Bonding to caries-affected dentin

Modified Experimental Adhesive with Sepiolite Nanoparticles on Caries Dentin Treated with Femtosecond laser and Photodynamic Activated Erythrosine. An invitro study

AIM

To assess the effect of CAD surface conditioners and their effect on Ra and SBS of tooth-colored filling material adhered to CAD surface with adhesive modified with 1 % Sep-NPs. Also, the DC of modified EA and its effect on the rheological properties.

METHODS

Ninety human molars with carious extension up to the middle third of occlusal dentin were included. The teeth were then arbitrarily allocated into three groups based on the type of surface conditioning received (n=30) Group 1 (PA), Group 2 (FS laser), and Group 3 (Ery PS). Ten samples from each group underwent Ra analysis using a stylus profiler. Twenty samples from each cohort were distributed into two subcategories based on the application of unmodified EA (A) and Sep-infiltrated EA (B). Composite restoration was built followed by SBS and failure mode analysis. Scanning electron microscopy and Energy dispersive X-ray EDX were assessed of sepiolite NPs. Degree of conversion (DC) and rheological analysis of the modified adhesive and unmodified adhesive were also performed. One-way analysis of variance (ANOVA) and the Tukey post hoc test were employed to conduct comparisons between the different groups RESULTS The highest score of Ra and bond strength were displayed by Group 1B (PA + Sep-NPs filled EA) (17.32 ± 1.43 MPa) samples. Nevertheless, the lowest values were established by Group 3A (Ery-PS + EA) (13.45 ±0.80 MPa) treated teeth. An increase in Ra resulted in a rise in SBS.DC decreased with the incorporation of 1% Sep-NPs in EA compared to unmodified EA.

CONCLUSION

Conditioning of CAD with PA and FS laser shows high surface roughness and favorable adhesion to experimental adhesive modified with 1% Sep-NPs. Modified adhesive with 1% Sep-NPs decreases DC and rheological properties.

An in-vitro evaluation of residual dentin retained after using novel enzymatic-based chemomechanical caries removal agents

To assess the biochemical, mechanical and structural characteristics of retained dentin after applying three novel bromelain-contained chemomechanical caries removal (CMCR) formulations in comparison to the conventional excavation methods (hand and rotary) and a commercial papain-contained gel (Brix 3000). Seventy-two extracted permanent molars with natural occlusal carious lesions (score > 4 following the International Caries Detection and Assessment System (ICDAS-II)) were randomly allocated into six groups (n = 12) according to the excavation methods: hand excavation, rotary excavation, Brix 3000, bromelain-contained gel (F1), bromelain-chloramine-T (F2), and bromelain-chlorhexidine gel (F3). The superficial and deeper layers of residual dentin were examined by Raman microspectroscopy and Vickers microhardness, while the surface morphology was assessed by the scanning electron microscope (SEM). A multivariate analysis of variance followed by Tukey's test (p > 0.05) was performed for data analysis. The novel formulations showed an ability to preserve the partially demineralized dentin that showed a reduced phosphate content with a higher organic matrix. This was associated with lower Vickers microhardness values in comparison to sound dentin and rotary excavation. The collagen integration ratio in all methods was close to sound dentin (0.9-1.0) at the deeper dentin layer. The bromelain-chloramine-T gel (F2) produced the smoothest smear-free dentin surface with a higher number of opened dentinal tubules. In contrast, dense smearing covering the remaining dentin was observed in the manual and rotary methods with obstructed dentin tubule orifices. The bromelain-contained formulations can be considered a new minimally invasive approach for selectively removing caries in deep cavitated dentin lesions.

Carbon nanotube-modified adhesive to caries affected dentin conditioned with Nd: YAP laser, Phosphoric acid, and Photoactivated-erythrosine

AIM

DENTIN CONDITIONED: with phosphoric acid (PA) Nd: YAP laser, and photoactivated-Ery(Erythrosine) on microleakage, shear bond strength (SBS) degree of conversion (DC), and rheological assessment of adhesive-infused with carbon nanotubes (CNTs).

MATERIAL AND METHOD

Carious ninety-six human mandibular molars were included. Specimens were disinfected and allocated into three groups based on surface pretreatment (n=32) Group 1 (PA), Group 2 (Nd: YAP) laser, and Group 3 (Photoactivated-Ery). Conditioned groups were further divided into two 2 subgroups based on the application of unmodified ERA and CNTs-modified ERA. Composite restorations were placed on the CAD surface and thermal aging of the samples was performed. The microleakage assessment was conducted using a dye penetration test. Universal testing machine (UTM) assessed SBS bond failure was evaluated using a stereomicroscope. Scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analyses of CNT, and Fourier Transform Infrared FTIR of adhesives were performed. One-way ANOVA and Tukey post hoc analyzed the outcomes.

RESULTS

Group 1B samples (PA+ CNTs modified adhesive) presented the minimum marginal leakage and highest bond integrity. Group 2A (Nd:YAP laser+Unmodified adhesive) displayed the maximum scores of microleakage and lowest bond strength.

CONCLUSION

Photoactivated Ery-PS can serve as an alternative to phosphoric acid for conditioning CAD. Incorporating CNT in adhesive significantly enhanced bond integrity and marginal seal with no significant difference in DC.

Exploring the role of flavonoids in caries-affected dentin adhesion: A comprehensive scoping review

OBJECTIVES

The aim of this scoping review was to evaluate the available scientific evidence regarding the use of flavonoids in the treatment of caries-affected dentin focusing on bonding to dentin.

METHODS

A comprehensive literature search was performed in five databases from March 2022 and updated in April 2023: PubMed, EMBASE, Scopus, Web of Science, and Scielo. Additionally, the references of included studies were manually searched. Gray literature was excluded from the review.

STUDY SELECTION

Inclusion criteria included in vitro, in situ, and in vivo studies (animal or human) published in English. Abstracts, reviews, case reports, book chapters, doctoral dissertations, guidelines, and studies using pure plant extracts were excluded. Data collected from the selected studies were summarized and subjected to narrative and descriptive analysis. Out of the 91 studies identified, only 16 studies met the inclusion criteria.

RESULTS

The review analyzed eight different flavonoids (hesperidin, galardin, proanthocyanidin, genipin, quercetin, naringin, epigallocatechin-3-gallate, and other catechins subtypes) used as pretreatment or loaded into adhesive systems, primers, and phosphoric acid. The use of flavonoids improved the mechanical properties of the materials and modified the biological properties of the dentin, reducing collagen loss by the inhibition of proteolytic activity of matrix metalloproteinases (MMPs).

CONCLUSIONS

Based on the findings of this scoping review, it can be concluded that the use of flavonoids as pretreatment or incorporation into dental materials preserves collagen in the hybrid layer, inhibiting the MMPs activities, modifying the collagen fibrils of the dentin matrix and improving the mechanical properties of the dental adhesive systems. Therefore, it represents a promising approach for promoting dentin biomodification. This can result in more stable bonding of adhesive restorations to caries-affected dentin.

Effect of Casein Phosphopeptide-Amorphous Calcium Phosphate, Proanthocyanidin, Carbon Dioxide Laser Remineralization on the Bond Integrity of Composite Restoration Bonded to Caries-Affected Dentin

Objective: Assessment of different remineralizing pretreatment casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), proanthocyanidin (PA), carbon dioxide laser (CO2), eggshell solution (ES) on the shear bond strength (SBS) of resin composite bonded to remineralized carious-affected dentin (CAD). Materials and methods: Eighty human molars were collected with occlusal caries that extended about halfway into the dentin. Using a water-cooled, low-speed cutting saw, a flat, mid-coronal dentin surface was exposed. CAD was differentiated from healthy dentin. Based on the remineralizing agent used on the CAD surface, the teeth were arbitrarily allocated into five groups (n = 10). Group 1: no remineralizing agent, Group 2: CPP-ACP, Group 3: 6.5% PA solution, Group 4: CO2 laser, and Group 5: ES solution. All samples were bonded to composite and light cured and thermocycled. SBS and failure mode analysis were performed using universal testing and stereomicroscope 40 × . Using SPSS, SBS, and failure mode data were analyzed using analysis of variance and Tukey's honesty significant difference (HSD) test Results: Group 3 (6.5% PA solution; 15.59 ± 1.44 MPa) samples established the maximum bond integrity. Nevertheless, Group 1 (No remineralizing agent; 11.19 ± 1.21 MPa) exhibited the minimum outcome of bond strength. Intergroup comparison analysis showed that Group 1 (No remineralizing agent), Group 2 (CPP-ACP), and Group 4 (CO2 laser) established comparable values of bond strength (p > 0.05). Likewise, Group 3 (6.5% PA solution) and Group 5 (EA solution) also revealed equivalent bond integrity (p > 0.05). Conclusions: PA and ES are considered potential remineralizing agents used for caries-affected dentin surfaces in improving bond integrity to composite resin. However, further studies are advocated to extrapolate the findings of this study.

Assessment of physical properties of bioactive glass-modified universal multimode adhesive and its bonding potential to artificially induced caries affected dentin

BACKGROUND

To evaluate the physical properties of bioactive glass-modified universal multimode adhesive and its micro-tensile bond strength (µTBS) to artificially induced caries-affected dentin.

