Heterogeneous activation of persulfate by Co3O4-CeO2 catalyst for diclofenac removal

Cerium oxide /Co-Co Prussian blue analogue composite catalyst for enhanced peroxymonosulfate activation for effective removal of tetracycline hydrochloride from water

In this paper, a novel CeO2/Co3[Co(CN)6]2 (CeO2/PBACo-Co) composite was prepared with co-precipitation and utilized to activate peroxymonosulfate (PMS) to eliminate tetracycline hydrochloride (TCH). Catalyst screening showed that the composite with a CeO2:PBACo-Co mass ratio of 1:5 (namely, 0.2-CeO2/PBACo-Co) had the best performance. The degradation efficiency of TCH in 0.2-CeO2/PBACo-Co/Oxone system was investigated. The experimental results illustrated that 98% of 50 mg/L TCH and 48.5% of TOC were degraded by 50 mg/L 0.2-CeO2/PBACo-Co and 400 mg/L Oxone within 120 min at 25 °C and initial pH 5.3. Recycling studies showed that the elimination rate of TCH can still achieve 85.8% after five cycles, suggesting that 0.2-CeO2/PBACo-Co composite processes good reusability. Trapping experiments and EPR tests revealed that the reaction system produced multiple active species (1O2, O2•-, SO4•-, and •OH). We proposed the catalytic mechanism of 0.2-CeO2/PBACo-Co for PMS activation, which mainly involves the promoted Co3+/Co2+ cycle by Ce3+ donated electrons. These results indicate that CeO2/PBACo-Co composite is an effective catalyst for wastewater remediation.

Insights into the mechanism of multiple Cu-doped CoFe2O4 nanocatalyst activated peroxymonosulfate for efficient degradation of Rhodamine B

The multiple metal catalyst as a promising nanomaterial has shown excellent activity in the peroxymonosulfate (PMS) activation for pollutant degradation. However, the role of special sites and in-depth understanding of the PMS activation mechanism are not fully studied. In this study, a Cu-doped CoFe2O4 nanocatalyst (0.5CCF) was synthesized by a sol-gel and calcination method, and used for PMS activation to remove Rhodamine B (RhB). The results showed that the Cu doping obviously enhanced the catalytic performance of CoFe2O4, with 99.70% of RhB removed by 0.5CCF while 74.91% in the CoFe2O4 within 15 min. Based on the X-ray photoelectron spectroscopy and electrochemical analysis, this could be ascribed to the more low valence of Co and Fe species generated on the 0.5CCF and faster electron transfers occurred in the 0.5CCF due to the Cu doping. In addition, Cu doping could provide more reaction sites for the 0.5CCF to activate PMS for RhB removal. The metal species and the surface hydroxyl were the reaction sites of PMS activation, and the surface hydroxyl played an important role in surface-bound reactive species generation. During the PMS activation, the Cu not only activated PMS to produce reactive oxygen species (ROS), but also regenerated Co2+ and Fe2+ to accelerate the PMS activation. The non-radical of 1O2 was the main ROS with a 99.35% of contribution rate, and the SO5•- self-reaction was its major source. This study provides a new insight to enhance the PMS activation performance of multiple metal catalysts by Cu doping in wastewater treatment.

Boosting N2O Catalytic Decomposition by the Synergistic Effect of Multiple Elements in Cobalt-Based High-Entropy Oxides

Nitrous oxide (N2O) has a detrimental impact on the greenhouse effect, and its efficient catalytic decomposition at low temperatures remains challenging. Herein, the cobalt-based high-entropy oxide with a spinel-type structure (Co-HEO) is successfully fabricated via a facile coprecipitation method for N2O catalytic decomposition. The obtained Co-HEO catalyst displays more remarkable catalytic performance and higher thermal stability compared with single and binary Co-based oxides, as the temperature of 90% N2O decomposition (T90) is 356 °C. A series of characterization results reveal that the synergistic effect of multiple elements enhances the reducibility and augments oxygen vacancy in the high-entropy system, thus boosting the activity of the Co-HEO catalyst. Moreover, density functional theory (DFT) calculations and the temperature-programmed surface reaction (TPSR) with isotope labeling demonstrate that N2O decomposition on the Co-HEO catalyst follows the Langmuir-Hinshelwood (L-H) mechanism with the promotion of abundant oxygen vacancies. This work provides a fundamental understanding of the synergistic catalytic effect in N2O decomposition and paves the way for the novel environmental catalytic applications of HEO.

