A simple and rapid biosensor for ochratoxin A based on a structure-switching signaling aptamer

A label-free ratiometric homogeneous electrochemical aptasensor based on dual catalytic hairpin self-assembly for rapid and sensitive detection of ochratoxin A in food

The food contamination with Ochratoxin A (OTA) has highlighted the need to create precise, sensitive, and convenient techniques. Herein, we proposed a label-free and immobilization-free ratiometric homogeneous electrochemical aptasensor based on dual catalytic hairpin self-assembly (CHA) for OTA detection. Methylene blue (MB) and ferrocene (Fc) in solution were utilized as label-free signaling molecules, generating a response signal (IMB) and a reference signal (IFc), respectively. The ratio of IMB/IFc was utilized as a measure to quantify OTA. Dual CHA was exploited to increase the ratiometric signal and enhance the amplification efficiency. This aptasensor achieved trace-level detection for OTA over a linear range of lower concentrations (1.0 × 10-3 ng/mL-1.0 × 103 ng/mL) with LOD of 92 fg/mL. The aptasensor was successfully applied to detect OTA in cereal and wine, with comparable results of HPLC-MS/MS. This strategy provided a viable platform for rapid, sensitive, and accurate detection of OTA in food.

Developing Microelectrode Arrays for the Point-of-Care Multiplex Detection of Metabolites

DNA-aptamer-functionalized electrode arrays can provide an intriguing method for detecting pathogen-derived exometabolites. This work addresses the limitations of previous aptamer-based pathogen detection methods by introducing a novel surface design that bridges the gap between initial efforts in this area and the demands of a point-of-care device. Specifically, the use of a diblock copolymer coating on a high-density microelectrode array and Cu-mediated cross coupling reactions that allow for the exclusive functionalization of that coating by any electrode or set of electrodes in the array provides a device that is stable for 1 year and compatible with the multiplex detection of small-molecule targets. The new chemistry developed allows one to take advantage of a large number of electrodes in the array with one experiment described herein capitalizing on the use of 960 individually addressable electrodes.

Rational Approach to Optimizing Conformation-Switching Aptamers for Biosensing Applications

The utilization of structure-switching aptamers (SSAs) has enabled the development of novel sensing platforms for the sensitive and continuous detection of molecules. De novo development of SSAs, however, is complex and laborious. Here we describe a rational approach to SSA optimization that simultaneously improves aptamer binding affinity and introduces target-dependent conformation-switching for compatibility with real-world biosensor applications. Key structural features identified from NMR and computational modeling were used to optimize conformational switching in the presence of target, while large-scale, microarray-based mutation analysis was used to map regions of the aptamer permissive to mutation and identify combinations of mutations with stronger binding affinity. Optimizations were carried out in a relevant biofluid to ensure a seamless transition of the aptamer to a biosensing platform. Initial proof-of-concept for this approach is demonstrated with a cortisol binding aptamer but can easily be translated to other relevant aptamers. Cortisol is a hormone correlated with the stress response that has been associated with various medical conditions and is present at quantifiable levels in accessible biofluids. The ability to continuously track levels of stress in real-time via cortisol monitoring, which can be enabled by the aptamers reported here, is crucial for assessing human health and performance.

Microelectrode Arrays, Electrocatalysis, and the Need for Proper Characterization

Indirect electrochemical methods are a powerful tool for synthetic chemistry because they allow for the optimization of chemical selectivity in a reaction while maintaining the advantages of electrochemistry in terms of sustainability. Recently, we have found that such methods provide a handle for not only the synthesis of complex molecules, but also the construction of complex, addressable molecular surfaces. In this effort, the indirect electrochemical methods enable the placement or synthesis of molecules by any electrode or set of electrodes in a microelectrode array. The success of these surface-based reactions are typically evaluated with the use of fluorescence labelling studies. However, these fluorescence-based evaluations can be misleading. While they are excellent for determining that a reaction has occurred in a site-selective fashion on an array, they do not provide information on whether that reaction is the one desired or how well it worked. We describe here how the use of a "safety-catch" linker strategy allows for a more accurate assessment of reaction quality on an array, and then use that capability to illustrate how the use of transition metal mediated cross-coupling reactions on an array prevent unwanted background reactions that can occur on a polymer-coated electrode surface. The method enables a unique level of quality control for array-based transformations.

Target-initiated fluorescent aptasensor based on multisite strand displacement amplification for label-free detection of ochratoxin A

We developed a fluorescent aptasensor for label-free detection of ochratoxin A (OTA) based on TdT- and DNA polymerase-assisted multisite strand displacement amplification. This aptasensor exhibits good specificity and high sensitivity with a limit of detection (LOD) of 0.18 ng mL-1, and it can be further applied for the accurate quantification of OTA in complex real samples, holding promising applications in the field of food safety.

Fluorescent aptasensor for the ultrasensitive detection of antibiotic residue in food samples based on dumbbell DNA-mediated signal amplification

Sensitive and reliable detection of antibiotics is of great significance for environmental and food safety due to its high risk in trace concentrations. Herein, we developed a fluorescence sensing system for chloramphenicol (CAP) detection based on dumbbell DNA-mediated signal amplification. Two hairpin dimers (2H1 and 2H2) were employed as the building blocks to construct the sensing scaffolds. The CAP-aptamer binding in another hairpin H0 can liberate the trigger DNA, which then activates the cyclic assembly reaction between 2H1 and 2H2. The separation of FAM and BHQ in the formed product of cascaded DNA ladder yields a high fluorescence signal for CAP monitoring. Compared with the monomer hairpin assembly between H1 and H2, the dimer hairpin assembly between 2H1 and 2H2 exhibits enhanced signal amplification efficiency and reduced reaction time. The developed CAP sensor showed a wide linear range from 10 fM to 10 nM with a detection limit of 2 fM. Importantly, this sensing platform has been successfully applied to the determination of CAP in fish, milk, and water samples with satisfactory recovery and accuracy. With the advantages of high sensitivity, mix-and-read pattern, and robustness, our proposed CAP sensor can be used as a simple and routine tool for the detection of trace amounts of antibiotic residues.

