasensor variates a lot after specific binding with CIP, achieving working dynamic range of 0.003-10.0 μmol L-1, low detection limit down to 0.7 nmol L-1 (S/N = 3) and selectivity towards other antibiotics. Additionally, the aptasensor exhibited good agreement with HPLC method at 95% confidence level, and achieved good recoveries (96.8-106.3%) in real water samples, demonstrating its suitable applicability of trace detection of CIP in aquatic environment.

Advances in aptamers, and application of mycotoxins detection: A review

Mycotoxin contamination in food products can easily cause serious health hazards and economic losses to human beings. How to accurately detect and effectively control mycotoxin contamination has become a global concern. Mycotoxins conventional detection techniques e.g; ELISA, HPLC, have limitations like, low sensitivity, high cost and time-consuming. Aptamer-based biosensing technology has the advantages of high sensitivity, high specificity, wide linear range, high feasibility, and non-destructiveness, which overcomes the shortcomings of conventional analysis techniques. This review summarizes the sequences of mycotoxin aptamers that have been reported so far. Based on the application of four classic POST-SELEX strategies, it also discusses the bioinformatics-assisted POST-SELEX technology in obtaining optimal aptamers. Furthermore, trends in the study of aptamer sequences and their binding mechanisms to targets is also discussed. The latest examples of aptasensor detection of mycotoxins are classified and summarized in detail. Newly developed dual-signal detection, dual-channel detection, multi-target detection and some types of single-signal detection combined with unique strategies or novel materials in recent years are focused. Finally, the challenges and prospects of aptamer sensors in the detection of mycotoxins are discussed. The development of aptamer biosensing technology provides a new approach with multiple advantages for on-site detection of mycotoxins. Although aptamer biosensing shows great development potential, still some challenges and difficulties are there in practical applications. Future research need high focus on the practical applications of aptasensors and the development of convenient and highly automated aptamers. This may lead to the transition of aptamer biosensing technology from laboratory to commercialization.

Single-Walled Carbon Nanohorn-Based Fluorescence Energy Resonance Transfer Aptasensor Platform for the Detection of Aflatoxin B1

Aflatoxin B1 (AFB1) is one of the most contaminated fungal toxins worldwide and is prone to cause serious economic losses, food insecurity, and health hazards to humans. The rapid, on-site, and economical method for AFB1 detection is need of the day. In this study, an AFB1 aptamer (AFB1-Apt) sensing platform was established for the detection of AFB1. Fluorescent moiety (FAM)-modified aptamers were used for fluorescence response and quenching, based on the adsorption quenching function of single-walled carbon nanohorns (SWCNHs). Basically, in our constructed sensing platform, the AFB1 specifically binds to AFB1-Apt, making a stable complex. This complex with fluorophore resists to be adsorbed by SWCNHs, thus prevent SWCNHs from quenching of fluorscence, resulting in a fluorescence response. This designed sensing strategy was highly selective with a good linear response in the range of 10-100 ng/mL and a low detection limit of 4.1 ng/mL. The practicality of this sensing strategy was verified by using successful spiking experiments on real samples of soybean oil and comparison with the enzyme-linked immunosorbent assay (ELISA) method.

Recent Advances in Electrochemical Biosensors for Food Control

The rapid and sensitive detection of food contaminants is becoming increasingly important for timely prevention and treatment of foodborne disease. In this review, we discuss recent developments of electrochemical biosensors as facile, rapid, sensitive, and user-friendly analytical devices and their applications in food safety analysis, owing to the analytical characteristics of electrochemical detection and to advances in the design and production of bioreceptors (antibodies, DNA, aptamers, peptides, molecular imprinted polymers, enzymes, bacteriophages, etc.). They can offer a low limit of detection required for food contaminants such as allergens, pesticides, antibiotic traces, toxins, bacteria, etc. We provide an overview of a broad range of electrochemical biosensing designs and consider future opportunities for this technology in food control.

