Cross-linked succinyl chitosan as an adsorbent for the removal of Methylene Blue from aqueous solution

Methylene blue sorption performance of lignocellulosic peach kernel shells modified with cellulose derivative chitosan as a new bioadsorbent

In this study, adsorption isotherms (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and thermodynamic properties of cationic methylene blue (MB) dye adsorption onto chitosan-coated peach kernel shell waste (CTS-PKSh) from wastewater were investigated. CTS was cross-linked with citric acid (CA) and glutaraldehyde (GA). The adsorbents were characterized by FE-SEM/EDS, FTIR, and particle size distribution. MB adsorption behavior onto the biosorbents was investigated concerning parameters such as adsorbent dosage (0.8-8 g/L), time (0-540 min), pH (3-10), initial dye concentration (50-700 mg/L), and temperature (25-55 °C). The Langmiur qmax and experimentally qe MB adsorption capacities of the new adsorbents were found to be 227.27 and 201 mg/g for CA cross-linked CTS-PKSh (CA@CTS-PKSh) and 111.12 and 96.5 mg/g for GA cross-linked CTS-PKSh (GA@CTS-PKSh), respectively. The results of thermodynamic analysis showed that adsorption was feasible, exothermic, and spontaneous. According to adsorption and recyclability results, CA@CTS-PKSh was more effective for MB removal at a 2 g/L adsorbent dose for an initial dye concentration of 100 mg/L, 25 ± 1 °C, contact time 60 min, and pH 7.

A novel hydrogel composite of chitosan-phytic acid complex with PAAm: Characterization and adsorptive properties for UO22+and methylene blue

The composite of a polyelectrolyte combination of chitosan and phytic acid (CsPa) and its entrapped form in polyacrylamide (PAAmCsPa) were synthesized. The composites were characterized by a number of methods including ATR-FTIR, SEM-EDX, XRD and XPS. The adsorptive properties of CsPa and PAAmCsPa were analyzed and modelled for UO22+ and methylene blue (MB+). The results showed that the composites exhibited physico-chemical properties that were both inherited from the components as well as unique to them. The isotherms of UO22+ and MB+ were L-type Giles isotherms. The adsorption kinetics followed the pseudo-second-order model, in contrast to the Langmuir model, which predicts first-order kinetics for both species. According to the Weber-Morris model, the nature of the adsorption process was ion exchange and/or complex formation for both composites and ions. The thermodynamics showed that the adsorption process was endothermic (ΔH > 0), with increasing entropy (ΔS > 0) and spontaneous (ΔG < 0). The reusability tests of the composites for UO22+ adsorption showed that the composites were substantially reusable for 6 cycles. The composites were selective for UO22+ over MB+ ions, and UO22+ adsorption increased significantly when MB+ adsorbed composites were used. Reproducible measurements demonstrating the storability of the composites were obtained over a period of approximately one year.

Synthesis and characterization of Alg/Gel/n-HAP/MNPs porous nanocomposite adsorbent for efficient water conservancy and removal of methylene blue in aqueous environments: Kinetic modeling and artificial neural network predictions

In this study, a new porous nanocomposite adsorbent for water conservancy was synthesized using the freeze-drying technique to adsorb a cationic dye (Methylene Blue) in an aqueous environment. The nanocomposite adsorbent was synthesized using natural polymers, gelatin, and sodium alginate, and hydroxyapatite and magnetic iron oxide nanoparticles was incorporated into the polymer network to improve mechanical properties and increase the surface-to-volume ratio. To confirm the structure and morphology of the sample, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscope (SEM) techniques were employed. In addition, the magnetic properties of the synthesis of MNPs and porous nanocomposite were determined using value stream mapping (VSM) and dynamic light scattering (DLS). The adsorption of Methylene Blue (MB) was studied as a function of effective physical and variable parameters, such as time, temperature, pH, and initial concentration. The synthesized porous nanocomposite adsorbent exhibited a high adsorption capacity of 473.2 mg g-1 and followed pseudo-second-order kinetics. Additionally, the maximum adsorption capacity was observed at an initial concentration of 534.9 mg g-1. The adsorbent was also sensitive to temperature changes and was well-described thermodynamically and isothermally by the Freundlich isotherm model. Two artificial neural networks (ANNs) were also developed to investigate the properties of the synthesized nanocomposites. In the first ANN, the properties of the nanocomposites, including pore size, porosity, compressive strength, and elastic modulus, were predicted based on the variations in the weight percentages of gelatin and hydroxyapatite. In the second ANN, the effects of changes in temperature and initial concentration on the adsorption of MB by the synthesized nanocomposite samples were predicted. The ANNs' predictions indicated that increasing the weight percentage of hydroxyapatite nanoparticles and gelatin enhances the physical, mechanical, and adsorption performance of the synthesized porous nanocomposites. The best results were achieved for the sample containing 40 wt % of gelatin and 30 wt % of hydroxyapatite nanoparticles. Furthermore, the ANN models demonstrated that increasing the temperature and initial concentration resulted in an increase in the amount of MB adsorbed.