Recent advances in simultaneous detection strategies for multi-mycotoxins in foods

Mycotoxin contamination has become a challenge in the field of food safety testing, given the increasing emphasis on food safety in recent years. Mycotoxins are widely distributed, in heavily polluted areas. Food contamination with these toxins is difficult to prevent and control. Mycotoxins, as are small-molecule toxic metabolites produced by several species belonging to the genera Aspergillus, Fusarium, and Penicillium growing in food. They are considered teratogenic, carcinogenic, and mutagenic to humans and animals. Food systems are often simultaneously contaminated with multiple mycotoxins. Due to the additive or synergistic toxicological effects caused by the co-existence of multiple mycotoxins, their individual detection requires reliable, accurate, and high-throughput techniques. Currently available, methods for the detection of multiple mycotoxins are mainly based on chromatography, spectroscopy (colorimetry, fluorescence, and surface-enhanced Raman scattering), and electrochemistry. This review provides a comprehensive overview of advances in the multiple detection methods of mycotoxins during the recent 5 years. The principles and features of these techniques are described. The practical applications and challenges associated with assays for multiple detection methods of mycotoxins are summarized. The potential for future development and application is discussed in an effort, to provide standards of references for further research.

Combating small molecule environmental contaminants: detection and sequestration using functional nucleic acids

Small molecule contaminants pose a significant threat to the environment and human health. While regulations are in place for allowed limits in many countries, detection and remediation of contaminants in more resource-limited settings and everyday environmental sources remains a challenge. Functional nucleic acids, including aptamers and DNA enzymes, have emerged as powerful options for addressing this challenge due to their ability to non-covalently interact with small molecule targets. The goal of this perspective is to outline recent efforts toward the selection of aptamers for small molecules and describe their subsequent implementation for environmental applications. Finally, we provide an outlook that addresses barriers that hinder these technologies from being widely adopted in field friendly settings and propose a path forward toward addressing these challenges.

Ultrasensitive Detection of Ochratoxin A With a Zeolite Imidazolate Frameworks Composite–Based Electrochemical Aptasensor

Ochratoxin A (OTA) is a harmful mycotoxin, which is mainly secreted by Penicillium and Aspergillus species. In this work, an electrochemical aptasensor is presented for OTA detection based on Au nanoparticles (AuNPs) modified zeolite imidazolate frameworks (ZIFs) ZIF-8 platform and duplex-specific nuclease (DSN) triggered hybridization chain reaction (HCR) signal amplification. G-quadruplex-hemin assembled HCR nanowire acted as a nicotinamide adenine dinucleotide (NADH) oxidase and an HRP-mimicking DNAzyme. Besides, thionine (Thi) was enriched as a redox probe for signal amplification in this pseudobienzyme electrocatalytic system. Under the optimal conditions, the analytical response ranged from 1 to 10⁷ fg ml⁻¹ with a detection limit of 0.247 fg ml⁻¹. Furthermore, the aptasensor was proven to be applied in real wheat samples with a recovery between 96.8 and 104.2%, illustrating the potential prospects in practical detection.

Stimuli-responsive assembly of bilingual peptide nucleic acids

Peptide nucleic acids (PNAs) are high-affinity synthetic nucleic acid analogs capable of hybridization with native nucleic acids. PNAs synthesized having amino acid sidechains installed at the γ-position along the backbone provide a template for a single biopolymer to simultaneously encode nucleic acid and amino acid sequences. Previously, we reported the development of “bilingual” PNAs through the synthesis of an amphiphilic sequence featuring separate blocks of hydrophobic and hydrophilic amino acid functional groups. These PNAs combined the sequence-specific binding activity of nucleic acids with the structural organization properties of peptides. Like other amphiphilic compounds, these γ-PNAs were observed to assemble spontaneously into micelle-like nanostructures in aqueous solutions and disassembly was induced through hybridization to a complementary sequence. Here, we explore whether assembly of these bilingual PNAs is possible by harnessing the nucleic acid code. Specifically, we designed an amphiphile-masking duplex system in which spontaneous amphiphile assembly is prevented through hybridization to a nucleic acid masking sequence. We show that the amphiphile is displaced upon introduction of a releasing sequence complementary to the masking sequence through toehold mediated displacement. Upon release, we observe that the amphiphile proceeds to assemble in a fashion consistent with our previously reported structures. Our approach represents a novel method for controlled stimuli-responsive assembly of PNA-based nanostructures.

“Bilingual” biopolymers comprised of γ-modified peptide nucleic acids can harness peptide and nucleic acid codes to direct assembly and recognition. Herein, we demonstrate stimuli-responsive assembly through a toehold-mediated displacement motif.

RE-SELEX: restriction enzyme-based evolution of structure-switching aptamer biosensors

Aptamers are widely employed as recognition elements in small molecule biosensors due to their ability to recognize small molecule targets with high affinity and selectivity. Structure-switching aptamers are particularly promising for biosensing applications because target-induced conformational change can be directly linked to a functional output. However, traditional evolution methods do not select for the significant conformational change needed to create structure-switching biosensors. Modified selection methods have been described to select for structure-switching architectures, but these remain limited by the need for immobilization. Herein we describe the first homogenous, structure-switching aptamer selection that directly reports on biosensor capacity for the target. We exploit the activity of restriction enzymes to isolate aptamer candidates that undergo target-induced displacement of a short complementary strand. As an initial demonstration of the utility of this approach, we performed selection against kanamycin A. Four enriched candidate sequences were successfully characterized as structure-switching biosensors for detection of kanamycin A. Optimization of biosensor conditions afforded facile detection of kanamycin A (90 μM to 10 mM) with high selectivity over three other aminoglycosides. This research demonstrates a general method to directly select for structure-switching biosensors and can be applied to a broad range of small-molecule targets.

