Characterisation of bare and tannase-loaded calcium alginate beads by microscopic, thermogravimetric, FTIR and XRD analyses

Modulating alginate-polyurethane elastomer properties: Influence of NCO/OH ratio with aliphatic diisocyanate

This research addresses the need for enhanced biomaterials by investigating the influence of the NCO/OH ratio on sodium alginate-based polyurethane elastomers(Al-PUEs), offering novel insights into their structural, thermal, mechanical and swelling behavior. Al-PUEs were prepared by blending the chain extenders with key ingredients in a specific molar ratio using aliphatic HMDI and HTPB monomers. The chemical linkages, crystalline behavior, homogeneity, and surface morphology of PUEs were evaluated by FT-IR, XRD, SEM, and EDX analysis. Thermo-mechanical studies were performed using TGA, DSC and tensile testing. Swelling behavior and absorption analysis were analyzed in DMSO and water. The analysis indicated that the hydrophilicity and swelling behavior of the prepared PUEs were affected by the addition of sodium alginate content. The results exhibit the tailor-made network structure of Al-PUEs, resulting in better thermal stability, elasticity of materials via stress-strain behavior and marvelous characteristic features than traditional high-tech yields. Furthermore, the resulting Al-PUEs are potential candidates for biomedical implants.

Preparation and Characterization of Silica-Coated Sodium Alginate Hydrogel Beads and the Delivery of Curcumin

In this study, to address the defects of sodium alginate (SA), such as its susceptibility to disintegration, silica was coated on the outer layer of sodium alginate hydrogel beads in order to improve its swelling and slow-release properties. Tetraethyl orthosilicate (TEOS) was used as the hydrolyzed precursor, and the solution of silica precursor was prepared by sol-gel reaction under acidic conditions. Then SA-silica hydrogel beads prepared by ionic crosslinking method were immersed into the SiO2 precursor solution to prepare SA-silica hydrogel beads. The chemical structure and morphology of the hydrogel beads were characterized by XRD, FTIR, and SEM, and the results showed that the surface of SA-silica beads was successfully encapsulated with the outer layer of SiO2, and the surface was smooth and dense. The swelling experiments showed that the swelling performance effectively decreased with the increase of TEOS molar concentration, and the maximum swelling ratio of the hydrogel beads decreased from 41.07 to 14.3, and the time to reach the maximum swelling ratio was prolonged from 4 h to 8 h. The sustained-release experiments showed that the SA-silica hydrogel beads possessed a good pH sensitivity, and the time of sustained-release was significantly prolonged in vitro. Hemolysis and cytotoxicity experiments showed that the SA-silica hydrogel beads were biocompatible when the TEOS molar concentration was lower than 0.375 M. The SA-silica-2 hydrogel beads had good biocompatibility, swelling properties, and slow-release properties at the same time.

Synergy of Magnetic Nanoparticles and Sodium Alginate-Coated Lignin for Effective Pollutant Remediation, Simple Recovery, and Cost-Effective Regeneration

In the pursuit of sustainable materials for environmental remediation, this study presents the development and comprehensive characterization of cobalt ferrite nanoparticles (CFNPs) incorporated in lignocellulosic-derived sodium alginate (CFNPs@LCG-SA) biocomposite beads. These biobased beads exhibit exceptional adsorption capabilities, particularly for methylene blue (MB) dyes, rendering them promising candidates for wastewater treatment. Using a comprehensive range of analytical techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis-derivative thermogravimetry (TGA/DTG), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), etc., we elucidated their structural, physicochemical, and thermal properties. Their multifunctional nature, derived from lignin and sodium alginate components, provides ample active sites for both physical interactions and chemical bonding with contaminants apart from the magnetic character attributed by the CFNPs. With a freeze-drying approach, the optimal adsorption capacity and removal rate of MB reached 97 mg/g and 99%, respectively, and no meaningful decline in their activity was noted even after six cycles. The CFNPs@LCG-SA biocomposite beads emerge as a cost-efficient and sustainable remedy for environmental cleanup, offering valuable perspectives in environmental preservation and advancing green energy technologies.

Preparation, Characterization and Stability of Calcium-Binding Peptides Derived from Chicken Blood

Calcium-binding peptides have gained significant attention due to their potential applications in various fields. In this study, we aimed to prepare, characterize, and evaluate the stability of calcium-binding peptides derived from chicken blood. Chicken hemoglobin peptides (CPs) were obtained by protease hydrolysis and were applied to prepare chicken hemoglobin peptide-calcium chelate (CP-Ca). The preparation conditions were optimized, and the characteristics and stability of CP-Ca were analyzed. The optimal chelating conditions were determined by single-factor and response surface tests, and the maximum calcium ion chelating rate was 77.54%. Amino acid analysis indicated that glutamic acid and aspartic acid motifs played an important role in the chelation of the calcium ions and CP. According to the characterization analysis, CP-Ca was a different substance compared with CP; calcium ions chelated CPs via the sites of carbonyl oxygen, carboxyl oxygen, and amino nitrogen groups; and after the chelation, the structure changed from a smooth homogeneous plate to compact granular. The stability analysis showed that CP-Ca was stable at different temperatures, pH, and gastrointestinal conditions. The study indicates that chicken blood is a promising source of peptide-calcium chelates, providing a theoretical basis for application in functional foods and improving the utilization value of chicken blood.

Silica-Reinforced AMP-Calcium Alginate Beads for Efficient and Selective Removal of Cesium from a Strong Acidic Medium

Due to the significant selectivity for Cs+, ammonium molybdophosphate (AMP) possesses potential to uptake radiocesium from high-level liquid waste (HLLW), whereas its micro-crystalline structure and fine powder morphology limit its industrial application. Although the granulation method with alginate is prospective for the preparation of an AMP exchanger, the mechanical strength of obtained beads may be insufficient for application. In this context, we prepared silica-reinforced AMP-calcium alginate (ACS) beads and evaluated their performance for Cs+ removal from strong acidic solutions. It was found that the addition of silica in the fabrication significantly improved the mechanical strength of the beads in comparison to those without silica. Notably, the beads with an AMP/silica mass ratio of 1.0 exhibited an exceptional mechanical strength, surpassing that of ACS beads composed of other components. The batch experiment results indicated that the Cs+ adsorption follows a non-linear pseudo-second-order rate equation. The distribution coefficient of Cs+ was high even in extreme acidic conditions (∼1.6 × 102 mL/g in 8.0 mol/L HNO3 solution). The Cs+ adsorption can be well fitted with the Langmuir model, and the estimated maximum exchange capacity in 3.0 mol/L HNO3 could reach 23.9 mg/g. More importantly, ACS beads showed excellent selectivity toward Cs+ uptake over eight co-existing metal ions in simulated HLLW, with separation factor values all above 145. The column experiment exhibited that the beads can serve as the stationary phase in columns to effectively remove Cs+. The findings of this study are significant as they provide insights into the development of efficient materials for radiocesium removal from high-level liquid waste. The results demonstrate the potential of silica-reinforced ACS beads for Cs+ adsorption, with promising applications in industrial settings.

