Oxidation of Rhodamine B by persulfate activated with porous carbon aerogel through a non-radical mechanism

Enhanced adsorption of tylosin by ordered multistage porous carbon and efficient in-situ regeneration of saturated adsorbents by activated persulfate oxidation: Performance, mechanism and multiple cycles

In this study, a novel ordered multistage porous carbon (OMPC) with a micro-mesoporous structure was prepared and used for the removal of tylosin (TYL). The porous material, carbonized at 900 °C (OMPC-900), exhibited micro-mesoporous structures with pore sizes of 0.71 nm and 3.63 nm, while had a specific surface area of 1300.02 m2∙g-1. OMPC-900 demonstrated a maximum adsorption capacity of 341.28 mg∙g-1 for TYL in water by electrostatic attraction, hydrogen bonding, π-π interactions, and pore-filling mechanisms, which is 6.41 times higher than that of activated carbon. The TYL-saturated adsorbents could be efficiently regenerated by in-situ oxidation through the activation of persulfate (PDS), achieving a regeneration rate of 94.17%, significantly higher than that of activated carbon (55.22%). The excellent regeneration performance may be attributed to the presence of -C=O and graphitic carbon in the adsorbent, which promotes the production of free radicals (•OH, SO4•- and •O2-) and non-free radicals. Among these, the non-radical pathways (1O2 and electron transfer) played a key role in the degradation of TYL loaded on the adsorbent. OMPC-900 maintained stable regenerative adsorption performance of 80.85% after five in-situ regeneration, and the normalized adsorption capacity per unit surface area increased from 0.21 to 0.39 mg∙m-2, which may be due to that the increase in oxygen-carbon ratio and surface defects improved the adsorption sites activity of the regenerated adsorbent. In comparison to conventional pyrolysis and organic solvent elution, oxidative regeneration through the activation of PDS is a more efficient and sustainable method.

Activated persulfate for efficient bisphenol A degradation via nitrogen-doped Fe/Mn bimetallic biochar

To achieve the purpose of treating waste by waste, in this study, a nitrogen-doped Fe/Mn bimetallic biochar material (FeMn@N-BC) was prepared from chicken manure for persulfate activation to degrade Bisphenol A (BPA). The FeMn@N-BC was characterized by scanning electron microscopy (SEM), X-ray diffract meter (XRD), fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectrometer (XPS) and found that N doping can form larger specific surface area. Catalytic degradation experiments showed that Fe/Mn bimetal doping not only accelerated the electron cycling rate on the catalyst surface, but also makes the biochar magnetic and easy to separate, thus reducing environmental pollution. Comparative experiments was concluded that the highest degradation efficiency of BPA was achieved when the mass ratios of urea and chicken manure, Fe/Mn were 3:1 and 2:1, respectively, and the pyrolysis temperature was 800 °C, which can almost degrade all the BPA in 60 min. FeMn@N-BC/PS system with high catalytic efficiency and low consumables is promising for reuse of waste resources and the remediation of wastewater.

Refractory degradable dissolved organic matter (R-DOM) driving nitrogen removal by the electric field coupled iron‑carbon biofilter (E-ICBF): Performance and microbial mechanisms

Researches on the advanced nitrogen (N) removal of municipal tailwater always overlooked the value of refractory degradable dissolved organic matter (R-DOM). In this study, a novel electric field coupled iron‑carbon biofilter (E-ICBF) was utilized to explore the performance and microbial changes with polyethylene glycol (PEG) as the representative R-DOM. Results demonstrated that the removal efficiencies of E-ICBF for nitrate nitrogen (NO3--N), ammonia nitrogen (NH4+-N), and total nitrogen (TN) improved by 28.76 %, 12.96 %, and 28.45 %, compared to quartz sand biofilter (SBF). Moreover, removal efficiencies of NO3--N and TN in E-ICBF with R-DOM went up by 12.11 % and 14.02 % compared to methanol. Additionally, both PEG and the electric field reduced the microbial richness and diversity. However, PEG promoted the increase of denitrifying bacteria abundance including unclassified_f_Comamonadaceae, Thauera, and unclassified_f_Gallionellaceae. The electric field improved the abundances of genes related to N removal (hao, nasC, nasA, nifH, nifD, nifK) and PEG further enhanced the effect. The abundances of key enzymes [EC:1.7.5.1], [EC:1.7.2.1], [EC:1.7.2.4], and [EC:1.7.2.5] decreased due to the addition of PEG and the electric field mitigated the negative influence. Additionally, the electric field changed relationships between microorganisms and pollutant removal, and improved interspecific relationships between denitrifying bacterial genera and other genera in E-ICBF.

Removal of tetracycline in the water by a kind of S/N co-doped tea residue biochar

Tetracycline (TC) is widely present in the environment, and adsorption technology is a potential remediation method. S/N co-doped tea residue biochar (SNBC) was successfully prepared by hydrothermal carbonization method using tea residue as raw material. S was doped by Na2S2O3·5H2O, and N was doped by N in tea residue. The adsorption efficiency of SNBC could reach 94.16% when the concentration of TC was 100 mg L-1. The adsorption effect of SNBC on TC was 9.38 times more than that of unmodified biochar. Tea biochar had good adsorption effect at pH 4-9. The maximum adsorption capacity of 271 mg g-1 was calculated by the Langmuir isotherm model. The adsorption mechanism involved many mechanisms such as pore filling, π-π interaction and hydrogen bonding. The adsorbent prepared in this study could be used as an effective adsorbent in the treatment of TC wastewater.

From rust to robust disinfectants: How do iron oxides and inorganic oxidants synergize with UVA light towards bacterial inactivation?

Pathogens in drinking water remain a challenge for human health, photo-Fenton process is a promising technique for pathogen inactivation, herein, two common iron oxides, hematite and magnetite mediate persulfate (peroxymonosulfate-PMS - and peroxydisulfate-PDS) involved photo-Fenton-like processes were constructed for E. coli inactivation, and the inactivation performance was investigated and compared with the photo-Fenton process under a low intensity UVA irradiation. Results indicated that with a low dose of iron oxides (1 mg/L) and inorganic peroxides (10 mg/L), PMS-involved photo-Fenton-like process is the best substitute for the photo-Fenton one over pH range of 5-8. In addition, humic acid (HA, one of the important components of natural organic matter) incorporated iron oxide-mediated photo-Fenton-like processes for bacteria inactivation was also studied, and facilitating effect was found in UVA/hematite/PMS and UVA/magnetite/PDS systems. Reactive oxygen species (ROS) exploration experiments revealed that ·OH was the predominant radical in H2O2- and PDS-containing systems, whereas 1O2 was one of the principal reactive species in the PMS systems. In addition to the semiconductor photocatalysis of iron oxides and UVA-activated oxidants, iron-complexes (iron-oxidant complexes and iron-bacteria complexes) mediated ligand-to-metal charge transfer (LMCT) processes also made contribution to bacterial inactivation. Overall, this study demonstrates that it is feasible to replace H2O2 with PMS in a photo-Fenton-like process for water disinfection using a low dose of reagents, mediated by cheap catalysts, such as hematite and magnetite, it is also hoped to provide some insights to practical water treatment.