METHODS

All bond universal adhesive was used in the study. Specimens were divided into 2 main groups: control unmodified adhesive and 5 wt% BAG modified adhesive. The degree of conversion, pH, bioactivity, and viscosity of the adhesives were tested with n = 5 for each test. Micro-tensile bond strength evaluation was done in etch & rinse (ER) and selective-etch (SE) modes, where 24 human molar teeth were used (n = 3), 12 teeth for immediate bond strength, and the other 12 were tested after 6 months of storage in simulated body fluid (SBF).

RESULTS

No significant difference was found between the control and the 5wt% BAG groups regarding the degree of conversion (61.01 ± 0.43 and 60.44 ± 0.61 respectively) and the viscosity (109.77 ± 22.3 and 124.3 ± 9.92 respectively). The control group revealed significantly lower pH values than the 5wt% BAG group (3.16 ± 0.5 and 4.26 ± 0.09 respectively). Immediate bond strength results revealed that the 5wt% BAG in the ER mode had the highest bond strength followed by the control group in the ER mode (44.16 ± 7.53 and 44.00 ± 7.96 respectively). SE groups showed that the immediate strength of the 5wt% BAG group was higher than the control group (42.09 ± 6.02 and 39.29 ± 6.64 respectively). After 6 months of storage, bond strength results revealed a decrease in bond strength values for the control groups but not for the 5wt% BAG in both application modes.

CONCLUSIONS

The incorporation of BAG (5wt%) improved the universal adhesive micro-tensile bond strength and bond durability for both adhesive application modes without affecting its degree of conversion or viscosity.

Mechanical properties of simulated dentin caries treated with metal cations and L-ascorbic acid 2-phosphate

This pH cycling study aimed to investigate the effects of L-Ascorbic acid 2-phosphate (AA2P) salts of Mg, Zn, Mn, Sr, and Ba on the surface microhardness, compressive strength, diametral tensile strength (DTS), and solubility of root canal dentin. 186 cylindrical dentin specimens from 93 teeth were fortified with optimal concentrations of AA2P salts of Mg (0.18 mM), Zn (5.3 µM), Mn (2.2 × 10-8 M), Sr (1.8 µM), and Ba (1.9 µM). Saline was used as the control group. These dentin specimens underwent a 3-day cycling process simulating dentin caries formation through repeated sequences of demineralization and remineralization. Surface microhardness at 100 and 500 µm depths (n = 10/subgroup), scanning electron microscopy (n = 3/group), compressive strength (n = 10/group), DTS (n = 6/group), and solubility (n = 5/group) tests were performed to analyze the dentin specimens. Data were analyzed using Kolmogorov-Smirnov, one-way ANOVA, and Post Hoc Tukey tests (p < 0.05). The control group had significantly lower microhardness at both depths (p < 0.001), reduced DTS (p = 0.001), decreased compressive strength (p < 0.001), and higher weight loss (p < 0.001) than all other groups. The Sr group had the highest compressive strength and microhardness among all the groups. The microhardness was significantly higher for the 500 µm depth than the 100 µm depth (p < 0.001), but the difference in microhardness between depths across groups was not significant (p = 0.211). All fortifying solutions provided some protection against artificial caries lesions. Therefore, these elements might have penetrated and reinforced the demineralized dentin against acid dissolution.

Adhesive Bond Strength of Restorative Materials to Caries-Affected Dentin Treated with Antimicrobial Photodynamic Therapy: A Systematic Review and Meta-Analysis

Objective: This systematic review aimed to evaluate the adhesive bond strength of restorative materials to caries-affected dentin (CAD) treated with antimicrobial photodynamic therapy (aPDT) in comparison with conventional chemical disinfectants. Methods: Three databases, including the Web of Science, Scopus, and PubMed, were searched to address the focused question: "What is the effect of aPDT compared to conventional chemical disinfection techniques on the adhesive bond strength of restorative materials to CAD?." Search keywords included "dentin*" "adhes bond*" "caries-affected dentin" "photodynamic "photochemotherapy" "photosensitizing agent" "phototherapy" "photoradiation" "laser" "light activated" "photoactivated." A fixed-effects model was used in each meta-analysis and the inverse variance was used to calculate the standard mean difference (SMD). For evaluating the statistical heterogeneity, the Cochrane's Q test and the I2 statistics were used. The risk of bias was evaluated based on the Cochrane Collaboration's tool. Results: Fourteen studies were included in the qualitative as well as quantitative analysis. The results of the meta-analyses exhibited an SMD of 2.38% [95% confidence interval (CI): 2.03-2.73; p < 0.00001], indicating a statistically significant difference in the shear bond strength scores between the tested group (samples treated with aPDT) and the control group (i.e., favoring the sound dentin and/or conventional chemical disinfectants). Contrarily, an SMD of -1.46% (95% CI: -2.04 to -0.88; p < 0.00001) and -0.37% (95% CI: -0.70 to -0.03; p = 0.03) was observed, indicating a statistically significant difference in the microtensile bond strength (μTBS), as well as microleakage scores between the tested group (favoring the samples treated with aPDT) and the control group (i.e., sound dentin and/or conventional chemical disinfectants). Conclusions: Adhesive bond strength of restorative materials to CAD treated with conventional chemical disinfectants showed superior outcomes compared to photodynamic therapy (aPDT).

Effect of limonene associated with bioactive glass-ceramic on dentin/adhesive interface

This study evaluated the effect of pretreatment with limonene and/or biosilicate on the bond strength of a universal adhesive system in self-etch mode to dentin. Occlusal cavities were prepared in 80 human molars and the teeth were randomly allocated to one of four groups (n = 20), according to the pretreatment regimens applied before the adhesive. The pretreatments were (i) Control, no pretreatment, (ii) LIM, 0.5% limonene; (iii) Bio, 10% biosilicate; and (iv) LIMBio, LIM + Bio. After adhesive application and restoration, the specimens were sectioned into sticks, separated, and stored in distilled water at 37°C for 24 h or 6 months. Microtensile bond strength test was carried out and measurements were compared across pretreatment groups and storage times. Fracture patterns and adhesive interfaces were observed. Loss of dry mass was calculated (n = 10). There was no statistically significant difference in the bond strength between the groups and the most prevalent fracture pattern was the non-adhesive. LIM and LIMBio resulted in more open dentinal tubules. LIM and Bio, whether separate or combined, showed particles of those substances, which decreased in size and number after 6 months. All groups lost mass weight after treatment, with no statistically significant differences between them. Limonene and biosilicate pretreatment did not affect the bond strength to dentin of the universal adhesive system, but resulted in more non-adhesive fractures, even after 6 months.

Dentin disinfection and adhesive bond strength using modified photoactivated carbon nanoparticles

AIMS

The present study aimed to investigate the bond integrity and disinfection efficacy of Methylene blue(MB) alone, MB-PDT (Photodynamic therapy), MB@ carbon nanoparticles (CP)-PDT, and Cr, Cr: YSGG (ECL) against lactobacilli in Caries-affected dentin (CAD) MATERIAL AND METHODS: Methods consisted of Shear bond strength (SBS), Scanning electron microscopy (SEM), energy dispersive X-ray (EDX), methods of disinfection, and failure analysis. CAD samples were prepared and biofilm formed on the specimens randomly allocated into five groups based on disinfection. Group 1: CHX; Group 2: MB; Group 3: MB-PDT: group 4: MB@CP-PDT and group 5: ECL. After disinfection Colony forming units were measured and specimens were restored and positioned under a universal testing machine (UTM). Failure analysis was performed using a stereomicroscope. The difference in survival rate was assessed using the Kruskal-Walis test. Mean and standard deviation for bond values after different methods of disinfection was evaluated using analysis of variance (ANOVA) and Post Hoc Tukey. The significance level was p<0.05 RESULTS: Morphological analysis revealed that CPs under SEM are flat discs with edged irregular shapes. EDX analyses show a spike indicating carbon particles by more than 95%. MB@CP-PDT displayed the highest reduction in lactobacillus levels in comparison to the other disinfection methods. The highest SBS was exhibited by the CAD sample disinfected with ECL. The lowest SBS values in CAD specimens after cavity cleansing with MB alone. The predominant failure type in CAD disinfected with MB alone, ECL CHX, MB-PDT, and MB@CP-PDT was adhesive.

CONCLUSION

The use of MB@CP-PDT showed high antibacterial potency against lactobacillus but demonstrated bond values similar to CHX. Use of Er, Cr: YSGG showed considerable effectiveness against lactobacillus along with the highest bond values.

Efficacy of methylene blue and curcumin mediated antimicrobial photodynamic therapy in the treatment of indirect pulp capping in permanent molar teeth

PURPOSE

This study aimed to evaluate the adhesive bond strength and antibacterial efficacy of methylene blue (MB)-mediated antimicrobial photodynamic therapy (aPDT) and curcumin (CUR)-mediated aPDT versus the conventional disinfectants, such as chlorhexidine gluconate (CHX) gel and sodium hypochlorite (NaOCl), for indirect pulp capping (IPC) treatment of permanent molars.