Facile fabrication of CoAl-LDH nanosheets for efficient rhodamine B degradation via peroxymonosulfate activation

Layered double hydroxides (LDHs) have been extensively investigated as promising peroxymonosulfate (PMS) activators for the degradation of organic pollutants. However, bulk LDHs synthesized using conventional methods possess a closely stacked layered structure, which seriously blocks active sites and yields low intrinsic activity. In this study, we exfoliated bulk CoAl-LDHs to fabricate CoAl-LDH nanosheets by alkali-etching and Ostwald ripening via a simple hydrothermal process in a KOH solution. The exfoliated LDHs possessed the typical nanosheet structure with more exposed active sites for PMS activation, and hence, boosted the degradation of the pollutants. CoAl-1 exhibited an outstanding catalytic performance as the PMS activator for rhodamine B (RhB) degradation with the apparent rate constant of 0.1687 min-1, which was about 3.63 and 5.02 times higher than that of commercial nano-Co3O4 and bulk CoAl-LDH, respectively. The maximum RhB degradation of 93.1% was achieved at the optimal reaction conditions: catalyst dose 0.1 g L-1, PMS concentration 0.3 mM, pH 7, and temperature 298 K. Further analysis of RhB degradation mechanism illustrated that singlet oxygen (1O2) dominated RhB degradation in the CoAl-1/PMS system, while ˙OH, ˙O2-, and ˙SO4- may mainly serve as the intermediates for the generation of 1O2 and were indirectly involved in the degradation. This study provides a promising strategy for developing two-dimensional LDH nanosheets for wastewater remediation.

Ultrasmall nitrogen-doped Cu0·92Co2·08O4 nanocrystal-decorated cerium dioxide nanoparticles for fast and complete degradation of ranitidine via permonosulfate activation

A simple and efficient coagulation method was used for the rapid preparation of nitrogen-doped copper-cobalt oxide (N-Cu_0.92Co_2·08O₄) supported on cerium dioxide (CeO₂), that is, N-Cu_0.92Co_2·08O₄@CeO₂. A low concentration of N-Cu_0.92Co_2·08O₄@CeO₂ (0.15 g L^-1) was shown to rapidly activate permonosulfate (PMS) (0.15 g L^-1) to achieve 100% degradation of ranitidine within 10 min. A 100% degradation of ranitidine enabled by the catalyst was achieved over a wide range of pH (5.5-9.0), which could be completed within 8 min in the presence of anionic H₂PO₄^-. Moreover, the N-Cu_0.92Co_2·08O₄@CeO₂ catalyst enabled more than 90% degradation of various typical antibiotics within 30 min, including tetracycline, sulfaixoxazole, and chloramphenicol, with degradation rates of 100%, 93.51%, and 90.01%, respectively. Even after four catalytic cycles, N-Cu_0.92Co_2·08O₄@CeO₂ could be regenerated to achieve 100% degradation of ranitidine. Electrochemical analysis demonstrated that the combination of N-Cu_0.92Co_2·08O₄@CeO₂ and PMS immediately produced a strong current density, thereby rapidly producing reactive oxygen species (ROS) with high performance for the degradation of the target pollutant. Combined ion quenching and electron paramagnetic resonance analyses indicated that the main ROS was the non-free radical ¹O₂. Finally, a plausible ranitidine degradation pathway was deduced based on liquid chromatography-mass spectrometry (LC-MS) analysis, wherein the toxic substance N-nitrosodimethylamine was not produced during the degradation process. In short, this study provides a new perspective for preparing ternary metal catalysts for advanced oxidation processes with practical application significance.

Persulfate promoted visible photocatalytic elimination of bisphenol A by g-C3N4-CeO2 S-scheme heterojunction: The dominant role of photo-induced holes

In the last few years, coupling heterogeneous photocatalysis with persulfate (PDS) activation process is an efficient approach to generate abundant reactive oxidative species towards organic contaminant removal in water, however, the key role of PDS in photocatalytic process remains ambiguous. Herein, a novel g-C₃N₄-CeO₂ (CN-CeO₂) step-scheme (S-scheme) composite was constructed to photo-degrade bisphenol A (BPA) with the presence of PDS under visible irradiation. At 2.0 mM PDS, 0.7 g/L CN-CeO₂ and natural pH 6.2, 94.2% of BPA could be eliminated in 60 min under visible light (Vis) illumination. Aside from the previous view of free radical generation, it tends to assume that most of PDS molecules acted as electron sacrificial agents for capturing photo-induced e^- to form sulfate ions, greatly improving the charge carrier separation and thus enhancing the oxidation capacity of nonradical hole (h⁺) for the removal of BPA. Good correlations are further found between the rate constant and descriptor variables (i.e., Hammett constant σ^-/σ⁺ and half-wave potential E_1/2), exhibiting selective oxidation for organic pollutants in the Vis/CN-CeO₂/PDS system. The study brings more insights into mechanistic understanding of persulfate-enhanced photocatalytic process for addressing water decontamination.

