TiO2/g-C3N4 photocatalyst for the purification of potassium butyl xanthate in mineral processing wastewater

Enhanced visible light photocatalytic performance of carbon and oxygen co-doped carbon nitride with a three-dimensional structure: Performance and mechanism study

As a cost-effective photocatalyst, carbon nitride (g-C3N4) holds tremendous promise for addressing energy shortages and environmental pollution. However, its application is limited by disadvantages such as low specific surface area and easy recombination of photogenerated electron-hole pairs. This study introduces C and O co-doped g-C3N4 with a three-dimensional (3D) structure achieved through a straightforward one-step calcination process, demonstrating excellent photocatalytic activity of hydrogen production and oxytetracycline degradation, with superoxide radicals as the primary active species. We propose a plausible enhanced mechanism based on systematic characterizations and density functional theory calculations. The 3D structure confers a substantial specific surface area, enhancing both the adsorption area and active sites of catalysts while bolstering structural stability. Co-doping optimizes the band structure and electric conductivity of the catalyst, facilitating rapid migration of photogenerated charges. The synergistic effects of these enhancements significantly elevate the photocatalytic performance. This study presents a convenient and feasible method for the preparation of dual-regulated photocatalysts with outstanding performance.

Micro-Spherical BiOI Photocatalysts for Efficient Degradation of Residual Xanthate and Gaseous Nitric Oxide

BiOI microspheres were synthesized using the solvothermal method for the degradation of residual xanthate and gaseous nitric oxide (NO) under visible light irradiation. The as-prepared BiOI nanomaterials were then characterized using various technologies, including XRD, FE-SEM, TEM, UV-Vis DRS, and XPS. The photodegradation results show that the removal efficiency of isobutyl sodium xanthate can reach 98.08% at an initial xanthate concentration of 120 mg/L; that of NO is as high as 96.36% at an inlet NO concentration of 11 ppm. Moreover, the effects of operational parameters such as catalyst dosage, initial xanthate concentration, and pH value of wastewater on the removal of xanthate were investigated. The results of scavenging tests and full-spectrum scanning indicate that ·O2- radicals are the main active species in xanthate degradation, and peroxide xanthate is an intermediate. The reusability of BiOI was explored through cyclic experiments. Furthermore, the reaction path and the mechanism of NO removal using BiOI were analyzed, and the main active species was also ·O2-. It is concluded that BiOI photocatalysts have high potential for wastewater treatment and waste gas clean-up in the mineral industry.

Charge transfer mechanism through S-scheme heterojunction in in-situ synthesized TiO2/Fe-doped hydroxyapatite for improved photodegradation of xanthate

The heterojunction structure of the photocatalyst composite, which necessitates a robust interface and sufficient contact areas, holds the key to obtaining high charge carrier migration efficiency. Here, a novel composite, TiO2 nanoparticles/Fe-doped hydroxyapatite (TONPs/FH_CS), is fabricated using a two-step synthetic technique, in which FH_CS is synthesized from artificial converter slag enriched with Fe and Ca. The unique nanorod@plate structure of FH_CS enables the uniform immobilization of TONPs onto FH_CS. Thereby, an n-n type heterojunction exhibits a highly intimate Ti-O-Fe heterointerface. Kelvin probe testing demonstrates the formation of an interfacial electric field oriented from FH_CS to TONPs, which serves as the driving force for interfacial electron transfer through the Ti-O-Fe channels. The photoacoustic signals provide information on electron trap levels and densities, indicating the formation of the electron transfer channels. •O2- and •OH species are responsible for being the active species in this system. A photoexcited carrier transfer pathway exhibiting an S-scheme mechanism with high separation efficiency significantly enhances the utilization of charge carriers in each phase. Thus, improved xanthate degradation has been achieved using a heterojunction containing a photocatalyst derived from industrial solid waste. This work demonstrates the significant potential of steel-making byproduct utilization in industrial wastewater treatment.

