Properties of iron-based mesoporous silica for the CWPO of phenol: a comparison between impregnation and co-condensation routes

Study on the Performance Test of Fe-Ce-Al/MMT Catalysts with Different Fe/Ce Molar Ratios for Coking Wastewater Treatment

It is very important to choose a suitable method and catalyst to treat coking wastewater. In this study, Fe-Ce-Al/MMT catalysts with different Fe/Ce molar ratios were prepared, characterized by XRD, SEM, and N2 adsorption/desorption, and treated with coking wastewater. The results showed that the optimal Fe-Ce-Al/MMT catalyst with a molar ratio of Fe/Ce of 7/3 has larger interlayer spacing, specific surface area, and pore volume. Based on the composition analysis of real coking wastewater and the study of phenol simulated wastewater, the response surface test of the best catalyst for real coking wastewater was carried out, and the results are as follows: initial pH 3.46, H2O2 dosage 19.02 mL/L, Fe2+ dosage 5475.39 mL/L, reaction temperature 60 °C, and reaction time 248.14 min. Under these conditions, the COD removal rate was 86.23%.

Fine-tuning mesoporous silica properties by a dual-template ratio as TiO2 support for dye photodegradation booster

Titanium dioxide (TiO₂) has been integrated into the surface of mesoporous silica (SMG) synthesized via the hydrothermal approach and a dual template CTAB-Gelatin. XRD, nitrogen adsorption, FTIR, SEM-EDX, and UV-Vis DR spectroscopy were performed to evaluate a 1 wt% TiO₂/SMG material. After titania incorporation, the addition of gelatin during the synthesis of SMG increases the pore volume to 0.76 cc/g. The expansion of the silica pores is caused by the development of TiO₂ crystal grains on the mesoporous silica-gelatin. An increase in the gelatin-CTAB to mesoporous silica weight ratio modifies the surface area, pore size, and particle size without compromising the meso-structure. In this research, the TiO₂/SMG composite demonstrated much greater photodegradability for methylene blue (MB) than the TiO₂/mesoporous silica sample without gelatin. The experimental results indicate that the photocatalytic activity of methylene blue from SMG titania/silica samples is reliant on the adsorption ability of the composite and the photocatalytic activity of titania, with optimal activity from samples with the highest surface area and pore volume, which directly increase the Ti: Si ratio and decrease the photodegradability of the composite when the ratio is too high or too low.

Fe-based Fenton-like catalysts for water treatment: Preparation, characterization and modification

Fenton reaction based on hydroxyl radicals () is effective for environment remediation. Nevertheless, the conventional Fenton reaction has several disadvantages, such as working at acidic pH, producing iron-containing sludge, and the difficulty in catalysts reuse. Fenton-like reaction using solid catalysts rather than Fe²⁺ has received increasing attention. To date, Fe-based catalysts have received increasing attention due to their earth abundance, good biocompatibility, comparatively low toxicity and ready availability, it is necessary to review the current status of Fenton-like catalysts. In this review, the recent advances in Fe-based Fenton-like catalysts were systematically analyzed and summarized. Firstly, the various preparation methods were introduced, including template-free methods (precipitation, sol gel, impregnation, hydrothermal, thermal, and others) and template-based methods (hard-templating method and soft-templating method); then, the characterization techniques for Fe-based catalysts were summarized, such as X-ray diffraction (XRD), Brunauer, Emmett and Teller (BET), SEM (scanning electron microscopy)/TEM (transmission electron microscopy)/HRTEM (high-resolution TEM), FTIR (Fourier transform infrared spectroscopy)/Raman, XPS (X-ray photoelectron spectroscopy), ⁵⁷Fe Mössbauer spectroscopy etc.; thirdly, some important conventional Fe-based catalysts were introduced, including iron oxides and oxyhydroxides, zero-valent iron (ZVI) and iron disulfide and oxychloride; fourthly, the modification strategies of Fe-based catalysts were discussed, such as microstructure controlling, introduction of support materials, construction of core-shell structure and incorporation of new metal-containing component; Finally, concluding remarks were given and the future perspectives for further study were discussed. This review will provide important information to further advance the development and application of Fe-based catalysts for water treatment.

