Quantification of selected microplastics in Australian urban road dust

Airborne transboundary microplastics-A Swirl around the globe

Microplastics are persistent pollutants discovered and extensively researched in marine, freshwater, and terrestrial ecosystems but have yet to receive attention in an atmospheric context. Although recent reports stated the presence of microplastics in the air, their global existence and distribution are not critically discussed to date. This review aimed to investigate the current status of research on atmospheric microplastics through bibliometric analysis and by comparing and summarising published research on global distribution. The review also provides a summary of methods that have been used to collect samples, identify microplastics, quantify their occurrence, and determine their transport mechanisms. The bibliometric analysis revealed that atmospheric microplastic studies predominantly originated in China. Clothing, vehicle, and tire materials were the major primary sources while house furniture, construction materials, landfills, urban dust, plastic recycling processes, and agricultural sludge were precursor secondary sources. Polyethylene, polypropylene, and polyethylene terephthalate microfibres have most frequently found in indoor and outdoor atmospheres. Level of urbanization and temporal or spatial distributions governs the fate of airborne microplastics, however, the knowledge gap in the retention and circulation of microplastics through the atmosphere is still large. Many challenges and limitations were identified in the methods used, presentation of data, aerodynamic processes facilitating atmospheric transport, and scarcity of research in spatially and temporally diverse contexts. The review concluded that there was a greater need for globalization of research, methods and data standardization, and emphasizes the potential for future research with atmospheric transportation modelling and thermochemical analysis.

Microplastic distribution and their abundance along rivers are determined by land uses and sediment granulometry

Microplastics in freshwater ecosystems have gained attention for their potential impact on biodiversity. Rivers are complex and dynamic ecosystems that transport particles and organic matter from the headwaters through watersheds to the ocean. Changes in land use and the presence of wastewater treatment plants (WWTPs) increase the risk of plastic contamination. Simultaneously, hydromorphological features of the watershed can influence the dispersion and retention of microplastics. This study assesses the impact of urban land uses and river hydromorphology on microplastic abundance and spatial distribution in two watersheds with contrasting land uses. Unexpectedly, our findings show that microplastics were widespread throughout watersheds both in water (3.5 ± 3.3 particles/L) and sediments (56.9 ± 39.9 particles/g). The concentration of microplastics in sediments significantly increased in granulometry ranging from 0.5 to 1 mm. Microplastics in running waters are significantly correlated with increasing urban land use coverage. However, the presence and distance of WWTPs did not affect microplastic distribution. In conclusion, contrasting patterns were observed for suspended and sedimented microplastic particles: suspended microplastics were associated with an anthropogenic effect, whereas the concentration of microplastics in sediments was determined by riverbed granulometry. Our results suggest that the interaction of anthropogenic and environmental factors shapes microplastic distribution along the rivers and their subsequent transport toward the coastal ocean. Finally, a review of the current literature reveals the absence of standardization in field and laboratory assessment techniques and measurement units, representing a challenge for intercomparisons of river microplastic studies.

Source traceability of microplastics in road dust using organic/inorganic plastic additives as chemical indicators

Microplastics (MPs) are environmental pollutants of great concern around the world. The source of MPs in road dust need to be identified to develop strategies to control and reduce MPs emissions by stormwater runoff, one of the main sources of MPs to the aquatic environment. However, little information on the sources of MPs in road dust is available due to lack of their suitable indicators. In this study organic/inorganic plastic additives were used as chemical indicators to understand the source of MPs in road dust. The polymers, organic additives, and heavy metals in 142 commercial plastic products suspected of being source of MPs in road dust were determined. As the results, 147 organic additives and 17 heavy metals were identified, and different additive profiles were found for different polymer types and use application of plastic products. Further, 17 road dust samples were collected from an urban area in Kumamoto City, Japan. and analyzed the MPs (1-5 mm diameter) and their additive chemicals. Polymethyl methacrylate (PMMA) was the dominant polymer accounting for 86 % in the samples, followed by ethylene vinyl acetate (EVA) and polyvinyl chloride (PVC). In total, 48 organic additives and 14 heavy metals were identified in the MPs samples. The organic/inorganic additive profiles of plastic products and MPs in road dust were compared, and several road dust-associated MPs had similar additive profiles to road paints, braille blocks, road marking sheets, and reflectors. This suggested that the MPs were originated from these plastics on the road surface. Road paint was the most important contributor of MPs in road dust (60 % of the MPs), followed by braille block (23 %), road marking sheet (8.3 %), and reflector (2.4 %). These results indicated that organic/inorganic plastic additives in plastic products can be used as chemical indicators to trace the sources of MPs in road dust.

Bark and biochar in horizontal flow filters effectively remove microplastics from stormwater

Organic materials such as bark and biochar can be effective filter materials to treat stormwater. However, the efficiency of such filters in retaining microplastics (MPs) - an emerging stormwater pollutant - has not been sufficiently studied. This study investigated the removal and transport of a mixture of MPs commonly associated with stormwater. Different MP types (polyamide, polyethylene, polypropylene, and polystyrene) were mixed into the initial 2 cm material of horizontal bark and biochar filters of 25, 50, and 100 cm lengths. The MP types consisted of spherical and fragmented shapes in size ranges of 25-900 μm. The filters were subjected to a water flow of 5 mL/min for one week, and the total effluents were analyzed for MPs by μFTIR imaging. To gain a deeper insight, one 100 cm bark filter replica was split into 10 cm segments, and MPs in each segment were extracted and counted. The results showed that MPs were retained effectively, >97%, in all biochar and bark filters. However, MPs were detected in all effluents regardless of filter length. Effluent concentrations of 5-750 MP/L and 35-355 MP/L were measured in bark and biochar effluents, respectively, with >91% of the MP counts consisting of small-sized (25 μm) polyamide spherical particles. Combining all data, a decrease in average MP concentration was noticed with longer filters, likely attributed to channeling in a 25 and 50-cm filter. The analyses of MPs in the bark media revealed that most MPs were retained in the 0-10 cm segment but that some MPs were transported further, with 19% of polyamide retained in the 80-90 cm segment. Overall, this study shows promising results for bark and biochar filters to retain MPs, while highlighting the importance of systematic packing of filters to reduce MP emissions to the environment from polluted stormwater.