Degradation of sulfamethoxazole and antibiotic resistance genes from surface water in the photocatalyst-loading bionic ecosystems

The behavior and removal of sulfamethoxazole (SMX) and 3 typical corresponding antibiotic resistance genes (ARGs) including sul1, sul2, sul3, and 16S rDNA in surface water were investigated in the photocatalyst-loading bionic ecosystems (PCBEs). Synthesized composite photocatalyst g-C3N4/TiO2 showing higher catalytic activity than Fe/g-C3N4/TiO2 was selected in the PCBEs. Five PCBEs, i.e., A-the control (without bionic grass or photocatalyst), B-bionic grass loaded with 4.12 g/m2 g-C3N4/TiO2, C-bionic grass loaded with 8.25 g/m2 g-C3N4/TiO2, D-bionic grass loaded with 12.37 g/m2 g-C3N4/TiO2, and E-bionic grass loaded with 16.5 g/m2 g-C3N4/TiO2 were constructed and operated in a medium-scale running cyclical flume. SMX could be photolyzed efficiently by g-C3N4/TiO2 with an optimal unit load on the bionic grass of 12.37 g/m2. 3-amino-5-methylisooxazole and p-aminobenzene sulfonamide were selected as main intermediates through the analyses of SMX degradation mechanisms and pathways, and detected in the aqueous phase and bionic grass. The intermediates were higher in the underwater part of the bionic grass than the above-water part. The overall removal of SMX ranged from 31.7 % to 82.3 % in 5 PCBEs, and the removal of sul1and sul2 were 0.2 %- 62.9 % in the aqueous phase and 8.4 %-63.2 % in the sediment. PCBE D might be the best construction when SMX and ARGs' removal was considered comprehensively. Moreover, the microbial structures showed Proteobacteria as the most dominant bacterial species had a relative abundance of 22.2 %-26.6 % and 33.4 %-68.2 % in the aquatic phase and sediment respectively, illustrating that the removal of the antibiotic and ARGs was bound up with the variations of dominant bacteria in the ecosystems. The findings illustrated that ecosystems with bionic grass and photocatalysts could be a promising technology for the removal of typical antibiotics and ARGs from surface water.

An environmentally friendly approach for industrial wastewater treatment and bio-adsorption of heavy metals using Pistacia soft shell (PSS) through flocculation-adsorption process

In this research, the potential application of Pistacia soft shell (PSS) was investigated as a novel bio-based flocculant for pulp and paper wastewater (PPWW) treatment. In line with this, after characterization of the PSS, the removal efficiencies of chemical oxygen demand (COD), turbidity and heavy metals (Cu2+ and Pb2+) from PPWW were investigated with different dosage of PSS. The results were compared with alum as a reference flocculant. In addition, the effect of pH adjustment on the flocculation-adsorption performance of PSS was studied under acidic and alkaline condition. Zeta potential, BET, FTIR and SEM as well as kinetics and isotherm analyses were conducted for mechanistic understanding. According to the results, PSS treatment could remove COD, turbidity, Cu2+ and Pb2+ up to 67%, 87%, 70% and 74%, respectively which were better than alum: 56%, 85%, 31% and 35%. It was observed that, pH adjustment significantly improved the performance of PSS treatment. Maximum removal efficiencies of 92%, 95%, 97% and 98% were achieved for COD, turbidity, Cu2+ and Pb2+, respectively, under optimal condition of using 2 g/L PSS at pH 9. The mechanism analysis revealed that the high removal efficiency of PSS is related to the dual flocculation-adsorption of bridging and sweeping mechanisms. The results of this study suggested PSS as a promising, sustainable and eco-friendly bio-based flocculant and adsorbent for industrial wastewater treatment.

Hydrothermal preparation of NiO/La-NaTaO3 composite photocatalyst for degradation of ammonium dibutyl dithiophosphate wastewater

The discharge of a large amount of flotation reagents wastewater can cause significant environmental pollution. In this study, NiO/La-NaTaO3 nano-photocatalyst was prepared and applied to degrade synthetic flotation reagent ammonium dibutyl dithiophosphate wastewater. Various characterization results confirmed the successful synthesis of NiO/La-NaTaO3, and UV-vis DRS analysis revealed a band gap of 3.96 eV for 4 wt% NiO/2.5% La-NaTaO3. Under UV light, the degradation rate of 20 mg 4 wt% NiO/2.5% La-NaTaO3 photocatalyst reached its optimum within 4.5 h at pH=3, exhibiting a 1.45 times improvement compared to pure NaTaO3. Radical trapping experiments and EPR results showed that ·OH and·O2- showed major contribution to the degradation. Furthermore, photocatalytic mechanisms and toxicity evolution were investigated, demonstrating the potential application of photocatalytic methods for treating flotation reagent wastewater.

