Simultaneous adsorption and reduction of U(VI) on reduced graphene oxide-supported nanoscale zerovalent iron

Green preparation of regenerable biohybrids with xanthan gum-stabilized biogenic mackinawite nanoparticles for efficient treatment from high-concentration uranium wastewater

The high efficiency, economy, sustainability and no secondary pollution of U(VI) removal is an important and challenging topic for U(VI) wastewater treatment. Here, the regenerable biohybrids with xanthan gum (XG) stabilized biogenic mackinawite nanoparticles (BX-FeS) were prepared, where XG acted as carrier facilitated the Fe2+ attachment and induced the low size, high stability and activity of nearly spherical FeS nanoparticles. Results showed that BX-FeS kept high activity after storing two years and good performance for U(VI) removal in broad pH range and co-existence of ions, and had greater removal efficiency (97.9 %) than biogenic B-FeS (67.1 %). Moreover, BX-FeS preformed high adsorption capacity in uranium wastewater (658.0 mg/g), and lower cost compared with zerovalent-iron and silica gel. Importantly, BX-FeS maintained high activity within three regeneration cycles driven by Desulfovibrio desulfuricans, inhibited the secondary pollution (Fe3+, SO42-) of reaction. This study provides a new strategy for sustainable and efficient treatment of U(VI) wastewater.

Selective Adsorption of Sr(II) from Aqueous Solution by Na3FePO4CO3: Experimental and DFT Studies

The efficient segregation of radioactive nuclides from low-level radioactive liquid waste (LLRW) is paramount for nuclear emergency protocols and waste minimization. Here, we synthesized Na3FePO4CO3 (NFPC) via a one-pot hydrothermal method and applied it for the first time to the selective separation of Sr2+ from simulated LLRW. Static adsorption experimental results indicated that the distribution coefficient Kd remained above 5000 mL·g-1, even when the concentration of interfering ions was more than 40 times that of Sr2+. Furthermore, the removal efficiency of Sr2+ showed no significant change within the pH range of 4 to 9. The adsorption of Sr2+ fitted the pseudo-second-order kinetic model and the Langmuir isotherm model, with an equilibrium time of 36 min and a maximum adsorption capacity of 99.6 mg·g-1. Notably, the adsorption capacity was observed to increment marginally with an elevation in temperature. Characterization analyses and density functional theory (DFT) calculations elucidated the adsorption mechanism, demonstrating that Sr2+ initially engaged in an ion exchange reaction with Na+. Subsequently, Sr2+ coordinated with four oxygen atoms on the NFPC (100) facet, establishing a robust Sr-O bond via orbital hybridization.

Effects of Fe(II) and humic acid on U(VI) mobilization onto oxidized carbon nanofibers derived from the pyrolysis of bacterial cellulose

The effects of Fe(II) and humic acid on U(VI) immobilization onto oxidized carbon nanofibers (Ox-CNFs, pyrolysis of bacterial cellulose) were investigated by batch, spectroscopic and modeling techniques, with results suggesting that, Ox-CNFs exhibited fast adsorption rate (adsorption equilibrium within 3 h), high adsorption performance (maximum adsorption capacity of 208.4 mg/g), good recyclability (no notable change after five regenerations) in the presence of Fe(II) towards U(VI) from aqueous solutions (e.g., 40 % reduction and 10 % adsorption at pH 8.0), which was attributed to the various oxygen-containing functional groups, excellent chemical stability, large specific surface area and high redox effect. U(VI) adsorption increased with increasing pH from 2.0 to 5.0, then high-level plateau and remarkable decrease were observed at 5.0-6.0 and at pH > 6.0, respectively. According to FT-IR and XPS analysis, a negative correlation between U(VI) reduction and organic in the presence of Fe(II) implied that U(VI) reduction was driven by Fe(II) while inhibited by humic acid. The interaction mechanism of U(VI) on Ox-CNFs was demonstrated to be adsorption and ion exchange at low pH and reduction at high pH according to XPS and surface complexation modeling. These findings filled the knowledge gaps pertaining to the effect of Fe(II) on the transformation and fate of U(VI) in the actual environment. This carbon material with distinctive performance and unique topology offers a potential platform for actual application in environmental remediation.

Tuning active sites on biochars for remediation of mercury-contaminated soil: A comprehensive review

Mercury (Hg) contamination is acknowledged as a global issue and has generated concerns globally due to its toxicity and persistence. Tunable surface-active sites (SASs) are one of the key features of efficient BCs for Hg remediation, and detailed documentation of their interactions with metal ions in soil medium is essential to support the applications of functionalized BC for Hg remediation. Although a specific active site exhibits identical behavior during the adsorption process, a systematic documentation of their syntheses and interactions with various metal ions in soil medium is crucial to promote the applications of functionalized biochars in Hg remediation. Hence, we summarized the BC's impact on Hg mobility in soils and discussed the potential mechanisms and role of various SASs of BC for Hg remediation, including oxygen-, nitrogen-, sulfur-, and X (chlorine, bromine, iodine)- functional groups (FGs), surface area, pores and pH. The review also categorized synthesis routes to introduce oxygen, nitrogen, and sulfur to BC surfaces to enhance their Hg adsorptive properties. Last but not the least, the direct mechanisms (e.g., Hg- BC binding) and indirect mechanisms (i.e., BC has a significant impact on the cycling of sulfur and thus the Hg-soil binding) that can be used to explain the adverse effects of BC on plants and microorganisms, as well as other related consequences and risk reduction strategies were highlighted. The future perspective will focus on functional BC for multiple heavy metal remediation and other potential applications; hence, future work should focus on designing intelligent/artificial BC for multiple purposes.