METHODS

One Hundred grossly carious human permanent molars were collected through non-traumatic extraction. All specimens were embedded in polyvinyl cross-sections to the cemento-enamel junction. The cavity preparation was conducted by grinding the samples using silicon carbide discs. After culturing Streptococcus mutans (S. mutans), a 10 µL of S. mutans suspension (10⁶ colony forming units/mL) was transferred in each tooth cavity and anaerobically incubated for 48 hours at 37°C. All specimens were randomly divided into 5 groups: Group-I: samples treated IPC; Group-II: samples treated with 2% CHX gel; Group-III: samples treated with 6% NaOCl; Group-IV: irradiation of prepared cavity with MB-mediated aPDT; and Group-V: irradiation of prepared cavity with CUR-mediated aPDT. After disinfection methods, the universal adhesive was used, and all specimens were restored using giomer. Eventually, confocal laser scanning microscopy, shear bond strength (SBS), micro-tensile bond strength (μTBS), four-point bending strength (4P-BS) analyses were performed, and the data were analyzed statistically.

RESULTS

At baseline, the highest SBS (48.8 ± 6.5 MPa), μTBS (54.3 ± 3.9 MPa), and 4P-BS (123 ± 32 MPa) scores were demonstrated by the samples treated with MB-mediated aPDT. However, after 12 months of storage, the highest SBS (42.3 ± 3.9 MPa) and μTBS (45.2 ± 6.6 MPa) scores were shown by samples treated with MB-mediated aPDT, while CUR-mediated aPDT treated samples demonstrated the highest 4P-BS scores (70 ± 18 MPa). Moreover, the highest antibacterial activity against S. mutans was shown by the samples treated with MB-mediated aPDT.

CONCLUSIONS

The application of aPDT, especially MB-mediated, demonstrated superior SBS, μTBS, and 4P-BS values as well as antibacterial activity against S. mutans as compared to 2% CHX gel and 6% NaOCl as cavity disinfectants for IPC treatment of permanent molars.

Clinical applications of antimicrobial photodynamic therapy in dentistry

Given the emergence of resistant bacterial strains and novel microorganisms that globally threaten human life, moving toward new treatment modalities for microbial infections has become a priority more than ever. Antimicrobial photodynamic therapy (aPDT) has been introduced as a promising and non-invasive local and adjuvant treatment in several oral infectious diseases. Its efficacy for elimination of bacterial, fungal, and viral infections and key pathogens such as Streptococcus mutans, Porphyromonas gingivalis, Candida albicans, and Enterococcus faecalis have been investigated by many invitro and clinical studies. Researchers have also investigated methods of increasing the efficacy of such treatment modalities by amazing developments in the production of natural, nano based, and targeted photosensitizers. As clinical studies have an important role in paving the way towards evidence-based applications in oral infection treatment by this method, the current review aimed to provide an overall view of potential clinical applications in this field and summarize the data of available randomized controlled clinical studies conducted on the applications of aPDT in dentistry and investigate its future horizons in the dental practice. Four databases including PubMed (Medline), Web of Science, Scopus and Embase were searched up to September 2022 to retrieve related clinical studies. There are several clinical studies reporting aPDT as an effective adjunctive treatment modality capable of reducing pathogenic bacterial loads in periodontal and peri-implant, and persistent endodontic infections. Clinical evidence also reveals a therapeutic potential for aPDT in prevention and reduction of cariogenic organisms and treatment of infections with fungal or viral origins, however, the number of randomized clinical studies in these groups are much less. Altogether, various photosensitizers have been used and it is still not possible to recommend specific irradiation parameters due to heterogenicity among studies. Reaching effective clinical protocols and parameters of this treatment is difficult and requires further high quality randomized controlled trials focusing on specific PS and irradiation parameters that have shown to have clinical efficacy and are able to reduce pathogenic bacterial loads with sufficient follow-up periods.

Bonding strategies to deal with caries-affected dentin using cross-linking agents: Grape seed extract, green tea extract, and glutaraldehyde - An in vitro study

Aim

This study evaluated the effect of three collagen cross-linking agents - proanthocyanidins (grape seed extract [GSE] and green tea extract [GTE]) and glutaraldehyde [GA] on microshear bond strength (μSBS) of caries-affected dentin (CAD)-resin complex.

Materials and Methods

Freshly extracted 96 teeth with caries up to the middle third of dentin were sectioned through the deepest part of the occlusal fissure, perpendicular to the long axis of the crown. Caries was excavated with large round bur until firm dentin was obtained, confirmed by visual inspection and tactile examination. Flat occlusal dentin surfaces were treated as follows: Group-1 - 6.5% GSE (n = 30), Group-2 - 2% GTE (n = 30), Group-3 - 5% Glutaraldehyde (n = 30), Group-4 - control group (no agents) (n = 6). Each group was further divided into Subgroup A - Etch-N-Rinse 15s, Subgroup B - Etch-N-Rinse 45s, and Subgroup C - Self-etch. Two increments of 1.5-mm thick composite (Tetric-N-Ceram - Ivoclar Vivadent) with a 1-mm diameter were built-up. Each sample was subjected to μSBS test in Universal Testing Machine. Student's t-test was done for intragroup comparison and one-way ANOVA for intergroup comparison.

Results

Statistically significant difference was present in mean μSBS, with Group 1B showing the best results and Group 4C, the least.

Conclusions

Thus, the application of these collagen cross-linkers, to CAD, increases μSBS and promises a new approach to improve dentin bond strength.

Assessment of Caries-Affected Dentin Adhesive Interface Treated with Contemporary Conditioning Techniques

Objective: The aim of this study was to assess shear bond strength (SBS) and failure analysis of adhesion of composite resin (CR) to caries-affected dentin (CAD) pretreated with the Er,Cr:YSGG (ECY) laser, photodynamic therapy (PDT), and etch and rinse (ER) used for cavity disinfection. Materials and methods: Methods used in this study included scanning electron microscopy (SEM), SBS analysis, failure analysis, and digital microscopy. The methods were adopted to assess bond integrity, CAD interface, smear layer, and hybridization. Thirty human third molars assessed clinically and having scores of 4 and 5 based on International Caries Detection and Assessment System (ICDAS) criteria were inspected. Infected dentin was removed. Dentin that was hard and stained pink was categorized as CAD. Ten samples were used in each group for pretreatment of CAD. Ten samples of healthy dentin [sound dentin (SD)] were collected separately and taken as controls. Samples were divided into the following groups: group 1: SD+ER; group 2: CAD+ER; group 3: CAD+ECY; and group 4: CAD+PDT after the pretreatment bonding agent was applied and the restorative procedure was performed using CR. Results: CAD conditioned with PDT before bonding to CR demonstrated the lowest SBS values (11.22 ± 0.77 MPa), whereas the highest SBS values were observed in the SD surface treated with ER (18.25 ± 1.22 MPa). In CAD and SD pretreated with ER, majority of failure modes were cohesive failure and admixed failure, whereas in CAD pretreated with PDT and the ECY laser, the adhesive failure mode was pertinent. Conclusions: The use of the ECY laser and PDT on CAD for cavity disinfection does not have potential for application in clinical settings as it decreases bond integrity of CR. Moreover, the ER pretreatment method for CAD and SD remains the gold standard.

Riboflavin (Vitamin B2), Turmeric (Curcumin) Photosensitizers Mediated Photodynamic Therapy, and Er, Cr: YSGG on Microleakage of Class V Cavities Restored by Resin-Modified Glass-Ionomer Cement

Purpose: The present study aimed to assess the effect of RF and CP intervened PDT and Er, Cr: YSGG laser on microleakage in class V RMGIC restorations in permanent teeth. Materials and Methods: In-vitro eighty standardized class V cavities (4×4×2) were prepared in extracted permanent molars based on ICDAS II (International Caries Detection and Assessment System II) caries severity code 0. All samples were arbitrarily alienated into four groups: Group 1, PDT mediated riboflavin photosensitizer (RF) [concentration of 150 μg/mL]; Group 2, PDT with curcumin photosensitizer (CP) [concentration of 100 μg/mL]; Group 3, Er, Cr: YSGG laser application; Group 4, control group: rinsed and dried dentin. Cavities were restored with conventional RMGIC. The specimens were immersed in 0.5% Fuchsine solution for 24 hrs. and sectioned. Microleakage scores were assessed under a microscope. Intergroup and intragroup comparisons were made at enamel and cementum margin respectively. Data were analyzed by non-parametric Kruskal-Wallis test and Wilcoxon tests at the level of significance deemed p < 0.05. Results: Riboflavin and curcuminmediated PDT would produce a superior reduction (95% viz 90%) of microleakage as compared to Er, Cr: YSGG laser (85%), and no control groups. Cu-PDT observed the highest amount of microleakage with the least amount of microleakage in the control group. Conclusion: Riboflavin and curcumin photosensitizers mediated PDT and Er, Cr: YSGG laser has the potential to be utilized in class V cavities before RMGIC restorations at enamel margins without adversely affecting the marginal integrity.

