A review on recent developments in the adsorption of surfactants from wastewater

Exploring the defense strategies of benzalkonium chloride exposures on the antioxidant system, photosynthesis and ROS accumulation in Lemna minor

With the advent of technological advancements post the industrial revolution, thousands of chemicals are introduced into the market annually to enhance different facets of human life. Among these, pharmaceutical and personal care products (PPCPs), including antibiotics and disinfectants, such as benzalkonium chlorides (BACs), are prominent. BACs, often used for surface and hand disinfection in high concentrations or as preservatives in health products such as nasal sprays and eye drops, may present environmental risks if they seep into irrigation water through prolonged exposure or improper application. The primary objective of this study is to elucidate the tolerance mechanisms that may arise in Lemna minor plants, known for their remarkable capability to accumulate substances efficiently, in response to exogenously applied BACs at varying concentrations. The study applied six different concentrations of BACs, ranging from 0.25 to 10 mg L-1. The experimental period spanned seven days, during which the treatments were conducted in triplicate to ensure reliability and reproducibility of the results. It was observed that low concentrations of BACs (0.25, 0.5 and 1 mg L-1) did not elicit any statistically significant changes in growth parameters. However, higher concentrations of BACs (2.5, 5, and 10 mg L-1) resulted in a reduction in RGR by 20%, 28%, and 36%, respectively. Chlorophyll fluorescence declined significantly at BAC doses of 5 and 10 mg L-1, with Fv/Fm ratios decreasing by 9% and 15%, and Fv/Fo ratios by 40% and 39%, respectively. Proline content decreased in all treatment groups, with a 46% reduction at 10 mg L-1 BAC. TBARS and H2O2 contents increased proportionally with BAC dosage, showing the highest increases of 30% and 40% at 10 mg L-1, respectively. The noticeable increase in SOD enzyme activity at BAC concentrations of 0.5, 1, and 2.5 mg L-1, with increases of 2.7-fold, 2.2-fold, and 1.7-fold respectively, along with minimal accumulation of H2O2, suggests that L. minor plants have a strong tolerance to BAC. This is supported by the efficient functioning of the CAT and GST enzymes, especially evident at the same concentrations, where increased activities effectively reduce the buildup of H2O2. In the AsA-GSH cycle, although variations were observed between groups, the contribution of the GR enzyme to the preservation of GSH content by recycling GSSG likely maintained redox homeostasis in the plant, especially at low concentrations of BACs. The study revealed that L. minor effectively accumulates BAC alongside its tolerance mechanisms and high antioxidant activity. These results underscore the potential for environmental cleanup efforts through phytoremediation.

Interaction of Pb(II) with microplastic-sediment complexes: Critical effect of surfactant

In this study, the impact of surfactants on the adsorption behavior of Pb(II) onto microplastics-sediment (MPs-S) complexes was investigated. Firstly, virgin polyamide (VPA) and polyethylene (VPE) were placed in Xiangjiang River sediment for six months to conduct in-situ aging. The results indicated that the biofilm-developed polyamide (BPA) and polyethylene (BPE) formed new oxygen-containing functional groups and different biofilm species. Furthermore, the adsorption capacity of Pb(II) in sediment (S) and MPs-S complexes was in the following order: S > BPA-S > VPE-S > VPA-S > BPE-S. The addition of sodium dodecyl benzenesulfonate (SDBS) promoted the adsorption of Pb(II), and the adsorption amount of Pb(II) increased with the higher concentration of SDBS, while adding cetyltrimethylammonium bromide (CTAB) showed the opposite result. The adsorption process of MPs-S complexes to Pb(II) was dominated by chemical adsorption, and the interaction between MPs-S complexes and Pb(II) was multilayer adsorption involving physical and chemical adsorption when the surfactants were added. Besides, the pH exerts a significant effect on Pb(II) adsorption in different MPs-S complexes, and the highest adsorption amount occurred at pH 6. Noteworthy, CTAB promoted the adsorption ability of Pb(II) when the exogenous FA was added. The binding characteristic of sediment endogenous DOM components and Pb(II) was influenced by the addition of MPs and surfactants. Finally, it confirmed that adsorption mechanisms mainly involve electrostatic and hydrophobic interaction. This study provides a new perspective to explore the environmental behaviors of Pb(II) by MPs and sediments with the addition of surfactants, which was conducive to evaluating the ecological risks of MPs and heavy metals in aquatic environments.

Tricks and tracks of prevalence, occurrences, treatment technologies, and challenges of mixtures of emerging contaminants in the environment: With special emphasis on microplastic

This paper aims to emphasize the occurrence of various emerging contaminant (EC) mixtures in natural ecosystems and highlights the primary concern arising from the unregulated release into soil and water, along with their impacts on human health. Emerging contaminant mixtures, including pharmaceuticals, personal care products, dioxins, polychlorinated biphenyls, pesticides, antibiotics, biocides, surfactants, phthalates, enteric viruses, and microplastics (MPs), are considered toxic contaminants with grave implications. MPs play a crucial role in transporting pollutants to aquatic and terrestrial ecosystems as they interact with the various components of the soil and water environments. This review summarizes that major emerging contaminants (ECs), like trimethoprim, diclofenac, sulfamethoxazole, and 17α-Ethinylestradiol, pose serious threats to public health and contribute to antimicrobial resistance. In addressing human health concerns and remediation techniques, this review critically evaluates conventional methods for removing ECs from complex matrices. The diverse physiochemical properties of surrounding environments facilitate the partitioning of ECs into sediments and other organic phases, resulting in carcinogenic, teratogenic, and estrogenic effects through active catalytic interactions and mechanisms mediated by aryl hydrocarbon receptors. The proactive toxicity of ECs mixture complexation and, in part, the yet-to-be-identified environmental mixtures of ECs represent a blind spot in current literature, necessitating conceptual frameworks for assessing the toxicity and risks with individual components and mixtures. Lastly, this review concludes with an in-depth exploration of future scopes, knowledge gaps, and challenges, emphasizing the need for a concerted effort in managing ECs and other organic pollutants.

Surfactant-mediated bio-manufacture: A unique strategy for promoting microbial biochemicals production

Biochemicals are widely used in the medicine and food industries and are more efficient and safer than synthetic chemicals. The amphipathic surfactants can interact with the microorganisms and embed the extracellular metabolites, which induce microbial metabolites secretion and biosynthesis, performing an attractive prospect of promoting the biochemical production. However, the commonness and differences of surfactant-mediated bio-manufacture in various fields are largely unexplored. Accordingly, this review comprehensively summarized the properties of surfactants, different application scenarios of surfactant-meditated bio-manufacture, and the mechanism of surfactants increasing metabolites production. Various biochemical productions such as pigments, amino acids, and alcohols could be enhanced using the cloud point and the micelles of surfactants. Besides, the amphiphilicity of surfactants also promoted the utilization of fermentation substrates, especially lignocellulose and waste sludge, by microorganisms, indirectly increasing the metabolites production. The increase in target metabolites production was attributed to the surfactants changing the permeability and composition of the cell membrane, hence improving the secretion ability of microorganisms. Moreover, surfactants could regulate the energy metabolism, the redox state and metabolic flow in microorganisms, which induced target metabolites synthesis. This review aimed to broaden the application fields of surfactants and provide novel insights into the production of microbial biochemicals.

