Adsorptive removal of trace thallium(I) from wastewater: A review and new perspectives

Synthesis of porous carbon derived from coal tar residue via bimetallic salt activation for effective and selective adsorption of thallium(I)

As a highly toxic rare metal, the removal of thallium (Tl) from wastewater has been widely investigated, and adsorption is considered one of the most promising treatment technologies for Tl-containing contaminated water because of its cost-effectiveness, convenience, and high efficacy. In this work, coal tar residue (CTR)-based porous carbon was synthesized through K2FeO4 activation, and applied in adsorbing Tl(I). K2FeO4 could synergistically produce porosity and load iron oxide on the produced porous carbon surface because of the catalytic cracking and oxidative etching during the activation of CTR. The adsorbent was synthesized at 800 ℃ with a mass ratio of K2FeO4/CTR being 3 (PC3-800) showed optimal Tl(I) adsorption performance. The removal efficiency and distribution coefficient of PC3-800 were above 95 % and 104 mL/g, respectively, in a wide pH range (4-10). Furthermore, the selection and reusability of PC3-800 were favorable. The adsorption was a spontaneous, exothermic, and entropy increase process. The adsorption process was dominated by electrostatic attraction, surface complexation, and surface oxidation. The results suggested that removing Tl(I) from contaminated water via CTR-based porous carbon was feasible.

Enhanced removal of trace thallium by photo-promoted adsorption using Prussian blue@filter papers: Performance and mechanistic insights

Developing highly efficient adsorbents for the removal of trace thallium(I) (Tl+) is crucial for addressing environmental challenges. In this study, we successfully synthesized cubic Prussian blue (PB) loading on filter papers using an intermediate layer (dopamine/polyethyleneimine) via in-situ methods. The as-prepared PB-modified FP demonstrated outstanding anti-interference properties and light-enhanced adsorption performance for Tl+ (0.5 mg/L) under ultraviolet (UV) irradiation, exhibiting twice the effectiveness compared to dark conditions, even in acidic and coexisting ionic environments. This indicated its suitability for treating complex Tl+-contaminated water. Notably, the removal efficiency for trace Tl+ was almost 100%, with a maximum experimental adsorption capacity of 86.2 mg/g after 1-h photo-promoted adsorption under 365 nm UV. Characterization results supported a proposed photo-driven redox mechanism that elucidated the interaction between Tl+ and PB-modified FP. Specifically, the accelerated Fe(III) to Fe(II) redox reaction facilitated Tl+ accommodation on the surface and/or lattice of PB, enhancing Tl+ adsorption by compensating for missed positive charges. This study provides valuable insights into utilizing PB-based materials to enhance the photo-enhanced Tl+ adsorption capacity in a cost-effective, easy-to-synthesize, and environmentally friendly manner.

The determination of thallium in the environment: A review of conventional and advanced techniques and applications

Thallium (Tl) is a potential toxicity element that poses significant ecological and environmental risks. Recently, a substantial amount of Tl has been released into the environment through natural and human activities, which attracts increasing attention. The determination of this hazardous and trace element is crucial for controlling its pollution. This article summarizes the advancement and progress in optimizing Tl detection techniques, including atomic absorption spectroscopy (AAS), voltammetry, inductively coupled plasma (ICP)-based methods, spectrophotometry, and X-ray-based methods. Additionally, it introduces sampling and pretreatment methods such as diffusive gradients in thin films (DGT), liquid-liquid extraction, solid phase extraction, and cloud point extraction. Among these techniques, ICP-mass spectrometry (MS) is the preferred choice for Tl detection due to its high precision in determining Tl as well as its species and isotopic composition. Meanwhile, some new materials and agents are employed in detection. The application of novel work electrode materials and chromogenic agents is discussed. Emphasis is placed on reducing solvent consumption and utilizing pretreatment techniques such as ultrasound-assisted processes and functionalized magnetic particles. Most detection is performed in aqueous matrices, while X-ray-based methods applied to solid phases are summarized which provide non-destructive analysis. This work improves the understanding of Tl determination technology while serving as a valuable resource for researchers seeking appropriate analytical techniques.

Understanding the role of manganese oxides in retaining harmful metals: Insights into oxidation and adsorption mechanisms at microstructure level

The increasing intensity of human activities has led to a critical environmental challenge: widespread metal pollution. Manganese (Mn) oxides have emerged as potentially natural scavengers that perform crucial functions in the biogeochemical cycling of metal elements. Prior reviews have focused on the synthesis, characterization, and adsorption kinetics of Mn oxides, along with the transformation pathways of specific layered Mn oxides. This review conducts a meticulous investigation of the molecular-level adsorption and oxidation mechanisms of Mn oxides on hazardous metals, including adsorption patterns, coordination, adsorption sites, and redox processes. We also provide a comprehensive discussion of both internal factors (surface area, crystallinity, octahedral vacancy content in Mn oxides, and reactant concentration) and external factors (pH, presence of doped or pre-adsorbed metal ions) affecting the adsorption/oxidation of metals by Mn oxides. Additionally, we identify existing gaps in understanding these mechanisms and suggest avenues for future research. Our goal is to enhance knowledge of Mn oxides' regulatory roles in metal element translocation and transformation at the microstructure level, offering a framework for developing effective metal adsorbents and pollution control strategies.

