Nanomaterial-based surface-assisted laser desorption/ionization mass spectrometry of peptides and proteins

User-friendly platform for analysis of high mass intact proteins and glycopeptides by laser desorption/ionization-mass spectrometry based on copper oxide particles

Matrix-assisted laser desorption/ionization-mass spectrometry (MALDI-MS) based on micro/nanostructured materials with different natures has received increasing attention for the analysis of a wide variety of analytes. However, up to now, only a few studies have shown the application of simple platforms in MALDI-MS for the identification of intact proteins. The present work reports on the application of copper oxide particles (Cu2O PS), obtained by a greener route, in combination with low amounts of 2,5-dihydroxybenzoic acid (DHB) as a novel hybrid platform. The combined Cu2O PS@DHB matrix, containing only 2.5 mg mL-1 of particles and 10 mg mL-1 of DHB, was easily applicable in MALDI-MS without surface modification of target plates. Under optimal conditions, the analysis of intact proteins up to 150,000 Da was possible, including immunoglobulin G, bovine serum albumin, and cytochrome C with adequate spot-to-spot signal reproducibility (RSD < 10%). In addition, the analysis of glycopeptides from IgG digests was carried out to prove the multipurpose application of the Cu2O PS@DHB platform in the low m/z range (2500-3000 Da). From the obtained results, it can be concluded that the optical and surface properties of as-synthesized Cu2O PS are likely to be responsible for the superior performance of Cu2O PS@DHB in comparison with conventional matrices. In this sense, the proposed user-friendly methodology opens up the prospect for possible implementation in bioanalysis and diagnostic research.

Bacterial cellulose composite hydrogel for pre-concentration and mass spectrometric detection of thiol-containing biomarker

Simple soaking of bacterial cellulose (BC) membrane in carboxymethyl cellulose (CMC) solution yielded BC/CMC hydrogel having re-swellable property. Then, gold nanoparticles (AuNPs) were embedded in the BC/CMC hydrogel via in situ chemical reduction to form BC/CMC/AuNPs composite hydrogel. It was found that the composite hydrogel exhibited physical/chemical characteristics similar to those of BC. The AuNPs with an average diameter of 13 nm distributed uniformly within the BC/CMC matrix as verified by transmission electron microscopy. The novelty of this work is the application of the BC/CMC/AuNPs composite hydrogel for selective adsorption of an important thiol-containing biomarker of Alzheimer's disease, glutathione (GSH), prior to direct laser desorption/ionization mass spectrometric (LDI-MS) detection. GSH adsorbed in the BC/CMC/AuNPs composite hydrogel showed the high ionization signal in LDI-MS providing a linear range of 50-10,000 nM with a limit of detection as low as 54.1 nM, which is a cut-off level for distinguishing between normal individuals and Alzheimer's patients. It should be emphasized that an additional matrix was not necessary as AuNPs can act as self-matrix for LDI-MS analysis. Furthermore, the BC/CMC/AuNPs composite hydrogel can effectively preconcentrate GSH approximately 10 times upon adsorption allowing for ultrasensitive detection of GSH required for disease diagnosis.

Single-Walled Carbon Nanohorns as Boosting Surface for the Analysis of Low-Molecular-Weight Compounds by SALDI-MS

Limits of Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry (MS) in the study of small molecules are due to matrix-related interfering species in the low m/z range. Single-walled carbon nanohorns (SWCNH) were here evaluated as a specific surface for the rapid analysis of amino acids and lipids by Surface-Assisted Laser Desorption Ionization (SALDI). The method was optimized for detecting twenty amino acids, mainly present as cationized species, with the [M+K]⁺ response generally 2-time larger than the [M+Na]⁺ one. The [M+Na]⁺/[M+K]⁺ signals ratio was tentatively correlated with the molecular weight, dipole moment and binding affinity, to describe the amino acids’ coordination ability. The SWCNH-based surface was also tested for analyzing triglycerides in olive oil samples, showing promising results in determining the percentage composition of fatty acids without any sample treatment. Results indicated that SWCNH is a promising substrate for the SALDI-MS analysis of low molecular weight compounds with different polarities, enlarging the analytical platforms for MALDI applications.

Improvement in Ionization Efficiency Using Metal Oxide Nanoparticles in Laser Desorption/Ionization Mass Spectrometry of a Cancer Drug

Mass spectrometry imaging (MSI) without labeling has the potential for faster screening in drug development. Matrix-assisted laser desorption/ionization (MALDI) is typically used, but it has a large matrix size and uneven drug distribution. Surface-assisted laser desorption/ionization (SALDI) using nanoparticles (NPs) may overcome these issues. Here, the influence of NPs, solvent ratio, and order of dropping of NPs on SALDI-MSI of protoporphyrin IX (PpIX), a cancer drug, are reported. A solution of PpIX in a 50% aqueous solution of 50% acetonitrile at a concentration of 10 μM was used. The NPs include ZnO, Fe₃O₄, and four types of TiO₂. The NPs were fabricated by dissolving them on an aqueous 90% acetonitrile solution. Mass spectra were obtained with a time-of-flight mass spectrometer using a Nd:YAG laser at a 355-nm wavelength. The signal intensity using TiO₂ at a 0.5 mg/mL concentration in 50% acetonitrile was increased by 1.6-fold compared to that without TiO₂. Changing the solvent to 90% acetonitrile gave a uniform TiO₂ distribution and a 9-fold increase in the signal intensity for PpIX. Among the four types of TiO₂ with different particle sizes and crystal structures, TiO₂ with a smaller particle size and a rutile crystal structure produced the highest signal intensity. Forming a layer on top of the PpIX also resulted in an increased signal intensity. Hence, SALDI using TiO₂ provides effective ionization of the drug. In the future, we plan to investigate a spray method for the ionization of PpIX using TiO₂ for the MSI of various drugs.