Sustainable application of surfactants in soil remediation: Selective pollutants adsorption and hydrogen peroxide-driven adsorbent regeneration

The uncontrolled disposal of the liquid lindane wastes have led to the formation of dense non-aqueous phase liquids (DNAPL), consisting of 28 chlorinated organic compounds (COCs), contaminating soil and groundwater. Surfactant-enhanced aquifer remediation is proposed as technology to treat these sites. However, the polluted emulsion generated must be manged on-site. In this work a two-step process is applied to treat emulsion composed of E-Mulse® 3 (4 g·L-1) as surfactant and a DNAPL (2 gCOCs·L-1). In the first, the COCs were selectively adsorbed in a granular activated carbon (GAC) column with Fe (II) previously adsorbed (10-20mg·g-1) onto the carbon surface, recovering an aqueous phase with surfactant for their reuse. In the second step, the spent GAC was regenerated with a 40 g·L-1 solution of hydrogen peroxide fed to the column at 2 mL·min-1 to promote the oxidation of the COCs adsorbed in the GAC. The kinetic and adsorption model in a multisolute (surfactant and DNAPL) system has been proposed. Five successive cycles of regeneration/adsorption have been successfully applied in the column process. About 50 % of the COCs were retained from the emulsion, and more than 70 % of the surfactant was recovered. The consumption of unproductive oxidants decreased with the number of regeneration cycles. The water effluent obtained after regeneration of GAC did not present chlorinated compounds desorbed and nontoxic by-products generated, such as short-chain acids.

Effects of sodium dodecylbenzene sulfonate (SDBS) on zebrafish (Danio rerio) gills and blood

Sodium dodecylbenzene sulfonate (SDBS) is an important surfactant used as a cleaning agent and industrial additive to remove unwanted chemicals which have been detected in the aquatic environment. The aim of this study was to examine the toxicological potential of SDBS on the gills of adult male zebrafish (Danio rerio) exposed to this chemical. For the 96 hr acute exposure, fish were divided into three groups: control, 0.25 mg/L, and 0.5 mg/L of SDBS. After the experiment, morphophysiological analyses (gill histopathology and histochemistry), oxidative stress (determination of gill activities of superoxide dismutase (SOD) and catalase (CAT)), and hematological analyses (leukocyte differentiation) were conducted. Data demonstrated that SDBS at both tested concentrations altered the histopathological index and initiated circulatory disturbances, as well as adverse, progressive, and immunological changes in the gills. In the 0.5 mg/L group, SOD activity decreased significantly, but CAT activity was not altered. Prominent blood changes observed in this group were neutrophilia and lymphocytosis. The number of mucous and chloride cells increased significantly in both groups. Taken together, our findings demonstrated that exposure of D. rerio to SDBS, even for 96 hr, produced adverse morphological and hematological effects associated with a reduction in SOD activity. Our findings indicate that exposure of aquatic species to the anionic surfactant SDBS may lead to adverse consequences associated with oxidative stress. Therefore, this study highlights the risks that this substance may pose to aquatic ecosystems and emphasizes the need for further investigations and strict regulations on its disposal.

Comparative Analysis of Hydrogel Adsorption/Desorption with and without Surfactants

In this particular study, a hydrogel known as SAP-1 was synthesized through the grafting of acrylic acid-co-acrylamide onto pullulan, resulting in the creation of Pul-g-Poly (acrylic acid-co-acrylamide). Additionally, a sponge hydrogel named SAP-2 was prepared by incorporating the surfactant sodium dodecyl benzene sulfonate (SDBS) into the hydrogel through free radical solution polymerization. To gain further insight into the composition and properties of the hydrogels, various techniques, such as Fourier transform infrared spectroscopy, hydrogen nuclear magnetic resonance (1H NMR), atomic absorption spectroscopy, and field emission scanning electron microscopy (FE-SEM), were employed. Conversely, the absorption kinetics and the equilibrium capacities of the prepared hydrogels were investigated and analyzed. The outcomes of the investigation indicated that each of the synthesized hydrogels exhibited considerable efficacy as adsorbents for cadmium (II), copper (II), and nickel (II) ions. In particular, SAP-2 gel displayed a remarkable cadmium (II) ion absorption ability, with a rate of 190.72 mg/g. Following closely, SAP-1 gel demonstrated the ability to absorb cadmium (II) ions at a rate of 146.9 mg/g and copper (II) ions at a rate of 154 mg/g. Notably, SAP-2 hydrogel demonstrated the ability to repeat the adsorption-desorption cycles three times for cadmium (II) ions, resulting in absorption capacities of 190.72 mg/g, 100.43 mg/g, and 19.64 mg/g for the first, second, and third cycles, respectively. Thus, based on the abovementioned results, it can be concluded that all the synthesized hydrogels possess promising potential as suitable candidates for the adsorption and desorption of cadmium (II), copper (II), and nickel (II) ions.

Synthesis of WS42- Intercalated NiZnAl LDHs as Effective Adsorbents to Remove Copper Ions from Water

A series of WS42- intercalated NiZnAl ternary-layered double-hydroxides (LDHs) with various Ni/Zn ratios were synthesized by an ion-exchange method and used as adsorbents to remove Cu2+ from water. The introduction of Zn produced ZnS on the surface of LDHs. The LDH with the Ni/Zn/Al molar ratio of 0.1/1.9/1 showed the best adsorption ability. Cu2+ ions are removed via three routes: forming [Cu-WS4]n- complexes via soft acid-soft base interaction between WS42- and Cu2+, isomorphic substitution of Zn2+ in sheets by Cu2+, and cation exchange of Cu2+, with ZnS on the surface of LDHs. With the increased Cu2+ concentration, the complexes dominated the adsorption because polynuclear [Cu-WS4]n- complexes with high Cu/W ratios (2-6) may be formed. Cu+ is present in such complexes, which is produced by the internal redox. Even at Cu2+ concentration up to 600 mg·L-1, neither amorphous CuWS4 nor decreased interlayer distance was observed. Contrarily, the interlayer distance was slightly enlarged due to forming bigger [Cu-WS4]n- complexes. The adsorption followed the pseudo-second-order kinetics and Langmuir isotherm model. The experimental maximum adsorption capacity reached 555.4 mg·g-1.