Evaluation of the Effect of the Loading Time on the Microtensile Bond Strength of Various Restorative Materials Bonded to Silver Diamine Fluoride-Treated Demineralized Dentin

The aim of this study was to evaluate the effect of immediate versus delayed loading times on the microtensile bond strength (μTBS) of restorative materials, including resin-based composite (RBC), resin-modified glass ionomer cement (RMGIC) and glass ionomer cement (GIC), that were bonded to silver diamine fluoride (SDF)-treated demineralized dentin. Ninety caries-free extracted premolar teeth were assigned to three groups (n = 30) loaded with RBC, RMGIC and GIC restorative materials. Each group was further divided into three subgroups (n = 10): subgroup A (control specimens), immediate loading of the restorative material on sound dentin; subgroup B, demineralized dentin, SDF treatment and immediate loading of the restorative material; and subgroup C, demineralized dentin, SDF treatment and restorative material loading a week later. One-way ANOVA and Tukey’s post-hoc tests were performed to compare the μTBS values. The RBC exhibited the highest µTBS, followed by RMGIC and GIC. Multiple comparisons showed an increase in the µTBS in the delayed loading groups irrespective of the restorative material used. The majority of the failure modes were adhesive. Delayed loading of RMGIC for 1 week after SDF application showed significantly higher µTBS than that of immediate loading.

Disinfection of caries-affected dentin using activated vitamin B2 and diode laser with total-etch technique. An assessment of adhesive bond

AIM

The present study aims to evaluate the bond integrity of composite restoration bonded to CAD after disinfection using pineapple peel extract (PPE) Diode laser (DL) and riboflavin (RF) activated by photodynamic therapy (PDT).

MATERIAL AND METHODS

Forty human permanent mandibular molars were collected, disinfected, and mounted in poly-vinyl pipes. Carious infected dentin was removed and CAD was disinfected. Samples were divided into 4 groups based on disinfection. Group 1: CAD disinfected with CHX; group 2: CAD disinfected with diode laser; CAD disinfected with PPE and CAD sterilized with riboflavin. Following disinfection, CAD surfaces were applied with the etch-and-rinse adhesive system and bonding agent and restored with a composite restoration. Samples were placed in a thermocycler to simulate oral aging and then mounted on the universal testing machine (UTM) for shear bond strength (SBS) testing. Failure mode was assessed using a steriomicroscoscope at 40X magnification. One-way analysis of variance (ANOVA) compared the mean SBS and failure type obtained to identify intergroup differences. Similarly, for multiple group comparison, the Tukey HSD test was used keeping the level of significance at 0.05 RESULTS: : CAD disinfected with chlorhexidine (CHX) established the highest bond integrity of the restoration. However, group 2 CAD disinfected with DL displayed the lowest bond values. It was also observed that dentin disinfected using CHX demonstrated comparable SBS values to CAD disinfected with PPE and CAD disinfected with RF.

CONCLUSION

RF and PPE displayed comparable outcomes of SBS of composite restoration bonded to CAD to that of CHX. DL displayed lower bond integrity than the other investigated groups. Further studies are recommended to deduce the findings of the existing study.

Addition of metal chlorides to a HOCl conditioner can enhance bond strength to smear layer deproteinized dentin

OBJECTIVES

To evaluate the effect of smear layer deproteinization using hypochlorous acid (HOCl) with/without metal chlorides (SrCl₂ and ZnCl₂) on the microtensile bond strength (µTBS) of two simplified adhesives to dentin.

METHODS

Human dentin surfaces with a standardized smear layer were pretreated using a 105 ppm HOCl solution with/without SrCl₂ (0.05 M, 0.1 M, 0.2 M, 0.4 M) or ZnCl₂ (0.05 M, 0.1 M, 0.2 M) for 5 s, 15 s, or 30 s. After the deproteinizing solution was washed out with water for 5 s, 15 s, or 30 s, pretreated surfaces were bonded with one-step self-etch adhesive Bond Force II or universal adhesive Clearfil Universal Bond Quick, and µTBS was measured after 24 h. Additionally, the deproteinizing effects of HOCl solutions with/without the metal chlorides were compared by measuring changes in the amide:phosphate ratio using attenuated total reflection Fourier transform infrared spectroscopy. Statistical analysis was performed using multifactor ANOVA, Tukey's post hoc tests and t-tests (p < 0.05).

RESULTS

Pretreatment with pure HOCl for 15 s and 30 s significantly decreased the amide:phosphate ratio (p < 0.05), indicating effective deproteinization, but the µTBS of both adhesives increased significantly only if HOCl was washed out for 30 s (p < 0.05). Increasing the concentrations of metal chlorides enabled shortening of the wash-out time down to 5 s while maintaining the improved µTBS (p < 0.05). The deproteinizing effect of HOCl was not significantly altered by the addition of metal chlorides (p > 0.05).

SIGNIFICANCE

The effectiveness of smear layer deproteinization using HOCl can be improved by the addition of metal chlorides, as their increasing concentration allowed to shorten the wash-out time from 30 s down to 5 s.

Disinfection of caries affected dentin using Rose Bengal, Titanium Sapphire Laser; Ammonium Hexa-fluorosilicate, and ozonated water on resin dentin bond strength

AIM

The present study intended to evaluate the shear bond strength (SBS) of resin cement bonded to caries affected dentin (CAD) after disinfection with rose Bengal (RB), Ti-Sapphire Laser, Ammonium Hexafluorosilicate (NH₄)₂[SiF₆], and ozonated water (O₃) MATERIAL AND METHODS: A total of 100 extracted human mandibular molars were acquired using caries severity code, 6 of the ICDAS criteria. To achieve homogeneity and prevent size-biased distributions, the average cavity preparation of all specimens had a depth of 2 mm and a breadth of 3 mm. Specimens were divided into five groups (n = 20) at random according to type of disinfection. Group 1: control group, Group 2: RB, Group 3: O₃, Group 4: Ti-sapphire laser, and Group 5: (NH4)2[SiF₆]. All specimens were etch and rinsed, bonding agent was applied and restored with resin cement. Estimation of SBS was performed by placing samples (10/group) in universal testing machine. Stereomicroscope under 40 × magnification was employed for failure mode analysis (FMA). Statistical analysis was executed using the ANOVA and the Tukey multiple test (p<0.05).

RESULTS

The highest SBS was demonstrated in the control group when CAD bonded to resin cement without disinfection (18.22±1.14 MPa). Likewise, the lowest SBS values were unveiled by CAD disinfection with O₃ (12.44±1.36 MPa). Similarly, CAD when disinfected with RB (16.25±1.01 MPa) and Ti-sapphire laser (16.25±1.22 MPa) bonded to resin cement exhibited comparable bond results (p>0.05).

CONCLUSION

Caries affected dentin when treated with etch and rinse technique without the use of disinfectant displayed the highest SBS. However, it was seen that utilization of various disinfectants has altered the adhesion capacity or bonding efficacy of caries-affected dentin.

The effect of fluoride iontophoresis on seal ability of self-etch adhesive in human dentin in vitro

Background

Fluoride iontophoresis (FI) is a non-invasive method for the transfer of fluoride ions under electrical pressure into dental hard tissue. This study aimed to determine the effect of FI on the seal ability of self-etch adhesive in human dentin using dentin permeability test and scanning electron microscopy (SEM).

Methods

The experiments were divided into 2 series: series 1 was performed on 28 extracted intact third molars and series 2 was performed on 28 extracted carious third molars (ICDAS 4 and 5). In each series, 20 teeth were used for dentin permeability test and 8 teeth were used for SEM study. For dentin permeability test, the specimens were divided into dentin without FI (control) and dentin with FI (experimental) subgroups. Hydraulic conductance (HD) of dentin was measured before and after adhesive treatment, and calculated for the percentage decrease of HD in each subgroup. Two-way ANOVA and Tukey test were used for statistical analysis. SEM study was used to assess the seal ability of self-etch adhesive and penetration of fluoride ions into dentinal tubules.

Results

HD after self-etch adhesive treatment reduced by 57.75 ± 17.99% in intact dentin with FI, 46.60 ± 17.03% in intact dentin without FI, 45.00 ± 15.30% in caries affected dentin without FI, and 37.28 ± 14.72% in caries affected dentin with FI. There was no significant difference in percentage decrease of HD between dentin without FI and dentin with FI (P = 0.742); meanwhile, intact dentin with FI had significant greater percentage decrease than caries affected dentin with FI (P < 0.05). SEM findings showed FI produced more particle formation and deeper precipitation in intact dentin than those in caries affected dentin.

Conclusions

FI did not affect the seal ability of self-etch adhesive in human dentin when compared to without FI. However, FI could augment the seal ability of the self-etch adhesive in intact dentin better than that in caries affected dentin.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12903-022-02146-w.

Dentin collagen denaturation status assessed by collagen hybridizing peptide and its effect on bio-stabilization of proanthocyanidins

OBJECTIVE

To assess dentin collagen denaturation from phosphoric acid and enzyme treatments using collagen hybridizing peptide (CHP) and to investigate the effect of collagen denaturation on bio-stabilization promoted by proanthocyanidins (PA).

METHODS

Human molars were sectioned into 7-µm-thick dentin films, demineralized, and assigned to six groups: control with/without PA modification, H₃PO₄-treated collagen with/without PA modification, enzyme-treated collagen with/without PA modification. PA modification involved immersing collagen films in 0.65% PA for 30 s. H₃PO₄ and enzyme treatments were used to experimentally induce collagen denaturation, which was quantitated by fluorescence intensity (FI) from the fluorescently-conjugated-CHP (F-CHP) staining (n = 4). FTIR was used to characterize collagen structures. All groups were subject to collagenase digestion to test the bio-stabilization effect of PA on denatured collagen using weight loss analysis and hydroxyproline assay (n = 6). Data were analyzed using two-factor ANOVA and Games-Howell post hoc tests (α = 0.05).

