Comparative overview of advanced oxidation processes and biological approaches for the removal pharmaceuticals

Microplastics removal in wastewater treatment plants: A review of the different approaches to limit their release in the environment

In last 10 years, the interest about the presence of microplastics (MPs) in the environment has strongly grown. Wastewaters function as a carrier for MPs contamination from source to the aquatic environment, so the knowledge of the fate of this emerging contaminant in wastewater treatment plants (WWTPs) is a priority. This work aims to review the presence of MPs in the influent wastewater (WW) and the effectiveness of the treatments of conventional WWTPs. Moreover, the negative impacts of MPs on the management of the processes have been also discussed. The work also focuses on the possible approaches to tackle MPs contamination enhancing the effectiveness of the WWTPs. Based on literature results, despite WWTPs are not designed for MPs removal from WW, they can effectively remove the MPs (up to 99 % in some references). Nevertheless, they normally act as "hotspots" of MPs contamination considering the remaining concentration of MPs in WWTPs' effluents can be several orders of magnitude higher than receiving waters. Moreover, MPs removed from WW are concentrated in sewage sludge (potentially >65 % of MPs entering the WWTP) posing a concern in case of the potential reuse as a soil improver. This work aims to present a paradigm shift intending WWTPs as key barriers for environmental protection. Approaches for increasing effectiveness against MPs have been discussed in order to define the optimal point(s) of the WWTP in which these technologies should be located. The need of a future legislation about MPs in water and sludge is discussed.

Photocatalytic Degradation of Naproxen: Intermediates and Total Reaction Mechanism

Photochemical and photocatalytic oxidation of naproxen (NPX) with UV-A light and commercial TiO2 under constant flow of oxygen have been investigated. Adsorption experiments indicated that 90% of the solute remained in the solution. Combined chemical analysis of samples on the photochemical degradation indicated that NPX in an aqueous solution (20 ppm) is efficiently transformed into other species but only 18% of the reactant is mineralized into CO2 and water after three hours of reaction. Performing the photocatalytic oxidation in the presence of TiO2, more than 80% of the organic compounds are mineralized by reactive oxidation species (ROS) within four hours of reaction. Analysis of reaction mixtures by a combination of analytical techniques indicated that naproxen is transformed into several aromatic naphthalene derivatives. These latter compounds are eventually transformed into polyhydroxylated aromatic compounds that are strongly adsorbed onto the TiO2 surface and are quickly oxidized into low-molecular-weight acids by an electron transfer mechanism. Based on this and previous studies on NPX photocatalytic oxidation, a unified and complete degradation mechanism is presented.

Sphere-shaped ZnO photocatalyst synthesis for enhanced degradation of the Quinolone antibiotic, Ofloxacin, under UV irradiation

The sphere-shaped zinc oxide (ZnO) photocatalyst was synthesized by the homogeneous precipitation method, using Zn(CH3COO)2·2H2O as a zinc precursor and NH4OH as a precipitating agent. The morphology and crystal structure of the prepared ZnO sample were studied by XRD, SEM, FT-IR, XPS, zeta potential measurements, and a low-temperature nitrogen adsorption-desorption technique. The optical characteristics of ZnO were determined by UV - Vis diffuse reflectance spectroscopy. ZnO photocatalyst performance of up to 100% within 210 min was observed in the photodegradation of the ofloxacin antibiotic under ultraviolet (UV) irradiation. The effect of antibiotic concentration, heavy metal ions, and water sources on the photocatalytic activity of ZnO demonstrated both the potential of its application under different conditions, and a good adaptability of this photocatalyst. The photodegradation reaction correlated well with the first-order kinetics model, with a rate constant of 0.0173 min-1. The reusability of the photocatalyst was verified after three cycles of use. Admittedly, photogenerated electrons and holes played a key role in removal of the antibiotic. This work showed the suitability of prepared ZnO for antibiotic removal, and its potential use for environmental protection.

An insight into the role of experimental parameters in advanced oxidation process applied for pharmaceutical degradation

The advanced oxidation process (AOP) is an efficient method to treat recalcitrance pollutants such as pharmaceutical compounds. The essential physicochemical factors in AOP experiments significantly influence the efficiency, speed, cost, and safety of byproducts of the treatment process. In this review, we collected recent articles that investigated the elimination of pharmaceutical compounds by various AOP systems in a water medium, and then we provide an overview of AOP systems, the formation mechanisms of active radicals or reactive oxygen species (ROS), and their detection methods. Then, we discussed the role of the main physicochemical parameters (pH, chemical interference, temperature, catalyst, pollutant concentration, and oxidant concentration) in a critical way. We gained insight into the most frequent scenarios for the proper and improper physicochemical parameters for the degradation of pharmaceutical compounds. Also, we mentioned the main factors that restrict the application of AOP systems in a commercial way. We demonstrated that a proper adjustment of AOP experimental parameters resulted in promoting the treatment performance, decreasing the treatment cost and the treatment operation time, increasing the safeness of the system products, and improving the reaction stoichiometric efficiency. The outcomes of this review will be beneficial for future AOP applicants to improve the pharmaceutical compound treatment by providing a deeper understanding of the role of the parameters. In addition, the proper application of physicochemical parameters in AOP systems acts to track the sustainable development goals (SDGs).

Contaminants of emerging concern: Occurrence, analytical techniques, and removal with electrochemical advanced oxidation processes with special emphasis in Latin America

The occurrence of contaminants of emerging concern (CECs) in environmental systems is gradually more studied worldwide. However, in Latin America, the presence of contaminants of emerging concern, together with their environmental and toxicological impacts, has recently been gaining wide interest in the scientific community. This paper presents a critical review about the source, fate, and occurrence of distinct emerging contaminants reported during the last two decades in various countries of Latin America. In recent years, Brazil, Chile, and Colombia are the main countries that have conducted research on the presence of these pollutants in biological and aquatic compartments. Data gathered indicated that pharmaceuticals, pesticides, and personal care products are the most assessed CECs in Latin America, being the most common compounds the followings: atrazine, acenaphthene, caffeine, carbamazepine, ciprofloxacin, diclofenac, diuron, estrone, losartan, sulfamethoxazole, and trimethoprim. Most common analytical methodologies for identifying these compounds were HPLC and GC coupled with mass spectrometry with the potential to characterize and quantify complex substances in the environment at low concentrations. Most CECs' monitoring and detection were observed near to urban areas which confirm the out-of-date wastewater treatment plants and sanitization infrastructures limiting the removal of these pollutants. Therefore, the implementation of tertiary treatment should be required. In this tenor, this review also summarizes some studies of CECs removal using electrochemical advanced oxidation processes that showed satisfactory performance. Finally, challenges, recommendations, and future perspectives are discussed.