Highly Stable Mn-Doped Metal-Organic Framework Fenton-Like Catalyst for the Removal of Wastewater Organic Pollutants at All Light Levels

A novel Mn-doped Fe-based metal-organic framework (MOF) Fenton-like catalyst was prepared for the removal of wastewater organic pollutants. The catalyst exhibited good degradation performance, stability, and recyclability for the removal of phenol from water with a maximum catalytic efficiency of 96%. Incorporating a long persistent phosphor in the MOF ensured optimum performance in the dark.

Fitting Biochars and Activated Carbons from Residues of the Olive Oil Industry as Supports of Fe- Catalysts for the Heterogeneous Fenton-Like Treatment of Simulated Olive Mill Wastewater

A series of biochars and activated carbons (ACs) was prepared combining carbonization and physical or chemical activation of cheap and abundant residues of the olive oil industry. These materials were used as Fe-support to develop low-cost catalysts for the heterogeneous Fenton-like oxidation of simulated olive mill wastewater (OMW), the highly pollutant effluent generated by this agroindustry. Commercial ACs were also used as reference. All catalysts prepared were extensively characterized and results related with their performances in the catalytic wet peroxide oxidation (CWPO). Results showed a linear relationship of the textural properties of the catalysts with the adsorptive and catalytic performance, as well as the preferential adsorption and degradation of some phenolic compounds (caffeic and gallic acids) by specific interactions with the catalysts’ surface. Despite the best performance of catalysts developed using commercial supports, those prepared from agro-industrial residues present some advantages, including a smaller catalyst deactivation by iron leaching. CWPO results show that catalysts from physically activated olive stones are the most promising materials, reaching total organic carbon and toxicity reductions of 35% and 60%, respectively, as well an efficient use of H₂O₂, comparable with those obtained using commercial supports. This approach showed that the optimized treatment of this type of residues will allow their integration in the circular economic process of the olive oil production.

Scalable construction of heteroatom-doped and hierarchical core–shell MnO2 nanoflakes on mesoporous carbon for high performance supercapacitor devices

Combining interfacial methods and mesoporous carbon channels, an asymmetric device, using N,S-codoped mesoporous carbon and a MnO₂@MC-30 core shell composite, is assembled with high energy, power densities and outstanding cycling stability.

Boosting Fenton-Like Reactions via Single Atom Fe Catalysis

The maximization of the numbers of exposed active sites in supported metal catalysts is important to achieve high reaction activity. In this work, a simple strategy for anchoring single atom Fe on SBA-15 to expose utmost Fe active sites was proposed. Iron salts were introduced into the as-made SBA-15 containing the template and calcined for simultaneous decomposition of the iron precursor and the template, resulting in single atom Fe sites in the nanopores of SBA-15 catalysts (SAFe-SBA). X-ray diffraction (XRD), UV-vis diffuse reflectance spectroscopy (UV-vis DRS), high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), and extended X-ray absorption fine structure (EXAFS) imply the presence of single atom Fe sites. Furthermore, EXAFS analysis suggests the structure of one Fe center with four O atoms, and density functional theory calculations (DFT) simulate this structure. The catalytic performances of SAFe-SBA were evaluated in Fenton-like catalytic oxidation of p-hydroxybenzoic acid (HBA) and phenol. It was found that the single atom SAFe-SBA catalysts displayed superior catalytic activity to aggregated iron sites (AGFe-SBA) in both HBA and phenol degradation, demonstrating the advantage of SAFe-SBA in catalysis.