MoS2-Assisted LDI Mass Spectrometry for the Detection of Small Molecules and Quantitative Analysis of Sulfonamides in Serum

A two-dimensional MoS₂ nanosheet was prepared by a chemical exfoliation method and served as an excellent matrix for the detection of small molecules by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS). In comparison with organic matrices (CHCA, 3-AQ) and a graphene matrix, we found that a MoS₂ matrix showed better performance in analysis of amino acids, peptides, fatty acids, and sulfonamides. A systematic comparison of the MoS₂ matrix with both ion modes showed that mass spectra produced in negative ion mode featured a corresponding single deprotonated ion, which was rather different from the complex multiple alkali metal addition peaks present in positive ion mode. In addition, better sensitivity and reproducibility were obtained in negative ion mode. The ionization mechanism of MoS₂ as a matrix in negative ion mode was further discussed. The deproton peak intensity of the analyte fatty acid decreased after the addition of the hole-scavenger KSCN, indicating that the ionization of the fatty acid was caused by the Auger complex effect of MoS₂ and electron injection. Experiments have shown that the MoS₂ matrix detects small molecules with good repeatability and can perform semiquantitative analysis of sulfonamides. Finally, the MoS₂ matrix was employed for quantitative determination of sulfamethoxine in serum samples by an internal standard method. This MoS₂-assisted laser desorption/ionization mass spectrometry (MoS₂-assisted LDI MS) method provides a simple, rapid, high-throughput approach to evaluate the drug levels in the patient serum and can achieve convenient drug therapy monitoring.

Engineering of nanomaterials for mass spectrometry analysis of biomolecules

Mass spectrometry (MS) based analysis has received intense attention in diverse biological fields. However, direct MS interrogation of target biomolecules in complex biological samples is still challenging, due to the extremely low abundance and poor ionization potency of target biological species. Innovations in nanomaterials create new auxiliary tools for deep and comprehensive MS characterization of biomolecules. More recently, growing research interest has been directed to the compositional and structural engineering of nanomaterials for enriching target biomolecules prior to MS analysis, enhancing the ionization efficiency in MS detection and designing biosensing nanoprobes in sensitive MS readout. In this review, we mainly focus on the recent advances in the engineering of nanomaterials towards their applications in sample pre-treatment, desorption/ionization matrices and ion signal amplification for MS profiling of biomolecules. This review will provide a toolbox of nanomaterials for researchers devoted to developing analytical methods and practical applications in the biological MS field.

TiN nanopillar-enhanced laser desorption and ionization of various analytes

The present paper reports on the use of TiN nanopillars as a robust analytical substrate for laser desorption/ionization mass spectrometry (LDI-MS). TiN nanopillars were fabricated on silicon wafers through the dynamic oblique deposition of titanium, followed by thermal treatment in an ammonia atmosphere. The TiN nanopillars were readily applicable to a simple "dried-droplet" method in the LDI-MS without surface modification or pre-treatment. A broad range of analytes were investigated, including a small drug molecule, a synthetic polymer, sugars, peptides, and proteins. Intact molecular signals were detected with low noise interference and no fragmentation. The developed TiN-nanopillar-based approach extends the applicable mass limit to 150 kDa (immunoglobulin G) and was able to detect trypsinogen (24 kDa) at levels as low as 50 fmol μL-1 with adequate shot-to-shot signal reproducibility. In addition, we carried out MS analysis on biomolecule-spiked human blood plasma and a mixture of standard samples to investigate the promise of the TiN nanopillars for clinical research. The experimental observations are validated using electromagnetic and heat-transfer simulations. The TiN nanopillars show a reduced reflection and exhibit surges in the TiN surface temperature upon irradiation with electromagnetic radiation. Localization of thermal energy at the tips of the TiN pillars is likely to be responsible for the superior LDI performance. Our results suggest that the development of nanostructured TiN substrates will contribute to the widespread implementation of nanostructured solid substrates for biomedical and clinical applications with simple processes.

Sensitive detection of clenbuterol by hybrid iridium/silicon nanowire-enhanced laser desorption/ionization mass spectrometry

There is increasing demand for anti-doping drug monitoring in sports and food safety checks by developing sensitive and fast analytical methods. Here we report the development of hybrid Ir/SiNW as a new MALDI matrix for the detection of small molecules. This matrix is characterized by sufficient UV absorption, low-noise background, and high efficiency in ionization of small molecules. Sensitive detection of clenbuterol (LOD: 0.18 pmol) and a variety of other small molecules has been achieved using the Ir/SiNW matrix with a reproducible performance. Compared to the individual components separately, the matrix of hybrid Ir/SiNW synthesized via in situ growth can promote the MS signal intensity by up to 10 fold under identical experimental conditions. We provide a unique mechanism for the high performance of the hybrid Ir/SiNW matrix with the characteristic properties of hydrogen atom transfer and enhanced protonation at the interface of the hybrid nanostructures. Our approach of using a hybrid Ir/SiNW matrix enables detection of clenbuterol quantitatively in complicated biological samples and in vivo experiments, promising a useful tool for food security and anti-doping drug monitoring in sports.

