Hydroxyapatite biomaterial production from chicken (femur and beak) and fishbone waste through a chemical less method for Cd2+ removal from shipbuilding wastewater

Surface coordination induced a quasi p-n junction for efficient visible light driven degradation of tetracycline over hydroxyapatite

The removal of antibiotics from aquatic solutions remains a global environmental challenge. In this work, the photocatalytic removal of a typical antibiotic-tetracycline (TC) using hydroxyapatite (HAp) as a catalyst was investigated. It was impressive that TC could be efficiently degraded by HAp under visible light irradiation, even though both HAp and TC exhibited poor harvesting in visible light region. The experimental and theoretical explorations were undertaken to thoroughly investigate the underlying mechanism of visible light degradation of TC over HAp. The results indicated that the formed TC-HAp complexes via surface coordination played an important role as photosensitizers for the visible light response. Together with the formation of a quasi p-n junction via band alignment, the photogenerated electrons in the highest unoccupied molecular orbital (HOMO) of TC-HAp were excited to the lowest unoccupied molecular orbital (LUMO) and subsequently migrated to the conduction band of HAp to achieve the efficient charge separation. Superoxide radicals and holes were found to be the major active species for TC degradation. The toxicity evaluation showed that TC could be transferred to the lower toxic intermediates, and deep oxidation with prolonged reaction time was necessary to eliminate the toxicity of TC. This work demonstrates the surface coordination with subsequent quasi p-n junction mechanism of TC degradation over HAp under visible light, which will stimulate us to explore new efficient photocatalytic systems for the degradation of various contaminants.

Penicillium oxalicum induced phosphate precipitation enhanced cadmium (Cd) immobilization by simultaneously accelerating Cd biosorption and biomineralization

Soil cadmium (Cd) is immobilized by the progressing biomineralization process as microbial induced phosphate precipitation (MIPP), which is regulated by phosphate (P) solubilizing microorganisms and P sources. However, little attention has been paid to the implications of Cd biosorption during MIPP. In this study, the newly isolated Penicillium oxalicum could immobilize 5.4-12.6 % of Cd2+, while the presence of hydroxyapatite (HAP) considerably enhanced Cd2+ immobilization in P. oxalicum and reached over 99 % Cd2+ immobilization efficiency within 7 days. Compared to P. oxalicum mono inoculation, MIPP dramatically boosted Cd biosorption and biomineralization efficiency by 71 % and 16 % after 96 h cultivation, respectively. P. oxalicum preferred to absorbing Cd2+ and reaching maximum Cd2+ biosorption efficiency of 87.8 % in the presence of HAP. More surface groups in P. oxalicum and HAP mineral involved adsorption which resulted in the formation of Cd-apatite [Ca8Cd2(PO4)6(OH)2] via ion exchange. Intracellular S2-, secreted organic acids and soluble P via HAP solubilization complexed with Cd2+, progressively mineralized into Cd5(PO4)3OH, Cd(H2PO4)2, C4H6CdO4 and CdS. These results suggested that Cd2+ immobilization was enhanced simultaneously by the accelerated biosorption and biomineralization during P. oxalicum induced P precipitation. Our findings revealed new mechanisms of Cd immobilization in MIPP process and offered clues for remediation practices at metal contaminated sites.

Synergistic adsorption of methylene blue with carrageenan/hydrochar-derived activated carbon hydrogel composites: Insights and optimization strategies

The study explores the use of hydrochar-derived activated carbon (AC) to improve the adsorption capacity and mechanical properties of carrageenan (CAR) hydrogel beads. Four distinct samples, with carrageenan to activated carbon ratios of 1:0 (CAR), 2:1 (CAC2), 4:1 (CAC4), and 10:1 (CAC10), were prepared. These polymeric beads underwent comprehensive evaluation for their methylene blue (MB) adsorption capacity, gel content (GC), and swelling ratio (SR). Increasing activated carbon content up to 50 % of carrageenan mass significantly enhanced GC and SR by 20.57 % and 429.24 %, respectively. Various analytical techniques were employed to characterize the composites, including FTIR, XRD, Raman Spectroscopy, BET, SEM, and EDS-Mapping. Batch adsorption tests investigated the effects of pH, contact time, dye concentration, and temperature on MB adsorption. Maximum adsorption capacities for CAR, CAC10, CAC4, and CAC2 were 475.48, 558.54, 635.93, and 552.35 mg/g, respectively, under optimal conditions. Kinetic models (Elovich and pseudo-second-order) and isotherm models (Temkin for CAR and Freundlich for CAC10, CAC4, and CAC2) fitted well with the experimental data. Thermodynamic analysis showed spontaneous, exothermic MB adsorption. Primary mechanisms include electrostatic attraction, hydrogen bonding, n-π, and π-π stacking. The study highlights enhanced adsorption capacity of carrageenan hydrogel via carrageenan/activated carbon composites, providing cost-effective wastewater treatment.

A biohybrid nanomaterial of biosynthesized TiO2 NPs from Mangrove leaf and shrimp shell-based Chitosan: ultrasonic-assisted synthesis and its application for methylene blue removal and COD reduction of real industrial wastewater

In the present study, TiO2 NPs (particle size: 25-35 nm) were biosynthesized from the Mangrove leaf extract. These nanoparticles were used to modify chitosan, and Chitosan@TiO2 biohybrid nanomaterial was synthesized and characterized using FTIR, XRD, BET, and, EDX-FE-SEM analyses. The adsorption ability of Chitosan@TiO2 nanomaterial has been investigated for Methylene blue (MB) removal from aqueous solution. The results indicated that the amount of MB removal is high in alkaline pH (optimum pH = 9). The pseudo-second-order model was able to describe the effect of contact time on the adsorption ability. The Langmuir model well described the equilibrium manner, and one gram of Chitosan@TiO2 could attract 416.66 mg of MB. Kinetic data, values of parameters of activation energy (+57.283 kJ/mol), enthalpy (-86.8148 kJ/mol), and Gibbs free energy (-27.999 to -22.8987 kJ/mol) indicate the dominance of chemical adsorption over physical adsorption. The breakthrough curves of 3 adsorption/desorption cycles showed the acceptable ability and reusability of prepared nanomaterial. Synthesized biohybrid nanomaterial can reduce 75% COD and 79% nitrate of the effluent from industrial city no.3 of Yasouj. The results of this research show the high ability of chitosan@TiO2 biohybrid to remove dyes from wastewater and reduce the pollution load of industrial wastewater.

Hydroxyapatite and its composite in heavy metal decontamination: Adsorption mechanisms, challenges, and future perspective

Nanohydroxyapatite (n-HAP), recognized by its peculiar crystal architecture and distinctive attributes showcased the underlying potential in adsorbing heavy metal ions (HMI). In this paper, the intrinsic mechanism of HMI adsorption by n-HAP was first revealed. Subsequently, the selectivity and competitiveness of n-HAP for HMI in a variety of environments containing various interferences from cations, anions, and organic molecules are elucidated. Next, n-HAP was further categorized according to its morphological dimensions, and its adsorption properties and intrinsic mechanisms were investigated based on these different morphologies. It was shown that although n-HAP has excellent adsorption capacity and cost-effectiveness, its application is often challenging to realize due to its inherent fragility and agglomeration, the technical problems required for its handling, and the difficulty of recycling. Finally, to address these issues, this paper discusses the tendency of n-HAP and its hybridized/modified materials to adsorb HMI as well as the limitations of their applications. By summarizing the limitations and future directions of hybridization/modification HAP in the field of HMI contamination abatement, this paper provides insightful perspectives for its gradual improvement and rational application.