Antibacterial, antioxidant, Cr(VI) adsorption and dye adsorption effects of biochar-based silver nanoparticles‑sodium alginate-tannic acid composite gel beads

Ultrasonic extraction of Osmanthus fragrans was used for reducing Ag+ to prepare AgNPs, which were further loaded on barley distiller's grains shell biochar. By supplementary of sodium alginate and tannic acid, composite gel beads were prepared. The physical properties of biochar-based AgNPs‑sodium alginate-tannic acid composite gel beads (C-Ag/SA/TA) were characterized. SEM, FTIR, and XRD showed that biochar-based AgNPs were compatible with sodium alginate-tannic acid. CAg greatly improved the dissolution, swelling, and expansion of gel beads. Through the analysis by the agar diffusion method, C-Ag/SA/TA gel beads had high antibacterial activity (inhibition zone: 22 mm against Escherichia coli and 20 mm against Staphylococcus aureus). It was observed that C-Ag/SA/TA composite gel beads had high antioxidant capacity and the free radical scavenging rate reached 89.0 %. The dye adsorption performance of gel beads was studied by establishing a kinetic model. The maximum adsorption capacities of C-Ag/SA/TA gel beads for methylene blue and Congo red were 166.57 and 318.06 mg/g, respectively. The removal rate of Cr(VI) reached 96.4 %. These results indicated that the prepared composite gel beads had a high adsorption capacity for dyes and metal ions. Overall, C-Ag/SA/TA composite gel beads were biocompatible and had potential applications in environmental pollution treatment.

Physical characterization, biocompatibility, and antimicrobial activity of polyvinyl alcohol/sodium alginate blend doped with TiO2 nanoparticles for wound dressing applications

The ability of wound dressing materials to tackle skin pathogens colonization that is associated with open wound infections is limited. Recently, green-synthesized metal oxide nanoparticles has received a lot of attention to overcome this limitation. However, titanium dioxide nanoparticles (TiO2-NPs) exhibit exceptional antibacterial properties. In this work, several concentrations (0, 1, 3, and 5 wt.%) of TiO2 NPs prepared using Aloe vera leaf extract were added to a blend of polyvinyl alcohol and sodium alginate (PVA:SA). This nanocomposite was designed to enhance the healing process of wounds. The interaction between the PVA:SA composite and the TiO2 NPs was confirmed by FTIR. The thermal behavior of the nanocomposite films was investigated using DSC and TGA. The experimental results indicate that the glass transition temperatures of the nanocomposites increased by increasing the added amount of TiO2 NPs to be 53.7 °C (1 wt.%), 55.8 °C (3 wt.%), and 60.6 °C (5 wt.%), which were consistently lower than the glass transition temperature of the matrix material (69.6 °C). The Dynamic Mechanical Analysis was examined. The nanocomposite doped with 5 wt.% of TiO2 NPs detected a high storage modulus (21.6 × 108). Based on swelling and degradation studies, the prepared PVA:SA:TiO2 nanocomposite films have an excellent swelling rate, and the inclusion of TiO2 NPs increases the stability of the polymeric matrix. The PVA:SA:TiO2 nanocomposite films exhibited a superior antibacterial efficacy against Gram-positive bacteria such as Bacillus cereus and Staphylococcus aureus, compared to their effectiveness against Gram-negative bacteria like Escherichia coli. Moreover, the nanocomposite films were biocompatible with Human Skin Fibroblast. Therefore, the developed PVA:SA:TiO2 nanocomposite films suit wound dressing applications.

Bioinspired Zn-MOF doped radial porous chitosan-based sponge with antibacterial and antioxidant properties for rapid hemostasis and wound healing

Herein, a novel bioinspired radial porous zinc-based metal-organic framework (Zn-MOF) doped sodium alginate/chitosan derivatives/pullulan-based SA/PSCS/Pul/Zn-MOF (SPCP/Zn) composites sponge with excellent antioxidant and antibacterial properties was fabricated by the ice-templating method. Boric acid (BA) and Ca2+, which were respectively used as hydrogen- and ionic- bonding cross-linkers, provided strong mechanical properties for sponge matrix composed of SA, PSCS, and Pul. The obtained SPCP/Zn sponge exhibited uniform porous morphology, proper hydrophilicity, and admirable biocompatibility. In addition, the SPCP/Zn sponge achieved a sustained release of Zn2+ and gallic acid, which displayed powerful antibacterial and antioxidant activities. Importantly, the SPCP/Zn sponge exhibited shorter rapid hemostasis (20.4 ± 2.9 s) and lower blood loss (19.8 ± 4.3 mg). The SPCP/Zn sponge also showed faster wound closure ratio for the rat full-thickness skin defect model. It was revealed that SPCP/Zn sponge could significantly accelerate and enhance wound healing through downregulating inflammatory cytokines (TNF-α, IL-6) and increasing the expression of growth factors (VEGF). Due to its excellent properties, the SPCP/Zn sponge may have promising potential in wound healing applications.

Encapsulation of probiotics in freeze-dried calcium alginate and κ-carrageenan beads using definitive screening design: A comprehensive characterisation and in vitro digestion study

This research aimed to evaluate the encapsulation of the probiotic strain, Streptococcus thermophilus, in hydrogels employing sodium alginate (SA) with κ-carrageenan (κC) in gelation baths with varying salt concentrations (CaCl2 and KCl) followed by freeze-drying. The experimentation was conducted at varying levels of κC (0-0.5 % w/v) and SA (2-4 %). Freeze-dried hydrogels were evaluated based on encapsulation efficiency and loss of viability and further characterised. The study could successfully establish an encapsulation efficiency of 87.814 % and a viability loss of 1.201 log CFU·g-1 for the optimised samples. The SEM micrographs of the optimised Ca-alginate/κC hydrogels exhibited a much denser network with fewer pores. The influence of SA/κC in the beads was confirmed by FTIR and DSC, where distinct peak shifts were observed, which indicated the presence of κC and SA polymers. The probiotic survival under simulated gastrointestinal tract (GIT) conditions, performed in accordance with the INFOGEST protocol, indicated that the optimised Ca-alginate/κC beads had a lower rate of release in the gastric phase and a much higher rate of survival and release in the intestinal phase than the control sample. The swelling behaviour of beads varied due to varying pH in both gastric and intestinal phases, and the κC in the optimised beads affected the swelling ratio significantly.

