Study on the mechanism of copper-ammonia complex decomposition in struvite formation process and enhanced ammonia and copper removal

Copper hexacyanoferrate/carbon sheet combination with high selectivity and capacity for copper removal by pseudocapacitance

The efficient capture of copper ions (Cu2+) in wastewater has dual significance in pollution control and resource recovery. Prussian blue analog (PBA)-based pseudocapacitive materials with open frameworks and abundant metal sites have attracted considerable attention as capacitive deionization (CDI) electrodes for copper removal. In this study, the efficiency of copper hexacyanoferrate (CuHCF) as CDI electrode for Cu2+ treating was evaluated for the first time upon the successful synthesis of copper hexacyanoferrate/carbon sheet combination (CuHCF/C) by introducing carbon sheet as conductive substrate. CuHCF/C exhibited significant pseudocapacitance and high specific capacitance (52.92 F g-1) through the intercalation, deintercalation, and coupling of Cu+/Cu2+ and Fe2+/Fe3+ redox pairs. At 0.8 an applied voltage and CuSO4 feed liquid concentration of 100 mg L-1, the salt adsorption capacity was 134.47 mg g-1 higher than those of most reported electrodes. Moreover, CuHCF/C demonstrated excellent Cu2+ selectivity in multi-ion coexisting solutions and in actual wastewater experiments. Density functional theory (DFT) calculations were employed to elucidate the mechanism. This study not only reveals the essence of Cu2+ deionization by PBAs pseudocapacitance with promising potential applications but also provides a new strategy for selecting efficient CDI electrodes for Cu2+ removal.

Emerging trends in research and development on earth abundant materials for ammonia degradation coupled with H2 generation

Ammonia, as an essential and economical fuel, is a key intermediate for the production of innumerable nitrogen-based compounds. Such compounds have found vast applications in the agricultural world, biological world (amino acids, proteins, and DNA), and various other chemical transformations. However, unlike other compounds, the decomposition of ammonia is widely recognized as an important step towards a safe and sustainable environment. Ammonia has been popularly recommended as a viable candidate for chemical storage because of its high hydrogen content. Although ruthenium (Ru) is considered an excellent catalyst for ammonia oxidation; however, its high cost and low abundance demand the utilization of cheaper, robust, and earth abundant catalyst. The present review article underlines the various ammonia decomposition methods with emphasis on the use of non-noble metals, such as iron, nickel, cobalt, molybdenum, and several other carbides as well as nitride species. In this review, we have highlighted various advances in ammonia decomposition catalysts. The major challenges that persist in designing such catalysts and the future developments in the production of efficient materials for ammonia decomposition are also discussed.

Ammonium nanochelators in conjunction with arginine-specific enzymes in amperometric biosensors for arginine assay

Amino acid L-arginine (Arg), usually presented in food products and biological liquids, can serve both as a useful indicator of food quality and an important biomarker in medicine. The biosensors based on Arg-selective enzymes are the most promising devices for Arg assay. In this research, three types of amperometric biosensors have been fabricated. They exploit arginine oxidase (ArgO), recombinant arginase I (ARG)/urease, and arginine deiminase (ADI) coupled with the ammonium-chelating redox-active nanoparticles. Cadmium-copper nanoparticles (nCdCu) as the most effective nanochelators were used for the development of ammonium chemosensors and enzyme-coupled Arg biosensors. The fabricated enzyme/nCdCu-containing bioelectrodes show wide linear ranges (up to 200 µM), satisfactory storage stabilities (14 days), and high sensitivities (A⋅M-1⋅m-2) to Arg: 1650, 1700, and 4500 for ADI-, ArgO- and ARG/urease-based sensors, respectively. All biosensors have been exploited to estimate Arg content in commercial juices. The obtained data correlate well with the values obtained by the reference method. A hypothetic scheme for mechanism of action of ammonium nanochelators in electron transfer reaction on the arginine-sensing electrodes has been proposed.

A review of struvite crystallization for nutrient source recovery from wastewater

Nutrient recovery from wastewater not only reduces the nutrient load on water resources but also alleviates the environmental problems in aquatic ecosystems, which is a solution to achieve a sustainable society. Besides, struvite crystallization technology is considered a potential nutrient recovery technology because the precipitate obtained can be reused as a slow-release fertilizer. This review presents the basic properties of struvite and the theory of the basic crystallization process. In addition, the possible influencing variables of the struvite crystallization process on the recovery efficiency and product purity are also examined in detail. Then, the advanced auxiliary technologies for facilitating the struvite crystallization process are systematically discussed. Moreover, the economic and environmental benefits of the struvite crystallization process for nutrient recovery are introduced. Finally, the shortcomings and inadequacies of struvite crystallization technology are presented, and future research prospects are provided. This work serves as the foundation for the future use of struvite crystallization technology to recover nutrients in response to the increasingly serious environmental problems and resource depletion.