A new approach of simultaneous adsorption and regeneration of activated carbon to address the bottlenecks of pharmaceutical wastewater treatment

This study proposes a sustainable approach for hard-to-treat wastewater using sintered activated carbon (SAC) both as an adsorption filter and as an electrode, allowing its simultaneous electrochemical regeneration. SAC improves the activated carbon (AC) particle contact and thus the conductivity, while maintaining optimal liquid flow. The process removed 87 % of total organic carbon (TOC) from real high-load (initial TOC of 1625 mg/L) pharmaceutical wastewater (PWW), generated during the manufacturing of azithromycin, in 5 h, without external input of chemicals other than catalytic amounts of Fe(II). Kinetic modelling indicated that adsorption was the dominant process, while concomitant electrochemical degradation of complex organics first converted them to short-chain acids, followed by their full mineralization. In-situ electrochemical regeneration of SAC, taking place at the same time as the treatment, is a key feature of our process, enhancing its performance and ensuring its stable operation over time, while eliminating cleaning downtimes altogether. The energy consumption of this innovative process was remarkably low at 8.0×10-3 kWh gTOC-1. This study highlights the potential of SAC for treating hard-to-treat effluents by concurrent adsorption and mineralization of organics.

Analysis of scientific and technological trends in the incorporation of activated carbon in advanced oxidation processes-a bibliometric study

There is high interest in the development of water pollution remediation technologies. Advanced oxidation processes (AOPs) are a promising alternative for the degradation of organic compounds; however, these technologies have been limited mainly by high operating costs and, in some cases, by forming byproducts, which can be more hazardous than the original pollutants. Activated carbon (AC) is a porous material that can be combined with AOP systems in various ways, given its adsorbent and catalytic characteristics. In addition, AC is a flexible, adaptable, and low-cost material. This article presents a bibliometric analysis of AOPs incorporating CA in scientific research and patents; the Scopus database was used to obtain patents and Orbit Express for patents. The most investigated AOPs incorporating AC are photocatalysis processes, Fenton processes, persulfate-based AOP, electrochemical processes, and ozonation. However, it is the persulfate-based AOP that has seen the greatest growth in scientific publications in recent years; this great interest can be related to the synergy that the process has with AC, allowing the degradation of contaminants via radical and non-radical. According to the maturity analysis of scientific publications, photocatalysis, Fenton, electrochemistry, ozonation, and persulfate technologies are in a growth stage and will reach maturity in 2034, 2042, 2040, 2034, and 2035, respectively; these technologies coupled with AC are expected to generate a greater number of patents when they reach maturity.

Electrochemically enhanced iron oxide-modified carbon cathode toward improved heterogeneous electro-Fenton reaction for the degradation of norfloxacin

In this work, different iron-based cathode materials were prepared using two different approaches: a novel one-step approach, which involved the incorporation of iron oxide with Printex® L6 carbon/PTFE (PL6C/PTFE) on bare carbon felt (CF) and a two-step approach, where iron oxide is deposited onto CF previously modified with PL6C/PTFE. The results obtained from the physical characterization indicated that the presence of iron oxide homogeneously dispersed on the felt fibers with the CF 3-D network kept intact in the one-step approach; whereas the formation of iron oxide aggregates between the felt fibers for material obtained using the two-step approach. Among the iron oxide-based cathodes investigated, the iron-incorporated electrode exhibited the greatest efficiency in terms of the removal and mineralization of norfloxacin (NOR) under neutral pH (complete NOR removal in less than 30 min with around 50% mineralization after 90 min). The findings of this study show that the low cost and simple-to-prepare iron-modified carbon-based materials in HEF process led to the enhanced degradation of organic contaminants in aqueous solutions.

Advanced oxidation process (AOP) combined biological process for wastewater treatment: A review on advancements, feasibility and practicability of combined techniques

Complexity of wastewater is the most challenging phenomenon on successful degradation of pollutant via any wastewater treatment regime. Upon availability of numerous techniques, Advanced Oxidation Processes (AOP) is the most promising technique for treating industrial wastewater. Higher operating cost is the most promising factor that possess challenge for the industrial scale usage of the AOP process. Combination of biological process with AOP helps in achieving sustainable degradation of toxic pollutant in the wastewater. AOP result in complete or partial degradation of toxic emerging pollutants with the help of free radicals like hydroxyl, superoxide, hydroperoxyl and sulphate radicals. In addition to this the presence of bio-enzymes and microorganisms helps in sustainable degradation of pollutant in an economical and environmentally friendly strategy. In this review, a detailed discussion was conducted on various AOP, focusing on catalytic ozonation, electrochemical oxidation, Sono chemical and photocatalytic processes. With the need for sustainable solutions for wastewater treatment, the use of AOP in conjunction with biological process has innumerous opportunities for not only wastewater treatment but also the production of high value by-products. Further, the effect of AOP combined biological processes needs to be analyzed in real time for the different concentration of industrial wastewater and their benefits needs to be explored in future towards achieving SDGs.

A review on the lignocellulosic derived biochar-based catalyst in wastewater remediation: Advanced treatment technologies and machine learning tools

Wastewater disposal in the ecosystem affects aquatic and human life, which necessitates the removal of the contaminants. Eliminating wastewater contaminants using biochar produced through the thermal decomposition of lignocellulosic biomass (LCB) is sustainable. Due to its high specific surface area, porous structure, oxygen functional groups, and low cost, biochar has emerged as an alternate contender in catalysis. Various innovative advanced technologies were combined with biochar for effective wastewater treatment. This review examines the use of LCB for the synthesis of biochar along with its activation methods. It also elaborates on using advanced biochar-based technologies in wastewater treatment and the mechanism for forming oxidizing species. The research also highlights the use of machine learning in pollutant removal and identifies the obstacles of biochar-based catalysts in both real-time and cutting-edge technologies. Probable and restrictions for further exploration are discussed.

Pharmaceutically active compounds in aqueous environment: recent developments in their fate, occurrence and elimination for efficient water purification

The existence of pharmaceutically active compounds (PhACs) in the water is a major concern for environmentalists due to their deleterious effects on living organisms even at minuscule concentrations. This review focuses on PhACs such as analgesics and anti-inflammatory compounds, which are massively excreted in urine and account for the majority of pharmaceutical pollution. Furthermore, other PhACs such as anti-epileptics, beta-blockers and antibiotics are discussed because they also contribute significantly to pharmaceutical pollution in the aquatic environment. This review is divided into two parts. In the first part, different classes of PhACs and their fate in the wastewater environment are presented. In the second part, recent advances in the removal of PhACs by conventional wastewater treatment plants, including membrane bioreactors (MBRs), activated carbon adsorption and bench-scale studies concerning a broad range of advanced oxidation processes (AOPs) that render practical and appropriate strategies for the complete mineralization and degradation of pharmaceutical drugs, are reviewed. This review indicates that drugs like diclofenac, naproxen, paracetamol and aspirin are removed efficiently by conventional systems. Activated carbon adsorption is suitable for the removal of diclofenac and carbamazepine, whereas AOPs are leading water treatment strategies for the effective removal of reviewed PhACs.