Effect of the magnetic core in alginate/gum composite on adsorption of divalent copper, cadmium, and lead ions in the aqueous system

The change of composition of an adsorbent material has been widely used as a method to increase its adsorption capacity, particularly concerning adsorbents made of polysaccharides. Introducing magnetic adsorbents into contaminated water treatment systems is a highly promising strategy, as it promotes the metal ions removal from water. Considering this, gum Arabic (GA) was associated with alginate (Alg), when magnetite nanoparticles were present or absent, to produce beads that were utilised to take up Cu(II), Cd(II), and Pb(II) from aqueous solution. After a complete characterisation (for which Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and swelling were used), the adsorption properties were established using batch and column tests. The magnetic beads (MAlg/GA) demonstrated improved adsorption in comparison with the beads made without magnetite (Alg/GA) under the same conditions. In normal adsorption conditions (pH 6.0, 25 °C, 2.5 g L-1 of adsorbent dosage), the highest uptake capacities recorded for the MAlg/GA beads were: for Cu(II), 1.33 mmol g-1; Cd(II), 1.59 mmol g-1; and for Pb(II), 1.43 mmol g-1. The pseudo-second-order kinetics and Langmuir isotherm models provided good fits for the adsorption of these metals. Overall, ion exchange and physical forces led to the uptake of these metals by both Alg/GA and MAlg/GA; moreover, the functional groups on the beads played crucial roles as binding sites. Additionally, it was observed that flow rates of >2 mL min-1 did not produce noticeable changes in uptake levels over the same flow period. It was found that the efficient eluting agent was HNO3 (0.2 M). In some cases, the metals were not removed fully from the used beads during the first five cycles of regeneration and reuse. The results of this investigation show that these beads are efficient adsorbents for the removal of metal ions from spiked well water samples.

Slow-release microencapsulates containing nanoliposomes for bioremediation of soil hydrocarbons contaminated

Encapsulation and nutrient addition in bacterial formulations have disadvantages concerning cell viability during release, storage, and under field conditions. Then, the objective of this work was to encapsulate a bacterial consortium with hydrocarbon-degrading capacities in different matrices composed of cross-linked alginate/ polyvinyl alcohol /halloysite beads (M1, M2, and M3) containing nanoliposomes loaded with or without nutrients and evaluate their viability and release in a liquid medium, and soil (microcosmos). Also, evaluate their capacity to remove total petroleum hydrocarbons (TPH) for 165 days and matrices characterization. The encapsulate consortium showed a quick adaptation to contaminated soil and a percentage of removal (PR) of TPH up to 30% after seven days. All the matrices displayed a PR of up to 90% after 165 days. The matrix M2 displayed significant resistance to degradation and higher cell viability with a PR of 94%. This result supports the encapsulation of bacteria in a sustainable matrix supplemented with nutrients as a well-looked strategy for improving viability and survival and, therefore, enhancing their effectiveness in the remediation of hydrocarbon-contaminated soils.

Tannic Acid and Ca2+ Double-Crosslinked Alginate Films for Passion Fruit Preservation

In this study, the interaction of different concentrations of tannic acid (TA) (10%, 20%, and 30% w/w) and Ca2+ with alginate (SA) was utilized to create double-crosslinked SA films. The resulting films were evaluated for their optical, mechanical, water resistance, and barrier properties, and their microstructure and intermolecular interactions were also characterized. The SA films containing 20% TA showed the best mechanical properties, with an observed increase in tensile strength of 22.54%. In terms of water vapor permeability, the SA film containing 30% TA exhibited the highest barrier property, which was 25.36% higher than that of the pure SA film. Moreover, TA demonstrated a strong UV absorption ability, resulting in a nearly 0% UV transmittance of the SA film at 280 nm. It can be seen that SA films containing 20% TA have excellent barrier and mechanical properties, and the development of such films will be applied to the storage and packaging of fresh food. It is worth noting that this work also investigated the effect of SA coatings containing different concentrations of TA on the preservation of passion fruits for 7 days. The results revealed that passion fruits treated with SA coatings containing a 30% TA concentration maintained a better appearance on the 7th day and had the lowest weight loss and crumpling indices of approximately 8.98% and 2.17, respectively, compared to the other treatment groups. Therefore, based on the overall results, the addition of 30% TA to SA coatings proved to be more effective and can be considered a promising approach for delaying fruit senescence and decay.

Plant-inspired adhesive and injectable natural hydrogels: in vitro and in vivo studies

The development of alternative therapeutic treatments based on the use of medicinal and aromatic plants, such as Juniper communis L., has aroused interest in the medical field to find new alternatives to conventional therapeutic treatments, which have shown problems related to bacterial resistance, high costs, or sustainability in their production. The present work describes the use of hydrogels based on sodium alginate and carboxymethyl cellulose, with combinations of juniperus leaves and berry extracts, in order to characterize their chemical characteristics, antibacterial activity, tissue adhesion test, cytotoxicity in the L929 cell line, and their effects on an in vivo model in mice to maximize the use of these materials in the healthcare field. Overall, an adequate antibacterial potential against S. aureus, E. coli and P. vulgaris was obtained with doses above 100 mg.mL-1 of hydrogels. Likewise, low cytotoxicity in hydrogels combined with extracts has been identified according to the IC50 value at 17.32 µg.mL-1, compared to the higher cytotoxic activity expressed by the use of control hydrogels with a value at 11.05 µg.mL-1. Moreover, in general, the observed adhesion was high to different tissues, showing its adequate capacity to be used in different tissue typologies. Furthermore, the invivo results have not shown erythema, edema, or other complications related to the use of the proposed hydrogels. These results suggest the feasibility of using these hydrogels in biomedical applications given the observed safety.

Alginate-based porous polyHIPE for removal of single and multi-dye mixtures: Competitive isotherm and molecular docking studies

A novel hydrophilic porous alginate-based polyHIPE (AGA) was synthesized via an oil-in-water emulsion templating approach. AGA was used as an adsorbent for removing methylene blue (MB) dye in single- and multi-dye systems. BET, SEM, FTIR, XRD, and TEM were used to characterize AGA to elucidate its morphology, composition and physicochemical properties. According to the results, 1.25 g/L AGA adsorbed 99 % of 10 mg/L MB in 3 h in a single-dye system. The removal efficiency decreased to 97.2 % in the presence of 10 mg/L Cu2+ ions and 40.2 % when the solution salinity increased to 70 %. In a single-dye system, the experimental data do not match well with the Freundlich isotherm, pseudo-first order, and the Elovich kinetic model, however, in a multi-dye system, it fit well with both extended Langmuir and the Sheindorf-Rebhun-Sheintuch. Notably, AGA removed 66.87 mg/g in a dye solution containing only MB, whereas 50.14-60.01 mg/g adsorption of MB was accomplished in a multiple-dye system. According to the molecular docking analysis, the dye removal process involved chemical bonds between the functional groups of AGA and the dye molecules, hydrogen bonds, hydrophobic and electrostatic interactions. The overall binding score of MB decreased from -26.9 kcal/mol in a single-dye system to -18.3 kcal/mol in a ternary system.

