Interfacial engineering of vacancy-rich nitrogen-doped FexOy@MoS2 Co-catalytic carbonaceous beads mediated non-radicals for fast catalytic oxidation

Enhanced activation of peroxymonosulfate by ZIF-67/g-C3N4 S-scheme photocatalyst under visible light assistance for degradation of polyethylene terephthalate

Photocatalyst-activated peroxymonosulfate (PMS) degradation of pollutants is already widely used for wastewater treatment under visible light. Polyethylene terephthalate (PET) is widely used in daily life, but waste plastics have an irreversible negative impact on the environment. In this paper, the ZIF-67/g-C3N4 S-scheme heterojunction catalyst was synthesized as a photocatalyst to achieve a good effect on PET degradation in coordination with PMS. The results indicated that PET could be degraded up to 60.63 ± 2.12 % under the combined effect of catalyst, PMS, and light. In this experiment, the influence of catalyst-to-plastic ratio, PMS concentration, aqueous pH, and inorganic anions on plastic degradation by the photocatalytic synergistic PMS system was discussed, and the excellent performance of this system for degrading PET was highlighted through a comparative test. Electron spin resonance (ESR) and free radical quenching experiments demonstrated that SO4•- contributes the largest amount to the PET degradation performance. Furthermore, results from gas chromatography and liquid chromatography-mass spectrometry (LC-MS) indicated that the plastic degradation products include CO, CH4, and organic small-molecule liquid fuels. Finally, a possible mechanism for the light/PMS system to degrade PET in water was suggested. This paper provides a feasible solution to treat waste microplastics in water.

Chitosan-derived N-doped carbon supported Cu/Fe co-doped MoS2 nanoparticles as peroxymonosulfate activator for efficient dyes degradation

Peroxymonosulfate (PMS), which is dominated by free radical (SO4•-) pathway, has a good removal effect on organic pollutants in complex water matrices. In this article, a new catalyst (CFM@NC) was synthesized by hydrothermal carbonization method with chitosan (CS) as N and C precursors, and used to activate PMS to degrade dye wastewater. CFM@NC/PMS system can degrade 50 mg·L-1 rhodamine B by 99.59 % within 30 min, and the degradation rate remains as high as 97.32 % after 5 cycles. It has good complex background matrices, acid-base anti-interference ability (pH 2.6-10.1), universality and reusability. It can degrade methyl orange and methylene blue by >98 % within 30 min. The high efficiency of the composite is due to the fact that CS-modified MoS2 as a carrier exposes a large number of active sites, which not only disperses CuFe2O4 nanoparticles and improves the stability of the catalyst, but also provides abundant electron rich groups, which promotes the activation of PMS and the production of reactive oxygen species (ROS). PMS is effectively activated by catalytic sites (Cu+/Cu2+, Fe2+/Fe3+, Mo4+/Mo6+, pyridine N, pyrrole N, edge sulfur and hydroxyl group) to produce a large number of radicals to attack RhB molecules, causing chromophore cleavage, ring opening, and mineralization. Among them, free radical SO4•- is the main ROS for RhB degradation. This work is expected to provide a new idea for the design and synthesis of environmentally friendly and efficient heterogeneous catalysts.

Methyl contributes to the directed phosphorus doping of g-C3N4: pH-dependent selective reactive oxygen species enable customized degradation of organic pollutants

In the photocatalytic degradation process, constructing a controllable composite oxidation system with radicals and nonradicals to meet the requirement for efficient and selective degradation of diverse pollutants is significant. Herein, a methylated and phosphorus-doped g-C3N4 (NPEA) can exhibit selective radical and nonradical species formation depending on the pH values. The NPEA can spontaneously switch the production of active species according to the pH value of the reaction system, exhibiting steady-state concentrations of ·O2- for 11.83 × 10-2 µmol L-1 s-1 (with 92.7 % selectivity) under alkaline conditions (pH = 11), and steady-state concentrations of 1O2 for 5.18 × 10-2 µmol L-1 s-1 (with 88.7 % selectivity) under acidic conditions (pH = 3). The NPEA exhibits stability and universality in the degradation of pollutants with rate constant for sulfamethazine (k = 0.261 min-1) and atrazine (k = 0.222 min-1). Moreover, the LC-MS and Fukui function demonstrated that the NPEA can tailor degradation pathways for pollutants, achieving selective degradation. This study offers a comprehensive insight into the mechanism of the photocatalytic oxidation system, elucidating the intricate interplay between pollutants and reactive oxygen species.