Synthetic biology-inspired strategies and tools for engineering of microbial natural product biosynthetic pathways

Microbial-derived natural products (NPs) and their derivative products are of great importance and used widely in many fields, especially in pharmaceutical industries. However, there is an immediate need to establish innovative approaches, strategies, and techniques to discover new NPs with novel or enhanced biological properties, due to the less productivity and higher cost on traditional drug discovery pipelines from natural bioresources. Revealing of untapped microbial cryptic biosynthetic gene clusters (BGCs) using DNA sequencing technology and bioinformatics tools makes genome mining possible for NP discovery from microorganisms. Meanwhile, new approaches and strategies in the area of synthetic biology offer great potentials for generation of new NPs by engineering or creating synthetic systems with improved and desired functions. Development of approaches, strategies and tools in synthetic biology can facilitate not only exploration and enhancement in supply, and also in the structural diversification of NPs. Here, we discussed recent advances in synthetic biology-inspired strategies, including bioinformatics and genetic engineering tools and approaches for identification, cloning, editing/refactoring of candidate biosynthetic pathways, construction of heterologous expression hosts, fitness optimization between target pathways and hosts and detection of NP production.

Design, Simulation, and Development of a BioSensor for Viruses Detection Using FPGA

Objective: Impedance based biosensing provides a unique, highly sensitive electrical approach to biomolecule detection, cell growth, and other biological events. To date, an impedance change due to the cell growth has been considered as a solution to detect some changes in a cell’s behavior. The impedance change detection is normally measured via an impedance analyzer which is expensive and also cumbersome. Rapid and definitive diagnosis of viral infections is imperative in patient treatment process. Early detection followed by appropriate lifestyle and treatment may result to a longer, healthier life. Certain patients require continues monitoring that may require regular visits to hospitals which is not practical. Therefore, a continuous home healthcare device is needed to monitor and detect any change in a patient’s health condition. Methods & Results: In this research, a novel sensor and healthcare monitoring system is modeled, simulated, developed, and tested to detect viruses by detecting the change in the impedance due to antibodies and antigens binding. First, COMSOL simulation tool is used to develop a model to prove the concept. The model predicts increasing impedance during functionalization of electrodes with antibodies and after antigen binding steps. Second, to understand how nanoscale electrode size and spacing would affect biosensing assay (antibody-based affinity binding of a protein antigen), a model using COMSOL is developed. Third, Field Programmable Gate Arrays (FPGA) based signal processing system is developed as well to be connected to analog to digital converter (ADC) to acquire the current and voltage readings of the sensors over time. This healthcare monitoring system is used to continuously monitoring a patient’s condition and reports any changes in the impedance readings which represents virus detection or at least change in the cell’s behavior. Conclusions: The proposed sensor model is simulated, tested and verified via COMSOL and the FPGA prototype is tested and it verified the COMSOL model. This work reports that the proposed sensor can be used to detect viruses via detecting a change in the impedance.

Biosensor Design for Detection of Mercury in Contaminated Soil Using Rhamnolipid Biosurfactant and Luminescent Bacteria

In this study, a biosensor is designed to remove mercury as a toxic metal contaminant from the soil. The rhamnolipid biosurfactant was used to extract the mercury sorbed to soil to the aqueous phase. An immobilized bioluminescent bacterium (Escherichia coli MC106) with pmerRBPmerlux plasmid is assisted for mercury detection. A significant decrease in luminescence level was observed in a biosensor system containing contaminated soil sample extract. The concentrations of extracting mercury are well correlated with the mercury toxicity data obtained from experimental biosensor systems according to the RBL value. The optimum aeration rate of 20 ml/min was obtained for the biosensor systems. The advantage of such a biosensor is the in situ quantification of mercury as a heavy metal contaminant in soils. Therefore, this system could be proposed as a good biosensor-based alternative for future detection of heavy toxic metals in soils.

A competitive fluorescence assay based on free-complementary DNA for ochratoxin A detection

An ultrasensitive, rapid, and specific method for Ochratoxin A (OTA) detection was designed using complementary sequence to aptamer as a target of molecular beacon (MB). The designed loop structure of the MB has the same sequence as the aptamer with a complementary DNA (cDNA) which translates the level of the target into a measurable response. The presence of the target holds aptamer at the corresponding amount and the additional cDNAs are consumed by unbound aptamers which avails free cDNAs that resulting in fluorescence rising due to unfolding of MBs. Under the optimized conditions, the fluorescence intensity increased linearly with OTA concentration over the range of 10 pg mL^-1-1 µg mL^-1 with the detection limit of 0.247 pg mL^-1. The application of this assay in wheat sample in comparison with HPLC-MS/MS method, demonstrated that the new assay could be a potential sensing platform for OTA detection.