Alginate microbeads incorporated with anthocyanins from purple corn (Zea mays L.) using electrostatic extrusion: Microencapsulation optimization, characterization, and stability studies

Microencapsulation of purple corn anthocyanins was carried out via an electrostatic extruder using alginate as a wall material. The influence of alginate concentration (1-2 %), extract concentration (20-30 %), and extrusion voltage (3-5 kV) on encapsulation efficiency and mean particle size was evaluated using response surface methodology. Optimal conditions were obtained to produce two different extract-loaded microbeads. Microbeads with the highest encapsulation efficiency (EE) and minimum particle size were achieved at 1 % alginate, 20 % extract, and 5 kV extrusion voltage (EEC3G = 70.26 %, EETPC = 91.59 %, particle size = 1.29 mm). In comparison, the microbeads with the efficient entrapment and maximum particle size were obtained at 1 % alginate, 26 % extract, and 3 kV (EEC3G = 81.15 %, EETPC = 91.01 %, particle size = 1.87 mm). Brunauer-Emmett-Teller (BET) surface area, pore size, and pore volume decreased after the inclusion of extract, with the lowest values reported for the smallest microbeads containing the extract. Scanning electron microscopy confirmed the results obtained by BET method and demonstrated fewer cracks and lower shrinkage of encapsulated samples. Fourier-transform infrared results proved the presence of anthocyanins and further possible interactions between phenolics and alginate. Stability studies revealed the color maintenance of anthocyanins-loaded microbeads during 4 weeks of storage at 4 °C and 8 °C. Moreover, the small and large particles showed a 7.6 and 3.4-fold reduction in degradation rate at 4 °C compared to their unencapsulated counterparts. Anthocyanins-loaded alginate microbeads retained over 80 % of cyanidin-3-glucoside at 4 °C and 8 °C, suggesting a promising potential of optimized microbeads for intelligent packaging applications.

Synthesis and characterization of peanut hull modified chitosan beads

The incorporation of plant materials is an effective method to improve the stability of chitosan beads, as it further increases the adsorption of toxic dyes and metals from aqueous systems. In the present study, chitosan gels were impregnated with a novel type of powder as the groundnut hull powder in order to form composite beads by using a simple droplet-based microfluidic system. The beads were then characterised through various techniques such as SEM, TGA, FTIR, and XRD. Microscopic imaging revealed a change in the surface morphology of the composite beads, which became rough and wrinkled with more valley-like features and irregular cracks. FTIR data suggest that the impregnation of groundnut hull powder led to an increase in functional groups. The thermal analysis allowed for the assessment of composite bead hydration contents and indicated the presence of groundnut hull entrapped in the loaded beads, which was corroborated by vibrational spectroscopy. XRD analysis allows us to conclude that there is an involvement of groundnut hull in the chitosan gels, and the consequence of that is the formation of amorphous beads, which would make them suitable for the adsorption of toxic dyes and metals from water systems.

Biosorption of p-chloro meta xylenol (PCMX) by bacterium-encapsulated calcium alginate beads in a novel plug flow process

P-Chloro-Meta-Xylenol (PCMX) is a widely used disinfectant. In the current pandemic scenario, its consumption has increased largely, and as a result, wastewater is loaded heavily with PCMX as a contaminant. Remediation of this ecologically toxic phenolic compound is therefore a burning issue. This study proposes an eco-friendly biosorption-based remediation technique to remove PCMX. A novel isolated phenol-resistant gram-negative bacterium, Pandoraea sp. strain BT102, is first encapsulated in biopolymeric calcium alginate beads. These beads are packed in a long adsorption tube and the contaminated water was passed through this packed tube resembling a plug flow reactor. This unique plug-flow set-up is capable of reducing PCMX concentration from 100 mg L^-1 to 2.85 μg L^-1 within 4 h using only 30 g of adsorbent, resulting in 99.99% removal efficiency. Adsorption isotherms and kinetics are studied using batch experimental data. A PCMX loading capacity of the encapsulated calcium alginate beads is found to be 961.7 mg g^-1, and the Freundlich isotherm results suggested the phenomenon of cooperative adsorption. A good agreement of the pseudo-second-order kinetic model along with the intra-particle diffusion model suggests a multilayer diffusion-controlled adsorption process. Biosorption of PCMX by the bacterium-modified beads was confirmed by Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray (EDX), and Fourier-Transform Infrared spectroscopy (FT-IR) analyses. The application of multivariate model-based Response Surface Methodology (RSM) reveals flow rate to be the most important factor controlling the rate of bioremediation.

Enhanced bioremediation performance of diesel-contaminated soil by immobilized composite fungi on rice husk biochar

In response to the low removal capacity and poor tolerance of fungi to diesel-contaminated soil, a novel immobilization system using biochar to enhance composite fungi was proposed. Rice husk biochar (RHB) and sodium alginate (SA) were used as immobilization matrices for composite fungi, and the adsorption system (CFI-RHB) and the encapsulation system (CFI-RHB/SA) were obtained. CFI-RHB/SA exhibited the highest diesel removal efficiency (64.10%) in high diesel-contaminated soil over a 60-day remediation period compared to the free composite fungi (42.70%) and CFI-RHB (49.13%). SEM demonstrated that the composite fungi were confirmed to be well attached to the matrix in both CFI-RHB and CFI-RHB/SA. FTIR analysis revealed the appearance of new vibration peaks in diesel-contaminated soil remediated by immobilized microorganisms, demonstrating changes in the molecular structure of diesel before and after degradation. Furthermore, CFI-RHB/SA maintains a stable removal efficiency (>60%) in higher concentrations of diesel-contaminated soil. High-throughput sequencing results indicated that Fusarium and Penicillium played a key role in the removal of diesel contaminants. Meanwhile, both dominant genera were negatively correlated with diesel concentration. The addition of exogenous fungi stimulated the enrichment of functional fungi. The insights gained from experiment and theory help to provide a new understanding of immobilization techniques of composite fungi and the evolution of fungal community structure.