Selective stepwise adsorption for enhanced removal of multi-component dissolved organic chemicals from petrochemical wastewater

The coexistence of multi-component dissolved organic chemicals causes tremendous challenge in purifying petrochemical wastewater, and stepwise selective adsorption holds the most promise for enhanced treatments. This study is designed to enhance the removal of multiple dissolved organic chemicals by stepwise adsorption. Special attention is given to the selective removal mechanisms for the major pollutant N,N-dimethylformamide (DMF), the sensitive pollutant fluorescent dissolved organic matter (FDOM) and other components. The results indicated that the combination of coal activated carbon and aluminum silica gel produced a synergistic effect and broke the limitation of removing only certain pollutants. Combined removal rates of 80.5 % for the dissolved organic carbon and 86.7 % for the biotoxicity in petrochemical wastewater were obtained with the enhanced two-step adsorption. The adsorption performance of both adsorbents remained stable even after five cycles. The selective adsorption mechanism revealed that hydrophobic organics such as DMF was adsorbed by the macropores of coal activated carbon, while the FDOM was eliminated by π-π stacking, electrostatic interaction and hydrophobic interaction. The hydrophilic organics were removed by the mesopores of aluminum silica gel, the silica hydroxyl groups and hydrophilic interaction. This study provides a comprehensive understanding of the selective adsorption mechanism and enhanced stepwise removal of multiple pollutants in petrochemical wastewater, which will guide the deep treatment of complex wastewater.

Integrated physicochemical processes to tackle high-COD wastewater from pharmaceutical industry

Wastewater decontamination in pharmaceuticals is crucial to prevent environmental and health risks from API residues and other contaminants. Advanced oxidation processes (AOPs) combined with cavitational treatments offer effective solutions. Challenges include designing reactors on a large scale and monitoring the effectiveness and synergies of the hybrid technology. In the present work, pilot-scale treatment of a real high COD (485 g/L) pharmaceutical wastewater (PW) was investigated using hydrodynamic cavitation (HC) operated individually at 330 L/h or in combination with oxidants and electrical discharge (ED) with cold plasma (15 kV and 48 kHz). The first approach consisted of PW cavitational treatment alone of 7 L of 1:100 diluted PW at a HC-induced pressure of 60 bar and a flow rate of 330 L/h. However, this strategy did not provide satisfactory results for COD (∼15% less), and only when HC treatment was extended to more than 30 min in a recirculation mode, encouraging results were obtained (∼45% COD reduction). Consequently, a hybrid approach combining HC with ED-cold plasma was chosen to treat this high-COD PW. Aiming to establish an efficient flow-through hybrid process, after optimising all cavitation and electrical discharge parameters (45 bar HC pressure and 10 kHz ED frequency), the best COD abatement of ∼50 % was recorded with a 1:50 diluted PW. However, a subsequent adsorption step over activated carbon was required to achieve an almost quantitative COD reduction (95%+). Our integrated physicochemical process proved to be extremely efficient in treating high-COD industrial wastewater and resulted in a remarkable reduction of the COD value. In addition, the residual surfactants content in the PW were also drastically reduced (98%+) when a small amount of oxidants was added in the hybrid HC/ED treatment.

Superhydrophobic Nanoparticles: An Efficiently Selective Adsorbent for Surfactant-Like Contaminants from Complex Wastewater Matrices

Surfactant-like contaminants (SLCs) with distinctive amphiphilic structures have become a global concern in wastewater due to their toxicity and persistency. Despite extensive efforts, achieving efficient and selective SLCs removal remains challenging because of their wide range of molecular weights and complex functional group compositions. Superhydrophobic nanoparticles can potentially tackle this challenge by targeting the long oleophilic chains of SLCs. However, conventional contact angle measurements hinder hydrophobicity characterization and corresponding selectivity research because of the powder morphology of nanoparticles. Herein, the authors offered information regarding the distribution of water molecular probes in surfaces and proposed a quantitative characterization approach based on low-field nuclear magnetic resonance. Through synthesizing superhydrophobic and hydrophilic polydopamine nanospheres with similar morphologies, the selective adsorption potential of superhydrophobic nanoparticles for SLCs is systematically demonstrated. As revealed by the interaction mechanisms, the superhydrophobic surface of nanospheres increased its affinity and selectivity for SLCs adsorption by enhancing hydrophobic interactions. Superhydrophobic modification achieved ten times the adsorption capacity of sodium dodecyl benzene sulfonate, an exemplified surfactant, compared with pristine nanoparticles. By regulated self-polymerization, the superhydrophobic nanospheres are coated onto the surface of a 3D sponge and enable efficient selective SLCs adsorption from highly polluted leachate matrices with long-term stability and reusability.

Strategies of managing solid waste and energy recovery for a developing country - A review

Solid waste is considered one of the major pollutants of both water and surface worldwide. The growing global population, urban expansion, and industrial growth are the main reasons for solid waste generation. This has become a major challenge with both regional and worldwide consequences. The yearly generation of municipal solid wastes around the world is 2.01 BT (billion tons) among which about 33 % are not ecologically handled. To address this, proper solid waste management, especially recycling waste products, is crucial to achieving sustainability. High-income countries are able to recycle 51 % of their waste, while low-income countries only recycle 16 % of their waste. Inadequate solid waste management practices can only compound environmental and social problems. To handle these issues thermochemical and biochemical methods are used to convert solid waste to energy. Thermochemical method is suitable for developing countries though it is energy extensive. This review provides a detailed analysis of developing countries' solid waste management and energy recovery. It explores energy recovery technologies, including thermochemical and biochemical waste conversion processes.

Neodothiora pruni sp. nov., a Biosurfactant-Producing Ascomycetous Yeast Species Isolated from Flower of Prunus mume

A yeast strain, designated as JAF-11T, was isolated from flower of Prunus mume Sieb. et Zucc. in Gwangyang, Republic of Korea. Phylogenetic analysis showed that strain JAF-11T was closely related to Neodothiora populina CPC 39399T with 2.07 % sequence divergence (12 nucleotide substitutions and three gaps in 581 nucleotides) in the D1/D2 domain of the large subunit (LSU) rRNA gene, and Rhizosphaera macrospora CBS 208.79T with 4.66 % sequence divergence (25 nucleotide substitutions and five gaps in 535 nucleotides) in the internal transcribed spacer (ITS) region. Further analysis based on the concatenated sequences of the D1/D2 domain of the LSU rRNA gene and the ITS region confirmed that strain JAF-11T was well-separated from Neodothiora populina CPC 39399T. In addition to the phylogenetic differences, strain JAF-11T was distinguished from its closest species, Neodothiora populina CPC 39399T and Rhizosphaera macrospora CBS 208.79T belonging to the family Dothioraceae by its phenotypic characteristics, such as assimilation of carbon sources. Hence, the name Neodothiora pruni sp. nov. is proposed with type strain JAF-11T (KACC 48808T; MB 850034).