Artificial intelligence-empowered collection and characterization of microplastics: A review

Microplastics have been detected from water and soil systems extensively, with increasing evidence indicating their detrimental impacts on human and animal health. Concerns surrounding microplastic pollution have spurred the development of advanced collection and characterization methods for studying the size, abundance, distribution, chemical composition, and environmental impacts. This paper offers a comprehensive review of artificial intelligence (AI)-empowered technologies for the collection and characterization of microplastics. A framework is presented to streamline efforts in utilizing emerging robotics and machine learning technologies for collecting, processing, and characterizing microplastics. The review encompasses a range of AI technologies, delineating their principles, strengths, limitations, representative applications, and technology readiness levels, facilitating the selection of suitable AI technologies for mitigating microplastic pollution. New opportunities for future research and development on integrating robots and machine learning technologies are discussed to facilitate future efforts for mitigating microplastic pollution and advancing AI technologies.

Understanding the Dynamics of Microplastics Transport in Urban Stormwater Runoff: Implications for Pollution Control and Management

The transport of microplastics (MPs) from urban environments to water resources via stormwater runoff poses significant concerns due to its adverse impacts on water safety and aquatic ecosystems. This study presents a modeling approach aimed at understanding the transport mechanisms of MPs in an urban residential setting, considering settling and buoyant MPs. To consider the effect of MP shapes, the settling velocity of various settling MPs in shapes of fibers, films, and fragments was calculated. Using an analogy of sediment transport, a Rouse number criterion was used to analyze the transport of MPs. For buoyant MPs, it was assumed that they transport as wash-load as soon as they float in the water and the travel time for them to reach the storm drain was determined. The calculation of settling velocity revealed the influence of shape on the settling velocity of MPs was particularly pronounced as the equivalent diameter of the MPs increased. The transport mechanism for the smallest settling MPs, irrespective of their shapes, density, and depth of flow, was wash-load. However, for larger MPs, the shape and size distribution of settling MPs, along with the depth of flow and slope significantly influenced their transport mechanisms compared to sediment particles. The influence of weathering on the MPs' transport mechanisms depended on their sizes and shapes. The site-specific characteristics, including slope and surface friction, significantly influenced the velocity of stormwater runoff and, consequently, the extent of MP transport during rain events. Moreover, an evaluation of the transport mechanism of settling MPs was conducted using the reported field data on MP abundance in road dust collected from residential and traffic sites. This study underscores the complexity of MP transport dynamics and provides a foundation for developing targeted strategies to mitigate MP pollution in urban environments.

An explicit review and proposal of an integrated framework system to mitigate the baffling complexities induced by road dust-associated contaminants

Road dust-associated contaminants (RD-AC) are gradually becoming a much thornier problem, as their monotonous correlations render them carcinogenic, mutagenic, and teratogenic. While many studies have examined the harmful effects of road dust on both humans and the environment, few studies have considered the co-exposure risk and gradient outcomes given the spatial extent of RD-AC. In this spirit, this paper presents in-depth elucidation into the baffling complexities induced by both major and emerging contaminants of road dust through a panorama-to-profile up-to-date review of diverse studies unified by the goal of advancing innovative methods to mitigate these contaminants. The paper thoroughly explores the correlations between RD-AC and provides insights to understand their potential in dispersing saprotrophic microorganisms. It also explores emerging challenges and proposes a novel integrated framework system aimed at thermally inactivating viruses and other pathogenic micro-organisms commingled with RD-AC. The main findings are: (i) the co-exposure risk of both major and emerging contaminants add another layer of complexity, highlighting the need for more holistic framework strategies, given the geospatial morphology of these contaminants; (ii) road dust contaminants show great potential for extended prevalence and severity of viral particles pollution; (iii) increasing trend of environmentally persistent free radicals (EPFRs) in road dust, with studies conducted solely in China thus far; and (iv) substantial hurdle exists in acquiring data concerning acute procedural distress and long-term co-exposure risk to RD-ACs. Given the baffling complexities of RD-ACs, co-exposure risk and the need for innovative mitigation strategies, the study underscore the significance of establishing robust systems for deep road dust contaminants control and future research efforts while recognizing the interconnectivity within the contaminants associated with road dust.

Tire plastic and road-wear particles on Yujing Expressway in the restoration area of Mu Us Sandy Land: Occurrence characteristics and ecological risk screening

Tire plastic and road-wear particles (TPR-WP) are a current research priority as one of the main environmental sources of microplastics. We selected a unique land use type - desert restoration area, collected soil and dust samples from the Yujing Expressway and its service areas, and analyzed TPR-WP abundance, type, size and morphology by laser direct infrared (LDIR). The abundance of TPR-WP in expressway dust (14,446.87 ± 10,234.24 n/kg) was higher than that in soil (7500 ± 3253.64 n/kg). Random forest model showed that the source of TPR-WP was highly correlated with economic factors and natural climate. Overall, the proportion of small and medium-sized TPR-WP in dust was higher than soil, more than half of the TPR-WP in dust were in 20 - 50 µm range. The proportion of small particle size TPR-WP increased with the rise of elevation. The pollution load index suggested that the survey region was generally at level I risk zone, while the ecological risk index indicated that the pollution level of expressway was III and IV, and the service area was IV. In general, the study was of great significance for clarifying the distribution and risk of TPR-WP in soil and dust of expressways and service areas.