Separation of lead-212 from natural thorium solution utilizing novel sulfonamide dibenzo-18-crown-6

The extraction of lead-212 (212Pb) from radioactive thorium (Th) waste is immensely important, as it serves to mitigate environmental risks associated with radioactive waste and provides a vital source for medical isotopes. To economically extract 212Pb from thorium, we synthesized a novel extractant known as 2,13-disulfonyldiethylamine dibenzo-18-crown-6 (DSADB18C6). We assessed its performance in isolating Pb(II) by employing stable lead and optimizing the parameters of the extraction system. The results showcased an exceptional ability to extract Pb(II) efficiently. Within 10 minutes, using 20 mmol of DSADB18C6 and under conditions of 10 mg L-1 lead concentration (HNO3 = 0.5 mol L-1), the extraction efficiency reached up to 96.1%. Even after four rounds of stripping with 0.4 mol L-1 ammonium citrate, the efficiency remained at 90.2%. Moreover, the extraction stoichiometry and thermodynamics revealed that DSADB18C6 exhibited superior extraction performance compared to the commercial extractant 4',4'',(5'')-di-(tert-butyldicyclohexano)-18-crown-6 (DtBuDC18C6), in line with the density functional theory (DFT) calculation result. Furthermore, we successfully separated 212Pb from the thorium nitrate solution, maintaining radioactive equilibrium with its progeny. Gamma-spectroscopy confirmed a recovery yield of extraction exceeding 85.7%. This study presents a viable approach, underscoring the potential of DSADB18C6 as a promising extractant for the effective separation of 212Pb from radioactive thorium sources.

Mechanisms for thallium(I) adsorption by zinc sulfide minerals under aerobic and anaerobic conditions

The highly toxic heavy metal thallium is widely distributed in sulfide ores and released into the environment by sulfide mining. However, the interface between the sulfide minerals and Tl(I) is unclear. In this study, the capacity for adsorption of thallium(I) by a common sulfide mineral (zinc sulfide) was investigated in aerobic and anaerobic environments, which revealed three mechanisms for adsorption on the ZnS surface (surface complexation, electrostatic action and oxidation promotion). Batch experiments indicated that the Tl(I) adsorption capacity of ZnS in an aerobic environment was approximately 9.3% higher than that in an anaerobic environment and was positively correlated with the pH. The adsorption kinetic data showed good fits with the pseudosecond-order model and the Freundlich isotherm model. The Tl(I) adsorption mechanism varied in different oxidative and pH environments. XPS, FTIR, and EDS results implied that complexation with surface hydroxyl groups was involved in the adsorption process. pH experiments and zeta analyses suggested that electrostatic attraction was also involved. Surface complexation and electrostatic attraction were the dominant mechanisms at pH values above 6. Furthermore, oxidative dissolution of ZnS and hydrolysis of Zn2+ enhanced the complexation with hydroxyl groups on the mineral surface and facilitated Tl adsorption. In this study, this interface mechanism provided new insights into thallium migration in sulfurized mineral environments in aerobic and anaerobic transition regions.

An eco-friendly composite hydrogel based on covalently crosslinked cellulose/poly (glycerol citrate) for thallium (Ι) removal from aqueous solutions

Cellulose/poly (glycerol citrate) reinforced with thiol-rich polyhedral oligomeric silsesquioxane and apple peel (POSS-SH@CAG-CEL/AP) was synthesized using gelation method in the presence of glutaraldehyde as a crosslinker agent and used as an efficient composite hydrogel for elimination of Tl(Ι) from aqueous solutions. This composite hydrogel and synthesized thiol-rich polyhedral oligomeric silsesquioxane were characterized by elemental analysis, FT-IR, NMR, TGA, and FE-SEM techniques. The effects of synthetic and environmental parameters on the adsorption capacity of the composite hydrogel were investigated and it was found that thiol-rich polyhedral oligomeric silsesquioxane has improved the hydrogel properties including the Tl(Ι) uptake and the thermal stability. The maximum adsorption capacity of 352.3 mg g-1 was obtained within 30 min under optimum reaction conditions. A typical Langmuir adsorption isotherm with was observed for adsorption of Tl(I) onto POSS-SH@CAG-CEL/AP and pseudo-second-order kinetic model provided the best correlation between experimental data. Thermodynamic studies showed that the Tl(I) adsorption was spontaneous process and exothermic. Also, the reusability tests confirmed that the POSS-SH@CAG-CEL/AP can be reused for four times without any remarkable change in its adsorption capacity. Thus, this reusable biobased composite hydrogel can be an ideal candidate for elimination of Tl(I) from aqueous solutions.

Remediation potential of mining, agro-industrial, and urban wastes against acid mine drainage

Acid mine drainage (AMD) poses serious consequences for human health and ecosystems. Novel strategies for its treatment involve the use of wastes. This paper evaluates the remediation potential of wastes from urban, mining and agro-industrial activities to address acidity and high concentrations of potentially toxic elements (PTE) in AMD. Samples of these waste products were spiked with an artificially prepared AMD, then pH, electrical conductivity (EC), and PTE concentrations in the leachates were measured. The artificial AMD obtained through oxidation of Aznalcóllar's tailing showed an ultra-acid character (pH - 2.89 ± 0.03) and extreme high electrical conductivity (EC - 3.76 ± 0.14 dS m^-1). Moreover, most PTE were above maximum regulatory levels in natural and irrigation waters. Wastes studied had a very high acid neutralising capacity, as well as a strong capacity to immobilise PTE. Inorganic wastes, together with vermicompost from pruning, reduced most PTE concentrations by over 95%, while organic wastes retained between 50 and 95%. Thus, a wide range of urban, mining, and agro-industrial wastes have a high potential to be used in the treatment of AMD. This study provides valuable input for the development of new eco-technologies based on the combination of wastes (eg. Technosols, permeable reactive barriers) to remediate degraded environments.

Sequestration and oxidation of heavy metals mediated by Mn(II) oxidizing microorganisms in the aquatic environment

Microorganisms can oxidize Mn(II) to biogenic Mn oxides (BioMnOx), through enzyme-mediated processes and non-enzyme-mediated processes, which are generally considered as the source and sink of heavy metals due to highly reactive to sequestrate and oxidize heavy metals. Hence, the summary of interactions between Mn(II) oxidizing microorganisms (MnOM) and heavy metals is benefit for further work on microbial-mediated self-purification of water bodies. This review comprehensively summarizes the interactions between MnOM and heavy metals. The processes of BioMnOx production by MnOM has been firstly discussed. Moreover, the interactions between BioMnOx and various heavy metals are critically discussed. On the one hand, modes for heavy metals adsorbed on BioMnOx are summarized, such as electrostatic attraction, oxidative precipitation, ion exchange, surface complexation, and autocatalytic oxidation. On the other hand, adsorption and oxidation of representative heavy metals based on BioMnOx/Mn(II) are also discussed. Thirdly, the interactions between MnOM and heavy metals are also focused on. Finally, several perspectives which will contribute to future research are proposed. This review provides insight into the sequestration and oxidation of heavy metals mediated by Mn(II) oxidizing microorganisms. It might be helpful to understand the geochemical fate of heavy metals in the aquatic environment and the process of microbial-mediated water self-purification.