Surfactants in water and wastewater (greywater): Environmental toxicity and treatment options

Surfactant, an emerging pollutant present in greywater, raises the toxicity levels in the water body. Soap, detergent, and personal care items add surfactant to greywater. Due to excessive washing and cleaning procedures brought on by the COVID-19 pandemic, the release of surfactants in greywater has also increased. Considering the environmental toxicity and problems it creates during the treatment, it's essential to remove surfactants from the wastewater. This review intends to explain and address the environmental toxicity of the surfactant released via greywater and current techniques for surfactant removal from wastewater. Various physical, chemical, and biological methods are reported. Modern adsorbents such as hydrophilic silica nanoparticles, chitosan, fly ash, and iron oxide remove surfactants by adsorption. Membrane filtration effectively removes surfactants but is not cost-effective. Coagulants (chemical and natural coagulants) neutralize surfactant charges and help remove them as bigger particles. Electrocoagulation/electroflotation causes surfactants to coagulate and float. Microorganisms break down surfactants in microbial fuel cells to generate power. Surfactants are removed by natural processes and plants in constructed wetlands where traditional aerobic and anaerobic approaches use microbes to break down surfactants. Constructed wetlands, natural coagulation-flocculation, and microbial fuel cells are environmentally beneficial methods to remove surfactants from wastewater.

Spring water quality monitoring using multiple bioindicators from multiple collection sites

The aim of this study was to examine the water quality of the Extrema River spring in a Brazilian Cerrado area. Three collection sites (P1 - P3) were sampled in the dry and rainy seasons, which are close to industries from different sectors. In the physicochemical analysis, a decrease in dissolved oxygen levels (<5 mg/L) and pH (< 6) at P3 was detected. An increase in heterotrophic bacteria count was recorded at all sites (> 500 colonies/ml). In ecotoxicological analyses, P2 and P3 exhibited toxicity using Vibrio fischeri (> 20%). In evaluating toxicity, the reduction in seed germination was significant utilizing Lactuca sativa at all locations and with Allium cepa only at P2; rootlet length was decreased at P3 on L. sativa and at all sites with A. cepa. In contrast, loss of membrane integrity and mitochondrial function of meristems was adversely affected at all locations using both L. sativa and A. cepa assays. Principal components analysis (PCA) approach indicated that seasonality apparently did not markedly interfere with the obtained data, but it is important to include more collection locations to be evaluated with multiple bioindicators in the spring region. Our data indicate the urgent need for more rigorous programs to monitor the discharge of effluents into water springs.

Study on removal of phosphorus and COD in wastewater by sinusoidal AC Fenton oxidation-coagulation

In order to treat domestic wastewater containing phosphorus and chemical oxygen demand (COD), the new technology of Sinusoidal Alternating Current (AC) Fenton Oxidation-Coagulation (SACFOC) was used to improve the removal efficiency (Re) and reduce energy consumption (EEC). The morphology, elemental composition, crystal structure and functional groups of the sludge were characterised by Scanning Electron Microscope (SEM), Energy-dispersive X-ray Spectroscopy (EDS), X-ray diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). The results show that total phosphorus removal efficiency {Re(TP)} and removal efficiency of organic matter {Re(COD)} can reach 97.56% and 87.77%, respectively, but EEC is only 0.09 kWh·m-3 under the optimum conditions of pH0 = 3, current density (j) = 0.5 A·m-2, c0(TP) = 18 mg·dm-3, c0(COD) = 300 mg·dm-3, c0(H2O2) = 0.06 mol·dm-3, t = 45 min. As compared with direct current (DC) Fenton Oxidation-Coagulation (DCFOC), the COD removal efficiency of SACFOC treatment was improved by 37%, but the energy consumption was reduced by 45%. The degradation process of total phosphorus and COD by SACFOC abides by the quasi-first-order kinetic model. The process of SACFOC includes double effects of electrocoagulation of iron sol by electrolysis and degrade COD by oxidation of formed hydroxyl radicals (·OH) in wastewater, which improves removal efficiency of total phosphorus and COD in wastewater. Our research findings will provide technical guidance and a theoretical basis for the simultaneous treatment of wastewater containing phosphorus and COD applying SACFOC process.

Removal of microfiber and surfactants from household laundry washing effluents by powdered activated carbon: kinetics and isotherm studies

Domestic laundry wastewater discharge contributes significantly to the presence of microfiber and surfactant pollutants in aquatic ecosystems, which have detrimental and toxic effects on humans and the environment. Investigating the efficacy of powdered activated carbon (PAC) in removing micro-/nanofibers with or without surfactant from household laundry effluent is the purpose of the current research. To simulate real-world scenarios, PAC adsorption kinetics and isotherms in laundry effluents under controlled conditions were studied. These studies showed that the kinetics obeyed a pseudo-second-order process and the isotherms varied between Langmuir and Freundlich models depending on the water types. In the results of experiments using distilled water and tap water, it was observed that the adsorption capacity was higher in tap water. When the adsorption of 0.1 μm filtered synthetic garments, detergent, and tap water was compared with the adsorption of the raw sample, it was observed that the adsorption capacity of the 0.1 μm filtered version was higher. Even though this study is preliminary, the results indicate that PAC has the capacity to serve as a viable approach for mitigating micro-/nanoplastic and surfactant contamination from laundry wastewater, thereby offering valuable guidance for advancing eco-friendly laundry techniques.

Surface modification of quartz sand: A review of its progress and its effect on heavy metal adsorption

Quartz sand (SiO₂) is a prevalent filtration medium, boasting wide accessibility, superior stability, and cost-effectiveness. However, its utility is often curtailed by its sleek surface, limited active sites, and swift saturation of adsorption sites. This review outlines the prevalent strategies and agents for quartz sand surface modification and provides a comprehensive analysis of the various modification reagents and their operative mechanisms. It delves into the mechanism and utility of surface-modified quartz sand for adsorbing heavy metal ions (HMIs). It is found that the reported modifiers usually form connections with the surface of quartz sand through electrostatic forces, van der Waals forces, pore filling, chemical bonding, and/or molecular entanglement. The literature suggests that these modifications effectively address issues inherent to natural quartz sand, such as its low superficial coarseness, rapid adsorption site saturation, and limited adsorption capacity. Regrettably, comprehensive investigations into the particle size, regenerative capabilities, and application costs of surface-modified quartz sand and the critical factors for its wider adoption are lacking in most reports. The adsorption mechanisms indicate that surface-modified quartz sand primarily removes HMIs from aqueous solutions through surface complexation, ion exchange, and electrostatic and gravitational forces. However, these findings were derived under controlled laboratory conditions, and practical applications for treating real wastewater necessitate overcoming further laboratory-scale obstacles. Finally, this review outlines the limitations of partially surface modified quartz sand and suggests potential venues for future developments, providing a valuable reference for the advancement of cost-effective, HMI-absorbing, surface-modified quartz sand filter media.