Fabrication of magnetic nanocomposite scaffolds based on polyvinyl alcohol-chitosan containing hydroxyapatite and clay modified with graphene oxide: Evaluation of their properties for bone tissue engineering applications

One of the most common systems for bone tissue engineering is polymeric scaffolds. However, the low mechanical properties of polymeric scaffolds, considering the properties required for bone replacement tissue, are the main challenge for researchers in this field. For bone tissue engineering, this research prepared nanocomposite scaffolds based on polyvinyl alcohol-chitosan containing modified clay and hydroxyapatite (HAp). HAp used in these 3D scaffolds was synthesized from a chicken femur, and Cloisite 30B clay nanoparticles were modified by graphene oxide and Fe3O4 nanoparticles to strengthen their mechanical properties. Sample characteristics were determined using FT-IR, XRD, SEM, TGA, swelling rate, laboratory degradation, and biological and mechanical properties. These analyses showed that 2% of modified clay (C30B/GO/Fe3O4, CGF) inside the nanocomposite scaffold increased the compressive strength 23 times compared to the pristine polymer scaffold. Also, adding HAp particles and modified clay simultaneously increased the mineralization on the surface of the scaffolds. Final nanocomposite scaffolds were found to have a compressive strength of 9.31 MPa, a porosity of 75 %, and a porosity size of 50 nm and were in the range of cancellous bone. The final swelling amount is 1790 %, which is the amount that is Favorable for bone scaffold. Finally, the analysis results to determine the samples' toxicity showed that none of the prepared scaffolds were toxic and showed good cell viability.

Machine learning approaches for the treatment of textile wastewater using sugarcane bagasse (Saccharum officinarum) biochar

Most dyes present in wastewater from the textile industry exhibit toxicity and are resistant to biodegradation. Hence, the imperative arises for the environmentally significant elimination of textile dye by utilising agricultural waste. The achievement of this objective can be facilitated through the utilisation of the adsorption mechanism, which entails the passive absorption of pollutants using biochar. In this study, we compare the efficacy of the response surface methodology (RSM), the artificial neural network (ANN), the k-nearest neighbour (kNN), and adaptive neuro-fuzzy inference system (ANFIS) in removing crystal violet (CV) from wastewater. The characterisation of biochar is carried out by scanning electron microscope (SEM) and Fourier transform infrared (FTIR). The impacts of the solution pH, adsorbent dosage, initial dye concentration, and temperature were investigated using a variety of models (RSM, ANN, kNN, and ANFIS). The statistical analysis of errors was conducted, resulting in a maximum removal effectiveness of 97.46% under optimised settings. These conditions included an adsorbent dose of 0.4 mg, a pH of 5, a CV concentration of 40.1 mg/L, and a temperature of 20 °C. The ANN, RSM, kNN, and ANFIS models all achieved R2 0.9685, 0.9618, 0.9421, and 0.8823, respectively. Even though all models showed accuracy in predicting the removal of CV dye, it was observed that the ANN model exhibited greater accuracy compared to the other models.

Fabrication of highly efficient hydroxyapatite microtubes for uranium sequestration and immobilization

Uranium-containing wastewater is a common by-product of uranium mining. Phosphate and phosphate minerals can interact with uranyl ions [U(VI)], impeding the migration of these ions by forming relatively stable uranium-containing crystalline phase(s). In this study, hydroxyapatite microtubes (HAP-T) were fabricated to sequester uranyl ions from simulated radioactive wastewater. HAP-T had excellent adsorption and stability properties; over 98.76% of U(VI) could be sequestrated by 0.25 g/L HAP-T within 5 min at pH = 4.0. The isotherms and kinetics data could be suitably reflected by the Freundlich and the pseudo second-order kinetic models, respectively. The maximum adsorption capacity of HAP-T was 356.42 mg/g. The adsorption ability of HAP-T for U(VI) was inhibited when Mg2+ or SO42- ions or fulvic acid (FA) substances existed in the simulated radioactive wastewater. The inhibition by FA was attributed to its negative charges, which caused competition between FA and HAP-T for uranium sequestration. The primary mechanisms of U(VI) sequestration by HAP-T were electrostatic interactions and surface complexation. The effectiveness of HAP-T, HAP-B (bio-hydroxyapatite synthesized from fish bone), and HAP-C (commercially available synthesized hydroxyapatite) for uranium immobilization was compared; HAP-T was more effective than HAP-B or HAP-C in immobilizing uranium. HAP-T, which has a micron-sized tubular structure, is likely less mobile in groundwater than are HAP-B and HAP-C, which have nanoscale granular structures. In conclusion, HAP-T can be used to sequester and immobilize uranyl ions.

Adsorption of Methyl Red and Methylene Blue on Carbon Bioadsorbents Obtained from Biogas Plant Waste Materials

In this study, biocarbon was obtained from the waste material corn digest. Carbon adsorbents were obtained by physical activation of the precursor with CO2. Detailed physicochemical characterization of the biocarbon was carried out using low-temperature nitrogen adsorption/desorption, Boehm titration, zero-charge point (pHpzc) and iodine number. In addition, the sorption capacity of the biocarbon agents towards an aqueous solution of methylene blue and methyl red was determined, and the kinetics of the adsorption process were determined. The biocarbon adsorbents were characterized by an average developed specific surface area covering the range from 320 to 616 m2/g. The sorption capacity of the biocarbon adsorbents against methylene blue ranged from 40 mg/g to 146 mg/g, and for methyl red it covered the range from 31 mg/g to 113 mg/g. It was shown that the efficiency of organic dye removal by the obtained biocarbons depends on the initial concentration of the adsorbate solution, its mass, shaking rate, adsorbent-adsorbate contact time and temperature. The results obtained from the Langmuir and Freundlich kinetic models showed that the Langmuir model is the most suitable model for describing the adsorption of the studied pollutants on biocarbon. In turn, the adsorption kinetics of dyes is described according to the pseudo-second-order model. Adsorption studies also showed that as the process temperature increases, the removal efficiency of methylene blue and methyl red increases.