Biological treatment of triclosan using a novel strain of Enterobacter cloacae and introducing naphthalene dioxygenase as an effective enzyme

In recent years, triclosan (TCS) has been widely used as an antibacterial agent in personal care products due to the spread of the Coronavirus. TSC is an emerging contaminant, and due to its stability and toxicity, it cannot be completely degraded through traditional wastewater treatment methods. In this study, a novel strain of Enterobacter cloacae was isolated and identified that can grow in high TCS concentrations. Also, we introduced naphthalene dioxygenase as an effective enzyme in TCS biodegradation, and its role during the removal process was investigated along with the laccase enzyme. The change of cell surface hydrophobicity during TCS removal revealed that a glycolipid biosurfactant called rhamnolipid was involved in TCS removal, leading to enhanced biodegradation of TCS. The independent variables, such as initial TCS concentration, pH, removal duration, and temperature, were optimized using the response surface method (RSM). As a result, the maximum TCS removal (97%) was detected at a pH value of 7 and a temperature of 32 °C after 9 days and 12 h of treatment. Gas chromatography-mass spectrometry (GC/MS) analysis showed five intermediate products and a newly proposed pathway for TCS degradation. Finally, the phytotoxicity experiment conducted on Cucumis sativus and Lens culinaris seeds demonstrated an increase in germination power and growth of stems and roots in comparison to untreated water. These results indicate that the final treated water was less toxic.

Recent advancements in the fabrication and photocatalytic applications of graphitic carbon nitride-tungsten oxide nanocomposites

The present review focuses on the widely used graphitic carbon nitride (g-C3N4)-tungsten oxide (WO3) nanocomposite in photocatalytic applications. These catalysts are widely employed due to their easy preparation, high physicochemical stability, nontoxicity, electron-rich properties, electronic band structure, chemical stability, low cost, earth-abundance, high surface area, and strong absorption capacity in the visible range. These sustainable properties make them predominantly attractive and unique from other photocatalysts. In addition, graphitic carbon nitride (g-C3N4) is synthesized from nitrogen-rich precursors; therefore, it is stable in strong acid solutions and has good thermal stability up to 600 °C. This review covers the historical background, crystalline phases, density-functional theory (DFT) study, synthesis method, 0-D, 1-D, 2-D, and 3-D materials, oxides/transition/nontransition metal-doped, characterization, and photocatalytic applications of WO3/g-C3N4. Enhancing the catalytic performance strategies such as composite formation, element-doping, heterojunction construction, and nanostructure design are also summarized. Finally, the future perspectives and challenges for WO3/g-C3N4 composite materials are discussed to motivate young researchers and scientists interested in developing environment-friendly and efficient catalysts.

PVP encapsulated MXene coated on PET surface (PMP)-based photocatalytic materials: A novel photo-responsive assembly for the removal of tetracycline

Tetracycline (TC) antibiotic that is effective against wide-range micro-organisms, thereby used to control bacterial infection. The partial metabolism of TC antibiotics in humans and animals leads to the contamination of TC in the environments like water bodies. Thus, requirements to treat/remove/degrade TC antibiotics from the water bodies to control environmental pollution. In this context, this study focuses on fabricating PVP-MXene-PET (PMP) based photo-responsive materials to degrade TC antibiotics from the water. Initially, MXene (Ti2CTx) was synthesized using a simple etching process from the MAX phase (Ti3AlC2). The synthesized MXene was encapsulated using PVP and cast onto the surface of PET to fabricate PMP-based photo-responsive materials. The rough surface and micron/nano-sized pores within the PMP-based photo-responsive materials might be improved the photo-degradation of TC antibiotics. The synthesized PMP-based photo-responsive materials were tested against the photo-degradation of TC antibiotics. The band gap value of the MXene and PMP-based photo-responsive materials was calculated to be ∼1.23 and 1.67 eV. Incorporating PVP within the MXene increased the band gap value, which might be beneficial for the photo-degradation of TC, as the minimum band gap value should be ∼1.23 eV or more for photocatalytic application. The highest photo-degradation of ∼83% was achieved using PMP-based photo-degradation at 0.1 mg/L of TC. Furthermore, ∼99.71% of photo-degradation of TC antibiotics was accomplished at pH ∼10. Therefore, the fabricated PMP-based photo-responsive materials might be next-generation devices/materials that efficiently degrade TC antibiotics from the water.

Assessment of the Presence of Transformation Products of Certain Pharmaceutical Products (Psychotropic Family) by Suspect and Non-Targeted HRMS Screening in Wastewater Treatment Plants

Aquatic environments are the final receptors of human emissions and are therefore contaminated by molecules, such as pharmaceuticals. After use, these compounds and their metabolites are discharged to wastewater treatment plants (WWTPs). During wastewater treatment, compounds may be eliminated or degraded into transformation products (TPs) or may be persistent. The aim of this study was to develop an analytical method based on high resolution mass spectrometry (HRMS) for the identification of six psychotropic drugs that are widely consumed in France and present in WWTPs, as well as their potential associated metabolites and TPs. Four out of six psychotropic drugs and between twenty-five and thirty-seven potential TPs were detected in wastewater, although this was based on full scan data. TPs not reported in the literature and specific to the study sites and therefore to the wastewater treatment processes were tentatively identified. For the selected drugs, most known and present TPs were identified, such as desmethylvenlafaxine or norcitalopram. Moreover, the short fragmentation study led rather to the identification of several TPs of carbamazepine as ubiquitous persistent TPs.

Viable remediation techniques to cleansing wastewaters comprising endocrine-disrupting compounds

Endocrine-disrupting chemicals (EDCs) have recently gained prominence as emerging pollutants due to their significant negative impacts on diverse living forms in ecosystems, including humans, by altering their endocrine systems. EDCs are a prominent category of emerging contaminants in various aquatic settings. Given the growing population and limited access to freshwater resources, their expulsion from aquatic systems is also a severe issue. EDC removal from wastewater depends on the physicochemical properties of the specific EDCs found in each wastewater type and various aquatic environments. Due to these components' chemical, physical, and physicochemical diversity, various approaches based on physical, biological, electrochemical, and chemical procedures have been developed to eliminate them. The objective of this review is to provide the comprehensive overview by selecting recent approaches that showed significant impact on the best available methods for removing EDCs from various aquatic matrices. It is suggested that adsorption by carbon-based materials or bioresources is effective at higher EDC concentrations. Electrochemical mechanization works, but it requires expensive electrodes, continual energy, and chemicals. Due to the lack of chemicals and hazardous byproducts, adsorption and biodegradation are considered environmentally friendly. When combined with synthetic biology and an AI system, biodegradation can efficiently remove EDCs and replace conventional water treatment technologies in the near future. Hybrid in-house methods may reduce EDCs best, depending on the EDC and resources.