Application of Layered Double Hydroxides as a Slow-Release Phosphate Source: A Comparison of Hydroponic and Soil Systems

The utilization of slow-release fertilizer materials capable of responding to their environment and releasing nutrient ions efficiently over a prolonged period is an emerging research area in agricultural materials sciences. In this study, two-dimensional layered materials were prepared to release phosphor ions (P) slowly into the soil as well as in the hydroponic system. Various P-intercalated layered double hydroxides (LDHs) (Mg/Al, Zn/Al, and Mg-Zn/Al-LDHs) with a molar ratio of 2:1 were synthesized using an ion-exchange method from corresponding LDHs containing NO₃ ^- ions within the layers. Sodium alginate (SA) was used to encapsulate P-intercalated Mg/Al-LDH to produce bionanocomposite beads (LB) to check the effect of the biopolymer matrix on the release characteristics. The prepared materials were characterized by XRD and FTIR to confirm the incorporation of P in LDHs. TGA, SEM, and elemental analysis were also performed to study the thermal decomposition pattern, surface morphology, and chemical composition of synthesized materials. The P-release experiments were conducted in a soil solution. The performance of the prepared materials was investigated in soil as well as in a hydroponic system for tomato plants under a controlled atmosphere of humidity, temperature, and light. The fertilization ability of the prepared materials was compared with that of a soluble P source (KH₂PO₄), commercial hydroponic fertilizer (Nutrifeed), and a commercial soil slow-release fertilizer (Wonder plant starter). The prepared materials demonstrated a slow release of P in the soil solution. P-intercalated LDHs were not very effective under hydroponic conditions; however, the LDHs were more effective in the soil system in terms of dry matter production and P content in dry matter. Furthermore, LDHs were able to increase the soil pH value over time.

Encapsulation of Concentrated Solution Obtained by Block Freeze Concentration in Calcium Alginate and Corn Starch Calcium Alginate Hydrogel Beads

A model (sucrose and gallic acid) solution was concentrated by block freeze concentration (BFC) at three centrifugation cycles, and the solutions were encapsulated in calcium alginate and corn starch calcium alginate hydrogel beads. Static and dynamic tests determined the rheological behavior, differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) established thermal and structural properties, and the release kinetics was evaluated under in vitro simulated digestion experiment. The highest efficiency encapsulation value was close to 96%. As the concentrated solution increased in terms of solutes and gallic acid, the solutions were fitted to the Herschel-Bulkley model. Moreover, from the second cycle, the solutions exhibited the highest values of storage modulus (G') and loss modulus (G″), contributing to form a more stable encapsulation. The FTIR and DSC results demonstrated strong interactions between corn starch and alginate, establishing a good compatibility and stability in the bead formation. The kinetic release model under in vitro conditions was fitted to the Korsmeyer-Peppas model, demonstrating the significant stability of the model solutions inside the beads. Therefore, the present study proposes a clear and precise definition for the elaboration of liquid foods obtained by BFC and its incorporation inside an edible material that facilitates the controlled release in specific sites.

Adsorption of cationic and anionic dyes onto coffee grounds cellulose/sodium alginate double-network hydrogel beads: Isotherm analysis and recyclability performance

This work describes the preparation of new eco-friendly adsorbents with a simple method. Gel beads of coffee grounds cellulose (CGC) and sodium alginate (SA) were prepared for wastewater treatment. Upon their synthesis, the physicochemical properties, performances and efficiency were analyzed by means of various structural and morphological characterizations. Kinetic and thermodynamic adsorption approaches evaluated the removal capacity of these beads which reached equilibrium in 20 min for Methylene Blue (MB) and Congo Red (CR). Also, the kinetics shows that the results can be explained by the pseudo-second-order model (PSO). Furthermore, the isotherm assessments showed that Langmuir-Freundlich can fit the adsorption data of both contaminants. Accordingly, the maximum adsorption capacities reached by the Langmuir-Freundlich model are 400.50 and 411.45 mg/g for MB and CR, respectively. It is interesting to note that the bio-adsorption capabilities of MB and CR on bead hydrogels decreased with temperature. Besides, the results of the thermodynamic study evidenced that the bio-adsorption processes are favorable, spontaneous and exothermic. The CGC/SA gel beads are therefore outstanding bio-adsorbents, offering a great adsorptive performance and regenerative abilities.

Design and assembly of biodegradable capsules based on alginate hydrogel composite for the encapsulation of blue dye

The encapsulation of bluing agents in biodegradable polymeric capsules is an emerging option in laundry detergents sector to substitute formaldehyde-based polymers, because they are non-biodegradable, carcinogenic and toxic. In this work, we present for the first time the successful encapsulation of a blue dye in biodegradable capsules which shell was formed by an alginate hydrogel and a polyethylene glycol network. Different types of capsules were synthesized (addition or not of the diacrylate monomer) and irradiation of the crosslinking solution at different times. Furthermore, a deep characterization of each type of capsules was performed (chemical and morphological characterization, assessment of their mechanical and thermal properties, evaluation of their biodegradability), noting that the incorporation of the diacrylate monomer (PEGDMA) and the two different irradiation times selected substantially affected the final properties of the capsules. The obtained results will serve to comprehend how the dye can be released from the capsules.

Aspergillus terreus camptothecin-sodium alginate/titanium dioxide nanoparticles as a novel nanocomposite with enhanced compatibility and anticancer efficiency in vivo

BACKGROUND

Camptothecin derivatives are one of the most prescribed anticancer drugs for cancer patients, however, the availability, efficiency, and water solubility are the major challenges that halt the applicability of this drug.

METHODS

Biosynthetic potency of camptothecin by Aspergillus terreus, open a new avenue for commercial camptothecin production, due to their short-life span, feasibility of controlled growth conditions, and affordability for higher growth, that fulfill the availability of the scaffold of this drug.

RESULTS

Camptothecin (CPT) was purified from the filtrates of A. terreus, and their purity was checked by HPLC, and its chemical structure was verified by LC/MS, regarding to the authentic one. To improve the anticancer efficiency of A. terreus CPT, the drug was conjugated with sodium alginate (SA)/Titanium dioxide nanoparticles (TiO₂NPs) composites, and their physicochemical properties were assessed. From the FT-IR profile, a numerous hydrogen bond interactions between TiO₂ and SA chains in the SA/TiO₂ nanocomposites, in addition to the spectral changes in the characteristic bands of both SA/TiO₂ and CPT that confirmed their interactions. Transmission electron microscopy analysis reveals the spherical morphology of the developed SA/TiO₂NPs nanocomposite, with the average particle size ~ 13.3 ± 0.35 nm. From the results of zeta potential, successful loading and binding of CPT with SA/TiO₂ nanocomposites were observed.

CONCLUSION

The in vivo study authenticates the significant improvement of the antitumor activity of CPT upon loading in SA/TiO₂ nanocomposites, with affordable stability of the green synthesized TiO₂NPs with Aloe vera leaves extract.