Linear alkylbenzene sulfonate threats to surface waters at the national scale: A neglected traditional pollutant

Freshwater biodiversity and ecosystem services might decline due to exposure to chemicals. However, researchers have devoted much attention to the potential risks of emerging contaminants, while placing less effort on historical pollutants, such as the surfactant, linear-alkylbenzene-sulfonate (LAS), which is a major component of widely used synthetic detergents worldwide. In this study, a multilevel risk assessment approach was used to assess risks posed by LAS to aquatic organisms, on a wide spatial scale, based on various assessment endpoints. Additionally, bottom-up approaches were used to assess contributions of LAS source discharges to aquatic environments. Concentrations of LAS in surface waters of China ranged from less than the limit of detection to 14,200 μg/L. The predicted no effect concentration (PNEC) based on adverse effects on reproduction is 15 μg/L, which is slightly less than the PNEC based on other endpoints. 99% of surface waters in Chaohu Lake and the Hai River (Ch: Haihe) were predicted to pose a risk to growth of aquatic organisms, with a protection threshold of 5% of species (HC₅). Discharges of LAS were estimated using activity data and emission factors for 280 major cities in the basin. Rural domestic sources were the main source of LAS to surface waters. These outcomes provided a process for developing comprehensive management and control approaches to help researchers and policymakers effectively manage water resources affected by increasing concentrations of LAS.

Environmental concentrations of surfactants as a trigger for climax of horizonal gene transfer of antibiotic resistance

Ubiquitous antibiotic resistance genes (ARGs) is a significant global human health concern. Surfactants have been extensively used worldwide, and the consumption of surfactants containing hygiene, cleaning agents and disinfectants was multiplied during COVID-19 pandemic, which have caused significantly increased pollution of surfactants in aquatic environment. Whether such ever-increasing surfactant concentration boost dissemination risk of ARGs still remains unknown. Here the effects of three typical surfactants such as sodium dodecyl sulfate, cetyltrimethylammonium bromide and benzalkonium chloride on the transformation of pUC19 plasmid (2686 bp)-borne ARGs to recipient bacteria E. coli DH5ɑ were investigated. It was found that these surfactants at environmental concentrations facilitated horizonal gene transfer (HGT) via transformation. The transformation triggering concentrations for the three surfactants were 0.25-0.34 mg/L with a maximum increased transformation frequency of 13.51-22.93-fold. The mechanisms involved in activated HGT of ARGs via transformation triggered by surfactants could be mainly attributed to the increased production of reactive oxygen species, which further enhanced cell membrane permeability. These findings provide new sights for understanding of ARG propagation and also imply that the drastic rise of surfactant concentration in aquatic environment may significantly increase the dissemination risk of antibiotic resistance.

Identification of key surfactant in municipal solid waste leachate foaming and its influence mechanism

Serious foaming problems and the excessive consumption of defoamer have undoubtedly become one of the most critical problems that hinder municipal solid waste (MSW) leachate treatment efficiency and industry development. Since there is limited research penetrating the foaming mechanism and identification of the key surfactants, current defoaming and surfactant removal techniques lack pertinence and orientation. In this study, a foaming characterization device was developed and ultra-performance liquid chromatography-tandem mass spectrometry (UPLC/MS/MS) was optimized to accurately identify the key surfactants affecting leachate foaming and offer a glimpse into their interaction mechanisms. This study collected leachate samples from 9 typical landfills and waste-to-energy facilities of various waste compositions, climatic conditions, ages, and geographical locations. The foaming problem of leachate was mainly centered on raw leachate and nanofiltration membrane concentrate (NFC). Fresh leachate performed with relatively low foaming capacity and foam stability, associated with low surfactant concentration. The pH value of the system was positively correlated with the concentration of anionic surfactants, indicating significant impacts on surfactant release in MSW. Since the distribution characteristics of linear alkylbenzene sulfonate (LAS) in leachate were consistent with the variety of foaming performances, LAS proved to be an indispensable surfactant in the leachate involved in this study, and its content proportion escalated to 92.87% in aged leachate.

Recent Advances in the Preparation of Delivery Systems for the Controlled Release of Scents

Scents are volatile compounds highly employed in a wide range of manufactured items, such as fine perfumery, household products, and functional foods. One of the main directions of the research in this area aims to enhance the longevity of scents by designing efficient delivery systems to control the release rate of these volatile molecules and also increase their stability. Several approaches to release scents in a controlled manner have been developed in recent years. Thus, different controlled release systems have been prepared, including polymers, metal-organic frameworks and mechanically interlocked systems, among others. This review is focused on the preparation of different scaffolds to accomplish a slow release of scents, by pointing out examples reported in the last five years. In addition to discuss selected examples, a critical perspective on the state of the art of this research field is provided, comparing the different types of scent delivery systems.

Coaxial Electrospun Nanofibrous Membranes for Enhanced Water Recovery by Direct Contact Membrane Distillation

Membrane distillation (MD) is an emerging technology for water recovery from hypersaline wastewater. Membrane scaling and wetting are the drawbacks that prevent the widespread implementation of the MD process. In this study, coaxially electrospun polyvinylidene fluoride-co-hexafluoropropylene (PVDF-co-HFP) nanofibrous membranes were fabricated with re-entrant architecture and enhanced hydrophobicity/omniphobicity. The multiscale roughness was constructed by incorporating Al2O3 nanoparticles and 1H, 1H, 2H, 2H Perfluorodecyltriethoxysilane in the sheath solution. High resolution transmission electron microscopy (HR-TEM) could confirm the formation of the core-sheath nanofibrous membranes, which exhibited a water contact angle of ~142.5° and enhanced surface roughness. The membrane displayed a stable vapor flux of 12 L.m−2.h−1 (LMH) for a 7.0 wt.% NaCl feed solution and no loss in permeate quality or quantity. Long-term water recovery from 10.5 wt.% NaCl feed solution was determined to be 8−10 LMH with >99.9% NaCl rejection for up to 5 cycles of operation (60 h). The membranes exhibited excellent resistance to wetting even above the critical micelle concentration (CMC) for surfactants in the order sodium dodecyl sulphate (SDS) (16 mM) > cetyltrimethylammonium bromide (CTAB) (1.5 mM) > Tween 80 (0.10 mM). The presence of salts further deteriorated membrane performance for SDS (12 mM) and Tween-80 (0.05 mM). These coaxial electrospun nanofibrous membranes are robust and can be explored for long-term applications.

Antarctic granite rocks as wastewater surfactant degradation catalysts

Antarctica seawater surrounding research stations has been impacted by antibiotics, formaldehydes, surfactants, heavy metals, sunscreen chemicals, and coliforms. The removal of surfactants from water is challenging since biological approaches are ineffective at mineralizing organic molecules. To evaluate the effectiveness of an advanced oxidation process (AOP) on the degradation of surfactants at the "Pedro Vicente Maldonado" research station of Ecuador, the performance of Antarctic granite rocks as catalysts and hydrogen peroxide (H₂O₂) as an oxidant was researched. Following the coagulation-flocculation process, the AOP reduced the concentration of surfactant by 90 %, from 19.50 mg/L to 0.97 mg/L. This short communication summarizes initial research on a low-cost wastewater treatment that could be used to degrade surfactants after coagulation-flocculation processes.