Preparation of TiO2/Fe-MOF n‒n heterojunction photocatalysts for visible-light degradation of tetracycline hydrochloride

Visible-light-assisted photocatalysis has been recognized as an effective solution to the degradation of various pollutants including antibiotics, pesticides, herbicides, microplastics, and organic dyes. Herein, an n-n heterojunction TiO₂/Fe-MOF photocatalyst is reported, designed via hydrothermal synthesis route. TiO₂/Fe-MOF photocatalyst was characterized by XPS, BET, EIS, EDS, DRS, PL, FTIR, XRD, TEM, SEM and HRTEM techniques. Inspired by XRD, FTIR, XPS, EDS, TEM, SEM, and HRTEM analyses, the successful synthesis of n-n heterojunction TiO₂/Fe-MOF photocatalysts was proved. The migration efficiency of the light-induced electron-hole pairs was confirmed by the PL and EIS tests. TiO₂/Fe-MOF exhibited a significant performance for tetracycline hydrochloride (TC) removal under visible light irradiation. TC removal efficiency for TiO₂/Fe-MOF (15%) nanocomposite reached 97% within 240 min, ca. 11 times higher than pure TiO₂. The photocatalytic enhancement of TiO₂/Fe-MOF could be attributed to the broadening the light response range, forming an n-n junction between Fe-MOF and TiO₂ components, suppressing charge recombination. Based on recycling experiments, TiO₂/Fe-MOF had a good potential to be used in consecutive TC degradation tests.

One-step chemically vapor deposited hybrid 1T-MoS2/2H-MoS2 heterostructures towards methylene blue photodegradation

The photocatalytic degradation of methylene blue is a straightforward and cost-effective solution for water decontamination. Although many materials have been reported so far for this purpose, the proposed solutions inflicted high fabrication costs and low efficiencies. Here, we report on the synthesis of tetragonal (1T) and hexagonal (2H) mixed molybdenum disulfide (MoS2) heterostructures for an improved photocatalytic degradation efficiency by means of a single-step chemical vapor deposition (CVD) technique. We demonstrate that the 1T-MoS2/2H-MoS2 heterostructures exhibited a narrow bandgap ∼ 1.7 eV, and a very low reflectance (<5%) under visible-light, owing to their particular vertical micro-flower-like structure. We exfoliated the CVD-synthesised 1T-MoS2/2H-MoS2 films to assess their photodegradation properties towards the standard methylene blue dye. Our results showed that the photo-degradation rate-constant of the 1T-MoS2/2H-MoS2 heterostructures is much greater under UV excitation (i.e., 12.5 × 10-3 min-1) than under visible light illumination (i.e., 9.2 × 10-3 min-1). Our findings suggested that the intermixing of the conductive 1T-MoS2 with the semi-conducting 2H-MoS2 phases favors the photogeneration of electron-hole pairs. More importantly, it promotes a higher efficient charge transfer, which accelerates the methylene blue photodegradation process.

Membrane reactor for production of biodiesel from nonedible seed oil of Trachyspermum ammi using heterogenous green nanocatalyst of manganese oxide

Conventional homogeneous-based catalyzed transesterification for the production of biodiesel can be replaced with a membrane reactor that has an immobilized heterogeneous catalyst. Combining reaction with separation while utilizing membranes with a certain pore size might boost conversion process. this investigation to study the effectiveness of membrane reactor in combination with heterogeneous green nano catalysis of MnO2. Techniques such as XRD, EDX, FTIR, SEM, and TGA were used to characterize the synthesized MnO2 nano catalyst. The highest conversion of around 94% Trachyspermum ammi oil was obtained by MnO2. The optimum process variables for maximum conversion were catalyst loading of 0.26 (wt.%), 8:1 M ratio, 90 °C reaction temperature, and time 120 min. The green nano catalyst of MnO2 was reusable up to five cycles with minimum loss in conversion rate of about 75% in the fifth cycle. Nuclear magnetic resonance validated the synthesis of methyl esters. It was concluded that membrane reactor a promising technique to efficiently transesterify triglycerides into methyl esters and enable process intensification uses MnO2 as a catalyst.

Synthesis, characterization and adsorption behavior of modified cellulose nanocrystals towards different cationic dyes

Green and efficient removal of polluted materials are essential for the sustainability of a clean and green environment. Nanomaterials, particularly cellulose nanocrystals (CNCs), are abundant in nature and can be extracted from various sources, including cotton, rice, wheat, and plants. CNCs are renewable biomass materials with a high concentration of polar functional groups. This study used succinic anhydride to modify the surface of native cellulose nanocrystals (NCNCs). Succinic anhydride has been frequently used in adhesives and sealant chemicals for a long time, and here, it is evaluated for dye removal performance. The morphology and modification of CNCs studied using FTIR, TGA & DTG, XRD, SEM, AFM, and TEM. The ability of modified cellulose nanocrystals (MCNCs) to adsorb cationic golden yellow dye and methylene blue dye was investigated. The MCNCs exhibited high adsorption affinity for the two different cationic dyes. The maximum adsorption efficiency of NCNCs and MCNCs towards the cationic dye was 0.009 and 0.156 wt%. The investigation for adhesive properties is based on the strength and toughness of MCNCs. MCNCs demonstrated improved tensile strength (2350 MPa) and modulus (13.9 MPa) using E-51 epoxy system and a curing agent compared to 3 wt% composites. This research lays the groundwork for environmentally friendly fabrication and consumption in the industrial sector.