Recyclable fluorescence sensing based on copper clusters for simultaneous determination of copper ions and ammonia

A one-step strategy for synthesizing fluorescent copper clusters stabilized by L-cysteine has been successfully established in aqueous solutions. The direct determination of copper ions was realized by the fluorescence enhancement phenomenon caused by the preparation and aggregation process. At the same time, ammonia treatment can lead to rapid fluorescence quenching, resulting from the influence on the aggregation behavior of Cu clusters, while the fluorescence can be recovered by the continuous addition of copper ions. Therefore, a recyclable fluorescence sensing system is constructed for the simultaneous determination of copper ions and ammonia. This method is simple, anti-interference and has been successfully applied to the determination of environmental samples.

Nutrient released characteristics of struvite-biochar fertilizer produced from concentrated sludge supernatant by fluidized bed reactor

With the exacerbating water eutrophication globally, it is important to recover nitrogen (N) and phosphorus (P) from sewage for recycle. In this study, coconut shell biochar and ethylene diamine tetraacetic acid (EDTA) were added into the designed fluidized bed reactor (FBR) to create struvite-biochar. N and P released from struvite-biochar and the recovery efficiency of N and P from concentrated sludge supernatant were analyzed. Results showed that the optimal operation condition for hydraulic retention time (HRT), pH, Mg/P molar ration, and addition amount EDTA were 90 min, 9.5, 1.2, and 0.2 g/L, respectively. The recovery efficiency of NH₄⁺-N and PO₄^3--P, and purity struvite for FBR were 34.41%-38.05%, 64.95-68.40%, and 84.15%, respectively. The recovery efficiency of NH₄⁺-N and PO₄^3--P were respectively increased by 7.23% and 5.36% when FBR with addition of 0.33 g/L coconut shell biochar, but purity struvite from struvite-biochar decreased by 45.70%. Contents of As, Cd, Pb, and Cr in struvite and struvite-biochar were all lower than Chinese Standard Limits of Fertilizer. Compared to commercial chemical fertilizer, such as superphosphate and urea, struvite-biochar and struvite have slowly released N and P. The amounts of released P, NO₃^--N and NH₄⁺-N from struvite-biochar were higher than struvite during the five leaching times. Compared with struvite, the total amounts of released P, NO₃^--N and NH₄⁺-N from struvite-biochar increased by 4.9%, 3.5% and 8.3%, respectively. Therefore, it is valuable to add biochar into FBR to recovery N and P from concentrated sludge supernatant and make struvite-biochar as a slow-release fertilizer.

Electrochemical Performance of Layer-Structured Ni0.8Co0.1Mn0.1O2 Cathode Active Materials Synthesized by Carbonate Co-Precipitation

The layered Ni-rich NiCoMn (NCM)-based cathode active material Li[Ni_xCo_(1-x)/2Mn_(1-x)/2]O₂ (x ≥ 0.6) has the advantages of high energy density and price competitiveness over an LiCoO₂-based material. Additionally, NCM is beneficial in terms of its increasing reversible discharge capacity with the increase in Ni content; however, stable electrochemical performance has not been readily achieved because of the cation mixing that occurs during its synthesis. In this study, various layer-structured Li_1.0[Ni_0.8Co_0.1Mn_0.1]O₂ materials were synthesized, and their electrochemical performances were investigated. A NiCoMnCO₃ precursor, prepared using carbonate co-precipitation with Li₂CO₃ as the lithium source and having a sintering temperature of 850 °C, sintering time of 25 h, and metal to Li molar ratio of 1.00-1.05 were found to be the optimal parameters/conditions for the preparation of Li_1.0[Ni_0.8Co_0.1Mn_0.1]O₂. The material exhibited a discharge capacity of 160 mAhg^-1 and capacity recovery rate of 95.56% (from a 5.0-0.1 C-rate).