Environmental impact assessment of nanofluids containing mixtures of surfactants and silica nanoparticles

Due to widespread use of nanoparticles in surfactant-based formulations, their release into the environment and wastewater is unavoidable and toxic for biota and/or wastewater treatment processes. Because of concerns over the environmental impacts of nanofluids, studies of the fate and environmental impacts, hazards, and toxicities of nanoparticles are beginning. However, interactions between nanoparticles and surfactants and the biodegradability of these mixtures have been little studied until now. In this work, the environmental impacts of nanofluids containing mixtures of surfactants and silica nanoparticles were valuated. The systems studied were hydrophilic silica nanoparticles (sizes 7 and 12 nm), a nonionic surfactant (alkyl polyglucoside), an anionic surfactant (ether carboxylic acid), and mixtures of them. The ultimate aerobic biodegradation and the interfacial and adsorption properties of surfactants, nanoparticles, and mixtures during biodegradation were also evaluated. Ultimate biodegradation was studied below and above the CMCs of the individual surfactants. The interfacial and adsorption properties of surfactant solutions containing nanoparticles were influenced by the addition of silica particles. It was determined that silica nanoparticles reduced the capability of the nonionic surfactant alkyl polyglucoside to decrease the surface tension. Thus, silica NPs promoted a considerable increase in the surfactant CMC, whereas the effect was opposite in the case of the anionic surfactant ether carboxylic acid. Increasing concentrations of surfactant and nanoparticles in the test medium caused decreases in the maximum levels of mineralization reached for both types of surfactants. The presence of silica nanoparticles in the medium reduced the biodegradability of binary mixtures containing nonionic and anionic surfactants, and this effect was more pronounced for larger nanoparticles. These results could be useful in modelling the behaviour of nanofluids in aquatic environments and in selecting appropriate nanofluids containing nanoparticles and surfactants with low environmental impact.

Graywater treatment of emerging pollutant linear alkylbenzene sulfonate by adsorption with leather shave waste activated carbon

The purpose of this research is to evaluate the use of leather shave waste activated carbon (ACLW) as an alternative for the treatment of wastewater containing linear alkylbenzene sulfonate (LAS). Batch adsorption tests were carried out (pH effect, isotherms, kinetics). The activated carbon was tested for its life cycle by desorption with solvent and it was further evaluated as real wastewater treatment for bath graywater. Under the optimum pH of 2.5, kinetic studies showed a better correlation with the pseudo-second order model, with an activation energy of 27.5 kJ mol-1. Equilibrium isotherms correlated better with the double layer model, indicating hemi-micelle formation and performing a high-affinity isotherm. Adsorption was shown to be endothermic (∆H0 =  + 73.89 kJ mol-1), entropy driven (∆S0 =  + 0.46 kJ mol-1 K-1), and occurring spontaneously. The use of ethanol solution was effective for the regeneration of the adsorbent. Adsorption was applied in real wastewater, removing contaminants from bath graywater, especially anionic surfactants with up to 95% removal efficiency.

Adsorption characteristics of antibiotics on microplastics: The effect of surface contamination with an anionic surfactant

Microplastics and antibiotics are common, typical pollutants, and they can cause compound pollution where they coexist in the environment. Surfactants in the environment can change the interface characteristics of pollutants, and then drive the change of environmental behavior of pollutants. In this paper, we studied the physicochemical properties of complexes of polystyrene (PS) and polyethylene (PE) contaminated with sodium dodecyl benzene sulfonate (SDBS); the complexes are referred to as SPS and SPE, respectively. Taking oxytetracycline (OTC) and norfloxacin (NOR) as representatives of broad-spectrum antibiotics, the effects of SDBS on the adsorption behavior of PS and PE were analyzed and possible mechanisms were proposed. The results showed that SDBS could effectively combine with PS and PE to enhance the surface electronegativity and reduce the Brunner-Emmett-Teller (BET) specific surface area and porosity. The crystal structure remained basically unchanged, and the surface functional groups changed slightly. SDBS greatly enhanced the saturated adsorption capacities of PS and PE for OTC and NOR, and made adsorption easier, which reduced the Gibbs free energy of the adsorption system. The adsorption behaviors of SPS and SPE for the two antibiotics were consistent with the Elovich kinetic model and Sips isothermal model. SDBS enhanced the hydrophilicity of the microplastics, which facilitated their adsorption of antibiotics dissolved in water. SDBS could directly combine with antibiotics to form a complex, further increasing the adsorption capacity of the microplastics for antibiotics. The -SO₃H in SDBS could combine with oxygen-containing functional groups and -NH₂ in OTC and NOR. Non-ionic covalent bonds, electrostatic interactions, and hydrophobic attraction between the alkyl chain and benzene ring also played a role in adsorption. SDBS made it possible for MPs to load more types and quantities of pollutants and change their preferential adsorption selectivity, which significantly aggravated the environmental hazards.

Sustainable conversion of saturated adsorbents (SAs) from wastewater into value-added products: future prospects and challenges with toxic per- and poly-fluoroalkyl substances (PFAS)

Following circular economy principles, the reuse or recycling of saturated adsorbents (SAs or adsorbate-laden adsorbents) into a low-cost engineered product is a valuable alternative to eliminate secondary pollution after adsorption. This review evaluates the application of SAs for the generation of products that can serve as (i) antimicrobial agents or disinfectants, (ii) materials for civil construction, (iii) catalysts, (iv) fertilizers, and (v) secondary adsorbents. The importance of SAs configuration in terms of functional groups, surface area and pore morphology played a crucial role in their reutilization. The SAs-laden silver ions (Ag⁺) strongly inhibit (~ 99%) the growth of Escherichia coli and Staphylococcus aureus microbes found in drinking and wastewaters. The intra-solidification of SAs containing toxic metal pollutants (As³⁺ and F^-) with cementitious materials can effectively reduce their leaching below permissible limits of USEPA standards for their utility as additives in construction work. The existence of transition metal ions (Cu²⁺, Cr^3+/6+, Ni²⁺) on the surface of SAs boosted activity and selectivity towards the desired product during catalytic oxidation, degradation, and conversion processes. The thermally recycled SAs can assist in the secondary adsorption of pollutants from another waste solution due to a larger surface area (> 1000 m²g^-1). However, there are chances that the SAs discussed above will contain traces of PFAS. The article summarizes the challenges, performance efficacy, and future prospects at the end of each value-added product. We also highlight critical challenges for managing PFAS-laden SAs and stimulate new perspectives to minimize PFAS in air, water, and soils.