Highly inhibited transport of dissolved thallium(I) in manganese oxide-coated sand: Chemical condition effects and retention mechanisms

Thallium contamination in water can cause great danger to the environment. In this study, we synthesized manganese oxide-coated sand (MOCS) and investigated the transport and retention behaviors of Tl(I) in MOCS under different conditions. Characterization methods combined with a two-site nonequilibrium transport model were applied to explore the retention mechanisms. The results showed that Tl(I) mobility was strongly inhibited in MOCS media, and the retention capacity calculated from the fitted model was 510.41 mg/g under neutral conditions. The retention process included adsorption and oxidative precipitation by the manganese oxides coated on the sand surface. Cotransport with the same concentration of Mn(II) led to halving Tl(I) retention due to competition for reactive sites. Enhanced Tl(I) retention was observed under alkaline conditions, as increasing pH promoted electronegativity on the media surface. Moreover, the competitive cation Ca²⁺ significantly weakened Tl(I) retention by occupying adsorption sites. These findings provide new insights into understanding Tl(I) transport behavior in water-saturated porous media and suggest that manganese oxide-coated sand can be a cost-effective filter media for treating Tl-contaminated water.

Release and mobility characteristics of thallium from polluted farmland in varying fertilization: Role of cation exchange

Batch and column leaching tests were used to study thallium's release and migration behaviour and evaluate its potential toxicity risks in soil. The results indicated that leaching concentrations of Tl using TCLP and SWLP were much higher than the threshold, indicating a high risk of thallium pollution in the soil. Furthermore, the intermittent leaching rate of Tl by Ca²⁺ and HCl reached its maximum value, demonstrating the easy release of Tl. After HCl leaching, the form of Tl in the soil has changed, and ammonium sulfate has increased its extractability. Additionally, the extensive application of calcium promoted the release of Tl, increasing its potential ecological risk. Spectral analysis showed that Tl was mainly present in minerals such as Kaolinite and Jarosite, and exhibited significant adsorption capacity for Tl. HCl and Ca²⁺ damaged the crystal structure of the soil, greatly enhancing the migration and mobility of Tl in the environment. More importantly, XPS analysis confirmed that the release of Tl (I) in the soil was the leading cause of increased mobility and bioavailability. Therefore, the results revealed the risk of Tl release in the soil, providing theoretical guidance for its pollution prevention and control.

Activated carbon enhanced traditional activated sludge process for chemical explosion accident wastewater treatment

With the development of industries, explosion accidents occur frequently during production, transportation, usage and storage of hazard chemicals. It remained challenging to efficiently treat the resultant wastewater. As an enhancement of traditional process, the activated carbon-activated sludge (AC-AS) process has a promising potential in treating wastewater with high concentrations of toxic compounds, chemical oxygen demand (COD) and ammonia nitrogen (NH₄⁺-N), etc. In this paper, activated carbon (AC), activated sludge (AS) and AC-AS were used to treat the wastewater produced from an explosion accident in the Xiangshui Chemical Industrial Park. The removal efficiency was assessed by the removal performances of COD, dissolved organic carbon (DOC), NH₄⁺-N, aniline and nitrobenzene. Increased removal efficiency and shortened treatment time were achieved in the AC-AS system. To achieve the same COD, DOC and aniline removal (90%), the AC-AS system saved 30, 38 and 58 h compared with the AS system, respectively. The enhancement mechanism of AC on the AS was explored by metagenomic analysis and three-dimensional excitation-emission-matrix spectra (3DEEMs). More organics, especially aromatic substances were removed in the AC-AS system. These results showed that the addition of AC promoted the microbial activity in pollutant degradation. Bacteria, such as Pyrinomonas, Acidobacteria and Nitrospira and genes, such as hao, pmoA-amoA, pmoB-amoB and pmoC-amoC, were found in the AC-AS reactor, which might have played important roles in the degradation of pollutants. To sum up, AC might have enhanced the growth of aerobic bacteria which further improved the removal efficiency via the combined effects of adsorption and biodegradation. The successful treatment of Xiangshui accident wastewater using the AC-AS demonstrated the potential universal characteristics of the process for the treatment of wastewater with high concentration of organic matter and toxicity. This study is expected to provide reference and guidance for the treatment of similar accident wastewaters.

Dynamic retention of thallium(I) on humic acid: Novel insights into the heterogeneous complexation ability and responsiveness

Widely distributed soil humic acid (HA) would significantly affect the environmental migration behavior of Tl(I), but a quantitative and mechanistic understanding of the dynamic Tl(I) retention process on HA is limited. A unified kinetic model was established by coupling the humic ion-binding model with a stirred-flow kinetic model, which quantified the complexation constants and responsiveness coefficients during dynamic Tl(I)-HA complexation. Furthermore, the heterogeneous complexation mechanism of HA and Tl(I) was revealed by batch adsorption experiments, stirred-flow migration experiments, and 2D-FTIR-COS analysis. An increase in pH significantly improved the responsiveness of HA organic binding sites, promoting Tl(I) dynamic retention. Monodentate carboxyl groups induced rapid Tl(I) complexation (k_d = 1.9 min^-1) in strongly acidic environments. Under weakly acidic conditions, Tl(I) retention on HA was mainly attributed to the synergistic complexation effect of carboxyl and amide groups. Among the groups, multidentate carboxyl-phenolic hydroxyl sites could achieve sustained Tl(I) retention due to their stable complexing properties (logK = 4.48∼7.46) and slow response (k_d = 1.1 × 10^-3 min^-1). These findings are crucial for a comprehensive understanding of the environmental interactions of Tl(I) with humic substances in swamp environments.