Are we underestimating stormwater? Stormwater as a significant source of microplastics in surface waters

Stormwater represent a critical pathway for transporting microplastics (MPs) to surface waters. Due to complex dynamics of MPs in stormwater, its dispersion, weathering, risk, and transport are poorly understood. This review bridges those gaps by summarizing the latest findings on sources, abundance, characteristics, and dynamics involved in stormwater MP pollution. Weathering starts before or after MPs enter stormwater and is more pronounced on land due to continuous heat and mechanical stress. Land use patterns, rainfall intensity, MPs size and density, and drainage characteristics influence the transport of MPs in stormwater. Tire and road wear particles (TRWPs), littering, and road dust are major sources of MPs in stormwater. The concentrations of MPs varies from 0.38-197,000 particles/L globally. Further MP concentrations showed regional variations, highlighting the importance of local monitoring efforts needed to understand local pollution sources. We observed unique signatures associated with the shape and color of MPs. Fibers and fragments were widely reported, with transparent and black being the predominant colors. We conclude that the contribution of stormwater to MP pollution in surface waters is significantly greater than wastewater treatment plant effluents and demands immediate attention. Field and lab scale studies are needed to understand its behavior in stormwater and the risk posed to the downstream water bodies.

A comprehensive review of micro- and nano-plastics in the atmosphere: Occurrence, fate, toxicity, and strategies for risk reduction

Micro- and nano-plastics (MNPs) have received considerable attention over the past 10 years due to their environmental prevalence and potential toxic effects. With the increase in global plastic production and disposal, MNP pollution has become a topic of emerging concern. In this review, we describe MNPs in the atmospheric environment, and potential toxicological effects of exposure to MNPs. Studies have reported the occurrence of MNPs in outdoor and indoor air at concentrations ranging from 0.0065 items m-3 to 1583 items m-3. Findings have identified plastic fragments, fibers, and films in sizes predominantly <1000 μm with polyamide (PA), polyester (PES), polyethylene terephthalate (PET), polypropylene (PP), rayon, polyethylene (PE), polystyrene (PS), polyvinyl chloride (PVC), polyacrylonitrile (PAN), and ethyl vinyl acetate (EVA) as the major compounds. Exposure through indoor air and dust is an important pathway for humans. Airborne MNPs pose health risks to plants, animals, and humans. Atmospheric MNPs can enter organism bodies via inhalation and subsequent deposition in the lungs, which triggers inflammation and other adverse health effects. MNPs could be eliminated through source reduction, policy/regulation, environmental awareness and education, biodegradable materials, bioremediation, and efficient air-filtration systems. To achieve a sustainable society, it is crucial to implement effective strategies for reducing the usage of single-use plastics (SUPs). Further, governments play a pivotal role in addressing the pressing issue of MNPs pollution and must establish viable solutions to tackle this significant challenge.

Quantification of nanoplastics uptake and transport in lettuce by pyrolysis gas chromatography-mass spectrometry

Nanoplastics (NPs) can enter the edible parts of crop and threaten human health, which attract widespread attention. However, the precise quantification of NPs in crop is still a tremendous challenge. Herein, a method with Tetramethylammonium hydroxide (TMAH) digestion, dichloromethane extraction combined with pyrolysis gas chromatography-mass spectrometry (Py-GC/MS) quantification was present to quantify polystyrene (PS) NPs uptake in lettuce (Lactuca sativa). 25% of TMAH was optimized as extraction solvent and 590 °C was selected as pyrolysis temperature. Recoveries of 73.4-96.9% were obtained for PS-NPs at spiking level of 4-100 μg/g in control samples (RSD < 8.6%). The method exhibited good intra-day and inter-day reproducibility, detection limits of 34-38 ng/g and linearity with 0.998-0.999. The reliability of Py-GC/MS method was verified by europium-chelated PS using inductively coupled plasma mass spectrometry (ICP-MS). To simulate different environmental conditions, hydroponic culture and soil incubated lettuce were exposed to different concentrations of NPs. Higher levels of PS-NPs were detected in roots and very few was transferred to the shoots. NPs in lettuce were confirmed by laser scanning confocal microscopy (LSCM). The developed method provides new opportunities for the quantification of NPs in crops.

Microplastics in environment: a comprehension on sources, analytical detection, health concerns, and remediation

Contamination of ecosystems by microplastics (MPs) has been reported intensively worldwide in the recent decade. A trend of reports indicated their presence in the atmosphere; food items and soil ecosystems are rising continuously. Literature evidenced that MPs are abundant in seawater, beach sand, drinking water, agricultural soils, wastewater treatment plant (WWTP) effluent, and the atmosphere. The greater abundance of MPs in the environment has led to their invasion of seafood, human-consumed food items such as table salts, beverages, takeout food containers, and disposable cups, marine biological lives, and creating serious health hazards in humans. Moreover, the absence of guidelines and specifications for controlling MPs in the environment makes the situation alarming, and the human toxicity data of MPs is scarce. Thereby, the toxicity assessment of MPs in humans is of greater concern. This review compiles the updated information on the potential sources of MPs in different components of the environment (viz. soil, water, and air), their analysis methods, effects on human health, and remediation methods.

High-Content Screening Discovers Microplastics Released by Contact Lenses under Sunlight

The widespread use of plastic products leads to the ubiquity of microplastics in daily life, while the release of microplastics from long-used contact lenses has not been reported due to the limitations of conventional detection methods. Here, we established a new and rapid method to capture and count microplastics by using a high-content screening system. This method can simultaneously measure the diameter, area, and shape of each plastic particle, and the reliability and applicability of this method were verified with commercial microplastics. It is estimated that 90,698 particles of microplastics could be released from a pair of contact lenses during a year of wearing. The microplastics in the leachates were confirmed to be released from the contact lenses by scanning electron microscopy and Fourier transform infrared spectroscopy fingerprint analysis. Our study reveals an undiscovered pathway of microplastic direct exposure to humans, highlighting the urgent need to assess the potential health risks caused by eye exposure to microplastics.