Effects of incorporating Mn into goethite on adsorption of dissolved organic matter and potentially toxic elements in soil: Isotherms, kinetics, and mechanisms

Goethite is ubiquitous in the environment and plays key role in preserving dissolved organic matter (DOM) and deactivating potentially toxic elements (PTEs) by adsorbing DOM and PTEs. Various non-Fe metals are usually incorporated into natural goethite, substituting Fe in the goethite structure, which dramatically influence the physico-chemical properties and adsorption behavior of the goethite. In the present study, adsorption of DOM and Pb(II) on Mn-substituted goethite samples was investigated. The results displayed that the specific surface area (SSA) of mineral samples increased by 67.6% as the incorporation of Mn for Fe, from 25.71 m2 g-1 for pure goethite to 43.09 m2 g-1for Mn-goethite. Besides, the Mn substitution caused more hydroxyl groups and relatively fewer positive charges on mineral surface, and Mn in the Mn-goethite samples was predominantly present as Mn(III). The amount of DOM adsorbed to per unit mass of goethite was increased as Mn content increased, which was attributed to Mn incorporation increasing the SSA of mineral samples. However, the SSA-normalized absorption capacity for goethite to DOM was decreased by Mn because Mn substitution decreased the number of positive charges of mineral samples, which weakened the electrostatic attraction between DOM and the minerals. The amount of Pb(II) adsorbed to per unit mass of goethite was increased by Mn substitution, and the amount of Pb(II) adsorbed to per unit SSA of goethite increased as the amount of Mn substitution increased, indicating that the increased capacity for adsorbing Pb was not only caused by the SSA increasing but also by there were more surface hydroxyl groups on the Mn-goethite than pure goethite and Pb(II) preferentially adsorbed to Mn sites on the Mn-goethite. The present study results showed that Mn-goethite could be used to sequester DOM and remediate soil contaminated with PTEs because Mn-goethite has a high adsorption capacity and is environmentally benign.

GO accelerate iron oxides formation and tetrabromobisphenol A removal enhancement in the GO loaded NZVI system

Tetrabromobisphenol A (TBBPA) is an emerging persistent organic pollutant, which is very difficult to remove by common methods. In this study, the GO-load nanoscale zero-valent iron (NZVI/GO) was fabricated and optimized to improve the reaction rate and removal efficiency for TBBPA reliably and efficiently. The results showed that GO-load significantly reduced the self-aggregation of NZVI and the aggregate size decreased by 50.00% (1400-700 nm). Meanwhile, GO significantly improved the reaction rate k_obs (1.11 ± 0.11 h^-1) of TBBPA in the NZVI/GO system compared to the NZVI (0.40 ± 0.08 h^-1) system, and this increment was more pronounced (177.5%) when the mass ratio of NZVI-to-GO reached 1.0 than other mass ratios. Furthermore, X-Ray Diffraction and X-ray photoelectron spectroscopy analysis suggested that the Fe²⁺ transformation was changed and enriched by the GO. Only magnetite (Fe₃O₄) was detected on the surface of NZVI, whereas the maghemite (γ-Fe₂O₃), hematite (α-Fe₂O₃), and Fe₃O₄ were detected on the interface of NZVI/GO, which further performed the complexation adsorption through the -OH of TBBPA. This specific complexation adsorption is another potential accelerated removal mechanism for TBBPA and intermediates within the NZVI/GO system. This research has put forward a new perspective for widening the application of TBBPA removal using the synergistic effect between GO and NZVI.

Systematic and Bibliometric Analysis of Magnetite Nanoparticles and Their Applications in (Biomedical) Research

Recent reports show air pollutant magnetite nanoparticles (MNPs) in the brains of people with Alzheimer's disease (AD). Considering various field applications of MNPs because of developments in nanotechnology, the aim of this study is to identify major trends and data gaps in research on magnetite to allow for relevant environmental and health risk assessment. Herein, a bibliometric and systematic analysis of the published magnetite literature (n = 31 567) between 1990 to 2020 is completed. Following appraisal, publications (n = 244) are grouped into four time periods with the main research theme identified for each as 1990-1997 "oxides," 1998-2005 "ferric oxide," 2006-2013 "pathology," and 2014-2020 "animal model." Magnetite formation and catalytic activity dominate the first two time periods, with the last two focusing on the exploitation of nanoparticle engineering. Japan and China have the highest number of citations for articles published. Longitudinal analysis indicates that magnetite research for the past 30 years shifted from environmental and industrial applications, to biomedical and its potential toxic effects. Therefore, whilst this study presents the research profile of different countries, the development in research on MNPs, it also reveals that further studies on the effects of MNPs on human health is much needed.

XPS and NMR analyze the combined forms of Pb in Cladophora rupestris subcells and its detoxification

In this study, the combined forms of Pb in Cladophora rupestris (L.) (C. rupestris) were investigated via X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonance (NMR), different Pb concentrations (0, 0.5, and 5.0 mg/L), and C. rupestris subcells were explored. Results showed that combined forms of Pb mainly account for Pb-polysaccharides (Pb-OH of carbohydrates) in the cell wall, Pb-protein (Pb-N= and (C-N-)₂Pb) in the organelle, and Pb-organic acid (Pb-sulfates, (CO)₂-Pb and (COO)₂-Pb) in the soluble fraction. Pb-S-containing group (Pb-C-S) could formed in subcelluar when C. rupestris was subjected to high Pb stress. Meanwhile, Pb²⁺ could penetrate the C. rupestris cells via the formed chelate between GSH/MT and -OH functional groups. Results could help understand the role of subcellular fraction in the algae remediation and detoxification to heavy metal.

Experimental study on in situ remediation of Cr(VI) contaminated groundwater by sulfidated micron zero valent iron stabilized with xanthan gum

Micron zero valent iron (mZVI) was an underground remediation material, which had great application potential to replace nano zero valent iron (nZVI) from the perspective of economic and health benefits. However, mZVI was highly prone to gravitational settling, which limited its wide application for in situ remediation of contaminated groundwater. This paper was devoted to develop an efficient and economical groundwater remediation material based on mZVI, which should possess excellent stability, reactivity, and transportability. Thereby xanthan gum (XG) stabilized and Na₂S₂O₄ sulfidated mZVI (XG-S-mZVI) was synthesized and characterized with SEM, XRD, XPS, and FTIR techniques. In terms of stability, the adsorbed XG and the dispersed XG worked together to resist the sedimentation of S-mZVI. In terms of reactivity, sulfidation enhanced the electron transfer rate and electron selectivity of XG-S-mZVI, thereby improved the reactivity of XG-S-mZVI. The hexavalent chromium (Cr(VI)) removal rate constant by XG-S-mZVI was determined to be 832.4 times than bare mZVI. In terms of transportability, the transportability of XG-S-mZVI was greatly improved (~80 cm in coarse sand and ~50 cm in medium sand). Straining was the main mechanism of XG-S-mZVI retention in porous media. XG-S-mZVI in situ reactive zone (XG-S-mZVI-IRZ) was only suitable to the media with a grain size larger than 0.25 mm. This study could provide theoretical support and guidance for the implementation of IRZ technology based on mZVI.

