Formation and structural evolution of starch nanocrystals from waxy maize starch and waxy potato starch

Effect of sulfuric acid hydrolysis on the structure and Pickering emulsifying capacity of acorn starch

The acid-hydrolyzed acorn starch samples (HAS-1, HAS-2, HAS-3, and HAS-4) were prepared from natural acorn starch (NAS) at sulfuric acid concentrations of 1, 2, 3, and 4 mol/L for 2 d. The particle characteristics and structures of HAS were investigated, and Pickering high internal phase emulsions (HIPEs) based on HAS were constructed and characterized. The results showed that with an increase in sulfuric acid concentration, the size, yield, amylose content, molecular weight, and amylopectin chain length of HAS gradually decreased. HAS retained an A-type crystal structure, and its relative crystallinity and short-range order degree gradually increased with increasing sulfuric acid concentration. Acid hydrolysis treatment improved the wettability of NAS, and its effect was positively correlated with the sulfuric acid concentration. HAS-3 and HAS-4 could stabilize the Pickering HIPEs with an oil phase volume fraction of 80% at c ≥ 1.5%. The mechanical properties of the HIPEs were positively correlated with c.

Starch nanoparticles with predictable size prepared by alternate treatments of ball milling and ultrasonication

In this study, starch nanoparticles (SNPs) were prepared by alternate treatments of liquid nitrogen ball milling and ultrasonication. The impact, shear and friction forces produced by ball milling, and acoustic cavitation and shear effects generated by ultrasonication disrupted starch granules to prepare SNPs. The SNPs possessed narrow particle size distribution (46.91-210.52 nm) and low polydispersity index (0.28-0.45). Additionally, the SNPs exhibited the irregular fragments with good uniformity. The relative crystallinity decreased from 34.91 % (waxy corn starch, WCS) to 0-25.91 % (SNPs), and the absorbance ratios of R1047/1022 decreased from 0.81 (WCS) to 0.60-0.76 (SNPs). The SNPs had lower thermal stability than that of WCS, characterized by a decrease in Td (temperature at maximum weight loss) from 309.39 °C (WCS) to 300.39-305.75 °C (SNPs). Furthermore, the SNPs exhibited excellent swelling power (3.48-28.02 %) and solubility (0.34-0.97 g/g). Notably, oil absorption capacity of the SNPs (9.77-15.67 g/g) was rather greater than that of WCS (1.33 g/g). Furthermore, the SNPs possessed the lower storage modulus (G'), loss modulus (G″) and viscosity than that of WCS. The SNPs with predictable size and high dispersion capability prepared in this study lay a foundation for expanding the application of SNPs.

Fine molecular structure and digestibility changes of potato starch irradiated with electron beam and X-ray

The change of digestibility of starch irradiated with different types from the perspective of fine structure is not well understood. In this work, the change of internal structure, molecular weight and chain-length distribution, helical structure, lamellar structure, fractal structure and digestibility of native and treated potato starch with electron beam and X-ray was analyzed. Two irradiations caused the destruction of internal structure, the disappearance of growth rings and increase of pores. Irradiation degraded starch to produce short chains and to decrease molecular weight. Irradiation increased double helical content and the thickness and peak area of lamellar structure, resulting in the reorganization of amylopectin and increase of structure order degree. The protected glycosidic linkages increased starch resistance to hydrolase attack, thereby enhancing the anti-digestibility of irradiated starch. Pearson correlation matrix also verified the above-mentioned results. Moreover, X-ray more increased the anti-digestibility of starch by enhancing ability to change fine structure.