Facile synthesis and comparative study of the enhanced photocatalytic degradation of two selected dyes by TiO2-g-C3N4 composite

Photocatalysis is considered a useful technique employed for the dye degradation through solar light, visible or UV light irradiation. In this study, TiO₂, g-C₃N₄, and TiO₂-g-C₃N₄ nanocomposites were successfully synthesized and studied for their ability to degrade Rhodamine B (RhB) and Reactive Orange 16 (RO-16), when exposed to visible light. The analytical techniques including XRD, TEM, SEM, DRS, BET, XPS, and fluorescence spectroscopy were used to explore the characteristics of all the prepared semiconductors. The photocatalytic performance of synthesized materials has been tested against both the selected dyes, and various experimental parameters were studied. The experimental results demonstrate that, in comparison to other fabricated composites, the TiO₂-g-C₃N₄ composite with the optimal weight ratio of g-C₃N₄ (15 wt%) to TiO₂ has shown outstanding degrading efficiency against RhB (89.62%) and RO-16 (97.20%). The degradation experiments were carried out at optimal conditions such as a catalyst load of 0.07 g, a dye concentration of 50 ppm, and a temperature of 50 ℃ at neutral pH in 90 min. In comparison to pure TiO₂ and g-C₃N₄, the TiO₂-g-C₃N₄, a semiconductor, has shown higher degradation efficiency due to its large surface area and decreased electron-hole recombination. The scavenger study gave an idea about the primary active species (^-OH radicals), responsible for dye degradation. The reusability of TiO₂-g-C₃N₄ was also examined in order to assess the composite sustainability.

The novel strategy of designing perovskite fiber membrane as reactor for catalytic oxidation

Negative impacts of wastewater contamination include harm to the environment, people, plants, and animals. Metal-based heterogeneous catalysts, particularly transition metal oxide catalysts, are a therapeutic option. However, they have limited reusability and cause secondary contaminations through metal leaching. In this work, a new membrane catalyst made of perovskite-type fiber was created and tested to remove methylene blue from wastewater. These innovative 3D perovskite ceramic catalysts work well in the breakdown of pollutants and dramatically lessen possible secondary contaminations caused by metal leaching from catalysts.

Synthesis and Application of Catalytic Materials in Energy and Environment

Catalytic materials have become prominent in many high-tech fields in recent years [...]

Design of TiO2/Ag3BiO3 n-n heterojunction for enhanced degradation of tetracycline hydrochloride under visible-light irradiation

Pharmaceutical residual contaminants in aquatic ecosystems have caused severe risks to human health. Affordable, eco-friendly and effective photocatalysts to deal with these pollutants has become a hot topic in the scientific community. In this research, Ag₃BiO₃ nanoparticles were embedded on TiO₂ to form n-n heterojunction through a facile hydrothermal method. According to scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR), brunauer emmett teller (BET), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDS), photoluminescence (PL), X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectroscopy (UV-vis DRS) tests, the successful construction of TiO₂/Ag₃BiO₃ heterojunction is proved. TiO₂/Ag₃BiO₃ heterojunctions were employed as photocatalysts to remove tetracycline hydrochloride (TCH) under visible light irradiation in aqueous solution. Optimum TCH photodegradation efficiency was observed for TiO₂/Ag₃BiO₃ (10%), 15.4 times superior to that of TiO₂. The enhanced TCH photodegradation efficiency of TiO₂/Ag₃BiO₃ results from improved light absorption capacity and the reduction of recombination of photogenerated charge carriers via generation of n-n heterojunctions. The mechanism of increasing the photodegradation efficiency of TCH was determined by employing reactive species quenching experiments. TiO₂/Ag₃BiO₃ (10%) also exhibited an acceptable stability.