Theory-guided unraveling of the mechanism underlying Cu1.0/Mn1.0-ZnO with dual reaction centers for enhanced peroxymonosulfate activation

Developing efficient catalytic systems for water contamination removal is a topic of great interest. However, the use of heterogeneous catalysts faces challenges due to insufficient active sites and electron cycling. In this study, results from first-principles calculations demonstrate that dual reaction centers (DRCs) are produced around the Cu and Mn sites in Cu1.0/Mn1.0-ZnO due to the electronegativity difference. Experimental results reveal the material with DRCs greatly enhances electron transfer efficiency and significantly impacts the oxidation and reduction of peroxymonosulfate (PMS). In addition, the self-consistent potential correction (SCPC) method was introduced to correct the energy and charge of charged periodic systems simulating a catalytic process, resulting in more precise catalytic results. Specifically, the material exhibits a preference for adsorbing negatively charged PMS anions at electron-deficient Mn sites, facilitating PMS oxidation for the generation of 1O2, and PMS reduction around the electron-rich Cu for the formation of •OH and SO4•-. The major reactive oxygen species is 1O2, showcasing effective performance in various degradation systems. Overall, our work provides novel insights into the persulfate-based heterogeneous catalytic oxidation process, paving the way for the development of high-performance catalytic systems for water purification.

Singlet oxygen dominance for phenolic degradation mediated by mixed-valence FeOx nanospheres

In this investigation, we successfully synthesized magnetic FeOx nanosphere catalysts with mixed-valence and high operational stability through the pyrolysis of a hybrid material containing polyferrocenlyphosphazene with coordinating heteroatoms (N, P, O). We evaluated the degradation performance of these catalysts using the peroxymonosulfate (PMS) activation process against four different phenolic compounds, namely phenol, 4-nitrophenol, 2,4-dinitrophenol, and 2,4,5-trinitrophenol. Our results demonstrate the significant role of FeOx in the degradation process. The presence of mixed iron species, such as ferric iron, zero-valent iron, and iron oxides, activated PMS to generate radicals. Additionally, the heteroatoms facilitated the anchoring and dispersion of FeOx nanospheres while also breaking the inertness of the carbon structure. Notably, the FeOx-800 catalyst exhibited a maximum degradation activity of 98% for phenol, surpassing its counterparts. Electron paramagnetic resonance and free radical scavenging experiments confirmed that singlet oxygen (1O2) is the principal reactive oxygen species (ROS) that leads to the oxidative breakdown of phenolic compounds. This study introduces new concepts for designing Fenton-like catalysts incorporating heteroatoms into the carbon matrix. Due to their low cost and non-toxicity, these catalysts have recently received a great deal of attention for peroxymonosulfate (PMS) activation and environmental remediation.

Polydopamine-modified MOF-5-derived carbon as persulfate activator for aniline aerofloat degradation

Residual flotation chemicals in beneficiation wastewater seriously threaten local ecosystems, such as groundwater or soil, and must be treated effectively. Currently, the degradation of organic pollutants using nitrided MOFs-derived carbon to activate persulfate (PDS) has attracted considerable attention. Hence, we developed a new synthetic strategy to load dopamine hydrochloride (PDA) onto MOF-5-derived porous carbon (PC) to form NPC, and the degradation of a typical flotation Aniline aerofloat (AAF) at high salinity by a low dose of the NPC/PDS system was investigated. Several characterization analyses such as TEM, XRD, Raman, FT-IR and XPS demonstrated that the nitrogen-rich indolequinone unit in PDA provided nitrogen to PC during the pyrolysis process. This enabled the core-shell structure of NPC and the synergy among the multiple components to induce the AAF degradation by PDS over a wide pH scale in a short period of time. It was deduced that the degradation of AAF by the NPC-8/PDS system was a non-radical pathway dominated by 1O2, which relied mainly on the conversion of superoxide radicals (O2•-) and surface-bound radicals. Among them, the pyridine N in the sp2 hybrid carbon was considered as a possible active site. This non-radical pathway was resistant to pH changes and background substances in the water, and well overcame the inhibition of the reaction by natural organic substances and inorganic anions in natural water. In this study, A novel approach to the synthesis of homogeneous MOFs nuclear-derived porous carbon was proposed and the application of MOFs-derived porous carbon for AAF remediation of mineral processing wastewater was broadened.

Applications of Carbon-Based Materials in Activated Peroxymonosulfate for the Degradation of Organic Pollutants: A Review

In recent years, water pollution has posed a serious threat to aquatic organisms and humans. Advanced oxidation processes (AOPs) based on activated peroxymonosulfate (PMS) show high oxidation, good selectivity, wide pH range and no secondary pollution in the removal of organic pollutants in water. Carbon-based materials are emerging green catalysts that can effectively activate persulfates to generate radical and non-radical active species to degrade organic pollutants. Compared with transition metal catalysts, carbon-based materials are widely used in SR-AOPs because of their low cost, non-toxicity, acid and alkali resistance, large specific surface area, and scalable surface charge, which can be used for selective control of specific water pollutants. This paper mainly presents several carbon-based materials used to activate PMS, including raw carbon materials and modified carbon materials (heteroatom-doped and metal-doped), analyzes and summarizes the mechanism of activating PMS by carbon-based catalysts, and discusses the influencing factors (temperature, pH, PMS concentration, catalyst concentration, inorganic anions, inorganic cations and dissolved oxygen) in the activation process. Finally, the future challenges and prospects of carbon-based materials in water pollution control are also presented.

Degradation of p-Nitrophenol by activated persulfate with carbon-based materials

The removal of p-nitrophenol (PNP) from wastewater was evaluated by the activated persulfate process using different materials - carbon xerogels (XG), carbon nanotubes (CNT), and activated carbon (AC) -, and also using such materials doped with nitrogen (XGM, CNTM and ACM). These carbon materials were impregnated with 2 wt.% of iron and tested in the oxidative process to assess the influence of their textural and surface chemical properties. The carbon-based materials' properties influence the efficiencies of the adsorption and oxidative processes; in adsorption, the materials with higher specific surface areas (S_BET), i.e. AC (824 m²/g) and Fe/AC (807 m²/g), have shown to be the most promising (having achieved a PNP removal of about 20%); on the other hand, in the activated persulfate process the carbon or iron-containing carbon materials with the highest mesoporous areas (S_meso) were the preferential ones - XG and Fe/XG, respectively - reaching removals of 47.3% and 75.7% for PNP and 44.9 and 63.3% for TOC, respectively. Moreover, the presence of nitrogen groups on the samples' surface benefits both processes, being found that PNP degradation and mineralization increase with the nitrogen content. The stability of the best materials (XGM and Fe/XGM) was evaluated during four cycles, being noticed that while XGM lost catalytic activity, the Fe/XGM sample remained stable without leaching of iron. The quantification of intermediate compounds formed during persulfate oxidation was performed, and only oxalic acid was detected, in addition to PNP, being that their contribution to the TOC measured was higher than 99%. Experiments carried out in the presence of radical scavengers proved that only the sulfate radical is present under the acidic conditions used. Complete PNP oxidation and TOC removal of ∼96% were reached for the activated persulfate process, proving to be more attractive than the Fenton one.