High-efficiency preparation of starch nanocrystals with small size and high crystallinity by ethanol-acid penetration and dry-heating pretreatment

Ethanol-acid penetration and drying-heating treatment was developed to shorten the preparation time and improve the quality of starch nanocrystals (SNCs). After treatment by optimized parameters, including 40 % ethanol solution, 10.6 mM chloric acid, and heating time of 1.5 h or 2.0 h, the starches exhibited weakened internal structure and relatively complete crystalline structure. Compared with the regular preparation of only acid hydrolysis, the regular final yield (8.5 % after 5 days) was reached in 48 h and 12 h of the starch heated at 1.5 h and 2.0 h, respectively. The micromorphology, molecular weight, and crystalline structure evaluation demonstrated that the collected nanoparticles were indeed SNCs with smaller size and higher relative crystallinity than regular SNCs. Further analysis found that the SNCs had better crystalline lamellae, higher thermal stability, and lower proportion of phosphorus and sulfur atoms than regular SNCs. This provided a potential method for the high-efficiency preparation of SNCs.

A smart thermoresponsive macroporous 4D structure by 4D printing of Pickering-high internal phase emulsions stabilized by plasma-functionalized starch nanomaterials for a possible delivery system

Hierarchically porous structures combine microporosity, mesoporosity, and microporosity to enhance pore accessibility and transport, which are crucial to develop high performance materials for biofabrication, food, and pharmaceutical applications. This work aimed to develop a 4D-printed smart hierarchical macroporous structure through 3D printing of Pickering-type high internal phase emulsions (Pickering-HIPEs). The key was the utilization of surface-active (hydroxybutylated) starch nanomaterials, including starch nanocrystals (SNCs) (from waxy maize starch through acid hydrolysis) or starch nanoparticles (SNPs) (obtained through an ultrasound treatment). An innovative procedure to fabricate the functionalized starch nanomaterials was accomplished by grafting 1,2-butene oxide using a cold plasma technique to enhance their surface hydrophobicity, improving their aggregation, and thus attaining a colloidally stabilized Pickering-HIPEs with a low concentration of each surface-active starch nanomaterial. A flocculation of droplets in Pickering-HIPEs was developed after the addition of modified SNCs or SNPs, leading to the formation of a gel-like structure. The 3D printing of these Pickering-HIPEs developed a highly interconnected large pore structure, possessing a self-assembly property with thermoresponsive behavior. As a potential drug delivery system, this thermoresponsive macroporous 3D structure offered a lower critical solution temperature (LCST)-type phase transition at body temperature, which can be used in the field of smart releasing of bioactive compounds.

Insights into starch-based gels: Selection, fabrication, and application

Starch a natural polymer, has made significant advancements in recent decades, offering superior performance and versatility compared to synthetic materials. This review discusses up-to-date diverse applications of starch gels, their fabrication techniques, and their advantages over synthetic materials. Starch gels renewability, biocompatibility, biodegradability, scalability, and affordability make them attractive. Also, advanced theoretical foundations and emerging industrial technologies could further expand their scope and functions inspiring new applications.

Impact of molecular structure of starch on the glutinous taste quality of cooked chestnut kernels

Chestnuts are a starchy food with a characteristic glutinous taste that is often used to assess their quality. In this study, our findings indicated that chestnuts with higher glutinous taste quality had lower amylose content and microcrystalline structures, as well as higher subcrystalline structures and relative crystallinity in both the raw and steamed starches. In the leached starch, chestnuts with higher glutinous taste quality had lower amylopectin B1 chains and microcrystalline structure, but higher amylopectin B2 chains, subcrystalline structure and relative crystallinity. These results suggest that amylose content, relative crystallinity, and amylopectin chain length distribution are important factors determining the glutinous taste quality of chestnuts. To further enhance our understanding of these factors, an sensory evaluation model was developed based on textural profile analysis parameters. This study provides valuable insights into the relationship between molecular structure of starch and the glutinous taste quality of starchy foods.