Label-Free Electrochemical Aptasensor Based on the Vertically-Aligned Mesoporous Silica Films for Determination of Aflatoxin B1

Herein we report a highly specific electrochemical aptasenseor for AFB1 determination based on AFB1-controlled diffusion of redox probe (Ru(NH₃)₆³⁺) through nanochannels of AFB1-specific aptamer functionalized VMSF. A high density of silanol groups on the inner surface confers VMSF with cationic permselectivity, enabling electrostatic preconcentration of Ru(NH₃)₆³⁺ and producing amplified electrochemical signals. Upon the addition of AFB1, the specific interaction between the aptamer and AFB1 occurs and generates steric hindrance effect on the access of Ru(NH₃)₆³⁺, finally resulting in the reduced electrochemical responses and allowing the quantitative determination of AFB1. The proposed electrochemical aptasensor shows excellent detection performance in the range of 3 pg/mL to 3 μg/mL with a low detection limit of 2.3 pg/mL for AFB1 detection. Practical analysis of AFB1 in peanut and corn samples is also accomplished with satisfactory results by our fabricated electrochemical aptasensor.

Nanoassemblies Based on a Cationic Perylene Diimide Derivative and Sodium Dodecyl Sulfate: A Simple Fluorescent Platform for Efficient Analysis of Aflatoxin B1

Aflatoxin B₁ (AFB₁) is a kind of potently carcinogenic fungal metabolite in food threatening human health, and it is crucial and challenging to develop advanced nonimmune approaches for AFB₁ determination. Addressing this challenge, we successfully constructed a nanoassembly (PdE-PDI/SDS) by noncovalently coupling a cationic perylene diimide derivative (PdE-PDI) and sodium dodecyl sulfate (SDS), exhibiting high-density charges and a specific surface area for rapid sensing of AFB₁. The large electronic conjugate structure and rigid plane of PdE-PDI enable it to form more stable σ-π, π-π coordination, and hydrogen bonds with AFB₁. Additionally, the introduction of SDS significantly amplifies noncovalent interactions and enhances the quenching efficiency of PdE-PDI toward AFB₁. The proposed PdE-PDI/SDS exhibited excellent specificity to AFB₁ and showed dosage-sensitive detection with detection limit as low as 0.74 ng mL^-1. Finally, the PdE-PDI/SDS was successfully applied in cereal samples with good recoveries from 94.61 to 109.92%. To our knowledge, this is the first time a fluorescent strategy from the point of self-assembly for AFB₁ determination is reported, which holds great promise for wide applications of perylene diimide derivative in food safety.

Target-responsive aptamer-cross-linked hydrogel sensors for the visual quantitative detection of aflatoxin B1 using exonuclease I-Triggered target cyclic amplification

•

An AFB₁-responsive aptamer-cross-linked hydrogel sensor was successfully constructed.

•

Dual signal amplification strategy with Encapsulation of enzymesand exonuclease I.

•

This method has great potential for AFB₁ detection in peanut oil.

•

The accuracy and consistency repeatability of this method are close to those of UPLC-HRMS.

For the on-site detection of aflatoxin B₁ (AFB₁), a DNA hydrogel was prepared as a biosensor substrate, while an AFB₁ aptamer was used as the recognition element. An AFB₁-responsive aptamer-cross-linked hydrogel sensor was constructed using an enzyme-linked signal amplification strategy; AFB₁ binds competitively to the aptamer, causing the hydrogel to undergo cleavage and release horseradish peroxidase (HRP). The addition of exonuclease I (ExoI) to the hydrogel causes the release of AFB₁ from the aptamer, promoting additional hydrogel cleavage to release more HRP, ultimately catalysing the reaction between 3,3′,5,5′-tetramethylbenzidine and H₂O₂. The hydrogel sensor exhibited an outstanding sensitivity (limit of detection, 4.93 nM; dynamic range, 0–500 nM), and its selectivity towards seven other mycotoxins was confirmed. The feasibility and reliability were verified by measuring the AFB₁ levels in peanut oil (recoveries, 89.59–95.66 %; relative standard deviation, <7%); the obtained results were comparable to those obtained by UPLC-HRMS.

