Optimizing adsorption of crystal violet dye from water by magnetic nanocomposite using response surface modeling approach

The effective treatment of dye-containing simulated wastewater by using the cement kiln dust as an industrial waste adsorbent

This study compares the adsorption behavior of both Methylene Blue (MB) and Congo Red (CR) dyes on the surfaces of cement kiln dust (CKD) powder from the experimentally simulated wastewater solution. The cement kiln dust powder was characterized using X-ray Fluorescence (XRF), X-ray diffraction (XRD), N2 adsorption-desorption Brunauer-Emmett-Teller (BET), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscopy (SEM) tests. The adsorption for such dyes was studied under varying mixing contact times, temperatures, and pH as well as various initial concentrations of both dyes and adsorbent using the batch mode experiments. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were applied, and the results revealed that the pseudo-second-order fitted well to the kinetic data. Thermodynamic parameters stated that the adsorption process was endothermic. Studying Linear and nonlinear forms of Langmuir and Freundlich's adsorption isotherms revealed that the adsorption process was followed by both homogeneous mono-layer and heterogeneous multilayer coverage on the active sites of cement kiln dust particles. The data showed that the adsorption capacities of the methylene blue and Congo red dyes were 58.43 and 123.42 mg/g, respectively and cement kiln dust is an adsorbent with little cost for the treatment of wastewater.

Low-cost materials as vehicles for pesticides in aquatic media: a review of the current status of different biosorbents employed, optimization by RSM approach

Water contamination by pesticides is increasing dramatically due to population growth and the extensive use of pesticides in agriculture, leading to grave environmental and health concerns. Thus, efficient processes and the design and development of effective treatment technologies are required due to the enormous demand for fresh water. The adsorption approach has been widely used to remove organic contaminants such as pesticides because of its performance, less expense, high selectivity, and simplicity of operation compared to other treatment technologies. Among alternative adsorbents, biomaterials abundantly available for pesticide sorption from water resources have attracted the attention of researchers worldwide. The main objective of this review article is to (i) present studies on a wide range of raw or chemically modified biomaterials potentially effective in removing pesticides from aqueous media; (ii) indicating the effectiveness of biosorbents as green and low-cost materials for removing pesticides from wastewater; and (iii) furthermore, report the application of response surface methodology (RSM) for modeling and optimizing adsorption.

Functionalization of carbon from rubber fruit shells (Hevea brasiliensis) with silane agents and its application to the adsorption of bi-component mixtures of methylene blue and crystal violet

In this research, activated carbon was obtained from rubber fruit shells (ACRPs). The obtained activated carbon (ACRPs) was modified by magnetite particle coating and silanization with triethoxyiphenylsilane (TEPS) to produce a new magnetic adsorbent (ACRPs-MS). The affinity of as-prepared adsorbent (ACRPs-MS) toward methylene blue (MB) and crystal violet (CV) dyes was tested in mono-component and bi-component solutions. Structural characterization proves the success of the magnetite coating process and the silanization of ACRPs. In the infrared (IR) spectroscopy spectrum of ACRPs-MS, Si-O-Fe and Si-O-Si bonds were identified, which indicated the presence of magnetite and silane. This is also supported by the elemental composition contained in the energy-dispersive X-ray (EDX) diffractogram. In addition, the presence of the porous structure of the surface of the material and the increase in the specific surface area increase the accessibility of contaminants such as MB and CV dyes to be adsorbed to the ACRPs-MS adsorption site effectively. The experimental results showed that the adsorption of mono-component MB and CV dyes by ACRPs-MS was optimum at pH 8 and an interaction time of 60 min. The adsorption kinetics of mono-component MB and CV dyes by ACRPs-MS tended to follow pseudo-second-order kinetics (PSO) models with PSO rate constant (k2) values of 0.198 and 0.993 g mg-1 min-1, respectively. The adsorption of MB and CV dyes by ACRPs-MS in a bi-component mixture tends to follow the Langmuir isotherm model with adsorption capacity (qm) values of 85.060 and 90.504 mg g-1, respectively. Analysis of adsorption data on the bi-component mixture between MB and CV by ACRPs-MS with the Langmuir isotherm equation for a binary mixture resulted in qm of 22.645 × 10-3 mmol equiv g-1. ACRPs-MS material can be used repeatedly five times with adsorption ability > 80%. Desorption of MB and CV dyes was carried out using 0.05 M HCl solution. ACRPs-MS material was able to adsorb MB and CV dyes with a large adsorption capacity and could be used in repeated adsorption. Thus, it can be stated that ACRPs-MS can be used as an effective adsorbent for MB and CV dyes, either singly or in a bi-component mixture.

Salsola Tetragona as a new low-cost adsorbent for water treatment: highly effective adsorption of crystal violet

Synthetic dyes are prevalent in aquatic environments, they have high toxicities, are non-degradable, and accumulate in the water. The removal of Crystal violet (CV) is carried out using batch experiments on the Salsola Tetragona (ST) plant as a novel adsorbent. The prepared adsorbent was analyzed by various methods (MEB, EDX, IRTF and PZC), to support its applicability as adsorbent. The adsorption study of CV is performed by optimizing the parameters affecting the adsorption process. The adsorption kinetics study is represented by pseudo-second-order (R2 = 0.999) and the adsorption process is limited by external mass transport. In addition, the isotherm results demonstrate that the Langmuir model interprets better the adsorption isotherm. The thermodynamic parameters suggest that the adsorption phenomena are spontaneous and exothermic. Furthermore, the adsorption reactions involved are of physisorption type, which facilitates the desorption of pollutants from the surface of the adsorbent. The results show that ST adsorbent effectively removes CV in an aqueous solution, which is demonstrated by the maximum amount adsorption of 246.7 mg.g-1 at optimum adsorption conditions: pH = 6, adsorbent dose of 0.5 g.L-1, initial CV concentration of 10 mg.L-1, and adsorption time of 30 min at 298 K. Finally, these results can be considered as a useful reference for wastewater treatment using ST.

Photocatalytic Degradation of Crystal Violet on Cu, Zn Doped BiVO4 Particles

Fabrication of codoped photocatalysts is a developing area of research. Herein, we explore the visible light photocatalytic properties of Cu, Zn codoped BiVO4 particles. Doping lower valent cations (Cu and Zn) makes the BiVO4 surface more acidic and enables us to target the basic crystal violet (CV) dye. The adopted hydrothermal protocol of synthesis results in the formation of Cu-Zn codoped monoclinic BiVO4 particles. Undoped monoclinic BiVO4, prepared by the same protocol, showed significant formation of oxygen vacancies. XPS analyses confirm the coexistence of Cu2+/Cu+ and Zn2+ dopants. Increased dopant percentage reduced oxygen vacancies. XRD indicates that Cu2+/Cu+ or Zn2+ dopants generally substitute Bi3+ in BiVO4. All photocatalysis activities for CV degradation are reported under near-neutral pH conditions. A typical codoped BiVO4 photocatalyst with 1% Zn and 2% Cu demonstrated the best CV degradation photocatalytic activity. The activity of this Zn, Cu codoped photocatalyst is better than that of pure, Zn-doped, and Cu-doped BiVO4 samples. Active species trapping experiments indicated the possible photocatalysis mechanism. The photocatalysts exhibited appropriate recyclability and photostability.