Sorption Preconcentration and Analytical Determination of Cu, Zr and Hf in Waste Samarium–Cobalt Magnet Samples

We developed a method of sorption determination via the atomic emission of Cu, Zr and Hf metals in the waste of samarium–cobalt magnets. This method was based on the preconcentration of impurities using S- and N-containing heterochain sorbents, with further determination of the analytes via inductively coupled plasma atomic emission spectrometry (ICP-OES). Different sorbents such as PED (polyethelendiamine), TDA (polythiodimethanamine), PhED (N-phenylpolyethediamine) and PTE (polythioether) were tested for Ti, Cu, Zr, Nb and Hf extraction. The PTE sorbent ensured the maximum extraction of the analytes (recovery 60% for Ti, 80% for Nb, 95–100% for Cu, Zr and Hf) and thus was selected for further research. Additionally, various acidities of chloride solution (0.01–1 M HCl) were investigated for metal sorption. Under the optimised sorption conditions, trace impurities of Cu, Zr and Hf were determined using ICP-OES with a relative standard deviation of less than 5%. The obtained results were confirmed by the added–found method and cross-method experiments. The detection limits (DLs) were 1.5, 2, 0.15, 2 and 0.75 µg/L for Ti, Cu, Zr, Nb and Hf, respectively. The proposed method can be successfully used for the determination of various microelements in other waste REE-magnetic materials.

Direct Observation of Ammonia Storage in UiO-66 Incorporating Cu(II) Binding Sites

The presence of active sites in metal-organic framework (MOF) materials can control and affect their performance significantly in adsorption and catalysis. However, revealing the interactions between the substrate and active sites in MOFs at atomic precision remains a challenging task. Here, we report the direct observation of binding of NH3 in a series of UiO-66 materials containing atomically dispersed defects and open Cu(I) and Cu(II) sites. While all MOFs in this series exhibit similar surface areas (1111-1135 m2 g-1), decoration of the -OH site in UiO-66-defect with Cu(II) results in a 43% enhancement of the isothermal uptake of NH3 at 273 K and 1.0 bar from 11.8 in UiO-66-defect to 16.9 mmol g-1 in UiO-66-CuII. A 100% enhancement of dynamic adsorption of NH3 at a concentration level of 630 ppm from 2.07 mmol g-1 in UiO-66-defect to 4.15 mmol g-1 in UiO-66-CuII at 298 K is observed. In situ neutron powder diffraction, inelastic neutron scattering, and electron paramagnetic resonance, solid-state nuclear magnetic resonance, and infrared spectroscopies, coupled with modeling reveal that the enhanced NH3 uptake in UiO-66-CuII originates from a {Cu(II)···NH3} interaction, with a reversible change in geometry at Cu(II) from near-linear to trigonal coordination. This work represents the first example of structural elucidation of NH3 binding in MOFs containing open metal sites and will inform the design of new efficient MOF sorbents by targeted control of active sites for NH3 capture and storage.

Resin-Mediated pH Control of Metal-Loaded Ligand Exchangers for Selective Nitrogen Recovery from Wastewaters

Highly selective separation materials that recover total ammonia nitrogen (i.e., ammonia plus ammonium, or TAN) from wastewaters as a pure product can supplement energy-intensive ammonia production and incentivize pollution mitigation. We recently demonstrated that commercial acrylate cation exchange polymer resins loaded with transition metal cations, or metal-loaded ligand exchangers, can recover TAN from wastewater with high selectivity (TAN/K+ equilibrium selectivity of 10.1) via metal-ammine bond formation. However, the TAN adsorption efficiency required further improvement (35%), and the optimal concentration and pH ranges were limited by both low ammonia fractions and an insufficiently strong resin carboxylate-metal bond that caused metal elution. To overcome these deficiencies, we used a zinc-acrylate ligand exchange resin and a tertiary amine acrylic weak base resin (pH buffer resin) together to achieve resin-mediated pH control for optimal adsorption conditions. The high buffer capacity around pH 9 facilitated gains in the adsorbed TAN per ligand resin mass that enhanced the TAN adsorption efficiency to greater than 90%, and constrained zinc elution (below 0.01% up to 1 M TAN) because of decreased ammonia competition for zinc-carboxylate bonds. During TAN recovery, resin-mediated pH buffering facilitated recovery of greater than 99% of adsorbed TAN with 0.2% zinc elution, holding the pH low enough to favor ammonium but high enough to prevent carboxylate protonation. For selective ion separation, solid phase buffers outperform aqueous buffers because the initial solution pH, the buffering capacity, and the ion purity can be independently controlled. Finally, because preserving the resin-zinc bond is crucial to sustained ligand exchange performance, the properties of an ideal ligand resin functional group were investigated to improve the properties beyond those of carboxylate. Ultimately, ligand exchange adsorbents combined with solid pH buffers can advance the selective recovery of nitrogen and potentially other solutes from wastewaters.

