Cr (VI) reduction by photocatalyic process: Nb2O5 an alternative catalyst

Hierarchically Periodic Macroporous Niobium Oxide Architecture for Enhanced Hydrogen Evolution

The fabrication of periodic macroporous (PM) in Nb2O5 via morphological control is crucial for improving the photocatalytic hydrogen evolution efficiency. In this study, Nb2O5 with PM is synthesized using a straightforward colloidal crystal templating approach. This material features an open, interconnected macroporous architecture with nanoscale walls, high crystallinity, and substantial porosity. Extensive characterization reveals that this hierarchically structured Nb2O5 possesses abundant surface active sites and is capable of capturing light effectively, facilitating rapid mass transfer and diffusion of reactants and markedly suppressing the recombination of photoexcited charge carriers. Macroporous Nb2O5 exhibits superior water-splitting hydrogen evolution performance compared with its bulk and commercial counterparts, achieving a hydrogen production rate of 405 µmol g-1 h-1, surpassing that of bulk Nb2O5 (B-Nb2O5) and commercial Nb2O5 (C-Nb2O5) by factors of 5 and 33, respectively. This study proposes an innovative strategy for the design of hierarchically structured PM, thereby significantly advancing the hydrogen evolution potential of Nb2O5.

Synchronously Enhanced Removal Ability and Stability of MXene through Biomimetic Modification

Increasing environmental problems intensify the demand for high-performance environmental purification materials. MXene is a typical transition-metal carbide/nitride material with a two-dimensional geometric feature and a good deal of functional groups, and it is considered as an efficient adsorbent for removing pollutants from wastewater. However, the easy oxidation and relatively low adsorption capacity greatly restrict its application. In this study, the MXene/polydopamine (PDA) composite particles were fabricated through the biomimetic modification method of inducing the self-polymerization of dopamine in an MXene aqueous solution. Microstructure characterizations demonstrate that PDA facilitates the exfoliation of MXene. Adsorption measurements show that MXene and PDA exhibit an apparent synergistic effect in removing chromium hexavalent Cr(VI) from aqueous solution, and more PDA content leads to a larger synergistic effect. Consequently, the composite particles exhibit an ultrahigh adsorption capacity (862.3 mg/g). Specifically, even if the composite particles were stored in aqueous solution for 2 months, they still exhibit high adsorption ability with only a 3.3% loss in adsorption capacity, indirectly confirming the enhanced stability of MXene induced by PDA. Furthermore, the composite particles also show reduction ability to Cr(VI) and about 54.3% Cr(VI) can be reduced to harmless chromium trivalent Cr(III). This study provides a new method for the preparation of MXene-based adsorbents with excellent adsorption capacity and high stability, which has broad application prospects in the field of wastewater treatment.

Synthesis of ZnO immobilized on recycled polyethylene terephtalate for sonocatalytic removal of Cr(VI) from synthetic, drinking waters and electroplating wastewater

In this study, Cr(VI) was removed sonocatalytically by the zinc oxide nanoparticle coated with polyethylene terephthalate (PET) fabricated through a facile co-precipitation method. The crystal structure, functional groups on the surface, morphology, surface composition and oxidation states of the nanomaterials were investigated by XRD, FTIR, SEM, EDX and XPS techniques. Environmental parameters including solution pH, catalyst dose, hexavalent chromium concentration, H₂O₂ content, purging gases, organic compounds and type and anions strength on the sonotocatalytic removal of Cr(VI) were also investigated. Additionally, the contribution of each process, reusability, Cr(VI) reduction from actual water and electroplating wastewater were evaluated. Under the optimal conditions, [Cr(VI)]₀=20 mg/L, nanocomposite loading=1.6 g/L and pH=5, 99.92% of Cr(VI) was removed within 60 min. By increaing, Cr(VI) concentration (5-50 mg/L), k_obs decreased to values between 0.1498 and 0.0063 min^-1 and the calculated electrical energy per order (E_Eo) increased from 148.68 to 3535.24 kWh.m^-3, respectively. The presence of purging gases, organic compounds and ionic strength negatively affected Cr(VI) reduction. Examination of radical scavengers showed that the most active radicals in Cr(VI) removal were O₂^•- and h⁺. The removal of the Cr(VI) using the US/ZnO-PET method (99.92%) was higher than that of the US/ZnO method (70.78%). The catalyst activity was well maintained up to eight consecutive cycles. In addition, the removal efficiency was approximately 72.23 and 68.55% for drinking water and real electroplating wastewater samples, respectively. The results of toxicity in the sonotocatalytic removal of Cr(VI) by Daphnia magna showed LC₅₀ and toxicity unit (TU) 48 h, which was equal to 81.46 and 1.227 vol percent.