GO-SWCNT Buckypapers as an Enhanced Technology for Water Decontamination from Lead

Water decontamination is an important challenge resulting from the incorrect disposal of heavy metal waste into the environment. Among the different available techniques (e.g., filtration, coagulation, precipitation, and ion-exchange), adsorption is considered the cheapest and most effective procedure for the removal of water pollutants. In the last years, several materials have been tested for the removal of heavy metals from water, including metal-organic frameworks (MOFs), single-walled carbon nanotubes (SWCNTs), and graphene oxide (GO). Nevertheless, their powder consistency, which makes the recovery and reuse after adsorption difficult, is the main drawback for these materials. More recently, SWCNT buckypapers (SWCNT BPs) have been proposed as self-standing porous membranes for filtration and adsorption processes. In this paper, the adsorption capacity and selectivity of Pb²⁺ (both from neat solutions and in the presence of other interferents) by SWCNT BPs were evaluated as a function of the increasing amount of GO used in their preparation (GO-SWCNT buckypapers). The highest adsorption capacity, 479 ± 25 mg g⁻¹, achieved for GO-SWCNT buckypapers with 75 wt.% of graphene oxide confirmed the effective application of such materials for cheap and fast water decontamination from lead.

Efficient removal of pefloxacin from aqueous solution by acid-alkali modified sludge-based biochar: adsorption kinetics, isotherm, thermodynamics, and mechanism

In this paper, one kind of acid-alkali modified sludge-based biochar (ASBC) was synthesized, characterized, and employed as adsorbent for the removal of pefloxacin. The characterization results showed that the specific surface area (SSA) of ASBC (53.381 m²/g) was significantly higher than that of SBC (24.411 m²/g). ASBC had a rougher surface, larger particle distribution, lower zero point charge, and richer functional groups (e.g., C-O and O-H) than SBC. The adsorption capacity of ASBC was 1.82 times than that of SBC. After 8 adsorption cycles in reuse experiment, the adsorption capacity of ASBC for pefloxacin still reached 144.08 mg/L, indicating that ASBC has good reusability. Static experiments showed that the optimal pH value was 6.0 in the adsorption of pefloxacin on SBC and ASBC. The result of adsorption kinetics indicated that the pseudo-second-order model could describe well the adsorption process. The Freundlich model was better than the Langmuir model to describe the adsorption of pefloxacin by ASBC, indicating that the adsorption process was mainly multilayer adsorption. Thermodynamic result showed that the adsorption of pefloxacin by ASBC was spontaneous and endothermic. The removal mechanism of pefloxacin by ASBC is mainly the substitution reaction and π-π EDA interaction. In summary, acid-alkali modified biochar is an effective adsorbent for pefloxacin in aqueous solution, and has great application prospects.

Mechanism-Enhanced Active Attapulgite-Supported Nanoscale Zero-Valent Iron for Efficient Removal of Pb2+ from Aqueous Solution

In this study, attapulgite-supported nano zero-valent iron (nZVI@ATP) was synthesized by a liquid-phase reduction method using active attapulgite (ATP) as raw material, and used for Pb2+ remediation in aqueous solution. To understand the mechanism of Pb2+ removal, various techniques were used to characterize nZVI@ATP. The results showed that spherical nZVI particles were uniformly dispersed on the surface of ATP, and the agglomeration of nZVI particles was significantly weakened. The adsorption performance of nZVI@ATP for Pb2+ was greatly improved compared with that of ATP ore, in which the Fe/ATP mass ratio of 1:2 was the best loading ratio. Under the conditions of a temperature of 25 °C and a pH of 5.00, the initial concentration of Pb2+ was 700 mg/L, and the Pb2+ removal rate of nZVI@ATP was 84.47%. The adsorption of nZVI@ATP to Pb2+ was mainly a spontaneous endothermic reaction of heterogeneous surfaces, and the adsorption rate of nZVI@ATP to Pb2+ was proportional to pH in the range of 2–5.5. The presence of Na+, Mg2+, and Ca2+ can inhibit the removal of Pb2+, and Ca2+ has the strongest inhibition effect on the removal of Pb2+. The removal mechanism of Pb2+ by nZVI@ATP obtained from SEM-EDS, BET, XRD, FTIR and XPS included reduction, precipitation, and the formation of complexes.

A poly(amidoxime)-modified MOF macroporous membrane for high-efficient uranium extraction from seawater

Although metal–organic frameworks (MOFs) own excellent uranium adsorption capacity but are still difficult to conveniently extract uranium from seawater due to the discrete powder state. In this study, a new MOF-based macroporous membrane has been explored, which can high-efficiently extract uranium through continuously filtering seawater. Through modifying the UiO-66 with poly(amidoxime) (PAO), it can disperse well in a N,N-dimethylformamide solution of graphene oxide and cotton fibers. Then, the as-prepared super-hydrophilic MOF-based macroporous membrane can be fabricated after simple suction filtration. Compared with nonmodified MOFs, this UiO-66@PAO can be dispersed uniformly in the membrane because it can stabilize well in the solution, which have largely enhanced uranium adsorbing capacity owing to the modified PAO. Last but not least, different from powder MOFs, this UiO-66@PAO membrane provides the convenient and continuously uranium adsorbing process. As a consequence, the uranium extraction capacity of this membrane can reach 579 mg·g−1 in 32 ppm U-added simulated seawater for only 24 h. Most importantly, this UiO-66@PAO membrane (100 mg) can remove 80.6% uranyl ions from 5 L seawater after 50 filtering cycles. This study provides a universal method to design and fabricate a new MOF-based adsorbent for high-efficient uranium recovery from seawater.

