Decontamination of toxic Malathion pesticide in aqueous solutions by Fenton-based processes: Degradation pathway, toxicity assessment and health risk assessment

Optimization, kinetics, and pathways of pharmaceutical pollutant degradation using solar Fenton technique

Solar Fenton is an important and extensively used advanced oxidation process (AOP) to degrade pharmaceutical pollutants. The objective of this study was to evaluate the performance of simultaneous degradation of the mixed pollutants (amoxicillin, acetaminophen, and ciprofloxacin) for an aqueous solution using the solar Fenton process. Operating parameters such as pH, iron doses, H2O2 doses, pollutant concentrations, and time were studied. From the experimental results, the ideal conditions were obtained for the removal of mixed pollutants such as pH 3, Fe2+ 0.04 mM, H2O2 4 mM, the concentration of the mixed pollutants 5 mg/L, solar radiation 400 W/m2, and time 10 min, respectively. The pseudo-first-order kinetics were utilized to investigate the degradation efficacy of the mixed pollutants. The result of the study indicates that the degradation efficiency was > 99% for the mixed pollutants. A maximum of 63% mineralization was observed, and hydroxyl radical scavenger effects were studied. The best optimal conditions were applied to assess the spiked wastewater (municipal wastewater (MWW) and hospital wastewater (HWW)). The highest elimination rates for AMX, ACET, and CIP were observed as 65%, 89%, and 85% for MWW and 76%, 92%, and 80% for HWW, respectively. The degraded by-products were detected by LC-ESI-MS in the water matrix (aqueous solution and spiked wastewater), and ECOSAR analysis was performed for the transformed products. The study concluded that the solar Fenton technique is promising and effective for the removal of mixed pollutants from the water matrix.

Ecotoxicological strategies employing biochemical markers and organisms to monitor the efficacy of malathion photolysis treatment

The objective of this study was to assess the photolysis-mediated degradation of malathion in standard and commercial formulations, and to determine the toxicity of these degraded formulations. Degradation tests were carried out with 500 μg L-1 of malathion and repeated three times. The initial and residual toxicity was assessed by using Lactuca sativa seeds for phytotoxicity, Stegomyia aegypti larvae for acute toxicity, and Stegomyia aegypti mosquitoes (cultivated from the larval stage until emergence as mosquitoes) to evaluate the biochemical markers of sublethal concentrations. For the standard formulations the photolytic process efficiently reduced the initial concentration of malathion to levels below the regulatory limits however, the formation of byproducts was revealed by chromatography, which allowed for a more complete proposal of photolytic-mediated malathion degradation route. The degraded formulations inhibited the growth of L. sativa seeds, while only the untreated formulations showed larvicidal activity and mortality. Both formulations slightly inhibited acetylcholinesterase activity in S. aegypti mosquitoes, while the standard formulation decreased and the commercial formulation increased glutathione S-transferase activity. However, there were no significant differences for superoxide dismutase, esterase-α, esterase-β and lipid peroxidation. These findings indicate that in the absence of the target compound, the presence of byproducts can alter the enzymatic activity. In general, photolysis effectively degrade malathion lower than the legislation values; however, longer treatment times must be evaluated for the commercial formulation.

Mechanisms of oxidative response during biodegradation of malathion by S. oneidensis MR-1

Malathion, an extensively used organophosphorus pesticide, poses a high potential risk of toxicity to humans and the environment. Shewanella (S.) oneidensis MR-1 has been proposed as a strain with excellent bioremediation capabilities, capable of efficiently removing a wide range of hard-to-degrade pollutants. However, the physiological and biochemical response of S. oneidensis MR-1 to malathion is unknown. Therefore, this study aimed to examine how S. oneidensis MR-1 responds physiologically and biochemically to malathion while also investigating the biodegradation properties of the pesticide. The results showed that the 7-day degradation rates of S. oneidensis MR-1 were 84.1, 91.6, and 94.0% at malathion concentrations of 10, 20, and 30 mg/L, respectively. As the concentration of malathion increased, superoxide dismutase and catalase activities were inhibited, leading to a significant rise in malondialdehyde content. This outcome can be attributed to the excessive production of reactive oxygen species (ROS) triggered by malathion stress. In addition, ROS production stimulates the secretion of soluble polysaccharides, which alleviates oxidative stress caused by malathion. Malathion-induced oxidative damage further exacerbated the changes in the cellular properties of S. oneidensis MR-1. During the initial stages of degradation, the cell density and total intracellular protein increased significantly with increasing malathion exposure. This can be attributed to the remarkable resistance of S. oneidensis MR-1 to malathion. Based on scanning electron microscopy observations, continuous exposure to contaminants led to a reduction in biomass and protein content, resulting in reduced cell activity and ultimately leading to cell rupture. In addition, this was accompanied by a decrease in Na+/K+- ATPase and Ca2+/Mg2+-ATPase levels, suggesting that malathion-mediated oxidative stress interfered with energy metabolism in S. oneidensis MR-1. The findings of this study provide new insights into the environmental risks associated with organophosphorus pesticides, specifically malathion, and their potential for bioremediation.