Mechanistic understanding of green synthesized cerium nanoparticles for the photocatalytic degradation of dyes and antibiotics from aqueous media and antimicrobial efficacy: A review

In recent years, extensive research endeavors are being undertaken for synthesis of an efficient, economic and eco-friendly cerium oxide nanoparticles (CeO2 NPs) using plant extract mediated greener approach. A number of medicinal plants and their specific parts (flowers, bark, seeds, fruits, seeds and leaves) have been found to be capable of synthesizing CeO2 NPs. The specific key phytochemical constituents of plants such as alkaloids, terpenoids, phenolic acids, flavones and tannins can play significant role as a reducing, stabilizing and capping agents in the synthesis of CeO2 NPs from their respective precursor solution of metal ions. The CeO2 NPs are frequently using in diverse fields of science and technology including photocatalytic degradation of dyes, antibiotics as well as antimicrobial applications. In this review, the mechanism behind the green synthesis CeO2 NPs using plant entities are summarized along with discussion of analytical results from characterization techniques. An overview of CeO2 NPs for water remediation application via photocatalytic degradation of dyes and antibiotics are discussed. In addition, the mechanisms of antimicrobial efficacy of CeO2 NPs and current challenges for their sustainable application at large scale in real environmental conditions are discussed.

Compound Similarity Network as a Novel Data Mining Strategy for High-Throughput Investigation of Degradation Pathways of Organic Pollutants in Industrial Wastewater Treatment

Identification of degradation products and pathways is crucial for investigating emerging pollutants and evaluation of wastewater treatment methods. Nontargeted analysis is a powerful tool to comprehensively investigate the degradation pathways of organic pollutants in real-world wastewater samples but often generates large data sets, making it difficult to effectively locate the exact information on interests. Herein, to efficiently establish the linkages among compounds in the same degradation pathways, we introduce a compound similarity network (CSN) as a novel data mining strategy for LC-MS-based nontargeted analysis of complex wastewater samples. Different from molecular networks that cluster compounds based on MS/MS spectra similarity, our CSN strategy harnesses molecular fingerprints to establish linkages among compounds and thus is spectra-independent. The effectiveness of CSN was demonstrated by nontargeted identification of degradation pathways and products of organic pollutants in leather industrial wastewater that underwent laboratory-scale activated carbon adsorption (ACD) and ozonation treatments. Utilizing CSN in interpreting nontargeted data, we tentatively annotated 4324 compounds in the untreated leather industrial wastewater, 3246 after ACD, and 3777 after ACD/ozonation. We located 145 potential degradation pathways of organic pollutants in the ACD/ozonation process using CSN and validated 7 pathways with 15 chemical standards. CSN also revealed 5 clusters of emerging pollutants, from which 3 compounds were selected for in vitro cytotoxicity study to evaluate their potential biohazards as new pollutants. As CSN offers an efficient way to connect massive compounds and to find multiple degradation pathways in a high-throughput manner, we anticipate that it will find wide applications in nontargeted analysis of diverse environmental samples.

Cellulose- supported sulfated-magnetic biocomposite produced from hemp biomass: Effective removal of cationic dyes from aqueous solution

In present study, eco-friendly sulfated cellulose-magnetic biocomposite was successfully synthesized with a simple method from hemp biomass. ATR-FTIR was used to determine chemical changes, while FE-SEM-EDS, STEM, XRD, TG/DTA, and BET techniques were employed to identify changes in morphology, elemental composition, crystal structure, and thermal degradation. Moreover, the saturation magnetization and pHpzc values of the MSHB were also determined. The effectiveness of magnetic sulfated hemp biomass (MSHB) was tested in the removal of cationic dyes from wastewater, including methylene blue (MB), crystal violet (CV), and malachite green oxalate (MGO). The adsorption all three dyes to MSHB, the pseudo-second-order kinetic model and the Langmuir model were determined to be more appropriate, and was endothermic and spontaneous from thermodynamic parameters, too. The maximum MSHB adsorption capacities were found to be 457.6, 509.3, and 1300 mg/g for MB, CV, and MGO at 298 K. With increasing temperature, it also drastically increased in capacity. The outstanding property of the MSHB is that it shows high removal performance wide pH range, even after ten cycles its high removal efficiency is still over 96 % for all three dyes and almost unaffected from dense matrix medium. These results demonstrate that MSHB is remarkable adsorbent for removing cationic dyes.

Insight into the application of supercritical water oxidation for dichlorvos degradation: experimental and simulation aspects

Dichlorvos or 2,2-dichlorovinyl dimethyl phosphate (DDVP) ( C 4 H 7 C l 2 O 4 P ) is a chlorinated organophosphorus pesticide, which is frequently detected in agricultural wastewater. Herein, a batch reactor was used to carry out the supercritical water oxidation (SCWO) of a synthetic wastewater containing dichlorvos as a very hazardous agricultural pollutant. To do so, the impact of four operating parameters including dichlorvos concentration (100-500 ppm), oxidant coefficient (0.7-2), temperature (300-500°C) and time (0-100 s) on dichlorvos removal was optimized by the response surface method (RSM). According to the obtained results, at optimal conditions (i.e. initial concentration of dichlorvos 107.5 ppm, oxidation ratio 1.9234, temperature 419.9°C and time 79.94 s), as an index for dichlorvos removal, the chemical oxygen demand (COD) was found to be about 96.34%. Also, the results of high-performance liquid chromatography test showed that dichloroacetaldehyde (C2CL2H2O) and dichloroacetic acid (C2CL2H2O2) were created as intermediate substances during the dichlorvos degradation. Further, the molecular dynamics simulation was performed using ReaxFF force field to show the reaction path and products obtained in each step of the dichlorvos removal. Finally, as an indication, the simulation results indicated a good coordination with the experimental results.

Statistical Design and Optimization of Cr (VI) Adsorption onto Native and HNO3/NaOH Activated Cedar Sawdust Using AAS and a Response Surface Methodology (RSM)

The removal of heavy metals from wastewater has become the subject of considerable interest at present. Thus, the use of novel adsorbents that are highly efficient is of critical importance for the removal of Cr (VI) ions from aqueous media. The adsorption of Cr (VI) ions from aqueous solutions by a new adsorbent, cedar wood sawdust, and the optimization of its adsorption parameters, were investigated in this study. Cedar wood sawdust was used in its native and HNO3/NaOH chemically modified forms as new low-cost sorbents to remove Cr (VI) ions from aqueous solutions in a batch system. The adsorption conditions were analyzed via response surface methodology. The RSM results showed that the optimal adsorption conditions yielding the best response were an adsorbent mass of 2 g for native Cedar and 1.125 g for its activated form, a metal concentration of 150 mg/L for native Cedar and 250 mg/L for activated, a temperature of 50 °C, a pH of 1, and a contact time of 67.5 min. At optimum adsorption conditions, the maximum adsorption capacities and the adsorption yields were 23.64 mg/g and 84% for native Cedar and 48.31 mg/g and 99% for activated Cedar, respectively.