Nitrogen doped bimetallic sludge biochar composite for synergistic persulfate activation: Reactivity, stability and mechanisms

As a recycling use of waste activated sludge (WAS), we used high-temperature pyrolysis of WAS to support bimetallic Fe-Mn with nitrogen (N) co-doping (FeMn@N-S), a customized composite catalyst that activates peroxysulphate (PS) for the breakdown of tetracycline (TC). First, the performance of TC degradation was evaluated and optimized under different N doping, pH, catalyst dosages, PS dosages, and contaminant concentrations. Activating PS with FeMn@N-S caused the degradation of 91% of the TC in 120 min. Next, characterization of FeMn@N-S by XRD, XPS and FT-IR analysis highlights N doping is beneficial to take shape more active sites and reduces the loss of Fe and Mn during the degradation reaction. As expected, the presence of Fe-Mn bimetallic on the catalyst surface increases the rate of electron transfer, promoting the redox cycle of the catalyst. Other functional groups on the catalyst surface, such as oxygen-containing groups, accelerated the electron transfer during PS activation. Free radical quenching and ESR analysis suggest that the main contributor to TC degradation is surface-bound SO₄^•-, along with the presence of single linear oxygen (¹O₂) oxidation pathway. Finally, the FeMn@N-S composite catalyst exhibits excellent pH suitability and reusability, indicating a solid practicality of this catalyst in PS-based removal of antibiotics from wastewater.

One-step preparation of a novel graphitic biochar/Cu0/Fe3O4 composite using CO2-ambiance pyrolysis to activate peroxydisulfate for dye degradation

Herein, a one-step co-pyrolysis protocol was adopted for the first time to prepare a novel pyrogenic carbon-Cu⁰/Fe₃O₄ heteroatoms (FCBC) in CO₂ ambiance to discern the roles of each component in PDS activation. During co-pyrolysis, CO₂ catalyzed formation of reducing gases by biomass which facilitated reductive transformation of Fe³⁺ and Cu²⁺ to Cu⁰ and Fe₃O₄, respectively. According to the analysis, the resulting metal (oxide) catalyzed graphitization of biocharand decomposition of volatile substances resulting in an unprecedented surface area (1240 m^2/g). The resulting FCBC showed greater structural defects and less electrical impedance. Batch experiments indicated that Rhodamine B (RhB) degradation by FCBC (100%) was superior to Fe₃O₄ (50%) and Cu⁰/Fe₃O₄ (76.4%) in persulfate (PDS) system, which maintained reasonable efficiency (75.6%-63.6%) within three cycles. The reactive oxygen species (ROS) associated with RhB degradation was identified by an electron paramagnetic resonance and confirmed by scavenging experiments. RhB degradation invoked both (sulfate and dominantly hydroxyl) radical and non-radical (singlet oxygen, ¹O₂) pathways. Regarding FCBC, Cu⁰ can continuously react with Fe³⁺ in Fe₃O₄ to generate larger quantities of Fe²⁺, and both Cu⁰ and Fe²⁺ activated PDS to yield sulfate radicals which was quickly converted to hydroxyl radical. Besides, Cu⁰/Cu²⁺ could complex with PDS to form a metastable complex, which particularly contributed to ¹O₂ generation. These cascade reactions by FCBC were reinforced by carbonyl group of biochar and favorable electron transfer ability. This work highlighted a new approach to prepare a magnetic and environment-benign heterogonous catalyst to remove organic pollutants in water.

Enhanced catalytic activity and stability of composite of cellulose film and nano zero-valent iron on Juncus effusus for activating peroxydisulfate to degrade Rhodamine B dye

In this study, a novel peroxydisulfate (PDS) activator (CF-nZVI-JE) was prepared via in-situ loading nano zero-valent iron (nZVI) on Juncus effusus (JE) followed with wrapping a layer of cellulose film (CF). The CF-nZVI-JE had the same 3D structure as the JE, being easy to separate from aqueous solution. The loaded nZVI existed single nanoparticles with a size of 60-100 nm except chain-type agglomeration of nanoparticles due to the stabilization of JE fibers. The activation performance of the CF-nZVI-JE for PDS was evaluated with Rhodamine B (Rh B) as a representative pollutant. Under the optimal activating conditions, the degradation rate of Rh B reached 99% within 30 min in the CF-nZVI-JE/PDS system. After five cycles, the degradation rate of Rh B was still over 85%, suggesting that the CF-nZVI-JE had good reusability. More interestingly, SO₄^·- and ·OH radicals were simultaneously detected in the CF-nZVI-JE/PDS system, but only SO₄^·- existed in the JE-ZVI/PDS system, suggesting the different activation mechanism. Meanwhile, the introduction of CF not only facilitated to the mineralization of Rh B but also significantly reduced the release amount of iron ions. Hence, the CF-nZVI-JE can be employed as a promising PDS activator for the treatment of organic wastewater.

The adsorption affinity of N-doped biochar plays a crucial role in peroxydisulfate activation and bisphenol A oxidative degradation

Metal-free biochar to activate persulfate and degrade organic contaminants has attracted great attention in advanced oxidation processes, while the role of biochar adsorption in the activation and oxidative decomposition process still needed to be further clarified. In this study, nitrogen-doped porous biochar derived from a waste litchi branch was prepared as a peroxydisulfate (PDS) activator for bisphenol A (BPA) degradation, in which the regulation behavior of biochar adsorption was evaluated on the basis of phase distribution and PDS activation mechanism. N-doped biochar obtained at 800 °C with urea and sodium bicarbonate added presented a high specific surface area (821 m2/g), abundant nanopores, and a graphitic structure, and showed the best adsorption capacity and catalytic activity toward BPA. At a dosage of 0.15 g/L NBC-800, 95% BPA can be completely degraded within 60 min with an apparent rate constant (kobs) of 0.0483 min-1. The identified active sites and reactive oxygen species as well as electrochemical tests suggested that both free radicals O2•- and •OH and nonradical pathways including 1O2 originated from C = O and surface electron-transfer mechanisms were involved in BPA decomposition. The experiments and activation mechanisms all confirmed that BPA adsorption on the NBC-800 surface was an extremely crucial step for BPA oxidative degradation.