Machine learning of serum metabolic patterns encodes early-stage lung adenocarcinoma

Early cancer detection greatly increases the chances for successful treatment, but available diagnostics for some tumours, including lung adenocarcinoma (LA), are limited. An ideal early-stage diagnosis of LA for large-scale clinical use must address quick detection, low invasiveness, and high performance. Here, we conduct machine learning of serum metabolic patterns to detect early-stage LA. We extract direct metabolic patterns by the optimized ferric particle-assisted laser desorption/ionization mass spectrometry within 1 s using only 50 nL of serum. We define a metabolic range of 100-400 Da with 143 m/z features. We diagnose early-stage LA with sensitivity~70-90% and specificity~90-93% through the sparse regression machine learning of patterns. We identify a biomarker panel of seven metabolites and relevant pathways to distinguish early-stage LA from controls (p < 0.05). Our approach advances the design of metabolic analysis for early cancer detection and holds promise as an efficient test for low-cost rollout to clinics.

Fe3O4-assisted laser desorption ionization mass spectrometry for typical metabolite analysis and localization: Influencing factors, mechanisms, and environmental applications

Fe₃O₄ has been suggested as an efficient matrix for small-molecule analysis by laser desorption ionization mass spectrometry (LDI-MS), but thus far there has been no systematic study exploring the influencing factors of nano-Fe₃O₄ on the detection of typical metabolites, or the mechanism by which nano-Fe₃O₄ assists the desorption and ionization of analytes after receiving laser energy. In this study, Fe₃O₄ nanoparticles with different physicochemical properties were synthesized and characterized. The results revealed that smaller particle size and greater surface hydroxyl amount of nano-spherical Fe₃O₄ could improve the intensity and relative standard deviation of typical metabolites by LDI-MS. The thermally driven desorption process played a vital role in LDI performance, but the chemical interactions between nano-Fe₃O₄ and analytes did not. Good intra- or inter-spot repeatability and linearity of analytes were obtained by the optimum Fe₃O₄-assisted LDI-MS. Finally, the developed method was successfully used for the rapid analysis and localization of endogenous metabolites in biofluids and whole zebrafish tissue section samples. Our results not only elucidate the influencing factors and mechanisms of nano-Fe₃O₄ for the detection of typical metabolites in LDI-MS but also reveal an innovative tool for the imaging of chemicals in the regions of interest in terms of eco-toxicological research.

A spherical covalent-organic framework for enhancing laser desorption/ionization mass spectrometry for small molecule detection

A spherical vinyl-functionalized covalent-organic framework (COF-V) was prepared at room temperature by a facile method and applied as a novel substrate for surface-enhanced laser desorption/ionization mass spectrometry (SELDI-MS).

Small- and large-sized iron(II, III) oxide nanoparticles for surface-assisted laser desorption/ionization mass spectrometry of small biomolecules

RATIONALE

Common surface-assisted laser desorption/ionization (SALDI) surfaces are functionalized to improve mass spectrometric detection. Such surfaces are selective to certain group(s) of compounds. The application of universal and sensitive SALDI surfaces with appropriate size/surface area is paramount. In this study, two different sizes/surface areas of Fe3 O4 are compared as SALDI surfaces.

METHODS

For accurate surface area comparisons, the physical properties of the Fe3 O4 nanoparticles used as SALDI surfaces were determined using scanning electron microscopy, X-ray diffractometry, and N2 Brunauer-Emmet-Teller adsorption techniques. SALDI mass spectrometry (MS) data were acquired using a time-of-flight (TOF) mass spectrometer operated in the linear mode and equipped with a 50-Hz pulsed nitrogen laser (at 337 nm). Small biomolecules (adenosine, glucose, sucrose, tryptophan, and tripeptide) and a real sample (human serum) were analyzed.

RESULTS

The average sizes/specific surface areas of the SALDI surfaces of the small- and large-sized Fe3 O4 nanoparticles were ~21 nm/~82 m2 /g and ~39 nm/~38 m2 /g, respectively. An overall ~2.0-fold enhancement in signal-to-noise ratios was observed for the ionic species of the analyzed biomolecules in SALDI-MS using small-sized Fe3 O4 in comparison to large-sized Fe3 O4 nanoparticles. MS sensitivity from adenosine calibration curves (concentration between 0.05 and 10.0 mM) was ~2.0-fold higher for small-sized than large-sized Fe3 O4 nanoparticles as SALDI surfaces.

CONCLUSIONS

We have shown that transition-metal oxides such as Fe3 O4 nanoparticles are suitable and efficient surfaces for SALDI-TOF-MS analysis of small biomolecules. We observed improvement in signal-to-noise ratios and detection sensitivity for the analyzed samples from SALDI surfaces using small-sized (possessing larger surface area) than large-sized Fe3 O4 nanoparticles.

Gold nanoparticles for enhanced ionization and fragmentation of biomolecules using LDI-MS

New applications for gold nanoparticles (AuNPs) in laser desorption ionization mass spectrometry are presented here. This work expands on previous biomolecule studies and introduces carbohydrates, steroids, bile acids, and other small molecules as a focus. Broad trends in ionization are observed, and specifically of interest are new species that have not previously been reported from AuNPs (e.g., [M + Au]⁺ ). Interesting fragmentation effects have been observed for diphenhydramine, including similarity to electron impact mass spectra and possible radical driven reactions, providing insight into the mechanism of ionization when using AuNPs.