Valorization of Glucose-Derived Humin as a Low-Cost, Green, Reusable Adsorbent for Dye Removal, and Modeling the Process

Glucose can be isomerized into fructose and dehydrated into key platform biochemicals, following the "bio-refinery concept". However, this process generates black and intractable substances called humin, which possess a polymeric furanic-type structure. In this study, glucose-derived humin (GDH) was obtained by reacting D-glucose with an allylamine catalyst in a deep eutectic solvent medium, followed by a carbonization step. GDH was used as a low-cost, green, and reusable adsorbent for removing cationic methylene blue (MB) dye from water. The morphology of carbonized GDH differs from pristine GDH. The removal efficiencies of MB dye using pristine GDH and carbonized GDH were 52% and 97%, respectively. Temperature measurements indicated an exothermic process following pseudo-first-order kinetics, with adsorption behavior described by the Langmuir isotherm. The optimum parameters were predicted using the response surface methodology and found to be a reaction time of 600 min, an initial dye concentration of 50 ppm, and a GDH weight of 0.11 g with 98.7% desirability. The MB dye removal rate optimized through this model was 96.85%, which was in good agreement with the experimentally obtained value (92.49%). After 10 cycles, the MB removal rate remained above 80%, showcasing the potential for GDH reuse and cost-effective wastewater treatment.

Iron-Iron Oxide Core-Shell Nanochains as High-Performance Adsorbents of Crystal Violet and Congo Red Dyes from Aqueous Solutions

The main aim of this work was to use the iron-iron oxide nanochains (Fe NCs) as adsorbents of the carcinogenic cationic crystal violet (CV) and anionic Congo red (CR) dyes from water. The investigated adsorbent was prepared by a magnetic-field-induced reduction reaction, and it revealed a typical core-shell structure. It was composed of an iron core covered by a thin Fe₃O₄ shell (<4 nm). The adsorption measurements conducted with UV-vis spectroscopy revealed that 15 mg of Fe NCs constituted an efficient dose to be used in the CV and CR treatment. The highest effectiveness of CV and CR removal was found for a contact time of 90 min at pH 7 and 150 min at pH 8, respectively. Kinetic studies indicated that the adsorption followed the pseudo-first-order kinetic model. The adsorption process followed the Temkin model for both dyes taking into account the highest value of the R² coefficient, whereas in the case of CR, the Redlich-Peterson model could be also considered. The maximal adsorption capacity estimated from the Langmuir isotherms for the CV and CR was 778.47 and 348.46 mg g^-1, respectively. Based on the Freundlich model, both dyes adsorbed on the Fe NCs through chemisorption, but Coulombic interactions between the dye and adsorbent cannot be excluded in the case of the CV dye. The obtained results proved that the investigated Fe NCs had an excellent adsorption ability for both dye molecules within five cycles of adsorption/desorption, and therefore, they can be considered as a promising material for water purification and environmental applications.

Sustainable Synthesis of Iron-Zinc Nanocomposites by Azadirachta indica Leaves Extract for RSM-Optimized Sono-Adsorptive Removal of Crystal Violet Dye

Environmental pollution has exacerbated the availability of clean water to mankind. In this study, Azadirachta indica leaf extract was used for sustainable synthesis of Fe-Zn nanocomposites (IZNC). The instrumental techniques of Fourier transformed infrared (FTIR) spectroscopy, energy dispersive X-ray spectroscopy (EDS), and scanning electron microscopy (SEM) were used to determine the structural and chemical composition. The overall surface was mildly acidic in nature, as the pH_PZC was observed to be 6.00. The ultrasonicated adsorption experiments were designed by central composite design (CCD). The best responses, which proposed a contaminants removal of 80.39%, were assessed using the response surface methodology (RSM). By repeating experimental runs at the expected optimum operating parameters (OOP), the method was experimentally affirmed with the %mean error and %RSD₉ being 2.695% and 1.648%, respectively. The interaction of CV dye and the nanocomposite showed tremendous adsorption efficiency towards crystal violet (CV) dye, as revealed by isotherm studies. Fitting kinetics and isotherm models were affirmed by root mean square error (RMSE), χ2, and a Pearson regression coefficient. Thermodynamic studies proved spontaneity of the CV dye adsorption over the nanocomposites. The values for ΔG^o, ΔH^o, and ΔS^o were observed to be -1.089 kJ/mol, 28.59 kJ/mol, and -3.546 kJ/mol, respectively. Recovery of CV dye was carried out in a variety of media, including NaOH, NaCl, and CH₃COOH. The maximum CV recovery was achieved in an acidic media. The robustness of adsorption was affirmed by the interference of various matrix ions, including KCl, LiCl, NaCl, and MgCl₂, which did not significantly affect the adsorption process. The maximum adsorption capacity was obtained at a low concentration of LiCl. The results show that a green synthesis approach for nanocomposite synthesis might be an effective and economical way to remove organic contaminants from wastewater. Moreover, it is also effective for effluent treatment plants (ETP) for waste management purposes, in which it may be coupled with chlorine as a disinfectant to purify water that can be used for domestic and irrigation purposes.

High thiabendazole fungicide uptake using Cellana tramoserica shells modified by copper: characterization, adsorption mechanism, and optimization using CCD-RSM approach

In this paper, Cellana tramoserica (CT) shells were modified by copper and used as an adsorbent to remove thiabendazole (TBZ) from aqueous media. The removal efficiency of TBZ onto CT shells and modified Cellana tramoserica (CT-Cu) shells was investigated by considering the following parameters: initial pesticide concentration, solution pH, agitation time, temperature, and adsorbent mass. The experimental results show that the pseudo-first-order and Langmuir models well describe the adsorption process. The maximum adsorption amount for CT and CT-Cu is 319.68 mg/g and 376.12 mg/g, respectively. CT-Cu showed higher TBZ removal efficiency than CT, explained by the ligand exchange between the water and the pesticide molecules in the metal coordination sphere. Response surface methodology combined with central composite design (RSM-CCD) was used to optimize the adsorption conditions. Optimized values were obtained at 5 for pH, 50 ppm, 120 min, and 20 mg of CT-Cu adsorbent. Under these optimal conditions, 91% of TBZ was removed by adsorption onto CT-Cu. Graphical abstract.

Synthesis of magnetic nanocarbon using palm oil as the green precursor via microwave-assisted arc for wastewater treatment

The presence of metal with microwave irradiation has always invited controversial arguments as the metal will catch on fire easily. But interestingly, researchers found that arc discharge phenomena provide a promising way for molecule cracking to synthesize nanomaterials. This study developed a single-step yet affordable synthesis approach that combines microwave heating and arcing in transforming crude palm oil into magnetic nanocarbon (MNC), which can be considered a new alternative for the palm oil sectors. It involves synthesizing the medium at a partial inert condition with constant coiled stainless steel metal wire (dielectric media) and ferrocene (catalyst). This approach successfully demonstrates heating at a temperature ranging from 190.9 to 472.0 °C with different synthesis times (10-20 min). The produced MNC shows formations of spheres with average sizes of 20.38-31.04 nm, mesoporous structure (SBET: 14.83-151.95 m²/g), and high content of fixed carbon (52.79-71.24wt%), and the ratio of the D and G bands (I_D/I_G) is 0.98-0.99. The formation of new peaks in the FTIR spectra (522.29-588.48 cm^-1) supports the appearance of the FeO compounds from the ferrocene. The magnetometer shows high magnetization saturation (22.32-26.84 emu/g) in ferromagnetic materials. The application of the MNC in wastewater treatment has been demonstrated by evaluating their adsorbent capability with Methylene Blue (MB) adsorption test at a different concentrations varying between 5 and 20 ppm. The MNC produced at synthesis time (20 min) shows the highest adsorption efficiency (10.36 mg/g) compared to others, with 87.79% removal of MB dye. As a result, the value for Langmuir is not promising compared to Freundlich, with R² being around 0.80, 0.98, and 0.99 for MNC synthesized at 10 min (MNC10), 15 min (MNC15), and 20 min (MNC20), respectively. Hence, the adsorption system is in a heterogeneous condition. The microwave-assisted arcing thereby presents a promising approach to transforming CPO into MNC that could remove the hazardous dye.

