Heavy metal ions retention by bi-functionalized lignin: Synthesis, applications, and adsorption mechanisms

One-Pot Synthesis of Biochar from Industrial Alkali Lignin with Superior Pb(II) Immobilization Capability

This study synthesized biochar through a one-pot pyrolysis process using IALG as the raw material. The physicochemical properties of the resulting biochar (IALG-BC) were characterized and compared with those of biochar derived from acid-treated lignin with the ash component removed (A-IALG-BC). This study further investigated the adsorption performances and mechanisms of these two lignin-based biochars for Pb(II). The results revealed that the high ash content in IALG, primarily composed of Na, acts as an effective catalyst during pyrolysis, reducing the activation energy and promoting the development of the pore structure in the resulting biochar (IALG-BC). Moreover, after pyrolysis, Na-related minerals transformed into particulate matter sized between 80 and 150 nm, which served as active adsorption sites for the efficient immobilization of Pb(II). Adsorption results demonstrated that IALG-BC exhibited a significantly superior adsorption performance for Pb(II) compared to that of A-IALG-BC. The theoretical maximum adsorption capacity of IALG-BC for Pb(II), derived from the Langmuir model, was determined to be 809.09 mg/g, approximately 40 times that of A-IALG-BC. Additionally, the adsorption equilibrium for Pb(II) with IALG-BC was reached within approximately 0.5 h, whereas A-IALG-BC required more than 2 h. These findings demonstrate that the presence of inorganic mineral components in IALG plays a crucial role in its resource utilization.

Hydrothermal Synthesis of a Technical Lignin-Based Nanotube for the Efficient and Selective Removal of Cr(VI) from Aqueous Solution

Aminated lignin (AL) was obtained by modifying technical lignin (TL) with the Mannich reaction, and aminated lignin-based titanate nanotubes (AL-TiNTs) were successfully prepared based on the AL by a facile hydrothermal synthesis method. The characterization of AL-TiNTs showed that a Ti-O bond was introduced into the AL, and the layered and nanotubular structure was formed in the fabrication of the nanotubes. Results showed that the specific surface area increased significantly from 5.9 m2/g (TL) to 188.51 m2/g (AL-TiNTs), indicating the successful modification of TL. The AL-TiNTs quickly adsorbed 86.22% of Cr(VI) in 10 min, with 99.80% removal efficiency after equilibration. Under visible light, AL-TiNTs adsorbed and reduced Cr(VI) in one step, the Cr(III) production rate was 29.76%, and the amount of total chromium (Cr) removal by AL-TiNTs was 90.0 mg/g. AL-TiNTs showed excellent adsorption capacities of Zn2+ (63.78 mg/g), Cd2+ (59.20 mg/g), and Cu2+ (66.35 mg/g). After four cycles, the adsorption capacity of AL-TiNTs still exceeded 40 mg/g. AL-TiNTs showed a high Cr(VI) removal efficiency of 95.86% in simulated wastewater, suggesting a promising practical application in heavy metal removal from wastewater.

Chitosan-based composite hydrogel with a rigid-in-flexible network structure for pH-universal ultra-efficient removal of dye

Polysaccharide-based hydrogel adsorbents become popular because of their high adsorption capacity and fast adsorption rate, but their low removal rate and poor pH resistance have always been fatal shortcomings. Herein, a feasible strategy was proposed to strengthen the ability of hydrogel adsorbent to remove organic pollutants (i.e., dye) by incorporating natural rectorite (REC) into chitosan-g-poly (2-acrylamido-2-methyl-propane-sulfonic-acid) hydrogel network to form a rectorite-in-polymer network structure. The introduction of less dosage of REC (1.2 wt%) into the hydrogel facilitates to improve its adsorption capacities toward methylene blue (MB) in deionized water, tap water, seawater, Yangtze River water, and Yellow River water (1083.39-1303.49 mg/g); while incorporating higher content of REC (15.8 wt% REC) helps to improve the removal rate (99.6 % for MB in real waters), which are greatly superior to commercial activated carbons. The adsorbent keeps high adsorption efficiency in a broad pH range (2-11), and can be reused for >4 times.