A Comparison of Nitrate Release from Zn/Al-, Mg/Al-, and Mg-Zn/Al Layered Double Hydroxides and Composite Beads: Utilization as Slow-Release Fertilizers

Nitrate-loaded Zn/Al, Mg/Al, and Mg-Zn/Al layered double hydroxides (LDHs) were synthesized using the coprecipitation method. The slow-release properties of LDHs were measured in powder form at various pH conditions. Sodium alginate was used to encapsulate Mg/Al LDH to produce composite beads (LB) to further slow down the release of nitrate ions. The prepared LDH samples and LB were characterized by X-ray diffraction, attenuated total reflectance Fourier transform infrared spectroscopy, thermogravimetric analysis, and inductively coupled plasma optical emission spectroscopy. The surface morphologies of LDHs and LB were obtained from scanning electron microscopy analysis. The slow-release properties of the materials were evaluated using a kinetic study of nitrate release in tap water, soil solution, as well as plant growth experiments using coriander (Coriandrum sativum). The nitrate release ability of LDHs and LB was compared with a soluble nitrate source. The plant growth experiments showed that all three LDHs were able to supply an adequate amount of nitrate to the plant similar to the soluble fertilizer while maintaining the availability of nitrate over extended periods. The ability of LDHs to increase soil pH was also demonstrated.

Fenton degradation of ofloxacin antibiotic using calcium alginate beads impregnated with Fe3O4-montmorillonite composite

The primary aim of this study is to develop an economical, stable, and effective heterogeneous catalyst for wastewater remediation via the Fenton oxidation process. For this purpose, Fe₃O₄-montmorillonite alginate (FeMA) composite beads were synthesized by entrapping Fe₃O₄-montmorillonite in calcium alginate beads. The performance of the catalysts was evaluated via the Fenton degradation of ofloxacin (OFL), an antibiotic that is frequently detected in water bodies. The physiochemical properties of the FeMA composite beads were characterized using X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscope/energy dispersive X-ray (FESEM/EDX), Brunauer-Emmett-Teller (BET) analysis, Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA). FeMA composite beads were found to have a higher surface area, higher porosity, and better thermal stability compared to pristine alginate beads. The composite beads were subsequently used for Fenton degradation of ofloxacin (OFL) in an aqueous solution. The effects of Fe₃O₄-montmorillonite loading on alginate, FeMA composite beads dosage, initial solution pH, initial OFL concentration, different oxidants, H₂O₂ dosage, reaction temperature, and inorganic salts on Fenton degradation of OFL in aqueous solution was investigated. The results revealed that the percentage of OFL degradation reached about 80 % under optimized conditions, while the total organic carbon (TOC) removal reached about 53 %. The entrapment of Fe₃O₄-montmorillonite in alginate beads results in less iron ions leaching compared to previous observation, and the efficiency remains constant over the five cycles investigated. The kinetics of the Fenton degradation process are best fitted to the pseudo-first-order kinetic model. It is therefore believed that FeMA composite beads can be a promising material for wastewater remediation via the Fenton oxidation process.

Synthesis and Characterization of Calcium Alginate-Based Microspheres Entrapped with TiO2 Nanoparticles and Cinnamon Essential Oil Targeting Clinical Staphylococcus aureus

It is important to create new generations of materials that can destroy multidrug-resistant bacterial strains, which are a serious public health concern. This study focused on the biosynthesis of an essential oil entrapped in titanium dioxide (TiO₂) calcium alginate-based microspheres. In this research, calcium alginate-based microspheres with entrapped TiO₂ nanoparticles and cinnamon essential oil (CI-TiO₂-MSs) were synthesized, using an aqueous extract of Nigella sativa seeds for TiO₂ nanoparticle preparation, and the ionotropic gelation method for microsphere preparation. The microspheres obtained were spherical, uniformly sized, microporous, and rough surfaced, and they were fully loaded with cinnamon essential oil and TiO₂ nanoparticles. The synthesized microspheres were analyzed for antibacterial activity against the clinical multidrug-resistant strain of Staphylococcus aureus. Disc diffusion and flow cytometry analysis revealed strong antibacterial activity by CI-TiO₂-MSs. The synthesized CI-TiO₂-MSs were characterized by the SEM/EDX, X-ray diffraction, and FTIR techniques. Results showed that the TiO₂ nanoparticles were spherical and 99 to 150 nm in size, whereas the CI-TiO₂-MSs were spherical and rough surfaced. Apoptosis analysis and SEM micrography revealed that the CI-TiO₂-MSs had strong bactericidal activity against S. aureus. The in vitro antibacterial experiments proved that the encapsulated CI-TiO₂-MSs had strong potential for use as a prolonged controlled release system against multidrug-resistant clinical S. aureus.

Substantial increase in adsorption efficiency of local clay-alginate beads toward methylene blue impregnated with SDS

In the current research work, local clay-alginate beads loaded with sodium dodecyl sulfate (SDS) surfactant were prepared for efficient adsorption of methylene blue (MB). FTIR, SEM-EDX, and TGA instruments were used to examine the surface functional groups, morphology, elemental analysis, and thermal stability of beads, respectively. The adsorption efficiency of native clay for MB increases from 124.78 to 247.94 mg/g when loaded in alginate and SDS in beads form. The impacts of adsorbent dosage, initial pH, contact time, initial MB concentration, and temperature were investigated and optimized. The maximum adsorption capacity of beads for MB was 1468.5 mg/g. The process followed a pseudosecond order kinetic and Freundlich adsorption isotherm model. Thermodynamic study confirmed that MB adsorption on beads is endothermic and spontaneous in nature. The beads were recycled and reused for five times. According to the findings, local clay-alginate beads impregnated with SDS proved to be a promising and efficient adsorbent for extracting MB from aqueous solution.

Graphene Oxide-alginate Hydrogel for Drawing Water through an Osmotic Membrane

We report the preparation and evaluation of graphene oxide (GO)-enhanced alginate hydrogels for drawing water across an osmotic desalination membrane. GO-incorporated calcium alginate hydrogels (GO-HG) and pure calcium alginate hydrogels (P-HG) were synthesized for this study. Environmental scanning electron microscopy, water contact angle, and water uptake tests showed both samples to be strongly hydrophilic. The synthesized hydrogels demonstrated the ability to successfully and continuously draw water through a selective osmotic membrane in experiments. This was driven by the surface energy gradient-induced negative pressure between the more hydrophilic hydrogel and less hydrophilic membrane surface. The GO-HG was found to draw 21.2% more water than the P-HG, owing to the flexible GO nanosheets, which can be easily incorporated into the hydrogel framework. The GO nanosheets not only offer more hydrophilic functional sites but also enhance the connectivity within the alginate hydrogel framework so as to enhance the water production performance. The average amount of water drawn through the membrane by the GO-HG and the P-HG is 23.4 ± 0.9 g and 19.3 ± 1.8 g, respectively. It was found that no external stimuli were needed as water flows through the hydrogel due to gravitational force. The GO-enhanced alginate hydrogel, combined with the osmotic membrane, is a promising surface energy gradient-driven functional material for water purification and desalination without applying external pressure.