CuO nanosheets incorporated scrap steel slag coupled with persulfate catalysts for high-efficient degradation of sulfonamide from water

A highly efficient and magnetically recoverable persulfate (PS) catalyst was prepared for the removal of sulfonamide (SMD) from wastewater, which is difficult to be degraded by the conventional biological treatment. In this study, the scrap steel slag (SSS) was used as supporting carrier and the CuO nanosheet was incorporated on the surface of SSS. The optimal conditions were determined as follows: the dosage of CuO/SSS was 1 g L^-1, the PS concentration was 4 mM and the optimal initial pH was 6.85. Under the optimal conditions, the maximum SMD removal efficiency of 80.29% was achieved within 30 min by using CuO/SSS + PS. In addition, the CuO/SSS + PS system had a wide pH range (5-9) and more than 60% removal efficiency of SMD could be obtained with the pH between 3 and 11. The mechanism based on the phase transformation of Cu(I/II), Cu(II/III) and Fe(II/III) was elucidated by using different analytical techniques, such as SEM, XRD, XPS, BET, FTIR, VSM characterization and free radical analysis. This study provided a new pathway for the SSS resource utilization and the effective degradation of SMD from the refractory wastewater by using CuO/SSS catalyst coupled with PS system.

Tuning the pore structure of templated mesoporous poly(melamine-co-formaldehyde) particles toward diclofenac removal

The increasing demand and implementation of pharmaceutics poses severe risk to different aquatic species as detectable contaminant in almost every surface water worldwide. Diclofenac (DCF) as one of the most common used analgesics was investigated as contaminant to be removed by adsorption onto nanoporous poly(melamine-co-formaldehyde) (PMF) particles featuring a very high amount of nitrogen functionalities. To achieve a high specific surface area (up to 416 m²/g) and a tunable pore system by hard templating, four different SiO₂ nanoparticles were used as template. Differences in the pore formation and achieved pore structure were elucidated. For the first time, the adsorption of DCF onto PMF was tested. In batch adsorption experiments, impactful adsorption capacities as high as 76 μmol/g were achieved and complete removal at initial concentrations of 2 mg/L DCF. Differences in the connectivity and the micropore structure were decisive for uptake in low concentrations and the achieved adsorption capacity, respectively. As the presented PMF particles can be easily synthesized with the monomers formaldehyde and melamine combined with colloidal silica as sacrificial template and water as green solvent, this material presents a viable adsorbent for the removal of DCF at a larger scale. Our study further indicates a high potential for the removal of other pharmaceuticals.

Removal of Pharmaceuticals and Personal Care Products (PPCPs) by Free Radicals in Advanced Oxidation Processes

As emerging pollutants, pharmaceutical and personal care products (PPCPs) have received extensive attention due to their high detection frequency (with concentrations ranging from ng/L to μg/L) and potential risk to aqueous environments and human health. Advanced oxidation processes (AOPs) are effective techniques for the removal of PPCPs from water environments. In AOPs, different types of free radicals (HO·, SO₄·^-, O₂·^-, etc.) are generated to decompose PPCPs into non-toxic and small-molecule compounds, finally leading to the decomposition of PPCPs. This review systematically summarizes the features of various AOPs and the removal of PPCPs by different free radicals. The operation conditions and comprehensive performance of different types of free radicals are summarized, and the reaction mechanisms are further revealed. This review will provide a quick understanding of AOPs for later researchers.

Waste coal cinder catalyst enhanced electrocatalytic oxidation and persulfate advanced oxidation for the degradation of sulfadiazine

Waste coal cinder, a kind of waste cinder discharged from coal combustion of thermal power plants, industrial and civil boilers, and other equipment, was rich in metal oxides with catalytic activity. In this work, waste coal cinder was used to enhance electrochemical coupling peroxymonosulfate (PMS) advanced oxidation degradation of sulfadiazine (SD). The surface morphology, elemental composition, and electrocatalytic activity of waste coal cinder were characterized by various characterization instruments. The results show that compared with simple electrocatalytic oxidation, electrocatalytic oxidation + waste coal cinder and electrocatalytic coupled persulfate oxidation, electrocatalytic oxidation + PMS advanced oxidation + waste coal cinder has the largest removal efficiency (99.95%) and mineralization rates (90.16%) of SD in 90 min, indicating that the introduction of waste coal cinder greatly increases the degradation efficiency. •OH and SO₄^-• were detected during the process of degradation. The optimal degradation process parameters were explored through different voltage, pH, plate spacing, aeration flow rate, potassium peroxymonosulfate sulfate complex salt dose, and Na₂SO₄ dosage. Cycling experiments show waste coal cinder has good structural stability. Through the analysis of triple quadrupole liquid chromatography-mass spectrometry (LC-MS), we put forward three possible ways of SD degradation. This research will provide a novel vision for water treatment.