Versatile Magnetic Mesoporous Carbon Derived Nano-Adsorbent for Synchronized Toxic Metal Removal and Bacterial Disinfection from Water Matrices

Contamination of water resources by toxic metals and opportunistic pathogens remains a serious challenge. The development of nano-adsorbents with desired features to tackle this problem is a continuously evolving field. Here, magnetic mesoporous carbon nanospheres grafted by antimicrobial polyhexamethylene biguanidine (PHMB) are reported. Detailed mechanistic investigations reveal that the electrostatic stabilizer modified magnetic nanocore interfaced mesoporous shell can be programmatically regulated to tune the size and related morphological properties. The core-shell nano-adsorbent shows tailorable shell thickness (≈20-55 nm), high surface area (363.47 m² g^-1 ), pore volume (0.426 cm³ g^-1 ), radially gradient pores (11.26 nm), and abundant biguanidine functionality. Importantly, the nano-adsorbent has high adsorption capacity for toxic thallium (Tl(I) ions (≈559 mg g^-1 ), excellent disinfection against Staphylococcus aureus and Escherichia coli (>99.99% at 2 and 2.5 µg mL^-1 ), ultrafast disinfection kinetics rate (>99.99% within ≈4 min), and remarkable regeneration capability when exposed to polluted water matrices. The Tl(I) removal is attributed to surface complexation and physical adsorption owing to open ended mesopores, while disinfection relies on contact of terminal biguanidines with phospholipid head groups of membrane. The significance of this work lies in bringing up effective synchronic water purification technology to combat pathogenic microorganisms and toxic metal.

Thallium removal from wastewater using sulfidized zero-valent manganese: Effects of sulfidation method and liquid nitrogen pretreatment

Zero-valent manganese (ZVMn) possesses high reducibility in theory, while sulfide exhibits strong affinity towards a variety of heavy metals owing to the low solubility of metal sulfides. Yet the performance and mechanisms on using sulfidized zero-valent manganese (SZVMn) to remove thallium (Tl) from wastewater still remain unclear. In this study, the performance of Tl(I) removal using SZVMn synthesized by borohydrides reduction followed by sulfides modification, with and without liquid nitrogen treatment, was compared and the mechanism behind was investigated. The results show that at a S/Mn molar ratio of 1.0, liquid nitrogen modified SZVMn (LSZVMn) possessed more interior channels and pores than SZVMn, with 65.3% higher specific surface area and 73.7% higher porosity, leading to 6.4-8.1% improvement in adsorption of Tl(I) at pH 4-10. LSZVMn showed effectiveness and robustness in Tl(I) removal in the presence of co-existing ions up to 0.1 M. The adsorption of Tl(I) conformed to the pseudo-1st-order kinetic model, and followed the Langmuir isothermal model, with the maximum Tl adsorption capacity of 264.9 mg·g^-1 at 288 K. The mechanism of Tl(I) removal with SZVMn was found to include sulfidation-induced precipitation, manganese reduction, surface complexation, and electrostatic attraction. The liquid nitrogen pretreatment embrittled and cracked the outer shell of S/Mn compounds, resulted in a highly hierarchical structure, enhancing the manganese reduction and improving the Tl(I) removal. Based on the above results, the SZVMn and its liquid nitrogen-modified derivatives are novel and effective environmental materials for Tl(I) removal from wastewater, and the application of SZVMn to the removal of other pollutants merits investigation in future study.

Recent Advances in Thallium Removal from Water Environment by Metal Oxide Material

Thallium is widely used in industrial and agricultural development. However, there is still a lack of systematic understanding of its environmental hazards and related treatment methods or technologies. Here, we critically assess the environmental behavior of thallium in aqueous systems. In addition, we first discuss the benefits and limitations of the synthetic methods of metal oxide materials that may affect the practicality and scalability of TI removal from water. We then assess the feasibility of different metal oxide materials for TI removal from water by estimating the material properties and contaminant removal mechanisms of four metal oxides (Mn, Fe, Al, and Ti). Next, we discuss the environmental factors that may inhibit the practicality and scalability of Tl removal from water. We conclude by highlighting the materials and processes that could serve as more sustainable alternatives to TI removal with further research and development.

Hotspots analysis and perspectives of Prussian blue analogues (PBAs) in environment and energy in recent 20 years by CiteSpace

Prussian blue analogs (PBAs), a type of metal-organic frameworks (MOFs), have attracted much attention because of their large specific surface area, high porosity, easy synthesis, and low cost. This paper presents the first review of PBAs by applying the bibliometric visualization software CiteSpace. The co-occurrence, co-citation, and clustering analysis of 2214 articles in the Web of Science database on the topic of "Prussian blue analogs" over the past 20 years were performed. The results provide a comprehensive overview of the evolution of the research hotspots for this material, and most importantly, it is identified that the research hotspots and trends for PBAs materials are concentrated in the environmental and energy fields. For example, the material is used as an adsorbent or catalyst to reduce pollutants, produce clean energy, or for energy storage applications such as batteries or supercapacitors. Finally, some outlooks are provided on the future research trends of this material in the environmental and energy fields, presenting the challenges faced by this material. For instance, the conductivity and corrosion resistance of the material needs to be improved and secondary contamination should be decreased or even avoided. It is believed that this paper would provide a comprehensive, systematic, and dynamic overview of the research of PBAs, and promote the future research of PBAs in the fields of environment and energy.

Impact of the Syn/Anti Relative Configuration of Cryptophane-222 on the Binding Affinity of Cesium and Thallium

We report in this article the synthesis, the X-ray crystal structure of compound syn-2, and its binding properties with cesium and thallium in aqueous solution under basic conditions. Compound syn-2 is the diastereomeric compound of anti-1 that shows very high affinity for cesium and thallium in aqueous solution under the same conditions. Despite the close structural similarities that exist between the syn-2 and anti-1 compounds, they show large discrepancy in their ability to bind cesium and thallium cations in the same conditions. Indeed, the syn-2 derivative has a lower affinity for these two cationic species and the binding constants are several orders of magnitude lower than those found for its congener. The large differences in affinity observed with these two compounds can be explained by the relative position of the six hydroxyl groups to each other.