U(VI) adsorption by green and facilely modified Ficus microcarpa aerial roots: Behavior and mechanism investigation

Uranium (U)-containing wastewater poses serious pressure to human health and environmental safety. The treatment of U-bearing wastewater using green and facilely fabricated materials is considered a promising alternative. Herein, the raw and modified aerial roots of Ficus microcarpa (RARF and MARF, respectively) were prepared and applied to the treatment of synthesized U-containing wastewater. The results showed that the adsorption process was spontaneous and chemically controlled, which was in good accordance with the pseudo-second-order kinetic and the Redlich-Peterson isotherm adsorption model. The adsorption mechanisms were proposed to be the complexation between U(VI) and oxygen/phosphorus-containing functional groups on MARF.

Facile preparation of magnetic porous biochars from tea waste for the removal of tetracycline from aqueous solutions: Effect of pyrolysis temperature

Pyrolysis process significantly influences the physicochemical properties and potential application of magnetic porous biochars (MPBCs). However, the effects of pyrolysis temperature on the properties of MPBCs as well as substantial adsorption are still unclear. This study reported a facile method to obtain the MPBC from tea waste via pyrolysis of a mixture of hydrochar, KHCO₃, and FeCl₃·6H₂O under different temperatures (500-800 °C), and explored further the adsorption toward tetracycline (TC). Results showed pyrolysis temperature obviously influenced the physicochemical properties of MPBCs, and MPBC pyrolyzed at 700 °C (MPBC-700) has a highest specific surface area (1066 m² g^-1) and pore volume (2.693 cm³ g^-1). However, the adsorption potential increased consistently from 59.35 mg g^-1 for MPBC-500 to 333.22 mg g^-1 for MPBC-800, suggesting that the surface area and pore volume were not the only factors determining TC adsorption. Further analysis showed that the pore-filling, π-π interaction, complexation, and hydrogen bonding contributed together to TC adsorption. Moreover, all MPBCs possessed a high saturation magnetization, indicating the easy separation by an external magnet. Therefore, MPBCs (especially at 700 °C) can act as the excellent adsorbents for contaminant removal due to their high separation, adsorption, and reuse performance.

Long-Term Exposure and Effects of rGO-nZVI Nanohybrids and Their Parent Nanomaterials on Wastewater-Nitrifying Microbial Communities

Single nanomaterials and nanohybrids (NHs) can inhibit microbial processes in wastewater treatment, especially nitrification. While existing studies focus on short-term and acute exposures of single nanomaterials on wastewater microbial community growth and function, long-term, low-exposure, and emerging NHs need to be examined. These NHs have distinctly different physicochemical properties than their parent nanomaterials and, therefore, may exert previously unknown effects onto wastewater microbial communities. This study systematically investigated long-term [∼6 solid residence time [(SRT)] exposure effects of a widely used carbon-metal NH (rGO-nZVI = 1:2 and 1:0.2, mass ratio) and compared these effects to their single-parent nanomaterials (i.e., rGO and nZVI) in nitrifying sequencing batch reactors. nZVI and NH-dosed reactors showed relatively unaffected microbial communities compared to control, whereas rGO showed a significantly different (p = 0.022) and less diverse community. nZVI promoted a diverse community and significantly higher (p < 0.05) biomass growth under steady-state conditions. While long-term chronic exposure (10 mg·L^-1) of single nanomaterials and NHs had limited impact on long-term nutrient recovery, functionally, the reactors dosed with higher iron content, that is, nZVI and rGO-nZVI (1:2), promoted faster NH₄⁺-N removal due to higher biomass growth and upregulation of amoA genes at the transcript level, respectively. The transmission electron microscopy images and scanning electron microscopy─energy-dispersive X-ray spectroscopy analysis revealed high incorporation of iron in nZVI-dosed biomass, which promoted higher cellular growth and a diverse community. Overall, this study shows that NHs have unique effects on microbial community growth and function that cannot be predicted from parent materials alone.

Two dimensional MXenes as emerging paradigm for adsorptive removal of toxic metallic pollutants from wastewater

Effective methods for removing harmful metals from wastewater have had a huge impact on reducing freshwater scarcity. Because of its excellent removal effectiveness, simplicity and low cost at ambient conditions, adsorption is one of the most promising purifying approaches. MXene-based nanoarchitectures have proven to be effective adsorbents in a variety of harmful metal removal applications. This owes from the distinctive features such as, hydrophilicity, high surface area, electron-richness, great adsorption capacity, and activated metallic hydroxide sites of MXenes. Given the rapid advancement in the design and synthesis of MXene nanoarchitectures for water treatment, prompt updates on this research area are needed that focus on removal of toxic metal, such as production routes and characterization techniques for the advantages, merits and limitations of MXenes for toxic metal adsorption. This is in addition to the fundamentals and the adsorption mechanism tailored by the shape and composition of MXene based on some representative paradigms. Finally, the limits of MXenes are highlighted, as well as their potential future research directions for wastewater treatment. This manuscript may initiate researchers to improve unique MXene-based nanostructures with distinct compositions, shapes, and physiochemical merits for effective removal of toxic metals from wastewater.

Development of artificial neural networks software for arsenic adsorption from an aqueous environment

Arsenic contamination is a global problem, as it affects the health of millions of people. For this study, data-driven artificial neural network (ANN) software was developed to predict and validate the removal of As(V) from an aqueous solution using graphene oxide (GO) under various experimental conditions. A reliable model for wastewater treatment is essential in order to predict its overall performance and to provide an idea of how to control its operation. This model considered the adsorption process parameters (initial concentration, adsorbent dosage, pH, and residence time) as the input variables and arsenic removal as the only output. The ANN model predicted the adsorption efficiency with high accuracy for both training and testing datasets, when compared with the available response surface methodology (RSM) model. Based on the best model synaptic weights, user-friendly ANN software was created to predict and analyze arsenic removal as a function of adsorption process parameters. We developed various graphical user interfaces (GUI) for easy use of the developed model. Thus, a researcher can efficiently operate the software without an understanding of programming or artificial neural networks. Sensitivity analysis and quantitative estimation were carried out to study the function of adsorption process parameter variables on As(V) removal efficiency, using the GUI of the model. The model prediction shows that the adsorbent dosages, initial concentration, and pH are the most influential parameters. The efficiency was increased as the adsorbent dosages increased, decreasing with initial concentration and pH. The result show that the pH 2.0-5.0 is optimal for adsorbent efficiency (%).