Removal of pollutants in banknote printing wastewater by mesoporous Fe/SiO2 prepared from rice husk pyrolytic residues

Iron-incorporated silica (Fe/SiO₂) with different Fe/Si molar ratio was successfully prepared from rice husk pyrolytic residues (RHR) through alkali pretreatment, co-precipitation, and calcination. Various characterization methods indicated that the Fe/SiO₂ samples possessed mesoporous structure with Fe species incorporated into the framework of silica. The obtained materials were applied in the treatment of hazardous banknote printing wastewater, and under the optimal conditions, colored pollutants, humic acid-like and soluble microbial by-product-like organics were removed significantly. It was found that Fe/SiO₂ acted as both flocculant and catalyst, and the framework iron species catalyzed the oxidative degradation of refractory organics in the presence of H₂O₂. A heterogeneous Fenton-like system was formed in the wastewater treatment process.

Preparation of Cu-ZSM-5 catalysts by chemical vapour deposition for catalytic wet peroxide oxidation of phenol in a fixed bed reactor

Cu-ZSM-5 catalysts were prepared by chemical vapour deposition for catalytic wet peroxide oxidation (CWPO) of phenol in a fixed bed reactor. Firstly, Cu-ZSM-5 catalysts with Cu loading of 0.5, 2, and 6 wt% were prepared and characterized by X-ray diffraction (XRD), N₂ adsorption-desorption and X-ray photoelectron spectra (XPS). The characterization results demonstrated that CuO was uniformly dispersed on ZSM-5 with slight effect on the structure properties of the support. Then, several variables, such as the copper loading, reaction temperature, catalyst bed height and feed flow rate were investigated in the CWPO of phenol in aqueous solution at high concentration (1000 ppm). Compared with the catalyst prepared by the impregnation method, the Cu-ZSM-5 prepared by chemical vapour deposition has a better capacity of further oxidizing the intermediate organic products into carbon dioxide and water with less metal loading. Based on the Cu-ZSM-5 catalyst with Cu loading of 6 wt%, complete removal of phenol and a high TOC reduction (around 70%) have been achieved at the temperature of 80°C feed flow rate of 2 ml min^-1 and catalyst bed height of 3 cm. Moreover, this catalyst maintained high catalytic activity after three runs with high phenol conversion (94%) under this optimum operating condition. Finally, the reaction mechanism was studied based on the intermediates detected by high-performance liquid chromatography (HPLC).

Stability of BiFeO3 nanoparticles via microwave-assisted hydrothermal synthesis in Fenton-like process

Stable catalysts require high catalytic efficiency and repeated consecutive use, low mass loss, and metal leaching. This study investigated BiFeO₃ (BFO) composite with high stability and reusability using a one step microwave-assisted hydrothermal method (MAHS) to decompose bisphenol A (BPA) used as the target contaminant. After six consecutive reaction cycles in microwave-enhanced Fenton-like process (MW-Fenton-like), the removal rate of BPA decreased from 94 to 87.4% with low metal leaching ratio and mass loss. The morphology, crystal, reaction kinetics, and hydroxyl radical (·OH) were used to demonstrate the high stability of BFO-MAHS. The results indicated that the benign stability and reusability of BFO-MAHS probably occurred because (1) the thermal-effect of MW improved heating rate, which led to the rapid formation stable cube structure and (2) MW mechanical vibrations existed in the preparation process, which further enhanced the cube structure. Therefore, MAHS could be used as a green and environmental friendly method to apply in catalysts synthesis, which could immensely shorten preparation time and enhance the catalytic performance with no waste production.

Chemical vapor deposition of CuO on ZSM-5 membrane for catalytic wet peroxide oxidation of phenol in a fixed bed reactor

Complete removal of phenol and high TOC reduction (around 60%) can be achieved over CuO supported on ZSM-5 membrane.

Synthesis of manganese incorporated hierarchical mesoporous silica nanosphere with fibrous morphology by facile one-pot approach for efficient catalytic ozonation