Utilization of the copper recovered from waste printed circuit boards as a metal precursor for the synthesis of TiO2/magnetic-MOF(Cu) nanocomposite: Application in photocatalytic degradation of pesticides in aquatic solutions

In this study, a number of leaching solutions (H2SO4, CuSO4 and NaCl) and an electrochemical method were used together for the separation of Cu from waste printed circuit boards. Secondly, the magnetic-MOF(Cu) was synthesized using the Cu recovered from waste printed circuit boards. Thereafter, TiO2/mag-MOF(Cu) composite was prepared and its photocatalytic activity was assessed in the photo degradation of two prominent organophosphorus pesticides, namely malathion (MTN) and diazinon (DZN). The catalytic structure of the MOF-based composite was fully characterized by various analyses such as XRD, SEM, EDAX, FT-IR, VSM and UV-vis. The obtained analyses confirmed the successful synthesis of TiO2/mag-MOF(Cu) composite. The synthesized composite exhibited highly efficient in the degradation of both pollutants under the following conditions: pH 7, contaminant concentration 1 mg/L, the catalyst dosage of 0.4 g/L, visible light intensity 75 mW/cm2 and reaction time of 45 min. First order kinetic model was best suited with the experimental results (R2: 0.97-0.99 for different MTN and DZN concentrations). Trapping studies revealed that superoxide radicals (O2•-) played an important role during the degradation process. Furthermore, the catalyst demonstrated a superb recovery as well as high stability over five cyclic runs of reuse. In addition, the total organic carbon (TOC) analysis showed over 83% and 85% mineralization for MTN and DZN, respectively. The combined system of TiO2/mag-MOF(Cu)/Vis also exhibited a great level of efficiency and feasibility in the treatment of tap water and treated wastewater samples. It is concluded that TiO2/mag-MOF(Cu) could be used as an excellent catalyst for the photodegradation of MTN and DZN in aqueous solution.

Cu2O/Fe3O4/UiO-66 nanocomposite as an efficient fenton-like catalyst: Performance in organic pollutant degradation and influencing factors based machinelearning

The persistent presence of organic pollutants like dyes in water environment necessitates innovative approaches for efficient degradation. In this research, we developed an advanced hybrid catalyst by combining metal oxides (Cu2O, Fe3O4) with UiO-66, serving as a heterogeneous Fenton catalyst for for efficient RB19 breakdown in water with H2O2. The control factors to the catalytic behavior were also quantified by machine learning. Experimental results show that the catalytic performance was much better than its individual components (P < 0.05 & non-zero 95% C.I). The improved catalytic efficiency was linked to the occurrence of active metal centers (Fe, Cu, and Zr), with Cu(I) from Cu2O playing a crucial role in promoting increased production of HO•. Also, UiO-66 served as a catalyst support, attracting pollutants to the reaction center, while magnetic Fe3O4 aids catalyst recovery. The optimal experimental parameters for best performance were pH at 7, catalyst loading of 1.6 g/L, H2O2 strength of 0.16 M, and reaction temperature of 25 °C. The catalyst can be magnetically separated and regenerated after five recycling times without significantly reducing catalytic activity. The reaction time and pH were ranked as the most influencing factors on catalytic efficiency via Random Forest and SHapley Additive exPlanations models. The findings show that developed catalyst is a suitable candidate to remove dyes in water by Fenton heterogeneous reaction.

Modeling of adsorptive removal of azithromycin from aquatic media by CoFe2O4/NiO anchored microalgae-derived nitrogen-doped porous activated carbon adsorbent and colorimetric quantifying of azithromycin in pharmaceutical products

Herein, it was aimed to optimize the removal process of Azithromycin (Azi) from the aquatic environment via CoFe2O4/NiO nanoparticles anchored onto the microalgae-derived nitrogen-doped porous activated carbon (N-PAC), besides developing a colorimetric method for the swift monitoring of Azi in pharmaceutical products. In this study, the Spirulina platensis (Sp) was used as a biomass resource for fabricating CoFe2O4/NiO@N-PAC adsorbent. The pores of N-PAC mainly entail mesoporous structures with a mean pore diameter of 21.546 nm and total cavity volume (Vtotal) of 0.033578 cm3. g-1. The adsorption studies offered that 98.5% of Azi in aqueous media could remove by CoFe2O4/NiO@N-PAC. For the cyclic stability analysis, the adsorbent was separated magnetically and assessed at the end of five adsorption-desorption cycles with a negligible decrease in adsorption. The kinetic modeling revealed that the adsorption of Azi onto the CoFe2O4/NiO@N-PAC was well-fitted to the second-order reaction kinetics, and the highest adsorption capacity was found as 2000 mg. g-1 at 25 °C based on the Langmuir adsorption isotherm model at 0.8 g. L-1 adsorbent concentration. The Freundlich isotherm model had the best agreement with the experimental data. Thermodynamic modeling indicated the spontaneous and exothermic nature of the adsorption process. Moreover, the effects of pH, temperature, and operating time were also optimized in the colorimetric Azi detection. The blue ion-pair complexes between Azi and Coomassie Brilliant Blue G-250 (CBBG-250) reagent followed Beer's law at wavelengths of 640 nm in the concentration range of 1.0 μM to 1.0 mM with a 0.94 μM limit of detection (LOD). In addition, the selectivity of Azi determination was verified in presence of various species. Furthermore, the applicability of CBBG-250 dye for quantifying Azi was evaluated in Azi capsules as real samples, which revealed the acceptable recovery percentage (98.72-101.27%). This work paves the way for engineering advanced nanomaterials for the removal and monitoring of Azi and assures the sustainability of environmental protection and public health.