Efficient Adsorption of Tl(I) from Aqueous Solutions Using Al and Fe-Based Water Treatment Residuals

Iron and aluminum water treatment residuals from a water supply plant were used as adsorbents for Tl(I) to treat thallium-containing Tl(I) wastewater and realize the resource utilization of water treatment residuals. The feasibility study results showed that Fe-WTR and Al-WTR reached adsorption equilibria within 120 min. The Langmuir model showed maximum adsorption capacities of Tl(I) on Fe-WTR and Al-WTR as 3.751 and 0.690 mg g−1 separately at an initial concentration of 5 mg L−1. The adsorption capacities of Fe-WTR and Al-WTR positively correlated with pH. The removal of Tl(I) using Fe-WTR exceeded Al-WTR; the adsorbed Tl(I) in Fe-WTR occurred primarily in the reduced state, while the Tl(I) adsorbed in Al-WTR was mainly in acid-extractable and reduced states. FTIR and XPS data showed that Tl(I) and Fe/Al-OH-functional groups formed stable surface complexes (Fe/Al-O-Tl) during adsorption, and there was no redox reaction. This confirmed that WTR is a highly efficient adsorbent for the stable removal of Tl(I), which provides a practical foundation for industrial application in Tl(I)-containing wastewater treatment.

Perspective on Fe0-PS synergetic effect and reaction mechanism in the thallium(I) contaminated water treatment

Due to extreme toxicity of the element of thallium (Tl), increasing aqueous Tl pollution incidents have aroused growing concerns. As the prevalent and stable form, i.e., monovalent Tl, the highly efficient removal methodologies of Tl(I) from (waste)water remains limited and challenging. In this study, an advanced oxidation method, the feasibility of using zero valent iron (Fe⁰) coupled with persulfate (PS) to treat Tl(I)-containing synthetic wastewater was investigated. Its influence parameters, including reaction time, initial Tl concentration, dosages of PS and Fe⁰, initial and coagulation pH, temperature, coexisting ions and organic matter (NO₃^-, SO₄^2-, Cl^- and HA) were examined. The results revealed that the system can be applied to a wide range of pH and temperature and the reaction equilibrium can be reached in about 30 min. Favorable Tl(I) removal rate (>98%) was observed in the synthetic wastewater with medium and relatively high Tl(I) concentration (≤0.250 mM). The analyses of characterization results including electron spin resonance spectrometer and X-ray photoelectron spectroscopy indicated that ·OH played a vital role in the removal of Tl(I), which was oxidized and removed by co-precipitation. Fe⁰ can be served as a stable source of Fe²⁺ to efficiently catalyze PS. The remaining Fe⁰ can be easily separated because of its magnetism, assuring the promising reusability of the reactant. The study aims to provide references for treatment of real Tl polluted wastewater.

Removal of Thallium from Aqueous Solutions by Adsorption onto Alumina Nanoparticles

Thallium (I) was removed from aqueous solution by using gamma-alumina nanoparticles (γANPs) materials as nano adsorbents. Varied experimental conditions such as adsorbent dose, agitation time, initial concentration, pH, and temperature effects were carried out in batch conditions in view of the optimization of thallium (I) adsorption and the identification of the adsorption mechanisms in the system γANPs-Tl. The pH effect indicated a remarkable increase in the quantity of Tl(I) removed for pH values ranging from 4 to 8, an almost constant magnitude for pH values between 8 and 10, and a decrease for pH values above 10. Considering an initial Tl(I) concentration of 20 µg/L and an adsorbent dose of 1 g/L at a pH value of 8.5, the removal was achieved at 95.12 ± 0.02% efficiency. The pseudo-second-order kinetics and the Freundlich isotherm perfectly described the adsorption mechanism. The process of thallium (I) adsorption reaction, as highlighted by thermodynamic investigations, was found to be spontaneous and exothermic with coexistence of physisorption and chemisorption with a dominance of physisorption. The diffusion model predicted multi-linearity, suggesting an involvement of surface spread and intraparticle diffusion in the sorption process. Thallium removal was effective by using γANPs as nano adsorbents.

Arsenic in drinking water: overview of removal strategies and role of chitosan biosorbent for its remediation

Accessibility to clean drinking water often remains a crucial task at times. Among other water pollutants, arsenic is considered a more lethal contaminant and has become a serious threat to human life globally. This review discussed the sources, chemistry, distribution, and toxicity of arsenic and various conventional technologies that are in option for its removal from the water system. Nowadays, biosorbents are considered the best option for arsenic-contaminated water treatment. We have mainly focused on the need and potential of biosorbents especially the role of chitosan-based composites for arsenic removal. The chitosan-based sorbents are economically more efficient in terms of their, low toxicity, cost-effectiveness, biodegradability, eco-friendly nature, and reusability. The role of various modification techniques, such as physical and chemical, has also been evaluated to improve the physicochemical properties of biosorbent. The importance of adsorption kinetic and isotherm models and the role of solution pH and pH_PZC for arsenic uptake from the polluted water have also been investigated. Some other potential applications of chitosan-based biosorbents have also been discussed along with its sustainability aspect. Finally, some suggestions have been highlighted for further improvements in this field.

New Approach for Trace Thallium Removal in High Purity Ammonium Rhenate Solution by P204 Extraction

Thallium (Tl) is an extremely toxic rare metal to the eco-environment. Trace thallium impurity in ammonium perrhenate is harmful to the high-temperature mechanical properties of rhenium metal used for aeroengine single crystal blade. The di(2-ethylhexyl) phosphoric acid (P204) extraction to remove thallium in ammonium perrhenate solution without additive was innovatively proposed. The migration behavior of trace thallium with the concentration of P204, saponification degree and organic/aqueous phase (O/A) ratio, distribution law of thallium in the extraction system of P204, and mechanism of thallium removal were revealed. It was found Tl removal was rapidly increased to 98.5%, at conditions of P204 0.75 mol/L saponified 70% by ammonia, Tl 3.27 mg/L, O/A 1:1, T 298.15 ± 2 K, 250 rpm, and 3 min. McCabe-Thiele Tl extraction equilibrium isotherms indicates Tl concentration of raffinate less than 18.7 μg/L, a theoretical extraction of two stages and a theoretical stripping of two stages are required when both O/A work lines were at 1.0. Therefore, the method of the P204 solvent extraction system can effectively extract Tl in the forms of TlA(org), TlA3(org), TlOHA2(org), and Tl(OH)2A(org). Meanwhile, the new approach can be a promising process for ammonium rhenate refining.