Simultaneous removal of cationic and anionic dyes from simulated industrial effluents using a nature-inspired adsorbent

Alginate-grafted polyaniline (Alg-g-PANI) microparticles were synthesized through the grafting of aniline onto functionalized Alg followed by double crosslinking by glutaraldehyde and calcium chloride. The performance of the developed microparticles as adsorbent in simultaneous removal of malachite green (MG) and congo red (CR) dyes were examined by the batch method. Experimental parameters, including adsorbent amount, pH, initial dyes concentrations, and contact time were optimized. Langmuir and Freundlich adsorption models were employed to explore the equilibrium isotherm. As the Langmuir model results, the maximum adsorption capacities (Q_m) of microparticles for the MG and CR dyes were obtained as 578.3 and 409.6 mgg^-1, respectively. Adsorption kinetics for both dyes were well-fitted with the pseudo-second-order model that confirm the rate-limiting step might be the chemical adsorption. The adsorbent was regenerated via desorption process and was reusable five times without a substantial decrease in its adsorption efficacy in first three cycles. Adsorbent-dyes interactions were computationally evaluated using Gromacs package, and it was found that both MG and CR are able to interact strongly with the adsorbent. In accordance with experimental results, simulation data revealed that MG can be removed more efficiently than those of the CR. As the experimental results, we could conclude that the synthesized Alg-g-PANI microparticles can be used as a nature-inspired adsorbent for simultaneous removals of CR and MG dyes.

Value Coefficient of Polyethylene Fiber Soil Embankment Slope Based on Response Surface Analysis

The utilization of polymers can strengthen soil, but at a high price. In this study, value coefficients were proposed to evaluate the cost-effectiveness of fiber-reinforced roadbeds, and the effects of embankment-slope-influencing factors on the value coefficients were analyzed by response surface methodology. Ultrahigh-molecular-weight polyethylene fiber (UPEF) was used as the reinforcement material for soil. First, the shear strength parameters of fiber soil with different fiber diameters were obtained from the direct shear tests to set the parameters of the finite element models. Second, three factors, namely filling height, slope angle, and fiber diameter, were selected as input parameters based on the Box–Behnken Design (BBD) experimental design method, and their effects on the value coefficient of the fiber soil embankment slope were investigated. Finally, the design parameters at the maximum value coefficient of the fiber soil embankment slope were determined based on the results of the response surface analysis. The results indicated that the addition of UPEF could effectively improve the cohesion of the soil; the interaction between the filling height and fiber diameter is most obvious. The optimization of design parameters based on the value coefficient of the fiber soil slope is a slope-engineering design method considering comprehensive benefits.

Cadmium exposure in population: alcoholic beverage consumption and health risk assessment

Risk assessment of cadmium (Cd) for human health play a key role because of toxic effect. Researchers are undergoing constant development for modelling approaches to make a risk assessment. It was carried out a central composite design combining with response surface modeling to optimize and modeling of Cd2+ ions in this study. Also, this study was performed to provide information about possible risk associated with alcoholic beverage consumption. Some independent process parameters including contact time and pH were chosen for optimization. Under optimal parameters, 142.9 mg g-1 was determined as Cd2+ ions removal effectiveness. Significance independent parameters and their interactions were checked using analysis of variance. These results were verified by correlation coefficients (R2 = 0.9967) of the statistical prediction. Estimated daily intake (EDI) and target hazard quotients (THQ) were calculated, to assess health risk. The Cd2+ ions EDI values (µg/day/person) were less than the recommended dietary allowance values and also, its THQ value was less than 1, also. When the obtained results compared with the levels set by regulatory authorities, the studied alcoholic beverages consumption do not pose a toxicological risk.

Graphical abstract

Activated Carbon/ZnFe2O4 Nanocomposite Adsorbent for Efficient Removal of Crystal Violet Cationic Dye from Aqueous Solutions

The aim of this study was to investigate the potential advantage of ZnFe₂O₄-incorporated activated carbon (ZFAC), fabricated via a simple wet homogenization, on the removal of cationic dye crystal violet (CV) from its aqueous solutions. The as-prepared ZFAC nanocomposite was characterized using Fourier transform infrared (FTIR), X-ray diffraction (XRD), nitrogen adsorption, scanning electron microscope (SEM), thermogravimetric analysis (TGA), and ultraviolet-visible (UV-Vis). Batch adsorption operating conditions such as the pH (3-11), CV concentration (25-200 ppm), ZFAC dose (10-50 mg), temperature (23-45 °C), and contact time were evaluated. The results indicate pH-dependent uptake (optimum at pH 7.2) increased with temperature and CV concentration increase and decreased as adsorbent dose increased. Modeling of experimental data revealed better fit to the Langmuir than Freundlich and Temkin isotherms, with maximum monolayer capacities (Q_m) of 208.29, 234.03, and 246.19 mg/g at 23, 35, and 45 °C, respectively. Kinetic studies suggest pseudo-second order; however, the intra-particle diffusion model indicates a rate-limiting step controlled by film diffusion mechanism. Based on the thermodynamic parameters, the sorption is spontaneous (-ΔG°), endothermic (+ΔH°), and random process (+ΔS°), and their values support the physical adsorption mechanism. In addition to the ease of preparation, the results confirm the potential of ZFAC as a purifier for dye removal from polluted water.

Facile Synthesis of Sustainable Tannin/Sodium Alginate Composite Hydrogel Beads for Efficient Removal of Methylene Blue

To meet the requirement of sustainable development, bio-based adsorbents were developed for the removal of dye contaminant. To improve the adsorption capacity of pure sodium alginate (SA) adsorbent for the removal of methylene blue (MB), aromatic bio-based tannin (Tan) was incorporated through the cross-linking with calcium ion. The obtained Tan/SA composite hydrogel beads were characterized with SEM, FTIR and TG, demonstrating that millimeter-sized beads were obtained through calcium cross-linking with enhanced thermal stability. The maximum capacity (247.2 mg/g) at optimal condition (pH = 12, T = 45 °C) was obtained for the 40%Tan/SA adsorbents, with a removal efficiency of 82.4%. This can be ascribed to the electrostatic attraction between SA and MB, as well as the formation of π–π stacking between Tan and MB. The adsorption process for MB is endothermic, and chemical adsorption, the removal efficiency was exceeded 90% after five cycles.