There's something in the air: A review of sources, prevalence and behaviour of microplastics in the atmosphere

Literature regarding microplastics in the atmosphere has advanced in recent years. However, studies have been undertaken in isolation with minimal collaboration and exploration of the relationships between air, deposition and dust. This review collates concentrations (particle count and mass-based), shape, size and polymetric characteristics for microplastics in ambient air (m3), deposition (m2/day), dust (microplastics/g) and snow (microplastics/L) from 124 peer-reviewed articles to provide a holistic overview and analysis of our current knowledge. In summary, ambient air featured concentrations between <1 to >1000 microplastics/m³ (outdoor) and <1 microplastic/m³ to 1583 ± 1181 (mean) microplastics/m³ (indoor), consisting of polyethylene terephthalate, polyethylene, polypropylene. No difference (p > 0.05) was observed between indoor and outdoor concentrations or the minimum size of microplastics (p > 0.5). Maximum microplastic sizes were larger indoors (p < 0.05). Deposition concentrations ranged between 0.5 and 1357 microplastics/m²/day (outdoor) and 475 to 19,600 microplastics/m²/day (indoor), including polyethylene, polystyrene, polypropylene, polyethylene terephthalate. Concentrations varied between indoor and outdoor deposition (p < 0.05), being more abundant indoors, potentially closer to sources/sinks. No difference was observed between the minimum or maximum reported microplastic sizes within indoor and outdoor deposition (p > 0.05). Road dust concentrations varied between 2 ± 2 and 477 microplastics/g (mean), consisting of polyvinyl chloride, polyethylene, polypropylene. Mean outdoor dust concentrations ranged from <1 microplastic/g (remote desert) to between 18 and 225 microplastics/g, comprised of polyethylene terephthalate, polyamide, polypropylene. Snow concentrations varied between 0.1 and 30,000 microplastics/L, containing polyethylene, polyamide, polypropylene. Concentrations within indoor dust varied between 10 and 67,000 microplastics/g, including polyethylene terephthalate, polyethylene, polypropylene. No difference was observed between indoor and outdoor concentrations (microplastics/g) or maximum size (p > 0.05). The minimum size of microplastics were smaller within outdoor dust (p > 0.05). Although comparability is hindered by differing sampling methods, analytical techniques, polymers investigated, spectral libraries and inconsistent terminology, this review provides a synopsis of knowledge to date regarding atmospheric microplastics.

Microplastic pollution in sediments of urban rainwater drainage system

The sink of microplastics (MPs) in sediments of urban rainwater drainage system (RDS) is of great concern, because the MPs deposited can be resuspended by flow disturbance. Previous research has confirmed the significant accumulation of MPs in sediments of urban RDS, but it remains poorly elucidated, such as pollution sources and influencing factors. In this study, we investigated the MPs in sediments from RDS of a university campus. MPs were detected from all sediment samples, showing the ubiquity of microplastic pollution. Among 11 samples MPs' abundance ranged from 80 to 2610 particles/kg (dry weight), with highly spatial variability, depending on land type and environmental management practice within the catchment. Sites from office & teaching area had the averaged abundance of 335.00 ± 196.85 particles/kg, while 270.00 ± 89.09 particles/kg for staff residential area, and 795.00 ± 1050.65 particles/kg for student living area, indicating that the sediments of RDS from student living area had the highest abundance of MPs. However, independent sample t-test analysis suggests there is no statistically significant difference between land types, because of effective environmental management practices in the catchment. The surfaces of MPs were much rough, which implies that the fragmentation of larger plastic particles resulted in the production of MPs. Although the MPs of <1000 μm were the most, 1000-2000 μm MPs also accounted for a significant proportion in this study, showing a slight difference from the previous study in which MPs over 1 mm were quite low. Polypropylene (PP) and polyester (PET) found to be dominant with 49.75 ± 18.69 % and 49.75 ± 18.69 % of the total number, respectively. As to shapes, the proportion of fiber and fragment MPs exceeded 80 %. The color of MPs diversified greatly, and the MPs with bright colors occupied over 80 %. Fabric fibers, food packaging and courier packaging materials were figured out to be the considerable contributors of MPs.

Sources, Fate, and Detection of Dust-Associated Perfluoroalkyl and Polyfluoroalkyl Substances (PFAS): A Review

The occurrence of sand and dust storms (SDSs) is essential for the geochemical cycling of nutrients; however, it is considered a meteorological hazard common to arid regions because of the adverse impacts that SDSs brings with them. One common implication of SDSs is the transport and disposition of aerosols coated with anthropogenic contaminants. Studies have reported the presence of such contaminants in desert dust; however, similar findings related to ubiquitous emerging contaminants, such as per- and poly-fluoroalkyl substances (PFAS), have been relatively scarce in the literature. This article reviews and identifies the potential sources of dust-associated PFAS that can accumulate and spread across SDS-prone regions. Furthermore, PFAS exposure routes and their toxicity through bioaccumulation in rodents and mammals are discussed. The major challenge when dealing with emerging contaminants is their quantification and analysis from different environmental media, and these PFAS include known and unknown precursors that need to be quantified. Consequently, a review of various analytical methods capable of detecting different PFAS compounds embedded in various matrices is provided. This review will provide researchers with valuable information relevant to the presence, toxicity, and quantification of dust-associated PFAS to develop appropriate mitigation measures.

Atmospheric microplastics: exposure, toxicity, and detrimental health effects

Microplastics (MPs) are micro-particulate pollutants present in all environments whose ubiquity leads humans to unavoidable exposure. Due to low density, MPs also accumulate in the atmosphere, where they are easily transported worldwide and come into direct contact with the human body by inhalation or ingestion, causing detrimental health effects. This literature review presents the sources of atmospheric MPs pollution, transport routes, physicochemical characteristics, and environmental interactions. The document also explains the implications for human health and analyzes the risk of exposure based on the potential toxicity and the concentration in the atmosphere. MPs' toxicity lies in their physical characteristics, chemical composition, environmental interactions, and degree of aging. The abundance and concentration of these microparticles are associated with nearby production sources and their displacement in the atmosphere. The above elements are presented in an integrated way to facilitate a better understanding of the associated risk. The investigation results encourage the development of future research that delves into the health implications of exposure to airborne MPs and raises awareness of the risks of current plastic pollution to promote the establishment of relevant mitigation policies and procedures.