Current Technical Approaches for the Early Detection of Foodborne Pathogens: Challenges and Opportunities

The development of novel and high-tech solutions for rapid, accurate, and non-laborious microbial detection methods is imperative to improve the global food supply. Such solutions have begun to address the need for microbial detection that is faster and more sensitive than existing methodologies (e.g., classic culture enrichment methods). Multiple reviews report the technical functions and structures of conventional microbial detection tools. These tools, used to detect pathogens in food and food homogenates, were designed via qualitative analysis methods. The inherent disadvantage of these analytical methods is the necessity for specimen preparation, which is a time-consuming process. While some literature describes the challenges and opportunities to overcome the technical issues related to food industry legal guidelines, there is a lack of reviews of the current trials to overcome technological limitations related to sample preparation and microbial detection via nano and micro technologies. In this review, we primarily explore current analytical technologies, including metallic and magnetic nanomaterials, optics, electrochemistry, and spectroscopy. These techniques rely on the early detection of pathogens via enhanced analytical sensitivity and specificity. In order to introduce the potential combination and comparative analysis of various advanced methods, we also reference a novel sample preparation protocol that uses microbial concentration and recovery technologies. This technology has the potential to expedite the pre-enrichment step that precedes the detection process.

Dopamine-modified TiO2 monolith-assisted LDI MS imaging for simultaneous localization of small metabolites and lipids in mouse brain tissue with enhanced detection selectivity and sensitivity

Localization of metabolites using multiplexed mass spectrometry imaging (MSI) provides important chemical information for biological research. In contrast to matrix-assisted laser desorption/ionization (MALDI), TiO2-assisted laser desorption/ionization (LDI) for MSI improves detection of low molecular mass metabolites (<500 Da) by reducing matrix background. However, the low UV absorption of TiO2 nanoparticles and their ester hydrolysis catalytic activity hinder the detection of phospholipids and many low-abundance molecules. To address these challenges, we evaluated and optimized the material morphology and composition of TiO2. Dopamine (DA) was found to be an efficient ligand for TiO2, resulting in increased UV light absorption, higher surface pH, and formation of monolithic TiO2-DA structures. The sub-micron scale and higher surface pH of the TiO2 particle sizes led to improved detection of phospholipid signals. Compared to unmodified TiO2 sub-micron particles, the DA-modified TiO2 monolith led to 10- to 30-fold increases in the signal-to-noise ratios of a number of compound peaks. The TiO2-DA monolith-assisted LDI MSI approach has higher selectivity and sensitivity for Lewis basic compounds, such as fatty acids, cholesterols, ceramides, diacylglycerols, and phosphatidylethanolamine, when analyzed in positive mode, than traditional MALDI MS. Using this new method, over 100 molecules, including amino acids, alkaloids, free fatty acids, peptides, and lipids, were localized in mouse brain sections. By comparing the presence and localization of those molecules in young and old mouse brains, the approach demonstrated good performance in the determination of aging-related neurochemical changes in the brain.

Citric Acid Capped Iron Oxide Nanoparticles as an Effective MALDI Matrix for Polymers

A new matrix-assisted laser desorption ionization (MALDI) mass spectrometry matrix is proposed for molecular mass determination of polymers. This matrix contains an iron oxide nanoparticle (NP) core with citric acid (CA) molecules covalently bound to the surface. With the assistance of additives, the particulate nature of NPs allows the matrix to mix uniformly with polar or nonpolar polymer layers and promotes ionization, which may simplify matrix selection and sample preparation procedures. Several distinctively different polymer classes (polyethyleneglycol (PEG), polywax/polyethylene, perfluoropolyether, and polydimethylsiloxane) are effectively detected by the water or methanol dispersed NPCA matrix with NaCl, NaOH, LiOH, or AgNO₃ as additives. Furtheremore, successful quantitative measurements of PEG1000 using polypropylene glycol 1000 as an internal standard are demonstrated. Graphical Abstract ᅟ.

Enhanced Laser Desorption/Ionization Mass Spectrometric Detection of Biomolecules Using Gold Nanoparticles, Matrix, and the Coffee Ring Effect

Nanomaterials have been extensively used as alternate matrices to minimize the low molecular weight interferences observed in typical MALDI but such nanomaterials typically do not improve the spot-to-spot variability that is commonly seen. In this work, we demonstrate that nanoparticles and low matrix concentrations (<2.5 mg/mL) can be used to homogeneously concentrate analytes into a narrow ring by taking advantage of the "coffee ring" effect. Concentration of the samples in this way leads to enhanced signals when compared to conventional MALDI, with higher m/z analytes being enhanced to the greatest extent. Moreover, the ionization suppression often observed in samples with high salt concentrations can be overcome by preparing samples in this way. The ring that is formed is readily visible, allowing the laser to be focused only on spots that contain analyte. The coffee-ring effect represents a new mode by which nanomaterials can be used to enhance the MALDI-based detection of biomolecules.