Efficient activation of peroxymonosulfate mediated by Co(II)-CeO2 as a novel heterogeneous catalyst for the degradation of refractory organic contaminants: Degradation pathway, mechanism and toxicity assessment

A series of Co(II)-CeO₂ mixed metal oxides were synthesized by a facile hydrothermal-calcination procedure for activating peroxymonosulfate (PMS) and degrading toxic and difficult biodegradable organics. Co(II)-CeO₂ showed excellent degradation performance toward rhodamine B (RhB), toluidine blue, methylene blue and diclofenac. RhB is a refractory organic contaminant, and ecotoxicological evaluation unraveled its harmfulness to the biosphere. RhB was selected as the model pollutant to investigate catalytic mechanisms. Parameters affecting degradation performance were profoundly investigated, including Co:Ce feed ratio, initial pH, PMS dosage, catalyst dosage, RhB concentration, coexisting ions and reaction temperature. Reaction mechanisms were proposed based on density functional theory calculations and identifications of reactive oxygen species. Improvements have been achieved in seven aspects compared to previous studies, including 100% degradation ratio in both real water samples and each reuse of the catalyst, ultrafast degradation rate, cost-effectiveness of the catalyst, toxicity-attenuation provided by the developed degradation method, high degree of mineralization for the model pollutant, negligible leaching of active sites, and the enhancement of catalytic performance by utilizing trace leached cobalt, endowing the technique with broad applicability and prospect.

New insight into degradation of chloramphenicol using a nanoporous Pd/Co3O4cathode: characterization and pathways analysis

The growing chloramphenicol (CAP) in wastewater brought a serious threat to the activity of activated sludge and the spread of antibiotics resistance bacteria. In this study, a highly ordered nanoporous Co₃O₄layer on Co foil through anodization was prepared as cathode for nitro-group reduction and electrodeposited with Pd particles for dechlorination to reduce CAP completely. After 3 h treatment, almost 100% of CAP was reduced. Co²⁺ions in Co₃O₄served as catalytic sites for electrons transfer to CAP through a redox circle Co²⁺-Co³⁺-Co²⁺, which triggered nitro-group reduction at first. With the presence of Pd particles, more atomic H* were generated for dechlorination, which increased 22% of reduction efficiency after 3 h treatment. Therefore, a better capacity was achieved by Pd/Co₃O₄cathode (K = 0.0245 min^-1,Kis reaction constant) than by other cathodes such as Fe/Co₃O₄(K = 0.0182 min^-1), Cu/Co₃O₄(K = 0.0164 min^-1), and pure Co₃O₄(K = 0.0106 min^-1). From the proposed reaction pathway, the ultimate product was carbonyl-reduced AM (dechlorinated aromatic amine product of CAP) without antibacterial activity, which demonstrated this cathodic technology was a feasible way for wastewater pre-treatment.

Heterogeneous activation of persulfate by Mg doped Ni(OH)2 for efficient degradation of phenol

Mg doped Ni(OH)₂ was synthesized and investigated as an efficient material to activate persulfate (PS) for phenol degradation. The property of the Ni(OH)₂ material was enhanced by Mg doping as the removal efficiency of phenol was increased from 74.82 % in Ni(OH)₂/PS system to 89.53 % in Mg-doped Ni(OH)₂/PS system within 20 min. Such a high removal efficiency revealed that doping Mg into Ni(OH)₂ brings about more defects (oxygen vacancies), which facilitated the formation of more active species in the degradation process. The removal efficiencies of phenol increased with the increase of the initial pH from 3 to 11. The influences of Cl^-, NO₃^- and HCO₃^- on the stability of the system were also studied and the results showed that removal rates of all systems in the presence of these different inorganic anions could reached about 90 % within 20 min. Based on the electron spin resonance (ESR) experiments, ¹O₂, O₂^·-, ·OH and SO₄^•- were identified as the active species in Mg-doped Ni(OH)₂/PS system for phenol degradation and a degradation mechanism was proposed for this system. In addition, the as-prepared material retained its activation performance even after 3 repeated cycles.