An enhanced method for the removal of methyl violet dye using magnetite nanoparticles as an adsorbent: Isotherm, kinetic and thermodynamic study

A green method has been developed using Gilloy (Tinospora Cordifolia) shoot extract to synthesize magnetic nanoparticles (MNPs). A further modification of MNPs was performed using anionic surfactant sodium dodecyl sulphate (SDS), to remove cationic dye methyl violet (MV) efficiently from the solution. As an adsorbent, SDS modified MNPs (SDS-MNPs) were tested for their ability to remove MV dye. Synthesized MNPs were characterized by ultra violet-visible spectroscopy (UV-VIS), X-ray diffraction spectroscopy (XRD), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). In batch adsorption experiments, the effect of adsorbent dosage, initial dye concentration, time, and pH was evaluated. The maximum adsorption capacity of the adsorbent for MV dye was found to be 174.2 mg g^-1. The adsorption of dye onto the adsorbent followed Langmuir's isotherm. It was shown that the adsorption kinetics of dyes obeyed pseudo-second-order kinetics. Using thermodynamic parameters, spontaneous and exothermic adsorption was determined. As synthesized nanoparticles are magnetic in nature, regeneration and reusability of MNPs were investigated.

Treatment of methyldiethanolamine wastewater using subcritical and supercritical water oxidation: parameters study, process optimization and degradation mechanism

In this examination, sub/supercritical water oxidation (SCWO) in a batch reactor was employed to degrade methyldiethanolamine (MDEA). To do so, the impact of different operating parameters including temperature (300-500 °C), time (0-100 s), initial MDEA concentration (1000-4000 ppm), oxidant coefficient (0.7-2), and pH (7.3-9.5) on MDEA degradation was separately and together investigated. Subsequently, the response surface method (RSM) was applied to optimize the operating condition of MDEA degradation. Based on the obtained results, a maximum amount of 97.4% MDEA degradation was achieved at the initial MDEA concentration of 1095 ppm in optimal condition (i.e., oxidant coefficient: 1.913, temperature: 472 °C and residence time: about 17 s). Furthermore, according to the HPLC analysis, there was a negligible amounts of formic acid (CH₂O₂) and nitrous acid (HNO₂) in the solution at the end of MDEA removal experiment. Eventually, the mechanism of MDEA degradation was acquired using molecular dynamics simulation (MDS), which had an acceptable coordination with the experimental results. In this way, the MDS results revealed that the presence of CH₂O₂ and HNO₂ compounds in the products was related to the degradation of MDEA and their production as by-products during the SCWO experiments.

Efficient Removal of Methylene Blue by Bio-Based Sodium Alginate/Lignin Composite Hydrogel Beads

Dye pollution is a serious issue in current environment protection, and bio-based adsorbents have been receiving much attention in wastewater treatment, due to their low cost, renewable, and environmentally friendly characteristics. Bio-based sodium alginate/lignin composite (SA/Lig) hydrogel beads were fabricated by a facile cross-linking with calcium ion and used for the removal of methylene blue (MB). The obtained SA/Lig microbeads were characterized with SEM, FTIR, and TG, and the effect of lignin content, pH, and temperature on the MB adsorption was investigated. The results indicated that the introduction of aromatic lignin can not only enhance thermal stability but also can improve the adsorption performance. Under optimal conditions, the maximum adsorption capacity (254.3 mg/g) was obtained for the SA/Lig-20% beads, with a removal efficiency of 84.8%. The adsorption process for MB is endothermic, and the rate-limiting step is chemical adsorption. The removal efficiency is higher than 90% after five cycles, revealing that the prepared beads show good regeneration ability.

Synergistic sorption performance of karaya gum crosslink poly(acrylamide-co-acrylonitrile) @ metal nanoparticle for organic pollutants

In this work, we tailor facile hydrogels nanocomposite (HNC) based on sustainable karaya gum for water treatment. Karaya gum crosslink poly(acrylamide-co-acrylonitrile) @ silver nanoparticle (KG-cl-P(AAm-co-AN)@AgNPs) HNC were made by an aqueous free radical in situ crosslink copolymerization of acrylamide (AAm) and acrylic acid (AA) in aqueous solution of KG-stabilized AgNPs. FTIR, XRD, DTA-TGA, SEM, and TEM were used to characterize HNC. The hydrogels' swelling, diffusion, and network characteristics were investigated. The removal efficiency of HNC was found to be 99% at pH 8 for a crystal violet (CV), dose of 0.02 g after 1 h. Dye adsorption by these hydrogels was also investigated in terms of isotherms, and kinetics. The dye's exceptionally high adsorption capacity on HNC for CV removal is explained by H-bonding interactions, as well as dipole-dipole and electrostatic interactions between anionic adsorbent and cationic dye molecules (Qmax, 1000 mg/g). The HNC can be regenerated with 0.1 M HCl and reused at least 10 times maintaining over 68% dye removal. The loading of AgNPs into the polymeric matrix of KG-cl-P(AAm-co-AN) significantly increases the removal percentage of CV dye from its aqueous solution, according to this study.

Efficient Removal of Dyes from Aqueous Solution by Adsorption on L-Arginine-Modified Mesoporous Silica Nanoparticles

The use of mesoporous silica modified with L-arginine (Ar-MSNPs) for the removal of ionic dyes from aqueous solutions has been investigated. Several analytical techniques have been used to determine the characteristics of nanoadsorbents. The removal of crystal violet and fluorescein was performed using the batch method to investigate the effects of cultivation pH, initial concentrations of dyes, and exposure time on adsorption efficiency. The optimum adsorption of fluorescein was achieved at pH 2, whereas the optimum adsorption of crystal violet was achieved at pH 13. The equilibrium was established in both systems at 20 min at low concentrations, and approximately 30 min at high concentrations. The equilibrium adsorption data was analyzed using Langmuir and Freundlich isotherm models. The correlation coefficient (R2) values of the isotherms presented the best fit with the Langmuir isotherm. The adsorption kinetic data was fitted with the pseudo second-order model for both systems.

Fabrication and prospective applications of graphene oxide-modified nanocomposites for wastewater remediation

Water bodies have become polluted with heavy metals and hazardous contaminants as a result of fast development. Many strategies have been devised by researchers in order to remove hazardous contaminants from the aquatic environment. Utilizing graphene oxide-based composite materials as efficient adsorbents for waste water treatment, desalination, separation, and purification is gaining attraction nowadays. Some of their defining properties are high mechanical strength, hydrophilicity, remarkable flexibility, ease of synthesis, atomic thickness, and compatibility with other materials. In water treatment, high separation performance and stable graphene-based laminar structures have been the main goals. Magnetic separation is among the methods which received a lot of attention from researchers since it has been shown to be quite effective at removing harmful pollutants from aqueous solution. Graphene oxide-modified nanocomposites have provided optimal performance in water purification. This review article focusses on the fabrication of GO, rGO and MGO nanocomposites as well as the primary characterization tools needed to assess the physiochemical and structural properties of graphene-based nanocomposites. It also discusses the approaches for exploiting graphene oxide (GO), reduced graphene (rGO), and magnetic graphene oxide (MGO) to eliminate contaminants for long-term purification of water. The potential research hurdles for using fabricated MGOs as an adsorbent to remediate water contaminants like hazardous metals, radioactive metal ions, pigments, dyes, and agricultural pollutants are also highlighted.