RESULTS

FTIR showed collagen secondary structural changes after denaturation treatments and confirmed the incorporation and cross-linking of PA in control and treated collagen. F-CHP staining indicated high-degree, medium-degree, and low-degree collagen denaturation from H₃PO₄-treatment (FI = 83.22), enzyme-treatment (FI = 36.54), and control (FI = 6.01) respectively. PA modification significantly reduced the weight loss and hydroxyproline release of all groups after digestion (p < 0.0001), with the results correlated with FI values at r = 0.96-0.98.

SIGNIFICANCE

A molecular method CHP is introduced as a sensitive technique to quantitate dentin collagen denaturation for the first time. PA modification is shown to effectively stabilize denatured collagen against collagenase digestion, with the stabilization effect negatively associated with the collagen denaturation degree.

Influence of methylene blue, Riboflavin, and indocyanine green on the bond strength of caries affected dentin when bonded to resin-modified glass ionomer cement

AIM

The present study aimed to assess the influence of methylene blue (MBP), Riboflavin, and indocyanine green (ICG) on the bond strength of caries affected dentin (CAD) when bonded to resin-modified glass ionomer cement (RMGIC).

MATERIALS AND METHODS

Human third molars with caries lesions were isolated and collected scrutinized based on ICDAS criteria. The teeth were cleaned using a periodontal scaler and disinfected. All samples were positioned in polyvinyl up to the cementoenamel junction. The samples were randomly distributed into five groups based on the pretreatment regime. Samples in group 1, were pretreated with MBP; group 2, polyacrylic acid (PAA) group 3, ICG, group 4, Riboflavin photosensitizer, and group 5, 37% phosphoric acid (PA). All samples were bonded with RMGIC. 10 samples were subjected to the universal testing machine for shear bond strength (SBS) testing. Five samples from each group were placed in fuchsine dye for the microleakage assessment. Comparison of means and standard deviations (SD) of SBS and microleakage in investigated groups was performed using analysis of variance (ANOVA) and Tukey's post hoc test at a significance level (p=0.05) RESULTS: : The highest micro shear bond values were observed in group 2 (CAD conditioned with PAA) (14.26±1.67 MPa). Whereas, the lowest bond values were found in group 1 (treated with MBP) (8.82±1.08 MPa). CAD conditioned with different photosensitizers i.e., MBP, ICG, and Riboflavin before bonding to RMGIC displayed comparable bond values (8.82±1.08 MPa), (9.47±0.21 MPa), and (11.23±0.47 MPa) respectively (p>0.05). Samples conditioned with 37% PA showed significantly higher microleakage scores compared to other surface-treated groups (p<0.05).

CONCLUSION

Caries-affected dentin conditioned with polyacrylic acid demonstrated low microleakage and high bond strength.

Examination of caries-affected dentin and composite-resin interface after different caries removal methods: A scanning electron microscope study

To evaluate the caries-affected dentin and composite-resin interface with scanning electron microscopy (SEM) after different caries removal methods in human molars. Twelve with extensive approximal caries lesions that did not reach the pulp and five caries-free molars (control group [CG]) were used. Carious teeth were divided into four experimental groups: Atraumatic Restorative Treatment (ART), Rotary Instrument (RI), Photo-Ablation, and Papain-Based Enzymatic Gel (Brix 3000®, Brix, Brazil). Class II slot cavities were prepared with RI in the CG. Then all caries removed teeth and control groups were restored (All-Bond Universal, BISCO, USA; Clearfil MajestyES-2, Kuraray, Japan). Specimens were prepared for SEM examinations. Hybrid layer (HL) thicknesses were measured using ImageJ programme. Gap measurements were performed with micro-CT. Data were analyzed with ANOVA and posthoc Dunnett's t-tests (p < .05). The highest HL thickness was found in Photo-Ablation Group, and a statistically significant difference was observed among the control and experimental groups (p < .05). The lowest HL thickness was measured in the Enzymatic Gel Group. In terms of internal gap formation, CG showed statistically significant differences compared to the other groups (p < .05). The highest internal gap was observed in RI Group, while the lowest gap was observed in CG. According to SEM, a uniform HL and resin tags were seen in the CG. Smear layer, irregular HL, and gap formation were observed in ART Group. In RI Group, nonuniform HL formation and resin tags were observed. In Photo-Ablation Group, a uniform HL without smear layer and internal gap was observed. In the Enzymatic Gel Group, both opened dentinal tubules, and melting-like formations were observed on the dentin surface. Especially melting-like formations were observed in peritubular dentin. It can be concluded that all caries removal methods except rotary instrumentation were conservative methods, which preserve more healthy dental tissues.

Development and characterization of experimental ZnO cement containing niobophosphate bioactive glass as filling temporary material

Aims

The aim of this study was to develop and characterize a temporary restorative material based on a zinc oxide matrix containing niobophosphate bioactive glass (NbG) for the caries-affected dentin treatment.

Material and methods

NbG was added to a ZnO₂ matrix in different concentrations (wt%). EDS-SEM, ATR-FTIR and XRD analyses were performed to characterize the cement. Calcium release was evaluated in TRIS solution after 1, 7 and 14 days by colorimetric method (A₆₅₀). Compressive strengths and setting times were performed to analyze mechanical properties.

Results

EDS spectra confirmed the presence of Ca, P and Nb in the groups containing NbG. EDS mapping exhibit the ZnO₂ homogeneous distribution, and NbG immersed in this matrix. Peaks suggesting interaction between matrix and NbG were not detected in Ftir spectra. Calcium releasing showed to be time-dependent for experimental groups containing 10, 20, 30 and 40%. The NbG incorporation progressively increased the compressive strength values in the experimental groups. NbG incorporation seemed to influence the ZnO₂ matrix early setting reaction. No statistical difference was observed in the final setting time.

Conclusion

The addition of NbG particles into zinc oxide matrix could work as a mechanical reinforcement. It is suggested that the calcium released by the cement containing at least 10% NbG could induce apatite formation.

Influence of methylthioninium chloride, curcumin and Er, Cr: YSGG on caries affected dentin bonded to bioactive and conventional bulk fill dental restorative material

AIM

The study aimed to determine the influence of Er, Cr: YSGG (ECL), methylene blue photosensitizer (MBP), and curcumin photosensitizer (CP) disinfection on CAD and its bond strength and microleakage to bioactive (BA) and multicore (MC) bulk-fill composite.

MATERIALS AND METHODS

Sixty carious mandibular molars were collected based on the criteria of ICDAS Code 6 (International Caries Detection and Assessment system). Specimens were embedded in polyvinyl pipes up to CEJ and subjected to preparation of standard class II cavity leaving CAD in situ for bonding. All samples were randomly assigned to eight groups based on disinfection regimes and type of bulk-fill material. Samples in group 5 and 6 didn't undergo any disinfection; group 1: ECL + BA, group 2: ECL+ MC; group 3 MBP + BA, group 4: MBP + MC; group 5: Conventional Etch and Rinse + BA (Control), group 6 Conventional Etch and Rinse + MC (Control); group 7: CP +BA and group 8 CP+MC. Specimens were tested for SBS using a universal testing machine and the debonded surfaces were evaluated under a stereomicroscope to determine modes of failure. A dye penetration test was performed for microleakage assessment. For intergroup comparison test analysis of variance (ANOVA) was performed using means and standard deviation from each group. Tukey HSD was used for multiple group comparison tests. The level of significance was established at p < 0.05.

RESULTS

The maximum mean bond strength was shown by group 6 (18.96 ± 0.31 MPa) conventional etch and rinse+ MC (control). Whereas, the minimum SBS was recorded in specimens of group 7 CP +BA (13.04 ± 0.81 MPa). SBS values among group 3 (14.05 ± 0.10 MPa- MBP+BA), group 4 (13.66 ± 0.39- MBP+MC) group 7 (13.04 ± 0.81 MPa- CP +BA and group 8 (14.21 ± 0.59 MPa- CP+MC) were found to be comparable (p>0.05). There was no statistically significant difference among the study groups concerning microleakage (p >0.05).

CONCLUSION

CAD treated with ECL for the adhesive bonding of BA and conventional bulk-fill composite MC has shown potential to be used clinically. Moreover, MBP and CP for conditioning of CAD need further investigation.

Nanoparticle incorporated dentin bonding agent to caries effected dentin treated by photodynamic therapy, laser or chlorhexidine

PURPOSE

This study aims to evaluate the microtensile bond strength (µTBS) and failure modes of graphene nanoplatelets doped with hydroxyapatite (GNP-HA) modified self-etch dentin bonding agent (DBA) to caries effected dentin (CAD) after various conventional and laser disinfection protocols.

MATERIALS AND METHODS

Graphene nanoplatelets and HA nanoparticles were doped and incorporated in DBA. Fifty carious human molar teeth were used for the experiment. CAD specimens were divided into five groups (n=10/group) into CAD undergoing no disinfection treatment (Group-CAD), 2% chlorhexidine disinfection (Group-CHX), 6% NaOCl disinfection (Group-NaOCl), methylene blue assisted PDT (Group-MB-PDT), and Er,Cr:YSGG laser application (Group-Er,Cr:YSGG). Following the respective disinfection techniques, the GNP-HA modified adhesive was applied to all treated CAD surface. Subsequently µTBS and failure modes were analyzed.