Fast peroxydisulfate oxidation of the antibiotic norfloxacin catalyzed by cyanobacterial biochar

Peroxydisulfate (PDS) is a common oxidant for organic contaminant remediation. PDS is typically activated by metal catalysts to generate reactive radicals. Unfortunately, as radicals are non-selective and metal catalysts may cause secondary contamination, alternative selective non-radical pathways and non-metal catalysts need attention. Here we investigated PDS oxidation of commonly detected antibiotic Norfloxacin (NOR) using cyanobacterial nitrogen rich biochars (CBs) as catalysts. NOR was fully degraded by CB pyrolysed at 950 °C (CB950) within 120 min. CB950 caused threefold faster degradation than low pyrolysis temperature (PT) CBs and achieved a maximum surface area normalized rate constant of 4.38 × 10^-2 min^-1 m^-2 L compared to widely used metal catalysts. CB950 maintained full reactivity after four repeated uses. High defluorination (82%) and mineralization (>82%) were observed for CB950/PDS. CBs were active over a broad pH range (3-10), but with twice as high rates under alkaline compared with neutral conditions. NOR is degraded by organic, ^•OH and SO₄^•- radicals in low PT CBs/PDS systems, where the presence of Mn^II promotes radical generation. Electron transfer reactions with radicals supplemented dominate high PT CBs/PDS systems. This study demonstrates high PT biochars from algal bloom biomass may find use as catalysts for organic contaminant oxidation.

pH-dependent generation of radical and nonradical species for sulfamethoxazole degradation in different carbon/persulfate systems

The impacts of pH on purification efficiency can be phenomenal in advanced oxidation processes (AOPs), because solution pH affects persulfate (PS) activation processes. However, consensus has not been reached on the regimes of pH-regulated oxidation in persulfate-based AOPs (PS-AOPs). Particularly, the impacts of pH on carbon-catalyzed generation of radical and nonradical species remain unclear. In this work, we evaluated three typical carbonaceous materials including pyrolytic carbon (PC), activated carbon (AC), and carbon nanotube (CNT) to activate PS for sulfamethoxazole (SMX) degradation within a pH range from 4 to 9. The experiment revealed pH-dependent SMX removal in PC/PS, AC/PS, and CNT/PS, and the kinetics followed an order of pH 4 > pH 7 > pH 9. Solution pH simultaneously affected SMX adsorption and degradation, but the latter was more profound. Chemical quenching experiment, electrochemical measurement, kinetics calculation, and ATR-FTIR tests collectively revealed that high pH was not favorable for both radical and nonradical oxidation. In the PC/PS system, increased pH decreased the amount of phenolic -OH on PC surface, thereby restraining the generation of SO₄^•- and ^•OH due to the lack of electron donors. For AC/PS system, elevated pH hindered the interactions between AC and PS, thus suppressing the formation of surface-bound radicals. CNT/PS initiated an electron-transfer pathway, and increased pH reduced the oxidation potential of surface CNT-PS* complex, which was not favorable for nonradical oxidation of adsorbed pollutants. Therefore, outcomes of this work will advance the current knowledge on the intrinsic impacts of pH in PS-AOPs catalyzed by carbonaceous materials for wastewater purification.

Reduced Graphene Oxide Triggers Peracetic Acid Activation for Robust Removal of Micropollutants: The Role of Electron Transfer

Peracetic acid (PAA) serves as a potent and low-toxic oxidant for contaminant removal. Radical-mediated catalytic PAA oxidation processes are typically non-selective, rendering weakened oxidation efficacy under complex water matrices. Herein, we explored the usage of reduced graphene oxide (rGO) for PAA activation via a non-radical pathway. Outperforming the most catalytic PAA oxidation systems, the rGO-PAA system exhibits near-complete removal of typical micropollutants (MPs) within a short time (<2 min). Non-radical direct electron transfer (DET) from MPs to PAA plays a decisive role in the MP degradation, where accelerated DET is achieved by a higher potential of the rGO-PAA reactive surface complexes. Benefitting from DET, the rGO-PAA system shows robust removal of multiple MPs under complex water matrices and with low toxicity. Notably, in the DET regime, the electrostatic attraction of rGO to both PAA and target MP is a critical prerequisite for achieving efficient oxidation, depending on the conditions of solution pH and MP pK_a. A heatmap model building on such an electrostatic interaction is further established as guidance for regulating the performance of the DET-mediated PAA oxidation systems. Overall, our work unveils the imperative role of DET for rGO-activated PAA oxidation, expanding the knowledge of PAA-based water treatment strategies.

Rapid degradation of p-arsanilic acid and simultaneous removal of the released arsenic species by Co-Fe@C activated peroxydisulfate process

In this study, a bimetallic composite catalyst (Co-Fe@C) was fabricated with calcination at high temperature (800 °C) by using Co-MIL-101 (Fe) as the precursor. The characterization results showed that the resulted Co-Fe@C composite mainly consisted of carbon, FeCo alloys, Fe₃O₄, Co₃O₄ and FeO, and owned evident magnetism. In addition, the Co-Fe@C was employed to activate the peroxydisulfate (PDS) to degrade a representative organic pollutant (p-arsanilic acid, p-ASA) and the main factors were optimized, which involved 0.2 g L^-1 of catalyst dosage, 1.0 g L^-1 of PDS dosage and 5.0 of initial pH. Under the optimal condition, Co-Fe@C/PDS system could completely degrade p-ASA (20 mg L^-1) in 5 min. In the Co-Fe@C/PDS system, SO₄^-·, Fe(IV) and ·OH were the main species during p-ASA degradation. Under the attack of these species, p-ASA was first decomposed into phenols and then transformed into the organics acids and finally mineralized into CO₂ and H₂O through a series of reactions like hydroxylation, dearsenification, deamination and benzene ring opening. Importantly, most of the released inorganic arsenic species (93.40%) could be efficiently adsorbed by the catalyst.