Investigating the Sulfonated Chitosan/Polyvinylidene Fluoride-Based Proton Exchange Membrane with fSiO2 as Filler in Microbial Fuel Cells

Chitosan (CS), a promising potential biopolymer with exquisite biocompatibility, economic viability, hydrophilicity, and chemical modifications, has drawn interest as an alternative material for proton exchange membrane (PEM) fabrication. However, CS in its original form exhibited low proton conductivity and mechanical stability, restricting its usage in PEM development. In this work, chitosan was functionalized (sulfonic acid (-SO3H) groups)) to enhance proton conductivity. The sulfonated chitosan (sCS) was blended with polyvinylidene fluoride (PVDF) polymer, along with the incorporation of functionalized SiO2 (-OH groups), for fabricating chitosan-based composite proton exchange membranes to enhance microbial fuel cell (MFC) performances. The results show that adding functionalized inorganic fillers (fSiO2) into the membrane enhances the mechanical, thermal, and anti-biofouling behavior. From the results, the PVDF/sCS/fSiO2 composite membrane exhibited enhanced proton conductivity 1.0644 × 10-2 S cm-1 at room temperature and increased IEC and mechanical and chemical stability. Furthermore, this study presents a revolutionary way to generate environmentally friendly natural polymer-based membrane materials for developing PEM candidates for enhanced MFC performances in generating bioelectricity and wastewater treatment.

Modified porous starch for enhanced properties: Synthesis, characterization and applications

Native starches have low water solubility at room temperature and poor stability, which demand modifications to overcome. Porous starch as a modified one shows enhanced adsorptive efficiency and solubility compared with its native starch. In contrast, some inherent disadvantages exist, such as weak mechanical strength and low thermal resistance. Fortunately, modified porous starches have been developed to perform well in adsorption capacity and stability. Modified porous starch can be prepared by esterification, crosslinking, oxidation and multiple modifications to the porous starch. The characterization of modified porous starch can be achieved through various analytical techniques. Modified porous starch can be utilized as highly efficient adsorbents and encapsulants for various compounds and applied in various fields. This review dealt with the progress in the preparation, structural characterization and application of modified porous starch. The objective is to provide a reference for its development, utilization, and future research directions.

Hungarian and Indonesian rice husk as bioadsorbents for binary biosorption of cationic dyes from aqueous solutions: A factorial design analysis

The wastewater of the dye industry can be characterized by a complex chemical composition and consists of numerous dyes. Bioadsorbents are increasingly applied for the biosorption of dyes because they are inexpensive and environmentally friendly. Rice husk (RH) is a potential agricultural waste that can be converted into a bioadsorbents for the biosorption of cationic dyes. Herein, the removal of methylene blue (MB) and basic red 9 (BR9) dyes by Hungarian rice husk (HRH) and Indonesian rice husk (IRH) using binary biosorption was investigated. Adsorbents were characterized by zeta potential, Fourier-transform infrared spectroscopy, and scanning electron microscopy. Batch biosorption evaluated the influence of different variables, including pH, adsorbent dose, contact time, and initial concentrations. Several factors that influence the biosorption of MB and BR9 onto rice husk were assessed using main effect, Pareto charts, normal probability plots, and interaction effect in a factorial design. The optimum contact time was 60 min. Isotherm and kinetic models of MB and BR9 in binary biosorption fitted to the Brunauer-Emmett-Teller multilayer and the Elovich equation based on correlation coefficients and nonlinear chi-square. Results showed that the biosorption capacity of HRH was 10.4 mg/g for MB and 10 mg/g for BR9; values for IRH were 9.3 mg/g and 9.6 mg/g, respectively. Therefore, HRH and IRH were found to be effective adsorbents for removing MB and BR9 via binary biosorption.