Mussel inspired synthesis of polydopamine/polyethyleneimine-grafted fly ash composite adsorbent for the effective separation of U(VI)

Polydopamine/polyethyleneimine-grafted fly ash composite (PDA/PEI/FA), an efficient multifunctional adsorbent for U(VI) with excellent separation efficiency (94.5 %) and capacity (422.5 mg/g), was synthesized by grafting PDA and PEI on FA via Mussel inspiration and Michael addition reaction. The introduction of PDA and PEI had brought numerous functional groups with fine affinities to uranium, like catechol, amino and imino, causing good U(VI) separation performances. Langmuir and Pseudo-second-order models were well matched with experimental data, illustrating the U(VI) separation on PDA/PEI/FA was a homogeneous chemical adsorption process. After five cycles, the U(VI) adsorption efficiency for PDA/PEI/FA was still up to 90.2 %, implying that PDA/PEI/FA possessed good stability and reusability. Besides, the good dynamic adsorption performances of PDA/PEI/FA further demonstrated that PDA/PEI/FA was an ideal adsorbent for the practical wastewater treatment. According to the characterization results, U(VI) was absorbed by PAD/PEI/FA through complexation, redox reaction, electrostatic attraction and hydrogen bonding. Given the above, PDA/PEI/FA showed good practical application prospect in U(VI) separation.

Recycling of phosphate tailings for an efficient hydroxyapatite-based adsorbent to immobilize heavy metal cations

Hydroxyapatite (HAP) is a promising adsorbent for immobilizing heavy metals in soil and water. However, the preparation and modification of HAP from pure chemicals increases its cost and limits its large-scale practical application. In this study, a hydroxyapatite-based adsorbent (HAP_PT) was prepared from phosphate tailing produced in the phosphorus industry to sequester Pb, Cd and Zn from solution. The results showed that HAP_PT was composed of HAP and MgO, with a surface area of 27.74 m²/g. The kinetics studies showed that most Pb and Cd were removed from the initial solution in 4 h and the adsorption of Zn increased with increasing contact time. Metals presented higher adsorption capacities at 35 °C than that at 25 °C. The adsorption isotherms showed that HAP_PT presented high adsorption capacities for Pb, Cd and Zn in mono-metal solutions. The adsorption capacity of Cd at pH 6 was higher than that at pH 3, but the adsorption for Pb and Zn was similar at both pHs. HAP_PT has selectivity for Pb in Pb-Cd-Zn multi-metals solution, and competitive adsorption reduced the adsorption quantity by 53%, 93% and 79% for Pb, Cd and Zn, respectively. The combined results of TEM-EDS, XRD and XPS showed that Pb was immobilized by forming phosphates due to the dissolution of HAP, whereas Cd and Zn were immobilized by forming hydroxide precipitates resulting from the function of MgO in HAP_PT. The results of this study provided an efficient adsorbent for the removal of heavy metals in solution and provided a new perspective on the recycling of phosphate tailings in the phosphorus industry.

Green synthesized hydroxyapatite for efficient immobilization of cadmium in weakly alkaline environment

The development of cost-effective passivators for the remediation of heavy metal-contaminated soils has been a research hotspot and an unsolved challenge. Herein, a novel hydroxyapatite (GSCH) was synthesized by co-precipitating distiller effluent-derived Ca with (NH₄)₂HPO₄ using straw-derived dissolved organic matter (S-DOM) as the dispersant. Batch adsorption experiments and soil incubation tests were performed to assess the immobilization efficiency of GSCH for Cd in weakly alkaline environments. As a result, GSCH showed an excellent adsorption efficiency to Cd with a maximum adsorption amount of ∼222 mg g^-1, which was fairly competitive compared to other similar previously materials reported. The kinetic data indicated that the adsorption of Cd on GSCH was a chemical and irreversible process, while the thermodynamic data revealed a spontaneous (ΔG° < 0) and endothermic (ΔH° > 0) adsorption process. Based on mechanism analysis, both physisorption (e.g., electrostatic attraction and pore filling) and chemisorption (e.g., ion exchange and complexation) were responsible for Cd adsorption on GSCH. Particularly, the incorporated S-DOM and hydroxyapatite phase in GSCH acted synergistically in the adsorption process. The incubation results showed that GSCH application could significantly reduce the bioavailability, phytoavailability and bioaccessibility of Cd in soil by 48.4%-57.8%, 20.4%-28.6% and 12.6%-24.0%, respectively. Moreover, GSCH application also improved soil bacterial communities and enhanced soil nutrient availability. Overall, this is the first study to demonstrate the potential application value of GSCH in Cd immobilization, providing promising insights into the development of green and cost-effective hydroxyapatite-based passivators for the remediation of heavy metal-contaminated soils.

The deconstruction and recombination of endogenous active units of carbon@chitosan@montmorillonite nanosheet microsphere adsorbent caused by cadmium and copper cations benefit for high adsorption performance

The highly efficient removal of heavy metals is one of the important factors to evaluate adsorbents. In our study, carbon@chitosan@montmorillonite nanosheet (C@CS@MTN) was successfully prepared via layer-by-layer assembly for the removal of Cu2+ and Cd2+ from solution. High-intensity ultrasound peeling technology was used to release Si-O tetrahedron and Al-O octahedron from montmorillonite in order to exert their optimal adsorption potential. Fourier transform infrared spectroscopy, an X-ray diffractometer, BET surface area measurement, and the inductively coupled plasma emission spectrometry were adopted to investigate the morphology, functional groups, and adsorption capacity of C@CS@MTN. Batch experiment results indicated that both Cu2+ and Cd2+ were effectively removed from solution with the range of pH from 2 to 6. The removal ratio of Cu2+ and Cd2+ onto C@CS@MTN increased with the rise of reaction temperature and their maximum adsorption capacities reached 1108.8 mg·g-1 and 237.4 mg·g-1, respectively, under the condition of the reaction temperature 40 °C, the reaction time 4 h, and the pH = 6. The molecular simulation calculation indicated that there was an obvious electron transfer between Si-O tetrahedron and metal cations, but not for Al-O octahedron. In comparison to Al-O octahedron, the bonding of Cu-O and Cd-O caused the Si-O bond to be broken, resulting in the deconstruction of Si-O tetrahedron and their recombination via the junction of O atoms. It was exactly the deconstruction and recombination of endogenous active units that provide more sites for metal ion adsorption.

Optimization of Cd (II) removal from aqueous solution by natural hydroxyapatite/bentonite composite using response surface methodology

Toxic cadmium (Cd) was removed from water using eggshell-based hydroxyapatite (HAp) grafted bentonite (HAp/bentonite) composite through a straightforward chemical synthesis route. The as-prepared adsorbents were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and Brunauer–Emmett–Teller analysis (BET). Optimization of the initial adsorbate concentration, adsorbent dosage, pH, and contact time—all of which affect the adsorption process—was performed using the central composite design (CCD) of the response surface methodology (RSM). 99.3 percent adsorptive removal efficiency was observed at an initial concentration of 61.58 mg/L of Cd (II), with an adsorbent dosage of 1.58 g, a solution pH of 5.88, and a contact time of 49.63 min. The analysis of variance (ANOVA) was performed, and the multiple correlation coefficient (R2) was found to be 0.9915 which confirms the significance of the predicted model. The Langmuir isotherm model best represented the adsorption isotherm data, which also predicted a maximum sorption capacity of 125.47 mg/g. The kinetic data were best described by the pseudo-second order model.