Development of a DNA-based biosensor for the fast and sensitive detection of ochratoxin A in urine

In this paper, a novel DNA-based biosensor is proposed, which is based on paramagnetic microbeads carrying an ochratoxin A (OTA) capture aptamer. A sandwich-like detection complex is linked to the capture aptamer and is able to trigger, in presence of OTA, an isothermal rolling circle amplification (RCA) reaction. This latter generated autocatalytic units with a peroxidase activity (DNAzyme) that, in presence of a proper substrate, gave a blue-coloured product visible by the naked eye. The capture aptamer, blocked onto magnetic beads, allowed the specific capture of OTA in liquid samples. The modified detection aptamer, annealed to a circularized probe, was then used to detect the toxin capture event. Indeed, in the presence of OTA and an isothermal enzyme, the circular DNA was amplified, producing a single-stranded and tandem repeated long homologous copy of its sequence. In the DNA strand, a self-catalytic structure was formed with hemin as the catalytic core, inducing the development of blue colour in the presence of ABTS and hydrogen peroxide. The results showed that the biosensor has high sensitivity and selectivity for the detection of OTA, as low as 1.09 × 10^-12 ng/mL. Moreover, the proposed biosensor was successfully used for the detection of OTA in naturally contaminated rat urine. Accuracy and repeatability data obtained in recovery experiments were satisfying, being recoveries >95% with relative standard deviations in the range 3.6-15%. For the first time, an aptasensor was successfully applied to detect OTA in biological fluids. It can be used for mycotoxin biomonitoring and assessment of individual exposure.

Detection Strategies of Zearalenone for Food Safety: A Review

Zearalenone (ZEN) is a toxic compound produced by the metabolism of fungi (genus Fusarium) that threaten the food and agricultural industry belonging to the in foods and feeds. ZEN has toxic effects on human and animal health due to its mutagenicity, teratogenicity, carcinogenicity, nephrotoxicity, immunotoxicity, and genotoxicity. To ensure food safety, rapid, precise, and reliable analytical methods can be developed for the detection of toxins such as ZEN. Different selective molecular diagnostic elements are used in conjunction with different detection strategies to achieve this goal. In this review, the use of electrochemical, colorimetric, fluorometric, refractometric as well as other strategies were discussed for ZEN detection. The success of the sensors in analytical performance depends on the development of receptors with increased affinity to the target. This requirement has been met with different immunoassays, aptamer-assays, and molecular imprinting techniques. The immobilization techniques and analysis strategies developed with the combination of nanomaterials provided high precision, reliability, and convenience in ZEN detection, in which electrochemical strategies perform the best.

A Non-Enzyme and Non-Label Sensitive Fluorescent Aptasensor Based on Simulation-Assisted and Target-Triggered Hairpin Probe Self-Assembly for Ochratoxin a Detection

The monitoring and control of mycotoxins has caused widespread concern due to their adverse effects on human health. In this research, a simple, sensitive and non-label fluorescent aptasensor has been reported for mycotoxin ochratoxin A (OTA) detection based on high selectivity of aptamers and amplification of non-enzyme hybridization chain reaction (HCR). After the introduction of OTA, the aptamer portion of hairpin probe H1 will combine with OTA to form OTA-aptamer complexes. Subsequently, the remainder of the opened H1 will act as an initiator for the HCR between the two hairpin probes, causing H1 and H2 to be sequentially opened and assembled into continuous DNA duplexes embedded with numerous G-quadruplexes, leading to a significant enhancement in fluorescence signal after binding with N-methyl-mesoporphyrin IX (NMM). The proposed sensing strategy can detect OTA with concentration as low as 4.9 pM. Besides, satisfactory results have also been obtained in the tests of actual samples. More importantly, the thermodynamic properties of nucleic acid chains in the monitoring platform were analyzed and the reaction processes and conditions were simulated before carrying out biological experiments, which theoretically proved the feasibility and simplified subsequent experimental operations. Therefore, the proposed method possess a certain application value in terms of monitoring mycotoxins in food samples and improving the quality control of food security.

A new chemiluminescence method for the determination of 8-hydroxyguanine based on l-histidine bound nickel nanoparticles

A new chemiluminescence aptasensor for sensitive and efficient detection of 8-hydroxyguanine based on the synergistic interaction of Ni NPs@l-histidine@aptamer@MBs has been developed, and it has been applied in the real urine samples of cancer patients.

Probing the Mechanism of Structure-Switching Aptamer Assembly by Super-Resolution Localization of Individual DNA Molecules

Oligonucleotide aptamers can be converted into structure-switching biosensors by incorporating a short, typically labeled oligonucleotide that is complementary to the analyte-binding region. Binding of a target analyte can disrupt the hybridization equilibrium between the aptamer and the labeled-complementary oligo producing a concentration-dependent signal for target-analyte sensing. Despite its importance in the performance of a biosensor, the mechanism of analyte-response of most structure-switching aptamers is not well understood. In this work, we employ single-molecule fluorescence imaging to investigate the competitive kinetics of association of a labeled complementary oligonucleotide and a target analyte, l-tyrosinamide (L-Tym), interacting with an L-Tym-binding aptamer. The complementary readout strand is fluorescently labeled, allowing us to measure its hybridization kinetics with individual aptamers immobilized on a surface and located with super-resolution techniques; the small-molecule L-Tym analyte is not labeled in order to avoid having an attached dye molecule impact its interactions with the aptamer. We measure the association kinetics of unlabeled L-Tym by detecting its influence on the hybridization of the labeled complementary strand. We find that L-Tym slows the association rate of the complementary strand with the aptamer but does not impact its dissociation rate, suggesting an S_N1-like mechanism where the complementary strand must dissociate before L-Tym can bind. The competitive model revealed a slow association rate between L-Tym and the aptamer, producing a long-lived L-Tym-aptamer complex that blocks hybridization with the labeled complementary strand. These results provide insight about the kinetics and mechanism of analyte recognition in this structure-switching aptamer, and the methodology provides a general means of measuring the rates of unlabeled-analyte binding kinetics in aptamer-based biosensors.