Synthesis and chacterization of graphene-based materials (GO, rGO, and MGO) by FT-IR, XRD, UV-VIS, SEM, and Raman spectroscopy, and their potential applications for wastewater treatment.

Ultrasonic-assisted synthesis of zeolite/activated carbon@MnO2 composite as a novel adsorbent for treatment of wastewater containing methylene blue and brilliant blue

In this study, zeolite/activated carbon@MnO₂ composite was used as a novel adsorbent to eliminate methylene blue (MB) and brilliant blue (BB) dyes from aqueous media. To this end, activated carbon (AC) was produced by Ziziphus Spina-Christi leaves and then used to synthesize zeolite/AC@MnO₂ composite. Various analyses such as BET, SEM, EDX, Map, FTIR, and XRD were performed to determine the surface features of the above composite. BET analysis indicated that the aforementioned composite has a mesoporous structure. Also, the best conditions for the adsorption of MB and BB dyes were obtained at pH of 9 and 2, temperature of 25 °C, adsorbent dosage of 1 and 2 g/L, initial dye concentration of 10 mg/L, and contact time of 40 and 60 min, respectively. Under optimal conditions, the utmost removal efficiency of MB and BB dyes using the zeolite/AC@MnO₂ composite was 98.43% and 96.54%, respectively, indicating significant adsorption efficiencies. Moreover, the utmost adsorption capacity of MB and BB dyes was 67.56 and 66.22 mg/g, respectively. Furthermore, intraparticle and film diffusion mechanisms were very important in the adsorption process. Besides, thermodynamic and equilibrium studies indicated that the adsorption process is exothermic, physical, and spontaneous. Generally, the aforementioned composite has a significant adsorption capacity and can be a suitable adsorbent to eliminate cationic dyes from industrial effluents.

Optimization of Synergistic Leaching of Valuable Metals from Spent Lithium-Ion Batteries by the Sulfuric Acid-Malonic Acid System Using Response Surface Methodology

A new environmentally friendly and economical recycling process for extracting metals from spent lithium-ion batteries (LIBs) using sulfuric acid and malonic acid as leaching agents is proposed. By applying Box-Behnken design (BBD) and response surface methodology (RSM) optimization techniques, the global optimal solution of the maximum leaching rate of metals in spent LIBs is realized. The results show that under the optimal conditions of 0.93 M H₂SO₄, 0.85 M malonic acid, and a liquid/solid ratio of 61 g·L^-1, a temperature of 70 °C and 5 vol % of 30% H₂O₂, 99.79% Li, 99.46% Ni, 97.24% Co, and 96.88% Mn are recovered within 81 min. The error between the theoretical value and the actual value of the metal leaching rate predicted by the regression model is less than 1.0%. Additionally, the study of leaching kinetics reveals that the leaching process of Li, Ni, Co, and Mn in spent cathode materials was affected by the synergistic effect of interfacial mass transfer and solid product layer diffusion. Economic analysis reveals that evaluation index should be fully considered when formulating recovery processes for different metals. This process can reduce the environmental risks of heavy metal disposal and allow the reuse of metals recovered from spent LIBs.

Removal of Nickel Ions from Aqueous Solutions by 2-Hydroxyethyl Acrylate/Itaconic Acid Hydrogels Optimized with Response Surface Methodology

The adsorption of Ni²⁺ ions from water solutions by using hydrogels based on 2-hydroxyethyl acrylate (HEA) and itaconic acid (IA) was studied. Hydrogel synthesis was optimized with response surface methodology (RSM). The hydrogel with the best adsorption capacity towards Ni²⁺ ions was chosen for further experiments. The hydrogel was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and atomic force microscopy (AFM) analysis before and after the adsorption of Ni²⁺ ions. Batch equilibrium experiments were conducted to investigate the influence of solution pH, hydrogel weight, ionic strength, adsorption time, temperature and initial concentration of nickel ions on the adsorption. Time-dependent adsorption fitted the best to the pseudo-second-order kinetic model. A thermodynamic study revealed that the adsorption was an exothermic and non-spontaneous process. Five isotherm models were studied, and the best fit was obtained with the Redlich-Peterson model. Consecutive adsorption/desorption studies indicated that the HEA/IA hydrogel can be efficiently used as a sorbent for the removal of Ni²⁺ ions from the water solution. This study develops a potential adsorbent for the effective removal of trace nickel ions.

Electrochemical Degradation of Crystal Violet Using Ti/Pt/SnO2 Electrode

Today, organic wastes (paints, pigments, etc.) are considered to be a major concern for the pollution of aqueous environments. Therefore, it is essential to find new methods to solve this problem. This research was conducted to study the use of electrochemical processes to remove organic pollutants (e.g., crystal violet (CV)) from aqueous solutions. The galvanostatic electrolysis of CV by the use of Ti/Pt/SnO2 anode, were conducted in an electrochemical cell with 100 mL of solution using Na2SO4 and NaCl as supporting electrolyte, the effect of the important electrochemical parameters: current density (20–60 mA cm−2), CV concentration (10–50 mg L−1), sodium chloride concentration (0.01–0.1 g L−1) and initial pH (2 to 10) on the efficiency of the electrochemical process was evaluated and optimized. The electrochemical treatment process of CV was monitored by the UV-visible spectrometry and the chemical oxygen demand (COD). After only 120 min, in a 0.01 mol L−1 NaCl solution with a current density of 50 mA cm−2 and a pH value of 7 containing 10 mg L−1 CV, the CV removal efficiency can reach 100%, the COD removal efficiency is up to 80%. The process can therefore be considered as a suitable process for removing CV from coloured wastewater in the textile industries.

Core-Shell Structured Magnetic Carboxymethyl Cellulose-Based Hydrogel Nanosorbents for Effective Adsorption of Methylene Blue from Aqueous Solution

This article reports effective removal of methylene blue (MB) dyes from aqueous solutions using a novel magnetic polymer nanocomposite. The core-shell structured nanosorbents was fabricated via coating Fe₃O₄ nanoparticles with a layer of hydrogel material, that synthesized by carboxymethyl cellulose cross-linked with poly(acrylic acid-co-acrylamide). Some physico-chemical properties of the nanosorbents were characterized by various testing methods. The nanosorbent could be easily separated from aqueous solutions by an external magnetic field and the mass fraction of outer hydrogel shell was 20.3 wt%. The adsorption performance was investigated as the effects of solution pH, adsorbent content, initial dye concentration, and contact time. The maximum adsorption capacity was obtained at neutral pH of 7 with a sorbent dose of 1.5 g L⁻¹. The experimental data of MB adsorption were fit to Langmuir isotherm model and Pseudo-second-order kinetic model with maximum adsorption of 34.3 mg g⁻¹. XPS technique was applied to study the mechanism of adsorption, electrostatic attraction and physically adsorption may control the adsorption behavior of the composite nanosorbents. In addition, a good reusability of 83.5% MB recovering with adsorption capacity decreasing by 16.5% over five cycles of sorption/desorption was observed.