Alkylpolyglycoside modified MnFe2O4 with abundant oxygen vacancies boosting singlet oxygen dominated peroxymonosulfate activation for organic pollutants degradation

A novel alkylpolyglycoside (APG)-modified MnFe₂O₄ nanocomposite (APG@MnFe₂O₄) enriched with oxygen vacancies (VOs) was developed via co-precipitation and characterized as a peroxymonosulfate (PMS) activator to degrade 2,4-dichlorophenol (2,4-DCP) as the model contaminant. The APG effectively promoted the in situ formation of VOs on MnFe₂O₄ and subsequently enhanced the production of singlet oxygen (¹O₂). Furthermore, the APG@MnFe₂O₄ initialized an even more efficient non-radical pathway and dominated the degradation of 2,4-DCP. The constructed APG@MnFe₂O₄ exhibited a much higher reaction rate constant (0.0522) by ~12.73 times of that of the bare MnFe₂O₄ (0.0041). The degradation efficiency of 2,4-DCP in the APG@MnFe₂O₄/PMS system approached 93% within 90 min, a rate significantly higher than that in the MnFe₂O₄/PMS system (32%) given the same condition. The reasonable catalytic mechanism can be attributed to the Fe/Mn/VOs species. The APG@MnFe₂O₄ also exhibits universally high removal activity for various pollutants and excellent cyclic stability. Thus, the APG@MnFe₂O₄ is a promising PMS activator, and its utilization offers a useful strategy for developing VOs-enriched MnFe₂O₄ catalysts as a means of eliminating organic pollutants from wastewater.

Diclofenac degradation based on shape-controlled cuprous oxide nanoparticles prepared by using ionic liquid

Persulfate oxidation technology is widely used in wastewater treatment, but there are still many disadvantages, such as high energy consumption, side reaction and narrow pH applicability. Copper oxides can activate persulfate steadily with higher efficiency. In this paper, a novel preparation method of shape-controlled cuprous oxide (Cu₂O) nanoparticles featured with high catalytic performance was explored. It was found that adding ionic liquid 1-butyl-3-methylimidazolium bromide ([BMIM]Br) during preparation of Cu₂O can improve the degradation rate of diclofenac (DCF). Cu₂O nanoparticles possess good stability in consecutive cycling tests, which was confirmed by X-ray photoelectron spectroscopy. The possible mechanism of Cu₂O activating persulfate at different initial pH conditions was discussed based on electron paramagnetic resonance spin-trapping experiment. It was found that DCF was efficiently degraded in the Cu₂O/peroxydisulfate (PDS) system within a broad pH range from 5 to 11. It proved via a quenching experiment that the activation process of PDS mainly occurs on the surface layer of Cu₂O nanoparticles. As a result, shape-controlled Cu₂O nanoparticles prepared by ionic liquid are expected to be used for in situ chemical oxidation, which is an effective oxidation processes to degrade DCF remaining in surface water and ground water.

Different activation methods in sulfate radical-based oxidation for organic pollutants degradation: Catalytic mechanism and toxicity assessment of degradation intermediates

With the continuous development of industrialization, a growing number of refractory organic pollutants are released into the environment. These contaminants could cause serious risks to the human health and wildlife, therefore their degradation and mineralization is very critical and urgent. Recently sulfate radical-based advanced oxidation technology has been widely applied to organic pollutants treatment due to its high efficiency and eco-friendly nature. This review comprehensively summarizes different methods for persulfate (PS) and peroxymonosulfate (PMS) activation including ultraviolet light, ultrasonic, electrochemical, heat, radiation and alkali. The reactive oxygen species identification and mechanisms of PS/PMS activation by different approaches are discussed. In addition, this paper summarized the toxicity of degradation intermediates through bioassays and Ecological Structure Activity Relationships (ECOSAR) program prediction and the formation of toxic bromated disinfection byproducts (Br-DBPs) and carcinogenic bromate (BrO₃^-) in the presence of Br^-. The detoxification and mineralization of target pollutants induced by different reactive oxygen species are also analyzed. Finally, perspectives of potential future research and applications on sulfate radical-based advanced oxidation technology in the treatment of organic pollutants are proposed.

Efficient activation of peroxymonosulfate by Co-doped mesoporous CeO2 nanorods as a heterogeneous catalyst for phenol oxidation

Sulfate radical-based advanced oxidation processes have received considerable attentions in the remediation of organic pollutants due to their high oxidation ability. In this study, a novel Co3O4/CeO2 catalyst was fabricated and employed as a peroxymonosulfate (PMS) activator to generate SO4•- for phenol degradation. The Co3O4/CeO2 catalyst exhibited a good catalytic performance at a wide pH range of 3.4 to 10.8, and 100% phenol (20 mg/L) was removed within 50-min reaction under optimal conditions with 0.2 g/L catalyst and 2.0 g/L PMS at room temperature. The transformation products and total organic carbon during the degradation process were also determined. The quenching experiments and electron paramagnetic resonance spectra revealed that sulfate radical (SO4•-) rather than other species such as singlet oxygen (1O2) and hydroxyl radical (•OH) was primarily responsible for phenol degradation in the Co3O4/CeO2/PMS system, and a rational mechanism was proposed. Moreover, the recycling experiments as well as low cobalt leaching concentration manifested satisfactory reusability and stability. The effects of various inorganic anions and natural organic matter in real water matrix on phenol oxidation were further evaluated. We believe that the Co3O4/CeO2 composites have promising applications of PMS activation for the degradation of organic pollutants in wastewater treatment.