Investigating the biodegradability of iodinated X-ray contrast media in simultaneous nitrification and denitrification system

The present study investigated the biodegradation of three iodinated X-ray contrast media (ICM), namely, iopamidol, iohexol, and iopromide, in simultaneous nitrification-denitrification (SND) system maintained in a sequencing batch reactor (SBR). The results showed that variable aeration patterns (anoxic-aerobic-anoxic) and micro-aerobic condition were most effective in the biotransformation of ICM while achieving organic carbon and nitrogen removal. The highest removal efficiencies of iopamidol, iohexol, and iopromide were 48.24%, 47.75%, and 57.46%, respectively, in micro-aerobic condition. Iopamidol was highly resistant to biodegradation and possessed the lowest K_bio value, followed by iohexol and iopromide, regardless of operating conditions. The removal of iopamidol and iopromide was affected by the inhibition of nitrifiers. The transformation products after hydroxylation, dehydrogenation, and deiodination of ICM were detected in the treated effluent. Due to the addition of ICM, the abundance of denitrifier genera Rhodobacter and Unclassified Comamonadaceae increased, and the abundance of class TM7-3 decreased. The presence of ICM affected the microbial dynamics, and the diversity of microbes in SND resulted in improving the biodegradability of the compounds.

The use of agro-waste-based adsorbents as sustainable, renewable, and low-cost alternatives for the removal of ibuprofen and carbamazepine from water

The occurrence of residual pharmaceuticals in the aquatic environment poses major toxicological impacts and adds to the increasing pressure on water resources. Many countries are already suffering from water scarcity, and with the burdening costs of water and wastewater treatment, the race towards innovative sustainable strategies for pharmaceutical remediation is ongoing. Out of the available treatment methods, adsorption proved to be a promising, environmentally friendly technique, particularly when efficient waste-based adsorbents are produced from agricultural residues, thus maximizing the value of wastes, minimizing production costs, and saving natural resources from depletion. Among the residual pharmaceuticals, ibuprofen and carbamazepine are heavily consumed and highly occurring in the environment. This paper aims to review the most recent literature on the application of agro-waste-based adsorbents as sustainable alternatives for the removal of ibuprofen and carbamazepine from contaminated waters. Highlights on the major mechanisms implicated in the adsorption of ibuprofen and carbamazepine are presented, and light is shed on multiple operational parameters that hold a key role in the adsorption process. This review also highlights the effects of different production parameters on adsorption efficiency and discusses many limitations currently encountered. Finally, an analysis is included to compare the efficiency of agro-waste-based adsorbents relative to other green and synthetic adsorbents.

Sonocrystallization of a novel ZIF/zeolite composite adsorbent with high chemical stability for removal of the pharmaceutical pollutant azithromycin from contaminated water

Water pollution management, reduction, and elimination are critical challenges of the current era that threaten millions of lives. By spreading the coronavirus in December 2019, the use of antibiotics, such as azithromycin increased. This drug was not metabolized, and entered the surface waters. ZIF-8/Zeolit composite was made by the sonochemical method. Furthermore, the effect of pH, the regeneration of adsorbents, kinetics, isotherms, and thermodynamics were attended. The adsorption capacity of zeolite, ZIF-8, and the composite ZIF-8/Zeolite were 22.37, 235.3, and 131 mg/g, respectively. The adsorbent reaches the equilibrium in 60 min, and at pH = 8. The adsorption process was spontaneous, endothermic associated with increased entropy. The results of the experiment were analyzed using Langmuir isotherms and pseudo-second order kinetic models with a R2 of 0.99, and successfully removing the composite by 85% in 10 cycles. It indicated that the maximum amount of drug could be removed with a small amount of composite.

Recent advances in the removal of emerging contaminants from water by novel molecularly imprinted materials in advanced oxidation processes-A review

Recently, there has been a global focus on effectively treating emerging contaminants (ECs) in water bodies. Advanced oxidation processes (AOPs) are the primary technology used for ECs removal. However, the low concentrations of ECs make it difficult to overcome the interference of background substances in complex water quality, which limits the practical application of AOPs. To address this limitation, many researchers are developing new catalysts with preferential adsorption. Molecular imprinting technology (MIT) combined with conventional catalysts has been found to effectively enhance the selectivity of catalysts for the targeted catalytic degradation of pollutants. This review presents a comprehensive summary of the progress made in research on molecularly imprinted polymers (MIPs) in the selective oxidation of ECs in water. The preparation methods, principles, and control points of novel MIP catalysts are discussed. Furthermore, the performance and mechanism of the catalysts in photocatalytic oxidation, electrocatalytic oxidation, and persulfate activation are analyzed with examples. The possible ecotoxicological risks of MIP catalysts are also discussed. Finally, the challenges and prospects of applying MIP catalysts in AOP are presented along with proposed solutions. This review provides a better understanding of using MIP catalysts in AOPs to target the degradation of ECs.

Recent advances in advanced oxidation processes (AOPs) for the treatment of nitro- and alkyl-phenolic compounds

The presence of phenolic compounds in the aquatic environment has posed severe risks due to their toxicity. Among the phenolic families, nitro- and alkyl-phenolic compounds have been categorized as precedence contaminants by the United States Environmental Protection Agency (US EPA). Therefore, efficient treatment methods for wastewater containing nitro- and alkyl-phenolic compounds are urgently needed. Due to the advantages of creating reactive species and generating efficient degradation of hazardous contaminants in wastewater, advanced oxidation processes (AOPs) are well-known in the field of treating toxic contaminants. In this review paper, the recent directions in AOPs, catalysts, mechanisms, and kinetics of AOPs are comprehensively reviewed. Furthermore, the conclusion summarizes the research findings, future prospects, and opportunities for this study. The main direction of AOPs lies on the optimization of catalyst and operating parameters, with industrial applications remain as the main challenge. This review article is expected to present a summary and in-depth understanding of AOPs development; and thus, inspiring scientists to accelerate the evolution of AOPs in industrial applications.

Recent advances in the biological treatment of wastewater rich in emerging pollutants produced by pharmaceutical industrial discharges

Pharmaceuticals and personal care products present potential risks to human health and the environment. In particular, wastewater treatment plants often detect emerging pollutants that disrupt biological treatment. The activated sludge process is a traditional biological method with a lower capital cost and limited operating requirements than more advanced treatment methods. In addition, the membrane bioreactor combines a membrane module and a bioreactor, widely used as an advanced method for treating pharmaceutical wastewater with good pollution performance. Indeed, the fouling of the membrane remains a major problem in this process. In addition, anaerobic membrane bioreactors can treat complex pharmaceutical waste while recovering energy and producing nutrient-rich wastewater for irrigation. Wastewater characterizations have shown that wastewater's high organic matter content facilitates the selection of low-cost, low-nutrient, low-surface-area, and effective anaerobic methods for drug degradation and reduces pollution. However, to improve the biological treatment, researchers have turned to hybrid processes in which all physical, chemical, and biological treatment methods are integrated to remove various emerging contaminants effectively. Hybrid systems can generate bioenergy, which helps reduce the operating costs of the pharmaceutical waste treatment system. To find the most effective treatment technique for our research, this work lists the different biological treatment techniques cited in the literature, such as activated sludge, membrane bioreactor, anaerobic treatment, and hybrid treatment, combining physicochemical and biological techniques.