Polydopamine-Modified Cellulose Nanofibril Composite Aerogel: An Effective Dye Adsorbent

In this study, a new cellulose nanofibril (CNF) composite aerogel was fabricated using a green and facile mussel-inspired coating strategy. First, the CNF hydrogel was crosslinked by calcium ion followed by immersion in dopamine solution. Second, the surface of CNF was modified using polydopamine (PDA) to obtain PDA@CNF (PCNF) composite aerogel. The PCNF composite aerogels had large surface areas (368.15 m²/g) and low bulk density (27.2 mg/cm³). The composite aerogel exhibited improved mechanical properties, which were almost three times compared with those of CNF aerogel. Moreover, PCNF composite aerogel had good resilience under a wet state. The PDA functional layer remarkably enhanced the adsorption capacities of the composite aerogel for methylene blue (MB). The maximum adsorption of MB was 208 mg/g at an initial dye concentration of 50 mg/L. The adsorption isotherm and kinetic behaviors of the composite aerogel were consistent with Langmuir and pseudo-second-order models. In addition, the PCNF composite aerogels had a high adsorption capacity over a wide pH range. The reuse experiment showed that the removal efficiency of the composite aerogel remained higher than 85% after five cycles. Therefore, PCNF composite aerogels may have potential application in wastewater treatment due to its environmental sustainability and low energy consumption.

Removal of chlortetracycline from water using spent tea leaves-based biochar as adsorption-enhanced persulfate activator

Antibiotic compounds have caused serious environmental concerns. In this study, we developed an effective technology for treatment of chlortetracycline (CTC), a widely used antibiotic compound. A natural heteroatom-doped spent tea leaves-based biochar (STLB) with excellent adsorption and catalytic property was prepared by simple thermal treatment. An adsorption-promoted persulfate-based advanced oxidation process (PS-AOP) using STLB was studied for CTC removal. The results showed that the as-prepared STLB presented favorable adsorption affinity towards CTC with the maximum adsorption capacity of 627 mg g^-1. Meanwhile, CTC enriched on the surface of STLB was good for in-situ decomposition of CTC and nearly 97.4 % of CTC was removed within 30 min of pre-adsorption and 60 min of subsequent degradation. The STLB had excellent recyclability and wide pH tolerance range of 3.0-9.0 in combined pre-adsorption and PS-AOP. Reactive oxygen species analysis confirmed that CTC degradation was mainly due to non-radical (singlet oxygen, ¹O₂) and radicals (SO₄^- and OH). This study suggests that STLB is a promising adsorption-enhanced PS activator for the treatment of refractory wastewater and also provides a strategy of waste control by spent tea leaves.

One-step pyrolysis for preparation of sulfur-doped biochar loaded with iron nanoparticles as an effective peroxymonosulfate activator for RhB degradation

In this study, sulfur-doped biochar loaded with iron nanoparticles (Fe/S-BC) was easily prepared by a one-pot pyrolysis method using anhydrous FeCl3, Na2S2O3·5H2O, and cherry stone powder as raw materials and...

Strong Pyro-Electro-Chemical Coupling of Elbaite/H2O2 System for Pyrocatalysis Dye Wastewater

Elbaite is a natural silicate mineral with a spontaneous electric field. In the current study, it was selected as a pyroelectric catalyst to promote hydrogen peroxide (H2O2) for dye decomposition due to its pyro-electro-chemical coupling. The behaviors and efficiency of the elbaite/H2O2 system in rhodamine B (RhB) degradation were systematically investigated. The results indicate that the optimal effective degradability of RhB reaches 100.0% at 4.0 g/L elbaite, 7.0 mL/L H2O2, and pH = 2.0 in the elbaite/H2O2 system. The elbaite/H2O2 system exhibits high recyclability and stability after recycling three times, reaching 94.5% of the degradation rate. The mechanisms of RhB degradation clarified that the hydroxyl radical (·OH) is the main active specie involved in catalytic degradation in the elbaite/H2O2 system. Moreover, not only does elbaite act as a pyroelectric catalyst to activate H2O2 in order to generate the primary ·OH for subsequent advanced oxidation reactions, but it also has the role of a dye sorbent. The elbaite/H2O2 system shows excellent application potential for the degradation of RhB.

Fe@C activated peroxymonosulfate system for effectively degrading emerging contaminants: Analysis of the formation and activation mechanism of Fe coordinately unsaturated metal sites

Carbon-encapsulated Fe nanocomposites (Fe@C), obtained by pyrolysis of metal-organic frameworks (MOFs), can activate peroxymonosulfate (PMS) to remove emerging contaminants (ECs). Unfortunately, the current MOFs-derived catalysts always inevitably produce more iron-oxide compounds that unfavorable for PMS activation. In this work, according to the thermogravimetric curve of Fe(II)-MOF-74, to discuss the role of pyrolysis temperature on the structural characteristics of Fe@C. The results demonstrated that Fe@C-4 could obtain abundant coordinately unsaturated metal sites and exhibited the best activation performance. Radical-quenching experiments and EPR measurements confirm that the generated sulfate radical (SO₄^-˙) and singlet oxygen (¹O₂) only degraded approximately 35% of TBBPA. Meanwhile, negatively charged complex intermediates formed by the weak interaction between Fe@C-4 and PMS was proposed as the dominant reactive species, and approximately 65% of TBBPA was degraded. This work optimizes the synthesis strategy and mechanism of Fe@C and provides a methodological reference for the design of Fe-based catalysts.

Multipath elimination of bisphenol A over bifunctional polymeric carbon nitride/biochar hybrids in the presence of persulfate and visible light

Polymeric carbon nitride (PCN) has become a star material either in photocatalysis or in persulfate (PS) activation. In this work, we synthesized bifunctional biochar (BC)-doped PCN through a facile one-pot thermal treatment process. The PCN/BC hybrid (CNBC) with an optimized proportion could not only activate PS directly, but also possessed improved optical properties. Amorphous BC domains generated from the carbonization of external corncob provided attachments for the in-situ growth of PCN and upgraded its catalytic ability including electron transport property, visible light (VIS) utilization, and oxidation power. Mechanism studies demonstrated that in the CNBC/PS system without VIS, a nonradical electron transfer route was responsible for the degradation of bisphenol A (BPA), while in the CNBC/PS/VIS system, radical/nonradical mixing mechanisms including mediated electron transfer, radical oxidation, and hole oxidation were unveiled. Degradation pathways of BPA were deduced including direct oxidation at the aromatic ring, β-scission of isopropyl, and ring cleavage. Most of the intermediates were less toxic than BPA as assessed by the ECOSAR software. The CNBC/PS/VIS system showed satisfactory resistance to environmental interferences except for HCO₃^-. This work provides a simple but effective strategy for the synthesis of PCN-based bifunctional catalysts and deepens mechanistic insights into hybrid advanced oxidation technologies.