Effects of activated earth, activated alumina, and chitosan adsorption processes on thermal and rheological and chemical characteristics of menhaden oil

The objective of this study was the effectiveness of using activated earth, activated alumina, and/or chitosan, either separately or in combination, as adsorbents to remove free fatty acids (FFA) and peroxides from unpurified menhaden oil (MO). Thermal and rheological properties of MO were also evaluated. Five different combinations of absorbents were used to purify MO: Processes 1-3 involved purifications of MO by 5% chitosan (wt/wt of oil), 5% activated earth, and 5% activated alumina, respectively, process 4 involved MO purification with a combination of 6.5% chitosan, 3.5% activated earth, and 5% activated alumina, and process 5 involved MO purification process with a combination of adsorbents of 9% chitosan, 1% activated earth, and 5% activated alumina. All the adsorption processes were conducted at 25°C. Purified MO and MO were evaluated for their fatty acid profile, FFA, peroxide value (PV), moisture content (MC), minerals, and color. Triplicate experiments were conducted, and data were statistically analyzed using α = 0.05. Processes 4 and 5 were effective in reducing PV, FFA, and MC in MO. Thermal properties indicated processes 4 and 5 produced purer MO than processes 1-3. All the oil samples became less viscous, and the flow behavior index of MO was close to 1 after the adsorption processes. This study demonstrated that adsorption processes that include chitosan, activated earth, and activated alumina could effectively improve MO quality.

Removal of Methylene Blue and Congo Red Using a Chitosan-Graphene Oxide-Electrosprayed Functionalized Polymeric Nanofiber Membrane

Untreated textile effluent may contain toxic organic pollutants that can have negative impacts on the ecosystem. Among the harmful chemicals present in dyeing wastewater, there are two frequently used organic dyes: methylene blue (cationic) and congo red (anionic). The current study presents investigations on a novel two-tier nanocomposite membrane, i.e., a top layer formed of electrosprayed chitosan-graphene oxide and a bottom layer consisting of an ethylene diamine functionalized polyacrylonitrile electrospun nanofiber for the simultaneous removal of the congo red and methylene blue dyes. The fabricated nanocomposite was characterized using FT-IR spectroscopy, scanning electron microscopy, UV-visible spectroscopy, and Drop Shape Analyzer. Isotherm modeling was used to determine the efficiency of dye adsorption for the electrosprayed nanocomposite membrane and the confirmed maximum adsorptive capacities of 182.5 mg/g for congo red and 219.3 mg/g for methylene blue, which fits with the Langmuir isotherm model, suggesting uniform single-layer adsorption. It was also discovered that the adsorbent preferred an acidic pH level for the removal of congo red and a basic pH level for the removal of methylene blue. The gained results can be a first step for the development of new wastewater cleaning techniques.

Adsorption Performance of Methylene Blue by KOH/FeCl3 Modified Biochar/Alginate Composite Beads Derived from Agricultural Waste

In this study, high-performance modified biochar/alginate composite bead (MCB/ALG) adsorbents were prepared from recycled agricultural waste corncobs by a high-temperature pyrolysis and KOH/FeCl3 activation process. The prepared MCB/ALG beads were tested for the adsorption of methylene blue (MB) dye from wastewater. A variety of analytical methods, such as SEM, BET, FTIR and XRD, were used to investigate the structure and properties of the as-prepared adsorbents. The effects of solution pH, time, initial MB concentration and adsorption temperature on the adsorption performance of MCB/ALG beads were discussed in detail. The results showed that the adsorption equilibrium of MB dye was consistent with the Langmuir isothermal model and the pseudo-second-order kinetic model. The maximum adsorption capacity of MCB/ALG−1 could reach 1373.49 mg/g at 303 K. The thermodynamic studies implied endothermic and spontaneous properties of the adsorption system. This high adsorption performance of MCB/ALG was mainly attributed to pore filling, hydrogen bonding and electrostatic interactions. The regeneration experiments showed that the removal rate of MB could still reach 85% even after five cycles of experiments, indicating that MCB/ALG had good reusability and stability. These results suggested that a win-win strategy of applying agricultural waste to water remediation was feasible.