Facile preparation of visible light-sensitive layered g-C3N4 for photocatalytic removal of organic pollutants

The graphite-phase carbon nitride (g-C₃N₄) photocatalytic materials were prepared by one-step calcination method to degrade methylene blue (MB) and potassium butyl xanthate (PBX) under visible light irradiation. The prepared g-C₃N₄ photocatalytic materials were investigated in detail by various characterizations, and the experiments showed that the graphitic phase carbon nitride photocatalytic materials were successfully prepared by the one-step calcination method. The material possesses excellent optical properties and strong visible light absorption, thus achieving photocatalytic degradation of MB and PBX. The catalyst dosage, pH, the initial concentration of pollutants have important effects on photocatalytic activity of MB and PBX. The photocatalytic degradation efficiency was 98.99% for MB and 96.83% for PBX under the optimal conditions (catalyst dosage, initial pollutant concentration and pH value were 500 mg L^-1, 20 mg L^-1 and 7, respevtively). The photocatalytic mechanisms on MB and PBX were elucidated. ·OH was the key specie for MB, while ·O₂^- was the key specie for PBX. This study advances the development of photocatalytic technology for mineral wastewater.

Preparation of a novel photocatalytic catalyst PW9@ZnO/Ag and the photocatalytic degradation of butyl xanthate under visible light

Photocatalytic technology is attracting considerable attention for the advantages of low cost and environmentally friendly properties. In this study, a novel photocatalyst PW₉@ZnO/Ag (PZA) was synthesized hydrothermally and characterized by a variety of means. The results indicated that ZnO and Ag NPs were successfully decorated and uniformly dispersed on PW₉ to form the composites. The prepared PZA was applied in the degradation of simulated butyl xanthate (BX) beneficiation wastewater both under the UV light and the xenon lamp, and a maximum degradation of 99.83% was obtained under the visible light with 10% ZnO loading, 1 g/L PZA, initial BX concentration of 20 mg/L, and pH 5.5. The PZA was recovered and reused for 5 times, and the degradation rates remained above 70%. Superoxide radical (·O₂^-) was the main active species for the photocatalytic degradation of BX. The experimental results demonstrate that PZA is a promising photocatalyst, making it a prospective strategy to overcome current challengers in the use of xanthate degradation and beneficiation wastewater treatment under visible light.

Investigation on the evolution of hydrothermal biochar

The objective of this study was to visualize trends and current research status of hydrothermal biochar research through a bibliometric analysis by using CiteSpace software. The original article data were collected from the Web of Science core database published between 2009 and 2020. A visual analysis network of national co-authored, institutional co-authored and author co-authored articles was created, countries, institutions and authors were classified accordingly. By visualizing the cited literature and journal co-citation networks, the main subject distribution and core journals were identified respectively. By visualizing journal co-citations, the main research content was identified. Further the cluster analysis revealed the key research directions of knowledge structure. Keyword co-occurrence analysis and key occurrence analysis demonstrate current research hotspots and new research frontiers. Through the above analysis, the cooperation and contributions of hydrothermal biochar research at different levels, from researchers to institutions to countries to macro levels, were explored, the disciplinary areas of knowledge and major knowledge sources of hydrothermal biochar were discovered, and the development lineage, current status, hotspots and trends of hydrothermal biochar were clarified. The results obtained from the study can provide a reference for scholars to gain a deeper understanding of hydrothermal biochar.

Rational design of mixed ionic-electronic conducting membranes for oxygen transport

The mixed ionic-electronic conducting (MIEC) oxides have generated significant research efforts in the scientific community during the last 40 years. Since then, many MIEC compounds, most of which are based on perovskite oxides, have been synthesized and characterized. These compounds, when heated to high temperatures, form solid ceramic membranes with high oxygen ionic and electrical conductivity. The driving force for oxygen ion transport is the ionic transfer of oxygen from the air as a result of the differential partial pressure of oxygen across the membrane. Electronic and ionic transport in a range of MIEC materials has been studied using the defect theory, particularly when dopants are introduced to the compound of interest. As a result, many types of ionic oxygen transport limits exist, each with a distinct phase shift depending on the temperature and partial pressure of oxygen in use. In combination with theoretical principles, this work attempts to evaluate the research community's major and meaningful achievements in this subject throughout the preceding four decades.

Sedimentary environment and relative sea level changes revealed by marine biological membrane

Marine pollution has a deleterious impact, both on the conditions of the ecosystem and the biodiversity of the ocean. Researchers in the field of marine chemistry have been putting effort into the creation of efficient catalysts for the purification of seawater. There has been extensive research done on membrane technology for the activation of peroxymonosulfate, which is an extremely effective therapy for saltwater. The sediment of QX03, which was obtained from the western coast of Bohai, is located very close to the modern coastline. The uppermost 15 m of this sector were thoroughly analyzed in sedimentary petrology, grain size, shell, and sediment chroma dating to reconstruct the sedimentary environment and relative sea-level during the time period of 44.80 ka cal BP. This indicates that a sea-retreating and retreating process has taken place; VI (5.2-0 m), Terrestrial deposition, is separated into swamp wetlands (VI-1) and flood plain (VI-2). The changes in sedimentary levels had a fairly strong correlation with the changes in sea level. Within the scope of this study, we conducted an in-depth investigation of the innovative membrane technology for the treatment of seawater by means of aqueous phase advanced oxidation close to the Bohai. The results of this study present a prospective technique that could make it possible to use membrane technology in the process of environmental restoration in marine settings.