A comparative study of peroxydisulfate and peroxymonosulfate activation by a transition metal-H2O2 system

In this study, the impacts of common activation methods, namely heating, the addition of zero-valent metals (Cu, Fe, Al, Co, and Ni) and the addition of H₂O₂, on peroxydisulfate (PS) and peroxymonsulfate (PMS) activation were investigated. Rhodamine B (Rhb, 50 mg/L) was chosen as the substrate to be tested. Results showed that the efficiency of PMS was higher than that of PS under the same heat activation conditions. Cu, Fe, and Ni activated PS, while Co exhibited detrimental effects; Among them, Cu was the best. Co was the best activator among the investigated metals for PMS. Additionally, the use of H₂O₂ achieved a higher removal of Rhb in the PS/Cu system but inhibited the PMS/Co system. Three common anions (SO₄^2-, Cl^-, NO₃^-) that exist in the Yellow River were investigated. Cl^- was found to accelerate Rhb degradation, while SO₄^2- and NO₃^- slowed Rhb degradation. Toxicity experiment results showed that the addition of H₂O₂ promoted the transformation of Cu (0) to Cu²⁺ and Co (0) to Co²⁺, which was dangerous for seed germination. Graphical abstract.

Degradation Efficiency and Kinetics Analysis of an Advanced Oxidation Process Utilizing Ozone, Hydrogen Peroxide and Persulfate to Degrade the Dye Rhodamine B

In this study, the effectiveness of a rhodamine B (RhB) dye degradation process at a concentration of 20 mg/L in different advanced oxidation processes—H2O2/UV, O3/UV and PDS/UV—has been studied. The use of UV in a photo-assisted ozonation process (O3/UV) proved to be the most effective method of RhB decolorization (90% after 30 min at dye concentration of 100 mg/L). The addition of sulfate radical precursors (sodium persulfate, PDS) to the reaction environment did not give satisfactory effects (17% after 30 min), compared to the PDS/UV system (70% after 30 min). No rhodamine B decolorization was observed using hydrogen peroxide as a sole reagent, whereas an effect on the degree of RhB degradation was observed when UV rays strike the sample with H2O2 (33% after 30 min). The rhodamine B degradation process followed the pseudo-first-order kinetics model. The combined PDS/O3/UV process has shown 60% color removal after 30 min of reaction time at an initial dye concentration of 100 mg/L. A similar effectiveness was obtained by only applying ozone or UV-activated persulfate, but at a concentration 2–5 times lower (20 mg/L). The results indicated that the combined PDS/O3/UV process is a promising method for high RhB concentrations (50–100 mg/L) comparing to other alternative advanced oxidation processes.

Efficient removal of bisphenol S by non-radical activation of peroxydisulfate in the presence of nano-graphite

An environmentally friendly and efficient catalyst is important for the persulfate activation and pollutants removal from water. In this study, nano-graphite (NG) prepared by detonation method, was firstly applied as the superb carbon catalyst to activate peroxydisulfate (PDS) for the degradation of bisphenol S (BPS) via a non-radical pathway. Results showed that NG had a very high catalytic performance and degraded most of BPS within 20.0 min, out-performing many popular metal-based catalysts. The doped N atoms (i.e. graphitic N and pyridinic N) in NG were identified as the possible reactive sites for the PDS activation. It is proposed that PDS could form the metastable surface-bound PDS complexes on the NG surface, which promoted the BPS degradation. The NG/PDS system had a strong anti-interference ability for the environmental background substances and a wide operative pH range, so it had a good application prospect in the actual wastewater environment. This study not only provides an efficient method for the removal of bisphenol pollutants, but also deepens the insight into the reaction mechanisms.

Oily sludge derived carbons as peroxymonosulfate activators for removing aqueous organic pollutants: Performances and the key role of carbonyl groups in electron-transfer mechanism

In this work, low-cost carbon-based materials were developed via a facile one-pot pyrolysis of oily sludge (OS) and used as catalysts to activate peroxymonosulfate (PMS) for removing aqueous recalcitrant pollutants. By adjusting the pyrolysis temperature, the optimized OS-derived carbocatalyst manifested good performance for PMS activation to abate diverse organic pollutants in water treatment. Particularly, an average removal rate of 0.87 mol phenol per mol PMS per hour at a catalyst dosage of 0.2 g L^-1 is attained by the OS-derived carbocatalyst, higher than many other documented catalysts. A series of experimental evidences consolidated that organic pollutants were oxidized mainly via electron-transfer mechanism albeit the detection of singlet oxygen (¹O₂) from PMS activation driven by the OS-derived carbocatalyst. Specifically, the proportion of carbonyl groups (C˭O) in the carbocatalyst adopted with selective modification treatments to tailor the surface chemistry was found to be linearly correlated with the catalytic activity and theoretical calculations demonstrated that the reactions between C˭O and PMS to form surface reactive complexes were more energetically favorable compared to ¹O₂ generation. Herein, this study not only offers a new strategy for reusing OS as value-added persulfate activators but also deepens the fundamental understanding on the nonradical regime.

Sucrose-derived N-doped carbon xerogels as efficient peroxydisulfate activators for non-radical degradation of organic pollutants

Metal-free activation of peroxydisulfate (PDS) for degrading organic pollutants in water has received increasing attention because it can prevent secondary pollution. However, most of the catalysts that are efficient are derived from non-renewable fossil resources, are very expensive and have complex preparation processes. Also, the emerging non-radical mechanism is still unclear. Herein, 3D sucrose-derived N-doped carbon xerogels (NCXs) were synthesized by a simple and sustainable hydrothermal process and then employed as novel metal-free PDS activators to degrade organic pollutants. The structure, composition and performance of NCXs were regulated by changing the carbonization temperature. The sample carbonized at 900 °C (NCX900) exhibited the best catalytic performance, completely removing bisphenol A in 60 min. Quenching experiments and linear sweep voltammograms demonstrated that PDS was activated mainly through an electron-transfer non-radical mechanism. It was found that graphitic N played a critical role in activating PDS. With this non-radical mechanism, the NCX900/PDS system could adapt well to the wide pH range (3-11) and high Cl^- concentration; it selectively oxidized organic pollutants with low ionization potentials. This work provides a sustainable approach to the low-cost and efficient metal-free catalysts for wastewater treatment.

Carbon aerogel from forestry biomass as a peroxymonosulfate activator for organic contaminants degradation

The carbon catalyst has been widely used as a peroxymonosulfate (PMS) activator to degrade organic contaminants. The biomass carbon aerogel (CA) derived from poplar powder was synthesized in this study. CA with three-dimensional structure exhibited an excellent degradation performance of PMS activation for different types of organic contaminants including bisphenol A (BPA), rhodamine 6 G, phenol, and p-chlorophenol with the removal efficiencies up to 91%, 100%, 100%, and 60% within 60 min, respectively. It was found that singlet oxygen (¹O₂) dominated the non-radical pathway worked for BPA removal in CA/PMS system. The possible mechanism for PMS activation was discussed. A portion of ¹O₂ was produced through the transformation of superoxide radical (O₂^•-) in CA/PMS system. Electronic impedance spectroscopy (EIS) proved that the hierarchical structure of CA contributed to the electron transfer process for PMS activation. The ketonic/carbonyl groups (C˭O) on the surface of CA could serve as a possible active site to facilitate the generation of ¹O₂. In addition, CA showed superior degradation performance in actual water bodies and reusability with high-temperature regeneration treatment. This study developed an efficient and environmentally benign catalyst for water remediation of organic pollutants.