Photoreduction of Cr(VI) in wastewater by anodic nanoporous Nb2O5 formed at high anodizing voltage and electrolyte temperature

In this study, nanoporous anodic film was produced by anodization of niobium, Nb in a fluoride ethylene glycol electrolyte. The effect of anodization voltage and electrolyte temperature was studied to find an optimum condition for circular, ordered, and uniform pore formation. The diameter of the pores was found to be larger when the applied voltage was increased from 20 to 80 V. The as-anodized porous film was also observed to comprise of nanocrystallites which formed due to high field-induced crystallization. The nanocrystallites grew into orthorhombic Nb₂O₅ after post-annealing treatment. The Cr(VI) photoreduction property of both the as-anodized and annealed Nb₂O₅ samples obtained using an optimized condition (anodization voltage: 60 V, electrolyte temperature: 70 °C) was compared. Interestingly, the as-anodized Nb₂O₅ film was found to display better photoreduction of Cr(VI) than annealed Nb₂O_5. However, in terms of stability, the annealed Nb₂O₅ presented high photocatalytic efficiency for each cycle whereas the as-anodized Nb₂O₅ showed degradation in photocatalytic performance when used continually.

MXene quantum dots decorated Ni nanoflowers for efficient Cr (VI) reduction

Nickel@MXene quantum dots (Ni@MQDs), as novel flower-like hybrid materials, were firstly prepared through a simple reduction method. The Ni@MQDs exhibited an outstanding catalytic performance for Cr (VI) reduction with a low activation energy (E_a = 18.9 kJ mol^-1) and a high kinetic constant (k = 0.4779 min^-1) in the presence of formic acid (HCOOH). Density functional theory calculations demonstrated that Ni@MQDs exhibited an upshift of d-band center of active Ni atoms to promote the adsorption of both HCOOH and active H atoms, as well as an improved conductivity to boost the catalytic reaction kinetics, leading to the most favorable catalytic performance. This work may open up a new avenue towards the design and synthesis of novel MQDs-based hybrid catalysts for wastewater treatment.

Functioned catalysts with magnetic core applied in ibuprofen degradation

In the present work, the performance of Ag/ZnO/CoFe₂O₄ magnetic photocatalysts in the photocatalytic degradation of ibuprofen (IBP) was evaluated. This study considered the use of pure Ag/ZnO (5% Ag) and also the use of the Ag/ZnO/CoFe₂O₄ magnetic catalysts containing different amounts (5, 10 and 15% wt) of cobalt ferrite (CoFe₂O₄). The catalysts were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoacoustic spectroscopy. To carry out the photocatalytic degradation reaction, different concentrations of the ibuprofen contaminant solution (10, 20 and 30 ppm) and different concentrations of photocatalyst were tested (0.3 g L^-1, 0.5 g L^-1 and 1.0 g L^-1). The reaction parameters studied were: IBP concentration, catalyst concentration, adsorption and photolysis, influence of the matrix, radiation source (solar and artificial) and the effect of organic additive. At the end of the photocatalytic tests, the best operating conditions were defined. Considering the obtained results of degradation efficiency and magnetic separation, the optimal parameters selected to proceed with the other tests of the study were: ibuprofen solution concentration 10 ppm, Ag/ZnO/CoFe₂O₄ (5%) catalyst at a concentration of 0.3 g L^-1 and pH 4.5 of the reaction medium. The results indicated the feasibility of magnetic separation of the synthesized catalysts. A long duration test indicated that the catalyst exhibits stability throughout the degradation reaction, as more than 80% of IBP was degraded after 300 minutes. The photocatalytic activity was directly affected by the ferrite load. The higher the nominal load of ferrite, the lower the performance in IBP degradation. It was also observed that the smallest amount of ferrite studied was enough for the catalyst to be recovered and reused. The adsorption and photolysis tests did not show significant results in the IBP degradation. In addition, it was possible to verify that the aqueous matrix, the use of solar radiation and the addition of additive (acid formic) were interfered directly in the process. The catalyst reuse tests indicated that it can be recovered and reused at least three times without considerable catalytic activity loss.

Nanoporous anodic Nb2O5 with pore-in-pore structure formation and its application for the photoreduction of Cr(VI)

An anodic film with a nanoporous structure was formed by anodizing niobium at 60 V in fluorinated ethylene glycol (fluoride-EG). After 30 min of anodization, the anodic film exhibited a "pore-in-pore" structure; that is, there were smaller pores growing inside larger pores. The as-anodized film was weakly crystalline and became orthorhombic Nb₂O₅ after heat treatment. The energy band gap of the annealed nanoporous Nb₂O₅ film was 2.9 eV. A photocatalytic reduction experiment was performed on Cr(VI) under ultraviolet (UV) radiation by immersing the nanoporous Nb₂O₅ photocatalyst in a Cr(VI) solution at pH 2. The reduction process was observed to be very slow; hence, ethylenediaminetetraacetic acid (EDTA) was added as an organic hole scavenger, which resulted in 100% reduction after 45 min of irradiation. The photocatalytic reduction experiment was also performed under visible light, and findings showed that complete reduction achieved after 120 min of visible light exposure.