Mass quantification of microplastic at wastewater treatment plants by pyrolysis-gas chromatography-mass spectrometry

Municipal wastewater treatment plants (WWTPs) are a central point of collection of plastic particles from households and industry and for their re-distribution into the environment. Existing studies evaluating levels of plastics in WWTPs, and their removal rates have reported and used data on polymer type, size, shape, colour, and number of plastic particles, while the total mass concentration of plastic particles (especially >1 μm) remains unclear and unknown. To address this knowledge gap, raw influent, effluent, and reference water samples from three WWTPs in Australia were collected to analyse the mass concentrations and removal rates of seven common plastics (>1 μm in size) across the treatment schemes. Quantitative analysis was performed by pressurized liquid extraction followed by pyrolysis coupled to gas chromatography mass spectrometry. Results showed that the total plastic content in the WWTPs raw influent samples was between 840 and 3116 μg/L, resulting in an inflow of between about 2.1 and 196.4 kg/day of the total measured plastics. Overall, >99 % by mass of the plastics entering the three WWTPs from the raw influent was removed during the pre-treatment stages, presumably ending up in the sewage sludge, which means emissions (via treated effluent) from the treatment plants are low. Compared with the raw influent, the plastic mass concentrations in the treated effluents (i.e., Class C, A, and final effluent) from the three WWTPs, as well as the reference water samples within their catchments were below the limits of reporting. Of the five quantified plastic types, polyethylene (PE, 76.4 %), and polyvinylchloride (PVC, 21 %) dominated by mass, while polyethylene terephthalate (PET, 1.9 %), polypropylene (PP, 0.4 %) and polymethyl methacrylate (PMMA, 0.3 %) accounted for a small proportion of the total. Overall, this study investigated the mass concentrations of plastic particles above 1 μm in wastewater and their removal, which provided valuable information regarding the pollution level and distribution characteristics of plastic polymers in Australian WWTPs.

Microplastics in urban freshwater streams in Adelaide, Australia: A source of plastic pollution in the Gulf St Vincent

The pollution of marine environments from plastic waste is anticipated to increase with current increases in plastic production. Reciprocally, escalating research efforts provide an improved understanding, monitoring, awareness, and mitigation of plastic contamination. Freshwater streams are recognised as one of the main contributors of microplastic pollution in marine environments. Presented here is the first investigation on the abundance of microplastic contamination (>20 μm and <5 mm) in freshwater streams in Adelaide, Australia. Composite samples were obtained from the sub-surface waters of eight freshwater streams (Magazine Wetland, Torrens River, Brownhill Creek, Sturt River, Field River, Christie Creek, Onkaparinga River and Pedler Creek), just before their connection to the Gulf St Vincent. Microplastics were found in all samples and microplastic abundance was 6.4 ± 5.5 particles.L^-1 across all streams, with significant variations. Microplastic abundances found in the freshwater streams of Adelaide were comparatively higher than those found in areas of similar urbanisation, likely due to the varying methodologies used across studies. This work provides evidence, for the first time, of the prevalence of microplastic contamination in the sub-surface waters of eight freshwater streams in metropolitan Adelaide. These findings reinforce the need for long-term and on-going monitoring of freshwater streams for plastic contamination. Furthermore, spatial and temporal monitoring will allow for the identification in changes to the abundances of microplastics discharging from these sources into the Gulf St Vincent and observe if abundances increase or decrease with any future targeted waste management efforts.

Children's playgrounds contain more microplastics than other areas in urban parks

Children spend many hours in urban parks and playgrounds, where the tree canopy could filter microplastics released from the surrounding urban hotspots. However, the majority of children's playgrounds also contain plastic structures that could potentially release microplastics. To assess if the children's playgrounds pose a higher exposure risk than other places inside the park, we evaluate the extent of microplastic contamination in the sand, soil, and leaf samples from 19 playgrounds inside urban parks in Los Angeles, CA, USA. The average microplastic concentration in sand samples collected inside the playground was 72 p g-1, and >50 % of identified plastics were either polyethylene or polypropylene. Microplastic concentrations inside the playgrounds were on average >5 times greater than concentrations outside the playgrounds in the park, indicating that children playing within the playground may be exposed to more microplastics than children playing outside the playground in the same park. By comparing the microplastic composition found inside and outside the playgrounds with the plastic composition of the plastic structures in the playground, we show that plastic structures and other products used inside the playgrounds could contribute to elevated microplastic concentration. The population density was slightly correlated with a microplastic concentration in the park soil but did not correlate with microplastic concentration inside the playgrounds. Therefore, playgrounds in urban parks may have microplastic exposure risks via inhalation or ingestion via hand-to-mouth transfer.

Mass Spectrometry as an Analytical Tool for Detection of Microplastics in the Environment

Plastic particles smaller than 5 mm accumulate in aqueous, terrestrial, and atmospheric environments and their discovery has been a serious concern when it comes to eco-toxicology and human health risk assessment. In the following review, the potential of mass spectrometry (MS) for the detection of microplastic (MP) pollutants has been elaborately reviewed. The use of various mass spectrometric techniques ranging from gas chromatography–mass spectrometry (GC-MS), liquid chromatographic mass spectrometric (LC-MS) to matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS), including their variants, have been reviewed. The lapses in the detection system have been addressed and future recommendations proposed. The challenges facing microplastics and their detection have been discussed and future directions, including mitigation methods, have been presented.