Electrochemical sensor based on the Mn3O4/CeO2 nanocomposite with abundant oxygen vacancies for highly sensitive detection of hydrogen peroxide released from living cells

Based on the strategy of increasing the number of oxygen vacancies to improve the catalytic performance, we have developed a novel electrochemical sensor based on the multivalent metal oxides cerium dioxide and manganous oxide (Mn₃O₄/CeO₂) for reliable determination of extracellular hydrogen peroxide (H₂O₂) released from living cells. The Mn₃O₄/CeO₂ nanocomposite was characterized by high-resolution transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The electrochemical performance of the Mn₃O₄/CeO₂ nanocomposite modified glassy carbon electrode (Mn₃O₄/CeO₂/GCE) was investigated. Owing to the abundant oxygen vacancies and strong synergistic effect between the multivalent Ce and Mn, the sensor exhibited excellent catalytic activity and selectivity for the electrochemical detection of H₂O₂ with a low quantitation limit of 2 nM. Moreover, Mn₃O₄/CeO₂/GCE exhibited excellent reproducibility, repeatability, and long-term storage stability. Because of these remarkable analytical advantages, the constructed sensor was able to determine H₂O₂ released from living cells with satisfactory results. The results showed that the Mn₃O₄/CeO₂ sensor is a promising candidate for a nanoenzymatic H₂O₂ sensor with the possibility of applications in physiology and diagnosis.

Heterogeneous activation of peroxydisulfate by sulfur-doped g-C3N4 under visible-light irradiation: Implications for the degradation of spiramycin and an assessment of N-nitrosodimethylamine formation potential

In this study, peroxydisulfate (PDS) was activated by synthesized sulfur-doped g-C₃N₄ (SCN) under visible-light irradiation and was adopted to enhance the removal of spiramycin, which is an important precursor of N-nitrosodimethylamine (NDMA). Specifically, 95.4% of spiramycin (≤10 mg/L) was removed in 60 min under the conditions of an initial value of pH of 7.0, an SCN dose of 1.0 g/L, and a PDS dose of 200 mg/L, and its degradation fitted well with the pseudo first-order kinetics. Electron paramagnetic resonance analysis and trapping experiments confirmed that ·O₂^- and h⁺ were the main oxidizers for the degradation of spiramycin, and ·SO₄^- and ·OH also participated in the removal of spiramycin. The removal of spiramycin in the PDS/SCN visible-light catalytic system occurred through three different pathways: aldehyde oxidation, cleavage of C-O bond and demethylation. Notably, 61.4% of NDMA formation potential (FP) was reduced after the reaction. The SCN catalyst was stable and its catalytic performance was excellent in the PDS/SCN system, as the spiramycin removal efficiency decreased only slightly from 95.4% to 87.3% after being reused three times. Therefore, our study not only provides an alternative method for removing spiramycin but can also can significantly reduce NDMA FP.

Mechanism insight into efficient peroxydisulfate activation by novel nano zero-valent iron anchored yCo3O4 (nZVI/yCo3O4) composites

Novel nano zero-valent iron anchored bio-matrix supported Co₃O₄ (nZVI/yCo₃O₄) composites were fabricated for tetracycline (TC) efficient degradation by activating peroxydisulfate (PS). The systematical characterizations verified that the nZVI/yCo₃O₄ composites with magnetism have higher surface area than yCo₃O₄ and pure Co₃O₄, contributing to more accessible active sites. Various catalytic parameters (nZVI mass ratio, leached ions, initial pH, catalyst dosage, PS concentration and coexisting anions) were thoroughly investigated. In nZVI/yCo₃O₄/PS system, 97.6 %, 93.4 % and 77.3 % TC were degraded within 15 min at pH 3.0, 6.0 and 9.0, respectively. Based on four successive degradation runs, the excellent mineralization rate and reusability of nZVI/yCo₃O₄ composites were mainly benefited from the suppressed metals leaching. The PS activated mechanisms were proposed as non-radicals (¹O₂) dominated pattern at acidic conditions and radicals (SO₄-) predominant pattern at alkaline environment, which may be highly related to the electron donating capacity of nZVI at different pH and the M^(n + 1)+/Mⁿ⁺ redox cycling between Fe or Co metal. The plausible degradation routes of TC were presented based on the detected intermediates. Overall, the synthesized heterogeneous nZVI/yCo₃O₄ composites can efficiently active PS at a wide pH range, and further broaden the application of Co-based catalysts in PS activation.