Insights into the synergistic removal mechanisms of thallium(I) by biogenic manganese oxides in a wide pH range

The behavior and mechanism of thallium (Tl) adsorption by biogenic manganese oxides (BMnOx) are poorly understood. In this study, BMnOx was applied for Tl(I) removal from aqueous solution, and the adsorption interactions were systematically revealed for the first time. BMnOx was successfully prepared with high productivity by effectively oxidizing Mn(II) with a manganese oxide bacterium in an optimal Mn(II) concentration range of 4.0-28 mg/L. Compared with other adsorbents, the prepared BMnOx achieved high Tl(I) adsorption capacity over a wide pH range from 3.0 to 9.0 and high humic acid (HA) concentration (40 mg/L) interference. The experimental results were well depicted by pseudo-second-order kinetics and the Langmuir isotherm model, indicating that chemisorption played the dominant role during the adsorption process. The adsorption mechanisms were verified as synergetic interactions of oxidation-precipitation, electrostatic attraction, ion exchange and surface complexation. X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) results suggested that 19.46% of the highly toxic Tl(I) was transformed into the much less toxic product Tl₂O₃ after adsorption onto BMnOx. This study provides theoretical guidance for high-concentration Tl(I) decontamination from groundwater by biogenic manganese oxides.

Thallium and potentially toxic elements distribution in pine needles, tree rings and soils around a pyrite mine and indication for environmental pollution

In this study, the distributions of thallium (Tl), and other potential toxic elements, such as Cd, Co, Cu, Pb, Sr, As, Cr, Ni, Zn, and Mn in needles, tree rings and soils of pine trees in one of the largest pyrite mining areas in the world, i.e., Yunfu, China were investigated. The results showed that pseudo-total Tl concentration of the tree rings ranged from 0.41 to 2.03 mg/kg (average: 1.12 mg/kg) during the year of 1998 to 2011. This indicates an overall obvious enrichment of Tl. Further investigation of element level variations in the pine needles showed a negative correlation between Tl content and the distance from the mining area. The results of Principal Component Analysis additionally demonstrated that Tl in the tree rings was most likely derived from the pine needles. Notably, Tl contents in the tree rings exhibited generally similar distribution pattern to the annual production intensity of Yunfu pyrite mining activities. The findings suggest that metal(loid)s in particular of Tl in pine tree rings can be used as alternative proxies to approximatively reconstruct the chronological change of atmospheric environmental pollution induced by pyrite associated mining/smelting activities.

A fundamental study on selective extraction of Li+ with dibenzo-14-crown-4 ether: Toward new technology development for lithium recovery from brines

The present study has proposed a selective Li⁺ extraction process using a novel extractant of dibenzo-14-crown-4 ether functionalized with an alkyl C16 chain (DB14C4-C16) synthesized based on the ion imprinting technology (IIT). Theoretical analysis of the possible complexes formed by DB14C4-C16 with Li⁺ and the competing ions of Na⁺, K⁺, Ca²⁺ and Mg²⁺ was performed through density functional theory (DFT) modeling. The Gibbs free energy change of the complexes of metal ions with DB14C4-C16 and water molecules were calculated to be -125.81 and -166.01 kJ/mol for lithium, -55.73 and -117.77 kJ/mol for sodium, and -196.02 and -291.52 kJ/mol for magnesium, respectively. Furthermore, the solvent extraction experiments were carried out in both single Li⁺ and multi-ions containing solutions, and the results delivered a good selectivity of DB14C4-C16 towards Li⁺ over the competing ions, showing separation coefficients of 68.09 for Ca²⁺-Li⁺, 24.53 for K⁺-Li⁺, 16.32 for Na⁺-Li⁺, and 3.99 for Mg²⁺-Li⁺ under the optimal conditions. The experimental results are generally in agreement with the theoretical calculations.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Trace elements in whole blood in the general population in Trøndelag County, Norway: The HUNT3 Survey

BACKGROUND

Biomonitoring of a cohort within a large health survey can provide reliable information on trace element status. The main aims of this study were 1) to determine the concentrations of 28 trace elements in whole blood samples from the general population of the Nord-Trøndelag region, Norway, and 2) to investigate how trace element concentrations vary with geographical area, lifestyle, and socio-demographic factors.

METHODS

Whole blood samples were collected in the third survey of the Trøndelag Health Survey (HUNT3), a large population-based study in Norway. In total, 1011 whole blood samples from individuals aged 20-91 years were analyzed using high resolution inductively coupled plasma-mass spectrometry (HR-ICP-MS). We compared trace element concentrations (As, B, Be, Br, Ca, Cd, Cr, Cs, Cu, Ga, Au, In, Fe, Pb, Hg, Tl, Mg, Mn, Mo, Ni, Rb, Sc, Se, Ag, Sr, Sn, W and Zn) between three geographical areas (coastal, fjord/town, inland/mountain) using multivariable linear regression and assessed differences in trace element concentrations with socio-demographic and lifestyle factors using general linear models.

RESULTS

Trace element concentrations were generally comparable to levels reported in other recent studies and suggest low exposure to toxic trace elements in the region. We found geographical differences in concentrations of 19 trace elements. As, Br, Hg, and Se concentrations were higher on the coast compared to the fjord/town and inland/mountain areas, suggesting that the marine environment is an important source of exposure for these trace elements. In addition, socio-demographic and lifestyle characteristics, particularly age and sex, were associated with differences in trace element concentrations.