Polystyrene Nanoplastics Induce Lung Injury via Activating Oxidative Stress: Molecular Insights from Bioinformatics Analysis

(1) Background: Increasing evidence reveals that airborne plastic particles will continue to degrade into nanoplastics which are then inhaled by humans, causing injury to the respiratory system with controversial molecular mechanisms. (2) Methods: We used polystyrene nanoplastics (PS-NPs) as the representative pollutants to explore the inhalation toxicology of nanoplastics and identified the potential mechanism through high-throughput sequencing. (3) Results: PS-NPs inhibited cell viability in a dose-dependent manner and 0 μg/cm², 7.5 μg/cm² and 30 μg/cm² PS-NP-treated groups were selected for RNA-seq. Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) analysis suggested that lung injuries caused by PS-NPs were mediated via redox imbalance, which was verified by reactive oxygen species (ROS) staining. Additionally, we obtained ten key transcription factors (TFs) governing differentially expressed genes (DEGs), nine of which were involved in the regulation of oxidative stress. An oxidative stress-associated TF-mRNA regulatory network was constructed on account of the findings above. Further joint analysis with animal experiment data from the GEO database identified a crucial oxidative stress-related molecule, TNFRSF12A. qRT-PCR was performed to confirm the results of RNA-seq. (4) Conclusions: Our study indicates the potential role of oxidative stress in the mechanism of nanoplastics-induced lung injuries, with several key genes being promising targets to analyze in future investigations.

Identification and Quantification of Micro-Bioplastics in Environmental Samples by Pyrolysis-Gas Chromatography-Mass Spectrometry

Bioplastics are materials that are biobased and/or biodegradable, but not necessarily both. Concerns about environmental plastic pollution are constantly growing with increasing demand for substituting fossil-based plastics with those made using renewable resource feedstocks. For many conventional bioplastics to completely decompose/degrade, they require specific environmental conditions that are rarely met in natural ecosystems, leading to rapid formation of micro-bioplastics. As global bioplastic production and consumption/use continue to increase, there is growing concern regarding the potential for environmental pollution from micro-bioplastics. However, the actual extent of their environmental occurrence and potential impacts remains unclear, and there is insufficient mass concentration-based quantitative data due to the lack of quantitative analytical methods. This study developed and validated an analytical method coupling pressurized liquid extraction and pyrolysis-gas chromatography-mass spectrometry combined with thermochemolysis to simultaneously identify and quantify five targeted micro-bioplastics (i.e., polylactic acid (PLA), polyhydroxyalkanoate, polybutylene succinate, polycaprolactone, and polybutylene adipate terephthalate (PBAT)) in environmental samples on a polymer-specific mass-based concentration. The recovery of spiked micro-bioplastics in environmental samples (biosolids) ranged from 74 to 116%. The limits of quantification for the target micro-bioplastics were between 0.02 and 0.05 mg/g. PLA and PBAT were commonly detected in wastewater, biosolids, and sediment samples at concentrations between 0.07 and 0.18 mg/g. The presented analytical method enables the accurate identification, quantification, and monitoring of micro-bioplastics in environmental samples. This study quantified five micro-bioplastic types in complex environmental samples for the first time, filling in gaps in our knowledge about bioplastic pollution and providing a useful methodology and important reference data for future research.

Microplastics in urban soils of Nanjing in eastern China: Occurrence, relationships, and sources

Although microplastic (MP) pollution has been defined as a new global challenge by the United Nations Environment Programme, their abundance and composition has only been studied in-depth within farmland soil, while minimal attention has been placed on urban soil contamination. Accordingly, within the current study, MP abundance and composition is investigated within urban soil from green spaces in Nanjing, eastern China. The average MP abundance in soil was 461 ± 222 items/kg and primarily comprised fibers (39.1%) and fragments (37.7%). MPs <1000 μm in size accounted for 83.7% of the total content and white MPs were the most abundant (26.5%). The dominant polymers were polyethylene glycol terephthalate (32.0%) and polypropylene (20.5%). Moreover, relationship network analysis generated three distinct MP modules based on community similarity. Indeed, the degree of similarity increased by ∼26.8% per kilometer. Furthermore, application of a forward selective optimal multiple regression model identified clay, sand, longitude, and points of interest for recycling bins (RecyclePOI) as the primary spatial and soil environmental factors affecting MP abundance and composition. Additionally, five potential sources of MPs were identified based on the MP diversity integrated index fitting results, and point of interest density (MDII-POI) source analysis (R² = 0.21-0.62; P < 0.05). In particular, the point of interest of express delivery points (ExpressPOI) were important sources of plastic emissions as they are widely distributed throughout urban and fringe areas. Collectively, the findings of this study provide novel insights regarding quantitative source appointment and regional ecological control of MPs in urban soil.

Microplastic Contamination in Urban, Farmland and Desert Environments along a Highway in Southern Xinjiang, China

The different types of microplastics (MPs), including debris, fibers, particles, foams, films and others, have become a global environmental problem. However, there is still a lack of research and understanding of the pollution characteristics and main causes of MPs in the arid region of Xinjiang, China. In this survey, we focused on the occurrence and distribution of MPs in urban, farmland and desert areas along a highway in the survey area. Our results showed that the main types of MPs were polypropylene (PP) flakes, polyethylene (PE) films and both PE and PP fragments and fibers. The abundance levels of MPs in street dust of Korla, Alar and Hotan districts equaled 804, 307 and 1526 particles kg−1, respectively, and were positively correlated with the urban population. In farmland areas, there were only two types of MPs (films and fibers), of which the film particles dominated and accounted for 91% of the total on the average. The highest abundance rate of MPs reached 7292 particles kg−1 in the desert area along the highway. The minimum microplastic particle sizes were 51.8 ± 2.2 μm in urban street dust samples, 54.2 ± 5.3 μm in farmland soil samples and 67.8 ± 8.4 μm in samples from along the desert highway. Particle sizes < 500 μm were most common and accounted for 48−91% of the total in our survey. The abundance and shape distribution of the MPs were closely related to the different types of human activities.