Green Synthesis of Nanostructure CeO2 Using Tea Extract: Characterization and Adsorption of Dye from Aqueous Phase

Nanostructure CeO₂ powders were synthesized using tea waste extract as gel precursor. The as-prepared samples were characterized by thermogravimetric analyzer (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Based on the TGA/DTG analysis, the intermediates of cerium chloride hydrates (CeCl₃.4H₂O and CeCl₃.H₂O) and cerium anhydrous (CeCl₃) were produced, and the formation temperature of CeO₂ was estimated to be 773 K. The cubic fluorite structure of CeO₂ was detected to be the predominant species and was completely formed at the calcination temperature of 773K–1073 K with a crystal size between 8.8 and 11.4 nm based on the XRD measurement. Moreover, the main chemical state of ceria on the surface of the synthesized samples was confirmed to be tetravalent ceria by XPS. All samples show a strong Raman signal at a well-defined chemical shift of 463 cm⁻¹ and a significant symmetry feature was observed, suggesting that the tetravalent ceria is the dominant species throughout the bulk sample. All the synthesized CeO₂ calcined at different temperatures showed higher adsorption efficiency for Congo red (CR) compared with commercial CeO₂. The adsorption efficiency maintained a steady state of more than 95% when the concentration of CR and adsorption temperature were varied in this study. The kinetic analysis showed that the second-order model was the appropriate model to interpret the adsorption behavior of synthesized CeO₂. The calculated adsorption capacity derived from the second-order model is in good agreement with the experimental data. The isotherm analysis revealed that the Freundlich and D-R models fit well for the synthesized CeO₂ and represent physisorption with a multilayer mechanism. The thermodynamic parameters, including the changes in Gibb's free energy, enthalpy, and entropy, suggested that the adsorption of CR on the synthesized CeO₂ sample was a spontaneous and endothermic process.

Hydrothermally synthesized titanate nanomaterials for the removal of heavy metals and radionuclides from water: A review

Hazardous heavy metals and radionuclides in water and wastewater are of drastic concern owing to their detrimental impacts on the organisms as well as the circumambient ecosystem. To remove them as much as we can, both technique and materials were studied in the past years. The adsorption technique as superior water remediation method with the simplicity of design, environmental friendliness and high efficiency was well established. Consequently, it is practically important to explore advanced and economically feasible absorbents for removing these poisonous pollutants from aqueous solutions. So far, large numbers of experiments proved hydrothermally synthesized titanate nanomaterials (TNMs) could be a prospectively excellent adsorbent extracting heavy metals and radionuclides from water due to the high specific surface area, tunable pore size, abundant surface active sites, favorable hydrophilic properties. The objective of this work is to give an overview of hydrothermal synthesis, adsorption performance of TNMs for heavy metals and radionuclides, as well as the various influencing factors for water purification. It comprehensively reviews the structural changes and regenerability of TNMs after adsorption, and different modification methods adopted for improving removal capacity. Additionally, it uniquely highlights the efficient decontamination of the pollutants through a synergistic effect of adsorption and photocatalysis by TNMs. This review provides detailed information for the development, application, and research challenges faced by hydrothermally synthesized TNMs for the removal of heavy metals and radionuclides from aqueous solutions, which will serve as a reference guide for scientists in related fields.

Mechanism of efficient remediation of U(VI) using biogenic CMC-FeS complex produced by sulfate-reducing bacteria

Uranium in groundwater during uranium mining activities urgently needs to be remediated through effective and environmental-friendly approaches. The reduction and immobilization of soluble U(VI) using biogenic carboxymethyl cellulose modified iron sulfide complex (biogenic CMC-FeS complex) is one of the emerging and innovative methods. However, its removal mechanism is largely unknown. Here, biogenic CMC-FeS complex with extracellular polymeric substances (EPS) and CMC was successfully synthesized by sulfate-reducing bacteria (SRB) and showed highly dispersible capacity. The tryptophan and tyrosine, which were the main components in EPS produced by SRB on CMC-FeS surface, significantly increased the U(VI) removal capacity of the biogenic CMC-FeS complex compared with chemically synthesized CMC-FeS. U(VI) removal was attributed to the adsorption of soluble U(VI) by ≡FeO⁺, CMC, tryptophan, and tyrosine on the biogenic CMC-FeS complex, following its reduction by S^2-, S₂^2- and Fe²⁺. Moreover, biogenic CMC-FeS complex with CMC-to-FeS molar ratio of 0.0005 performed well in the presence of bicarbonate (5 mM), humic acid (10 mg/L), or co-existing cations such as Pb²⁺, Ni²⁺, Cd²⁺, Mn^2+, and Cu²⁺ (200 ug/L) at pH 7.0, and displayed relatively high oxidation resistance and stability ability. This work provides an in-depth understanding of the biogenic CMC-FeS complex for the U(VI) removal and contributes to the development of cost-effective U(VI) remediation technologies.

Methylene blue adsorption on thermo plasma expanded graphite in a multilayer column system

The removal of dyes from wastewater is an important topic in environmental applications. Methylene blue (MB) is one of the most worrisome compounds, as it is widespread and used in many industrial activities. Adsorption represents an effective technique for the removal of this contaminant. Thermo plasma expanded graphite (TPEG) is an industrial material characterized by a fibrous morphology, a very low density and overlapped graphene layers. TPEG has a higher specific surface compared to conventional thermo-expanded graphite and it can establish effective attractive forces with charged pollutants. These properties make TPEG a very promising adsorbent material. In the present work, TPEG was tested in an innovative multilayer column system to treat MB contaminated solutions. Several batch experiments were carried out by varying pH, initial MB concentration and temperature. The optimal adsorption performance was assessed at pH 11, around which the TPEG assumed the maximum negative charge. Based on these results, the adsorption mechanism appeared to be related mainly to electrostatic interactions. At room temperature, the greatest amount of MB adsorbed on TPEG was detected by treating solutions with an initial concentration of 30 mg_MB/L. The temperature increase from 20 to 40 °C caused an enhanced adsorption capacity when concentrations higher than 10 mg_MB/L were treated. The adsorption trends were accurately described by a pseudo-second order kinetic law and the adsorption isotherms at 20 and 40 °C were found to follow both the features of Freundlich and Langmuir models. The adsorption capacity was estimated to reach threshold values around 95 mg_MB/g_TPEG and 265 mg_MB/g_TPEG at 20 and 40°C, respectively. The Gibbs energy change (ΔG°) was calculated to about -7.80 kJ/mol, which proved that the process is spontaneous from a thermodynamic point of view. Finally, it was verified that TPEG can be efficiently reused 5 times after a simple chemical regeneration phase with HCl.