Adsorptive removal of Pb(II) using nanostructured γ-alumina in a packed bed adsorber: Simulation using gPROMS

In this work, convective-dispersive and pore volume and surface diffusion models have been used to analyze Pb(II) adsorption from an aqueous solution over a nanostructured γ-alumina adsorbent in a packed bed adsorber. The models encompassing partial differential equation and a linear algebraic equation coupled with isotherm have been simulated in gPROMS using the backward finite difference approach. The predicted breakthrough curves of Pb(II) adsorption concerning flow rate, initial metal concentration, and bed height were matched with the experimental data. The accuracy of model predictions was analyzed through statistical measures such as coefficient of determination (R²), root mean square error, and chi-squared value. The simulation results also predicted the axial dispersion, distribution coefficient, mass transfer coefficient, pore volume, and surface diffusion coefficient, which are, otherwise, difficult to measure experimentally and, in turn, have been used to assess the mass transfer characteristics of continuous Pb(II) adsorption. Additionally, the values of breakthrough time, exhaustion time, adsorption column capacity, and mass transfer zone were determined as a function of flow rate, bed height, and initial metal concentration. Surface and pore volume diffusions (10^-11-10^-10 m²/s) apparently controlled the continuous adsorption process, with surface diffusion being dominant. The transport parameters evaluated in the current study could be beneficial for the large-scale Pb(II)/nanostructured γ-alumina adsorption system. As evident from the successful simulation, the developed gPROMS program can also be applied to other adsorbate/adsorbent systems with a slight modification concerning the operating parameters.

Multicomponent adsorption of heavy metals onto biogenic hydroxyapatite: Surface functional groups and inorganic mineral facilitating stable adsorption of Pb(Ⅱ)

Due to the coexistence of various heavy metals in the contaminated environment, it is essential to comprehensively study the multicomponent adsorption of heavy metals in order to tackle these combined pollutants. Herein, the adsorption processes of Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by biogenic hydroxyapatite (BHAp) were investigated in single and multicomponent systems. The maximum adsorption capacity for Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by BHAp in single system reached 311.16, 82.05 and 92.54 mg g^-1, respectively, while adsorption capacity for Cu(Ⅱ) and Cd(Ⅱ) in multicomponent system decreased more obviously than that of Pb(Ⅱ). Furthermore, the stability of Cu(Ⅱ) and Cd(Ⅱ) adsorbed on BHAp was indeed influenced in multicomponent system. By means of the characterization analysis, it was found that ion exchange was more instrumental in the adsorption processes of Cu(Ⅱ) and Cd(Ⅱ) in single system than in multicomponent system. Significantly, it was observed that the proportion of generally stable Pb(II) adsorbed on BHAp exceeded 95% in both single and multicomponent systems. This result might be due to the in-site growth of stable crystals of Pb_xCa_10-x(PO₄)₆(OH)₂, which was synergistically induced by surface functional groups and inorganic mineral of BHAp, and was unaffected by the coexistence of Cu(Ⅱ) and Cd(Ⅱ).

Adsorptive removal of Cd2+ ions using dolochar at an industrial-scale process optimization by response surface methodology

In this work, performance of laboratory-synthesized dolochar has been investigated for adsorption of Cd²⁺ ions in a large-scale process with the application of Aspen Adsorption. Moreover, the optimum values of the operating parameters (namely, flow rate, bed height, and inlet metal ion concentration) that would result into maximum amount of cadmium ion adsorption (high exhaustion capacity) in minimum time (less exhaustion time) for a fixed mass of dolochar have been calculated via the application of response surface methodology. It was found that, at optimum values of bed height (3.48 m), flow rate (76.31 m³/day), and inlet concentration (10 ppm), the optimized value of exhaustion capacity and exhaustion time for cadmium ion adsorption in dolochar packed bed is equal to 1.85 mg/g and 11.39 h, respectively. The validity of these simulation experiments can be proven by the fact that the obtained exhaustion capacity of dolochar packed bed always remained in close proximity of the experimentally obtained value of adsorption capacity of the dolochar in batch process mode (equal to 2.1 mg/g).

In situ synthesis of magnesium-doped hydroxyapatite aerogel for highly efficient U(VI) separation with ultra high adsorption capacity and excellent recyclability

Mg-doped HAP aerogel (MHAPA) was firstly in situ prepared via freeze-drying-calcination technology to capture U(VI). The U(VI) removal capacity by MHAPA even arrived 2685.6 mg g^-1, which was about 2 times over purchased HAP, illustrating that the incorporation of Mg ions could greatly enhance the U(VI) removal capacity. Compared with HAP, MHAPA also showed better anti-ion interference ability and dynamic removal performances. In comparison with other HAP-based adsorbents, MHAPA possessed good recyclability and its desorption rate was up to 93.4% in the first cycle. The excellent U(VI) removal performances of MHAPA might be owing to its low crystallinity and grain size, fast ion exchange rate and partial ionization under acidic conditions, which would accelerate the process of electrostatic attraction, ion-exchange, and complexation to immobilize U(VI). To sum up, the prepared MHAPA was expected to be an environmentally friendly, recyclable and effective adsorbent to immobilize U(VI) in actual wastewater.

Graphene oxide supported sulfidated nano zero-valent iron (S-nZVI@GO) for antimony removal: The role of active oxygen species and reaction mechanism

Sulfidated nano zero-valent iron (S-nZVI) was used to remove various pollutants from wastewater. However, the instability, poor dispersibility, and low electron transfer efficiency of S-nZVI limit its application. Herein, graphene oxide supported sulfidated nano zero-valent iron (S-nZVI@GO) was successfully synthesized using graphene oxide (GO) as a carrier. The properties of S-nZVI@GO were characterized by scanning electron microscopy coupled to X-ray photoelectron spectroscopy (SEM-EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) concerning the surface morphology, crystalline structure, and elemental components. S-nZVI@GO displayed an excellent capacity for antimony (Sb) removal under aerobic conditions (96.7%), with a high adsorption capacity (Q_max = 311.75 mg/g). It maintained a high removal rate (over 90%) during a wide pH range (3-9). More importantly, S-nZVI@GO activated the molecular oxygen in water via a single-electron pathway to produce •O₂－ and H₂O₂, and then oxidized trivalent antimony (Sb(III)) to pentavalent antimony (Sb(V)) and further separated it by synergistic adsorption and co-precipitation. Therefore, S-nZVI@GO shows excellent potential for Sb contamination remediation.