Red rice starch modification - Combination of the non-thermal method with a pulsed electric field (PEF) and enzymatic method using α-amylase

The objective of this study was to investigate the dual modification of red rice starch using pulsed electric field (PEF) and α-amylase, focusing on morpho-structural, thermal, and viscoamylographic properties. Native starch (Control) underwent various treatments: PEF at 30 kV cm-1 (PEF30), α-amylase at 9.0 U mg-1 (AA0), and a combination of both (PEF30 + α and α + PEF30). The PEF30 + α treatment exhibited the highest degree of digestion (10.66 %) and resulted in morphological changes in the starch granules, which became elongated and curved, with an increased average diameter of 50.49 μm compared to the control. The starch was classified as type A, with a maximum reduction in crystallinity of up to 21.17 % for PEF30. The deconvolution of FT-IR bands indicated an increase in the double helix degree (DDH) for PEF30 and AA0, while the degree of order (DO) was reduced for PEF30, AA0, and PEF30 + α. DSC analysis revealed significant modifications in gelatinization temperatures, particularly for PEF30, and these changes were supported by a reduction in gelatinization enthalpy (ΔH) of up to 28.05 % for AA0. These findings indicate that both individual and combined treatments promote a decrease in starch gelatinization and facilitate the process, requiring less energy. Differences were observed between the formulations subjected to single and alternating dual treatments, highlighting the influence of the order of PEF application on the structural characteristics of starch, especially when applied before the enzymatic treatment (PEF + α). Regarding the viscoamylographic parameters, it was observed that AA0 presented higher values than the control, indicating that α-amylase enhances the firmness of the paste. The double modification with PEF + α was more effective in reducing syneresis and starch retrogradation, leading to improvements in paste properties. This study provided significant insights into the modification of red rice starch using an efficient and environmentally friendly approach.

A new sight separation for collecting starch nanocrystals with small size and high crystallinity based on the hydrolysis mechanism

To prevent starch nanocrystals (SNCs) that are generated at an early stage from being hydrolyzed excessively, this study proposed a new separation method, named "neutral dispersion and acidic precipitation." SNCs were prepared from waxy potato starch by sulfuric acid hydrolysis. Based on the results of kinetics and molecular weight, the hydrolysis was divided into three stages, e.g., rapid (initial 1 day), medium (subsequent 1 day) and slow stage (2-5 days). The rapid and medium stages were related to the degradation of amorphous region in starch, and the slow stage mainly referred to SNC release. Therefore, the method was developed to separate SNCs at the slow stage. After centrifugation at 6000 rpm, large particles were removed from the SNC suspension under pH 7. The SNCs with small average size and crystallite size, high relative crystallinity (RC), and high dispersion stability in the supernatant were retained and were then precipitated entirely under pH 5, because pH 5 led to the reduction of dispersion stability of SNCs. Meanwhile, the hydrothermal and dry-thermal stability of separated SNCs were significantly promoted. The separation method has the potential in SNC preparation for increasing the yield and collecting products with small size and high RC.

A Review on Reinforcements and Additives in Starch-Based Composites for Food Packaging

The research of starch as a matrix material for manufacturing biodegradable films has been gaining popularity in recent years, indicating its potential and possible limitations. To compete with conventional petroleum-based plastics, an enhancement of their low resistance to water and limited mechanical properties is essential. This review aims to discuss the various types of nanofillers and additives that have been used in plasticized starch films including nanoclays (montmorillonite, halloysite, kaolinite, etc.), poly-saccharide nanofillers (cellulose, starch, chitin, and chitosan nanomaterials), metal oxides (titanium dioxide, zinc oxide, zirconium oxide, etc.), and essential oils (carvacrol, eugenol, cinnamic acid). These reinforcements are frequently used to enhance several physical characteristics including mechanical properties, thermal stability, moisture resistance, oxygen barrier capabilities, and biodegradation rate, providing antimicrobial and antioxidant properties. This paper will provide an overview of the development of starch-based nanocomposite films and coatings applied in food packaging systems through the application of reinforcements and additives.