Effect of Pharmaceutical Sludge Pre-Treatment with Fenton/Fenton-like Reagents on Toxicity and Anaerobic Digestion Efficiency

Sewage sludge is successfully used in anaerobic digestion (AD). Although AD is a well-known, universal and widely recognized technology, there are factors that limit its widespread use, such as the presence of substances that are resistant to biodegradation, inhibit the fermentation process or are toxic to anaerobic microorganisms. Sewage sludge generated by the pharmaceutical sector is one such substance. Pharmaceutical sewage sludge (PSS) is characterized by high concentrations of biocides, including antibiotics and other compounds that have a negative effect on the anaerobic environment. The aim of the present research was to determine the feasibility of applying Advanced Oxidation Processes (AOP) harnessing Fenton's (Fe²⁺/H₂O₂) and Fenton-like (Fe³⁺/H₂O₂) reaction to PSS pre-treatment prior to AD. The method was analyzed in terms of its impact on limiting PSS toxicity and improving methane fermentation. The use of AOP led to a significant reduction of PSS toxicity from 53.3 ± 5.1% to 35.7 ± 3.2%, which had a direct impact on the taxonomic structure of anaerobic bacteria, and thus influenced biogas production efficiency and methane content. Correlations were found between PSS toxicity and the presence of Archaea and biogas yields in the Fe²⁺/H₂O₂ group. CH₄ production ranged from 363.2 ± 11.9 cm³ CH₄/g VS in the control PSS to approximately 450 cm³/g VS. This was 445.7 ± 21.6 cm³ CH₄/g VS (1.5 g Fe²⁺/dm³ and 6.0 g H₂O₂/dm³) and 453.6 ± 22.4 cm³ CH₄/g VS (2.0 g Fe²⁺/dm³ and 8.0 g H₂O₂/dm³). The differences between these variants were not statistically significant. Therefore, due to the economical use of chemical reagents, the optimal tested dose was 1.5 g Fe²⁺/6.0 g H₂O₂. The use of a Fenton-like reagent (Fe³⁺/H₂O₂) resulted in lower AD efficiency (max. 393.7 ± 12.1 cm³ CH₄/g VS), and no strong linear relationships between the analyzed variables were found. It is, therefore, a more difficult method to estimate the final effects. Research has proven that AOP can be used to improve the efficiency of AD of PSS.

Literature Review: Evaluation of Drug Removal Techniques in Municipal and Hospital Wastewater

There are several techniques for the removal of pharmaceuticals (drugs) from wastewater; however, strengths and weaknesses have been observed in their elimination processes that limit their applicability. Therefore, we aimed to evaluate the best techniques for the removal of pharmaceuticals from municipal and hospital wastewater. For this, a non-experimental, descriptive, qualitative-quantitative design was used, corresponding to a systematic review without meta-analysis. Based on established inclusion and exclusion criteria, 31 open-access articles were selected from the Scopus, ProQuest, EBSCOhost, and ScienceDirect databases. The results showed that high concentrations of analgesics such as naproxen (1.37 mg/L) and antibiotics such as norfloxacin (0.561 mg/L) are frequently found in wastewater and that techniques such as reverse osmosis, ozonation, and activated sludge have the best removal efficiency, achieving values of 99%. It was concluded that reverse osmosis is one of the most efficient techniques for eliminating ofloxacin, sulfamethoxazole, carbamazepine, and diclofenac from municipal wastewater, with removal rates ranging from 96 to 99.9%, while for hospital wastewater the activated sludge technique proved to be efficient, eliminating analgesics and antibiotics in the range of 41-99%.

Current Progress in Natural Degradation and Enhanced Removal Techniques of Antibiotics in the Environment: A Review

Antibiotics are used extensively throughout the world and their presence in the environment has caused serious pollution. This review summarizes natural methods and enhanced technologies that have been developed for antibiotic degradation. In the natural environment, antibiotics can be degraded by photolysis, hydrolysis, and biodegradation, but the rate and extent of degradation are limited. Recently, developed enhanced techniques utilize biological, chemical, or physicochemical principles for antibiotic removal. These techniques include traditional biological methods, adsorption methods, membrane treatment, advanced oxidation processes (AOPs), constructed wetlands (CWs), microalgae treatment, and microbial electrochemical systems (such as microbial fuel cells, MFCs). These techniques have both advantages and disadvantages and, to overcome disadvantages associated with individual techniques, hybrid techniques have been developed and have shown significant potential for antibiotic removal. Hybrids include combinations of the electrochemical method with AOPs, CWs with MFCs, microalgal treatment with activated sludge, and AOPs with MFCs. Considering the complexity of antibiotic pollution and the characteristics of currently used removal technologies, it is apparent that hybrid methods are better choices for dealing with antibiotic contaminants.

Resource utilization of tannery sludge to prepare biochar as persulfate activators for highly efficient degradation of tetracycline

In this work, a low-cost carbon-based catalyst (TSBC) was prepared by the facile one-pot pyrolysis of tannery sludge (TS) and used to activate persulfate (PS) for tetracycline (TC) removal. The results showed that TSBC-500 exhibited optimal physicochemical properties and the best performance for PS activation to remove TC from drinking water. Approximately 99.1% of TC was removed in the TSBC-500/PS system, which was considerably higher than those in the TSBC-500 adsorption and pure PS systems. Radical quenching experiments indicated that •OH and SO₄•^- played major roles in the TC removal in the TSBC-500/PS system. In addition, transition metals, functional groups, and the high degree of carbon structural defects were beneficial for PS activation to degrade TC. This study not only newly contributes to high-value utilization of TS as a PS activator but also offers an efficient method for the removal of organic pollutants.

Degradation of refractory organic matter in the effluent from a semi-aerobic aged refuse biofilter-treated landfill leachate by a nano-Fe3O4 enhanced ozonation process

In this study, the transformation and degradation mechanisms of refractory organic matter in biologically treated leachate from a semi-aerobic aged refuse biofilter (SAARB) in a nano-Fe₃O₄ enhanced ozonation process (nFe₃O₄-O₃) were investigated in batch experiments. A continuous experiment then confirmed the effectiveness of the process for SAARB effluent treatment. In a batch experiment, the effects of influencing factors, including nFe₃O₄ dosage, O₃ dosage and initial pH on the treatment performance of nFe₃O₄-O₃ process, were comprehensively investigated. The results showed that when the nFe₃O₄ dosage = 6 g L^-1, O₃ dosage = 0.15 L minute^-1 and initial pH = 7, the total organic carbon, absorbance at 254 nm and colour number removal efficiencies were 40.58%, 62.55% and 89.80%, respectively. In addition, most of the humic- and fulvic-like substances in the SAARB effluent were removed, and the condensation degree, aromaticity and humification degree of the organics were substantially reduced. The morphology and elemental valence state analysis showed that the nFe₃O₄ in the process was relatively stable and could form an nFe₃O₄-organic complex. Therefore, the probability of organics reacting with hydroxyl radical increased and the oxidation efficiency was enhanced. In the continuous experiment, both the O₃ dosage and hydraulic retention time (HRT) were the key influencing factors. The treatment efficiency of the nFe₃O₄-O₃ process was enhanced at a higher O₃ dosage and longer HRT. The electrical energy consumption of the continuous nFe₃O₃-O₃ process was calculated to be 17.72 kW h m^-3 in SAARB effluent treatment. This study proved the feasibility of biologically treated landfill leachate treatment by the nFe₃O₃-O₃ process.