Aptamer-Based Biosensor for Detection of Mycotoxins

Mycotoxins are a large type of secondary metabolites produced by fungi that pose a great hazard to and cause toxic reactions in humans and animals. A majority of countries and regulators, such as the European Union, have established a series of requirements for their use, and they have also set maximum tolerance levels. The development of high sensitivity and a specific analytical platform for mycotoxins is much in demand to address new challenges for food safety worldwide. Due to the superiority of simple, rapid, and low-cost characteristics, aptamer-based biosensors have successfully been developed for the detection of various mycotoxins with high sensitivity and selectivity compared with traditional instrumental methods and immunological approaches. In this article, we discuss and analyze the development of aptasensors for mycotoxins determination in food and agricultural products over the last 11 years and cover the literatures from the first report in 2008 until the present time. In addition, challenges and future trends for the selection of aptamers toward various mycotoxins and aptasensors for multi-mycotoxins analyses are summarized. Given the promising development and potential application of aptasensors, future research studies made will witness the great practicality of using aptamer-based biosensors within the field of food safety.

A Lateral Flow Strip Based on a Truncated Aptamer-Complementary Strand for Detection of Type-B Aflatoxins in Nuts and Dried Figs

Type-B aflatoxins (AFB1 and AFB2) frequently contaminate food, especially nuts and fried figs, and seriously threaten human health; hence, it is necessary for the newly rapid and sensitive detection methods to prevent the consumption of potentially contaminated food. Here, a lateral flow aptasensor for the detection of type-B aflatoxins was developed. It is based on the use of fluorescent dye Cy5 as a label for the aptamer, and on the competition between type-B aflatoxins and the complementary DNA of the aptamer. This is the first time that the complementary strand of the aptamer has been used as the test line (T-line) to detect type-B aflatoxins. In addition, the truncated aptamer was used to improve the affinity with type-B aflatoxins in our study. Therefore, the lengths of aptamer and cDNA probe were optimized as key parameters for higher sensitivity. In addition, binding buffer and organic solvent were investigated. The results showed that the best pair for achieving improved sensitivity and accuracy in detecting AFB1 was formed by a shorter aptamer (32 bases) coupled with the probe complementary to the AFB1 binding region of the aptamer. Under the optimal experimental conditions, the test strip showed an excellent linear relationship in the range from 0.2 to 20 ng/mL with a limit of detection of 0.16 ng/mL. This aptamer-based strip was successfully applied to the determination of type-B aflatoxins in spiked and commercial peanuts, almonds, and dried figs, and the recoveries of the spiked samples were from 93.3%-112.0%. The aptamer-complementary strand-based lateral flow test strip is a potential alternative tool for the rapid and sensitive detection of type-B aflatoxins in nuts and dried figs. It is of help for monitoring aflatoxins to avoid the consumption of unsafe food.

Intrinsic "Turn-On" Aptasensor Detection of Ochratoxin A Using Energy-Transfer Fluorescence

Ochratoxin A (OTA) is an intrinsically fluorescent phenolic mycotoxin that contaminates a wide range of food products and is a serious health threat to animals and humans. An OTA binding aptamer (OTABA) that folds into an antiparallel G-quadruplex (GQ) in the absence and presence of target OTA has been incorporated into a vast variety of aptasensor platforms for OTA detection. The development of a simple, aptamer-based approach would allow for detection of the toxin without the use of complex analytical instrumentation, which has been the gold standard for OTA detection thus far. However, to date, none of the aptasensor platforms have utilized the natural fluorescence of the phenolic toxin for detection. Herein, we report that OTA binding to OTABA involves π-stacking interactions that lead to GQ-to-toxin energy transfer (ET), which affords a "turn-on" fluorescence self-signaling platform in which the emission of the aptamer-target complex is enhanced in comparison to the free toxin alone. Selective excitation of the GQ-OTA complex at 256 nm leads to a 4-fold enhancement in OTA fluorescence. The GQ-OTA ET detection platform boasts a limit of detection ∼2 ng/mL, which is comparable to a previously demonstrated fluorescence resonance energy transfer immunoassay platform for OTA detection, and displays excellent OTA selectivity and recovery from red wine samples.

Predicting Future Prospects of Aptamers in Field-Effect Transistor Biosensors

Aptamers, in sensing technology, are famous for their role as receptors in versatile applications due to their high specificity and selectivity to a wide range of targets including proteins, small molecules, oligonucleotides, metal ions, viruses, and cells. The outburst of field-effect transistors provides a label-free detection and ultra-sensitive technique with significantly improved results in terms of detection of substances. However, their combination in this field is challenged by several factors. Recent advances in the discovery of aptamers and studies of Field-Effect Transistor (FET) aptasensors overcome these limitations and potentially expand the dominance of aptamers in the biosensor market.

Aptamer-based Homogeneous Analysis for Food Control

Background:

Highly sensitive and rapid analysis of food contaminants is of great significance for food safety control. Aptamer is a new kind of recognition molecules which could be applied for constructing homogeneous analysis assays, potentially achieving highly sensitive, cheap and rapid profiling of food contaminants.

Methods:

An overview of the literature concerning the homogeneous analysis of food contaminations based on aptamers has been reviewed (focused on the most recent literature, 2000-2018).

Results:

Attributed to aptamer’s controllability, designability and feasibility for the adoption of nucleic acid amplification, rapid, highly sensitive homogeneous assay for various food contaminants could be constructed. The structure-switching aptamer probe would confer quick, efficient and specific response to target food contaminants. Besides, the capability of amplification of aptamer sequences or nucleic acid probes would lead to highly sensitive detection.

Conclusion:

Aptamer-based homogeneous analysis methods have already been applied to detect various food contaminations ranging from toxins, heavy metal and pesticide to allergen and pathogenic bacteria. However, it is still a challenge to achieve robust and accurate detection of food contaminants in complex food samples.