Fluorescent and colorimetric assay for determination of Cu(II) and Hg(II) using AuNPs reduced and wrapped by carbon dots

To improve the accuracy and specificity of visual sensors for detecting Cu(II) and Hg(II), a fluorescent and colorimetric dual-modal sensor based on Au nanoparticles (AuNPs) prepared by using carbon dots (CDs) was designed. If a sensor is to be applied for the detection of targets in different environmental backgrounds, it needs to have high stability against heat, pH, and salt. To this end, CD-wrapped AuNP probes were fabricated by the in situ reaction of chloroauric acid and reductive CDs. The reductive CDs were prepared with hyperbranched polyethyleneimine (HPEI) as a carbon source. HPEI-CDs not only acted as a reducing agent but also as an excellent stabilizer in the preparation and detection application of the AuNPs. Based on multiple signal responses, including color, UV-Vis absorption, and fluorescence intensity, the HPEI-CD/AuNP nanosensor was used to realize the detection of Cu²⁺ and Hg²⁺ in the linear range 9.0×10^-10-9.0×10^-4 M and 9.0×10^-7-9.0×10^-5 M with low detection limits of 75.6 nM and 281 nM, respectively. In tap water analysis, the recovery of Cu²⁺ and Hg²⁺ by fluorescent range from 109.98-113.31% and 100.65-100.81%, and the RSD values were 0.1159-1.6317% and 3.2-5.4%, respectively. The recovery of Cu²⁺ and Hg²⁺ by colorimetric detection were 99.72-100.14% and 99.88-100.12%, and RSD values were 0.6527-0.6842% and 0.4400-0.8386%, respectively. Importantly, this sensor was applied to the accurate and sensitive detection of Cu²⁺ and Hg²⁺ in tap water and sea water. The multimode readout nanosensor exhibited strong potential for achieving simultaneous detection of two different heavy metal ions in practical applications. The novel multi-mode readout carbon dots/AuNPs sensor for Cu²⁺ and Hg²⁺ detectionshowed high sensitivity and selectivity.

A review on the incorporation and potential mechanism of heavy metals on the recovered struvite from wastewater

Phosphorus, as a non-renewable element, is flowing out too fast in the past decades. To sustain the development of this globally scarce resource, efficient measures were taken to recover more phosphorus in the struvite form from wastewater. However, heavy metals in the wastewater might produce an inhibitory effect on phosphorus recovery, and even worse, pollutants might be incorporated in/onto the crystals precipitated. Impurities on struvite will reduce the quality of struvite as a potential slow-release fertilizer and affect the safe application of struvite in agriculture. This review aims to identify the trends in the literature to present the residues of heavy metals in struvite. It summarizes the current status in the residues of main metal elements on crystals and its response to wastewater properties, composition, and oxidation state of metals. The adsorption process and potential adsorption mechanism of heavy metals during the struvite crystallization are deeply explored, which might determine the latter release rate of metals when applying into the soil. Possible solutions are further provided to minimize the amounts of heavy metals mainly through adjusting operational conditions or employing pretreatment methods. Finally, this review critically analyzes the limitation gap between theory and actual generalization and potential application of struvite products in the market, and corresponding perspectives in the future are given to safely utilize the phosphorus resource from wastewater in the form of struvite.

Co-precipitation of Cu and Zn in precipitation of struvite

Struvite recovered from wastewater can be used as a slow-release fertilizer. Nevertheless, hazardous metals easily precipitated with struvite would increase the ecological risk for its agricultural use. In this study, the influence of individual and coexistence of Cu and Zn on the precipitation of struvite was investigated. The loading of Cu and/or Zn in precipitates increased with the increase of initial metal concentrations (0.1-100 mg/L). Quantitative X-ray diffraction (QXRD) analysis revealed that the increase of Cu and/or Zn level in reaction solution disturbed crystal growth of struvite and promoted the formation of amorphous phase(s). Scanning electron microscopy (SEM) revealed the pit formation on struvite crystal surfaces, combined with X-ray photoelectron spectroscopy (XPS) data, the results indicated a surface interaction for the formation of Cu-OH and Cu-NH₃ on struvite surface at Cu of 0.1-10 mg/L. With the increase of Cu to 25-100 mg/L, the precipitation of amorphous Cu phosphate(s) was confirmed by XPS and QXRD. At Zn of 0.1-10 mg/L, the enrichment of Zn-PO₄ and Zn-OH on struvite surface was observed, whereas, the precipitation of amorphous Zn hydroxide(s) was confirmed at Zn of 25-100 mg/L. At Cu and Zn co-existed solution, the decrease of Cu-PO₄ and increase of Zn-PO₄ suggested the competitive binding of PO₄ between Cu and Zn. In addition, the formation of amorphous Mg hydroxide(s) and phosphate(s) was detected regardless of the addition of Cu in solutions. The overall results revealed that the existence of Cu and Zn during struvite formation can greatly affect its content by formation of different metal-containing products.