A review of atmospheric microplastics pollution: In-depth sighting of sources, analytical methods, physiognomies, transport and risks

Micro-sized plastics were first examined for atmospheric environment in 2016. From then on, they have been detected in both indoor and outdoor atmospheric samples, with indoor environments demonstrated as containing a big proportion of these particles. The sparse distribution of these particles, is attributed to their swift and long distance transportation that is mainly eased by their tiny size (1 μm to 5 mm) and low density. Due to ongoing limitation on detectable size, analysis methods together with a lack of standardized sampling and analytical procedures, few studies were conducted on airborne microplastics (MPs). Thus, the facts regarding the occurrence, global spatial distribution, fate, and threats to ecosystem and human health of airborne MPs, are still far from being fully clarified. This literature review is a broad depiction of a state of knowledge on atmospheric MPs. Within it, robust and concise information on the sources, inspection, transport, and threats pertaining to airborne MPs are presented. Particularly, the paper entails some information concerning traffic-generated MPs pollution, which has not been frequently discussed within previously published reports. In addition, this paper has widely unveiled sectors and aspects in need of further attention, with the gaps to be filled pinpointed.

Airborne microplastic concentrations and deposition across the Weser River catchment

Microplastic (MP) appears to be omnipresent in the atmosphere, raising concerns about dispersion across environmental compartments, ecological consequences and human health risks by inhalation. To date, data on the sources of atmospheric MP and deposition to river catchment areas are still sparse. We, therefore, took aerosol and total atmospheric deposition samples in the catchment area of the large German river Weser to estimate microplastic deposition fluxes (DFs) at six specific sites and airborne MP concentrations. Sampling in rural, suburban, and urban environments and wastewater treatment plants (WWTPs) was performed, aiming at a variation in airborne MP pollution and elucidating potential MP source areas. Aerosol samples were taken twice in April and October while monthly total deposition samples were collected over a period from March to October. Microplastics were detected in all analysed aerosol samples by Raman spectroscopy down to 4 μm, and in all 32 total deposition samples by μFT-IR down to 11 μm. Average MP number concentrations of 91 ± 47 m^-3 were found in aerosol samples. The measured total MP number DFs ranged between 10 and 367 N m^-2 day^-1 (99 ± 85 mean ± SD) corresponding to total deposition of 0.05 ± 0.1 kg ha^-1 per year and to an estimated 232 metric tons of plastic being deposited in the Weser River catchment annually. MP number DFs were higher in urban than rural sites. An effect of WWTPs on the MP abundance in air was not observed. Polypropylene, polyethylene, polyethylene terephthalate, polyvinyl chloride, polystyrene, and silicone fragments were found as the predominant polymer types in total deposition samples, while polyethylene particles dominated in aerosol samples. The results suggest that proximity to sources, especially to cities, increase the numbers of MP found in the atmosphere. It further indicates that atmospheric MP considerably contributes to the contamination of both aquatic and terrestrial habitats.

Road Dust in Urban and Industrial Environments: Sources, Pollutants, Impacts, and Management

Road dust (RD) is one of the most important sources of particles in the atmosphere, especially in industrial areas and cities. In this special issue, we collected 16 original articles that describe field, experimental, and modeling studies related to RD and its various size fractions as a key issue in understanding the relationships between several urban and industrial environments and in the identification of pollution sources. Articles in the special issue focus primarily on the following main topics: (1) study of the chemical composition and speciation of RD and its source attribution; (2) assessment of RD and aerosol pollution levels (including express technique), environmental hazards and public health risks; (3) distribution of stable and radioactive isotopes in RD; (4) determination of factors affecting the level of dust accumulation on roads and the intensity of its pollution; and (5) study of the effect of RD on the atmosphere and other environments. Based on the results presented in this special issue, but not limited to, some of the current challenges in studying RD are formulated, including the need for further geographically wider and analytically deeper work on various aspects of the formation, transport pathways, and accumulation of RD in urban, industrial and other areas.

Does size matter? Quantification of plastics associated with size fractionated biosolids

This study investigated the occurrence and contribution of plastic particles associated with size fractionated biosolids to the total concentration in biosolids (treated sewage sludge) samples collected from 20 wastewater treatment plants (WWTP) across Australia. This was achieved through sequential size fractionation of biosolids samples to quantify the mass concentration of 7 common plastics across a range of biosolids size fractions, including below 25 μm which has not been assessed in many previous studies. Quantitative analysis was performed by pressurized liquid extraction followed by pyrolysis coupled to gas chromatography - mass spectrometry. Of the total quantified plastics (Σ₇plastics), the greatest proportion (27%) of the total mass were identified in the nominal <25 μm sized biosolids fraction. Polyethylene dominated the polymer mass in every size fraction, even though profiles varied between WWTPs. When comparing the sum of all sites for each sized biosolids fraction, the plurality of the polyethylene, polyvinyl-chloride, polystyrene, polypropylene, polycarbonate, and polyethylene-terephthalate concentrations were associated with the smallest size fraction (<25 μm). We confirm for the first time the presence of plastic particles in biosolids below a size fraction that is not captured by many methods. This is important, because of the potential greater significance of plastics in the low sizes to environmental and human health.

Concentration of Microplastics in Road Dust as a Function of the Drying Period—A Case Study in G City, Korea

Microplastics (MPs) are plastic particles < 5 mm in diameter, which are detected in air, soil, and water, causing various environmental problems. In total, 37.3% of MPs are generated from point pollution sources and 62.7% from non-point sources; most of the non-point-source MPs are from vehicles tires, road-marking paint, and bitumen used in road pavements. In this study, the concentrations of MPs generated from roads in Goyang city, South Korea, were examined in terms of the drying period (0, 1, 2, or 3 d). Road dust sampling was performed at the kerb and quantitative and qualitative analyses were conducted for each sample. The MP concentrations were 552 (±39) MPs g−1 for a 0 d drying period and 1530 (±602) MPs g−1 for a 3 d drying period, confirming that the MP concentration in road dust increased with the increase in drying period. Among the detected substances, black particles accounted for the highest proportion (72%) and were found to be bitumen and tyre particles. This study also confirmed that the MPs accumulated on roads were washed away when rainfall exceeded a certain amount.