Photocatalytic activity of calcined chicken eggshells for Safranin and Reactive Red 180 decolorization

One of the most important problems affecting the environment today is the inability to adequately treat wastewater containing dyes. Among of the many treatment processes used in the treatment of dye-containing wastewater, photocatalytic based wastewater treatment processes attract the attention of scientists as a new, economically feasible, and promising approach which has been in practice for a few decades. However, in order to use these processes in wider areas, cheap and effective catalysts are still being developed today. In this study, the photocatalytic activity of eggshell-CaO produced from waste chicken eggshells was investigated for decolorization of Safranin (Basic Red 2) and Reactive Red 180 (RR180) dyes. First, sintering process was applied to the waste chicken eggshells at different temperatures (300, 600, 900 °C) in order to observe CaO formation from the eggshells. Second, the parameters such as photocatalyst amount, pH, concentration of dyes, and reaction time were optimized on dye removal efficiency in photocatalytic experiments. The optimum conditions were performed under visible light and found to be 1 g/L of catalyst amount (sintered at 900 °C), original solution pH (6.80 for Safranin and 6.60 for RR180), and 5 mg/L of dye concentration. The photocatalytic removal efficiencies of Safranin and RR180 dyes were 100% and 97.90%, respectively, under the determined optimum experimental conditions. The adsorption efficiency of the dyes that could be realized during the photocatalytic experiment was measured as 20.99% and 9.99% for Safranin and RR180 dyes, respectively.

Surface magnetization of hydrolyzed Luffa Cylindrica biowaste with cobalt ferrite nanoparticles for facile Ni2+ removal from wastewater

A novel magnetic adsorbent based on hydrolyzed Luffa Cylindrica (HLC) was synthesized through the chemical co-precipitation technique, and its potential was evaluated in the adsorptive elimination of divalent nickel ions from water medium. Morphological assessment and properties of the adsorbent were performed using FTIR, SEM, EDX, XRD, BET, and TEM techniques. The effect of pH, temperature, time and nickel concentration on the removal efficiency was studied, and pH = 6, room temperature (25 °C), contact time of 60 min, and Ni²⁺ ion concentration of 10 mg.L^-1 were introduced as the optimal values. At optimal conditions, the removal efficiency of Ni²⁺ ions using HLC and HLC/CoFe₂O₄ magnetic composite was calculated as 96.38 and 99.13%, respectively. The adsorption process kinetic followed a pseudo-first-order model. Langmuir isotherm was suitable for modelling the experimental data of the Ni²⁺ adsorption. The maximum elimination capacity of HLC and HLC/CoFe₂O₄ samples was calculated as 42.75 and 44.42 mg g^-1, respectively. Furthermore, thermodynamic investigations proved the spontaneous and exothermic nature of the process. The adsorption efficiency was decreased with increasing the content of Ca²⁺ and Na ⁺ cations in aqueous media. During reusability of the synthesized adsorbents, it was found that after 8 cycles, no significant decrease has occurred in the adsorption efficiency. In addition, real wastewater treatment results proved that HLC/CoFe₂O₄ magnetic composite has an excellent performance in removal of heavy metals pollutant from shipbuilding effluent.

Review on biopolymers and composites - Evolving material as adsorbents in removal of environmental pollutants

The presence of pollutants and toxic contaminants in water sources makes it unfit to run through. Though various conventional techniques are on deck, development of new technologies are vital for wastewater treatment and recycling. Polymers have been intensively utilized recently in many industries owing to their unique characteristics. Biopolymers resembles natural alternative to synthetic polymers that can be prepared by linking the monomeric units covalently. Despite the obvious advantages of biopolymers, few reviews have been conducted. This review focuses on biopolymers and composites as suitable adsorbent material for removing pollutants present in environment. The classification of biopolymers and their composites based on the sources, methods of preparation and their potential applications are discussed in detail. Biopolymers have the potentiality of substituting conventional adsorbents due to its unique characteristics. Biopolymer based membranes and effective methods of utilization of biopolymers as suitable adsorbent materials are also briefly elaborated. The mechanism of biopolymers and their membrane-based adsorption has been briefly reviewed. In addition, the methods of regeneration and reuse of used biopolymer based adsorbents are highlighted. The comprehensive content on fate of biopolymer after adsorption is given in brief. Finally, this review concludes the future investigations in recent trends in application of biopolymer in various fields in view of eco-friendly and economic perspectives.

Green synthesized hydroxyapatite nanoadsorbent for the adsorptive removal of AB113 dye for environmental applications

The present work reports the synthesis of hydroxyapatite (HAp) via the green chemistry approach by using the leaf extract of copper pod tree and its adsorptive potential to remove Acid blue 113 (AB113) dye. FESEM-EDS characterization of the synthesized HAp confirmed rod-shaped HAp with prominent Ca and P elements. The crystallinity of HAp was ascertained by XRD and thermal stability was analyzed by TGA. The colloidal suspension stability was determined as - 17.7 mV by Zeta potential analyzer. The mesoporous structure was affirmed via BET studies with a high magnitude of specific surface area. TEM studies substantiated the rod-shaped HAp as observed in FESEM. The signals specific to HAp were observed in XPS studies. Adsorption of AB113 on the synthesized HAp was examined by varying the process parameters. Batch experiments resulted in an optimum dye removal of 92.72% at a pH of 8, 1 g/L of CP-HAp nps dosage, 20 ppm AB113 concentration, 120 min contact time, 150 rpm agitation speed and at room temperature. The maximum adsorption capacity reached 120.48 mg/g. Multifarious isotherms characterized the adsorption with Freundlich isotherm (R² > 0.968) dominating Langmuir indicating multilayer adsorption. The experimental data reasonably matched pseudo-second-order kinetics with R² exceeding 0.99. Thermodynamic investigations underlined the spontaneity and exothermicity of the processes. Results showed the suitability of the HAp nanoadsorbent to remove AB113 from wastestreams.

Adsorption of Organic Compounds on Adsorbents Obtained with the Use of Microwave Heating

Activated carbons were obtained by physical and chemical activation of the residue of supercritical extraction of green tea leaves. All the adsorbents obtained were characterized by: elemental analysis, low-temperature nitrogen adsorption, and the contents of acidic and basic oxygen functional groups on the surface of activated carbons by the Boehm method. The activated carbons were micro- or micro-mesoporous with well-developed surface area ranging from 520 to 1085 m²/g and total pore volume from 0.62 to 0.64 cm³/g. The physical activation of the precursor led to the strongly basic character of the surface. Chemical activation with 50% solution of H₃PO₄ of the residue of supercritical extraction of green tea leaves promoted the generation of acidic functional groups. All adsorbents were used for methylene blue and methyl red adsorption from the liquid phase. The influence of the activation method, pH of the dye solution, contact time of adsorbent with adsorbate, the temperature of adsorption, and rate of sample agitation on the effectiveness of organic dyes removal was evaluated and optimized. In the process of methylene blue adsorption on adsorbents, an increase in the sorption capacity was observed with increasing pH of the adsorbate, while in the process of methyl red adsorption, the relation was quite the reverse. The adsorption data were analyzed assuming the Langmuir or Freundlich isotherm models. The Langmuir model better described the experimental results, and the maximum sorption capacity calculated for this model varied from 144.93 to 250.00 mg/g. The results of the kinetic analysis showed that the adsorption of organic dyes on activated carbon was following the pseudo-second-order model. The negative values of the Gibbs free energy indicate the spontaneous character of the process.