Facile green preparation of single- and two-component modified activated carbon fibers for efficient trace heavy metals removal from drinking water

Trace heavy metals exist in drinking water, having great adverse effects on human health and making it a huge challenge to remove. Herein, novel materials have been prepared by a simple and green method using single- (polydopamine (PDA) or 2,3-dimercaptopropanesulfonic sodium (DMPS)) (PDA-OACF or DMPS-OACF) and two-component (PDA and DMPS) (DMPS-PDA-OACF) functionalized activated carbon fibers pretreated by hydrogen peroxide for the removal of trace heavy metals. The as-prepared DMPS-OACF (7.5,20) under DMPS addition of 7.5 mg and sonication time of 20 min retained large specific surface area, micro-mesoporous structure and rich functional groups and showed better adsorption performance for trace lead and mercury. It also exhibited wide applicable ranges of pH (3.50-10.50) and concentration (50-1136 μg L^-1), rapid adsorption kinetics, and excellently selective removal performance for trace lead. The maximum lead adsorption capacity reached 16.03 mg g^-1 when the effluent lead concentration met World Health Organization (WHO) standard and the adsorbent can be regenerated by EDTA solution. The fitting results of adsorption kinetics and isotherm models revealed that the lead adsorption process was multi-site adsorption on heterogeneous surfaces and chemical adsorption. The excellent adsorption properties for trace heavy metals were attributed that the sulfur/oxygen/nitrogen-containing functional groups boosted diffusion and adsorption by electrostatic attraction and coordination, suggesting that DMPS-OACF (7.5,20) has great application potential in the removal of trace heavy metals.

Spirulina platensis Immobilized Alginate Beads for Removal of Pb(II) from Aqueous Solutions

Microalgae contain a diversity of functional groups that can be used as environmental adsorbents. Spirulina platensis is a blue-green microalga that comprises protein-N, which is advantageous for use in nitrogen-containing biomass as adsorbents. This study aimed to enhance the adsorption properties of alginate hydrogels by employing Spirulina platensis. Spirulina platensis was immobilized on sodium alginate (S.P@Ca-SA) via crosslinking. The results of field-emission scanning electron microscopy, Fourier-transform infrared, and X-ray photoelectron spectroscopy analyses of the N-containing functional groups indicated that Spirulina platensis was successfully immobilized on the alginate matrix. We evaluated the effects of pH, concentration, and contact time on Pb(II) adsorption by S.P@Ca-SA. The results demonstrated that S.P@Ca-SA could effectively eliminate Pb(II) at pH 5, reaching equilibrium within 6 h, and the maximum Pb(II) sorption capacity of S.P@Ca-SA was 87.9 mg/g. Our results indicated that S.P@Ca-SA fits well with the pseudo-second-order and Freundlich models. Compared with Spirulina platensis and blank alginate beads, S.P@Ca-SA exhibited an enhanced Pb(II) adsorption efficiency. The correlation implies that the amino groups act as adsorption sites facilitating the elimination of Pb(II).

High-efficiency capture and removal of phosphate from wastewater by 3D hierarchical functional biomass-derived carbon aerogel