Microplastic occurrence in settled indoor dust in schools

This study examines for the first time the characteristics and human exposure of microplastics (MPs) in settled indoor dust in schools. An average of 195 MPs·g^-1 of dust were detected in settled indoor composite dust samples from 28 schools in Shiraz. White-transparent microfibres with lengths 500-1000 μm were the most abundant type of MP found among the samples examined. Polyethylene terephthalate and polypropylene MPs were dominant across all types of MP found including microfibres. MPs had generally smooth morphology with sharp or regular edges which could have been released to the environment as primary MPs. Among all sampling sites, higher concentrations of MPs were found in the south and centre of the city. These were areas affected by high population density, high traffic load and high presence of industrial units and workshops. Principal Component Analysis (PCA) showed a positive strong correlation between sampling sites and MP physical characteristics. The PCA plots revealed that MP sheets and fragments were prevalent in sites in the North of Shiraz, whereas microfibres were mainly associated with sites in the South. The levels of MPs in the South of Shiraz were greater than in the rest of the country and the wind direction and topography were found to be important factors affecting the MP distribution observed. Compared to other population groups, elementary school students had relatively high exposure risk to MPs. This study reveals that microfibres are widespread in Shiraz' schools and pose a high exposure risk to MPs for young students.

Weathering pathways and protocols for environmentally relevant microplastics and nanoplastics: What are we missing?

To date, most studies of microplastics have been carried out with pristine particles. However, most plastics in the environment will be aged to some extent; hence, understanding the effects of weathering and accurately mimicking weathering processes are crucial. By using microplastics that lack environmental relevance, we are unable to fully assess the risks associated with microplastic pollution in the environment. Emerging studies advocate for harmonization of experimental methods, however, the subject of reliable weathering protocols for realistic assessment has not been addressed. In this work, we critically analysed the current knowledge regarding protocols used for generating environmentally relevant microplastics and leachates for effects studies. We present the expected and overlooked weathering pathways that plastics will undergo throughout their lifecycle. International standard weathering protocols developed for polymers were critically analysed for their appropriateness for use in microplastics research. We show that most studies using weathered microplastics involve sorption experiments followed by toxicity assays. The most frequently reported weathered plastic types in the literature are polystyrene>polyethylene>polypropylene>polyvinyl chloride, which does not reflect the global plastic production and plastic types detected globally. Only ~10% of published effect studies have used aged microplastics and of these, only 12 use aged nanoplastics. This highlights the need to embrace the use of environmentally relevant microplastics and to pay critical attention to the appropriateness of the weathering methods adopted moving forward. We advocate for quality reporting of weathering protocols and characterisation for harmonization and reproducibility across different research efforts.

A novel method for the quantification of tire and polymer-modified bitumen particles in environmental samples by pyrolysis gas chromatography mass spectroscopy

Tire and road wear particles may constitute the largest source of microplastic particles into the environment. Quantification of these particles are associated with large uncertainties which are in part due to inadequate analytical methods. New methodology is presented in this work to improve the analysis of tire and road wear particles using pyrolysis gas chromatography mass spectrometry. Pyrolysis gas chromatography mass spectrometry of styrene butadiene styrene, a component of polymer-modified bitumen used on road asphalt, produces pyrolysis products identical to those of styrene butadiene rubber and butadiene rubber, which are used in tires. The proposed method uses multiple marker compounds to measure the combined mass of these rubbers in samples and includes an improved step of calculating the amount of tire and road based on the measured rubber content and site-specific traffic data. The method provides good recoveries of 83-92% for a simple matrix (tire) and 88-104% for a complex matrix (road sediment). The validated method was applied to urban snow, road-side soil and gully-pot sediment samples. Concentrations of tire particles in these samples ranged from 0.1 to 17.7 mg/mL (snow) to 0.6-68.3 mg/g (soil/sediment). The concentration of polymer-modified bitumen ranged from 0.03 to 0.42 mg/mL (snow) to 1.3-18.1 mg/g (soil/sediment).

Plastics in biosolids from 1950 to 2016: A function of global plastic production and consumption

Plastics are ubiquitous contaminants that leak into the environment from multiple pathways including the use of treated sewage sludge (biosolids). Seven common plastics (polymers) were quantified in the solid fraction of archived biosolids samples from Australia and the United Kingdom from between 1950 and 2016. Six plastics were detected, with increasing concentrations observed over time for each plastic. Biosolids plastic concentrations correlated with plastic production estimates, implying a potential link between plastics production, consumption and leakage into the environment. Prior to the 1990s, the leakage of plastics into biosolids was limited except for polystyrene. Increased leakage was observed from the 1990s onwards; potentially driven by increased consumption of polyethylene, polyethylene terephthalate and polyvinyl chloride. We show that looking back in time along specific plastic pollution pathways may help unravel the potential sources of plastics leakage into the environment and provide quantitative evidence to support the development of source control interventions or regulations.

The Critical Importance of Adopting Whole-of-Life Strategies for Polymers and Plastics

Plastics have been revolutionary in numerous sectors, and many of the positive attributes of modern life can be attributed to their use. However, plastics are often treated only as disposable commodities, which has led to the ever-increasing accumulation of plastic and plastic by-products in the environment as waste, and an unacceptable growth of microplastic and nanoplastic pollution. The catchphrase “plastics are everywhere”, perhaps once seen as extolling the virtues of plastics, is now seen by most as a potential or actual threat. Scientists are confronting this environmental crisis, both by developing recycling methods to deal with the legacy of plastic waste, and by highlighting the need to develop and implement effective whole-of-life strategies in the future use of plastic materials. The importance and topicality of this subject are evidenced by the dramatic increase in the use of terms such as “whole of life”, “life-cycle assessment”, “circular economy” and “sustainable polymers” in the scientific and broader literature. Effective solutions, however, are still to be forthcoming. In this review, we assess the potential for implementing whole-of-life strategies for plastics to achieve our vision of a circular economy. In this context, we consider the ways in which given plastics might be recycled into the same plastic for potential use in the same application, with minimal material loss, the lowest energy cost, and the least potential for polluting the environment.