A bioresource catalyst system of alginate-starch-activated carbon microsphere templated Cu nanoparticles: Potentials in nitroarenes hydrogenation and dyes discoloration

The evolution and development of solid-matrix are considered a backbone for supporting and stabilizing of metal nanoparticles (NPs) and are the soul of the catalytic system. In the current study, the alginate-starch microsphere (Alg-St) was cross-linked using CaCl₂ as a cross-linker. In addition, the Alg-St microsphere was blended with different percentages of activated carbon (AC). The microspheres adsorbed Cu⁺² was reduced to zero-valent copper NPs through NaBH₄ and used as a dip-catalyst. The supported Cu NPs cum NaBH₄ system was used as dip-catalyst for the hydrogenation of 4-nitrophenol (4NP), 2-nitroanilline (2NA), and degradation of methylene blue (MB) and Congo red (CR) dyes. Among the different kinetics models, the experimental data were well-fitted in the zero-order kinetic model. Moreover pH, and recyclability were studied for 4NP, where the best activity was achieved at pH 7.0 for 4NP. No leaching was observed after 3rd cycle in the catalyst.

Changes in the Mechanical Properties of Alginate-Gelatin Hydrogels with the Addition of Pygeum africanum with Potential Application in Urology

New hydrogel materials developed to improve soft tissue healing are an alternative for medical applications, such as tissue regeneration or enhancing the biotolerance effect in the tissue-implant–body fluid system. The biggest advantages of hydrogel materials are the presence of a large amount of water and a polymeric structure that corresponds to the extracellular matrix, which allows to create healing conditions similar to physiological ones. The present work deals with the change in mechanical properties of sodium alginate mixed with gelatin containing Pygeum africanum. The work primarily concentrates on the evaluation of the mechanical properties of the hydrogel materials produced by the sol–gel method. The antimicrobial activity of the hydrogels was investigated based on the population growth dynamics of Escherichia coli ATCC 25922 and Staphylococcus aureus ATCC 25923, as well as the degree of degradation after contact with urine using an innovative method with a urine flow simulation stand. On the basis of mechanical tests, it was found that sodium alginate-based hydrogels with gelatin showed weaker mechanical properties than without the additive. In addition, gelatin accelerates the degradation process of the produced hydrogel materials. Antimicrobial studies have shown that the presence of African plum bark extract in the hydrogel enhances the inhibitory effect on Gram-positive and Gram-negative bacteria. The research topic was considered due to the increased demand from patients for medical devices to promote healing of urethral epithelial injuries in order to prevent the formation of urethral strictures.

Investigation into Biosorption of Pharmaceuticals from Aqueous Solutions by Biocomposite Material Based on Microbial Biomass and Natural Polymer: Process Variables Optimization and Kinetic Studies

Biosorbtive removal of the antibacterial drug, ethacridine lactate (EL), from aqueous solutions was investigated using as biosorbent Saccharomyces pastorianus residual biomass immobilized in calcium alginate. The aim of this work was to optimize the biosorption process and to evaluate the biosorption capacity in the batch system. Response surface methodology, based on a Box–Behnken design, was used to optimize the EL biosorption parameters. Two response functions (removal efficiency and biosorption capacity) were maximized dependent on three factors: initial concentration of EL solution, contact time, and agitation speed. The highest values for the studied functions (89.49%, 26.04 mg/g) were obtained in the following operational conditions: EL initial concentration: 59.73 mg/L; contact time: 94.26 min; agitation speed: 297.57 rpm. A number of nonlinear kinetic models, including pseudo-first-order, pseudo-second-order, Elovich, and Avrami, were utilized to validate the biosorption kinetic behavior of EL in the optimized conditions. The kinetic data fitted the pseudo-first-order and Avrami models. The experimental results demonstrated that the optimized parameters (especially the agitation speed) significantly affect biosorption and should be considered important in such studies.

Facile Synthesis of Sustainable Tannin/Sodium Alginate Composite Hydrogel Beads for Efficient Removal of Methylene Blue

To meet the requirement of sustainable development, bio-based adsorbents were developed for the removal of dye contaminant. To improve the adsorption capacity of pure sodium alginate (SA) adsorbent for the removal of methylene blue (MB), aromatic bio-based tannin (Tan) was incorporated through the cross-linking with calcium ion. The obtained Tan/SA composite hydrogel beads were characterized with SEM, FTIR and TG, demonstrating that millimeter-sized beads were obtained through calcium cross-linking with enhanced thermal stability. The maximum capacity (247.2 mg/g) at optimal condition (pH = 12, T = 45 °C) was obtained for the 40%Tan/SA adsorbents, with a removal efficiency of 82.4%. This can be ascribed to the electrostatic attraction between SA and MB, as well as the formation of π–π stacking between Tan and MB. The adsorption process for MB is endothermic, and chemical adsorption, the removal efficiency was exceeded 90% after five cycles.

Efficient Removal of Methylene Blue by Bio-Based Sodium Alginate/Lignin Composite Hydrogel Beads

Dye pollution is a serious issue in current environment protection, and bio-based adsorbents have been receiving much attention in wastewater treatment, due to their low cost, renewable, and environmentally friendly characteristics. Bio-based sodium alginate/lignin composite (SA/Lig) hydrogel beads were fabricated by a facile cross-linking with calcium ion and used for the removal of methylene blue (MB). The obtained SA/Lig microbeads were characterized with SEM, FTIR, and TG, and the effect of lignin content, pH, and temperature on the MB adsorption was investigated. The results indicated that the introduction of aromatic lignin can not only enhance thermal stability but also can improve the adsorption performance. Under optimal conditions, the maximum adsorption capacity (254.3 mg/g) was obtained for the SA/Lig-20% beads, with a removal efficiency of 84.8%. The adsorption process for MB is endothermic, and the rate-limiting step is chemical adsorption. The removal efficiency is higher than 90% after five cycles, revealing that the prepared beads show good regeneration ability.