Fabrication of alginate@silver nanoparticles (Alg@AgNPs) bionanocomposite for the sequestration of crystal violet dye from aqueous solution

In the present study, alginate@silver nanoparticles (Alg@AgNPs) bionanocomposite has been fabricated successfully and further explored for the removal of crystal violet (CV) dye from the aqueous solution. The surface morphology of the (Alg@AgNPs) bionanocomposite was characterized by various modern analytical techniques such as SEM-EDX, TEM, FTIR and XRD. The maximum adsorption was observed at optimum condition of (pH 7, adsorbent dose 0.01 g, equilibrium time 240 min and initial concentration 20 mg L^-1). The maximum monolayer adsorption capacity was found to be 186.93 mg g^-1 at 30 °C. The experimental data were further validated by various isotherm models and on the basis of highest correlation coefficient (R², 0.99), Langmuir model was found to be best fitted model. Pseudo-second order kinetic model obeyed best for the experimental data with a highest correlation coefficient (R², 0.99) at all studied temperature. In thermodynamic studies, the positive value of enthalpy change (∆H⁰) and entropy change (∆S⁰) confirmed the process to be endothermic and spontaneous in nature. Desorption studies shows that 83 % of the adsorbed CV can be desorbed in first cycle and can be regenerated up to 4th cycle effectively with 0.1 M HCl. Therefore, (Alg@AgNPs) bionanocomposite could be harnessed as a potential adsorbent for the removal of hazardous CV dye from the waste water.

Development of new magnetic adsorbent of walnut shell ash/starch/Fe3O4 for effective copper ions removal: Treatment of groundwater samples

The goal of this investigation was to develop a new magnetic nanocomposite of walnut shell ash (WSA)/starch/Fe₃O₄ to remove Cu (II) present in groundwater samples. The desired nanocomposites were successfully synthesized by the chemical deposition method. The specific active surface area for pristine WSA and WSA/starch/Fe₃O₄ magnetic nanocomposites was determined to be 8.1 and 52.6 m²/g, respectively. A central composite design for the response surface method was utilized to study the influence of pH, adsorbent quantity, initial content of Cu (II), temperature, and contact time. This method showed the success of the model to design process variables and to estimate the appropriate response. The P- and F-value determined for the quadratic polynomial model showed the significance and accuracy of the proposed model in examining experimental and predicted data with R² and Adj.R² of 0.994 and 0.991, respectively. The Cu adsorption onto WSA and WSA/starch/Fe₃O₄ obeyed the Freundlich and Langmuir models, respectively. The highest Cu (II) sorption capacity of 29.0 and 45.4 mg/g was attained for WSA and WSA/starch/Fe₃O₄, respectively. The free energy of Gibbs had a negative value at 25-45 °C indicating that the adsorption process is spontaneous. Also, negative ΔH values for copper adsorption showed that the processes are exothermic. The kinetic adsorption data for WSA and WSA/starch/Fe₃O₄ followed the pseudo-second order (PSO) model. The ability of the composite adsorbent to remove copper from three groundwater samples showed that it could be reused at least 3 times with appropriate efficiency, depending on the water quality.

Post-substitution of magnesium at CaI of nano-hydroxyapatite surface for highly efficient and selective removal of radioactive 90Sr from groundwater

We have modified the ion-exchange affinity of nano-Hydroxyapatite (Ca₅(PO₄)₃OH, HAP) surface for the rapid and selective adsorption of ⁹⁰Sr from groundwater. The modification was achieved by the post-substitution of cations (Na⁺, Mg²⁺, Cu²⁺, Ba²⁺, Fe³⁺, and Al³⁺) for parent Ca²⁺ within surface structure of HAP. The diffraction patterns of modified HAP showed a slight shift of the (002) peak between 25° and 27° 2θ depending the ionic radius of the substituted cation. Magnesium substituted HAP, Mg-HAP, exhibited the highest removal efficiency (>95%) for 10 ppm of Sr²⁺, which is attributable to the higher ion-exchange affinity of substituted Mg²⁺ than parent Ca²⁺ toward Sr²⁺. The results of various analyses revealed that Mg substitution dominantly occurred at the Ca^I site of HAP, which enabled the Mg-HAP to adsorb Sr²⁺ at both of Ca^I and Ca^II sites whereas bare HAP could adsorb Sr²⁺ mainly at Ca^II site. Adsorption isotherms and the kinetics of Mg-HAP for Sr²⁺ were evaluated using a bi-Langmuir isotherm and a pseudo-second-order kinetic model, which demonstrated the Mg-HAP exhibited the highest adsorption capacity (64.69 mg/g) and fastest adsorption kinetics (0.161-1.714 g/(mg·min)) than previously modified HAPs. In the presence of competing cations at circumneutral pHs, the enhanced performance of the Mg-HAP led to a greater than 97% reduction of ⁹⁰Sr (initial radioactivity = 9500 Bq/L) within 1 h. The distribution coefficient of Mg-HAP was 1.3-6.6 × 10³ mL/g while that of bare HAP was 1.2-6.6 × 10² mL/g. The findings in the present study highlight that the ion-exchange affinity of Ca^I and Ca^II sites on HAP surface plays a key-role in ⁹⁰Sr uptake. The proposed modification method can simply increase the affinity of HAP surface, therefore, this work can further improve the deployment of an in situ remediation technology for ⁹⁰Sr contaminated groundwater, i.e., Mg-HAP-based permeable reactive barrier.

Pyrene-based sulfonated organic porous materials for rapid adsorption of cationic dyes in water

Porous organic polymers (POP) have gained attention because of their high specific surface area, porosity and their simplicity in synthesis, but for the most part, they are hydrophobic because of their organic backbone, making it difficult to expand their applications. Here, we have obtained poly(pyrene) porous organic polymers (PyPOP) through the polymerization of pyrene monomers catalysed by aluminium trichloride, which is a simple and inexpensive synthesis method. The sulfonated poly(pyrene) porous organic polymers (PyPOP-SO₃H) obtained showed rapid adsorption of cationic dyes, especially malachite green (MG adsorption 1607 mg/g) and methylene blue (MB adsorption 1220 mg/g) in pH = 7 aqueous solution, room temperature. The results show that the Freundlich model is more in line with the adsorption process than the Langmuir model, whether for methylene blue or malachite green. In addition, the PSO kinetic model fits better than PFO kinetic model, whether it is for the adsorption of methylene blue or malachite green. The excellent adsorption performance of PyPOP-SO3H for cationic dyes may be due to the introduction of sulfonic acid groups, which not only increases the specific surface area but also allows better dispersion in water, increasing contact points and adsorption efficiency. This research expands the scope of exploration and application of POP.

Selenium removal from water using adsorbents: A critical review

Selenium (Se) has become an increasingly serious water contamination concern worldwide. It is an essential micronutrient for humans and animals, however, can be extremely toxic if taken in excess. Sorption can be an effective treatment for Se removal from a wide range of water matrices. However, despite the synthesis and application of numerous adsorbents for remediation of aqueous Se, there has been no comprehensive review of the sorption capacities of various natural and synthesized sorbents. Herein, literature from 2010 to 2021 considering Se remediation using 112 adsorbents has been critically reviewed and presented in several comprehensive tables including: clay minerals and waste materials (presented in Table 1); zero-valent iron, iron oxides, and binary iron-based adsorbents (Table 2); other metals-based adsorbents (Table 3); carbon-based adsorbents (Table 4); and other adsorbents (Table 5). Each of these tables, and their relevant sections, summarizes preparation/modification methods, sorption capacities of various Se adsorbents, and proposed model/mechanisms of adsorption. Furthermore, future perspectives have been provided to assist in filling noted research gaps for the development of efficient Se adsorbents for real-world applications. This review will help in preliminary screening of various sorbent media to set up Se treatment technologies for a variety of end-users worldwide.