Determination of the use of Ligula intestinalis as a bioindicator in malathion residues

In this study, the usability of Ligula intestinalis as a bioindicator for pesticide accumulation was investigated. Two different experiments were designed for the detection of pesticide residues and its withdrawal period. In the first experiment, the accumulation of malathion for 10 days was measured in the hybrid fish, Squalius orientalisxAlburnus derjugini sampled from a dam lake. In the next experiment, withdrawal was measured for 15 days. The infected and healthy fish in groups exposed malathion and not exposed malathion were sampled at the end of the first experiment. No malathion residue was found in the control group that was not exposed with malathion. For the second experiment, infected and healthy fish from malathion and without malathion groups were sampled to measure the elimination of malathion on the 1st, 4th, 5th, 8th, 12th, and 15th days. At the end of the first experiment, the presence of malathion was not detected in the control group while accumulation was observed in both fish and L. intestinalis in the experimental group. At the end of the second experiment (15th day), the highest residual value was found in L. intestinalis (1.02 mg/kg) while it was determined as 0.009 mg/kg in infected fish and 0.006 mg/kg in uninfected fish. According to the correlation, malathion accumulation was linear between uninfected fish and infected fish. On the other hand, an inverse correlation was found between L. intestinalis and both malathion and control fish. As a result, it was determined that L. intestinalis can be used as a bioindicator in pesticide accumulation and the pesticide is still detectable in the parasite after withdrawal from fish.

Efficient purification of aqueous solutions contaminated with sulfadiazine by coupling electro-Fenton/ultrasound process: optimization, DFT calculation, and innovative study of human health risk assessment

In the current work, the hybrid process potential of ultrasound (US) and electro-Fenton (EF), named sono-electro-Fenton (SEF), was fully investigated for sulfadiazine (SDZ) degradation. The decontamination in the integration approach was revealed to be greater than in individual procedures, i.e., EF process (roughly 66%) and US process (roughly 15%). The key operating process factors (i.e., applied voltage, H2O2 content, pH, initial concentration of SDZ, and reaction time) affecting SDZ removal were evaluated and optimized using Box-Behnken Design (BBD). In addition, an adaptive neuro-fuzzy inference system (ANFIS) as an efficient predictive model was applied to forecast the decontamination efficiency of SDZ through the SEF process based on the same findings produced from BBD. The results revealed that the predictability of SDZ elimination by the ANFIS and BBD approaches exhibited an excellent agreement (a greater R2 of 0.99%) among the both models. Density functional theory was also employed to forecast the plausible decomposition elucidation by the bond-breaking mechanism of organic substances. Plus, the main side products of SDZ degradation during the SEF process were tracked. Eventually, the non-carcinogenic risk assessment of different samples of natural water containing SDZ that was treated by adopting US, EF, and SEF processes was examined for the first time. The findings indicated that the non-carcinogenic risk (HQ) values of all the purified water sources were computed in the permissible range.

The overlooked role of UV185 induced high-energy excited states in the dephosphorization of organophosphorus pesticide by VUV/persulfate

Vacuum ultraviolet (VUV) based advanced oxidation processes (AOPs) recently attracted widespread interests. However, the role of UV₁₈₅ in VUV is only considered to be generating a series of active species, while the effect of photoexcitation has long been overlooked. In this work, the role of UV₁₈₅ induced high-energy excited state for the dephosphorization of organophosphorus pesticides was studied using malathion as a model. Results showed malathion degradation was highly related to radical yield, while its dephosphorization was not. It was UV₁₈₅ rather than UV₂₅₄ or radical yield that was responsible for malathion dephosphorization by VUV/persulfate. DFT calculation results demonstrated that the polarity of P-S bond was further increased during UV₁₈₅ excitation, favoring dephosphorization while UV₂₅₄ did not. The conclusion was further supported by degradation path identification. Moreover, despite the fact that anions (Cl^-, SO₄^2- and NO₃^-) considerably affected radical yield, only Cl^- and NO₃^- with high molar extinction coefficient at 185 nm significantly affected dephosphorization. This study shed light on the crucial role of excited states in VUV based AOPs and provided a new idea for the development of mineralization technology of organophosphorus pesticides.