Manganese incorporated fibrous silica nanosphere (MnOx-0.013/KCC-1) was synthesized by one step hydrothermal method for the first time and its catalytic activity for ozonation of oxalic acid was studied. For comparison, manganese loaded MCM-41 (MnOx-0.013/MCM-41) was prepared by impregnation method. Various characterizations showed that the morphological, structural and textural properties of MnOx-0.013/KCC-1 were well preserved. Ozonation and catalytic ozonation by MnOx-0.013/KCC-1 and MnOx-0.013/MCM-41 led to 4, 85 and 60% reduction in TOC respectively. Furthermore, 0.05 and 1.2mgL(-1) leaching of Mn was detected from MnOx-0.013/KCC-1 and MnOx-0.013/MCM-41, which are approximately 2.0 and 42.0% of the total Mn present in MnOx-0.013/KCC-1 and MnOx-0.013/MCM-41 respectively. The high catalytic activity was attributed to the generation of hydroxyl radical. Surface hydroxyl groups investigated by using phosphates and ATR-FTIR were believed to be the active sites. Our proposed method of synthesis can be generalized for the synthesis of other metal oxides incorporated fibrous silica for environmental catalysis and other catalytic reactions.

Electro-assisted heterogeneous activation of persulfate by Fe/SBA-15 for the degradation of Orange II

The removal of Orange II by activation of persulfate (S2O8(2-), PS) using synthesized Fe/SBA-15 in the electrochemical (EC) enhanced process was reported in this study. The reaction rate constants, degradation mechanism, catalyst stability, and evolution of mineralization and toxicity were detailed investigated. On the basis of radical scavenger results, both the sulfate radicals (SO4(-)) and hydroxyl radicals (OH) were responsible for the degradation of Orange II. A possible pathway is suggested to describe the degradation of Orange II according to the degradation intermediates identified. The results showed that the Fe/SBA-15 catalyst maintained strong reusability and stability with a low level of iron leaching. In addition, favorable mineralization efficiency in terms of COD removal efficiency (75.4%) and TOC removal efficiency (46.3%) was obtained when the reaction time was prolonged to 24h. The toxicity experiments implied that the toxicity of the treated solution ascended at the first 30min but then dropped to almost zero eventually. This study provides a proof-of-concept that can be applied widely for the PS remediation of contaminated water.

Heterogeneous Fenton oxidation of ofloxacin drug by iron alginate support

A new catalytic wet peroxide oxidation of ofloxacin antibiotic is presented in this work. The removal was achieved using a biodegradable sodium alginate-iron material. Several parameters were studied such as iron content, drying duration of the catalytic support, temperature, solid amount and initial drug concentration. The process showed a strong oxidative ability; at optimum conditions, a nearly complete removal of the drug (around 98%) has been reached after three h of treatment. A relatively low decrease of support activity (around 10%) has been observed after three successive oxidation runs and a low iron leaching has been detected (1.2% of the incorporated quantity). The removal of the substrate has been also examined in the absence of hydrogen peroxide in order to discriminate between the contributions of simple adsorption and oxidation processes in the drug disappearance. We also discussed the influence of the studied experimental parameters on the removal kinetic.

Removal of ofloxacin antibiotic using heterogeneous Fenton process over modified alginate beads

The aim of this work is to study the heterogeneous oxidative degradation of ofloxacin antibiotic using a composite material prepared from sodium alginate and cyclohexane dinitrilo tetraacetic acid (CDTA). The characterization tests indicated the successful incorporation of metal chelator and iron. It was also demonstrated that the synthesized beads are mesoporous. The influence of several experimental parameters (i.e.: H2O2 dose, working temperature, beads loading and initial drug concentration) on the process performances was evaluated. The reaction temperature significantly affects the drug conversion efficiency. It was also observed that the synthesized material was efficient toward the target antibiotic degradation in the presence of small quantities of hydrogen peroxide. Under optimum conditions (0.05 g of granules, initial drug concentration=10mg/L, 25μL of 10mmol/L H2O2), conducted in a batch reaction, 94% degradation of ofloxacin was reached. The results also indicate that the composite material showed a reasonable stability; a relatively low decrease of activity after four successive runs (only 9%) and a negligible iron leaching (0.8%) have been observed. The synthesized composite material offered interesting advantages in terms of simplicity, good stability, ease of recovery from the liquid medium after use and its efficiency in the presence of low quantities of oxidant. It constitutes a good candidate in the water treatment area.