Inkjet-printed gold nanoparticle surfaces for the detection of low molecular weight biomolecules by laser desorption/ionization mass spectrometry

Effective detection of low molecular weight compounds in matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) is often hindered by matrix interferences in the low m/z region of the mass spectrum. Here, we show that monolayer-protected gold nanoparticles (AuNPs) can serve as alternate matrices for the very sensitive detection of low molecular weight compounds such as amino acids. Amino acids can be detected at low fmol levels with minimal interferences by properly choosing the AuNP deposition method, density, size, and monolayer surface chemistry. By inkjet-printing AuNPs at various densities, we find that AuNP clusters are essential for obtaining the greatest sensitivity. Graphical Abstract ᅟ.

Use of flower-like gold nanoparticles in time-of-flight mass spectrometry

RATIONALE

Many kinds of nanoparticles (NPs) have been used for mass spectrometry (MS) so far. Here we report the first use of flower-like gold nanoparticles (AuNPs) as a mediator to enhance ionization in MS of peptides and proteins.

METHODS

Flower-like AuNPs were characterized using transmission and scanning electron microscopy, UV-VIS spectrophotometry, and laser desorption/ionization (LDI)-MS and compared with polyhedral AuNPs. Mass spectra were obtained in positive ion mode using a time-of-flight (TOF) analyzer coupled with either matrix-assisted laser desorption/ionization (MALDI) or surface-assisted laser desorption/ionization (SALDI) methods.

RESULTS

The intensities of peptide peaks (m/z 500-3500) were up to 7.5× and up to 7× higher using flower-like AuNPs and flower-like AuNPs-enriched α-cyano-4-hydroxycinnamic acid (CHCA) matrix respectively, than the classical CHCA matrix. The signals of higher mass peptide/protein peaks (m/z 3600-17000) were up to 2× higher with using flower-like AuNPs-enriched CHCA matrix than conventional CHCA matrix. The signal of profile peaks generated by intact cell MALDI-TOFMS of fibroblast suspension (m/z 4000-20000) was 2× higher with using flower-like AuNPs combined with sinapinic acid (SA) compared to SA matrix alone. The use of flower-like AuNPs as internal calibration standard for the calibration of MS spectra of peptides was performed.

CONCLUSIONS

Flower-like AuNPs and flower-like AuNPs combined with CHCA or SA as combined matrices for MS measurement of peptides and proteins were used. Comparison of the conventional MALDI method and our method with flower-like AuNPs was carried out. In addition, gold clusters generated from flower-like AuNPs by SALDI provide a suitable internal calibration standard for MS analysis of peptides. Copyright © 2015 John Wiley & Sons, Ltd.

Functional microgels assisted tryptic digestion and quantification of cytochrome c through internal standard mass spectrometry

Quantitation of cytochrome c (Cyt c) in cell lysates through surface-assisted laser desorption/ionization mass spectrometry (SALDI-MS) using gold nanoparticles (Au NPs) as the matrix and GR-10 peptide as an internal standard has been demonstrated. To shorten digestion time, temperature sensitive microgels containing trypsin (TR) and Au NPs have been employed. As-prepared functional microgels (TR/Au NPs/MGs) allow digestion of Cyt c within 15 s under microwave irradiation. The internal standard SALDI-MS approach provides linearity (R(2) = 0.98) of MS signal ratio (I 1168.6/I 1067.6) of the tryptic digested peptide (m/z 1168.6) to GR-10 peptide (m/z 1067.6) against the concentration of Cyt c ranging from 25 to 200 nM, with a limit of detection (at a signal-to-noise ratio of 3) of 10 nM. This approach has been validated by the analysis of the lysates of HeLa cells, with an average concentration of 13.7 ± 3.5 μM for cytoplasmic Cyt c. Increased concentrations of Cyt c in the HeLa cells treated with etoposide (a commercial drug) or carbon dots (potential drug) have been revealed through this simple, sensitive, and rapid SALDI-MS approach, supporting the drugs induced Cyt c-mediated apoptosis of the cells. This study has shown that this internal standard SALDI-MS approach holds great potential for cell study.

Nano/micro and spectroscopic approaches to food pathogen detection

Despite continuing research efforts, timely and simple pathogen detection with a high degree of sensitivity and specificity remains an elusive goal. Given the recent explosion of sensor technologies, significant strides have been made in addressing the various nuances of this important global challenge that affects not only the food industry but also human health. In this review, we provide a summary of the various ongoing efforts in pathogen detection and sample preparation in areas related to Fourier transform infrared and Raman spectroscopy, light scattering, phage display, micro/nanodevices, and nanoparticle biosensors. We also discuss the advantages and potential limitations of the detection methods and suggest next steps for further consideration.

Laser Desorption/Ionization Mass Spectrometry (LDI-MS) of Lipids with Iron Oxide Nanoparticle-Coated Targets

Iron oxide nanoparticle (NP)-coated target plates were employed for the direct detection and analysis of low molecular weight lipids by laser desorption/ionization (LDI) mass spectrometry (MS). We have demonstrated that the use of the iron oxide NP-coated target provides a simple, direct, and rapid detection method for lipid standards and epidermal surface lipids without any cumbersome sample pretreatment as well as mass spectra that are free of background matrix peaks. Lipid standards (1-stearoyl-sn-glycero-3-phosphocholine, 1,2-dioleoyl-sn-glycerol, 1-palmitoyl-2-oleoyl-3-linoleoyl-rac-glycerol, 1,2-distearoyl-sn-glycero-3-phosphocholine) were detected as either protonated or cationated species. Clean MS/MS spectra for each lipid were also successfully obtained. Pre-MS surface cleaning of the target plates with UV-ozone treatment successfully removed organic contaminants that would interfere with the mass spectra especially in the low molecular weight region. Preliminary application of the presented target plate to the detection of endogenous lipids in latent fingerprints showed promising results and for potential use in the visualization and chemical composition determination of latent fingerprints by nanoparticle assistance.