Chitosan derived N-doped carbon anchored Co3O4-doped MoS2 nanosheets as an efficient peroxymonosulfate activator for degradation of dyes

Peroxymonosulfate (PMS), which is dominated by non-free radical pathway, has a good removal effect on organic pollutants in complex water matrices. In this article, a biodegradable cobalt-based catalyst (Co3O4/MoS2@NCS) was synthesized by a simple hydrothermal method with chitosan (CS) as nitrogen‑carbon precursor and doped with Cobaltic‑cobaltous oxide (Co3O4) and Molybdenum disulfide (MoS2), and was used to activate PMS to degrade dye wastewater. Electrochemical tests showed that Co3O4/MoS2@NCS exhibited higher current density and cycling area than MoS2@NCS and MoS2. In the Co3O4/MoS2@NCS/PMS system, the degradation rate of 30 mg·L-1 rhodamine B (RhB) reached 97.75 % within 5 min, and kept as high as 94.34 % after 5 cycles. Its rate constant was 1.91 and 8.37 times that of MoS2@NCS/PMS and MoS2/PMS, respectively. It had good complex background matrices and acid-base anti-interference ability, and had good universality and reusability. The degradation rate of methyl orange (MO) and methylene blue (MB) were more than 91 % within 5 min at pH 4.8. The experimental results demonstrated that MoS2-modified CS as a carrier exposed a large number of active sites, which not only dispersed Co3O4 nanoparticles and improved the stability of the catalyst, but also provided abundant electron rich groups, and promoted the activation of PMS and the production of reactive oxygen species (ROS). PMS was effectively activated by catalytic sites (Co3+/Co2+, Mo4+/Mo5+/Mo6+, CO, pyridine N, pyrrole N, hydroxyl group and unsaturated sulfur), producing a large number of radicals that attack RhB molecules, causing chromophore cleavage, ring opening, and mineralization. Among them, non-free radical 1O2 was the main ROS for RhB degradation. This work is expected to provide a new idea for the design and synthesis of environmentally friendly and efficient MoS2-modified cobalt-based catalysts.

Density functional theory methods applied to homogeneous and heterogeneous catalysis: a short review and a practical user guide

The application of density functional theory (DFT) methods in catalysis has been growing fast in the last few decades thanks to both the availability of more powerful high computing resources and the development of new efficient approximations and approaches. DFT calculations allow for the understanding of crucial catalytic aspects that are difficult or even impossible to access by experiments, thus contributing to faster development of more efficient and selective catalysts. Depending on the catalytic system and properties under investigation, different approaches should be used. Moreover, the reliability of the obtained results deeply depends on the approximations involved in both the selected method and model. This review addresses chemists, physicists and materials scientists whose interest deals with the application of DFT-based computational tools in both homogeneous catalysis and heterogeneous catalysis. First, a brief introduction to DFT is presented. Then, the main approaches based on atomic centered basis sets and plane waves are discussed, underlining the main differences, advantages and limitations. Eventually, guidance towards the selection of the catalytic model is given, with a final focus on the evaluation of the energy barriers, which represents a crucial step in all catalytic processes. Overall, the review represents a rational and practical guide for both beginners and more experienced users involved in the wide field of catalysis.