Al/Cu-PILC as a Photo-Fenton Catalyst: Paracetamol Mineralization

Pillared clays have shown to effectively catalyze the photo-Fenton process without the necessity of acidic conditions, which is a very attractive feature from the perspective of environmentally friendly processes, especially when high natural abundance of chemical elements are incorporated. In this work, the catalytic activity of Al/Cu interlayered pillared clays for the degradation and mineralization of paracetamol through a photo-Fenton-like process was investigated. Al/Cu-pillared clays were prepared by adding ane Al/Cu pillaring solution to a bentonite suspension. X-ray diffraction (XRD) confirmed the enlargement of the interlayer space of the clay provoked by the pillaring process and Al and Cu species in the prepared samples were verified by atomic absorption spectroscopy (AAS). The specific surface area of pure bentonite was 2-fold increased after the Al/Cu pillaring process. A synthetic paracetamol solution with an initial concentration of 100 ppm was prepared for the assessment of the activity of the prepared materials. Different catalyst concentrations were tested (0.2, 0.5, 0.75, and 1 g L^-1) and the complete removal of paracetamol was achieved in all cases, but the highest mineralization rate (69.8 mg total organic carbon (TOC) g_cat ^-1 h^-1) corresponds to the catalyst loading of 0.5 g L^-1. An ultraviolet-C (UVC) light source was employed, and no adjustment of the pH to acidic conditions was needed to achieve these results. Liquid chromatography coupled to mass spectroscopy (LC-MS) was employed to identify the reaction intermediates of paracetamol degradation. A proposed pathway for the oxidation of paracetamol molecule is presented. The effect of Cu content in the pillared clay and the stability and reusability of the catalyst were also assessed. The kinetic constants of paracetamol removal were 0.2318 and 0.0698 min^-1, under photo-Fenton and UV + H₂O₂ processes, respectively.

Soil and Water Management Factors That Affect Plant Uptake of Pharmaceuticals: A Case Study

Water and food security are of global concern. Improving knowledge on crops’ potential uptake of pharmaceutical compounds (PhCs) is necessary to guarantee consumer health and improve the public’s perception of reclaimed water reuse. This study aimed to determine how water management (bottom-up applied for being supplied by Subsurface Drip Irrigation) and the plant rhizosphere effect on the uptake of PhCs. Five PhCs were mixed: atenolol, carbamazepine, dicoflenac, ibuprofen and valsartan. A total of 5 treatments were considered: 3 concentrations of PhCs in agricultural volcanic soil: 0.1, 10 and 100 µg·L−1; 0.1 µg·L−1 in sterilized soil; and a blank with three plant replications at 30, 45, and 60 days after emerging. The maximum quantity of the added PhCs was 100 µg·kg soil−1. A variant of the QuEChERS method was followed to extract PhCs from samples. The limits of quantification were between 10 ng·L−1 and 100 ng·L−1 in extracts. No PhCs over the limits of detection were detected (0.06–0.6 µg·kg−1 of dry plant sample). Hence, the described water reuse methodology poses a negligible consumer risk, which contrasts with hydroponic systems in which this risk has been shown. The results are discussed in terms of the effects of irrigation system, water management and the soil-plant barrier.

Enhancing the visible-light photoactivity of silica-supported TiO2 for the photocatalytic treatment of pharmaceuticals in water

Catalyst samples based on SiO₂-supported TiO₂ were prepared with the incorporation of Ag (metal), S (nonmetal), and ZnO@S (semiconductor and nonmetal). The materials were evaluated regarding their morphological, optical, and crystalline properties as well as their photoactivity under visible and ultraviolet light toward the degradation rate of a model emerging pollutant, acetaminophen (ACT). All modified materials exhibited improved performance over the undoped catalyst. The Ag-doped catalyst achieved the largest degradation under visible radiation (about 30% in 120 min), whereas under ultraviolet irradiation, the ZnO@S-doped sample exhibited the best performance (about 62% in 120 min). A Doehlert design was carried out to evaluate the influence of pH and temperature on the photoactivity of Ag-TiO₂/SiO₂. In addition, the role of each reactive species in the photodegradation reaction was investigated by radical scavenger experiments, and the superoxide radical anion O₂^•- was shown to be the predominant reactive species. The stability of the Ag-TiO₂/SiO₂ material under ultraviolet and visible light was confirmed after five successive operation cycles, showing a reasonable (about 50%) loss of activity under visible irradiation and a slight improvement (about 13%) under UV light, as a result of the photo-reduction of Ag⁺. Lastly, the effect of the initial pollutant concentration showed that ACT degradation using Ag-TiO₂/SiO₂ follows the Langmuir-Hinshelwood kinetics, with intrinsic reaction rate k = 2.71 × 10^-4 mmol L^-1 min^-1 under visible-light radiation.

Kinetic study on degradation of micro-organics by different UV-based advanced oxidation processes in EfOM matrix

Effluent organic matter (EfOM) contains a large number of substances that are harmful to both the environment and human health. To avoid the negative effects of organic matter in EfOM, advanced treatment of organic matter is an urgent task. Four typical oxidants (H₂O₂, PS, PMS, NaClO) and UV-combined treatments were used to treat micro-contaminants in the presence or absence of EfOM, because the active radical species produced in these UV-AOPs are highly reactive with organic contaminants. However, the removal efficiency of trace contaminants was greatly affected by the presence of EfOM. The degradation kinetics of two representative micro-contaminants (benzoic acid (BA) and para chlorobenzoic acid (pCBA)) was significantly reduced in the presence of EfOM, compared to the degradation kinetics in its absence. Using the method of competitive kinetics, with BA, pCBA, and 1,4-dimethoxybenzene (DMOB) as probes, the radicals (HO^·, SO₄^-·, ClO^·) proved to be the key to reaction species in advanced oxidation processes. UV irradiation on EfOM was not primarily responsible for the degradation of micro-contaminants. The second-order rate constants of the EfOM with radicals were determined to be (5.027 ± 0.643) × 10² (SO₄^-·), (3.192 ± 0.153) × 10⁴ (HO^·), and 1.35 × 10⁶ (ClO^·) (mg C/L)^-1 s^-1. In addition, this study evaluated the production of three radicals based on the concept of R_ct, which can better analyze its reaction mechanism.