Sinapinic acid-directed synthesis of gold nanoclusters and their application to quantitative matrix-assisted laser desorption/ionization mass spectrometry

Core etching of gold nanoparticles (AuNPs) into smaller-sized clusters is a classic method for fabricating gold nanoclusters (AuNCs). The top down-based synthesis of AuNCs includes two steps: (i) reducing the Au(3+) precursor solution to generate AuNPs in the presence of protecting ligands and (ii) core etching of the formed AuNPs into the AuNCs via ligand exchange. For the first time, this paper describes a one-step approach for preparing AuNCs using a top down approach. The sinapinic acid (SA)-induced formation of the AuNCs involved a three-step reaction process. First, large AuNPs (>200 nm) were quickly formed after mixing SA and the Au(3+) precursor solution. Second, excess SA molecules self-assembled on the NP surface, and large AuNPs were etched to small AuNPs via electrostatic repulsion between the neighboring SA molecules. Finally, SA-induced core etching of the AuNPs resulted in the formation of the AuNCs within 70 min. Furthermore, we showed that the presence of the AuNCs in SA was capable of suppressing crystal growth and eliminating the coffee-ring effect. Thus, proteins can be successfully quantified using the SA-AuNCs as matrices for matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. Compared with using SA as matrices, the SA-AuNCs offered substantial advantages for improving shot-to-shot reproducibility and enhancing the ionization efficiency of proteins.

Matrix-assisted laser desorption/ionization, nanostructure-assisted laser desorption/ionization and carbon nanohorns in the detection of antineoplastic drugs. 1. The cases of irinotecan, sunitinib and 6-alpha-hydroxy paclitaxel

The development of surface-assisted laser desorption/ionization (SALDI) methodologies in mass spectrometry allows, in principle, the development of new analytical approaches to qualitative and quantitative measurements on small molecules. Some of these methods have been applied to characterize two antineoplastic drugs: irinotecan (1) and sunitinib (2), and also 6-α-hydroxy-paclitaxel (3), the main metabolite of paclitaxel. Three different SALDI approaches have been tested employing nanostructure- assisted laser desorption/ionization (NALDI), carbon nanohorns (NHs) and carbon nanohorns covered by liquid additives. The results so obtained have been compared to those observed under matrix-assisted laser desorption/ionization (MALDI) conditions. Compounds 1 and 2 show the easy formation of protonated molecular species under all the experimental conditions, but the highest absolute intensity was achieved by NALDI. On the contrary, ionic species of low intensity are present for 3, among which are those that exhibit the highest intensity caused by [M+K](+) ions. After a critical evaluation of the obtained data, the linear response of the [M+H](+) ion intensity of 1 versus different deposited sample amounts was investigated, and the best results (R(2) = 0.9889) were obtained under MALDI conditions. The analysis of plasma samples spiked with 1 showed, again, that the MALDI approach was the best one (R(2) = 0.9766). The failure of NALDI measurements could be rationalized by the presence of ion suppression effects.

Applications of nanomaterials in mass spectrometry analysis

Mass spectrometry (MS) based analyses have received intense research interest in a series of rapidly developing disciplines. Although current MS techniques have enjoyed great successes, several key challenges still remain in practical applications, especially for the detection of biomolecules in biological systems. The use of nanomaterials in MS based analysis provides a promising approach due to their unique physical and chemical properties. In this review, nanomaterials with different compositions and nanostructures employed in MS applications are summarised and classified by their functions. Such an integrated and wide reaching review will provide a comprehensive handbook to researchers with various backgrounds working in this exciting interdisciplinary area.

Semiconductor Nanomaterials-Based Fluorescence Spectroscopic and Matrix-Assisted Laser Desorption/Ionization (MALDI) Mass Spectrometric Approaches to Proteome Analysis

Semiconductor quantum dots (QDs) or nanoparticles (NPs) exhibit very unusual physico-chemcial and optical properties. This review article introduces the applications of semiconductor nanomaterials (NMs) in fluorescence spectroscopy and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) for biomolecule analysis. Due to their unique physico-chemical and optical properties, semiconductors NMs have created many new platforms for investigating biomolecular structures and information in modern biology. These semiconductor NMs served as effective fluorescent probes for sensing proteins and cells and acted as affinity or concentrating probes for enriching peptides, proteins and bacteria proteins prior to MALDI-MS analysis.

Layer-by-layer thin film of reduced graphene oxide and gold nanoparticles as an effective sample plate in laser-induced desorption/ionization mass spectrometry

This work demonstrated a simple platform for rapid and effective surface-assisted laser desorption/ionization time-of-flight mass spectrometry (SALDI-TOF MS) measurements based on the layer structure of reduced graphene oxide (rGO) and gold nanoparticles. A multi-layer thin film was fabricated by alternate layer-by-layer depositions of rGO and gold nanoparticles (LBL rGO/AuNP). The flat and clean two-dimensional film was served as the sample plate and also functioned as the matrix in SALDI-TOF MS. By simply one-step deposition of analytes onto the LBL rGO/AuNP sample plate, the MS measurements of various homogeneous samples were ready to execute. The optimization of MS signal was reached by the variation of the layer numbers of rGO and gold nanoparticles. Also, the small molecules including amino acids, carbohydrates and peptides were successfully analyzed in SALDI-TOF MS using the LBL rGO/AuNP sample plate. The results showed that the signal intensity, S N(-1) ratio and reproducibility of SALDI-TOF spectra have been significantly improved in comparison to the uses of gold nanoparticles or α-cyano-4-hydroxy-cinnamic acid (CHCA) as the assisted matrixes. Taking the advantages of the unique properties of rGO and gold nanoparticles, the ready-to-use MS sample plate, which could absorb and dissipate laser energy to analytes quite efficiently and homogeneously, has shown great commercial potentials for MS applications.