Development and simulation of a struvite crystallization fluidized bed reactor with enhanced external recirculation for phosphorous and ammonium recovery

Recovering nitrogen and phosphorus from waste water in the form of struvite is an effective way to recycle resources. The insufficient purity of the resulting struvite and the large loss of nitrogen and phosphorus are the challenges at present. Therefore, it is urgent to develop innovative method in struvite crystallization process for efficient nitrogen and phosphorus recovery. This study proposed a crystallization method to reduce the loss of nitrogen and phosphorus by a struvite fluidized bed reactor (FBR) with optimized structure and operation conditions. The properties of struvite obtained under various conditions in the reactor were studied, and the internal operating conditions of the reactor were simulated with COMSOL Multiphysics to verify the effectiveness of the reactor optimization. This reactor achieved stable operation under the conditions of N/P = 1:1 and pH = 9.0. The purity of struvite obtained reached 98.5%, the conversion rate of ammonia nitrogen reached 97.2%, and struvite crystals could grow to 84 μm within 24 h. The simulation results showed that the Venturi tubes installed at multiple locations increased the turbulent energy to 4 × 10^-4 m²/s², which greatly improved the mass transfer efficiency. The trajectory of the crystal particles was consistent with the fluid flow field, which promoted the purification and growth of the crystal. In general, the new FBR with enhanced external recirculation would be a very feasible way to improve crystal growth and crystal purification of struvite, and it could enhance the recovery efficiency of nitrogen and phosphorus with reduced cost.

Novel Green Method for the Synthesis of Monoacetin over Bifunctional Cu-Cr Phosphates under the CO2 Atmosphere

Monoacetin was synthesized using a novel green method in which acetonitrile was hydrolyzed and then esterified with glycerol over Cu-Cr phosphates under the CO₂ atmosphere. Monoacetin was synthesized with high yield (87.6% glycerol conversion and 86.3% monoacetin selectivity) through this one-pot cascade method. In this process, acetonitrile can react with water to form acetamide and further undergo esterification with glycerol. There are two main reasons for obtaining monoacetin in high yield: (1) the interaction of CO₂ with high-temperature liquid water enhances the acid strength of the reaction system and then promotes the activation of acetonitrile; and (2) the introduction of Cr species causes a synergistic effect between Cu and Cr species to adjust the acidity and basicity of the catalyst. The introduction of Cr species converts eight-coordinated Cu²⁺ into four-coordinated Cu²⁺ to improve the acidity of the catalyst. The introduction of Cr species also causes the surface oxygen to be transformed into lattice oxygen to enhance the basicity of the catalyst. These bimetallic phosphate materials may provide a new pathway for the application of acid-base bifunctional catalytic reactions.

New progress of ammonia recovery during ammonia nitrogen removal from various wastewaters

The recovery of ammonia-nitrogen during wastewater treatment and water purification is increasingly critical in energy and economic development. The concentration of ammonia-nitrogen in wastewater is different depending on the type of wastewater, making it challenging to select ammonia-nitrogen recovery technology. Meanwhile, the conventional nitrogen removal method wastes ammonia-nitrogen resources. Based on the circular economy, this review comprehensively introduces the characteristics of several main ammonia-nitrogen source wastewater plants and their respective challenges in treatment, including municipal wastewater, industrial wastewater, livestock and poultry wastewater and landfill leachate. Furthermore, we introduce the main methods currently adopted in the ammonia-nitrogen removal process of wastewater from physical (air stripping, ion exchange and adsorption, membrane and capacitive deionization), chemical (chlorination, struvite precipitation, electrochemical oxidation and photocatalysis) and biological (classical and typical activated sludge, novel methods based on activated sludge, microalgae and photosynthetic bacteria) classification based on the ammonia recovery concept. We discuss the applicable methods of recovering ammonia nitrogen in several main wastewater plants. Finally, we prospect the research direction of ammonia removal and recovery in wastewater based on sustainable development.