Photocatalysis for Heavy Metal Treatment: A Review

Environmental and human health are threatened by anthropogenic heavy metal discharge into watersheds. Traditional processes have many limitations, such as low efficiency, high cost, and by-products. Photocatalysis, an emerging advanced catalytic oxidation technology, uses light energy as the only source of energy. It is a clean new technology that can be widely used in the treatment of organic pollutants in water. Given the excellent adaptability of photocatalysis in environmental remediation, it can be used for the treatment of heavy metals. In this comprehensive review, the existing reported works in relevant areas are summarized and discussed. Moreover, recommendations for future work are provided.

Quarry Residue: Treatment of Industrial Effluent Containing Dye

This work is devoted to the investigation of the discoloration of the synthetic and industrial effluent, using a quarry residue (MbP), which is a material naturally composed of mixed oxides, compared to zinc oxide (ZnO), acting as photocatalysts and adsorbents. The optimization of the pH and catalyst concentration parameters was carried out, and the industrial effluent was then treated by photocatalytic reactions, adsorption, and photolysis. Industrial effluent was supplied by a packaging company and was collected for a period of seven consecutive days, showing the oscillation of the parameters in the process. The material characterizations were obtained by scanning electron microscopy (SEM-EDS), X-Ray diffraction (XRD), and photoacoustic spectroscopy (PAS). The results indicated that the composition of the quarry waste is mainly silica and has Egap 2.16 eV. The quarry residue as photocatalyst was active for the artificial effluent (synthetic dye solution), with a maximum of 98% discoloration, and as an adsorbent for industrial effluent, with a maximum of 57% of discoloration. Although the quarry residue has shown results lower than ZnO, it is considered a promising material in adsorption processes and photocatalytic reactions for discoloration of aqueous solutions.

Continuous process applied to degradation of triclosan and 2.8-dichlorodibenzene-p-dioxin

This study describes the use of a prototype for the continuous photocatalytic reaction process using Fe/Nb₂O₅-immobilized catalyst for triclosan and 2.8-dichlorodibenzene-p-dioxin (2.8-DCDD)'s degradation. The experiments were carried out with different parameters and matrices in a steady state. In addition, photolysis and photocatalytic tests were performed. The results indicated that the generation of 2.8-DCDD was observed in matrices with Cl^-. The Fe/Nb₂O₅-immobilized catalysts were efficient in the degradation of triclosan and 2.8-dichlorodibenzene-p-dioxin. However, 2.8-DCDD formation was not observed in the ultra-pure water matrix, which indicated influence of ions. The photocatalysis was more efficient than the photolysis when comparing both matrices and radiation. Even with a radiation oscillation, the solar process showed positive results.

Nb2O5-Based Photocatalysts

Photocatalysis is one potential solution to the energy and environmental crisis and greatly relies on the development of the catalysts. Niobium pentoxide (Nb2O5), a typically nontoxic metal oxide, is eco-friendly and exhibits strong oxidation ability, and has attracted considerable attention from researchers. Furthermore, unique Lewis acid sites (LASs) and Brønsted acid sites (BASs) are observed on Nb2O5 prepared by different methods. Herein, the recent advances in the synthesis and application of Nb2O5-based photocatalysts, including the pure Nb2O5, doped Nb2O5, metal species supported on Nb2O5, and other composited Nb2O5 catalysts, are summarized. An overview is provided for the role of size and crystalline phase, unsaturated Nb sites and oxygen vacancies, LASs and BASs, dopants and surface metal species, and heterojunction structure on the Nb2O5-based catalysts in photocatalysis. Finally, the challenges are also presented, which are possibly overcome by integrating the synthetic methodology, developing novel photoelectric characterization techniques, and a profound understanding of the local structure of Nb2O5.

Mechanisms of enhanced hexavalent chromium removal from groundwater by sodium carboxymethyl cellulose stabilized zerovalent iron nanoparticles

Chromium (Cr) contamination poses serious threats to the environment and human health. Thus, batch and column experiments were performed to investigate hexavalent chromium [Cr (VI)] removal from solution and porous media using nanoscale zerovalent iron nanoparticles (NZVI) stabilized by sodium carboxymethyl cellulose (CMC). Batch experiments indicated that the mass ratio of Fe/CMC = 1, the presence of 150-200 mg L^-1 CMC and lower ionic strength led to optimum Cr (VI) removal in aqueous solution. Column experiments demonstrated that Cr (VI) removal was enhanced with decreasing solution pH and increasing CMC-NZVI concentration. The presence of CMC can increase Cr (VI) removal by NZVI in both aqueous solution and porous media by complexation precipitation of Cr (VI) compounds and better dispersion of NZVI. X-ray photoelectron spectroscopy (XPS) analysis revealed that an appropriate amount of CMC supported the redox reaction of Cr (VI) and NZVI. The removal of Cr (VI) through columns was 20.8% and 88.5% under no additional CMC and optimized CMC content, respectively. However, Cr (VI) removal decreased to 64.6% under excessive CMC content. The CMC modified NZVI nanoparticles were characterized by XRD, XPS and TEM techniques. These findings imply that CMC can be used as an effective stabilizer on NZVI which can in turn be applied for the efficient removal of Cr (VI) from industrial wastewater and groundwater.