Redox cycling of copper mediated by hydrazine: efficient catalyst systems for oxidative degradation of rhodamine B

Catalytic processes based on Fenton-like reactions on the degradation of organic pollutants have been improved by accelerating the redox cycling of metal ions. This work presents, at first, the results obtained for the heterogeneous degradation of rhodamine B (RhB) by copper ferrite (CuFe₂O₄) in presence of hydrogen peroxide (H₂O₂) and hydrazine (N₂H₄) as redox cycle accelerator. Atomic absorption spectroscopy showed small amounts of Cu²⁺ are leached from ferrite highlighting the influence of the homogeneous catalysis in the whole process. The data obtained for the homogeneous process using Cu²⁺ in solution containing both N₂H₄ and H₂O₂ indicated such system is highly efficient mineralizing 73% of RhB within only 10 min of reaction and having H₂O and CO₂ as major products. Using tert-butyl alcohol as radical scavenger, it was confirmed hydroxyl radical (HO^•) is the active oxidant species regarding the RhB degradation. The homogeneous catalyst was applied to a real sample of textile effluent spiked with RhB and showed reasonable efficiency, although lower than that obtained for the standard solutions of RhB. This result was assigned to the interference of salts in the medium that react with HO^• thus acting as radical scavenger.

Selective oxidation and direct decolorization of cationic dyes by persulfate without activation

The aim of this work was to investigate the selective oxidation and direct decolorization of selected organic dyes (Methylene Blue (MB), Rhodamine B (RhB) and Orange II (OrgII)) by persulfate (PDS) without activation. Results show that the decolorization rate of MB was up to 58.0% within 10 minutes, while those of RhB and OrgII were only about 29.6% and 3.0% after 80 minutes, respectively. In comparison with the negligible impacts of pH from 2.0 to 9.0 on MB and OrgII decolorization, RhB decolorization rate obviously varied with the pH changes, and acid pH condition was beneficial for RhB decolorization. Quenching tests implied that the decolorization of dyes by PDS without activation was a nonradical oxidation process rather than sulfate radical oxidation. A plausible mechanism is that the decolorization process is attributed to the charged states of the dyes at different pH conditions, and thus direct electron transfer from dyes to PDS may occur, which is responsible for the bleaching of dyes. This study points out the potential bleaching capability of PDS without activation on cationic dyes, which may have important implications for selective oxidation treatment of dye wastewater.

One-step synthesis of mixed valence FeOX nanoparticles supported on biomass activated carbon for degradation of bisphenol A by activating peroxydisulfate

A novel FeO_X nanoparticles supported biomass activated carbon (BAC/FeO_X) composite was prepared through one-pot calcination method with FeCl₃ and cherry stone powder as precursors. The carbonization of biomass, reduction of Fe³⁺, and FeO_X anchored on carbon substrate could be achieved at the same time. Characterization with transmission electron microscope (TEM) and scanning electron microscope indicated that nanoscale FeO_X distributed uniformly on carbon substrate, and X-ray photoelectron spectroscopy, X-ray diffraction, and high resolution TEM characterization proved that the loaded FeO_X was high crystallinity of Fe₃O₄ and α-Fe⁰. Bisphenol A (BPA) was used to investigate the degradation performance of BAC/FeO_X activating peroxydisulfate (PDS). The ratio of raw materials affected degradation efficiency of BPA intensively through the content, valence state, and dispersibility of FeO_X nanoparticles, and the optimal material could degrade 20 mg/L BPA completely in 5 min at 0.1 g/L in the presence of 1 g/L PDS. Free radical determination and quenching experiments indicated that both SO₄^•- and •OH were involved in BPA degradation. The degradation pathway was proposed based on the identification of degradation intermediates. The facile synthesis method, high activation efficiency, and low-cost and environmental friendly raw materials made the BAC/FeO_X-50 an alternative catalyst for organic pollution water treatment.

Direct Z-scheme CeO2@LDH core-shell heterostructure for photodegradation of Rhodamine B by synergistic persulfate activation

Photocatalytic activation of persulfate (PAPS) is considered an efficient and green approach for the mitigation of organic pollutants because of its advantages in low energy consumption and high reusability of photocatalysts. Herein, direct Z-scheme CeO₂@LDH heterojunction photocatalyst with a core-shell structure is constructed. We reveal that CeO₂@LDH exhibits excellent persulfate (PS) activation performance and high degradation efficiency of RhB under visible light irradiation. Control experiments by quenching catalytically active radicals and analysis of electron paramagnetic resonance (ESR) spectra suggest that the sulfate radical (SO₄·^-) generated by photocatalytic activation of PS, together with superoxide radical (·O₂^-) and hydroxyl radical (·OH), degrade pollutants synergistically. Density functional theory (DFT) calculations indicate that the built-in electric field across the surface of CeO₂ and LDH is the intrinsic driving force for the efficient transfer of hot carriers in the Z-scheme heterojunction. The construction of this transfer path can effectively engineer the interfacial band structure and inhibit the recombination of photogenerated electron-hole pairs and promote their transportation. Meanwhile, electrons were found to accumulate at the conduction band (CB) of LDHs and holes populate at valence band (VB) of CeO₂, generating more active species for photodegradation of RhB. We demonstrate that the Z-scheme heterojunction photocatalyst activated PS system (Z-scheme/PS) is a promising method to degrade RhB and potentially organic pollutants in general.

Nonradicals induced degradation of organic pollutants by peroxydisulfate (PDS) and peroxymonosulfate (PMS): Recent advances and perspective

Nonradical persulfate oxidation processes have emerged as a new wastewater treatment method due to production of mild nonradical oxidants, selective oxidation of organic pollutants, and higher tolerance to water matrixes compared with radical persulfate oxidation processes. Since the case of the nonradical activation of peroxydisulfate (PDS) was reported on CuO surface in 2014, nonradical persulfate oxidation processes have been extensively investigated, and much achievement has been made on realization of nonradical persulfate activation processes and understanding of intrinsic reaction mechanism. Therefore, in the review, nonradical pathways and reaction mechanisms for oxidation of various organic pollutants by PDS and peroxymonosulfate (PMS) are overviewed. Five nonradical persulfate oxidation pathways for degradation of organic pollutants are summarized, which include surface activated persulfate, catalysts-free or catalysts mediated electron transfer, ¹O₂, high-valent metals, and newly derived inorganic oxidants (e.g., HOCl and HCO₄^-). Among them, the direct oxidation processes by persulfate, nonradical based persulfate activation by inorganic/organic molecules and in electrochemical methods is first overviewed. Moreover, nonradical based persulfate activation mechanisms by metal oxides and carbon materials are further updated. Furthermore, investigation methods of interaction between persulfate and catalyst surface, and nature of reactive species are also discussed in detail. Finally, the future research needs are proposed based on limited understanding on reaction mechanism of nonradical based persulfate activation. The review can offer a comprehensive assessment on nonradical oxidation of organic pollutants by persulfate to fill the knowledge gap and provide better guidance for future research and engineering application of persulfate.