Application of copper tailings combined with persulfate for better removing methyl orange from wastewater

In this paper, wasted copper tailings (CT) were used to activate persulfate (PS) to degrade azo dye methyl orange (MO). The results show that a large amount of FeS₂ contained in CT can slowly release Fe²⁺ in the aqueous solution to activate PS to generate reactive oxygen species to degrade MO. When the dosage of CT and PS was 2 g/L and 3 mM respectively, the MO degradation efficiency of 20 mg/L in the CT/PS system was 96.52% within 60 min. At the same time, it is found that CT has a certain adsorption capacity for MO, and the intra-particle diffusion model can well describe the adsorption process of MO by CT. The effects of related reaction parameters (CT dosage, PS dosage, initial MO concentration and solution pH) on MO degradation in CT/PS system were investigated. Compared with the direct addition of an equal amount of Fe²⁺ as in the CT/PS system, for homogeneous activated PS to degrade MO (Fe²⁺/PS), the results showed that the degradation efficiency of Fe²⁺/PS system for MO was lower than that of CT/PS system due to excessive Fe²⁺ consumption of SO₄ ^·-. By comparing the Fe²⁺ and Fe³⁺ concentrations in the two systems, it was found that the CT/PS system could maintain a low Fe²⁺ concentration during the reaction process, and the Fe²⁺ released by CT could be used by PS to degrade MO more efficiently. The free radical scavenging experiments showed that the reactive oxygen species in the CT/PS system was mainly SO₄ ^·-. This study not only proposed a new CT utilization approach, but also solved the problem of reduced degradation efficiency of organic pollutants caused by excessive Fe²⁺ in the Fenton-like reaction.

Ce-based catalysts used in advanced oxidation processes for organic wastewater treatment: A review

Refractory organic pollutants in water threaten human health and environmental safety, and advanced oxidation processes (AOPs) are effective for the degradation of these pollutants. Catalysts play vital role in AOPs, and Ce-based catalysts have exhibited excellent performance. Recently, the development and application of Ce-based catalysts in various AOPs have been reported. Our study conducts the first review in this rapid growing field. This paper clarifies the variety and properties of Ce-based catalysts. Their applications in different AOP systems (catalytic ozonation, photodegradation, Fenton-like reactions, sulfate radical-based AOPs, and catalytic sonochemistry) are discussed. Different Ce-based catalysts suit different reaction systems and produce different active radicals. Finally, future research directions of Ce-based catalysts in AOP systems are suggested.

Synergistic effect of persulfate and g-C3N4 under simulated solar light irradiation: Implication for the degradation of sulfamethoxazole

A method combining g-C₃N₄ and potassium peroxydisulfate (PDS) under simulated sunlight was put forward to effectively degrade sulfamethoxazole (SMX). The SMX removal efficiency was substantially improved compared with the processes involving only g-C₃N₄ or PDS. The kinetic constants for the g-C₃N_4, PDS and g-C₃N₄/PDS systems were 0.0023, 0.0239 and 0.068 min^-1, respectively. The g-C₃N₄/PDS process reached an SMX removal rate of 98.4 % after 60 min of simulated sunlight; in addition, the proposed system showed desirable efficiency for SMX degradation in two different actual water samples as well. The reaction mechanism was illustrated by trapping experiments, which showed that g-C₃N₄ can promote S₂O₈^2- to transfer SO₄^-, S₂O₈^2- favored the generation of O₂^-, and O₂^-, SO₄^- and holes (h⁺) were the main oxidative species for the SMX degradation in the combined reaction process under simulated sunlight. Then, to further explore this mechanism, the intermediates generated during the combined reaction process were analyzed by LC/MS and possible degradation pathways were proposed. The result showed that the breaking of the SN and C-S bonds, the hydroxylation of the benzene ring and the oxidation of the amino group were identified as the main pathways in the SMX degradation process by the g-C₃N₄/PDS system under simulated sunlight.

CuO and CeO2 assisted Fe2O3/attapulgite catalyst for heterogeneous Fenton-like oxidation of methylene blue

In this paper, CuO and CeO₂ were screened as co-catalyst components for Fe₂O₃/attapulgite (ATP) catalyst, and three new catalysts (CuO–Fe₂O₃/ATP, CeO₂–Fe₂O₃/ATP and CuO–CeO₂–Fe₂O₃/ATP) were prepared for degradation of methylene blue (MB). The three catalysts' characteristics were determined by BET, XRD, FT-IR, SEM and XPS. MB degradation in different systems and at different pH values was also studied. Under the conditions of H₂O₂ concentration of 4.9 mmol L⁻¹, catalyst dosage of 5 g L⁻¹, pH of 5, reaction temperature of 60 °C and MB initial concentration of 100 mg L⁻¹, the as-synthesized catalysts showed much greater reaction rate and degradation efficiency of MB than Fe₂O₃/ATP catalyst. In addition, the reusability of the as-prepared composites was evaluated. The intermediate products of MB degradation were identified by LC-MS and the possible degradation process of MB was put forward.