Emerging Pollutants in Wastewater, Advanced Oxidation Processes as an Alternative Treatment and Perspectives

Emerging pollutants are present in wastewaters treated by conventional processes. Due to water cycle interactions, these contaminants have been reported in groundwater, surface water, and drinking waters. Since conventional processes cannot guarantee their removal or biotransformation, it is necessary to study processes that comply with complete elimination. The current literature review was conducted to describe and provide an overview of the available information about the most significant groups of emerging pollutants that could potentially be found in the wastewater and the environment. In addition, it describes the main entry and distribution pathways of emerging contaminants into the environment through the water and wastewater cycle, as well as some of the potential effects they may cause to flora, fauna, and humans. Relevant information on the SARS-CoV-2 virus and its potential spread through wastewater is included. Furthermore, it also outlines some of the Advanced Oxidation Processes (AOPs) used for the total or partial emerging pollutants removal, emphasizing the reaction mechanisms and process parameters that need to be considered. As well, some biological processes that, although slow, are effective for the biotransformation of some emerging contaminants and can be used in combination with advanced oxidation processes.

Multi-heteroatom-doped carbocatalyst as peroxymonosulfate and peroxydisulfate activator for water purification: A critical review

Catalytic activation of peroxymonosulfate (PMS) and peroxydisulfate (PDS) (or collectively known as persulfate, PS) using carbocatalyst is increasingly gaining attention as a promising technology for sustainable recalcitrant pollutant removal in water. Single heteroatom doping using either N, S, B or P is widely used to enhance the performance of the carbocatalyst for PS activation. However, the performance enhancement from single heteroatom doping is limited by the type of heteroatom used. To further enhance the performance of the carbocatalyst beyond the limit of single heteroatom doping, multi-heteroatom doping can be conducted. This review aims to provide a state-of-the-art overview on the development of multi-heteroatom-doped carbocatalyst for PS activation. The potential synergistic and antagonistic interactions of various heteroatoms including N and B, N and S, N and P, and N and halogen for PS activation are evaluated. Thereafter, the preparation strategies to develop multi-heteroatom-doped carbocatalyst including one-step and multi-step preparation approaches along with the characterization techniques are discussed. Evidence and summary of the performance of multi-heteroatom-doped carbocatalyst for various recalcitrant pollutants removal via PS activation are also provided. Finally, the prospects of employing multi-heteroatom-doped carbocatalyst including the need to study the correlation between different heteroatom combination, surface moiety type, and amount of dopant with the PS activation mechanism, identifying the best heteroatom combination, improving the durability of the carbocatalyst, evaluating the feasibility for full-scale application, developing low-cost multi-heteroatom-doped carbocatalyst, and assessing the environmental impact are also briefly discussed.

The state of art on the prediction of efficiency and modeling of the processes of pollutants removal based on machine learning

During the last few years, important advances have been made in big data exploration, complex pattern recognition and prediction of complex variables. Machine learning (ML) algorithms can efficiently analyze voluminous data, identify complex patterns and extract conclusions. In chemical engineering, the application of machine learning approaches has become highly attractive due to the growing complexity of this field. Machine learning allows computers to solve problems by learning from large data sets and provides researchers with an excellent opportunity to enhance the quality of predictions for the output variables of a chemical process. Its performance has been increasingly exploited to overcome a wide range of challenges in chemistry and chemical engineering, including improving computational chemistry, planning materials synthesis and modeling pollutant removal processes. In this review, we introduce this discipline in terms of its accessible to chemistry and highlight studies that illustrate in-depth the exploitation of machine learning. The main aim of the review paper is to answer these questions by analyzing physicochemical processes that exploit machine learning in organic and inorganic pollutants removal. In general, the purpose of this review is both to provide a summary of research related to the removal of various contaminants performed by ML models and to present future research needs in ML for contaminant removal.

Prediction of degradability of micropollutants by sonolysis in water with QSPR - a case study on phenol derivates

The increasing quantity and variety of organic contaminants discharged into surface and groundwater increase the necessity of additional and suitable water treatment methods, which can be incorporated into existing wastewater treatment plants. The huge variety of micropollutants and local variability of the composition of the organic load or matrix effects paired with multiple possible degradation processes lead to the requirement of a recommendation tool for the best possible water treatment method under given local conditions. Due to the diversity of physicochemical properties of micropollutants, such predictions are challenging. In this study, a quantitative correlation between the structural properties of certain micropollutants and their degradability using high-frequency sonolysis has been investigated. Therefore, Quantitative Structure-Property Relationship (QSPR) has been applied on a set of phenol derivates. To obtain the kinetic data, all experiments have been conducted in standardized, constant conditions for all 32 investigated phenol derivates. QSPR modelling was then executed using the software PaDEL for descriptor calculation and the software QSARINS for the overall modelling process including genetic algorithm (GA) and multiple linear regression (MLR). The final model consisting of 5 molecular descriptors was selected using a multi-criteria decision-making method based on extensive statistical parameters. The predictive power and robustness of the model was evaluated by means of internal cross validation and external validation using an independent validation set. The final selected model showed very good values for regression abilities, predictive power as well as stability (R²_adj = 0.9455, CCC_tr = 0.9777, Q²_loo = 0.9285, CCC_ext = 0.9797 and Q²_ext-F1 = 0.9711). The applicability domain of the QSPR model was defined based on the Williams plot and Insubria plot. The five OECD principles for the application of QSPR/QSAR modelling in industry and regulation were fulfilled in the whole process to the best of our knowledge, including the collection of the underlying experimental data as well as the entire modelling process. The final QSPR model included the molecular polarity and occurrence of hydrogen bonds as major influences on the reaction rate constants in accordance with previous studies. Nevertheless, potential biases in the selection of these descriptors due to the small size of the dataset were highlighted.

Removal of anti-inflammatory drugs using activated carbon from agro-industrial origin: current advances in kinetics, isotherms, and thermodynamic studies

Nonsteroidal anti-inflammatory drugs (NSAIDs) are highly consumed around the world and consequently found as emerging pollutants in water; they are found in concentrations up to µg L−1 making their removal a priority. In this matter, adsorption is an efficient alternative for drug removal, so using activated carbon (AC) as an adsorbent is a highly explored subject. The current interest is to obtain AC from waste, for example, those of agro-industrial origin, reducing this way the overall costs of the process. Although information regarding the use of AC from agro-industrial origin in the removal of NSAIDs is limited, an exclusive compilation is required to understand the state of the art to date. This work aims to update information related to the adsorption of ibuprofen, diclofenac, and naproxen on agro-industrial AC, and it is focused on the period 2016–2021. It highlights the characteristics of agro-industrial AC responsible for efficient adsorption. Recent adsorption studies, including kinetics, isotherms, and thermodynamics, are analyzed and compared. Progress on removing NSAIDs from real wastewater is also presented and finally proposed adsorption mechanisms and costs related to these removal processes.