Preparation of Breadfruit Leaf Biochar for the Application of Congo Red Dye Removal from Aqueous Solution and Optimization of Factors by RSM-BBD

In this work, biochar produced from breadfruit leaves was utilized to remove the toxic Congo red dye. XRD, FTIR, and FESEM-EDX were implemented to characterize the biochar. Response surface methodology (RSM) and the Box-Behnken design (BBD) techniques were used to evaluate Congo red’s optimum adsorption efficiency. The adsorption of Congo red was studied by varying dye concentrations (5–50 mg/L), times (30–240 min), pH (6–9), and dosages (0.5–2 g/100 mL). X-ray diffractometer results show that the structure of biochar is amorphous. The biochar exhibited unbounded OH, aliphatic CH group, and C=O stretch, as shown by the band peaks at 3340 cm−1, 2924 cm−1, and 1625 cm−1 intensities. RSM-BBD design results showed maximum removal efficiency of 99.96% for Congo red at pH 6.37, dye concentration 45 mg/L, time 105 min, and dosage 1.92 g, respectively. The adsorption of Congo red by biochar was successfully modeled using the Langmuir model and pseudo-second-order model. The biochar produced from breadfruit leaves exhibited a high adsorption capacity of 17.81 mg/g for Congo red adsorption. It suggests that the adsorption is both homogenous monolayer and physicochemical.

Preparation of a novel glucose oxidase-N-succinyl chitosan nanospheres and its antifungal mechanism of action against Colletotrichum gloeosporioides

In this work, a new glucose oxidase-N-succinyl chitosan (GOD-NSCS) nanospheres was prepared through the immobilization of glucose oxidase (GOD) on N-succinyl chitosan (NSCS) nanospheres. Compared to the free GOD, GOD-NSCS nanospheres demonstrated the excellent anti-Colletotrichum gloeosporioides activity with the EC₅₀ values of 211.2 and 10.7 μg/mL against mycelial growth and spores germination. The computational biology analysis demonstrated that the substrate presented the similar binding free energy with GOD-NSCS nanospheres (-27.64 kcal/mol) compared with the free GOD (-24.04 kcal/mol), indicating that GOD-NSCS nanospheres had the same oxidation efficiency and produced more H₂O₂. Moreover, the enzyme activity stability of GOD-NSCS nanospheres could be prolonged to 10 d. The cell membrane was destructed by the treatment of H₂O₂ produced by GOD, leading to the cell death. In vivo test, GOD-NSCS nanospheres treatment significantly prolonged the preservation period of mangoes 2-fold. Collectively, these results suggested that GOD-NSCS nanospheres suppresses anthracnose in postharvest mangoes by inhibiting the growth of C. gloeosporioides and might become a potential natural preservative for fruits and vegetables.

Post-treatment of matured landfill leachate: Synthesis and evaluation of chitosan biomaterial based derivatives as adsorbents

Matured landfill leachate is complex in nature, hence, a single conventional treatment unit is insufficient to remove the contaminants of the leachate to achieve the discharge standards. Furthermore, high levels of organic matter, colour compounds, and iron-based materials form a dark black/brown colour in leachate which is not removed by the biological treatment units. Hence, an Anoxic-Oxic Membrane Bioreactor coupled with a tertiary adsorption unit composed of crosslinked-protonated chitosan was tested for effective removal of the colour of the permeate. Several operational parameters such a pH, contact time, and adsorbent dosage on the adsorptive removal of colour were quantified using sorption-desorption experiments. Furthermore, the biosorbent was characterized using FTIR, SEM, XRD, BET-specific surface area, and pH_ZPC. Response Surface analysis confirmed the optimization of operational parameters conducted through traditional batch experiments. Langmuir isotherm model fitted with equilibrium data (R² = 0.979) indicating a monolayer homogeneous adsorption. Kinetic data followed the Pseudo-Second-Order model (R² = 0.9861), showing that the adsorbent material has abundant active sites. The percentage removal values show that the colour removal increases with time of contact and dosage of adsorbent, but removal is mainly influenced by the solution pH levels. The experimental results manifested a colour removal efficiency of 96 ± 3.8% obtained at optimum conditions (pH = 2, adsorbent dosage = 20 g/L, contact time = 48 h) along with an adsorption capacity of 123.8 Pt-Co/g suggesting that the studied adsorbent can be used as an environmentally friendly biosorbent in a tertiary unit for colour removal in a treatment system which is used to treat matured landfill leachate.