Iron-Cobalt magnetic porous carbon beads activated peroxymonosulfate for enhanced degradation and Microbial inactivation

Magnetic carbon-based catalysts are promising materials for advanced oxidation processes, offering both high catalytic activity and environmental friendliness, and hold great potential in environmental remediation. In this work, Fe and Co zeolite imidazole frameworks (ZIFs) derived micron-sized magnetic porous carbon beads (MPCBs) were prepared by phase inversion and following the carbonization procedure, and the morphological and structural characteristics of the MPCBs were confirmed. The presence of pores and channels in the MPCBs provides a specific microenvironment for the for the catalysis of the core. Bisphenol A (BPA) was selected for the targeted pollutant, and the catalytic experiments confirmed that the effective catalytic activity of MPCBs in the presence of peroxymonosulfate (PMS), which could almost completely degrade BPA in 20 min with a reaction rate of 0.368 min-1. Furthermore, the MPCBs were used to effectively bacterial inactivation. Intermediate products of the BPA degradation process were validated and the toxicological studies showed a gradual decrease in toxicity, indicating effective reduction of potential hazards. The macroscopic preparation methods we developed for MPCBs that is promising for industrial applications and has the potential to cope with complex environmental remediation.

Deep mineralization of VOCs in an embedded hybrid structure CoFe2O4/MoS2/PMS wet scrubber system

Peroxymonosulfate (PMS)-based advanced oxidation processes in liquid phase systems can actively degrade toluene. In this work, the catechol structural surfactant was introduced to synthesize the dispersed and homogeneous CoFe2O4 nanospheres and embedded into MoS2 nanoflowers to form magnetically separable heterojunction catalysts. The innovative approach effectively mitigated the traditionally low reduction efficiency of transition metal ions during the heterogeneous activation process. In CoFe2O4/MoS2/PMS system, the toluene removal efficiency remained 95% within 2 h. The contribution of SO4⋅-, ·O2-, ·OH, and 1O2 was revealed by radical quenching experiment and electron paramagnetic resonance spectroscopy. The results illustrated that MoS2 offers ample reduction sites for facilitating PMS activation via Fe3+/Fe2+ redox interactions. Furthermore, an investigation into the toluene degradation pathway within the CoFe2O4/MoS2/PMS system revealed its capability to suppress the formation of toxic byproducts. This ambient-temperature liquid-phase method presented promising route for the removal of industrial volatile organic pollutants.

Structuring alginate/dopamine powder into macroscopic aerogel microsphere for exceptional removal of tetracycline from water: Performance and mechanisms

Aerogel was selected as one of IUPAC Top Ten Emerging Technologies in Chemistry in 2022, and has attracted tremendous concerns of scientists in removal of emerging contaminants. In this work a novel Fe³⁺ cross-linked alginate aerogel (SA/DA-Fe³⁺) with multiple sorption sites were facilely fabricated and applied for highly efficient removal of tetracycline (TC) from water. Results showed that Fe³⁺ and DA cooperatively improve adsorption of TC and TC was efficiently removed over a broad pH range of 4-8. The kinetics process can be better described by a chemisorption controlled pseudo-second-order kinetics model and Langmuir isotherm equation with characteristics of monolayer coverage. The fitted q_max value of TC at ambient temperature was 804.6 mg g^-1 higher than those of other reported adsorbents. Multiple interactions including π-π EDA, complexation, hydrogen bonding, electrostatic attraction, etc. were involved in adsorption process. Moreover, SA/DA-Fe³⁺ aerogel exhibited satisfactory stability, reusability, and recyclability for consecutive applications. Most importantly, after consecutively running for >1000 h with dynamic sorption capacity over 500 mg g^-1, the packed-column was still not saturated, manifesting its great potentials for treating actual wastewaters. Thus, above superiorities make SA/DA-Fe³⁺ a promising candidate adsorbent for treating TC-containing wastewater.