Potential protective effects of red grape seed extract in a rat model of malathion-induced neurotoxicity

Background and Aim: Exposure to pesticide mixtures used in agricultural practice poses a grave risk to non-target animals. This study aimed to determine whether red grape seed extract (RGSE, which is 95% bioflavonoids and equal to 12,000 mg of fresh red grape seed, and 150 mg of vitamin C) alleviated the changes in brain-derived neurotrophic factor (BDNF) level, acetylcholinesterase activity, oxidative stress, and apoptosis induced by orally administered malathion in a rat model of malathion-induced neurotoxicity. Materials and Methods: Thirty-two adult male Wistar albino rats were divided into four groups and exposed to malathion with or without 4 weeks of RGSE treatment, treated with RGSE alone, or left untreated as controls. The animals were euthanized 24 h after last treatment. Brain samples were collected to measure acetylcholinesterase, superoxide dismutase (SOD), and caspase 3 activity, total antioxidant capacity (TAC), and BDNF levels. Results: Malathion significantly reduced acetylcholinesterase and SOD activity and TAC and significantly increased caspase 3 activity. In comparison, acetylcholinesterase and SOC activity, BDNF level, and TAC were improved and caspase 3 activity was decreased in the malathion-RGSE group, indicating that RGSE corrected the alterations detected in these biochemical parameters. Conclusion: Oxidative stress and apoptosis in the brains of rats exposed to oral malathion were substantially controlled by RGSE treatment.

Bio-inspired aptamers decorated gold nanoparticles enable visualized detection of malathion

Biosensors always respond to the targets of interest in a specific manner, employing biological or bio-mimic recognition elements such as antibodies and aptamers. Inspired by target recognition in nature, an aptamer-mediated, gold nanoparticle-based sensing approach is developed in this work for effective determination of malathion. The sensing system consists of negatively charged aptamer probes, and polycationic proteins, protamine, as well as exceptional colorimetric nanoprobes, barely gold nanoparticles (AuNPs). Protamine molecules bound to aptamer probes hinder the aggregation of AuNPs, while no such inhibition is maintained when aptamer-specific malathion is introduced into the solution, thus leading to the solution colour change from red to blue observable by the naked eye. The assay is accomplished via a mix-and-measure step within 40 min with a detection limit as low as 1.48 μg/L (3σ/s rule). The assay method also exhibits high selectivity and good applicability for the quantification of malathion in tap water with recovery rates of 98.9%-109.4%. Additionally, the good detection accuracy is also confirmed by the high-performance liquid chromatography method. Therefore, the non-enzymatic, label- and device-free characteristics make it a robust tool for malathion assay in agricultural, environmental, and medical fields.

Statistical modeling optimization for antibiotics decomposition by ultrasound/electro-Fenton integrated process: Non-carcinogenic risk assessment of drinking water

The present work proposes an ultrasound (US) assisted electro-Fenton (EF) process for eliminating penicillin G (PNG) and ciprofloxacin (CIP) from aqueous solutions and the process was further optimized by response surface methodology (RSM)- Box-Behnken design (BBD). The impact of pH, hydrogen peroxide (H₂O₂) concentration, applied voltage, initial pollutant concentration, and operating time were studied. The capability application of the electro-Fenton (EF) and US processes was compared separately and in combination under the optimum conditions of pH of 4, a voltage of 15 V, the initial antibiotic concentration of 20.7 mg/L, H₂O₂ concentration of 0.8 mg/L, and the operating time of 75 min. The removal efficiency of PNG and CIP using the sono-electro-Fenton (SEF) process, as the results revealed, was approximately 96% and 98%, respectively. The experiments on two scavengers demonstrated that ^⦁OH contributes significantly to the CIP and PNG degradation by SEF, whereas ^⦁O^-₂ corresponds to only a negligible amount. The total organic carbon (TOC) and chemical oxygen demand (COD) analyses were used to assess the mineralization of CIP and PNG. The efficiency of COD and TOC removal was reached at 73.25% and 62.5% for CIP under optimized operating circumstances, and at 61.52% and 72% for PNG, respectively. These findings indicate that a sufficient rate of mineralization was obtained by SEF treatment for the mentioned pollutants. The reaction kinetics of CIP and PNG degradation by the SEF process were found to follow a pseudo-first-order kinetic model. In addition, the human health risk assessment of natural water containing CIP and PNG that was purified by US, EF, and SEF processes was done for the first time. According to the findings, the non-carcinogenic risk (HQ) caused by drinking purified water by all three systems was calculated in the acceptable range. Thus, SEF is a proper system to remove various antibiotics in potable water and reduces their human health risks.