Comprehensive review of the interfacial behavior of water/oil/surfactant systems using dissipative particle dynamics simulation

A comprehensive understanding of interfacial behavior in water/oil/surfactant systems is critical to evaluating the performance of emulsions in various industries, specifically in the oil and gas industry. To gain fundamental knowledge regarding this interfacial behavior, atomistic methods, e.g., molecular dynamics (MD) simulation, can be employed; however, MD simulation cannot handle phenomena that require more than a million atoms. The coarse-grained mesoscale methods were introduced to resolve this issue. One of the most effective mesoscale coarse-grained approaches for simulating colloidal systems is dissipative particle dynamics (DPD), which bridges the gap between macroscopic time and length scales and molecular-scale simulation. This work reviews the fundamentals of DPD simulation and its progress on colloids and interface systems, especially surfactant/water/oil mixtures. The effects of temperature, salt content, a water/oil ratio, a shear rate, and a type of surfactant on the interfacial behavior in water/oil/surfactant systems using DPD simulation are evaluated. In addition, the obtained results are also investigated through the lens of the chemistry of surfactants and emulsions. The outcome of this comprehensive review demonstrates the importance of DPD simulation in various processes with a focus on the colloidal and interfacial behavior of surfactants at water-oil interfaces.

Green Chemistry Based Gold Nanoparticles Synthesis Using the Marine Bacterium Lysinibacillus odysseyi PBCW2 and Their Multitudinous Activities

Green chemistry has paved an 'avant-garde avenue' in the production and fabrication of eco-friendly stable nanoparticles employing the utilization of biological agents. In the present study we present the first report on the potential of the marine bacterium Lysinibacillus odysseyi PBCW2 for the extracellular production of gold nanoparticles (AuNPs). Utilizing a variety of methods, AuNPs in the cell-free supernatant of L. odysseyi (CFS-LBOE) were identified and their antioxidant, antibacterial, and dye-degrading properties were examined. The visual coloring of the reaction mixture to a ruby red hue showed the production of LBOE-AuNPs; validated by means of XRD, TEM, SEM, XRD, DLS, TGA, and FT-IR analysis. Additionally, the 2,2-diphenyl-1-picrylhydrazyl technique and the well diffusion assay were used to examine their dose-dependent antioxidant and antibacterial activity. These biogenic LBOE-AuNPs showed 91% dye degradation efficiency during catalytic reduction activity on BTB dye, demonstrating their versatility as options for heterogeneous catalysis.

Efficient Removal of Organic Dye from Aqueous Solution Using Hierarchical Zeolite-Based Biomembrane: Isotherm, Kinetics, Thermodynamics and Recycling Studies

Bio adsorbents have received tremendous attention due to their eco-friendly, cheap and non-toxic nature. Recently, bio-adsorbent-based membranes have been frequently employed for water treatment. The work reports the preparation of a novel adsorbent membrane from hierarchical zeolite, polyvinyl alcohol, carboxymethyl cellulose and agar. The fabricated membrane was characterized spectroscopically and microscopically with several techniques such as XRD, UTM, TGA, optical microscopy and FT-IR, as well as contact-angle studies. The result showed that the hierarchical-zeolite-loaded membrane is superior in terms of thermal stability, mechanical properties and surface roughness. The fabricated membrane was investigated for its efficiency in the removal of Congo red dye in aqueous conditions. The influence of pH, temperature, contact period and the initial concentration of dye and zeolite loading on the adsorption process are also explored. The adsorption results highlighted the maximum sorption property of Congo red on agar/zeolite/carboxymethyl cellulose/polymer biomembrane was found to be higher (15.30 mg/g) than that of zeolite powder (6.4 mg/g). The adsorption isotherms and kinetic parameters were investigated via Langmuir, Freundlich and pseudo-first order, pseudo-second order and the intraparticle diffusion model, respectively. The adsorption isotherms fitted well for both considered isotherms, whereas pseudo-second order fitted well for kinetics. The thermodynamic parameter, ΔG at 303 K, 313 K and 323 K was −9.12, −3.16 and −0.49 KJ/mol, respectively. The work further explores the antibacterial efficacy of the prepared membrane and its reusability.

An overview on surfactants as pollutants of concern: Occurrence, impacts and persulfate-based remediation technologies

Surfactants are molecules that reduce interfacial energy and increase solubility of other pollutants in water. These properties make them suitable for various domestic and industrial applications, soil remediation, pesticide formulation, among others. The increase in their use and the lack of strict regulations regarding their disposal and management is a matter of concern and requires more attention since the release and distribution of these compounds into the environment can modify important water quality parameters. As a result of these changes, different toxicological effects to aquatic organisms are discussed and exposed herein. On this basis, we provide an overview of the classes of surfactants, as well as their occurrence in different aqueous matrices. In addition, existing regulations around the world regarding their concentration limit for different environments are discussed. Current research focuses on the application of conventional treatments, such as biological treatments; notwithstanding, more toxic and bioaccumulative products can be generated. Advanced Oxidation Processes are promising alternatives and have also been widely applied for the removal of surfactants. This study provides, for the first time, an overview of the application of persulfate-based processes for surfactants degradation based on recent literature findings, as well as the various factors related to the activation of the persulfate anions. This review also highlights the challenges and opportunities for future research to overcome the obstacles to the practical application of this process.

Phosphorus removal and recovery: state of the science and challenges

Phosphorus is one of the main nutrients required for all life. Phosphorus as phosphate form plays an important role in different cellular processes. Entrance of phosphorus in the environment leads to serious ecological problems including water quality problems and soil pollution. Furthermore, it may cause eutrophication as well as harmful algae blooms (HABs) in aquatic environments. Several physical, chemical, and biological methods have been presented for phosphorus removal and recovery. In this review, there is an overview of phosphorus role in nature provided, available removal processes are discussed, and each of them is explained in detail. Chemical precipitation, ion exchange, membrane separation, and adsorption can be listed as the most used methods. Identifying advantages of these technologies will allow the performance of phosphorus removal systems to be updated, optimized, evaluate the treatment cost and benefits, and support select directions for further action. Two main applications of biochar and nanoscale materials are recommended.

Application of Water Hyacinth Biomass (Eichhornia crassipes) as an Adsorbent for Methylene Blue Dye from Aqueous Medium: Kinetic and Isothermal Study

Water pollution has generated the need to develop technologies to remove industrial pollutants. Adsorption has been recognized as one of the most effective techniques for effluent remediation. In this study, parts (stem and leaves) of a problematic aquatic weed, the water hyacinth (Eichhornia crassipes), were separated to produce a bioadsorbent. The objective was to evaluate the adsorption of a cationic dye, methylene blue (MB), in an aqueous solution of the biomass from different parts of the water hyacinth (Eichhornia crassipes) plants. The materials were characterized through techniques of infrared spectroscopy, scanning electron microscopy, X-ray diffractometry, and thermogravimetric analysis, before and after the material adsorption. Water hyacinth biomasses presented adsorption capacity above 89%, and the kinetics was faster for stem biomass. The kinetic study found that the adsorption process is better described by the pseudo-second-order model, and the adjustments of the isotherm experimental data indicated that both materials are favorable for adsorption. Therefore, water hyacinth bioadsorbent represents a renewable resource with potential for effluent treatment.