Applications of vacancy defect engineering in persulfate activation: Performance and internal mechanism

The vacancy defects in heterogeneous catalysts have received extensive attention for persulfate (PS) activation. Vacancy defects can tune the electronic structure of metal oxides and generate unsaturated coordination sites. Meanwhile, the adsorption energy of reactants on catalyst surface is optimized. Thereby, the reaction energy barrier between catalysts and PS decreases, which could promote catalytic activation and accelerate pollutants degradation. Nowadays, oxygen vacancy (OV), nitrogen vacancy (NV), sulfur vacancy (SV), selenium vacancy (SeV) and titanium vacancy (TiV) have been widely studied with great potential for water remediation. So far, no review was reported regarding the vacancy activated persulfate systems. This paper summarized the types, preparation, mechanism and applications of vacancy in PS systems systematically. In addition, we put forward possible development of vacancy engineering in PS activation systems. It is expected that this review will contribute to the controllable synthesis and applications of vacancies in catalysts for PS activation and contaminants removal.

Switching of radical and nonradical pathways through the surface defects of Fe3O4/MoOxSy in a Fenton-like reaction

Coexistence of radical and nonradical reaction pathways during advanced oxidation processes (AOPs) makes it challenging to obtain flexible regulation of high efficiency and selectivity for the requirement of diverse degradation. Herein, a series of Fe₃O₄/MoO_xS_y samples coupling peroxymonosulfate (PMS) systems enabled the switching of radical and nonradical pathways through the inclusion of defects and adjustment of Mo⁴⁺/Mo⁶⁺ ratios. The silicon cladding operation introduced defects by disrupting the original lattice of Fe₃O₄ and MoO_xS. Meanwhile, the abundance of defective electrons increased the amount of Mo⁴⁺ on the catalyst surface, promoting PMS decomposition with a maximum k value up to 1.530 min^-1 and a maximum free radical contribution of 81.33%. The Mo⁴⁺/Mo⁶⁺ ratio in the catalyst was similarly altered by different Fe contents, and Mo⁶⁺ contributed to the production of ¹O₂, allowing the whole system to attain a nonradical species-dominated (68.26%) pathway. The radical species-dominated system has a high chemical oxygen demand (COD) removal rate for actual wastewater treatment. Conversely, the nonradical species-dominated system can considerably improve the biodegradability of wastewater (biochemical oxygen demand (BOD)/COD = 0.997). The tunable hybrid reaction pathways will expand the targeted applications of AOPs.

A novel Fe/Mo co-catalyzed graphene-based nanocomposite to activate peroxymonosulfate for highly efficient degradation of organic pollutants

A novel 3D α-FeOOH@MoS₂/rGO nanocomposite was successfully fabricated by a simple in situ hydrothermal method. It is a highly efficient heterogeneous catalyst in activation of peroxymonosulfate (PMS) for rapid degradation of rhodamine B (RhB), with 99.9% of RhB removed within 20 min. The introduction of rGO contributes to uniform dispersion and sufficient contact of α-FeOOH and MoS₂ nanosheets. Highly active Mo(IV) enhances the reduction of Fe(III), improves Fe(III)/Fe(II) conversion and promotes the generation of O₂1, which ensures an improved catalytic activity. MoS₂/rGO hybrid can effectively solve the problem of material reunion and make α-FeOOH exhibit excellent catalytic performance. The α-FeOOH@MoS₂-rGO/PMS system is a co-catalytic system based on the active components of α-FeOOH and MoS₂. The main reactive oxygen species in the α-FeOOH@MoS₂-rGO/PMS system are O₂1, SO₄^.- and ⋅O₂^-, which contribute to a high reactivity over a wide range of pH (5-9). Besides, this system is highly resistant to anions (Cl^-, SO₄^2-) and natural organic matter (humic acid), and can be widely used for degradation of common organic pollutants. The α-FeOOH@MoS₂/rGO is a promising Fenton-like catalyst for refractory organic wastewater treatment.