Catalytic wet oxidation of phenol with Fe–ZSM-5 catalysts

Systematic study of catalytic wet oxidation of phenol over Fe–ZSM-5 and Fe₂O₃/ZSM-5 catalysts.

Heterogeneous Degradation of Organic Pollutants by Persulfate Activated by CuO-Fe3O4: Mechanism, Stability, and Effects of pH and Bicarbonate Ions

Magnetic CuO-Fe3O4 composite was fabricated by a simple hydrothermal method and characterized as a heterogeneous catalyst for phenol degradation. The effects of pH and bicarbonate ions on catalytic activity were extensively evaluated in view of the practical applications. The results indicated that an increase of solution pH and the presence of bicarbonate ions were beneficial for the removal of phenol in the CuO-Fe3O4 coupled with persulfate (PS) process. Almost 100% mineralization of 0.1 mM phenol can be achieved in 120 min by using 0.3 g/L CuO-Fe3O4 and 5.0 mM PS at pH 11.0 or in the presence of 3.0 mM bicarbonate. The positive effect of bicarbonate ion is probably due to the suppression of copper leaching as well as the formation of Cu(III). The reuse of catalyst at pH0 11.0 and 5.6 showed that the catalyst remains a high level of stability at alkaline condition (e.g., pH0 11.0). On the basis of the characterization of catalyst, the results of metal leaching and EPR studies, it is suggested that phenol is mainly destroyed by the surface-adsorbed radicals and Cu(III) resulting from the reaction between PS and Cu(II) on the catalyst. Taking into account the widespread presence of bicarbonate ions in waste streams, the CuO-Fe3O4/PS system may provide some new insights for contaminant removal from wastewater.

Iron-incorporated mesoporous silica for enhanced adsorption of tetracycline in aqueous solution

The iron-incorporated influenced the adsorption of TC greatly and inner-sphere surface complexes formed between TC and the Fe(iii) on the adsorbent.

Electrochemical enhanced heterogeneous activation of peroxydisulfate by Fe-Co/SBA-15 catalyst for the degradation of Orange II in water

Mesoporous silica SBA-15 supported iron and cobalt catalysts (Fe-Co/SBA-15) were prepared and used in the electrochemical (EC) enhanced heterogeneous activation of peroxydisulfate (PDS, S2O8(2-)) process for the removal of Orange II. The effects of some important reaction parameters such as initial pH, current density, PDS concentration and dosage of Fe-Co/SBA-15 catalysts were investigated. The results showed that the decolorization efficiency was not significantly affected by the initial pH value, and it did increase with the higher PDS concentration, current density and Fe-Co/SBA-15 dosage. Both the sulfate radical (SO4(·-)) and the hydroxyl radical (OH) are considered as the primary reactive oxidants for the Orange II decolorization. The Fe-Co/SBA-15 catalyst maintained its high activity during repeated batch experiments. The intermediate products were identified by GC-MS analysis and a plausible degradation pathway is proposed accordingly. The removal efficiencies of chemical oxygen demand (COD) and total organic carbon (TOC) were 52.1% and 31.9%, respectively after 60 min of reaction time but reached 82.9% and 51.5%, respectively when the reaction time was extended to 24 h. Toxicity tests with activated sludge indicated that the toxicity of the solution increased during the first 30 min and then decreased as the oxidation proceeded.

Ultrasound enhanced heterogeneous activation of peroxymonosulfate by a bimetallic Fe-Co/SBA-15 catalyst for the degradation of Orange II in water

Mesoporous silica SBA-15 supported iron and cobalt (Fe-Co/SBA-15) was prepared and used as catalyst in the ultrasound (US) enhanced heterogeneous activation of peroxymonosulfate (PMS, HSO5(-)) process. The effects of some important reaction parameters on the removal of Orange II by US/Fe-Co/SBA-15/PMS process were investigated. The results indicated that the removal rate of Orange II was not significantly affected by the initial pH, and it increased with the higher PMS concentration, reaction temperature, Fe-Co/SBA-15 dosage and ultrasonic power. Furthermore, sulfate radicals (SO4(-)) were assumed to be the dominating reactive species for the Orange II decolorization. Moreover, the Fe-Co/SBA-15 catalyst showed high activity during the repeated experiments. The intermediate products were identified by GC-MS, thereby a plausible degradation pathway is proposed. In addition, the chemical oxygen demand (COD) removal efficiencies at 2 and 24h were 56.8% and 80.1%, respectively and the corresponding total organic carbon (TOC) removal efficiencies were 33.8 and 53.3%. Finally, toxicity tests with activated sludge showed that the toxicity of the solution increased during the first stage and then decreased significantly with the progress of the oxidation.