CONCLUSIONS

We report concentrations of 28 trace elements in the general population of a rural region with low exposure to pollution. Whole blood concentrations of trace elements varied with geographical area, the participants' lifestyle, and socio-demographic characteristics, highlighting the importance of considering these factors when evaluating trace element status in a population.

Highly efficient removal of thallium(I) by facilely fabricated amorphous titanium dioxide from water and wastewater

In this study, amorphous hydrous titanium dioxide was synthesized by a facile precipitation method at room temperature, aiming to effectively remove thallium(I) from water. The titanium dioxide prepared using ammonia as precipitant (TiO2I) is more effective for thallium(I) uptake than the one synthesized with sodium hydroxide (TiO2II). The TiO2 obtained particles are amorphous, aggregates of many nanoparticles and irregular in shape. The thallium(I) uptake increases with the rise of solution pH value. Under neutral pH conditions, the maximal thallium(I) adsorption capacities of TiO2I and TiO2II are 302.6 and 230.3 mg/g, respectively, outperforming most of the reported adsorbents. The amorphous TiO2 has high selectivity towards thallium(I) in the presence of multiple cations such as K+, Ca2+, Mg2+, Zn2+ and Ni2+. Moreover, the TiO2I is efficient in removing thallium(I) from real river water and mining wastewater. Additionally, the spent TiO2I can be regenerated using hydrochloric acid solution and reused. The Tl(I) adsorption is achieved via replacing the H+ in hydroxyl group on the surface of TiO2 and forming inner-sphere surface complexes. Owing to its high efficiency, facile synthesis and environmental friendliness, the TiO2I has the potential to be used as an alternative adsorbent to remove Tl(I) from water.

A review of polyampholytic ion scavengers for toxic metal ion removal from aqueous systems

Pollution by heavy metal ions in aqueous systems gained researchers attention gradually. Toxic metal ions were always present in the environment and the living organisms could get used to specific concentrations of contaminants with given time, however, sudden concentration rise we are observing can make it impossible for the living organisms to adapt. Many ion removal technologies were developed and optimised over the years to cope with this problem, including chemical precipitation, adsorption, membrane filtration and ion-exchange. Adsorption and ion exchange are processes that employ certain materials, that can be collectively named ion scavengers, to remove ions from aqueous solutions. Some of the scavenger materials are still barely studied, in particular polyampholytes - polymeric zwitterionic materials. This review showcases papers published on toxic metal ion removal by polyampholytes, both commercial and experimental, over last two decades. Many recent publications show promising properties of experimental materials that match or even outperform commercial scavengers. This review was prepared to encourage other researchers to investigate this broad and still not well-studied class of materials especially in context of their ion-scavenging properties. Polyamphytes which may be especially worth the attention and further research have been highlighted as literature studies show that the most unexplored materials in the class of polyamphytes are those containing aminomethylphosphonate, aminomethylsulfonate or hypophosphorous acid group.

Thallium Use, Toxicity, and Detoxification Therapy: An Overview

Thallium (Tl) is released into the environment, where is present at very low levels, from both natural and anthropogenic sources. Tl is considered as one of the most toxic heavy metals; it is a non-essential metal, present in low concentrations in humans. Tl toxicity causes dermatological and gastrointestinal diseases and disorders of the nervous system, and may even result in death. Many isotopes of Tl exist, with different uses. One of the isotopes of this metal (201Tl) is used in cardiovascular scintigraphy and for the diagnosis of malignant tumors such as breast or lung cancer and osteosarcoma bone cancer. Many Tl compounds are tasteless, colorless, and odorless. Due to these characteristics and their high toxicity, they have been used as poisons in suicides and murders for criminal purposes, as well as instances of accidental poisoning. Impaired glutathione metabolism, oxidative stress, and disruption of potassium-regulated homeostasis may play a role in the mechanism of Tl toxicity. Solanum nigrum L. and Callitriche cophocarpa have been suggested as promising agents for the phytoremediation of Tl. In addition, macrocyclic compounds such as crown ethers (18-crown-6) are good candidates to absorb Tl from wastewater. Through this review, we present an update to general information about the uses and toxicity of Tl. Furthermore, the attention is focused on detoxification therapies.

Retention of thallium by natural minerals: A review

Though thallium (Tl) is usually present in trace amounts in natural environments, its biotoxicity is extremely high. With the development of mining, the metallurgy industry, and the growing application of Tl in high-tech fields, the threat of Tl to ecological environments and human health is increasing. Natural minerals, such as clay minerals, iron oxides, and manganese oxides, are natural Tl adsorbents due to their mineralogy and crystal structures. In this review, we discuss the mechanisms of Tl adsorption by various natural minerals, compare the adsorption capacities of common soil minerals for Tl, and describe the limitations of traditional sequential extraction methods for identifying the chemical states of Tl on minerals and source of Tl. We also provide suggestions on future directions needed in Tl research including a) additional in-depth studies on the competitive adsorption of Tl by minerals; b) more direct comparison of Tl adsorption behavior from lab-based experiments with field observations to clarify the mechanisms of Tl adsorption by minerals under environmental conditions; c) more research data are needed to support the establishment and improvement of relevant research methods based on modern leading-edge technologies such as synchrotron radiation. Further, we suggest further research is needed in adsorption technologies used for Tl treatment. This is the first review on the research progress of Tl adsorption by natural minerals with the purpose of helping understanding the mechanisms of Tl migration and transformation controlled by natural minerals, and providing theoretical supports for the development of Tl adsorbents and the treatments of Tl pollution.

Thallium in aquatic environments and the factors controlling Tl behavior

Although thallium (Tl) usually exists in a very low level in the natural environment, it is highly toxic. With the development of mining and metallurgical industry and the wide application of Tl in the field of high technologies, Tl poses an increasing threat to the ecological environment and human health. This paper summarizes the research results of the toxicity of Tl as well as the distribution, occurrence forms, migration, and transformation mechanism of Tl in rivers, lakes, mining areas, estuaries, coastal waters, and oceans. It also discusses the influence mechanisms of pH, redox potential, suspended particulate matters, photochemical reaction, natural minerals, cation/anion, organic matters, and microorganisms on the environmental behavior of Tl. This paper points out the shortcomings of Tl research methods in water environment, and looks forward to the future development directions: First, the technology for separating Tl(III) and Tl(I) is still immature, especially it is difficult to effectively separate Tl(III) and Tl(I) in seawater. Second, the development of many advanced in situ detection technologies will bring great convenience to the studies of the dynamic mechanisms of Tl migration and transformation in the environments. Third, adsorption is the most effective mechanism to remove Tl from water, in which modified metal oxides or macrocyclic organic compounds have high application potential.