The role of reagent adding sequence in the NH4+-N recovery by MAP method

Ammonium-nitrogen (NH₄⁺-N) recovery from high concentration of NH₄⁺-N-containing wastewater by struvite (MgNH₄PO₄·6H₂O, MAP) precipitation method has been realized, but whether NH₄⁺-N recovery under different reagent adding sequence of NaOH, solid Mg salt and P salt can generate different effects, remains ambiguous. In view of the problem, four modes to add reagents were investigated in detail on the formation of struvite. The results show that the Mode IV (M-IV, i.e. using 50% NH₄⁺-N wastewater to dissolve completely the Mg salt and the P salt, respectively and then simultaneously poured into a beaker to mix the solution evenly and adjust the pH to 9.5.) has the highest NH₄⁺-N recovery efficiency (90.80%) and the maximum mass of precipitates (896 mg) because of the more amount of alkali and initial seed formation. From the morphology of the obtained precipitates, it can be seen that sample M-IV is more loose and porous than the others. XRD patterns show that the four products under the different modes basically agree with the standard MAP.

Removal of chelated heavy metals from aqueous solution: A review of current methods and mechanisms

Water contamination with heavy metal ions and organic compounds such as citrate, ethylenediaminetetraacetic acid, tartrate, pharmaceuticals, surfactants and natural organic matter, is a serious problem in the natural environment. Although many methods have been effectively applied to the removal of heavy metal complexes from aqueous solution, there is a lack of information available on the mechanisms, advantages and disadvantages of these various methods. This review summarizes the various treatment methods applied to the removal of heavy metal complexes, with a summary of the mechanisms of action and recent research progress. The methods reviewed in detail include electrolysis, membrane separation, adsorption, precipitation, replacement-coprecipitation, TiO₂ photocatalysis and Fenton oxidation-precipitation, with the advantages and disadvantages of each method discussed. Furthermore, the heavy metal complex removal mechanisms are analyzed comprehensively. Results show that the adsorption method exhibited unique merits, showing much promise for future development. Finally, this review comprehensively analyzes future prospects and developments in methods for removal of chelated heavy metals.

The long-term effects of hexavalent chromium on anaerobic ammonium oxidation process: Performance inhibition, hexavalent chromium reduction and unexpected nitrite oxidation

The toxicity of hexavalent chromium (Cr(VI)) is one of the challenges in implementing Anammox process to ammonium-rich wastewater treatment. However, the response of Anammox process to Cr(VI) stress and the inhibition mechanism remain unclear. Here, two Anammox UASB reactors were operated for 285 days under different Cr(VI) stresses. The results showed Anammox performance was not affected at low Cr(VI) concentration (i.e., 0-0.5 mg L^-1), but was severely inhibited at 0.8 mg L^-1. Attempts to domesticate Anammox process to higher Cr(VI) by lowering nitrogen loading rate were failed. Examination of Cr(VI) fate showed the occurrence of extracellular and intracellular Cr(VI) reduction to Cr(III). The inhibition was ascribed to the significant intracellular Cr(VI) reduction, accounting for 99.78% of the total Cr(VI) reduction. Moreover, under long-term Cr(VI) exposure, most nitrite was oxidized to nitrate. But microbial community showed no enrichment of Cr(VI) reducing bacteria and other nitrogen transformation-related bacteria.

Simultaneous adsorption of As(III), Cd(II) and Pb(II) by hybrid bio-nanocomposites of nano hydroxy ferric phosphate and hydroxy ferric sulfate particles coating on Aspergillus niger

To develop an efficient, convenient and cost-effective method to simultaneously remove pollution of As(III), Cd(II) and Pb(II) in wastewater, a strategy to fabricate hybrid bio-nanocomposites ((n-HFP + n-HFS)@An) of nano hydroxy ferric phosphate (n-HFP) and hydroxy ferric sulfate (n-HFS) particles coating on Aspergillus niger was applied. The scanning electron microscope and energy dispersive spectrum analyses showed that (n-HFP + n-HFS)@An composites had been successfully developed which well solved the self-agglomeration problem of the nano particles. Comparing to the bulk nanoparticles, the adsorption rates of the (n-HFP + n-HFS)@An composites for the three metals were promoted 145.34, 28.98 and 25.18% and reached 76.84, 73.62 and 94.31%, respectively. Similarly, the adsorption capacities for As(III), Cd(II), and Pb(II) were 162.00, 205.83 and 730.79 mg/g, respectively. Moreover, the pseudo-second-order kinetic model was more relevant to the adsorption on the three metals by (n-HFP + n-HFS)@An, and adsorbing As(III) was fitted to the Freundlich isotherm model, while the adsorption on Cd(II) or Pb(II) was related to the Langmuir isotherm model. In addition, the adsorption of Cd(II) and Pb(II) was associated with transformation of hydroxyl groups and precipitation with phosphate. As(III) was adsorbed through exchange between AsO₂^- and SO₄^2- in the (n-HFP + n-HFS)@An composites.