Tin dioxide decorated on Ni-encapsulated nitrogen-doped carbon nanotubes for anodic electrolysis and persulfate activation to degrade cephalexin: Mineralization and degradation pathway

In this study, bamboo-shaped carbon nanotubes exhibiting high nitrogen content and Ni encapsulation (Ni@NCNT) were effectively synthesized by a simple pyrolysis method. The catalytic peroxydisulfate activation for cephalexin (CPX) degradation was investigated using the prepared material. SnO₂ was further decorated and fabricated on the anode material (SnO₂/Ni@NCNT) for electrochemical degradation of CPX in an aqueous solution. Transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy indicated that the SnO₂ nanoparticles were uniformly distributed on the surface of Ni@NCNT. Electrochemical characterization employing cyclic voltammetry and linear sweep voltammetry demonstrated that SnO₂/Ni@NCNT displayed higher oxygen evolution potential and electrocatalytic activity than Ni@NCNT. Mineralization of CPX in wastewater was performed using electrolysis coupled with persulfate oxidation. The analysis revealed a synergistic strengthening effect. The electropersulfate oxidation resulted in higher total organic carbon (TOC) removal (70.3%) than the sum of electrooxidation (48.1%) and persulfate oxidation (9.2%) toward CPX. This phenomenon might result from the regeneration of sulfate radicals (SO₄^•-) on the anode and complementary oxidation by SO₄^•- and OH. Persulfate oxidation alone was shown to result in low TOC removal, although CPX was mostly degraded. Additionally, the CPX degradation pathway involving electropersulfate oxidation was proposed and it is indicated that CPX molecules were completed decomposed by the examination of short chain acids, mineralized ions, and ecotoxicity evolution indicated that the antibiotic was completely degraded. This study provides a new approach for the design and preparation of novel electrode materials and electrochemical degradation facilities for the removal of pollutants via persulfate activation.

Evolution of Singlet Oxygen by Activating Peroxydisulfate and Peroxymonosulfate: A Review

Advanced oxidation processes (AOPs) based on peroxydisulfate (PDS) or peroxymonosulfate (PMS) activation have attracted much research attention in the last decade for the degradation of recalcitrant organic contaminants. Sulfate (SO₄^•−) and hydroxyl (^•OH) radicals are most frequently generated from catalytic PDS/PMS decomposition by thermal, base, irradiation, transition metals and carbon materials. In addition, increasingly more recent studies have reported the involvement of singlet oxygen (¹O₂) during PDS/PMS-based AOPs. Typically, ¹O₂ can be produced either along with SO₄^•− and ^•OH or discovered as the dominant reactive oxygen species (ROSs) for pollutants degradation. This paper reviews recent advances in ¹O₂ generation during PDS/PMS activation. First, it introduces the basic chemistry of ¹O₂, its oxidation properties and detection methodologies. Furthermore, it elaborates different activation strategies/techniques, including homogeneous and heterogeneous systems, and discusses the possible reaction mechanisms to give an overview of the principle of ¹O₂ production by activating PDS/PMS. Moreover, although ¹O₂ has shown promising features such as high degradation selectivity and anti-interference capability, its production pathways and mechanisms remain controversial in the present literatures. Therefore, this study identifies the research gaps and proposes future perspectives in the aspects of novel catalysts and related mechanisms.

ZIF-8 derived Fe‒N coordination moieties anchored carbon nanocubes for efficient peroxymonosulfate activation via non-radical pathways: Role of FeNx sites

Developing high-efficient hybrids carbon catalysts for PMS-based advanced oxidation process (AOPs) are crucial in the field of environmental remediation. In this work, novel carbon nanocubes (xFe‒N‒C) with three-dimensional porous structure and abundant well-dispersed FeN_x sites were obtained via a skillful cage-encapsulated-precursor pyrolysis strategy. The as-synthesized xFe‒N‒C exhibited superb activity for phenol degradation by activating peroxymonosulfate (PMS). Besides, the catalytic system not only possessed good recycling performance, wide pH adaptation and relatively low activation energy, but also had high resistance to environmental interference. Singlet oxygen (¹O₂) dominated non-radical process was responsible for phenol degradation rather than traditional radical pathways. Impressively, the doping level of Fe could regulate FeN_x contents in catalysts, and the catalytic activity of xFe‒N‒C was greatly enhanced with increasing FeN_x contents. Based on density functional theory calculations (DFT), the introduction of FeN_x sites regulated the electronic structure of catalysts. Such electron-deficient Fe center acted as electron acceptor to receive electrons transmitted by the adsorbed PMS, thus generating highly reactive ¹O₂ for rapid phenol oxidation. This work provides a new insight into the innovation in transition metal-nitrogen hybrid carbon catalysts and highlights the pivotal roles of FeN_x sites in ¹O₂ generation during PMS activation process.

Development of eco-friendly CO2-responsive cellulose nanofibril aerogels as "green" adsorbents for anionic dyes removal

A novel CO₂-responsive cellulose nanofibril aerogel as a "green" adsorbent derived from poly(methacrylic acid-co-2-(dimethylamino) ethyl methacrylate) and carboxylated cellulose nanofibrils was successfully prepared via stepwise cation-induced gelation and freeze drying method. This aerogel exhibited CO₂-triggered adsorption behavior towards anionic dyes with a rapid adsorption rate and a high adsorption capacity, as well as satisfactory mechanical properties. Upon CO₂ stimulation, the charged aerogel can selectively adsorb anionic dyes from aqueous solutions based on an electrostatic interaction. The maximum adsorption capacities of this aerogel towards methyl blue (MB), naphthol green B (NGB), and methyl orange (MO) were 598.8, 621.1 and 892.9 mg g^-1, respectively, accompanied by fast adsorption equilibriums towards MB and NGB within 7 min, and MO within 12 min. Meanwhile, the adsorption isotherms and the kinetics of the CO₂-responsive adsorbents followed the Freundlich isotherm and the pseudo-second-order model, respectively. Furthermore, the resulting CO₂-responsive adsorbent exhibited outstanding recyclability, as its adsorption performance can still be maintained even after twenty cycles. Accordingly, the resultant CO₂-responsive cellulose nanofibril aerogel could be a promising adsorbent material for the removal of anionic dyes in wastewater remediation.