Magnetic biochar prepared by electromagnetic induction pyrolysis of cellulose: Biochar characterization, mechanism of magnetization and adsorption removal of chromium (VI) from aqueous solution

This work introduces a novel methodology for synthesis of magnetic biochar from cellulose using an electromagnetic induction technology. More rough surfaces, sharp corners and edges, and compact regular pore structure with Fe₃O₄ and Fe₂O₃ of magnetic biochar was obtained. Such magnetic biochar possessed higher specific surface area (~236 m²/g) and micropore volume (0.144 m³/g). More hydroxyl groups of magnetic biochars decomposed and reacted with iron ions to form new chemical bonds. The coercivity and remanence of two magnetic biochars were calculated to be 125.76 Oe and 1.26 emu/g, 71.48 Oe and 1.31 emu/g. The total iron leaching rate were 0.94% and 1.28%, indicating magnetic biochar form wet pyrolysis process showed strong magnetization and iron loading stability (98.59%). Alternating electromagnetic field influenced the iron loading capacity and stability by Lorentz force during wet pyrolysis process. Such magnetic biochar can be used for removal of Cr(VI) from wastewater.

Nano zero valent iron encapsulated in graphene oxide for reducing uranium

Nano zero-valent iron (Fe⁰) has been widely used to remove Uranium (U(VI)). In order to enhance the performance of Fe⁰ toward U(VI) removal, the Fe⁰ was assembled into graphene oxide (GO) sheets via 3-aminopropyl triethoxysilane (APTES) as Fe⁰/APTES-GO composites. The Fe⁰/APTES-GO composites were triumphantly prepared, characterized and analyzed by means of Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) together with Energy Dispersive Spectrometer (EDS), X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS). SEM and TEM-EDS results manifested that Fe⁰ particles were encapsulated into rolled-up GO, which greatly improved the stability of Fe⁰. Batch experiment showed that only a small amount of Fe²⁺ was leached in the first two leaching cycles of Fe⁰/APTES-GO composites. The removal capacity of Fe⁰/APTES-GO composites was up to 1357.99 mg/g at pH = 4.1 and T = 50 °C, which was mainly attributed to the reducing activity of Fe⁰ and an abundance of functional groups (i.e., -COOH, C-OH and -OH) on the Fe⁰/APTES-GO composites. The electrostatic potential (ESP) from the calculation also supported that U(VI) tended to be reduced at the back side of the GO-Fe⁰ cluster.

Carbon materials for extraction of uranium from seawater

With the rapid growth of population and industrialization, the energy crisis and environmental pollution as two main difficulties urgently need to be solved nowadays. The development and utilization of nuclear energy is of great significance for solving energy support, national security and environmental protection. As the raw material of nuclear energy, a lot of uranium in seawater provide a guarantee for the sustainable and green development of nuclear power plants. Recently, various new carbon-based materials (e.g., carbon nanofibers, multiwalled carbon nanotube, graphene) have been attracted widely intense interest in extraction of uranium from seawater due to large specific surface area, excellent acid-base resistance, high adsorption performance, environmental friendly and low cost. Thus, the systematic reviews concerning the extraction of uranium from seawater on various carbon-based materials were highly desirable. In this review, the extraction methods of uranium from seawater, including electrochemical, photocatalytic and adsorption methods are briefly introduced. Then the application and mechanism of four generation carbon-based materials on the extraction of uranium from seawater are systematically reviewed in details. Finally, the current challenges and future trends of uranium extraction from seawaters are proposed. This review provides the guideline for designing carbon-based materials with high adsorption capacity and exceptional selectivity for U(VI) extraction from seawater.

Spectroscopic Analyses of Changes in Photocatalytic and Catalytic Activities of Mn- and Ni-Ion Doped and Base-Treated Reduced Graphene Oxide

While reduced graphene oxide (rGO) is used widely as a catalyst, its catalytic activity can be improved significantly by modifying it with a metal. In this study, we compared the photocatalytic and catalytic properties of base-treated rGO particles and transition-metal-ion-doped rGO based on the oxidation reaction of thiophenol and the photocatalytic degradation of 4-chlorophenol. Since the two catalytic activities are related to the changes in the electronic structure of rGO, X-ray photoemission spectroscopy, X-ray absorption spectroscopy, and Raman spectroscopy were performed. When rGO was doped with Mn2+ ions, its catalytic properties improved with respect to both reactions. The changes in the electronic structure of rGO are attributed to the formation of defect structures on the rGO surface via a reaction between the doped Mn2+ ions and oxygen of the rGO surface. Thus, the results show that the doping of rGO with Mn ions in the +2-charge state (stable oxide form: MnO) enhances its catalytic and photocatalytic activities. Hence, this study provides new insights into the use of defect-controlled rGO as a novel catalyst.