Fabrication and characterization of pectin-graphene oxide-magnesium ferrite-zinc oxide nanocomposite for photocatalytic degradation of diclofenac in an aqueous solution under visible light irradiation

Wastewater containing pharmaceutical contaminants has become a critical environmental concern due to rising population and drug consumption caused by increased life expectancy. Diclofenac (DCF) is one of the most applicable drugs for veterinary and human health purposes, polluting surface waters in different ways. This work aims to synthesize a novel pectin-graphene oxide (GO)-magnesium ferrite (MgFe₂O₄)-zinc oxide (ZnO) nanocomposite (PGMZ) for photocatalytic degradation of DCF in an aquatic environment under visible light irradiation. The single and synthesized nanocomposites were characterized by several analyses, confirming the successful synthesis of the nanocomposite. Effects of four operation conditions, including nanocomposite dosage (1-1.25 g/L), nanocomposite type, initial contaminant concentration (35-55 mg/L), and solution pH (3-11), were investigated on the degradation performance. From the kinetic study, the effect of mixing two composites, i.e., synergy percentage, was 38.7% when ZnO-MgFe₂O₄ particles were added to the GO-pectin structure. By examining the effect of different free radical enhancers and scavenging compounds on the DCF photodegradation, the most influential scavenging components were in the following order; NaCl > Na₂CO₃ > Na₂SO₄, while K₂S₂O₈ was a better enhancer than H₂O₂ at their optimal concentration. Finally, the PGMZ photocatalyst was reused six times with a reduction of about 20% in its removal efficiency, indicating excellent reusability and stability.

Photocatalytic activity of graphene oxide-TiO2 nanocomposite on dichlorvos and malathion and assessment of toxicity changes due to photodegradation

Heterogeneous photocatalysis was used for the removal of two widely used organophosphorus pesticides, dichlorvos, and malathion from water. Graphene oxide-TiO₂ nanocomposite (GOT) was synthesized and used as a photocatalyst for the removal of these pesticides. Batch studies for optimizing photocatalytic degradation and mineralization of pesticides over 80 min were conducted by varying the pH (2-10), catalyst dose (20 mg/L-200 mg/L), and initial pesticide concentration (0.5 mg/L-20 mg/L), and the irradiation source (125 W UV and visible lamp). Degradation kinetics for the pesticides were evaluated. Ellman assay was used to estimate the toxic effect of pesticides and evaluate toxicity reduction due to treatment. The highest degradation and mineralization of dichlorvos and malathion was observed at pH 6 and the optimum catalyst dose was 60 mg/L. Under UV irradiation, 80% and 90% degradation were observed for dichlorvos and malathion, respectively for 0.5 mg/L initial pesticide concentration. The photocatalytic degradation reaction followed Langmuir-Hinshelwood kinetics. A high degree of mineralization was achieved for both the pesticides. Analysis of the results revealed that the residual toxic effect after photocatalysis was primarily due to the residual parent compound. A comparative study revealed that GOT yielded better pesticide degradation compared to commercially available TiO₂ under both UV and visible irradiation.

A review of radical and non-radical degradation of amoxicillin by using different oxidation process systems

Pharmaceutical compounds have piqued the interest of researchers due to an increase in their demand, which increases the possibility of leakage into the environment. Amoxicillin (AMX) is a penicillin derivative used for the treatment of infections caused by gram-positive bacteria. AMX has a low metabolic rate in the human body, and around 80-90% is unmetabolized. As a result, AMX residuals should be treated immediately to avoid further accumulation in the environment. Advanced oxidation process techniques are an efficient way to degrade AMX. This review attempts to collect, organize, summarize, and analyze the most up to date research linked to the degradation of AMX by different advanced oxidation process systems including photocatalytic, ultrasonic, electro-oxidation, and advanced oxidation process-based on partials. The main topics investigated in this review are degradation mechanism, degradation efficiency, catalyst stability, the formation of AMX by-products and its toxicity, in addition, the influence of different experimental conditions was discussed such as pH, temperature, scavengers, the concentration of amoxicillin, oxidants, catalyst, and doping ratio. The degradation of AMX could be inhibited by very high values of pH, temperature, AMX concentration, oxidants concentration, catalyst concentration, and doping ratio. Several AMX by-products were discovered after oxidation treatment, and several of them had lower or same values of LC₅₀ (96 h) fathead minnow of AMX itself, such as m/z 384, 375, 349, 323, 324, 321, 318, with prediction values of 0.70, 1.10, 1.10 0.42, 0.42, 0.42, and 0.42 mg/L, respectively. We revealed that there is no silver bullet system to oxidize AMX from an aqueous medium. However, it is recommended to apply hybrid systems such as Photo-electro, Photo-Fenton, Electro-Fenton, etc. Hybrid systems are capable to cover the drawbacks of the single system. This review may provide important information, as well as future recommendations, for future researchers interested in treating AMX using various AOP systems, allowing them to improve the applicability of their systems and successfully oxidize AMX from an aqueous medium.