Heavy metals pollution characteristics and risk assessment in sediments and waters: The case of Tianjin, China

Potential health and ecological risks due to heavy metal pollution in surface waters and sediments were evaluated based on a health risk assessment model and a potential ecological risk index method. Combined with the reclamation progress of Tianjin Nangang Industrial Zone, in China, a survey was carried out in the area dealing with heavy metals concentrations in surface waters and sediments, covering from 2008 to 2018. Specifically, concentrations were determined for As, Cd, Hg, Cu, Pb, and Zn. The results show that As、Cd、Hg、Cu 、Pb、Zn average concentrations in surface water were 0.99 μg/L∼1.27 μg/L, 0.13 μg/L∼0.63 μg/L, 0.03 μg/L∼0.13 μg/L, 1.5 μg/L∼4.65 μg/L, 1.25 μg/L∼4.7 μg/L, 13.5 μg/L∼20.99 μg/L and which average concentrations in sediment were 5.12 mg/kg∼12.34 mg/kg, 0.12 mg/kg∼0.18 mg/kg, 0.04 mg/kg ∼0.087 mg/kg, 13.45 mg/kg∼31.92 mg/kg, 13.2 mg/kg ∼21.26 mg/kg, 21.58 mg/kg ∼77.21 mg/kg, respectively. The background values of the Hailuan River basin near the study area were taken as the reference and compared with the national sediment quality standards a tell us the quality of the sediments in Tianjin Nangang coastal area being good. As regards the characteristics of pollution, heavy metals showed a high concentration in 2008 and then decreased significantly, which related to the dredging of large amounts of contaminated surface sediment during port construction. According to the phase equilibrium partition coefficient (Kp) and temporal and spatial distribution characteristics of heavy metals, sediments can be seen as an obvious sink for lead, with this element being mainly affected by exogenous input in coastal seawater. Zn, As, Cd, and Hg contents in surface water were greatly affected by the endogenous release from sediments. The results of the environmental risk assessment showed that the main environmental health risk of Tianjin coastal waters was carcinogenic, and specifically due to As. The potential heavy metals ecological risk assessment results of surface sediments were mild for the affected areas.

Enhanced H2evolution performance by carbonized SiC/g-C3N4heterojunction under visible-light illumination

In this study, carbonized silicon carbide/graphitic carbon nitride ((SiC/C)/g-C₃N₄) composites were fabricated via a facile calcination method. The optimal SiC/C/g-C₃N₄composite shows an excellent visible-light photocatalytic activity for water splitting, with the highest hydrogen evolution amount being 200.2μmol, which is four times higher than that of pure g-C₃N₄when triethanolamine and platinum (1.0 wt%) are used as the sacrificial agent and cocatalyst, respectively. With an intimate interface between SiC/C and g-C₃N₄, the energy band structure of g-C₃N₄was well engineered for photocatalytic H₂production. This study provides a novel method for fabricating g-C₃N₄-based heterojunctions for application in environmental conservation.

Photocatalytic degradation of amoxicillin and tetracycline by template synthesized nano-structured Ce3+@TiO2 thin film catalyst

Contamination of the aquatic environment with pharmaceutical compounds is a serious environmental concern. The present investigation aims to utilize the Ce³⁺/TiO₂ thin film catalyst to remove of potential antibiotics (amoxicillin and tetracycline) using the less harmful UV-A radiations. Reduced cerium ion-doped TiO₂ is obtained by a simple one-step facile template method using polyethylene glycol as the templating agent. The synthesized catalysts Ce³⁺@TiO₂ (non-template) and Ce³⁺@TiO₂(T) (template) were characterized by spectroscopic methods. The XPS reaffirms the reduced Ce³⁺ dispersed within the titania network, and the AFM showed the surface roughness of the thin films. Detailed physicochemical analyses were conducted to deduce the degradation mechanism, and repeated use of the thin film photocatalyst showed enhanced stability. Significant mineralization of the antibiotics indicates the potential applicability of the photocatalytic catalyst. Furthermore, the presence of Ce³⁺ significantly restricted the recombination of electron/hole pairs in the photo-excited TiO₂ semiconductor and showed enhanced photocatalytic degradation of the antibiotics proceeded predominantly through the •OH.