Chitosan beads coated with almond and walnut shells for the adsorption of gatifloxacin antibiotic compound from aqueous solutions

In the present study, chitosan (C), walnut (W), and almond shell (A) powder adsorbent (in different combinations as almond shells:walnut:chitosan 2:1:1 (AWC), chitosan:almond shell:walnut 2:1:1 (CAW), and walnut:almond shells:chitosan 2:1:1 (WAC)) powder were combined in different ratios to produce low-cost composite adsorbent beads for the removal of antibiotics gatifloxacin (GAT) from synthetic wastewater. The beads were characterized by a scanning electron microscope, Fourier transform infrared spectrum spectrophotometer, and energy-dispersive X-ray spectroscopy. The batch adsorption approach was employed to remove the antibiotic from the water. Moreover, isotherm and kinetics were conducted to illustrate the adsorption mechanism. Parameters like the effect of the adsorbent's dosage, pH, initial concentration, and contact time on antibiotic adsorption were evaluated. Adsorption percentage increased slightly with the increase in adsorbent dosage. The optimum pH for GAT adsorption on beads was 5-7. In addition, adsorption increased with initial antibiotic concentration and time rise. The adsorption isotherm data were successfully fitted to Langmuir isotherm for AWC and CAW beads, while WAC beads followed the Freundlich isotherm. The highest adsorption was attained at pH 5 on CAW beads and pH 7 on AWC and WAC beads. The optimal contact time for equilibrium studies was 120 min for all types of beads. The adsorption isotherm data in AWC beads fit well with the Langmuir model and Freundlich adsorption for CAW and WAC beads. The rate of adsorption on beads follows Lagergren pseudo-second-order kinetics. The results indicate that prepared combination beads can be used to remove antibiotics from wastewater.

Chitosan-Graphene Oxide Dip-Coated Polyacrylonitrile-Ethylenediamine Electrospun Nanofiber Membrane for Removal of the Dye Stuffs Methylene Blue and Congo Red

Textile wastewater accommodates many toxic organic contaminants that could potentially threaten the ecosystem if left untreated. Methylene blue is a toxic, non-biodegradable, cationic dye that is reportedly observed in significant amounts in the textile effluent stream as it is widely used to dye silk and cotton fabrics. Congo red is a carcinogenic anionic dye commonly used in the textile industry. This study reports an investigation of methylene blue and Congo red removal using a chitosan-graphene oxide dip-coated electrospun nanofiber membrane. The fabricated nanocomposite was characterized using Scanning Electron Microscopy (SEM), FT-IR Spectroscopy, Raman Spectroscopy, UV-vis Spectroscopy, Drop Shape Analyzer, and X-ray Diffraction. The isotherm modeling confirmed a maximum adsorptive capacity of 201 mg/g for methylene blue and 152 mg/g for Congo red, which were well fitted with a Langmuir isotherm model indicating homogenous monolayer adsorption.

Removal of Methyl Violet from Aqueous Solution by Adsorption onto Halloysite Nanoclay: Experiment and Theory

Methyl Violet (MV) was removed from aqueous solutions by adsorption onto halloysite nanoclay (HNC) employing equilibrium, kinetics, thermodynamic data, molecular modellingR (MD), and Monte Carlo (MC) simulations. The chosen experimental variables were pH, temperature, starting MV concentration, contact time, and adsorbent dosage. The adsorption rate was determined to increase with increasing contact time, initial dye concentration, pH, and temperature. The Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich (D-R) isotherms were utilized to determine the adsorption capacity of HNC. The Langmuir equation matched equilibrium data better than the other models, whereas the pseudo-second-order model better described kinetic data, and thermodynamic analyses revealed that the adsorption process was spontaneous, endothermic, and physisorption-based. This study focused on two distinct molecular mechanics-based theoretical approaches (MC and MD). These techniques enabled a molecular comprehension of the interaction between the MV molecule and the halloysite surface. Theoretical results were consistent with experimental findings. The outcomes revealed that HNC is an excellent dye adsorbent for industrial effluents.