Super-Resolution Imaging of Competitive Unlabeled DNA Hybridization Reveals the Influence of Fluorescent Labels on Duplex Formation and Dissociation Kinetics

Single-molecule fluorescence imaging is a powerful method to measure reversible reaction kinetics, allowing one to monitor the bound state of individual probe molecules with fluorescently labeled targets. In the case of DNA hybridization, previous studies have shown that the presence of a fluorescent label on a target strand can exhibit significant influence on the stability of a DNA duplex that is formed. In this work, we have developed a super-resolution imaging method to measure the hybridization kinetics of unlabeled target DNA that compete with a fluorescently labeled tracer DNA strand to hybridize with an unlabeled probe DNA immobilized at a surface. The hybridization of an unlabeled DNA target cannot be detected directly, but its presence blocks the immobilized probe DNA, influencing the measured time intervals between labeled DNA hybridization events. We derive a model for competitive hybridization kinetics to extract the association and dissociation rate constants of the unlabeled species from the distribution of time intervals between hybridization events of the labeled tracer DNA at individual localized DNA probe sites. We use this methodology to determine the hybridization kinetics of a model 11-mer unlabeled target DNA strand and then determine how five different fluorescent labels attached to the same target DNA strand impact the hybridization kinetics. Compared to the unlabeled target, these labels can slow the association and dissociation rates by as much as a factor of 5. The super-resolution time-interval methodology provides a unique approach to determining fundamental (label-free) rates of DNA hybridization, revealing the significant influence of fluorescent labels on these kinetics. This measurement concept can be extended to studies of other reversible reaction systems, where kinetics of unlabeled species can be determined from their influence on the reaction of a labeled species with localized probe molecules on a surface.

A label-free aptasensor for turn-on fluorescent detection of ochratoxin A based on aggregation-induced emission probe

A novel label-free fluorescence aptasensor used for the detection of ochratoxin A (OTA) is presented in this study. When aggregated on the surface of DNA aptamer, aggregation-induced emission (AIE) fluorescence probe presents turn-on fluorescence property. The method proposed in this article was based on an AIE probe, 4, 4-(1E,1E)-2, 2-(anthracene-9, 10-diyl) bis (ethene-2, 1-diyl) bis (N, N, N-trimethylbenzenaminium iodide) (DSAI). With OTA present, the aptamer will combine with OTA and the conformation of the aptamer will switch to an antiparallel G-quadruplex from the initial random coil, which obstructs its digestion by Exo I. After the solution is added with DSAI, DSAI will aggregate on the surface of the aptamer/OTA complex and produces a strong emission. In the range of 5 to 500 ng · ml^-1 OTA concentrations, the fluorescence increases with a linear logarithm relationship. The detection limit is 1.9 ng · ml^-1. This method was used to detect OTA in spiked real samples, with recoveries and RSDs in the range of 92.2% to 106.3%, and 2.7% to 5.2%, respectively.

Antibodies Versus Aptamers: A Comparative View

Antibodies are large proteins generated in vivo to bind specifically to a wide spectrum of targets ranging from biological to environmental molecules. They play a vital role in research, diagnostics, sensing, and therapeutic applications. Over the past few decades, advancements have been made to improve the performance of antibodies, specifically in the area of immunosensors. However, there has been an urgent need for alternative high-quality recognition probes that can be produced synthetically in bulk quantity to ensure better reproducibility and lower cost, as well as avoiding the need of using animals in the production process. Aptamers are synthetic nucleic acid single-stranded (ss) DNAs or RNAs that can bind with high affinity and specificity to their targets. They can be generated via in vitro section protocol, known as systematic evolution of ligands by exponential enrichment (SELEX). The advantages of aptamers promoted their successful incorporation in several signal transduction schemes, some of which reached the commercial market for point-of-care and in-field applications. This chapter describes the two types of affinity reagents: antibodies and aptamers, and their methods of production, advantages, and limitations. The focus will be directed at their incorporation in analytical transduction methods and how aptamer molecular size as well as unique conformational change upon target binding has triggered the evolution of new sensing methods.

An Electrochemical Sensor Based on Structure Switching of Dithiol-modified Aptamer for Simple Detection of Ochratoxin A

In this study, we developed an electrochemical sensor for ochratoxin A (OTA) by using an aptamer having a dithiol-based anchor, which exhibited higher stability on a gold electrode than a monothiol-based aptamer because of its two anchors. The sensor was also based on a signal-on scheme that produces a signal current resulting from structure-switching of the aptamer upon interaction with OTA. For simple fabrication of this sensor, the non-covalent interaction of methylene blue with the aptamer was also employed as an electrochemical indicator. In this study, the performance of the sensor, including the dissociation constant of the aptamer-OTA complex, was characterized. The proposed sensor exhibited high reproducibility and enough sensitivity to detect the minimum amount of OTA required for the analysis of real food samples with a limit of detection of 113 pM.

Aptamer-Based Fluorometric Ochratoxin A Assay Based on Photoinduced Electron Transfer

This study describes a novel quencher-free fluorescent method for ochratoxin A (OTA) detection based on the photoinduced electron transfer (PIET) between guanine and fluorophore. In the absence of OTA, carboxyfluorescein (FAM)-labeled aptamer can partly hybridize with the complementary strand of OTA aptamer (OTA-cAPT), which contains four guanines at its 3′-end. As a result, the fluorescence of FAM is quenched due to PIET and stacked guanines. In the presence of OTA, FAM-labeled OTA aptamer can bind specifically to OTA, and thereby the high fluorescence intensity of the dye can be maintained. Under the optimal conditions, the method had a detection limit of 1.3 nM. In addition, the method we proposed is highly sensitive and specific for OTA. Furthermore, the method was proven to be reliable based on its successful application in the detection of OTA in red wine samples. Therefore, this promising, facile, and quencher-free method may be applied to detect other toxins by using other appropriate aptamers.