A novel COOH-GO-COOH-MWNT/pDA/AuNPs based electrochemical aptasensor for detection of AFB1

Aflatoxin B1 (AFB1), one of the most common mycotoxins in food matrixes, has been identified as the most toxic contaminant with mutagenic, teratogenic, immunosuppressive, and carcinogenic effects. In this study, an electrochemical aptamer sensor was developed for the on-site detection of AFB1. Carboxylated graphene oxide (COOH-GO) and carboxylated multi-walled carbon nanotubes (COOH-MWNT) nanocomposites, dopamine polymers (pDA) and gold nanoparticles (AuNPs) were used to enhance the electrochemical activity and the biocompatibility of the screen-printed electrodes (SPE). Once AFB1 was captured by the aptamer immobilized on the electrode surface, the redox current of [Fe(CN)6]3-/4- decreased. Therefore, the binding of aptamer (Apt) and AFB1 can be reflected by the change of the peak current. The as-prepared sensor showed a wide detection range of 0.1 fg ml-1-100 pg ml-1 and a low detection limit of 15.16 ag ml-1. It is also simple and low-cost, which shows great potential in practical application.

Tunable Competitive Absorption-Induced Signal-On Photoelectrochemical Immunoassay for Cardiac Troponin I Based on Z-Scheme Metal-Organic Framework Heterojunctions

Recently emerged Z-scheme heterostructure-based immunoassays have presented new opportunities for photoelectrochemical (PEC) biosensing development. Here, we described a tunable signal-on PEC biosensor for the detection of cardiac troponin I (cTnI), which exploited a competitive absorption effect between Cu(II) ions and a Zr metal-organic framework (Zr-MOF) constructed on TiO₂ nanorods (Cu²⁺@Zr-MOF@TiO₂ NRs). Water-stable Zr-MOF was coated onto TiO₂ NRs on fluorine-doped tin oxide to form a Z-scheme heterostructure substrate (Zr-MOF@TiO₂ NRs), which exhibited a high photoelectric response. Cu²⁺@Zr-MOF@TiO₂ NRs, constructed by loading Cu(II) ions onto the architecture of Zr-MOF by electrostatic interaction, demonstrated a low background signal. After sandwich immunorecognition within a 96-well plate, H₂S, generated by confined alkaline phosphatase on zeolitic imidazolate framework-8, was directed to react with Cu(II) ions to form CuS. This resulted in an in situ change in the photoelectrode and an enhanced photoelectric signal. The developed PEC biosensing platform exhibited high sensitivity and selectivity for the cTnI immunoassay with a detection limit of 8.6 pg/mL. The Z-scheme-based competition absorption modulation of photoelectrochemistry provides a new strategy for general PEC biosensing development.

Recent Progress on Techniques in the Detection of Aflatoxin B1 in Edible Oil: A Mini Review

Contamination of agricultural products and foods by aflatoxin B1 (AFB1) is becoming a serious global problem, and the presence of AFB1 in edible oil is frequent and has become inevitable, especially in underdeveloped countries and regions. As AFB1 results from a possible degradation of aflatoxins and the interaction of the resulting toxic compound with food components, it could cause chronic disease or severe cancers, increasing morbidity and mortality. Therefore, rapid and reliable detection methods are essential for checking AFB1 occurrence in foodstuffs to ensure food safety. Recently, new biosensor technologies have become a research hotspot due to their characteristics of speed and accuracy. This review describes various technologies such as chromatographic and spectroscopic techniques, ELISA techniques, and biosensing techniques, along with their advantages and weaknesses, for AFB1 control in edible oil and provides new insight into AFB1 detection for future work. Although compared with other technologies, biosensor technology involves the cross integration of multiple technologies, such as spectral technology and new nano materials, and has great potential, some challenges regarding their stability, cost, etc., need further studies.