Magnetic cross-linked chitosan for efficient removing anionic and cationic dyes from aqueous solution

Herein, a novel magnetic cross-linked chitosan CS-BA@Fe₃O₄ was rationally synthesized by cross-linked with epichlorohydrin and coated with Fe₃O₄ to the acylated chitosan, which was prepared by the reaction of chitosan with benzenetricarboxylic anhydride. The as-obtained absorbent was characterized by FTIR, XRD, VSM, TGA, TEM, BET, SEM and EDS. The results showed that the maximum adsorption capacities of CR and CV were 471.46 ± 16.97 mg/g and 515.91 ± 25.12 mg/g at 318.15 K, respectively. The main adsorption mechanisms were H-bonding and electrostatic interaction. The kinetic data were in good agreement with the pseudo-second-order model and closed to adsorption equilibrium at 30 min. Thermodynamic studies showed that the adsorption on CS-BA@Fe₃O₄ were spontaneous and endothermic. More importantly, the adsorbent exhibited excellent regeneration properties after 6 cycles and remarkable stability under harsh environments including strong acid, strong alkali, multi-salt and mixed dyes conditions. Therefore, abundant efforts revealed a broad application prospect of CS-BA@Fe₃O₄ in water remediation.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

Adsorption of toxic dye Eosin Y from aqueous solution by clay/carbon composite derived from spent bleaching earth

The environmentally friendly clay/carbon composite (SBE/C) was prepared by one-step pyrolysis under N₂ atmosphere at 700°C of spent bleaching earth (SBE) from the industrial waste of the refined oil industry. SBE/C was tested to remove anionic dye Eosin Y from aqueous water. The results revealed that SBE/C had larger specific surface area than SBE, and the equilibrium adsorption capacity of SBE/C (11.15 mg/g) was about 3 times than that of SBE (4.04 mg/g). The adsorption process was found to be exothermic and spontaneous. The adsorption capacity of SBE/C was independent on pH (5-12), and exhibits satisfactorily recyclable performance. Combined with characterization analysis, the adsorption mechanism likely includes electrostatic interaction, hydrogen bonding, hydrophobic interaction, halogen bonding, and π-π interaction. Overall, this exploration of SBE/C might open a window to the design of an efficient and low-cost adsorbent for Eosin Y dye elimination from wastewater. PRACTITIONER POINTS: The resource utilization of industrial waste SBE was achieved. SBE/C was synthesized and tested to adsorb Eosin Y for the first time. SBE/C had characteristics with porous structure and large surface area. pH had little effect on adsorption capacity of SBE/C for Eosin Y. SBE/C exhibited potential for dye elimination from wastewater.

Zwitterion composite chitosan-epichlorohydrin/zeolite for adsorption of methylene blue and reactive red 120 dyes

In this research, an attempt to develop zwitterion composite adsorbent is conducted by modifying chitosan (CHS) with a covalent cross-linker (epichlorohydrin, ECH) and an aluminosilicate mineral (zeolite, ZL). The zwitterion composite adsorbent of chitosan-epichlorohydrin/zeolite (CHS-ECH/ZL) is performed multifunctional tasks by removing two structurally different cationic (methylene blue dye, MB), and anionic (reactive red 120 dye, RR120) dyes from aqueous solutions. The surface property, crystallinity, morphology, functionality, and charge of the CHS-ECH/ZL are analyzed using BET, XRD, SEM, FTIR, and pH_pzc, analyses, respectively. The influence of pertinent parameters namely CHS-ECH/ZL dosage (0.02-0.5 g), solution pH (4-10), temperature (303-323K), initial dye concentration (30-400 mg/L), and contact time (0-600 min) on the MB and RR120 removal are tested. The research findings revealed that the adsorption isotherm at equilibrium well explained in according to the Freundlich isotherm model, and the recorded adsorption capacities of CHS-ECH/ZL are 156.1 and 284.2 mg/g for MB and RR120 respectively at 30 °C. The mechanism of MB and RR120 adsorption onto the CHS-ECH/ZL indicates various types of interactions namely, electrostatic interaction, hydrogen bonding, and Yoshida H-bonding in addition to n-π interaction. Overall, this research introduces CHS-ECH/ZL composite as an eco-friendly zwitterion adsorbent with good applicability towards the two structurally different cationic and anionic dyes from aqueous environment.