A novel heterogeneous catalyst CuO–CeO₂–Fe₂O₃/ATP was synthesized for MB degradation and the catalytic mechanism was put forward.

A High-Efficiency CuO/CeO2 Catalyst for Diclofenac Degradation in Fenton-Like System

An efficient Fenton-like catalyst CuO/CeO₂ was synthesized using ultrasonic impregnation and used to remove diclofenac from water. The catalyst was characterized by N₂ adsorption-desorption, SEM-EDS, XRD, HRTEM, Raman, and XPS analyses. Results showed that CuO/CeO₂ possessed large surface area, high porosity, and fine elements dispersion. Cu was loaded in CeO₂, which increased the oxygen vacancies. The exposed crystal face of CeO₂ (200) was beneficial to the catalytic activity. The diclofenac removal experiment showed that there was a synergistic effect between CuO and CeO₂, which might be caused by more oxygen vacancies generation and electronic interactions between Cu and Ce species. The experimental conditions were optimized, including pH, catalyst and H₂O₂ dosages, and 86.62% diclofenac removal was achieved. Diclofenac oxidation by ·OH and adsorbed oxygen species was the main mechanism for its removal in this Fenton-like system.

Application of Photocatalytic Falling Film Reactor to Elucidate the Degradation Pathways of Pharmaceutical Diclofenac and Ibuprofen in Aqueous Solutions

Diclofenac (DCF) and ibuprofen (IBP) are common pharmaceutical residues that have been detected in the aquatic system. Their presence in the aquatic environment has become an emerging contaminant problem, which has implications for public health. The degradation pathway and identification of transformation products of pharmaceutical residues are crucial to elucidate the environmental fate of photocatalytic decomposition of these pollutants in aqueous media. The degradation process might lead to creation of other possible emerging contaminates. In this study, the degradation of DCF and IBP in aqueous solutions was investigated. To this end, coated TiO2 on a Pilkington Active glass was used as a photocatalyst under UVA illumination, in a planar falling film reactor. Pilkington ActivTM glass was used as a photocatalyst and a falling liquid film generator. Degradation kinetics of both pharmaceuticals followed a pseudo-first-order model. The transformation products of both diclofenac and ibuprofen during the degradation process were detected and identified with gas chromatography–mass spectrometry (GC–MS) and ion chromatography. The results showed that the mineralization rate of both pharmaceuticals through photocatalysis was very low. Low chain carboxylic acids, such as formic, acetic, oxalic, malonic, and succinic acids were the main by-products. A pathway of DCF and IBP degradation was proposed.

Chitosan Grafted Adsorbents for Diclofenac Pharmaceutical Compound Removal from Single-Component Aqueous Solutions and Mixtures

The main purpose of this study was to investigate the synthesis of some cross-linked carboxyl-grafted chitosan derivatives to be used as selective adsorbents for diclofenac (DCF) pharmaceutical compounds from aqueous mixtures. Four different materials were synthesized using succinic anhydride (CsSUC), maleic anhydride (CsMAL), itaconic acid (CsITA), and trans-aconitic acid (CsTACON) as grafting agents. After synthesis, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) were performed before and after DCF adsorption. In addition, a complete adsorption evaluation was carried out for all materials studying some important parameters. The optimum pH was 4; the amino groups of DCF can be protonated at pH = 4 (–NH⁺), so this groups can easily attract the clear negatively carboxyl moieties (–COO⁻) of the chitosan adsorbents. The Q_m for CsTACON was higher than those of the other materials, at all temperatures studied. By altering the temperature from 25 to 35 °C, an increase (16%) of Q_m (from 84.56 to 98.34 mg g⁻¹) was noted, while similar behavior was revealed after a further increase of temperature from 35 to 45 °C, improving by 5% (from 98.34 to 102.75 mg g⁻¹). All isotherms were fitted to Langmuir, Freundlich, and Langmuir-Freundlich (L-F) models). In addition, a kinetic model was proposed taking into account not only the interactions but also the diffusivity of the molecule (DCF) into the polymeric network. The behavior of the prepared chitosan materials in simultaneously removing other compounds (synergetic or antagonistic) was also evaluated by experiments performed in mixtures. DCF presented the highest removal from the mixture in the order: CsTACON (92.8%) > CsITA (89.5%) > CsSUC (80.9%) > CsMAL (66.2%) compared to other pharmaceutical compounds (salicylic acid, ibuprofen and ketoprofen). Desorption was achieved by using different eluants (either water or organic). The highest desorption ability was found for acetone (100% for CsTACON, CsSUC, CsMAL and 77% for CsITA) for all materials.