Kinetics and mechanisms of the carbamazepine degradation in aqueous media using novel iodate-assisted photochemical and photocatalytic systems

The present study investigates the kinetics and mechanisms of carbamazepine (CBZ) degradation using a novel UV/iodate (IO₃^-) system for the first time and explores the influence of process conditions on its degradation. UV/IO₃^- showed high degradation efficiencies in a wide range of pHs, especially under neutral and acidic conditions, indicating that the system can be considered as a promising method to deal with effluents under various pH conditions. Radical scavenging experiments show that both iodine radicals (IO, IO₂ and IO₃) and hydroxyl radicals play an important role in CBZ degradation. Furthermore, the combination of UV/IO₃^- with TiO₂ was studied to explore the potential of the addition of IO₃^- to improve the efficiency of the conventional TiO₂ photocatalytic system. Scavenging experiments indicated that iodine radicals (IO, IO₂ and IO₃) were mainly involved in the degradation of CBZ in the UV/IO₃^-/TiO₂ system, and the reaction mechanism equations were proposed for the first time for the studied UV/IO₃^-/TiO₂ system. Several degradation products and four possible pathways of CBZ degradation were also elucidated using ultra-high-performance liquid chromatography in combination with a quadrupole time-of-flight mass spectrometer (Q-TOF MS). Respirometric tests indicated that the treatment has a positive impact on biomass behavior during subsequent biological purification, highlighting that the developed IO₃^--assisted AOPs are eco-friendly.

Potentially toxic elements in cascade dams-influenced river originated from Tibetan Plateau

Rivers originated from Tibetan Plateau are of great significance due to their environmental sensibility and fragility. However, the pollution of suspended particulate matter (SPM) in these rivers is rarely reported, in particular, the potentially toxic elements (PTEs) contamination. To clarify the status, sources, behavior, and risks of PTEs in SPM, a full investigation was conducted in dams-influenced Lancangjiang River basin. The findings revealed that the PTEs content (mg kg^-1) ranked Mn (766) > V (151.7) > Zn (131.0) > Cr (94.6) > Ni (44.2) > Pb (36.7) > Cu (29.4) > Co (14.6) > Sb (2.6) > Mo (1.6) > Tl (0.78) > Cd (0.48). The multi-index assessment suggested that Sb and Cd were moderately severe to severe enriched PTEs with the enrichment factor values of 10.0 and 8.8 and the geo-accumulation index values of 2.2 and 2.0, respectively, while the rest of PTEs were minor/no enrichment. In contrast, Cr and Ni were major toxic elements in SPM which contributed 25 ± 10%, 24 ± 8% to the total toxic risk index. The high partition coefficients (e.g., 6.1 for Cr) were observed in most PTEs and resulted in the 96.3% of Cr, 85.2% of Zn, 83.6% of Pb, 77.8% of Ni, and 63.2% of Cu transportation in the SPM form. Natural inputs (e.g., soil erosion) are the main source (53.6%∼61.9%) of V, Cr, Mn, Co, Ni, and Tl, while fuel burning contributed 40.9% of Zn, 32.5% of Pb, and 37.3% of Cd. Moreover, 51.2% of Sb was attributed to industrial waste source, while porphyry copper/molybdenum deposits related milltailings were the co-source of Mo (54.4%) and Cu (34.8%). Overall, the PTEs geochemistry of SPM showed the potential in tracing regional environmental change.

Perovskite oxide for emerging photo(electro)catalysis in energy and environment

Using solar energy to catalyse photo-driven processes to address the energy crisis and environmental pollution plays a role in the path to a sustainable society. Many oxide-based materials, especially perovskite oxides, have been widely investigated as catalysts for photocatalysis in energy and environment because of the low-cost and earth-abundant and good performance. At this stage, there is a need to present a scientific-based evaluation of the technologies developed so far and identify the most sustainable technologies and the existing limitations and opportunities for their commercialisation. This work comprehensively investigated the outcomes using various scientometric indices on perovskite oxide-based photo(electro)catalysts for water splitting, nitrogen fixation, carbon dioxide conversion, organic pollutant degradation, current trends and advances in the field. According to the results achieved, efforts in both energy and environment based on perovskite oxides have been initiated in the 1990s and accelerated since the 2010s. China and the United States were identified as the most contributing countries. Based on the results achieved in this study, the main milestones and current trends in the development of this field have been identified. The aim of this research is to provide useful guidelines for the further investigation of perovskite oxide-based catalysts for photoelectrocatalysis and photocatalysis both in energy and environment on the applications such as water splitting, nitrogen fixation, carbon dioxide conversion, and wastewater treatment.