Adsorption of Methylene Blue in Water onto Activated Carbon by Surfactant Modification

In this paper, the enhanced adsorption of methylene blue (MB) dye ion on the activated carbon (AC) modified by three surfactants in aqueous solution was researched. Anionic surfactants—sodium lauryl sulfate (SLS) and sodium dodecyl sulfonate (SDS)—and cationic surfactant—hexadecyl trimethyl ammonium bromide (CTAB)—were used for the modification of AC. This work showed that the adsorption performance of cationic dye by activated carbon modified by anionic surfactants (SLS) was significantly improved, whereas the adsorption performance of cationic dye by activated carbon modified by cationic surfactant (CTAB) was reduced. In addition, the effects of initial MB concentration, AC dosage, pH, reaction time, temperature, real water samples, and additive salts on the adsorption were studied. When Na+, K+, Ca2+, NH4+, and Mg2+ were present in the MB dye solution, the effect of these cations was negligible on the adsorption (<5%). The presence of NO2- improved the adsorption performance significantly, whereas the removal rate of MB was reduced in the presence of competitive cation (Fe2+). It was found that the isotherm data had a good correlation with the Langmuir isotherm through analyzing the experimental data by various models. The dynamics of adsorption were better described by the pseudo-second-order model and the adsorption process was endothermic and spontaneous. The results showed that AC modified by anionic surfactant was effective for the adsorption of MB dye in both modeling water and real water.

A multifunctional gelatine-quaternary ammonium copolymer: An efficient material for reducing dye emission in leather tanning process by superior anionic dye adsorption

Leather wastewater is one of the most polluting industrial emissions. The efficiency of wastewater remediation is limited by its complex composition. Herein, a novel strategy for designing modified gelatine with higher degree of quaternization (MG-2) is presented. The higher degree of quaternization allows sufficient adsorption of dyes in the tanning process. It is an in situ, environmentally friendly, and innovative strategy to limit dye emissions and can circumvent the subsequent waste management. Dyes such as Direct Purple N and Acid Black 24 could be adsorbed completely within 5 min by the MG-2 film formed from MG-2 solution. In addition, a remarkable efficiency in removing Acid Red 73, Golden Orange G, and Acid Orange II (>96.1% removal rates) was achieved within 30 min. The adsorption equilibrium data suggested that the adsorption capacity was positively correlated to the concentration of MG-2. When Acid Orange II and MG-2 were used in the industrial re-tanning process, the residual dye concentration in wastewater was only 23.1 mg L^-1, indicating that MG-2 is a promising re-tanning agent for adsorbing dyes in the leather tanning process.

Removal of copper(II) using deacetylated konjac glucomannan conjugated soy protein isolate

In this study, an environmentally friendly biosorbent deacetylated konjac glucomannan conjugated soy protein isolate (abbreviated as DKGM-C-SPI) was prepared for Cu(2+) ions removal from aqueous solution. Scanning electron microscopy, Fourier transform infrared spectroscopy and zeta potential analysis revealed successful conjugation of soy protein isolate (SPI) onto deacetylated konjac glucomannan (DKGM) matrix. A comparative adsorption performance of DKGM-C-SPI and DKGM was tested to remove Cu(2+) ions from aqueous solution. DKGM-C-SPI showed the desired adsorption performance for Cu(2+) ions. The adsorption equilibrium of DKGM-C-SPI was achieved within 30 min. The adsorption behavior of DKGM-C-SPI followed a pseudo-second-order reaction model. The maximum Cu(2+) ion adsorption capacities obtained from the Langmuir isotherms fit were shown to be 62.50 mg g(-1) for DKGM-C-SPI and 12.23 mg g(-1) for DKGM. This impressive increase about 5 times in Cu(2+) ion adsorption capacity is attributed to the strong Cu(2+) ion chelating ability of the soy protein isolate (SPI) on the DKGM matrix. These results confirm that the DKGM-C-SPI biosorbent has a potential for Cu(2+) ion extraction from wastewater.

Facile synthesis of methyl propylaminopropanoate functionalized magnetic nanoparticles for removal of acid red 114 from aqueous solution

The removal of AR-114 from aqueous solution by novel nano-adsorbent Fe₃O₄@SiO₂–MPAP through hydrogen bonding interactions.