Mass spectrometry signal amplification for ultrasensitive glycoprotein detection using gold nanoparticle as mass tag combined with boronic acid based isolation strategy

We describe a novel method for rapid and ultrasensitive detection of intact glycoproteins without enzymatic pretreatment which was commonly used in proteomic research. This method is based on using gold nanoparticle (AuNP) as signal tag in laser desorption/ionization mass spectrometry (LDI-MS) analysis combined with boronic acid assisted isolation strategy. Briefly speaking, target glycoproteins were firstly isolated from sample solution with boronic acid functionalized magnetic microparticles, and then the surface modified gold nanoparticles were added to covalently bind to the glycoproteins. After that, these AuNP tagged glycoproteins were eluted from magnetic microparticles and applied to LDI-MS analysis. The mass signal of AuNP rather than that of glycoprotein was detected and recorded in this strategy. Through data processing of different standard glycoproteins, we have demonstrated that the signal of AuNP could be used to quantitatively represent glycoprotein. This method allows femtomolar detection of intact glycoproteins. We believe that the successful validation of this method on three different kinds of glycoproteins suggests the potential use for tracking trace amount of target glycoproteins in real biological samples in the near future.

Human serum albumin-modified Fe3O4 magnetic nanoparticles for affinity-SALDI-MS of small-molecule drugs in biological liquids

Here, we report on the use of human serum albumin (HSA)-modified Fe(3)O(4) nanoparticles (NPs) (HSA-Fe(3)O(4) NPs) for affinity-SALDI-MS of small drugs in human biological liquids. We demonstrated that HSA-Fe(3)O(4) NPs effectively captured small drugs from human urine and serum via the interactions between HSA and these drugs. The drugs adsorbed on HSA could then be identified by directly introducing the HSA-Fe(3)O(4) NPs into a mass spectrometer for SALDI-MS analysis. The ability of HSA to interact with multiple small drugs facilitated the simultaneous detection of a 4-drug-mixture in serum, viz., phenytoin, ibuprofen, camptothecin, and warfarin sodium, by affinity-SALDI-MS using HSA-Fe(3)O(4) NPs. In contrast, matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) with an organic matrix could detect only warfarin sodium. We also demonstrated the capacity of affinity-SALDI-MS to quantify warfarin sodium in urine samples across a range of 50 - 1000 μM (R(2) = 0.998) when using HSA-Fe(3)O(4) NPs. The detection sensitivity was further improved to a range of 5 - 100 μM (R(2) = 0.999) by using denatured HSA. The open structure of denatured HSA may enhance the effective extraction of small drugs from biological liquids, and increase the detection-sensitivity of affinity-SALDI-MS. Affinity-SALDI-MS using protein-modified Fe(3)O(4) NPs can open up new approaches to the analytical detection of small drugs in biological liquids by SALDI-MS.

Quantum dot applications endowing novelty to analytical proteomics

This review surveys all the state-of-art applications of quantum dots (QDs) in conventional and modern analytical methods in proteomic studies. A brief introduction of QDs and their properties is initially presented followed by outlining the application of QDs in fluorescence, MS, imaging, and cancer-based proteomics. The in-depth application of QDs in MALDI-MS and surface assisted laser desorption/ionization-MS has been elaborately discussed, summarizing the speculated mechanism behind the protein-QDs interactions during QD matrix applications leading to enhanced detection sensitivity.

Aptamer-conjugated multifunctional nanoflowers as a platform for targeting, capture, and detection in laser desorption ionization mass spectrometry

Although many different nanomaterials have been tested as substrates for laser desorption and ionization mass spectrometry (LDI-MS), this emerging field still requires more efficient multifuncional nanomaterials for targeting, enrichment, and detection. Here, we report the use of gold manganese oxide (Au@MnO) hybrid nanoflowers as an efficient matrix for LDI-MS. The nanoflowers were also functionalized with two different aptamers to target cancer cells and capture adenosine triphosphate (ATP). These nanoflowers were successfully used for metabolite extraction from cancer cell lysates. Thus, in one system, our multifunctional nanoflowers can (1) act as an ionization substrate for mass spectrometry, (2) target cancer cells, and (3) detect and analyze metabolites from cancer cells.