Metal organic framework UiO-66 incorporated ultrafiltration membranes for simultaneous natural organic matter and heavy metal ions removal

In this work, a new type of UiO-66 incorporated polysulfone (PSf) ultrafiltration (UF) membranes was fabricated to enhance antifouling properties and heavy metal ions removal efficiency. The UF membranes incorporating different loadings of the UiO-66 filler were prepared via the classical phase inversion process. These membranes unveiled enhanced hydrophilicity, porosity, water uptake, zeta potential, mechanical strength, permeability, and HA removal ratios due to the incorporation of hydrophilic UiO-66 fillers. Particularly, HA rejection ratios were observed to be approximately 93% for all the modified membranes, which was attributed to electrostatic repulsion interactions between the hydrophilic groups of HA and UiO-66. Moreover, the antifouling abilities of the modified membranes were evaluated and found to be much better with a high flux recovery ratio (FRR) of about 88% when compared to the blank PSf membrane (only around 34%). Moreover, the UiO-66 incorporated membranes were highly-effective in the removal of contaminants like heavy metal ions (Sr²⁺, Pb²⁺, Cd²⁺, and Cr⁶⁺) and HA at the same time. Overall, the PSf UF membranes incorporating UiO-66 opened up a new avenue to enhance the membrane hydrophilicity, permeability, antifouling properties as well as heavy metal ions removal abilities.

Preparation and Characterization of the Forward Osmosis Membrane Modified by MXene Nano-Sheets

The Forward Osmosis (FO) membrane was the core of FO technology. Obtaining a high water flux while maintaining a low reverse solute flux has historically been considered the gold standard for a perfect FO membrane. In a thin-film composite FO membrane, the performance of the membrane was determined not only by the material and structure of the porous support layer but also by the structural and chemical properties of the active selective layer. Researchers have selected numerous sorts of materials for the FO membranes in recent years and have produced exceptional achievements. Herein, the performance of the modified FO membrane constructed by introducing new two-dimensional nanomaterial MXene nano-sheets to the interfacial polymerization process was investigated, and the performance of these modified membranes was investigated using a variety of characterization and testing methods. The results revealed that the MXene nano-sheets played an important role in improving the performance of the FO membrane. Because of the hydrophilic features of the MXene nano-sheets, the membrane structure may be tuned within a specific concentration range, and the performance of the modified FO membrane has been significantly enhanced accordingly. The optimal membrane water flux was boosted by around 80%, while its reverse solute flux was kept to a minimum of the resultant membranes. It showed that the addition of MXene nanosheets to the active selective layer could improve the performance of the FO membrane, and this method showed promising application prospects.

Iron pyrophosphate doped carbon nanocomposite for tetracycline degradation by activation of peroxymonosulfate

An Fe2P2O7@C catalyst was synthesized by simple carbonization of complex precursors and showed strong resistance to interference.

Sulfur vacancies on MoS2 enhanced the activation of peroxymonosulfate through the co-existence of radical and non-radical pathways to degrade organic pollutants in wastewater

The enhancement of vacancies in catalysts involving Fenton-like reactions is a promising way to remove organic pollutants in wastewater, but sulfur vacancies are rarely involved. In this work, MoS₂ containing defect sites were synthesized by a simple high-temperature treatment and then applied for activating peroxymonosulfate to eliminate organic pollutants in wastewater. The structure was characterized by several techniques such as XRD, BET, and XPS. Important influencing factors were systemically investigated. The results indicated that MoS₂ with sulfur vacancies possessed a higher catalytic activity than that of the parent MoS₂. The annealing temperature of the catalyst had a great effect on the removal of organic pollutants. Besides, the catalytic system had a wide pH range. Quenching and electron paramagnetic resonance (EPR) experiments indicated that the reaction system contained radical and non-radical species. The characterization results revealed that the defect sites in catalysts mainly strengthened the activity of catalysts. This study offers a new heterogeneous catalyst for the removal of organic pollutants via the peroxymonosulfate-based Fenton-like reactions.

Sulfur vacancies on MoS2 enhanced the activation of peroxymonosulfate to remove organic pollutants in wastewater.