Formation mechanism of starch nanocrystals from waxy rice starch and their separation by differential centrifugation

Starch nanocrystals (SNCs) were prepared from waxy rice starch via sulfuric acid hydrolysis. The objective focused on the following: i) the hydrolysis kinetics and structural properties of SNCs; ii) the effects of differential centrifugation on the yield and size distribution of SNCs. The hydrolysis was divided into a rapid hydrolysis stage in the initial two days and a slow hydrolysis stage after two days. During the two-day hydrolysis, the average diameter of SNCs reached 244 nm. After two days of hydrolysis, the degree of crystallinity, crystallite size, and melting temperature and enthalpy increased. The proportion of A-branched chains decreased, whereas the proportion of B1-branched chains and molecular weight did not change considerably. Thus, the reaction in the slow hydrolysis stage could be considered as the surface modification and gradual release of SNCs. Furthermore, SNCs with a small size and high charge density could be used for differential centrifugation.

Structural Properties of Lotus Seed Starch Nanocrystals Prepared Using Ultrasonic-Assisted Acid Hydrolysis

This study provides a novel method of preparing lotus seed starch nanocrystals (LS-SNCs) using acid hydrolysis combined with ultrasonic-assisted acid hydrolysis (U-LS-SNCs) and evaluates the structural characteristics of starch nanocrystals using scanning electron microscopy; analysis of particle size, molecular weight, and X-ray diffraction patterns; and FT-IR spectroscopy. The results showed that the preparation time of U-LS-SNCs could be reduced to 2 days less than that for LS-SNCs. The smallest particle size and molecular weight were obtained after a 30 min treatment with 200 W of ultrasonic power and 5 days of acid hydrolysis. The particle size was 147 nm, the weight-average molecular weight was 3.42 × 10⁴ Da, and the number-average molecular weight was 1.59 × 10⁴ Da. When the applied ultrasonic power was 150 W for 30 min and acid hydrolysis was applied for 3 days, the highest relative crystallinity of the starch nanocrystals was 52.8%. The modified nanocrystals can be more widely used in various applications such as food-packaging materials, fillers, pharmaceuticals, etc.

Synthesis of controlled-size starch nanoparticles and superparamagnetic starch nanocomposites by microemulsion method

In this study, a synthesis process based on the microemulsion method (ME) was developed with the aim to produce controlled-size starch nanoparticles (SNPs). Several formulations were tested for the preparation of the W/O microemulsions varying the organic/aqueous phase ratios and co-stabilizers concentrations. SNPs were characterized in terms of size, morphology, monodispersity and crystallinity. Spherical shape particles with mean sizes 30-40 nm were prepared. The method was then used to simultaneously synthesize SNPs and iron oxide nanoparticles with superparamagnetic properties. Starch-based nanocomposites with superparamagnetic properties and controlled size were obtained. Therefore, the microemulsion method developed could be considered an innovative technology for the design and development of novel functional nanomaterials. The starch-based nanocomposites were evaluated in terms of morphology and magnetic properties, and they are being considered as promising sustainable nanomaterials for different biomedical applications.

Multi-scale structures and physicochemical properties of waxy starches from different botanical origins

The multi-scale structures and physicochemical relationships of three different types of waxy starches (maize, tapioca, and potato) were investigated. The maize and tapioca starches exhibited A-type crystalline polymorph compared to potato starch (B-type). The WMS showed higher amorphous content (5.56 %) than other waxy starches. The WTS exhibited a low tendency of retrogradation with its high f_a (DP 6-12) and low f_b3 (DP ≥ 37) proportion of chains. Double helix content of WPS was observed highest with a high pasting viscosity (952.3 BU). Low f_a (DP 6-12) and high f_b3 (DP ≥ 37) chain proportions of the WPS retrograded easily. The compactness of the semi-crystalline aggregation structure influenced the retrogradation properties of waxy starches with a positive correlation. Furthermore, the peak viscosity of pastes was correlated with the proportion of f_b3 (DP ≥ 37) chains, mass fractal dimension, and double helix content. The results provide guidance to design the application of waxy starches in the production of clean-labels.