Assessment of effluents quality through ecotoxicological assays: evaluation of three wastewater treatment plants with different technologies

The water quality of the effluents is mainly focused on physicochemical and microbiological parameters. However, the ecotoxicological assessments are crucial to ensure an effective water quality of the effluents. This work aims to assess the ecotoxicity of effluents originated from WWTPs with different wastewater treatment technologies. For that, effluent samples from three WWTPs with different treatment processes were seasonally collected. Physicochemical parameters were determined, the toxicity towards daphnia, protozoan, and microalgae organisms was evaluated, and data correlated. Toxicity assays showed different susceptibility of the organisms to the effluents and that toxicity is dependent on the season and wastewater treatment technology. No toxicity was observed to daphnia in winter and spring, but ~100% of mortality was observed in effluent from WWTP A in summer. Growth inhibition was observed for both protozoan and microalgae for all effluents and in all seasons with highest values in spring in WWTP C (~80%) for the protozoan while the highest microalgae growth inhibition percentage was observed for WWTP B in both spring (~80%) and summer (~80%). These results show that effluents might have negative impacts into their receiving water systems and highlight that a global assessment of effluent quality should include ecotoxicological assays to complement physicochemical and microbiological data for an operative environmental management of wastewater treatment plants.

Enhanced degradation mechanism of tetracycline by MnO2 with the presence of organic acids

In this study, we constructed MnO₂/organic acid (OA) systems using MnO₂ colloid, the most reactive phase of Mn(IV), and two kinds of OA (oxalic acid and l-tartaric acid). We investigated the effect of OA on tetracycline (TC) degradation by MnO₂. The results show that both OA obviously accelerate TC degradation by MnO₂. Mn(III) formed during the reaction lead to the acceleration. Mn(III)-oxalate complex formed in oxalic acid system resulted in the lower degradation efficiency than that in l-tartaric acid system. The acceleration of oxalic acid was decreased when the concentration was more than 75 μM, and even completely disappeared with the concentration of 500 μM, owning to the fact that excess oxalic acid decreased the pH and some MnO₂ was fast reduced to Mn²⁺ by oxalic acid and unable to react with TC. The impact of pH on TC degradation resulted from the influences of H⁺ on MnO₂ redox potentials and TC deprotonation. And acidic conditions accelerated TC degradation. The addition of Mg²⁺, Ca²⁺, Fe³⁺ and Zn²⁺ exhibited an inhibitory effect in both systems for their occupying reactive sites on MnO₂ surface and blocking the access of TC to MnO₂. Similar intermediates in the two systems were detected, indicating a similar TC degradation mechanism including a series of reactions like dehydration, hydroxylation and oxidation. The MnO₂/OA system provides an efficient treatment of TC in wastewater. And it is also noticeable that MnO₂/OA system should also have an important effect on the fate of pollutants in environment, from our results.

Two-Dimensional Nanomaterials for the Removal of Pharmaceuticals from Wastewater: A Critical Review

The removal of pharmaceuticals from wastewater is critical due to their considerable risk on ecosystems and human health. Additionally, they are resistant to conventional chemical and biological remediation methods. Two-dimensional nanomaterials are a promising approach to face this challenge due to their combination of high surface areas, high electrical conductivities, and partially optical transparency. This review discusses the state-of-the-art concerning their use as adsorbents, oxidation catalysts or photocatalysts, and electrochemical catalysts for water treatment purposes. The bibliographic search bases upon academic databases including articles published until August 2021. Regarding adsorption, high removal capacities (>200 mg g−1) and short equilibrium times (<30 min) are reported for molybdenum disulfide, metal-organic frameworks, MXenes, and graphene oxide/magnetite nanocomposites, attributed to a strong adsorbate-adsorbent chemical interaction. Concerning photocatalysis, MXenes and carbon nitride heterostructures show enhanced charge carriers separation, favoring the generation of reactive oxygen species to degrade most pharmaceuticals. Peroxymonosulfate activation via pure or photo-assisted catalytic oxidation is promising to completely degrade many compounds in less than 30 min. Future work should be focused on the exploration of greener synthesis methods, regeneration, and recycling at the end-of-life of two-dimensional materials towards their successful large-scale production and application.

Recent Trends in Pharmaceuticals Removal from Water Using Electrochemical Oxidation Processes

Nowadays, the research on the environmental applications of electrochemistry to remove recalcitrant and priority pollutants and, in particular, drugs from the aqueous phase has increased dramatically. This literature review summarizes the applications of electrochemical oxidation in recent years to decompose pharmaceuticals that are often detected in environmental samples such as carbamazapine, sulfamethoxazole, tetracycline, diclofenac, ibuprofen, ceftazidime, ciprofloxacin, etc. Similar to most physicochemical processes, efficiency depends on many operating parameters, while the combination with either biological or other physicochemical methods seems particularly attractive. In addition, various strategies such as using three-dimensional electrodes or the electrosynthesis of hydrogen peroxide have been proposed to overcome the disadvantages of electrochemical oxidation. Finally, some guidelines are proposed for future research into the applications of environmental electrochemistry for the degradation of xenobiotic compounds and micropollutants from environmental matrices. The main goal of the present review paper is to facilitate future researchers to design their experiments concerning the electrochemical oxidation processes for the degradation of micropollutants/emerging contaminants, especially, some specific drugs considering, also, the existing limitations of each process.

MoS2-assisted Fe2+/peroxymonosulfate oxidation for the abatement of phenacetin: efficiency, mechanisms and toxicity evaluation

In this study, molybdenum disulfide (MoS₂) was chosen as a co-catalyst to enhance the removal efficiency of phenacetin (PNT) in water by a ferrous ion-activated peroxymonosulfate (Fe²⁺/PMS) process. Operating parameters, such as the initial solution pH and chemical dose on PNT degradation efficiency were investigated and optimized. Under an initial pH of 3, an Fe²⁺ dose of 25 μM, a PMS dose of 125 μM and a MoS₂ dose of 0.1 g L⁻¹, the degradation efficiency of PNT reached 94.3%, within 15 min. The presence of common water constituents including Cl⁻, HCO₃⁻, SO₄²⁻ and natural organic matter (NOM) will inhibit degradation of PNT in the MoS₂/Fe²⁺/PMS system. Radical quenching tests combined with electron paramagnetic resonance (EPR) results indicated that in addition to free radical species (˙OH, SO₄˙⁻ and O₂˙⁻), nonradical reactive species (¹O₂) were also crucial for PNT degradation. The variations in the composition and crystalline structure of the MoS₂ before and after the reaction were characterized by XPS and XRD. Further, the degradation pathways of PNT were proposed according to the combined results of LC/TOF/MS and DFT calculations, and primarily included hydroxylation of the aromatic ring, cleavage of the C–N bond of the acetyl-amino group, and cleavage of the C–O bond of the ethoxy group. Finally, toxicity assessment of PNT and its products was predicted using the ECOSAR program.

Performance, mechanisms and toxicity evaluation of PNT degradation by the MoS₂/Fe²⁺/PMS system were investigated.