Deep insight on mechanism and contribution of As(V) removal by thermal modification waste concrete powder

Expanding the utilization strategy of waste concrete powder (WCP) is conducive to minimizing the environmental burden caused by construction & demolition wastes (C&DW). In this study, WCP prepared in the laboratory was thermally treated and used to remove As(V) from wastewater. Batch adsorption tests were implemented to explore the influence factors such as modification temperature (0-850 °C), pH (1.00-12.00), dosage (2-50 g/L), co-coexisting ions (SO₄^2-, NO₃^-, Cl^- and PO₄^3-) and temperature (25-45 °C). Various methods including spectroscopic tests, Rietveld refinement and sequential extraction process were employed to examine the mechanisms and their contribution to As(V) removal. Results show that the As(V) removal capacity of WCP was slightly enhanced after treatment at 200 °C, the pseudo-second-order kinetics model and Langmuir model could describe the adsorption process well. The maximum uptake capacity for As(V) calculated by Langmuir model at 25, 35 and 45 °C were 31.89, 25.56 and 17.42 mg/g respectively, and the removal rate reached a maximum of 95.37% (C₀ = 100 mg/L). Thermodynamically, the As(V) elimination was exothermic and spontaneous. The ettringite produced by rehydration of WCP proved to be essential for As(V) removal. Electrostatic attraction, precipitation, complexation and ion exchange were identified to be the main mechanisms of As(V) adsorption. This study confirmed the potential of WCP in removing As(V) from wastewater and provided a new insight into the removal mechanisms.

A chitosan fiber as green material for removing Cr(VI) ions and Cu(II) ions pollutants

The application shell uses cellulose as a green and recyclable fiber material, which has great value in the field of water treatment environment. Varying factors, including pH value, dosage of CS, reaction time and original Cr(VI) ions and Cu(II) ions were studied to investigate the Cr(VI) and Cu(II) ions removal efficiency. The obtained shell trichlorocellulose has better permeability to copper ions, which is mainly due to the different oxide states of copper ions and chromium ions in a pH environment, which lead to different combinations. The price of shell cellulose neutralization is relatively low. Metal ions have better absorption properties. The kinetic and thermodynamic characteristics of the adsorption process of copper ions by chitosan yarns were discussed. The adsorption process of copper ions conformed to the quasi-second-order kinetic equation. It can be fitted by Langmuir isotherm. The adsorption of copper ions by the yarn is a spontaneous thermal reaction with both physical adsorption and chemical adsorption. Compared with chromium ions, chitosan fibers have better adsorption of copper ions, which is mainly because the amino groups in chitosan fibers can have good chelation with copper ions. SEM, FTIR, XRD were used to characterize the adsorption of copper ions by chitosan fibers, and the mechanism of the adsorption of metal ions by chitosan fibers was explored.

Simultaneous removal of nitrate, manganese, and tetracycline by Zoogloea sp. MFQ7: Adsorption mechanism of tetracycline by biological precipitation

A Mn(II) oxidizing-denitrifying and tetracycline (TC) removal bacterium Zoogloea sp. MFQ7 was isolated in this study. Nitrogen removal was 83.49% by nitrogen balance experiment. The maximum removal efficiencies of nitrate, Mn(II), and TC by strain MFQ7 within 96 h was 100.00, 74.56, and 63.59% at C/N of 2.0, pH of 7.0, Mn(II) of 20 mg L^-1, temperature of 30.0 °C, and TC of 0.2 mg L^-1. SEM illustrated that biogenic manganese oxides (BMO) was petal-like, XRD and XPS analyses confirmed that MnO₂ was the main component of BMO. Besides, the maximum adsorption capacity of BMO for TC was 52.21 mg g^-1. FTIR detected the changes in TC adsorption by BMO. Pseudo-second-order model (R² = 0.994) explained the adsorption kinetics of TC on BMO and Langmuir isotherm model (R² = 0.983) suggested that it was homogeneous adsorption, thermodynamics data (ΔG < 0, ΔH = 18.31 kJ mol^-1, ΔS = 72.8 J (mol*K)^-1) confirmed that adsorption was endothermic and spontaneous.

Central Composite Design for Adsorption of Pb(II) and Zn(II) Metals on PKM-2 Moringa oleifera Leaves

Biosorption is a very effective technique to eliminate the heavy metals present in the wastewater that utilize nongrowing biomass. The adsorption ability of the Periyakulam-2 (PKM-2) variety of Moringa Oleifera leaves (MOLs) to eliminate Pb(II) and Zn(II) ions from an aqueous solution was examined in this work. Fourier transform infrared (FTIR) spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray (EDX) analysis, X-ray powder diffraction, and Brunauer-Emmett-Teller methods were used to characterize the PKM-2 variety of MOLs. The set of variables consists of the metal ion initial concentration, a dosage of the adsorbent, and pH were optimized with the help of the response surface methodology to get maximum metal removal efficiency of lead and zinc metals using the PKM-2 MOL biosorbent. A maximum Pb(II) removal of 95.6% was obtained under the condition of initial concentration of metal ions 38 mg/L, a dosage of the adsorbent 1.5 g, and pH 4.7, and a maximum zinc removal of 89.35% was obtained under the condition of initial concentration of metal ions 70 mg/L, a dosage of the adsorbent 0.6 g, and pH 3.2. The presence of lead and zinc ions on the biosorbent surface and the functional groups involved in the adsorption process were revealed using EDX and FTIR analysis, respectively. The adsorption data were evaluated by employing different isotherm and kinetic models. Among the isotherm models, Langmuir's isotherm showed that the best fit and maximum adsorption capacities are 51.71 and 38.50 mg/g for lead and zinc, respectively. Kinetic studies showed accordance with the pseudo-second-order model to lead and zinc metal adsorption. Thermodynamic parameters confirmed (ΔG° < 0, ΔH° < 0, and ΔS° > 0) that the sorption mechanism is physisorption, exothermic, spontaneous, and favorable for adsorption. The results from this study show that the MOL of the PKM-2 type is a promising alternative for an ecofriendly, low-cost biosorbent that can effectively remove lead and zinc metals from aqueous solutions.