Comparative Life-Cycle Cost Analysis of Alternative Technologies for the Removal of Emerging Contaminants from Urban Wastewater

Emerging contaminants (ECs) continue to threaten our fragile ecosystem, yet their mitigation remains limited by economic factors. Meanwhile, a relatively expensive material, Graphene Oxide (GO), has shown promise as a solution for EC removal following further development into three graphene-based materials (GBMs): Porous graphene adsorbent (PGa), Graphene-oxide foam adsorbent (GOFa), and the hybrid filter. Due to the nuances of each synthesis process, financial costs will differ throughout the GBMs’ life cycle which have been quantified and compared in the present work at a range of possible breakthrough times. Finally, economic and environmental costs have been combined for each technology to compare eco-efficiency. Results demonstrated a substantial economic advantage of the GBMs when compared to alternative technologies, most notably the GOFa filter that incurred the lowest life-cycle costs at $1.73 ± 0.09/m3. This was mainly attributed to the lower demand of GOFa on the most expensive material required for material synthesis, hydrazine. In addition, the material demands of GOFa were more evenly distributed which suggest a higher resilience of the overall costs to price hikes of individual materials required for synthesis. In terms of eco-efficiency the GOFa filter also demonstrated the greatest improvement when compared to the reference technology These results have provided robust total investment costs for several technologies that can now offer contrast to other EC-removal solutions.

Recent Review of Titania-Clay-Based Composites Emerging as Advanced Adsorbents and Photocatalysts for Degradation of Dyes over the Last Decade

Textile industry being one of the most flourishing industries keeps growing and developing every year, and the consequences are not very pleasant. Even though its contribution towards economy of a country is indisputable, there are many pros and cons associated with it that should not be brushed aside, one of them being textile dye waste which is also growing at alarming rate. Many techniques have been designed to deal with this environmental crisis including adsorption and photodegradation of dye waste by various substances, both natural and synthetic. TiO2 and clay both have gained immense popularity in this area. Over the last decade, many successful attempts have been made to design TiO2-clay-based composites to combine and make the most of their individual capabilities to degrade textile dye waste. While clay is an effective adsorbent, inexpensive, innocuous, and a great ion exchanger, TiO2 provides supplementary active sites and free radicals and speeds up the degradation rate of dyes. This review summarizes various features of TiO2-clay-based composites including their surface characteristics, their role as dye adsorbents and photocatalysts, challenges in their implementation, and modifications to overcome these challenges made over the last decade.

The role of sodium dodecyl sulfate mediated hydrothermal synthesis of MoS2 nanosheets for photocatalytic dye degradation and dye-sensitized solar cell application

The novel properties and exciting behavior of two-dimensional nanosheet-based materials have piqued the interest of research all over the world. In this study, bulk molybdenum disulfide (bulk MoS₂) and sodium dodecyl sulfate-mediated molybdenum disulfide nanosheets (MoS₂-SDS NS) were synthesized via a facile sonication and hydrothermal process. The findings from the characterization revealed that the addition of sodium dodecyl sulfate (SDS) surfactant reduces the crystal phase and changes the structural morphology of bulk MoS₂. Furthermore, the photocatalytic and photovoltaic performance of bulk MoS₂ and MoS₂-SDS NS were also investigated. The results show that by using methylene blue dye, the photocatalytic efficiency increased from 56.30% to 91.84% at 150 min under UV-Visible light irradiation, and the photo-conversion efficiency (PEC (%)) of the dye-sensitized solar cell increased from 1.47% to 3.81% for bulk MoS₂ and MoS₂-SDS NS, respectively. Finally, we discussed in-depth the effect of SDS surfactants on MoS₂, which can improve their photovoltaic and photocatalytic performance.

Surfactant-induced adsorption of Pb(II) on the cracked structure of microplastics

Surfactant molecules can change the hydrophobic nature of microplastic surfaces, thereby affecting the adsorption of heavy metals in the environment onto the microplastics. It is essential to explore the role of crack structure of microplastics in the adsorption of heavy metals, especially in the presence of surfactants. In this study, polyethylene (PE) and polypropylene (PP) were evaluated for Pb(II) adsorption and desorption mechanism in the presence of two surfactants: cetyltrimethylammonium bromide (CTAB) and sodium dodecylbenzenesulfonate (SDBS). The experimental results were analyzed using kinetics and the isothermal model fitting and spectrogram (FTIR, XPS). This study showed that the application of surfactants could greatly enhance the Pb(II) adsorption capacities of PE and PP by promoting Pb(II) into the fissures. The Pb(II), S, and N contents did not significantly decrease at different depths in the presence of surfactants, and the Pb(II) content without surfactants decreased with an increasing depth. The adsorption behavior was consistent with the Bangham channel diffusion model and the DR model, suggesting that the adsorption process was related to the pore structure of the microplastics. Furthermore, the release of Pb(II) from desorption using high concentration of surfactant solution was less than that of low concentration, it was difficult to release heavy metals primarily because of the crack structure of the microplastics, especially when more surfactant molecules entered the pores. This work contributes to a better understanding of the adsorption mechanism of heavy metals on microplastics in the presence of surfactants, which will better control the ecological risks of microplastics.

Ecotoxicological impacts caused by high demand surfactants in Latin America and a technological and innovative perspective for their substitution

Nowadays, water pollution represents a great concern due to population growth, industrialization, and urbanization. Every day hazardous chemical products for humans and aquatic organisms are disposed of arbitrarily from homes and industries. Even though detergents are considered an essential market, there is evidence of environmental impacts caused by surfactants like nonylphenol ethoxylate (NPE) and linear alkylbenzene sulfonates (LAS). Regulations about maximum allowable concentrations in sewage, surface water, and drinking water are scarce or null, mostly in developing countries like Latin American countries. Therefore, this review explores these two common toxic surfactants (NPE and LAS) and proposes a technological, innovative, and ecological perspective on detergents. Also, it establishes a starting point for industries to minimize adverse effects on humans and environmental health caused by these compounds.

Removal of Copper(II) in the Presence of Sodium Dodecylobenzene Sulfonate from Acidic Effluents Using Adsorption on Ion Exchangers and Micellar-Enhanced Ultrafiltration Methods

The selective removal of Cu(II) in the presence of sodium dodecylobenzene sulfonate from acidic effluents was made using the adsorption and micellar-enhanced ultrafiltration methods. Lewatit MonoPlus TP220 showed the best adsorption behavior in the systems containing Cu(II) in the presence of ABSNa50 surfactant compared to the other adsorbents (removal efficiency ≈ 100%, sorption capacity ≈ 10 mg/g). The kinetics followed the pseudo-second order kinetic equation. The Langmuir adsorption capacities were 110 mg/g (the system with ABSNa50 above CMC) and 130.38 mg/g (the system with ABSNa50 below CMC). The working ion exchange capacities were Cw = 0.0216 g/mL and Cw = 0.0135 g/mL. The copper removal by the micellar-enhanced ultrafiltration method was 76.46% (0.1 mol/L HCl).