An aptasensor based on the microscopic enumeration of encoding gold nanoparticles for the detection of C-reactive protein

C-reactive protein (CRP) is a crucial clinical biomarker for inflammatory and cardiovascular diseases. Therefore, the sensitive, selective and convenient detection of CRP is of great significance. Using gold nanoparticles (AuNPs) and combining the specific interaction between an aptamer and CRP, we developed a simple and convenient assay for CRP detection. The aptamer-based probe was fabricated through the hybridization of CRP-aptamer immobilized on magnetic beads (MBs) to a short complementary DNA (cDNA) chain attached to AuNPs to form a MB–Aptamer–AuNP sandwich structure. Upon the addition of CRP, aptamer–cDNA dehybridization occurred due to the strong interaction between CRP and the aptamer, resulting in the release of AuNPs, which were subjected to DFM imaging and subsequently counted using the MATLAB program. The number of AuNPs was therefore positively correlated to the concentration of CRP and a detection limit as low as 2.71 nM was achieved. The current approach could also exclude the disturbance of other proteins, including thrombin, IgG, Lys and BSA. In addition, the concentration of CRP detected was in good agreement with the amount cast in bovine and mouse serum, indicating that the proposed probe is robust and accurate, and it is very promising for practical applications where CRP detection is necessary. The current strategy is also promising for the detection of other proteins where a suitable aptamer is selected.

An aptasensor based on the displacement of encoding AuNPs by analyte molecules was presented. Combined with magnetic separation and DFM imaging, the number of displaced AuNPs was counted, which was correlated to the concentration of the CRP.

Sensitive aptamer-based fluorescene assay for ochratoxin A based on RNase H signal amplification

A new assay for the selective and sensitive aptamer-based fluorescent biosensor for ochratoxin A (OTA) detection is proposed. It consists of a ribonuclease H (RNase H)-assisted cycle response that leads to a significant amplification of the signal, which allow for a low limit of detection (LOD) of 0.08 ng/mL. By using this technique, a high selectivity for OTA against ochratoxin B and aflatoxin B₁ (AFB₁) was noticed. The quantitative determination in real samples has been verified using red wine samples spiked with a series of OTA concentrations (0.4, 4, and 12 ng/mL), and the recoveries ranged from 96.1 to 107.5%. This aptasensor has great practical applications in food industry and moreover, can be extended for the detection of other toxins by replacing the sequence of the recognition aptamer.

Detecting Biothreat Agents: From Current Diagnostics to Developing Sensor Technologies

Although a fundamental understanding of the pathogenicity of most biothreat agents has been elucidated and available treatments have increased substantially over the past decades, they still represent a significant public health threat in this age of (bio)terrorism, indiscriminate warfare, pollution, climate change, unchecked population growth, and globalization. The key step to almost all prevention, protection, prophylaxis, post-exposure treatment, and mitigation of any bioagent is early detection. Here, we review available methods for detecting bioagents including pathogenic bacteria and viruses along with their toxins. An introduction placing this subject in the historical context of previous naturally occurring outbreaks and efforts to weaponize selected agents is first provided along with definitions and relevant considerations. An overview of the detection technologies that find use in this endeavor along with how they provide data or transduce signal within a sensing configuration follows. Current "gold" standards for biothreat detection/diagnostics along with a listing of relevant FDA approved in vitro diagnostic devices is then discussed to provide an overview of the current state of the art. Given the 2014 outbreak of Ebola virus in Western Africa and the recent 2016 spread of Zika virus in the Americas, discussion of what constitutes a public health emergency and how new in vitro diagnostic devices are authorized for emergency use in the U.S. are also included. The majority of the Review is then subdivided around the sensing of bacterial, viral, and toxin biothreats with each including an overview of the major agents in that class, a detailed cross-section of different sensing methods in development based on assay format or analytical technique, and some discussion of related microfluidic lab-on-a-chip/point-of-care devices. Finally, an outlook is given on how this field will develop from the perspective of the biosensing technology itself and the new emerging threats they may face.

Chemical and Biological Sensors for Food-Quality Monitoring and Smart Packaging

The growing interest in food quality and safety requires the development of sensitive and reliable methods of analysis as well as technology for freshness preservation and food quality. This review describes the status of chemical and biological sensors for food monitoring and smart packaging. Sensing designs and their analytical features for measuring freshness markers, allergens, pathogens, adulterants and toxicants are discussed with example of applications. Their potential implementation in smart packaging could facilitate food-status monitoring, reduce food waste, extend shelf-life, and improve overall food quality. However, most sensors are still in the development stage and need significant work before implementation in real-world applications. Issues like sensitivity, selectivity, robustness, and safety of the sensing materials due to potential contact or migration in food need to be established. The current development status of these technologies, along with a discussion of the challenges and opportunities for future research, are discussed.

A test strip for ochratoxin A based on the use of aptamer-modified fluorescence upconversion nanoparticles

An aptamer-based test strip is described for visual and instrumental determination of the mycotoxin ochratoxin A (OTA). It is based on the use of NaYF₄:Yb,Er upconversion nanoparticles (UCNPs) as a label for the aptamer and on the competition between OTA and its complementary sequence for an OTA-specific aptamer. To improve the analytical performance, the optical properties of the UCNPs, the fluidity of the UCNP-aptamer conjugate, and the migration rate on the nitrocellulose membranes were investigated. Under the optimal experimental conditions and by using a 980-nm laser, the relative fluorescence intensity (test line value/control line value) is proportional to the logarithm of the OTA concentration over a range from 5 to 100 ng·mL^-1 (R² = 0.9955). The limit of the detection is 1.86 ng·mL^-1. This aptamer based flow assay can be performed within 15 min and has no serious cross-sensitivity to potentially interfering species. It was successfully applied to the determination of OTA in spiked wheat and beer samples. Graphical abstract An aptamer-based upconversion fluorescent strip based on the use of NaYF₄:Yb,Er nanoparticles was developed for sensitive detection of Ochratoxin A. The limit of the detection was determined as 1.86 ng·mL^-1. The assay can be performed within 15 min, indicating its great potential in point-of-care testing.