Elimination of amoxicillin using zeolite Y-sea salt as a good catalyst for activation of hydrogen peroxide: Investigating degradation pathway and the effect of wastewater chemistry

The sea contains elements that can play a useful role in catalyzing reactions. Therefore, this research was done to focus on eliminating amoxicillin (AMX) from wastewater utilizing zeolite Y- sea salt catalyst in the presence of H₂O₂. The influences of furnace temperature (200-500 °C) and time duration in the furnace (1-4 h) were optimized during catalyst generation. Also, the effects of different parameters on AMX removal, such as pH (5.0-9.0), catalyst dose (0-10 g.L^-1), AMX concentration (50-300 mg.L^-1), contact time (10-130 min), and H₂O₂ concentration (0-6 mL/100 mL distilled water) were investigated. Different analyses like Brunauer-Emmett-Teller (BET), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) were conducted to reveal catalyst properties. The BET-specific surface area of the catalyst (12.69 m²g^-1) insignificantly (p-value > 0.05) changed after AMX removal (13.04 m²g^-1), indicating the strength of the prepared catalyst. The active groups of N-H, O-H-O, O-Si-O, C-H, Si-O-Si, and Si-O-Al were determined in the catalyst structure. The highest removal of AMX (93%) was achieved in the zeolite-sea salt/H₂O₂ system at a pH level of 6.0 and an H₂O₂ concentration of 0.1 mL/100 mL. Elimination of the AMX followed pseudo-first-order kinetics. The catalyst was reclaimed up to 7 times and the removal efficiency was suitable up to the fifth stage. The by-products and reaction pathways were investigated by gas chromatography-mass spectrometry (GC-MS). The results showed that zeolite-sea salt can be utilized as an H₂O₂ activator for the effective degradation of AMX from wastewater.

Steered polymorphic nanodomains in TiO2 to boost visible-light photocatalytic oxidation

A breakthrough in enhancing visible-light photocatalysis of wide-bandgap semiconductors such as prototypical titania (TiO₂) via cocatalyst decoration is still challenged by insufficient heterojunctions and inevitable interfacial transport issues. Herein, we report a novel TiO₂-based composite material composed of in situ generated polymorphic nanodomains including carbon nitride (C₃N₄) and (001)/(101)-faceted anatase nanocrystals. The introduction of ultrafine C₃N₄ results in the generation of many oxygen vacancies in the TiO₂ lattice, and simultaneously induces the exposure and growth of anatase TiO₂(001) facets with high surface energy. The photocatalytic performance of C₃N₄-induced TiO₂ for degradation of 2,4-dichlorophenol under visible-light irradiation was tested, its apparent rate being up to 1.49 × 10⁻² min⁻¹, almost 3.8 times as high as that for the pure TiO₂ nanofibers. More significantly, even under low operation temperature and after a long-term photocatalytic process, the composite still exhibits exceptional degradation efficiency and stability. The normalized degradation efficiency and effective lifespan of the composite photocatalyst are far superior to other reported modified photocatalysts.

A novel TiO₂-based composite material composed of in situ generated biomimetic polymorphic nanodomains including carbon nitride (C₃N₄) and (001)-/(101)-faceted anatase nanocrystals is reported.

Highly efficient photo-degradation of cetirizine antihistamine with TiO2-SiO2 photocatalyst under ultraviolet irradiation

Photocatalysis is an extraordinary and vastly researched topic; there is a need to find new ways to support producing composite materials that are cost-effective, efficient and have a low environmental impact. The investigation was undertaken on syn TiO2 by depositing it on silica. The results elucidate the positive effect on photocatalysis activity and the macroscopic structure on which the TiO2 is formed. For the analysis of photocatalyst, various characterisation measurements were undertaken, such as XRD, FTIR, DRS, FESEM, TEM, RS, and BET. The accumulated TiO2 onto the surface of SiO2 stabilised its transformation of the phase from anatase to rutile, resulting in decreased particle size and enhancing its photocatalytic activity under UV irradiation. The concentration of OH• radicals was determined using terephthalic acid as a probe molecule to determine its role in the photocatalytic degradation of antihistamine. The results of BET analysis showed that the syn TiO2-SiO2 sample has a large specific surface area of 192.6 m2 g−1. Maximum degradation of cetirizine (about 97%) was achieved with 80% TiO2-20% SiO2 (TS-4). Recyclability test confirmed that 80% TiO2-20% SiO2 sample was stable up to six cycles.