RESULTS

Representative scanning electron microscope images (SEM images) of the synthesized GNP-HA indicated flakes of graphene with varying size lengthwise (>500 nm) with 1-2 nm width. The doped HA showed round and spherical morphology conjugated over the surface of the GNP measuring 40 -100 nm in diameter. CAD group that underwent no treatment represented the highest µTBS (29.43 MPa). Within the tested specimens, MB-PDT (22.37 MPa) and Er,Cr:YSGG (21.85 MPa) showed the highest µTBS values than CHX (15.69 MPa) and NaOCl (11.46 MPa). However, there was no significant difference between MB-PDT and Er,Cr:YSGG (p>0.05) and a significant difference existed between CHX and NaOCl (p<0.05). Equal distribution of cohesive and adhesive failures was noted for CAD, CHX and NaOCl treated specimens. A majority of adhesive failures existed in the MB-PDT groups. While admixed and adhesive failures were higher in Er,Cr:YSGG treated samples.

CONCLUSIONS

The outcome of this study suggests that CAD restored by GNP-HA modified self-etch adhesive showed highest bond strength after MB-PDT and Er,Cr:YSGG protocols with low amount of adhesive failure.

Antimicrobial and self-crosslinking potential of experimentally developed dioctadecyldimethyl ammonium bromide and riboflavin dentin adhesive

The aim of the study is to investigate a new formulation, based on dioctadecyldimethyl ammonium-bromide (QA) and riboflavin (RF), combining antimicrobial activities and protease inhibitory properties with collagen crosslinking without interference to bonding capabilities in a rabbit model. Quaternary ammonium riboflavin (QARF) experimental adhesives modified with dioctadecyldimethyl ammonium-bromide and riboflavin were bonded (0.5/1.0/2.0%) to rabbit dentin to investigate for pulpal-histology, interfacial-morphology, transmission electron microscopy, mechanical properties, collagen crosslinking, micro-Raman analysis, antimicrobial, and anti-protease activities. Collagen type-I molecules were generated using molecular-docking. Odontoblasts appeared with normal histology, were seen in controls with no inflammatory cells detected in 0.5% specimens at day 7 and mild inflammatory response at day 30. In QARF 2.0%, inflammatory cells were not detected at day 7 and 30 (p < .05). Dentinal tubules are seen with intact collagen surface in 1% specimens. Resin penetrated inside 1% adhesive specimens with few irregularly funnel-shaped tags. Transmission electron microscopy showed thinner collagen in all specimens except 1% QARF specimens. Biofilms were influenced by QARF adhesives. Elastic moduli were significantly higher in 1.0% and 2.0% QARF adhesive specimens with a significant increase in total crosslinks. Stable amide groups with anti-protease activity was observed in QARF groups. Charged residues were seen in the triple helix hCOL3A1, Gly489-Gly510 after stabilisation with formulation. The 1% QARF modified adhesives improved biochemical and biomechanical properties of rabbit dentin.

Bonding of an ion-releasing restorative material to caries-affected dentin disinfected with photodynamic therapy, Er,Cr:YSGG laser, and chemical disinfectants

AIM

The study aimed to evaluate the microtensile bond strength (μTBS) of giomer, an ion-releasing restorative material, to caries-affected dentin (CAD) when different cavity disinfectant protocols were applied before the restoration.

MATERIAL AND METHODS

Thirty extracted non-carious human third molars were embedded in acrylic resin. The occlusal portions of the samples were excised using an IsoMet saw. After creating artificial caries, samples were divided into six groups (n = 12): sound dentin with no disinfection (Group SD), CAD with no disinfection (Group CAD), CAD disinfected with 2% chlorhexidine gluconate (Group CHX), CAD disinfected with 6% NaOCl (Group NaOCl), CAD disinfected with photodynamic therapy with methylene blue photosensitizer (Group PDT), and CAD disinfected with Er,Cr:YSGG (Group ECYL). Following disinfection protocols, the universal adhesive was applied, and all samples were restored using giomer. Subsequently, μTBS analyses were performed, and data were analyzed statistically.

RESULTS

The highest μTBS values were obtained from the SD and CAD groups, which exhibited no statistical differences (p > 0.05). The PDT and ECYL groups had higher μTBS values compared with the CHX and NaOCl groups (p < 0.05), and all disinfection protocols decreased the bond strength to CAD (p < 0.05).

CONCLUSION

The microtensile bond strength of disinfected CAD was greater with Er,Cr:YSGG laser and photodynamic therapy treatment than with chemical disinfectants. Giomer may enhance the bond strength to CAD, which has a weaker bonding potential than sound dentin due to structural differences. However, disinfection protocols adversely affect adhesion between the restorative material and CAD.

Impact of biomineralization on resin/biomineralized dentin bond longevity in a minimally invasive approach: An "in vitro" 18-month follow-up

OBJECTIVES

To determine the impact of treating caries-affected dentin (CAD) with: 0.2% sodium fluoride (NaF), casein phosphopeptide-amorphous calcium phosphate (CPP-ACP/MI Paste™) or peptide P₁₁-4 (Curodont™ Repair) on the longevity of resin/CAD interface at storage times of 24 -h, 6- and 18-month.

METHODS

255 caries-free third molars were used, and CAD was produced by a biological method. The teeth were randomly distributed into: G1- Sound dentin (SD); G2- CAD; G3- CAD + 0.2% NaF (CAD/NaF); G4- CAD + CPP-ACP (CAD/ACP); G5- CAD + Curodont™ Repair (CAD/P₁₁-4). The Filtek Z350 composite resin block was bonded to dentin using Adper™ Single 2 (4 mm/height). Resin/dentin blocks were stored in a solution of Simulated Body Fluid at 37 °C, pressures were modified to simulate natural pulpal pressures. Specimens were investigated by microtensile bond strength (μTBS) (n = 8), Scanning Electron Microscopy (to assess the failure mode) (n = 8), nanoinfiltration (to assess the interface sealing) (n = 3), in situ zymography (to assess the gelatinolytic activity) (n = 3) and micro-computed microtomography (μ-CT) (to assess the mineralization) (n = 3). Data from μTBS, μ-CT and, nanoinfiltration and hybrid layer formation/degradation were submitted to two-way ANOVA and Tukey tests, and failure patterns and in situ zymography to Kruskal-Wallis and Dunn tests (α = 5%).

RESULTS

The highest mineral density change by μ-CT, smallest silver nitrate infiltration and proteolytic activity in the adhesive layer were obtained significantly for the groups SD, CAD/ACP and CAD/P₁₁-4, with most mixed fractures at 18-month (p < 0.001). CAD/NaF showed significantly similar values to CAD, CAD and CAD/NaF which presented a high percentage of adhesive fracture (p < 0.001) at all time periods.

SIGNIFICANCE

Treating caries-affected dentin with remineralizing agents CPP-ACP and Curodont™ Repair, has the potential to be a clinically relevant treatment protocol to increase the longevity of adhesive restorations.

Substantial regional differences in the biomechanical behavior of molar treated with selective caries tissue removal technique: a finite element study

OBJECTIVES

Selective caries removal (SCR) is recommended over non-selective removal for managing deep carious lesions to avoid pulp exposure and maintain pulp vitality. During SCR, residual carious dentin is left behind and sealed beneath the restoration. The biomechanical effects of such residual lesions on the restored tooth remain unclear and were assessed using finite element modeling (FEM).

METHODS

Based on μ-CT images of a healthy permanent human third molar, we developed five finite element models. Generic class I and II cavity restorations were modeled where residual lesions of variable sizes were either left or fully removed on occlusal and proximal surfaces. The cavities were restored with adhesive composite. All 3D-FE models were compared with a model of a healthy, non-treated molar. A vertical load of 100 N was applied onto the occlusal surface.

RESULTS

Regardless of the lesion size, in molars with occlusal lesions higher mean stresses were predicted along the filling-lesion interface than in all other models. The smallest occlusal lesion (Ø₁ = 1 mm) resulted in the highest maximum stresses at the filling-lesion interface with large stress concentrations at the filling walls indicating failure risk. In conclusion, lesion site and extent are influencing parameters affecting the filling-lesion interactions and thus the biomechanical behavior of the tooth after SCR.

SIGNIFICANCE

Retaining carious lesions around the pulpal floor affects the deformation and stress states in tooth-filling complexes. The higher stresses observed in molars with occlusal lesions may affect restoration stability and longevity. Suprisingly, more extended occlusal lesions may provide a more favorable tooth performance than less extended ones. In contrast, in molars with proximal lesions the residual lesion had only limited effect on the tooth's biomechanical condition.

The ability of a nanobioglass-doped self-etching adhesive to re-mineralize and bond to artificially demineralized dentin

OBJECTIVE

To a self-etch adhesive doped with nano-bioglass and evaluate its ability to bond and re-mineralize artificially demineralized dentin.

METHODS

Experimental Si, Ca, Na and PO₄ based nanobioglass particles were synthesized, doped into experimental self-etch adhesives, and divided into 3 groups: Clearfi SE2 (CSE2), experimental (EXC), and experimental doped with 10% of nanobioglass (ExNB). The adhesives were applied onto the caries-affected dentin (chemically simulated), and evaluated after 24 h and 28 days of immersion in simulated body fluid. The remineralization process was assessed using optical coherence tomography, nanoindentation, in situ zymography, transmission electron microscopy, confocal laser scanning microscopy, μ-tensile bond strength, and pH buffer.