Sorptive removal of methylene blue from water by magnetic multi-walled carbon nanotube composites

In the present study, five magnetic multi-walled carbon nanotubes (MMWCNTs) with different diameters were prepared and their performance on the sorptive removal of methylene blue (MB) from water was investigated. Transmission electron microscope, scanning electron microscope, Fourier transform infrared spectrometer, X-ray diffraction, and vibrating sample magnetometer confirm that the surface of these MMWCNTs has been decorated by Fe₃O₄ nanoparticles, which renders the MMWCNTs superparamagnetic. Thus, these MMWCNTs can be easily separated from water after the adsorption. During the adsorption process, pH slightly affected the removal efficiency of MB and the adsorption performed better under weak alkaline conditions. Adsorption kinetics followed the pseudo-second-order kinetic model well, and the Dubinin-Radushkevich model fitted the isotherms best. The maximum adsorption capacity for MB reached 204.2 mg/g, and the values decreased with increasing diameters of MMWCNTs due to decreasing specific surface areas. The thermodynamics parameters indicated the spontaneous and exothermic nature of the adsorption. The reusability test showed that MMWCNTs could be used for 6 cycles without significant loss of the adsorption capacity. And common ions (K⁺, Na⁺, Ca²⁺ and Al³⁺) and SDS in water did not show greatly effects on the removal efficiency of MB. Hence, MMWCNTs prepared in this study could be promising adsorbents for dyes removal from wastewater.

Barium/Cobalt@Polyethylene Glycol Nanocomposites for Dye Removal from Aqueous Solutions

Dyes are known as one of the most dangerous industrial pollutants which can cause skin diseases, allergy, and provoke cancer and mutation in humans. Therefore, one of the important environmental issues is the effective removal of dyes from industrial wastewater. In the current work, BaFe₁₂O₁₉/CoFe₂O₄@polyethylene glycol (abbreviated as BFO/CFO@PEG) nanocomposite was synthesized and evaluated regarding its capacity for adsorptive removal of a model dye Acid Blue 92 (denoted as AB92) from aqueous solutions. The characteristics of the prepared nanocomposite was determined by tests such as X-ray diffraction (XRD), scanning electron microscope (SEM), vibration sample magnetization (VSM), and Fourier transform infrared spectroscopy (FTIR). The effects of conditional parameters including pH (2–12), initial concentration of dye (20–100 mg/L), adsorbent dosage (0.02–0.1 g/L) and contact time (0-180 min) on the adsorption of dye were investigated and then optimized. The results indicated that with the increase of the adsorbent dosage from 0.02 to 0.1 g/L, the removal efficiency increased from 74.1% to 78.6%, and the adsorbed amount decreased from 148.25 to 31.44 mg/g. The maximum removal efficiency (77.54%) and adsorption capacity (31.02 mg/g) were observed at pH 2. Therefore, the general optimization conditions revealed that the maximum adsorption efficiency of dye was obtained in condition of initial concentration of 20 mg/L, contact time of 1 h and pH of solution equal 2. The adsorption isotherm and kinetic data were evaluated using a series of models. The pseudo-second order kinetic model and Freundlich isotherm model show the best fitting with experimental data with R²∼0.999.

Effective Removal of Crystal Violet Dye Using Neoteric Magnetic Nanostructures Based on Functionalized Poly(Benzofuran-co-Arylacetic Acid): Investigation of the Adsorption Behaviour and Reusability

Synthetic dyes represent a significant class of contaminants released in the environment. Crystal violet is a triarylmethane dye used in several fields such as printing inks, the textile or paper industries, as well as in cell histology. Coating magnetic nanoparticles with functionalized polymers has been proved to improve their efficiency, offering unique properties for applications in wastewater treatment. The current paper focuses on preparing and characterising magnetic core-shell nanoparticles coated with poly(benzofuran-co-arylacetic acid) functionalized with folic acid as an organic shell. The new polymer-based magnetic nanostructures were applied for crystal violet extraction from aqueous solutions. The nanostructures were structurally and morphologically investigated by Fourier-transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). While thermal and magnetic properties of the magnetic nanostructures were determined by thermogravimetric analysis (TGA) and magnetization measurements (VSM). At the same time, crystal violet concentrations were determined by UV-VIS spectroscopy. The influence of initial dye concentration and contact time on the removal efficiency has been studied to achieve the optimum adsorption conditions. The dye adsorbent neoteric magnetic nanostructure was easily desorbed and reused, the adsorption capacity decreasing from 100% to 97.63% in the first five cycles, reaching a minimum of 88.74% after the 10th recycling step.

Highly Efficient Methylene Blue Dye Removal by Nickel Molybdate Nanosorbent

Removing methylene blue (MB) dye from aqueous solutions was examined by the use of nickel molybdate (α-NiMoO₄) as an adsorbent produced by an uncomplicated, rapid, and cost-effective method. Different results were produced by varying different parameters such as the pH, the adsorbent dose, the temperature, the contact time, and the initial dye concentration. Adsorbent dose and pH had a major removal effect on MB. Interestingly, a lower amount of adsorbent dose caused greater MB removal. The amount of removal gained was efficient and reached a 99% level with an initial methylene blue solution concentration of ≤160 ppm at pH 11. The kinetic studies indicated that the pseudo-second-order kinetic model relates very well with that of the obtained experimental results. The thermodynamic studies showed that removing the MB dye was favorable, spontaneous, and endothermic. Impressively, the highest quantity of removal amount of MB dye was 16,863 mg/g, as shown by the Langmuir model. The thermal regeneration tests revealed that the efficiency of removing MB (11,608 mg/g) was retained following three continuous rounds of recycled adsorbents. Adsorption of MB onto α-NiMoO₄ nanoparticles and its regeneration were confirmed by Fourier transform infrared spectroscopy (FTIR) analysis and scanning electron microscopy (SEM) analysis. The results indicated that α-NiMoO₄ nanosorbent is an outstanding and strong candidate that can be used for removing the maximum capacity of MB dye in wastewater.

Potential of the magnetic hollow sphere nanocomposite (graphene oxide-gadolinium oxide) for arsenic removal from real field water and antimicrobial applications

Potential of the magnetic hollow-sphere nanocomposite, graphene oxide-gadolinium oxide (GO-Gd₂O₃) for arsenic (As) removal from real field water with developing a continuous operating system and antimicrobial activity were investigated. The characterization results suggest that the prepared GO-Gd₂O₃ is a hallow sphere wool-like nanocomposite having 50.91 m² g^-1 surface area. The sorption studies revealed that a high adsorption capacity (216.70 mg g^-1) can be achieved using GO-Gd₂O₃ (0.1 g L^-1) at a pH of 6.0, and temperature of 293 K. The main and novel observations from the loading of Gd₂O₃ are that the GO adsorption efficiency, adsorbent separation rate from aqueous solutions, and the stability of the composite have been altered. Thus, the developed material can overcome the separation and stability issues associated with the bare GO, and exhibits an enhanced adsorption capacity toward arsenic was higher or comparable with existing magnetic material. In addition, the developed adsorption method was well applied for real field water samples collected from the mining area of South Korea where the GO-Gd₂O₃ can reduce the quantity of arsenic under the maximum accepted concentration of arsenic considered fit for drinking water stipulated by environmental protection agencies. Furthermore, the GO-Gd₂O₃ nanocomposite shows a high bacterial photocatalytic inactivation and was comparable with other reports.