Biocomposites Developed with Litchi Peel Based on Epoxy Resin: Mechanical Properties and Flame Retardant

Bio-based composites are reinforced polymeric materials, which include one or two bio-based components. Biocomposites have recently attracted great attention for applications ranging from home appliances to the automotive industry. The outstanding advantages are low cost, biodegradability, lightness, availability, and solving environmental problems. In recent days, biodegradable natural fibers are attracting a great deal of interest from researchers to work on and develop a new type of composite material for diverse applications. The objective of this work is to evaluate fire resistance and mechanical properties of epoxy polymer composites reinforced with lychee peel (Vietnam), at 10 wt%, 20 wt%, and 30 wt% mass%. The study showed that the mechanical properties and flame retardancy tended to increase in the presence of lychee peel reinforcement. In the combined ratios, 20 wt% lychee rind gave a limiting oxygen index of 21.5%, with a burning rate of 23.45 mm/min. In terms of mechanical strength, in which the Izod impact strength increased by 26.46%, the compressive strength increased by 25.20% and the tensile strength increased by 20.62%. The microscopic images (SEM images) show that the particle distribution is quite good and the adhesion and wetting compatibility on the two-phase interface of lychee peel-epoxy resin are strong.

Zn2+ removal from the aqueous environment using a polydopamine/hydroxyapatite/Fe3O4 magnetic composite under ultrasonic waves

In this study, an easily magnetically recoverable polydopamine (PDA)-modified hydroxyapatite (HAp)/Fe₃O₄ magnetic composite (HAp/Fe₃O₄/PDA) was suitably synthesized to exploit its adsorption capacity to remove Zn²⁺ from aqueous solution, and its structural properties were thoroughly examined using different analytical techniques. The effect of multiple parameters like pH, ultrasonic power, ultrasonic time, adsorbent dose, and initial Zn²⁺ concentration on the adsorption efficiency was assessed using RSM-CCD. According to the acquired results, by increasing the adsorbent quantity, ultrasonic power, ultrasonic time, and pH, the Zn²⁺ adsorption efficiency increased and the interaction between the variables of ultrasonic power/Zn²⁺ concentration, pH/Zn²⁺ concentration, pH/absorbent dose, and ultrasonic time/adsorbent dose has a vital role in the Zn²⁺ adsorption. The uptake process of Zn²⁺ onto PDA/HAp/Fe₃O₄ followed Freundlich and pseudo-second order kinetic models. The maximum capacity of Zn²⁺ adsorption (q _m) obtained by PDA/HAp/Fe₃O₄, HAp/Fe₃O₄, and HAp was determined as 46.37 mg g^-1, 40.07 mg g^-1, and 37.57 mg g^-1, respectively. Due to its good performance and recoverability (ten times), the HAp/Fe₃O₄/PDA magnetic composite can be proposed as a good candidate to eliminate Zn²⁺ ions from a water solution.

Banana Fiber-Reinforced Epoxy Composites: Mechanical Properties and Fire Retardancy

Currently, the growing field of technology has paved the way for using environmental friendly resources; in particular, plant origin holds ecological concern and renewable aspects. Currently, natural fiber composites have widening attention, thanks to their eco-friendly properties. In the present work, the composite material is reinforced with natural fibers from the bark of banana trees (banana fibers), a material available in Vietnam. Banana fibers are extracted from banana peels, pretreated with NaOH 5%, and then cut to an average length of 30 mm. Banana fiber is reinforced for epoxy resin Epikote 240 with mass percents: 10 wt.%, 15 wt.%, 20 wt.%, and 25 wt.%. The results were evaluated through structural morphology (SEM), mechanical properties, fire resistance, and thermal properties. Experimental results show that the tensile, compressive, and impact strengths of biosynthetic materials up to 20% by weight have increased compared to epoxy neat. Flame retardant and thermal properties are kept stable; 20 wt.% banana fiber gives a limiting oxygen index of 20.8% and satisfactory thermal stability.

Hybrid Biocomposites Based on Used Coffee Grounds and Epoxy Resin: Mechanical Properties and Fire Resistance

Studies on using biomaterials hybridized with other materials to produce biomaterials have been paid more attention due to their low cost, abundance, renewability, and degradability. Therefore, these materials are ecofriendly and nontoxic to humans. A large number of used coffee grounds (SCGs) are often discarded and replacements are necessary for dealing with environmental problems. This work developed sustainable materials by reusing SCGs. Used coffee grounds were mixed with epoxy resin at different amounts: 30 wt %, 40 wt %, 50 wt %, and 60 wt %. SCGs were treated with 0.5 N NaOH, at SCGs/NaOH ratio of 1 : 2. SEM images showed that the material with 30 wt % SCGs has good compatibility without phase division on the SCGs-epoxy interface. Results of mechanical properties of epoxy composites with 30 wt % SCGs are as follows: tensile strength of 44.81 ± 10 MPa, flexural strength of 80.07 ± 0.16 MPa, compressive strength of 112.56 ± 0.11 MPa, and Izod strength and impact of 8.21 ± 0.19 kJ/m2. In terms of flame-retardant properties, the oxygen index is limited to 20.8% ± 0.20 and the burning rate according to UL94HB is 27.02 ± 0.29 mm/min. The obtained results indicate that it is possible to produce biohybrid composites from epoxy resin and SCGs. This work offers an ecofriendly alternative method to use the waste of the coffee industry. It contributes to improvements of the general characteristics of composites such as mechanical, thermal, and flame-retardant properties. This work proved that SCGs have a high potential to be used in a wide range of composite materials for civil engineering applications.

Adsorption of Crystal Violet Dye Using Activated Carbon of Lemon Wood and Activated Carbon/Fe3O4 Magnetic Nanocomposite from Aqueous Solutions: A Kinetic, Equilibrium and Thermodynamic Study

Activated carbon prepared from lemon (Citrus limon) wood (ACL) and ACL/Fe₃O₄ magnetic nanocomposite were effectively used to remove the cationic dye of crystal violet (CV) from aqueous solutions. The results showed that Fe₃O₄ nanoparticles were successfully placed in the structure of ACL and the produced nanocomposites showed superior magnetic properties. It was found that pH was the most effective parameter in the CV dye adsorption and pH of 9 gave the maximum adsorption efficiency of 93.5% and 98.3% for ACL and ACL/Fe₃O₄, respectively. The Dubinin–Radushkevich (D-R) and Langmuir models were selected to investigate the CV dye adsorption equilibrium behavior for ACL and ACL/Fe₃O₄, respectively. A maximum adsorption capacity of 23.6 and 35.3 mg/g was obtained for ACL and ACL/Fe₃O₄, respectively indicating superior adsorption capacity of Fe₃O₄ nanoparticles. The kinetic data of the adsorption process followed the pseudo-second order (PSO) kinetic model, indicating that chemical mechanisms may have an effect on the CV dye adsorption. The negative values obtained for Gibb’s free energy parameter (−20 < ΔG < 0 kJ/mol) showed that the adsorption process using both types of the adsorbents was physical. Moreover, the CV dye adsorption enthalpy (ΔH) values of −45.4 for ACL and −56.9 kJ/mol for ACL/Fe₃O₄ were obtained indicating that the adsorption process was exothermic. Overall, ACL and ACL/Fe₃O₄ magnetic nanocomposites provide a novel and effective type of adsorbents to remove CV dye from the aqueous solutions.