RESULTS

The addition of nanobioglass particles into the experimental self-etch adhesives altered the μTBS in the short-term jeopardizing dentin bonding properties, when compared to the non-doped self-etch adhesive. The remineralization recovered the nanohardness, and volume lost by caries lesion (p = 0.02). Moreover, reduced the enzymatic activity (p = 1.24^E-4) and formed new crystals within of the hybrid layer.

CONCLUSION

The use of nanobioglass was efficient to recover the properties of a caries affected dentin. Furthermore, the adhesive properties were not hampered and the probabilistic reliability increased.

Current perspectives on dental adhesion: (2) Concepts for operatively managing carious lesions extending into dentine using bioactive and adhesive direct restorative materials

This article reviews the current concepts for operatively managing carious lesions extending into dentine with minimal removal of tooth structure and restoring with dentine adhesives and direct composite resin. It looks sequentially at the operative steps involved including remineralisation with bioactive cements, bonding to caries-affected dentine including smear-layer modification using HOCl, creation of an acid-base resistance zone,steps to optimise the performance of all-in-one adhesives, and incremental placement of direct composite resin to improve bond strengths to cavity floor dentine. It explores how understanding the phenomenon of colour-shifting at the composite resin-enamel/dentine restoration borders can help in creating near "invisible" restoration margins through a "chameleon" effect. With the increased risks of transmission of Covid-19 when aerosol generating procedures are carried out in Dentistry, following a minimally invasive approach to managing dental caries should be given serious consideration.

Influence of selective caries excavation on marginal penetration of class II composite restorations in vitro

Selective caries excavation may support pulp preservation. This in vitro study investigated the influence of selective removal of demineralized dentin on marginal integrity of composite restorations as determined by dye penetration. Dentinal caries-like lesions were produced in the approximal surfaces of 40 extracted human molars (ethylenediaminetetraacetate, 0.5 M, 96 h). The following test procedures were established: complete excavation, selective excavation, and caries-free control. Two class II cavities with enamel at the cervical margins were prepared per tooth and demineralization volume was determined by micro-computed tomography for the purpose of a stratified distribution to receive complete excavation or selective excavation. After complete or selective excavation (30 cavities each), adhesive composite restorations were placed. Cavities without demineralized dentin (20 cavities) served as control. The marginal integrity of restorations was evaluated by dye penetration with and without thermocycling or mechanical loading. Results were analyzed by non-parametrical statistical tests (Mann-Whitney U Test) with an α = 0.05 level of significance. Dye penetration did not differ significantly among completely excavated, selectively excavated, or undemineralized teeth, but was increased by thermocycling and mechanical loading in all experimental groups. Selective caries removal did not increase marginal penetration in class II restorations. The presence of remaining demineralized dentin surrounded by sound dentin did not impair marginal integrity of restorations with margins placed in sound enamel.

Efficacy of chlorhexidine, Er Cr YSGG laser and photodynamic therapy on the adhesive bond integrity of caries affected dentin. An in-vitro study

AIM

To evaluate the adhesive bond integrity (shear bond strength-SBS) of composite resin bonded to carious dentin using chlorhexidine gluconate (CHX), Er,Cr:YSGG laser (ECYL) and photodynamic therapy (PDT).

MATERIAL AND METHODS

Thirty carious and ten non-carious mandibular teeth were collected through non-traumatic extraction. All samples were embedded in polyvinyl cross-sections to the cemento-enamel junction. The preparation of caries-affected dentin was performed by grinding the specimens using silicon carbide discs. All specimens were randomly allocated in to four groups (n = 10). Group 1, non-affected dentin with no disinfection; Group 2, caries affected dentin treated with 2% CHX; Group 3, affected dentin disinfected with PDT [100 mg/L methylene blue solution (MBS) and Diode laser]; Group 4, affected dentin treated with ECYL. Self-etch adhesive was smeared on all specimens for 10 s and photopolymerized for 10 s. All specimens were placed in an incubator with humid environment for 24 h at 37 °C followed by positioning in universal testing machine for SBS testing. Failure mode examination of debonded samples was performed by a stereomicroscope. Analysis of variance (ANOVA) was used for inter group comparison through mean and standard deviation of each group. For multiple group comparison Tukey HSD was employed. Level of significance was established at p < 0.05.

RESULTS

The highest SBS value was observed in group 1 (24.98 ± 1.59 MPa). Whereas, the lowest bond strength was displayed by group 3 (14.22 ± 1.40 MPa) specimens. Lased dentin in group 4 (15.89 ± 3.22 MPa) exhibited SBS values comparable to group 3 (14.22 ± 1.40 MPa). Group 2 (CHX-18.25 ± 1.29 MPa) exhibited statistically significant difference compared to all experimental groups (p < 0.05).

CONCLUSIONS

Adhesive bond strength of disinfected carious dentin was higher with CHX treatment as compared to Photodynamic therapy and Er,Cr: YSGG laser treatment. Carious dentin showed lower bond strength to composite resin as compared to non-carious dentin.

Caries removal with Er:YAG laser followed by dentin biomodification with carbodiimide and chitosan: Wettability and surface morphology analysis

This study aimed to investigate dentin wettability and surface morphology after selective removal of carious lesion by erbium-doped yttrium aluminum garnet (Er:YAG) laser, followed by dentin biomodification with carbodiimide (EDC) and chitosan (CHI). Seventy-eight bovine dentin specimens were submitted to caries induction. Specimens were distributed according to methods of carious removal (n = 39): bur at low-speed (40,000 rpm) or Er:YAG laser (noncontact mode, 250 mJ/pulse and 4Hz). All specimens were etched with 35% phosphoric acid, and subdivided according to dentin biomodification (n = 13): Control (no biomodification), EDC or CHI. The contact angle (n = 10) between adhesive system (3M ESPE) and dentin surface was measured by a goniometer. Eighteen specimens (n = 3) were analyzed by scanning electron microscopy. Data were analyzed by two-way ANOVA and Tukey's test (α = .05). The method used to remove carious lesion did not influence the wettability of dentinal surface (p = .748). The angles produced on the remaining dentin after biomodification were influenced (p = .007). CHI promoted higher contact angles (p = .007) and EDC did not differ from the control group (p = .586). In the bur-treated group, most tubules were open, regardless of which biomodifier was used. Laser modified the organic matrix layer. CHI promoted partially closed tubules in some areas while EDC exposed dentinal tubules. Regardless of which method was used for selective removal of carious lesion, biomodification with EDC did not affect the dentin wettability, whereas CHI changed the wettability of remaining dentin. Both biomodifiers promoted a slight change on dentin morphology.

Comparison of the micro-tensile bond strengths of four different universal adhesives to caries-affected dentin after ER:YAG laser irradiation

The micro-tensile bond strengths (micro-TBSs) of four universal adhesive systems, applied in two different bonding techniques, to carries-affected dentin after Er:YAG laser irradiation were investigated. Twenty-four extracted human molars were divided into four groups, according to the adhesive systems used. Each group was subdivided into two subgroups, depending on the bonding method used: the etch-and-rinse procedure or self-etch procedure. The carious lesions were irradiated using an Er:YAG laser. Resin composites were used to restore the adhesive-treated dentin surfaces. After 2,500 thermal cycles, the vertical composite resin-dentin sticks obtained were subjected to micro-TBS tests. One tooth in each group was examined using scanning electron microscopy (SEM). There were statistically significant differences (p<0.001) in micro-TBS values between universal adhesives. The results of this study suggested that universal adhesives applied both with self and total etch technique can be used for adhesive restorations to caries-affected dentin after Er:YAG laser irradiation. If lasers are preferred as a caries removal method, choosing a dentin bonding agent containing MDP may be recommended in clinical practice due to the property of increasing the bonding strength.

Monitoring demineralization and remineralization of human dentin by characterization of its structure with resonance-enhanced AFM-IR chemical mapping, nanoindentation, and SEM

OBJECTIVE

This research aimed at monitoring demineralization and remineralization of dentin and its collagen matrix at the nanoscale by amorphous, microcrystalline, and in situ formed hydroxyapatite.

METHODS

The concurrent use of the resonance-enhanced atomic force microscopy coupled with infrared probe (AFM-IR) chemical mapping, nano-indentation, and scanning electron microscopy (SEM) provides a detailed insight into the structure of human dentin, as well as to the processes of its partial demineralization and remineralization.

RESULTS

The resonance-enhanced AFM-IR chemical mapping of dentin has shown to be a useful method to follow distribution of its collagen and hydroxyapatite components at the micro- and nanoscale levels, especially in conjunction with SEM imaging and nanoindentation. Dentin with a higher extent of natural dentin tubule occlusion tends to be harder and less elastic. The relative affinity of the collagen and hydroxyapatite components of dentin toward hydroxyapatite depends on its type (amorphous, microcrystalline, or formed in-situ). The gel mineralization technique allows for an even and controlled growth of hydroxyapatite guided by the completely demineralized collagen matrix of dentin.