Dendrimer-modified magnetic nanoparticles as a sorbent in dispersive micro-solid phase extraction for preconcentration of metribuzin in a water sample

This study was conducted to synthesize magnetic nanoparticles (MNPs) modified with generation 5 (G₅) polyamidoamine (PAMAM) dendrimer and apply them as a sorbent in the dispersive-micro-solid phase extraction (D-μ-SPE) method for preconcentration of metribuzin in water samples. The characterization of synthesized nanoparticles was performed by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), dynamic light scattering (DLS), and vibrating sample magnetometry (VSM). The effects of sample solution pH, the terminal group type, dendrimer generation, ionic strength, sorbent dosage, and desorption conditions on the removal efficiency were investigated. The linear range was calculated from 25-1000 μg L^-1 and the LOD was 10 μg L^-1. The recovery percentages for the spiked real samples ranged from 95.3% to 103.5% and relative standard deviations (RSD%) were in the range of 87.2-92.1 and 4.2 to 6.3 (n = 5) respectively. Applying the method developed in this work in water samples revealed good extraction recoveries with a RSD of 5.6-7.3%.

Application of geopolymers synthesized from incinerated municipal solid waste ashes for the removal of cationic dye from water

In this study, municipal solid waste bottom ash (MSW-BA) and fly ash (MSW-FA) were used as a source of aluminosilicate to prepare geopolymer (GEO) adsorbents (GEO-MSWBA and GEO-MSWFA) for the removal of methylene blue (MB) from water. The effects of temperature, pH, and initial concentration on the MB adsorption onto GEO-MSWBA and GEO-MSWFA were evaluated. The adsorption isotherms parameters and thermodynamics were also determined. Detailed physical and chemical characterizations of the prepared adsorbents were carried out to further understand their impact on MB adsorption. The results from the scanning electron microscopy revealed a uniform granule-sphere like structure on both prepared geopolymers, which would facilitate the MB adsorption onto the adsorbents. The X-ray diffraction allowed observation of the microstructural transformations that occur after the alkaline activation. The surface areas of the GEO-MSWBA and the GEO-MSWFA were recorded as 32.78 m²/g and 4.5 m²/g, respectively. From the Fourier transform infrared, a stretching vibration of the aluminosilicate tetrahedral was observed, which indicated the success of geopolymerization. The prepared geopolymers showed a high capability of MB adsorption from an aqueous solution. The adsorption process was best suited and explained using the Langmuir isotherm model with a maximum adsorption capacity of 666.7 mg/g for the GEO-MSWBA (at 25°C) and 769.2 mg/g for the GEO-MSWFA (at 35°C). The positive value of the enthalpy (ΔH^o) for the GEO-MSWBA suggested the reaction favored endothermic reaction while the negative value of entropy (ΔS^o) indicated a solid/liquid random interaction. On the other hand, the negative ΔH^o value for the GEO-MSWFA indicated the reaction followed an exothermic reaction causing energy to be released, the positive ΔS^o value indicated a good affinity at the solid-liquid surface. The overall negative value for Gibbs free energy (ΔG^o) for both adsorbents suggested the adsorption was spontaneous and feasible. It was also inferred that n- π interaction, direct and indirect hydrogen bond, and electrostatic interaction between the MB and the prepared geopolymers facilitated the adsorption process. The current study shows that the GEO-MSWBA and the GEO-MSWFA have a great potential of removing MB as a cationic dye from water without performing any sort of laborious pretreatments.

Novel cobalt-carbon@silica adsorbent

Recently, carbon nanostructures are of high importance due to their unique characteristics and interesting applications. Pyrolysis of anthracene with cobalt complex Co(2,2'-bipy)Cl2 (1), where (2,2'-bipy) is 2,2'-bipyridine, in the absence and presence of silica gave in high yield cobalt-carbon nanocomposite CoCNC (2) and CoCNC@SiO2 (3) at 600 °C and 850 °C, respectively. They were characterized using SEM, TEM, PXRD, Raman and XPS. (3) and (2) contain core-shell cobalt(0)/cobalt oxide-graphite with or without silica support. PXRD indicates that (2) contains crystalline hexagonal α-Co and cubic β-Co phases while (3) contains only cubic β-Co phase and silica. The structure of (2) is 3D hierarchical carbon architecture wrapping spherical and elliptical cobalt nanoparticles. (3) consists of graphitized structures around cobalt nanoparticles embedded in the silica matrix. XPS reveals that the nanocomposites contain oxygen functional groups that enhance uptake of cationic dyes. CoCNC@SiO2 (3) has higher capacity and thus is better adsorbent of Basic Violet 3 than CoCNC (2). The Langmuir adsorption capacity of (3) is 19.4 mg g-1 while column capacity is 12.55 mg g-1 at 25 °C. Freundlich isotherm and pseudo-second-order kinetic models fit well the adsorption data. Thermodynamics indicate that adsorption(3) is exothermic. Column regeneration was tested for three cycles and Yan et al. was found the best kinetic model.

Preparation of a Three-Dimensional Porous Graphene Oxide-Kaolinite-Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Because of the widespread presence of antibiotics in water, soil, and other environments, they pose great potential risks to the environment, threatening human and animal health. In this study, graphene oxide-kaolinite homogeneous dispersion was prepared by simple liquid phase exfoliation. The three-dimensional (3D) porous graphene oxide-kaolinite-poly(vinyl alcohol) composites were prepared by the cross-linking of poly(vinyl alcohol) and the formation of ice crystals during the freezing-drying process. Three influencing factors [adsorbent dosage, ciprofloxacin (CIP) initial concentration, and time] of CIP adsorption and removal were systematically analyzed by the response surface method. The order of significance for response values (CIP removal rate) was adsorbent dosage > CIP initial concentration > time. The 3D porous material showed good adsorption capacity of CIP, the theoretical maximum adsorption capacity was 408.16 mg/g, and it had good recyclability. By Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy analysis, it was found the composite adsorbs CIP by hydrogen bonding and π-π interaction. In conclusion, the graphene oxide-kaolinite-poly(vinyl alcohol) porous composite is a good candidate for efficient antibiotic wastewater treatment.

Green synthesis of Zn0.5Ni0.5AlFeO4 magnetic nanoparticles and investigation of their photocatalytic activity for degradation of reactive blue 21 dye

This paper focuses on the successful synthesis of Zn_0.5Ni_0.5AlFeO₄ magnetic nanoparticles applying tragacanth gel through the sol-gel technique, as an environmentally-friendly, economical and simple method for the first time. The prepared magnetic nanoparticles were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDX), and vibrating sample magnetometer (VSM). Based on the XRD result, the conformation of single phase cubic spinel structure with the average crystallite size of 10 nm was confirmed. The VSM result exhibited that the nanoparticles have the saturation magnetization of 33.82 emu/g and coercive field of 56 Oe. The organic dye degradation of reactive blue 21 (RB21) was specified utilizing the synthesized magnetic nanoparticles under visible light irradiation. The toxicity of the by-products derived from dye degradation was studied using phytotoxicity test and total organic carbon (TOC) analysis. The photocatalytic activity of the catalyst was measured with changing factors including photocatalyst dosage, initial dye concentration, pH, and contact time. The results presented that Zn_0.5Ni_0.5AlFeO₄ MNPs could degrade 94% of the reactive blue 21.