Signal enhancement in electrospray laser desorption/ionization mass spectrometry by using a black oxide-coated metal target and a relatively low laser fluence

The electrospray Laser desorption/ionization (ELDI) method is actively used for direct sample analysis and ambient mass spectrometry imaging. The optimizing of Laser desorption conditions is essential for this technology. In this work, we propose using a metal target with a black oxide (Fe3O4) coating to increase the signal in ELDI-MS for peptides and small proteins. The experiments were performed on an LTQ-FT mass spectrometer equipped with a home-made ELDI ion source. A cutter blade with black oxide coating was used as a target. A nitrogen laser was used with the following parameters: 337 nm, pulse duration 4ns, repetition rate 10 Hz, fluence to approximately 700 Jm(-2). More than a five times signal increase was observed for a substance P peptide when a coated and a non-coated metal target were compared. No ion signal was observed for proteins if the same fluence and the standard stainless steel target were used. With the assistance of the Fe3O4 coated metal target and a relatively low laser fluence < or =700 Jm(-2)), proteins such as insulin, ubiquitin and myoglobin were successfully ionized. It was demonstrated that the Fe3O4-coated metal target can be used efficiently to assist laser desorption and thus significantly increase the analyte signal in ELDI-MS. A relatively low laser fluence (< or = 700 Jm(-2)) was enough to desorb peptides and proteins (up to 17 kDal with the assistance of the Fe3O4-coated metal target under ambient conditions.

Fast nucleotide identification through fingerprinting using gold nanoparticle-based surface-assisted laser desorption/ionisation

We report a method centred on gold nanoparticle-based surface-assisted laser desorption/ionisation for analysis of deoxynucleotides and alkylated nucleobases. Gold nanoparticles allow for enhanced analysis capability by eliminating undesired signature peaks; thus more elegant mass spectra can be attained that allow identification by nucleotide mass fingerprint. The resulting fingerprinting patterns on the spectra are compared and associated with the presence of different nucleotides in the sample. This method can be easily extended to modified nucleotides implicated in genome lesions due to exposure to environment chemicals, such as DNA adducts (e.g. guanine adducts). The use of gold nanoparticles for surface-assisted laser desorption/ionisation can be an useful tool to resolve common issues of background noise when analysing nucleic acids samples.

Functionalized graphene-coated cobalt nanoparticles for highly efficient surface-assisted laser desorption/ionization mass spectrometry analysis

Graphene-coated cobalt nanoparticles surface-functionalized with benzylamine groups (CoC-NH(2) nanomagnets) were shown to effectively enrich analytes for surface-assisted laser desorption/ionization mass spectrometry (affinity SALDI-MS) analysis. These CoC-NH(2) nanomagnets are highly suited for use with affinity SALDI-MS because their mean diameter of 30 nm, high specific surface area of 15 m(2) g(-1), and high-strength saturation magnetization of 158 emu g(-1) led to efficient extraction of analytes by magnetic separation, which in turn enabled excellent SALDI-MS performance. Surface modification of CoC nanomagnets with benzylamine groups increased the yield of peptide ions and decreased fragmentation of benzylpyridinium ions, so-called "thermometer ions" formed through soft ionization. The CoC-NH(2) nanomagnets were used to extract perfluorooctanesulfonate from large volumes of aqueous solutions by magnetic separation, which was identified directly by SALDI-MS analysis with high sensitivity even at the sub-part-per-trillion level (∼0.1 ng/L). The applicability of CoC-NH(2) nanomagnets in conjunction with SALDI-MS for the enrichment and detection of pentachlorophenol, bisphenol A, and polyfluorinated compounds (PFCs) with varying chain length, which are environmentally significant compounds, as well as small drugs, was also evaluated.

Platinum vapor deposition surface-assisted laser desorption/ionization for imaging mass spectrometry of small molecules

RATIONALE

Matrix-assisted laser desorption/ionization (MALDI) imaging mass spectrometry (IMS) allows for the simultaneous detection and imaging of several molecules in a sample. However, when using an organic matrix in the MALDI-IMS of small molecules, inhomogeneous matrix crystallization may yield poorly reproducible peaks in the mass spectra. We describe a solvent-free approach that employs a homogeneously deposited metal nanoparticle layer (or film) for small-molecule detection.

METHODS

Platinum vapor deposition surface-assisted laser desorption/ionization imaging mass spectrometry (Pt vapor deposition SALDI-IMS) of small molecules was performed as a solvent-free and organic-matrix-free method. A commercially available magnetron sputtering device was used for Pt deposition. Vapor deposition of Pt produced a homogenous layer of nanoparticles over the surface of the target imaging sample.

RESULTS

The effectiveness of Pt vapor deposition SALDI-IMS was demonstrated for the direct detection of small analytes of inkjet ink on printed paper as well as for various other analytes (saccharides, pigments, and drugs) separated by thin-layer chromatography (TLC), without the need for extraction or concentration processes. The advantage of choosing Pt instead of Au in SALDI-IMS was also shown.

CONCLUSIONS

A solvent-free approach involving the direct deposition of Pt on samples (SALDI-IMS) is effective for the analysis of inkjet-printed papers and various analytes separated by TLC. This method would be useful in imaging analyses of various insulating materials such as polymers and biological materials.

Development of nanomaterials for SALDI-MS analysis in forensics

Within the last decade, the escalation of research output in the field of nanotechnology has spurred the development of new nanomaterials for use as assisting agents in surface assisted laser desorption ionization mass spectrometry (SALDI-MS). Specifically modified nanomaterials, coupled with mass spectrometry, have improved the detection sensitivity, specificity, flexibility and reproducibility of SALDI-MS analysis. The technological advancement of LDI-MS has in turn, propelled the use of the analytical technique in the field of forensics. In this report, the various roles and applications of metal-, silicon- and carbon-based nanostructured materials as SALDI matrices in the analysis of forensic samples are described. The advantages of SALDI-MS as an analytical tool for forensic sample analysis are also discussed.