A non-polluting method for rapidly purifying uranium-containing wastewater and efficiently recovering uranium through electrochemical mineralization and oxidative roasting

Iron-based materials have been widely used for treating uranium-containing wastewater. However, the iron-uranium solids originating by treating radioactive water through pollutant transfer methods has become a new uncontrolled source of persistent radioactive pollution. The safe disposal of such hazardous waste is not yet well-resolved. The electrochemical mineralization method was developed to rapidly purify uranium-containing wastewater through lattice doping in magnetite and recover uranium without generating any pollutants. An unexpected isolation of U₃O₈ from uranium-doped magnetite was discovered through in-situ XRD with a temperature variation from 300 °C to 700 °C. Through HRTEM and DFT calculation, it was confirmed that the destruction of the inverse spinel crystal structure during the gradual transformation of magnetite into γ-Fe₂O₃ and α-Fe₂O₃ promoted the migration, aggregation, and isolation of uranium atoms. Uniquely generated U₃O₈ and Fe₂O₃ were easily separated and over 80% uranium and 99.5% iron could be recovered. These results demonstrate a new strategy for uranium utilization and the environmentally friendly treatment of uranium-containing wastewater.

Efficient Sequestration of Hexavalent Chromium by Graphene-Based Nanoscale Zero-Valent Iron Composite Coupled with Ultrasonic Pretreatment

Nanoscale zero-valent iron (nZVI) has attracted considerable attention for its potential to sequestrate and immobilize heavy metals such as Cr(VI) from an aqueous solution. However, nZVI can be easily oxidized and agglomerate, which strongly affects the removal efficiency. In this study, graphene-based nZVI (nZVI/rGO) composites coupled with ultrasonic (US) pretreatment were studied to solve the above problems and conduct the experiments of Cr(VI) removal from an aqueous solution. SEM-EDS, BET, XRD, and XPS were performed to analyze the morphology and structures of the composites. The findings showed that the removal efficiency of Cr(VI) in 30 min was increased from 45.84% on nZVI to 78.01% on nZVI/rGO and the removal process performed coupled with ultrasonic pretreatment could greatly shorten the reaction time to 15 min. Influencing factors such as the initial pH, temperature, initial Cr(VI) concentration, and co-existing anions were studied. The results showed that the initial pH was a principal factor. The presence of HPO₄²⁻, NO₃⁻, and Cl⁻ had a strong inhibitory effect on this process, while the presence of SO₄²⁻ promoted the reactivity of nZVI/rGO. Combined with the above results, the process of Cr(VI) removal in US-nZVI/rGO system consisted of two phases: (1) The initial stage is dominated by solution reaction. Cr(VI) was reduced in the solution by Fe²⁺ caused by ultrasonic cavitation. (2) In the following processes, adsorption, reduction, and coprecipitation coexisted. The addition of rGO enhanced electron transportability weakened the influence of passivation layers and improved the dispersion of nZVI particles. Ultrasonic cavitation caused pores and corrosion at the passivation layers and fresh Fe⁰ core was exposed, which improved the reactivity of the composites.

The photocatalytic reduction of U(VI) into U(IV) by ZIF-8/g-C3N4 composites at visible light

The development of new photocatalyst towards the highly efficient photo-reduction of U(VI) was highly desirable. In this study, ZIF-8/g-C₃N₄ photocatalyst was fabricated to photo-reduce U(VI) from aqueous solutions under different water chemistry. It is demonstrated that ZIF-8/g-C₃N₄ exhibited the fast-photocatalytic rate (completely photoreduction within 30 min), high photocatalytic activity (K_d > 10⁵ mL/g) and superior chemical stability (No significant decrease after fifth cycles). The photoreduction rate of U(VI) significantly decreased with increasing pH, H₂O₂ radicals and photo-generated electrons play an important role in U(VI) photoreduction by quenching experiments and ESR analysis. According to XPS and XANES analysis, adsorbed U(VI) was partly photo-reduced into U(IV) by ZIF-8/g-C₃N₄ photocatalyst. The highly efficient removal of U(VI) on ZIF-8/g-C₃N₄ photocatalyst was attributed to the synergistic effect of ZIF-8 and g-C₃N₄ photocatalyst. The present study may provide a new strategy to apply new photocatalyst for in-situ photoreduction of U(VI) in actual environmental remediation.

Effective adsorption of Direct Red 23 by sludge biochar-based adsorbent: adsorption kinetics, thermodynamics and mechanisms study

Using solid adsorbents, such as biochar, has been a potential practice to remove the pollutants from water bodies to render the water safer for potential usage. A potential application of sludge biochar-based adsorbent (SBA), obtained by pyrolysis with hydrothermal treatment, was developed to adsorb Direct Red 23 (DR23) from wastewater. The results showed that for the synthesized SBA (0.5 g/L) in the adsorption of DR23 at low concentration (<20 mg/L), the DR23 was totally removed from the aqueous solution. pH had a limited effect on the adsorption, while an increase in temperature was shown to have a large enhancing effect. The adsorption kinetics were best fitted by the pseudo-second-order kinetic model, while the equilibrium data were best fitted by the Langmuir isotherm. A maximum saturation adsorption capacity of SBA of 111.98 mg/g was achieved. SBA could then be regenerated by pyrolysis, and after three cycles, SBA still retained good adsorption ability for DR23, a removal rate exceeding 97% was achieved. Functional groups, pores, π-π bond, and electrostatic interactions are the key to the adsorption mechanisms. The results proved that SBA would be a promising material in the application of removing dyes in printing and dyeing wastewater.

Potential environmental applications of MXenes: A critical review

Various environmental pollutants (e.g., air, water and solid pollutants) are discharged into environments with the rapid development of industrializations, which is presently at the forefront of global attention. The high efficient removal of these environmental pollutants is of important concern due to their potential threat to human health and eco-diversity. Advanced nanomaterials may play an important role in the elimination of pollutants from environmental media. MXenes as the new intriguing class of graphene-like 2D transition metal carbides and/or carbonitrides have been widely used in energy storage, environmental remediation benefitting from exceptional structural properties such as highly active sites, high chemical stability, hydrophilicity, large interlayer spacing, huge specific surface area, superior sorption-reduction capacity. However, the comprehensive investigation concerning the removal of various environmental pollutants on MXenes is yet not available up to date. In this review, we summarized the synthesis and properties of MXenes to demonstrate the key roles in ameliorating their adsorption performance; then the recent advances and achievements in environmental application of MXenes on the removal of gases, organics, heavy metals and radionuclides were comprehensively reviewed in details; Finally, the formidable challenges and further perspectives regarding utilizing MXene in environmental remediation were proposed. Hopefully, this review can provide the useful information for environmental scientists and material engineers on designing versatile MXenes in actual environmental applications.