The application of aged refuse in nitrification biofilter: Process performance and characterization

High adsorption capacity, good biocompatibility and low cost are highly demanded for biofilter used in ammonium-rich wastewater treatment. In this study, we used SEM, BET, XRD and 16S rRNA to document the evidence for good performance in adsorption and biodegradation in aged refuse. Parallel experiment between raw and inert refuse showed ammonium adsorption occurred at the initial week, with the highest ammonium removal efficiency of 90.36%, but saturated during the subsequent long-term operation. Meanwhile, over 6months' operation of an aged refuse biofilter was conducted to confirm that nitrification was the main pathway of ammonium conversion. The maximum nitrogen loading rate could reach up to as high as 1.28kg/m³/d, with ammonium removal efficiency at 99%. Further, high nitrifier biodiversity were detected with 'Nitrosomonas' and 'Nitrospira' in domination in the refuse. However, Nitrospira would outcompete Nitrosomonas under the oxygen limiting condition and resulted in the failure of partial nitrification. The physicochemical and biological analysis show that biodegradation is the main ammonium conversion pathway, which is the critical finding of this work. This investigation would help to accelerate the application of the aged refuse process in ammonium-rich wastewater treatment.

Influence of process parameters on the heavy metal (Zn2+, Cu2+ and Cr3+) content of struvite obtained from synthetic swine wastewater

Struvite recovered from swine wastewater can be used as a good slow release fertilizer. Nevertheless, the presence of heavy metals would be easily precipitated with struvite and increase the ecological risk for its agricultural use. This paper investigated the possibility of using process variables for heavy metal (Cu²⁺, Zn²⁺ and Cr³⁺) minimization during struvite crystallization in swine wastewater. The heavy metal content, effect ratios (ER) of the citric acid concentration under varying conditions were tested and their SEM, EDS and XRD patterns were compared for morphology analysis. The results show that an increase in pH decreased the content of Cu, Zn and Cr in recovered precipitates. Heavy metal content in the precipitates increased markedly with their initial concentrations in the solution. The effect ratio calculation indicates that Cr has the strongest co-precipitation potential, followed by Zn and Cu. An increase in citric acid concentration reduced the heavy metal removal efficiency (14.3, 27.7 and 28.1% for Cu, Zn and Cr, respectively) but did not decrease their content in struvite precipitates. What is more, increase of total ammonia nitrogen (TAN) to soluble phosphate molar ratio significantly decreased Cu, Zn removal efficiency (52.2 and 50% respectively), while Mg:PO₄P molar ratio had much less effect.

Removal of ammonia-nitrogen in wastewater using a novel poly ligand exchanger-Zn(II)-loaded chelating resin

In this study, a novel poly ligand exchanger-Zn(II)-loaded resin was designed to effectively remove ammonia-nitrogen (NH₃-N) from wastewater. The surface morphology and structure of the Zn-loaded resin were characterized using scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) and Fourier transform infrared spectroscopy (FTIR), respectively. SEM shows the surfaces of the Zn(II)-loaded resin were rough and nonporous and EDS demonstrated that Zn²⁺ was loaded onto the resin successfully. In addition, the combination form of Zn(II) with NH₃-N adsorption reagent was revealed by FTIR spectra; the complex could be R-N-R-O-Zn-O-R-N-R and R-N-R-(O-Zn)₂. The kinetics and equilibrium of the NH₃-N adsorption onto the Zn(II)-loaded resin has been investigated. The effects of pH, reaction time, and temperature on NH₃-N removal from wastewater by Zn(II)-loaded resin were investigated, and the results showed that the maximum adsorption capacity reached 38.55 mg/g at pH 9.54 at 298 K in 240 min. The adsorption ability of the modified resin decreased with an increase in temperature. Moreover, the NH₃-N adsorption followed a pseudo-second-order kinetic process. The kinetic data demonstrated that the adsorption process might be limited by a variety of mechanisms. The study can provide the scientific foundation for the extensive application of a novel poly ligand exchanger-Zn(II)-loaded resin to remove NH₃-N from wastewater.