Adsorption of Methylene Blue, Bromophenol Blue, and Coomassie Brilliant Blue by α-chitin nanoparticles

Expelling of dyestuff into water resource system causes major thread to the environment. Adsorption is the cost effective and potential method to remove the dyes from the effluents. Therefore, an attempt was made to study the adsorption of dyestuff (Methylene Blue (MB), Bromophenol Blue (BPB) and Coomassie Brilliant Blue (CBB)) by α-chitin nanoparticles (CNP) prepared from Penaeus monodon (Fabricius, 1798) shell waste. On contrary to the most recognizable adsorption studies using chitin, this is the first study using unique nanoparticles of ⩽50 nm used for the dye adsorption process. The results showed that the adsorption process increased with increase in the concentration of CNP, contact time and temperature with the dyestuff, whereas the adsorption process decreased with increase in the initial dye concentration and strong acidic pH. The results from Fourier transform infrared (FTIR) spectroscopy confirmed that the interaction between dyestuff and CNP involved physical adsorption. The adsorption process obeys Langmuir isotherm (R (2) values were 0.992, 0.999 and 0.992 for MB, BPB and CBB, and RL value lies between 0 and 1 for all the three dyes) and pseudo second order kinetics (R (2) values were 0.996, 0.999 and 0.996 for MB, BPB and CBB) more effectively. The isotherm and kinetic models confirmed that CNP can be used as a suitable adsorbent material for the removal of dyestuff from effluents.

Facile fabrication of magnetic carboxymethyl starch/poly(vinyl alcohol) composite gel for methylene blue removal

This study presents a simple method to fabricate magnetic carboxymethyl starch/poly(vinyl alcohol) (mCMS/PVA) composite gel. The obtained mCMS/PVA was characterized by Fourier transform infrared (FTIR) spectra, vibrating-sample magnetometer (VSM) and scanning electron microscopy (SEM) measurements. The application of mCMS/PVA as an adsorbent for removal of cationic methylene blue (MB) dye from water was investigated. Benefiting from the combined merits of carboxymethyl starch and magnetic gel, the mCMS/PVA simultaneously exhibited excellent adsorption property toward MB and convenient magnetic separation capability. The effects of initial dye concentration, contact time, pH and ionic strength on the adsorption performance of mCMS/PVA adsorbent were investigated systematically. The adsorption process of mCMS/PVA for MB fitted pseudo-second-order model and Freundlich isotherm. Moreover, desorption experiments revealed that the mCMS/PVA adsorbent could be well regenerated in ethanol solution without obvious compromise of removal efficiency even after eight cycles of desorption/adsorption. Considering the facile fabrication process and robust adsorption performance, the mCMS/PVA composite gel has great potential as a low cost adsorbent for environmental decontamination.

Modification of porous starch for the adsorption of heavy metal ions from aqueous solution

Porous starch xanthate (PSX) and porous starch citrate (PSC) were prepared in anticipation of the attached xanthate and carboxylate groups respectively forming chelation and electrostatic interactions with heavy metal ions in the subsequent adsorption process. The lead(II) ion was selected as the model metal and its adsorption by PSX and PSC was characterized. The adsorption capacity was highly dependent on the carbon disulfide/starch and citric acid/starch mole ratios used during preparation. The adsorption behaviors of lead(II) ion on PSXs and PSCs fit both the pseudo-second-order kinetic model and the Langmuir isotherm model. The maximum adsorption capacity from the Langmuir isotherm equation reached 109.1 and 57.6 mg/g for PSX and PSC when preparation conditions were optimized, and the adsorption times were just 20 and 60 min, respectively. PSX and PSC may be used as effective adsorbents for removal of heavy metals from contaminated liquid.

Efficient removal of lead (II) ions and methylene blue from aqueous solution using chitosan/Fe-hydroxyapatite nanocomposite beads

Chitosan is a well-known sorbent and effective in the uptake of anionic or reactive dyes, but it has deficiency in adsorption of basic dyes. In this work, chitosan/Fe-substituted hydroxyapatite composite beads were prepared in a different ratio via embedding of hydroxyapatite into chitosan solution for removal of basic dye and heavy metal from aqueous solution. The composite beads were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy in order to reveal their composition and surface morphology. In this particular study, methylene blue (MB) and lead (Pb (II)) ions were selected as representatives of dye and a heavy metal, respectively. The various experimental conditions affecting dye adsorption were explored to achieve maximum adsorption capacity. Moreover, the kinetic, thermodynamic and adsorption isotherm models were employed for the description of the heavy metal and dye adsorption processes. The results indicated that the prepared hydrogel is an efficient adsorbent for the aforementioned dye and metal concomitant with the ability of regeneration without losing the original activity and stability for water treatment applications.