Biosorption Potential of Microbial and Residual Biomass of Saccharomyces pastorianus Immobilized in Calcium Alginate Matrix for Pharmaceuticals Removal from Aqueous Solutions

Two types of biosorbents, based on Saccharomyces pastorianus immobilized in calcium alginate, were studied for the removal of pharmaceuticals from aqueous solutions. Synthetized biocomposite materials were characterized chemically and morphologically, both before and after simulated biosorption. Ethacridine lactate (EL) was chosen as a target molecule. The process performance was interpreted as a function of initial solution pH, biosorbent dose, and initial pharmaceutical concentration. The results exhibited that the removal efficiencies were superior to 90% for both biosorbents, at the initial pH value of 4.0 and biosorbent dose of 2 g/L for all EL initial concentrations tested. Freundlich, Temkin, Hill, Redlich-Peterson, Sips, and Toth isotherms were used to describe the experimental results. The kinetic data were analyzed using kinetic models, such as pseudo-first order, pseudo-second order, Elovich, and Avrami, to determine the kinetic parameters and describe the transport mechanisms of EL from aqueous solution onto biosorbents. Among the tested equations, the best fit is ensured by the pseudo-second-order kinetics model for both biosorbents, with the correlation coefficient having values higher than 0.996. The many potential advantages and good biosorptive capacity of Saccharomyces pastorianus biomass immobilized in calcium alginate recommend these types of biocomposite materials for the removal of pharmaceuticals from aqueous solutions.

Biosorptive Removal of Ethacridine Lactate from Aqueous Solutions by Saccharomyces pastorianus Residual Biomass/Calcium Alginate Composite Beads: Fixed-Bed Column Study

In this study, ethacridine lactate removal from aqueous solution using a biosorbent material based on residual microbial biomass and natural polymers in fixed-bed continuous column was investigated. Composite beads of Saccharomyces pastorianus residual biomass and calcium alginate were obtained by immobilization technique. The prepared biosorbent was characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy, and analysis of point of zero charge value. Then, laboratory-scale experiments by fixed-bed column biosorption were conducted in continuous system. To this purpose, the column bed high (5 cm; 7.5 cm), initial pollutant concentration (20 mg/L; 40 mg/L), and solution flow through the column (0.6 mL/min; 1.5 mL/min) were considered the main parameters. Recorded breakthrough curves suggest that lower flow rates, greater bed heights, and a lower concentration of ethacridine lactate led to an increased biosorption of the target compound. The biosorption dynamic was investigated by nonlinear regression analysis using the Adams–Bohart, Yoon–Nelson, Clark, and Yan mathematical models. Conclusively, our research highlights, firstly, that the obtained biosorbent material has the required properties for retaining the ethacridine lactate from aqueous solution in continuous system. Secondly, it emphasizes that the modeling approach reveals an acceptable fitting with the experimental data for the Yoon–Nelson, Clark, and Yan models.

Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation

The aim of this study was to investigate covalent immobilization of horseradish peroxidase (HRP) on magnetic nanoparticles (Mag) encapsulated in calcium alginate beads (MABs) for color degradation, combining easy and fast removal of biocatalyst from the reaction mixture due to its magnetic properties and strong binding due to surface alginate functional groups. MABs obtained by extrusion techniques were analyzed by optical microscopy, FEG-SEM and characterized regarding mechanical properties, magnetization and HRP binding. HRP with initial concentration of 10 mg/g_carrier was successfully covalently bonded on MABs (diameter ~1 mm, magnetite/alginate ratio 1:4), with protein loading of 8.9 mg/g_carrier, immobilization yield 96.9% and activity 32.8 U/g. Immobilized HRP on MABs (HRP-MABs) was then used to catalyze degradation of two anthraquinonic dyes, Acid Blue 225 (AB225) and Acid Violet 109 (AV109), as models for wastewater pollutants. HRP-MABs decolorized 77.3% and 76.1% of AV109 and AB225, respectively after 15 min under optimal conditions (0.097 mM H₂O₂, 200 mg of HRP-MABs (8.9 mg/g_carrier), 0.08 and 0.1 g/mg beads/dye ratio for AV109 and AB225, respectively). Biocatalyst was used for 7 repeated cycles retaining 75% and 51% of initial activity for AB225 and AV109, respectively, showing potential for use in large scale applications for colored wastewater treatment.

Development and characterization of cannabidiol-loaded alginate copper hydrogel for repairing open bone defects in vitro

The clinical treatment of open bone defects caused by accidental bone trauma, bone tumors, bone diseases and bone infections is challenging. In this study, we designed and fabricated a multifunctional alginate-based hydrogel that contains cannabidiol (CBD), SA@Cu/CBD hydrogel, for repairing open bone defects. The results of physicochemical characterization showed that the SA@Cu/CBD hydrogel was successfully prepared and showed a suitable swelling ratio, high thermal stability, and stable mechanical properties. In vitro evaluation of antibacterial activity indicated that more than 90% of S. aureus and E. coli were inhibited compared to the control group. The ALP activity assay showed that the ALP expression level of MC3T3-E1cells in SA@Cu/CBD hydrogel was approximately 2-fold higher than that in the control group on day 7 and 14. Additionally, compared to the control group, the level of mineralized deposits in SA@Cu/CBD hydrogel was also improved by about 2 times on day 14. The PCR results indicated the mRNA expression levels of osteogenic markers (ALP, Col1α1, OCN, and RUNX2 genes) and angiogenic markers (EGFL6 and VEGF genes) in SA@Cu/CBD hydrogel were significantly upregulated compared to that in the control group, and the mRNA expression levels of critical inflammatory cytokines (TNF-α and IL-1β) in the SA@Cu/CBD hydrogel were significantly down-regulated compared to that in SA@Cu hydrogel. Taken together, these results demonstrated that the SA@Cu/CBD hydrogel showed significantly anti-bacterial, anti-inflammation, angiogenic and osteogenic activities in vitro studies. Thus, SA@Cu/CBD hydrogels may be a promising candidate in repairing open bone defects.

Fluorescence microscope observation of the structure of a calcium alginate hydrogel

Calcium alginate hydrogels are used in a wide range of applications in the food, medical, pharmaceutical, and cosmetic industries. I have studied a calcium alginate hydrogel as an ultrasound phantom material. This hydrogel is formed using sodium alginate, calcium sulfate dihydrate, trisodium phosphate 12-hydrate, glycerol, and water, and mimics the ultrasound properties of human soft tissue. In this study, the structure of the calcium alginate hydrogel was observed with a fluorescence microscope after staining with the calcium indicator calcein. Two types of hydrogel structures, tape-like and thread-like, were observed by this method. The thread-like structures were rare in the hydrogel, which made them more difficult to find than the tape-like structures. These structures were several micrometers in diameter and longer than the tape-like structures, which were several micrometers to several tens of micrometers wide. The thread-like structures spread out in three dimensions, and existed singly or in aggregates. The outer shape of the aggregated thread-like structures resembled the shape of the tape-like structures, which suggested that the tape-like structures were made up of thread-like structures. The tape-like and thread-like structures are thought to contribute to retention of water, which is the main component of a hydrogel, by surrounding it.