SIGNIFICANCE

The observed trends of the affinity of collagen toward different forms of hydroxyapatite helps develop new remineralizing formulations. The employed methods of characterization may provide an insight to the natural processes of bone mineralization guided by its both hydroxyapatite and protein constituents.

Elevation of an Amalgam-stained Margin With Resin-modified Glass Ionomer to Support an Indirect Ceramic Restoration: A Six-year Case Report

This case report presents treatment of a mandibular second molar with an extensive proximal margin, which was finished on amalgam-stained dentin. A resin-modified glass ionomer for margin elevation and a lithium disilicate onlay were used to restore the tooth to proper form and function. The patient has been followed for six years and has had no complications during this period.

An in vitro study on dentin demineralization and remineralization: Collagen rearrangements and influence on the enucleated phase

Dentin remineralization is of clinical relevance in the therapy of caries and dentin hypersensitivity. This study is aimed at gaining more insights on a molecular scale, through IR spectroscopy, into dentin demineralization and remineralization. The dentin demineralization by ethylenediaminetetraacetic acid, EDTA (17%, 2 h) significantly altered the secondary structure distribution of collagen, upon loss of interaction with calcium ions. To investigate dentin remineralization, previously demineralized human dentin slices were soaked in Dulbecco's Phosphate Buffered Saline (DPBS) or Hank's Balanced Salt Solution HBSS, in close contact with three commercial cements used as sustained releasing sources of Ca²⁺ and OH^- ions (i.e. calcium hydroxide- and calcium silicate-based cements). IR spectroscopy showed the occurrence of remineralization under these conditions. Collagen did not lose its ability to chelate Ca²⁺, and these interactions allowed collagen to rearrange into a conformation similar to that of sound dentin. This process appeared slower in HBSS than DPBS, as also shown by the lower degree of maturation of the inorganic phase enucleated in the former medium (amorphous calcium phosphate versus B-type carbonated apatite). Collagen appeared to act as a spatial constraint to crystal deposition, affecting crystallinity and carbonate content of the enucleated phase. Remineralization was found to strongly depend on the calcium releasing ability of the cements. The fast formation of a rough apatite biocoating may represent a favorable clinical condition in the context of mineralized tissue regeneration.

Effect of epigallocatechin-3- gallate solutions on bond durability at the adhesive interface in caries-affected dentin

Hydrolytic and enzymatic degradation by matrix metalloproteinases (MMPs) reduces the durability of composite resin restorations on caries-affected dentin (CAD). The use of MMP inhibitors such as epigallocatechin-3-gallate (EGCG) could increase the longevity of the bond to dentin. This study aimed to evaluate the use of EGCG at different aqueous concentrations on the resin-dentin microtensile bond strength (μTBS), fracture pattern and nanoleakage (NL) in immediate (IM) time interval and after 12-months of water storage (1Y) when using a two-step etch-and-rinse adhesive system on CAD. Dentin surfaces of 40 human molars were submitted to a microbiological caries induction protocol and randomized into 5 groups (n = 8) (0.02% EGCG; 0.2% EGCG; 0.5% EGCG; 2% Chlorhexidine [CHX] and no treatment as Control Group - [NT]). After acid etching, the solutions were applied for 60 s followed by application of dental adhesive (Adper Single Bond 2, 3 M ESPE) to CAD surfaces. Subsequently, a resin composite (4 mm) block was built on the dentin. After 24 h, the teeth were sectioned into beam-shaped specimens (cross-sectional area of 1 mm² and 8-mm high). Half of the specimens were tested in IM and the other half after 1Y. Two samples per tooth were submitted to SEM for NL evaluation. Data were statistically analyzed by two-way ANOVA and Tukey tests (α = 0.05). The results showed that use of EGCG and CHX did not affect μTBS in IM (p > 0.05). After 1Y, there was a reduction in μTBS for all experimental groups (p < 0.05). Adhesive fractures predominated in IM in all groups, except for 0.05% EGCG and NT. After 1Y, there was an increase in these adhesive fractures in all groups. For NL, all agents applied reduced NL in comparison with CT (p < 0.001). CHX showed lower NL (p < 0.001), followed by 0.02% and 0.5% EGCG. NT showed highest NL for both time intervals (p < 0.001). Thus, although the use of EGCG at different concentrations and CHX reduced the NL, they were unable to reduce degradation of μTBS to CAD over time.

Effect of casein phosphopeptide-amorphous calcium phosphate on fluoride release and micro-shear bond strength of resin-modified glass ionomer cement in caries-affected dentin

Objectives

This study was conducted to evaluate fluoride release and the micro-shear bond strength of resin-modified glass ionomer cement (RMGIC) in casein phosphopeptide-amorphous calcium phosphate (CPP-ACP)-remineralized caries-affected dentin (CAD).

Materials and Methods

Exposed dentin surfaces of 30 human third molar teeth were divided into 2 equal groups for evaluating fluoride release and the micro-shear bond strength of RMGIC to CAD. Each group was subdivided into 3 equal subgroups: 1) control (sound dentin); 2) artificially demineralized dentin (CAD); 3) CPP-ACP remineralized dentin (remineralized CAD). To measure fluoride release, 15 disc-shaped specimens of RMGIC (4 mm in diameter and 2 mm in thickness) were bonded on one flat surface of the dentin discs of each group. Fluoride release was tested using ion chromatography at different intervals; 24 hours, 3, 5, 7 days. RMGIC micro-cylinders were built on the flat dentin surface of the 15 discs, which were prepared according to the assigned group. Micro-shear bond strength was measured after 24 hours water storage. Data were analyzed using 1- and 2-way analysis of variance and the post hoc least significant difference test (α = 0.05).

Results

Fluoride detected in solutions (at all intervals) and the micro-shear bond strength of RMGIC bonded to CPP-ACP-remineralized dentin were significantly higher than those bonded to artificial CAD (p < 0.05).

Conclusions

Demineralized CAD consumes more fluoride released from RMGIC into the solution for remineralization than CPP-ACP mineralized dentin does. CPP-ACP increases the micro-shear bond strength of RMGIC to CAD.

Clinical, double blind, randomized controlled trial of experimental adhesive protocols in caries-affected dentin

OBJECTIVE

To evaluate the clinical performance of posterior resin composite restorations regarding experimental and regular adhesive protocols in caries affected-dentin (CAD).

MATERIAL AND METHODS

A total of 92 class I and class II cavities with carious lesions were selected and randomly assigned to the following groups: (1) bioactive glass-ceramic powder/two-step etch and rinse system, (2) control/two-step etch and rinse system, (3) bioactive glass-ceramic powder/two-step self-etching system, and (4) control/two-step self-etching system. Two operators carried out the adhesive protocols and restored the cavities with a nano-hybrid resin composite. Participants were followed up at 1 week and 6, 12, and 18 months for clinical evaluation performed by two blinded examiners and calibrated according to FDI criteria. Data were analyzed using Kruskal-Wallis and Dunn tests with a confidence of 95%.

RESULTS

The clinical performance of resin composite restoration was not affected by the experimental use of an adhesive protocol including a bioactive glass-ceramic powder for 18 months post-procedure. However, there was a significant difference between group 2 and group 4 (p < 0.05) for marginal adaptation (18 months). Group 2 was significantly different from group 3 (p < 0.05) for fracture of material/retention (18 months) and marginal adaptation (1 week); group 2 showed a better performance.

CONCLUSION

Adhesive protocols can alter the clinical performance of posterior restorations in terms of marginal adaptation and the fracture of material/retention in CAD.

CLINICAL SIGNIFICANCE

Adhesive protocols may influence the success of resin composite restorations in CAD; this is important because failure can lead to caries, re-incidence, and/or clinical re-work.

Biomimetic Mineralizing Agents Recover the Micro Tensile Bond Strength of Demineralized Dentin

Biomimetic remineralization is an approach that mimics natural biomineralization, and improves adhesive procedures. The aim of this paper was to investigate the influence of Dentin Caries-like Lesions (DCLL)-Producing Model on microtensile bond strength (μTBS) of etch and rinse adhesive systems and investigate the effect of remineralizing agents such as Sodium Fluoride (NaF), MI Paste™ (MP) and Curodont™ Repair (CR) on caries-affected dentin (n = 6). Nine groups were established: (1) Sound dentin; (2) Demineralized dentin/Chemical DCLL: (3) Demineralized dentin/Biological DCLL; (4) Chemical/DCLL + NaF; (5) Chemical/DCLL + MP; (6) Chemical/DCLL + CR; (7) Biological/DCLL + NaF; (8) Biological/DCLL + MP; (9) Biological/DCLL + CR. Then all dentin blocks were subjected to a bonding procedure with Adper™ Single Bond 2 adhesive system/Filtek Z350XT 4 mm high block, following this they were immersed in deionized water/24 h and then sectioned with ≅1 mm² beams. The μTBS test was conducted at 1 mm/min/500 N loading. Failure sites were evaluated by SEM (scanning electron microscopy (150×). μTBS data were submitted to factorial ANOVA and Tukey’s test (p < 0.05). The highest values were found when demineralized dentin was treated with MP and CR, regardless caries lesion depth (p < 0.05). There was a predominance of adhesive/mixed in the present study. It was concluded that the use of the artificial dentin caries production models produces differences in the μTBS. Additionally MP and CR remineralizing agents could enhance adhesive procedures even at different models of caries lesion.