Insights into the role of extracellular polymeric substances in Zn2+ adsorption in different biological sludge systems

The adsorption behavior of Zn²⁺ in four different biological sludge systems, i.e. activated sludge, denitrification sludge, short-cut nitrification sludge, and anammox granules, was investigated. The results indicated that all sludge samples possessed considerable potential for Zn²⁺ adsorption. Short-cut nitrification sludge possessed the highest Zn²⁺ maximum adsorption capacity (q_m) of 36.4 mg g SS^-1, which was much higher than other sludges applied (12.8-14.7 mg g SS^-1). Besides, the adsorption rate for short-cut nitrification sludge was fastest among the four types of sludge after fitting with a pseudo-second-order rate equation. Comparing with the physicochemical properties of the four sludges, the soluble extracellular polymeric substances (EPS), especially soluble polysaccharide (PS), played a prior role in binding metal cations (i.e., Zn). The present study also showed that with less than 30% of Zn²⁺ trapped by EPS, 61.6-71.9% of Zn²⁺could be harvested directly by cells, indicating that the protecting capability by EPS was limited. Therefore, it is important to remove metal ions as early as possible if the activated sludge processes encountered high stress of heavy metal. Graphical abstract ᅟ.

Granulation process in an expanded granular sludge blanket (EGSB) reactor for domestic sewage treatment: Impact of extracellular polymeric substances compositions and evolution of microbial population

In this study, an expanded granular sludge blanket (EGSB) reactor was used for the treatment of low-strength domestic sewage and the sludge granulation process was systematically investigated. At an optimized hydraulic retention time (HRT) of 5 h, up-flow velocity (V_up) of 1.9 m/h, and organic loading rate (OLR) of 2.16 kg COD/m³/d, the average COD removal efficiency was 71.5 ± 2.3%. Completely granular sludge can be observed after 107 d of continuous operation. Analysis of the distribution and composition of the extracellular polymeric substances (EPS) indicates that the tightly bound EPS (TB-EPS) content shows an increasing trend, while the loosely bound EPS (LB-EPS) content did not significantly alter after the granular sludge was formed. The three-dimensional excitation-emission matrix technique (3D-EEM) confirms that aromatic protein-like substances are of key importance to sludge granulation. High-throughput sequencing analysis indicates that the metabolism shifted from hydrogenotrophic (Methanobaterium) to aceticlastic methanogens (Methanosaeta) during sludge granulation.

Hydrothermal Treatment of Arsenic Sulfide Residues from Arsenic-Bearing Acid Wastewater

Arsenic sulfide residue (ASR), a by-product from the treatment of arsenic-bearing acidic wastewater, is abundantly generated but not properly disposed of in China. The utilization of such high-content arsenic waste residue is limited by the market. The traditional methods of stabilization/solidification (S/S) by lime cement or iron salt have a large mass/volume addition, high dumping cost and secondary pollution risk. In this paper, hydrothermal technology was used to treat three kinds of ASRs obtained from different smelters to minimize waste. The leaching toxicity and chemical speciation of the generated products was also evaluated by TCLP and BCR analyses. It was found that the hydrothermal treatment could greatly reduce the volume and moisture content of the ASRs. TCLP tests showed that the leachability of arsenic and heavy metals significantly decreased after the treatment. According to the BCR analysis, most of the unstable As, Cd and Cr transformed into a residual fraction. Finally, XRD, SEM, Raman and XPS techniques were carried out to reveal the mechanism. As a result, hydrothermal treatment can efficiently achieve the dehydration, volume reduction and stabilization/solidification of ASRs.

Solid-liquid separation: an emerging issue in heavy metal wastewater treatment

Solid-liquid separation (SLS) plays a dominant role in various chemical industries. Nowadays, low efficiency of SLS also become a significant problem in heavy metal (HM) wastewater treatment, affecting the effluent quality (HM concentration and turbidity) and overall process economy. In this context, we summarize here the occurrence of solids in HM wastewater, as well as typical SLS operations used in HM wastewater treatment, including sedimentation, flotation, and centrifugation. More important, this article reviews the improvement of the SLS operations by some technologies, including coagulation, flocculation, ballasted method, seeding method, granular sludge strategy, and external field enhancement. It is noted that abiological granular sludge strategy and magnetic field enhancement often possess higher SLS efficiency (faster settling velocity or shorter separation time) than other methods. Hence, the two strategies stand out as promising tools for improving SLS in HM wastewater treatment, but further research is required regarding scalability, economy, and reliability.

Removal of ammonia from aqueous solutions by ligand exchange onto a Cu(ii)-loaded chelating resin: kinetics, equilibrium and thermodynamics

A poly ligand exchanger (PLE), Cu(ii)-loaded chelating resin (ammonia adsorption reagent, named AMAR) was prepared to efficiently remove ammonia from solutions by ligand exchange.

Synergistic effects of ion exchange and complexation processes in cysteine-modified clinoptilolite nanoparticles for removal of Cu(ii) from aqueous solutions in batch and continuous flow systems

In this work, clinoptilolite tuff was pre-treated and converted to microparticles (CMP) and nanoparticles (CNP) by a mechanical method.