Potential protective effects of Thyme (Thymus vulgaris) essential oil on growth, hematology, immune responses, and antioxidant status of Oncorhynchus mykiss exposed to Malathion

As an abundant source of antioxidants and diet flavor enhancers, the plant essential oils can have positive effects on fish growth, and resistance against environmental stressors. In this study, garden thyme (Thymus vulgaris) essential oil (TEO) was used in the diet of rainbow trout, Oncorhynchus mykiss, to evaluate its protective effect against Malathion pesticide exposure. Tested fish (19.99 ± 0.01 g) were divided into six groups (three replicates), namely: T1: control diet; T2: control diet + 0.025 mg L−1 malathion; T3: control diet + 0.075 mg L−1 malathion; T4: control diet + 1% TEO; T5: control diet + 0.025 mg L−1 malathion + 1% TEO and T6: control diet + 0.075 mg L−1 malathion + 1% TEO. After 21 days, T4 fish had the highest final body weight (FW), weight gain (WG), specific growth rate (SGR), and the lowest feed conversion ratio (FCR) among experimental treatments (P<0.05). The blood parameters including the red blood cells (RBC), white blood cell count (WBC), hematocrit (Hct), and hemoglobin (Hb) values were the highest in T4 treatment, displaying a significant difference with T1 treatment (P<0.05). Fish in the T4 groups had the highest total protein (TP) and albumin (ALB), while fish of T3 showed the lowest levels of these parameters (P<0.05) and also had the highest level of triglycerides (TRG), cholesterol (CHOL), lactate dehydrogenase (LDH), and urea (Ur). Alanine aminotransferase (ALT), aspartate aminotransferase (AST), and alkaline phosphatase (ALP) enzymes recorded the lowest levels in T4 treatment, which showed a significant difference with T1 group. The catalase (CAT) and superoxide dismutase (SOD) showed the highest activities in T4 treatment, while the lowest SOD and the highest malondialdehyde (MDA) levels occurred in T3 group (P<0.05). Total immunoglobulin (total Ig) level, alternative complement (ACH50) and lysozyme in the serum and skin mucus of T4 treatment of rainbow trout showed the highest activities with a significant difference from groups (P<0.05). From the results of the present study, it can be concluded that 1% of T. vulgaris as a supplement to the diet of rainbow trout can stimulate and improve the immune system of the fish. TEO can have a protective effect against unfavorable effects of malathion and improves the growth of the fish.

Efficient ofloxacin degradation via photo-Fenton process over eco-friendly MIL-88A(Fe): Performance, degradation pathways, intermediate library establishment and toxicity evaluation

The high-throughput production of the eco-friendly MIL-88A(Fe) was achieved under mild reaction conditions with normal pressure and temperature. The as-prepared MIL-88A(Fe) exhibited efficient photo-Fenton catalytic ofloxacin (OFL) degradation upon visible light irradiation with good stability and reusability. The OFL (20.0 mg/L) was completely degraded within 50 min under visible light with the aid of MIL-88A(Fe) (0.25 g/L) and H₂O₂ (1.0 mL/L) in aqueous solution (pH = 7.0). The hydroxyl radicals (·OH) are the main active species during the photo-Fenton oxidation process. Meanwhile, the degradation intermediates and the corresponding degradation pathways were identified and proposed with the aid of both ultra-high performance liquid chromatography tandem quadrupole time-of-flight mass spectrometry (UHPLC-Q-TOF-MS) and density functional theory (DFT) calculations. Finally, the degradation product library was firstly established to identify intermediate transformation products (TPs) with their variation of concentration, and their corresponding toxicologic activities were assessed via Toxtree and T.E.S.T software as well. Finally, the MIL-88A is efficient and stable with four cycles' catalysis operations, demonstrating good potential for water treatment.

A review on magnetic sensors for monitoring of hazardous pollutants in water resources

Water resources have long been of interest to humans and have become a serious issue in all aspects of human life. The disposal of hazardous pollutants in water resources is one of the biggest global concerns and poses many risks to human health and aquatic life. Therefore, the control of hazardous pollutants in water resources plays an important role, when it comes to evaluating water quality. Due to low toxicity, good electrical conductivity, facile functionalization, and easy preparation, magnetic materials have become a good alternative in recent years to control hazardous pollutants in water resources. In the present study, the idea of using magnetic sensors in controlling and monitoring of pharmaceuticals, pesticides, heavy metals, and organic pollutants have been reviewed. The water pollutants in drinking water, groundwater, surface water, and seawater have been discussed. The toxicology of water hazardous pollutants has also been reviewed. Then, the magnetic materials were discussed as sensors for controlling and monitoring pollutants. Finally, future remarks and perspectives on magnetic nanosensors for controlling hazardous pollutants in water resources and environmental applications were explained.