Metal nanoparticles as heterogeneous Fenton catalysts

The Fenton reaction (the generation of hydroxyl radicals from hydrogen peroxide) is the most useful method for degradation of organic pollutants in aqueous solution at moderate concentrations. In this Review we summarize the use of metal nanoparticles, either unsupported or deposited on large-surface-area solids, as Fenton catalysts. The Review complements two other reviews in the field of heterogeneous Fenton catalysis using aluminosilicates and carbonaceous materials. Herein, particular emphasis is given to the reaction conditions in which these catalysts are used, highlighting the operating mechanism and the relative efficiency of the materials. Aspects such as leaching of the metal to the solution, reusability, and the concentration of hydrogen peroxide used are analyzed in detail. Besides a critical description of the present status of the field, future trends and the need to establishing valid comparisons to assess the relative efficiencies of the materials are commented on.

Catalytic wet peroxide oxidation of phenol solutions over CuO/CeO2 systems

Three 5% CuO/CeO(2) catalysts were synthesized by sol-gel, precipitation and combustion methods, followed by incipient wetness impregnation with copper nitrate. The samples were characterized by XRD, TPR, BET and tested for the catalytic wet peroxide oxidation of a phenol solution (5 g/L). The reaction took place in a batch reactor at atmospheric pressure, in a temperature range of 60-80°C, during 4h. Phenol conversion, H(2)O(2) consumption, pH and chemical oxygen demand were determined. The reaction temperature and the catalyst loading did improve the phenol and the H(2)O(2) conversions. The effect on the selectivity towards complete mineralization was less marked, with levels among 60-70%. Stepwise addition of H(2)O(2) was also tested.

Degradation of trinitroglycerin (TNG) using zero-valent iron nanoparticles/nanosilica SBA-15 composite (ZVINs/SBA-15)

Trinitroglycerin (TNG) is an industrial chemical mostly known for its clinical use in treating angina and manufacturing dynamite. The wide manufacture and application of TNG has led to contamination of vast areas of soil and water. The present study describes degradation of TNG with zero-valent iron nanoparticles (ZVINs) in water either present alone or stabilized on nanostructured silica SBA-15 (Santa Barbara Amorphous No. 15). The BET surface areas of ZVINs/SBA-15 (275.1 m2 g(-1)), as determined by nitrogen adsorption-desorption isotherms, was much larger than the non-stabilized ZVINs (82.0 m2 g(-1)). X-ray diffraction (XRD) showed that iron in both ZVINs and ZVINs/SBA-15 was present mostly in the α-Fe0 crystalline form considered responsible for TNG degradation. Transmission Electron Microscopy (TEM) showed that iron nanoparticles were well dispersed on the surface of the nanosilica support. Both ZVINs and ZVINs/SBA-15 degraded TNG (100%) in water to eventually produce glycerol and ammonium. The reaction followed pseudo-first-order kinetics and was faster with ZVINs/SBA-15 (k1 0.83 min(-1)) than with ZVINs (k1 0.228 min(-1)). The corresponding surface-area normalized rate constants, knorm, were 0.36 and 0.33 L h(-1) m(-2) for ZVINs/SBA-15 and ZVINs, respectively. The ZVINs/SBA-15 retained its original degradation efficiency of TNG after repeatedly reacting with fresh nitrate ester for five successive cycles. The rapid and efficient transformation of TNG with ZVINs/SBA-15, combined with excellent sustained reactivity, makes the nanometal an ideal choice for the clean up of water contaminated with TNG.