Influence of Carbon Nanotube-Pretreatment on the Properties of Polydimethylsiloxane/Carbon Nanotube-Nanocomposites

Incorporating nanofillers into elastomers leads to composites with an enormous potential regarding their properties. Unfortunately, nanofillers tend to form agglomerates inhibiting adequate filler dispersion. Therefore, different carbon nanotube (CNT) pretreatment methods were analyzed in this study to enhance the filler dispersion in polydimethylsiloxane (PDMS)/CNT-composites. By pre-dispersing CNTs in solvents an increase in electrical conductivity could be observed within the sequence of tetrahydrofuran (THF) > acetone > chloroform. Optimization of the pre-dispersion step results in an AC conductivity of 3.2 × 10⁻⁴ S/cm at 1 Hz and 0.5 wt.% of CNTs and the electrical percolation threshold is decreased to 0.1 wt.% of CNTs. Optimum parameters imply the use of an ultrasonic finger for 60 min in THF. However, solvent residues cause a softening effect deteriorating the mechanical performance of these composites. Concerning the pretreatment of CNTs by physical functionalization, the use of surfactants (sodium dodecylbenzenesulfonate (SDBS) and polyoxyethylene lauryl ether (“Brij35”)) leads to no improvement, neither in electrical conductivity nor in mechanical properties. Chemical functionalization enhances the compatibility of PDMS and CNT but damages the carbon nanotubes due to the oxidation process so that the improvement in conductivity and reinforcement is superimposed by the CNT damage even for mild oxidation conditions.

Highly efficient adsorption and immobilization of U(VI) from aqueous solution by alkalized MXene-supported nanoscale zero-valent iron

A novel composite of zero-valent iron nanoparticles supported on alkalized Ti₃C₂T_x nanoflakes (nZVI/Alk-Ti₃C₂T_x) was constructed by an in-situ growth method for simultaneous adsorption and reduction U(VI) from aqueous solution in anoxic conditions. The effect of various factors such as adsorbent dose, pH, ionic strength, contact time, initial U(VI) concentration and environmental media were comprehensively investigated by batch experiments. Benefiting from the good dispersion uniformity of nZVI on MXene substrates, nZVI/Alk-Ti₃C₂T_x exhibited rapid removal kinetics, excellent selectivity, 100% removal efficiency and up to 1315 mg g^-1 uptake capacity for U(VI) capture. In the presence of mimic groundwater, 1.0 mM NaHCO₃ and 10 mg L^-1 humic acid, the removal percentages of U(VI) by the composites could reach 95.1%, 88.9% and 69.5%, respectively. The reaction mechanism between U(VI) and nZVI/Alk-Ti₃C₂T_x has been clarified based on FTIR, XANES, XPS and XRD analysis. Depending on the consumption of reactive nZVI in the composites and the solution pH, the elimination of U(VI) could be realized by different pathways including reductive immobilization in the form of UO₂, inner-sphere surface complexation and hydrolysis precipitation. The present study illustrates that the nZVI/Alk-Ti₃C₂T_x composite may be an efficient scavenger for radioactive wastewater purification in environmental remediation.

NDMA adsorption and degradation by a new-type of Ag-MONT material carrying nanoscale zero-valent iron

Nitrosamines, which are emerging nitrogenous disinfection by-products, have raised great concern owing to their carcinogenicity and genotoxicity. Thus, exploring efficient materials to remove nitrosamines from the environment is of vital importance. In this work, NaBH₄ was taken as a reducing agent and Ag-based metal organic nanotubes (Ag-MONTs) were impregnated in FeSO₄·7H₂O to prepare nanoscale zero-valent iron (nZVI) supported on the nanotubes (nZVI@Ag-MONTs). The new material was then characterized and applied to N-dimethylnitrosamine (NDMA) adsorption and degradation in water. The material had excellent ability to adsorb and degrade NDMA, and the total concentrations of iron and silver remaining in water did not exceed standard limits after 120 min of adsorption. Coexisting substances, such as NO₃^-, Cl^-, CO₃^2-, humic acid, trichloromethane, and trichloronitromethane, did not affect the NDMA removal efficiency of the adsorbent. The NDMA removal efficiency of the new material exceeded 88% even in the presence of SO₄^2- and PO₄^3-. The NDMA degradation mechanism of nZVI@Ag-MONTs included a catalytic hydrogenation reaction and resulted in dimethylamine as the final degradation product. The nZVI@Ag-MONTs showed favorable stability and reusability. Taking the results together, the nZVI@Ag-MONTs proposed in this work are applicable to NDMA adsorption and degradation in water.

Efficient and selective removal of SeVI and AsV mixed contaminants from aqueous media by montmorillonite-nanoscale zero valent iron nanocomposite

Nanoscale zero-valent iron (NZVI) and NZVI supported onto montmorillonite (NZVI-Mt) were synthetized and used in this study to remove Se^VI and As^V from water in mono- and binary-adsorbate systems. The adsorption kinetics and isotherm data for Se^VI and As^V were adequately described by the pseudo-second-order (PSO) (r²>0.94) and Freundlich (r²>0.93) equations. Results from scanning electron microscopy showed that the dimension of the NZVI immobilized on the Mt was smaller than pure NZVI. Using 0.05 g of adsorbent and an initial 200 mg L^-1 As^V and Se^VI concentration, the maximum adsorption capacity (q_max) and partition coefficient (PC) for As^V on NZVI-Mt in monocomponent system were 54.75 mg g^-1 and 0.065 mg g^-1·μM^-1, which dropped respectively to 49.91 mg g^-1 and 0.055 mg g^-1·μM^-1 under competitive system. For Se^VI adsorption on NZVI-Mt in monocomponent system, q_max and PC were 28.63 mg g^-1 and 0.024 mg g^-1·μM^-1, respectively. Values of q_max and PC were higher for NZVI-Mt than NZVI and montmorillonite, indicating that the nanocomposite contained greater adsorption sites for removing both oxyanions, but with a marked preference for As^V. Future research should evaluate the effect of different operational variables on the removal efficiency of both oxyanions by NZVI-Mt.