Electrochemical sensing system for the analysis of emerging contaminants in aquatic environment: A review

This survey distinguishes understudied spaces of arising impurity research in wastewaters and the habitat, and suggests bearing for future checking. Thinking about the impeding effect of toxins on human wellbeing and biological system, their discovery in various media including water is fundamental. This review sums up and assesses the latest advances in the electrochemical detecting of emerging contaminants (ECs). This survey is expected to add to the advancement in electrochemical applications towards the ECs. Different electrochemical insightful procedures like Amperometry, Voltammetry has been examined in this overview. The improvement of cutting edge nanomaterial-based electrochemical sensors and biosensors for the discovery of drug compounds has accumulated monstrous consideration because of their benefits, like high affectability and selectivity, continuous observing, and convenience has been reviewed in this survey. This survey likewise features the diverse electrochemical treatment procedures accessible for the removal of ECs.

MXene-based electrochemical sensors for detection of environmental pollutants: A comprehensive review

Since the discovery of MXenes at Drexel University in the United States in 2011, there has been extensive research regarding various applications of MXenes including environmental remediation. MXenes with a general formula of M_n+1X_nT_x are a class of two-dimensional (2D) transition metal carbides, carbonitrides, and nitrides with unique chemical and physical characteristics as nanomaterials. MXenes feature characteristics such as high conductivity, hydrophobicity, and large specific surface areas that are attracting attention from researchers in many fields including environmental water engineering such as desalination and wastewater treatment as well as designing and building efficient sensors to detect hazardous pollutants in water. In this study, we review recent developments in MXene-based nanocomposites for electrochemical (bio) sensing with a particular focus on the detection of hazardous pollutants, such as organic components, pesticides, nitrite, and heavy metals. Integration of these 2D materials in electrochemical enzyme-based and affinity-based biosensors for environmental pollutants is also discussed. In addition, a summary of the key challenges and future remarks are presented. Although this field is relatively new, future research on biosensors of MXene-based nanocomposites need to exploit the remarkable properties of these 2D materials.

Congo red dye removal from aqueous environment by cationic surfactant modified-biomass derived carbon: Equilibrium, kinetic, and thermodynamic modeling, and forecasting via artificial neural network approach

Herein, it was aimed to optimize, model, and forecast the biosorption of Congo Red onto biomass-derived biosorbent. Therefore, the waste-orange-peels were processed to fabricate biomass-derived carbon, which was activated by ZnCl₂ and modified with cetyltrimethylammonium bromide. The physicochemical properties of the biosorbents were explored by scanning electron microscopy and N₂ adsorption/desorption isotherms. The effects of pH, initial dye concentration, temperature, and contact duration on the biosorption capacity were investigated and optimized by batch experimental process, followed by the kinetics, equilibrium, and thermodynamics of biosorption were modeled. Furthermore, various artificial neural network (ANN) architectures were applied to experimental data to optimize the ANN model. The kinetic modeling of the biosorption offered that biosorption was in accordance both with the pseudo-second-order and saturation-type kinetic model, and the monolayer biosorption capacity was calculated as 666.67 mg g^-1 at 25 °C according to Langmuir isotherm model. According to equilibrium modeling, the Freundlich isotherm model was better fitted to the experimental data than the Langmuir isotherm model. Moreover, the thermodynamic modeling revealed biosorption took place spontaneously as an exothermic process. The findings revealed that the best ANN architecture trained with trainlm as the backpropagation algorithm, with tansig-purelin transfer functions, and 14 neurons in the single hidden layer with the highest coefficient of determination (R² = 0.9996) and the lowest mean-squared-error (MSE = 0.0002). The well-agreement between the experimental and ANN-forecasted data demonstrated that the optimized ANN model can predict the behavior of the anionic dye biosorption onto biomass-derived modified carbon materials under various operation conditions.

Photocatalytic degradation of cefixime in aqueous solutions using functionalized SWCNT/ZnO/Fe3O4 under UV-A irradiation

In this study, SWCNT/ZnO/Fe₃O₄ heterojunction composite was prepared for enhancing the degradation of β-lactam drugs such as cefixime (CFX) from an aqueous solution. The effects of several factors such as pH, initial concentration of CFX, and photocatalyst dose were investigated. Among them, pH was the most effective parameter for the degradation of CFX. Pareto graph revealed that the degradation process was accelerated at acidic conditions. The surface morphology test such as scanning electron microscopy (SEM) was applied to enlighten the surface of the functionalized SWCNT/ZnO/Fe₃O₄ photocatalyst. Highly advanced analyzes such as X-ray Photoelectron Spectroscopy (XPS), Energy Dispersive Spectrometry (EDX), Fourier-Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), and point of zero charge were included to explain the structure of the photocatalyst. The response surface methodology's results show that the optimum CFX efficiency was fully achieved at 94.19%. The optimal conditions with lower standard error (2.08) were given as pH of 5.93, 22.76 ppm of CFX, and 0.46 g L^-1 of the amount of photocatalyst. Besides, the obtained photocatalyst can be easily used many times owing to its high reusability. SWCNT/ZnO/Fe₃O₄ photocatalyst might be recommended to be used for the mineralizing of drug compounds such as antibiotics in water. Moreover, thiazol-2-ol, N-(dihydroxymethyl)-2-(2-hydroxythiazol-4-yl)acetamide,(S)-N-(2-amino-1-hydroxy-2-oxoethyl)-2-(2 hydroxythiazol-4-yl), and 2-(2-hydroxythiazol-4-yl)-N-((2R,3R)-2-mercapto-4-oxoazetidin-3-yl)acetamide were among the detected intermediates products from the cefixime degradation in the process.