Development of a Magnetic Nanoparticles-Based Screen-Printed Electrodes (MNPs-SPEs) Biosensor for the Quantification of Ochratoxin A in Cereal and Feed Samples

A rapid and sensitive electrochemical biosensor based on magnetic nanoparticles and screen-printed electrodes (MNPs-SPEs sensor) was developed for the detection of ochratoxin A (OTA) in cereal and feed samples. Different types of magnetic nanoparticles-based ELISA (MNPs-ELISA) were optimized, and the signal detection, as well as sensitivity, was enhanced by the combined use of screen-printed electrodes (SPEs). Under the optimized conditions, the calibration curve of the MNPs-SPEs sensor was y = 0.3372x + 0.8324 (R² = 0.9805). The linear range of detection and the detection limit were 0.01–0.82 ng/mL and 0.007 ng/mL, respectively. In addition, 50% inhibition (IC50) was detectable at 0.10 ng/mL. The limit of detection (LOD) of this MNPs-SPEs sensor in cereal and feed samples was 0.28 μg/kg. The recovery rates in spiked samples were between 78.7% and 113.5%, and the relative standard deviations (RSDs) were 3.6–9.8%, with the coefficient of variation lower than 15%. Parallel analysis of commercial samples (corn, wheat, and feedstuff) showed a good correlation between MNPs-SPEs sensor and liquid chromatography tandem mass spectrometry (LC/MS-MS). This new method provides a rapid, highly sensitive, and less time-consuming method to determine levels of ochratoxin A in cereal and feedstuff samples.

Simultaneous determination of trace Aflatoxin B1 and Ochratoxin A by aptamer-based microchip capillary electrophoresis in food samples

An aptamer-based microchip capillary electrophoresis coupled with laser induced fluorescence (MCE-LIF) detection method for fast determination of Aflatoxin B₁ (AFB₁) and Ochratoxin A (OTA) was developed. Aptamers that are specific to these two mycotoxins were first hybridized with their aptamer complementary oligonucleotides. The double strand DNA that comes in contact with mycotoxin-containing environment would be unwound into separate aptamer-mycotoxin complex and aptamer complementary single strand. Different types of oligonucleotides can be separated in MCE and detected under the aid of fluorescent dye SYBR gold in LIF detection unit. Under the optimal conditions, on-chip aptamer-mycotoxin conjugates analysis was achieved within 3 min with extremely low LODs (0.026 ng/mL for AFB₁ and 0.021 ng/mL for OTA). Specificity study indicated that other major mycotoxins would not cross-react with these two aptamers, demonstrating the good selectivity of the proposed method. Quantification of trace AFB₁ and OTA in real food samples was carried out and satisfactory recoveries were obtained. It is demonstrated that this method is fast, facile and specific for Simultaneous determination of trace AFB₁ and OTA from foodstuffs.

A Label-Free Aptasensor for Ochratoxin a Detection Based on the Structure Switch of Aptamer

A label-free sensing platform is developed based on switching the structure of aptamer for highly sensitive and selective fluorescence detection of ochratoxin A (OTA). OTA induces the structure of aptamer, transforms into G-quadruplex and produces strong fluorescence in the presence of zinc(II)-protoporphyrin IX probe due to the specific bind to G-quadruplex. The simple method exhibits high sensitivity towards OTA with a detection limit of 0.03 nM and excellent selectivity over other mycotoxins. In addition, the successful detection of OTA in real samples represents a promising application in food safety.

Label-Free G-Quadruplex Aptamer Fluorescence Assay for Ochratoxin A Using a Thioflavin T Probe

Ochratoxin A (OTA) is one of the most common mycotoxins contaminating feed and foodstuffs. Therefore, a great deal of concern is associated with AFB1 toxicity. In this work, a fast and sensitive fluorescence aptamer biosensor has been proposed for the OTA assay. In the absence of OTA, the OTA aptamer can form a G-quadruplex structure with thioflavin T (ThT) dye, which results in increased fluorescence. After joining OTA, OTA aptamer combines with OTA and the G-quadruplex can be formed. Only faint fluorescence was finally observed when ThT weakly reacts with the quadruplex. Through this test method, the entire reaction and analysis process of OTA can be completed in 10 min. Under optimal experimental conditions (600 nM OTA-APT, 7 μM ThT, and 3 min incubation time), this proposed assay has a good limit of detection (LOD) of 0.4 ng/mL and shows a good linear relationship within the range of 1.2⁻200 ng/mL under the best experimental conditions. This method has a high specificity for OTA relative to Ochratoxin B (23%) and Aflatoxin B₁ (13%). In addition, the quantitative determination of this method in real samples has been validated using a sample of red wine supplemented with a range of OTA concentrations (1.2 ng/mL, 12 ng/mL, and 40 ng/mL) with recoveries of 96.5% to 107%.

Designed Strategies for Fluorescence-Based Biosensors for the Detection of Mycotoxins

Small molecule toxins such as mycotoxins with low molecular weight are the most widely studied biological toxins. These biological toxins are responsible for food poisoning and have the potential to be used as biological warfare agents at the toxic dose. Due to the poisonous nature of mycotoxins, effective analysis techniques for quantifying their toxicity are indispensable. In this context, biosensors have been emerged as a powerful tool to monitors toxins at extremely low level. Recently, biosensors based on fluorescence detection have attained special interest with the incorporation of nanomaterials. This review paper will focus on the development of fluorescence-based biosensors for mycotoxin detection, with particular emphasis on their design as well as properties such as sensitivity and specificity. A number of these fluorescent biosensors have shown promising results in food samples for the detection of mycotoxins, suggesting their future potential for food applications.