Thallium(I) Salts: New Partners for Calix[4]pyrroles

Calix[4]pyrrole 1 can form host-guest complexes with certain thallium salts, for example, TlF, not only in the gas phase but also in solution and in the solid state. The complexation of TlF by calix[4]pyrrole 1 was found to promote self-assembly and the formation of well-defined and highly ordered fibrous supramolecular morphologies, as revealed by polarizing microscopy and scanning electron microscopy. The findings reported here serve to broaden the scope of cationic substrates that may be complexed as ion pairs by calix[4]pyrrole receptors while setting the stage for the development of new hosts for thallium(I) salts.

Efficacy of treated sodium alginate and activated carbon fibre for Pb(II) adsorption

Efficacy of treated sodium alginate (TSA) and activated carbon fibre (ACF) for aqueous Pb(II) uptake was comparatively investigated. By employing FTIR, SEM, EDX, XRD, point of zero charges and surface area measurements, the available functional groups, morphology, crystallinity, surface charge and surface areas of both adsorbents were respectively elucidated. The Pb(II) uptake performance of both adsorbents was also studied via batch mode at varied process conditions. The experimental isotherm and kinetic data for both adsorbents were best fitted to nonlinear forms of Langmuir and pseudo-first-order models, respectively. Similarly, intraparticle diffusion was the sole controlling mechanism. Despite the huge variation in the surface area, TSA (7.8 m²/g) with high carboxyl content (395.6 meq-COOH/100 g of sample) performed better by all standards than the ACF (975 m²/g). This finding showed that although the surface area of a given adsorbent is a key indicator of its adsorptive performance, the inherent surface functional groups play a superior role. The experimentally derived maximum adsorption capacities of 221.25 mg/g (for TSA) and 183.34 mg/g (for ACF) were recorded at an equilibrium time of 30 min and 45 min, respectively. Therefore, TSA and ACF demonstrated effectiveness for aqueous Pb (II) sequestration.

Prussian Blue: A Safe Pigment with Zeolitic-Like Activity

Prussian blue (PB) and PB analogues (PBA) are coordination network materials that present important similarities with zeolites concretely with their ability of adsorbing cations. Depending on the conditions of preparation, which is cheap and easy, PB can be classified into soluble PB and insoluble PB. The zeolitic-like properties are mainly inherent to insoluble form. This form presents some defects in its cubic lattice resulting in an open structure. The vacancies make PB capable of taking up and trapping ions or molecules into the lattice. Important adsorption characteristics of PB are a high specific area (370 m2 g-1 determined according the BET theory), uniform pore diameter, and large pore width. PB has numerous applications in many scientific and technological fields. PB are assembled into nanoparticles that, due to their biosafety and biocompatibility, can be used for biomedical applications. PB and PBA have been shown to be excellent sorbents of radioactive cesium and radioactive and nonradioactive thallium. Other cations adsorbed by PB are K+, Na+, NH4+, and some divalent cations. PB can also capture gaseous molecules, hydrocarbons, and even luminescent molecules such as 2-aminoanthracene. As the main adsorptive application of PB is the selective removal of cations from the environment, it is important to easily separate the sorbent of the purified solution. To facilitate this, PB is encapsulated into a polymer or coats a support, sometimes magnetic particles. Finally, is remarkable to point out that PB can be recycled and the adsorbed material can be recovered.

Microbial insights into the biogeochemical features of thallium occurrence: A case study from polluted river sediments

Thallium (Tl) is a trace element with extreme toxicity. Widespread Tl pollution in riverine systems, mainly due to escalating mining and smelting activities of Tl-bearing sulfide minerals, has attracted increasing attention. Insights into the function of the microbial communities with advanced characterization tools are critical for understanding the biogeochemical cycle of Tl. Herein, microbial communities and their adaptive evolution strategies in river sediments from a representative Tl-bearing pyrite mine area in southern China were profiled via 16S rRNA gene sequence analysis and shotgun metagenomic analysis. In total, 64 phyla and 778 genera of microorganisms were observed in the studied sediments. The results showed that pH, Tl, Pb, Zn and total organic carbon (TOC) had a significant influence on microbial community structure. Some important reductive microorganisms (such as Erysipelothrix, Geobacter, desulfatiferula, desulfatihabadium and fusibacter) were involved in the biogeochemical cycle of Tl. The ruv, rec, ars and other resistance genes enhanced the tolerance of microorganisms to Tl. The study suggested that relevant C, N and S cycle genes were the main metabolic paths of microorganisms surviving in the high Tl-polluted environment. The findings were critical for establishment, operation and regulation in the microbial treatment of Tl containing or related wastewater.

Selective Capture of Thallium and Cesium by a Cryptophane Soluble at Neutral pH

We report in this article the synthesis of an asymmetrical cryptophane derivative (possessing only C₃-symmetry) bearing three phenol groups and three other carboxylic acid functions, each of these groups on the aromatic rings. Thanks to isothermal titration calorimetry experiments, we show that this compound binds large monovalent cations, such as Cs⁺ and Tl⁺, with a binding constant significantly lower than its congeners bearing a larger number of phenol groups grafted on the benzene rings. However, higher selectivity for Cs⁺ and Tl⁺ was observed with this compound since it does not show any affinity for other alkali cations. More importantly, due to the greater solubility of this derivative in pure water, we show for the first time that effective thallium(I) complexation takes place at neutral pH. This result demonstrates that cryptophane derivatives decorated with a higher number of phenol groups are promising host molecules for removing traces of thallium(I) from aqueous phases at neutral pH or above.