Antimicrobial and antifungal properties of NiCu-PANI/PVA quaternary nanocomposite synthesized by chemical oxidative polymerization of polyaniline

Increasing antimicrobial resistance has led to use of novel technologies such as nanomaterials and nanocomposites that have shown effective antimicrobial and/or antifungal activities against several gram-positive and gram-negative bacteria. There have been limited studies on antimicrobial properties of the combined polymer nanocomposites with transitional bimetallic nanoparticles such as nickel (Ni) and copper (Cu). Thus, the main objective of this study was to synthesis, characterize and investigate the antibacterial and antifungal properties of NiCu-PANI/PVA nanocomposite. The nanocomposite films with different amount of Ni and Cu salts were synthesized by chemical oxidative polymerization of polyaniline using HCl as oxidant and PVA as a stabilizer. Optical, chemical composition, and morphological characteristics as well as thermal stability were evaluated using UV-Visible, FTIR, SEM-EDX, and TGA analyses. Antimicrobial properties were then determined using the disc diffusion assay against gram-negative bacteria (i.e., Escherichia coli ATCC 25922, Klebsiella pneumonia ATCC 700603, Proteus sp.,) and gram-positive bacteria (i.e., Staphylococcus aureus ATCC 2593). Fungal plant pathogens including Aspergillus niger and Fusarium oxysporum f. sp. pisi were also evaluated for determination of antifungal activity of NiCu-PANI/PVA films. Among the synthesized films, Ni₆₅Cu₃₅-PANI/PVA showed excellent antibacterial activity against all the bacteria strains examined in this study. The diameters of inhibition zones for Escherichia coli ATCC 25922, Klebsiella pneumoniae ATCC 700603, Proteus sp., and Staphylococcus aureus ATCC 2593 were 23, 23, 17, and 18 mm, respectively indicating good antibacterial activities. Additionally, NiCu-PANI/PVA, particularly the films with higher Cu intake, showed better antifungal activity against Fusarium oxysporum f. sp. pisi. However, NiCu-PANI/PVA was ineffective against Aspergillus niger.

Boron removal from aqueous solutions by chitosan/functionalized-SWCNT-COOH: Development of optimization study using response surface methodology and simulated annealing

Boron contamination in water resources (especially drinking waters and agricultural land) is a major problem for the ecosystem. In this study, a novel synthesized chitosan/functionalized-SWCNT-COOH was prepared to separate boron (as boric acid) from aqueous solutions. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis revealed that SWCNT was dispersed in chitosan homogenously. Moreover, this study has related to the constrained optimization problem with an engineering approach. Response surface method (RSM) with face-centered central composite design (FCCCD) was chosen for maximizing the adsorption capacity as well as determining optimal independent factors such as pH, adsorbent dose, and concentration of boric acid. The optimized response (adsorption capacity) was reached 62.16 mg g^-1 under the optimal conditions (98.77 mg L^-1 of boric acid concentration, pH of 5.46 and 76 min). The present study has indicated that the synthesized material can be used as an adsorbent for eliminating boric acid from aqueous solutions depending on its high adsorbent capacity to remove boron and has better performance than existing adsorbents. Furthermore, simulated annealing (SA) optimization technique was used to compare the findings of RSM. Moreover, the selected optimization techniques were compared with error functions. The optimal conditions derived from SA were 91.17 mg L^-1 of boric acid concentration, pH of 5.86, and 76.17 min. The optimal adsorption capacity of SA was found to be 62.06 mg g^-1. These results revealed that the predictions of the two models are very close to each other.

A comprehensive review on MXenes as new nanomaterials for degradation of hazardous pollutants: Deployment as heterogeneous sonocatalysis

MXene-based nanomaterials (MBNs) are two-dimensional materials that exhibit a series of sought after properties, including rich surface chemistry, adjustable bandgap structures, high electrical conductivity, hydrophobicity, thermal stability, and large specific surface area. MBNs have an exemplar performance when applied for the degradation of hazardous pollutants with various advanced oxidation processes such as heterogeneous sonocatalysis. As such, this work focuses on the sonocatalytic degradation of various hazardous pollutants using MXene-based catalysts. First, the general principles of sonocatalysis are examined, followed by an analysis of the main components of the MXene-based sonocatalysts and their application for pollutant degradation. Lastly, ongoing challenges are highlighted with recommendations to address the issues.