The development of functional biomass-based carbon aerogels (CAs) with excellent mechanical flexibility and ultra-high phosphate capture capacity is crucial for capture and recovery of phosphate from waste water. Herein, a functional biomass-derived CA (MgO@SL/CMC CA) with an ordered wave-shaped layered structure and excellent compressibility was fabricated with the aim of creating a material with efficient phosphate capture performance. The incorporation of sulfonomethylated lignin (SL) significantly improves the mechanical flexibility of MgO@SL/CMC CA. Numerous MgO nano-particles (NPs), which act as principal adsorption sites, were uniformly anchored on the MgO@SL/CMC CA. The prepared MgO@SL/CMC CA with high Mg content (20.34 wt%) exhibited an ultra-high phosphate capture capacity (218.51 mg P g^-1 for adsorbent or 644.58 mg P g^-1 for MgO), excellent adsorptive selectivity for phosphate and a wide pH range of application (2-8). Notably, more than 81.95% of the phosphate capture capacity was retained after six cyclic adsorption-desorption tests. A considerable effective treatment volume (468 BV) of actual wastewater (1.7 mg P L^-1) could be achieved by the MgO@SL/CMC CA in the fixed-bed adsorption column. Research into the adsorption mechanism reveals that monolayer chemisorption of phosphate occurs on the MgO@SL/CMC CA through a ligand exchange process. The combination of favorable flexibility, green raw materials and superior phosphate capture performance endows MgO@SL/CMC CA with great application potential in the practical treatment of wastewater.

Facile and green preparation of solid carbon nanoonions via catalytic co-pyrolysis of lignin and polyethylene and their adsorption capability towards Cu(ii)

Carbon nanomaterials, such as carbon nanoonions (CNOs), possess promising applications in various fields. There are urgent demands to synthesize carbon nanomaterials from a green and renewable carbon source. In this study, solid CNOs with relatively uniform size distribution (with diameters of about 30-50 nm), abundant structure defects and oxygen-containing surface functional groups (such as -OH and -COOH) are developed from co-pyrolysis of lignin (LG) and polyethylene (PE) in the presence of Ni-based catalysts. The type of catalyst, the concentration of catalyst and catalytic co-pyrolysis temperature play important roles in the morphologies and properties of CNOs as confirmed by TEM and SEM. Furthermore, the produced CNOs can act as a low-cost and highly-efficient adsorbent to remove Cu(ii) from aqueous solution according to a homogeneous monolayer, chemical action-dominated, endothermic and spontaneous process. The theoretical maximum adsorption capacity of CNOs calculated from the Langmuir model is 100.00 mg g-1. Surface deposition, complexation, π electron-cation interaction and electrostatic interaction are responsible for the adsorption of Cu(ii) using the prepared CNOs.

Next generation applications of lignin derived commodity products, their life cycle, techno-economics and societal analysis

The pulp and biorefining industries produce their waste as lignin, which is one of the most abundant renewable resources. So far, lignin has been remained severely underutilized and generally burnt in a boiler as a low-value fuel. To demonstrate lignin's potential as a value-added product, we will review market opportunities for lignin related applications by utilizing the thermo-chemical/biological depolymerization strategies (with or without catalysts) and their comparative evaluation. The application of lignin and its derived aromatics in various sectors such as cement industry, bitumen modifier, energy materials, agriculture, nanocomposite, biomedical, H2 source, biosensor and bioimaging have been summarized. This comprehensive review article also highlights the technical, economic, environmental, and socio-economic variable that affect the market value of lignin-derived by-products. The review shows the importance of lignin, and its derived products are a platform for future bioeconomy and sustainability.

Enhanced selective adsorption of lead(II) from complex wastewater by DTPA functionalized chitosan-coated magnetic silica nanoparticles based on anion-synergism

Simultaneously removing heavy metal and dye from complex wastewater is of great significance to industrial wastewater treatment. Herein, a novel magnetic adsorbent, DTPA-modified chitosan-coated magnetic silica nanoparticle (FFO@Sil@Chi-DTPA), was successfully prepared and used to enhance the Pb(II) selective adsorption from multi-metal wastewater based on anion-synergism. In the competitive experiment conducted in a multi-ion solution, the type of selective adsorption of metals was changed by the adsorbents before and after amidation, in which FFO@Sil@Chi-DTPA exhibited an excellent selectively for capturing Pb(II), while FFO@Sil@Chi demonstrated highly selective adsorption of silver. More importantly, the selective adsorption of Pb(II)S by FFO@Sil@Chi-DTPA was enhanced from 111.71 to 268.01 mg g^-1 when the coexisting MB concentrations ranged from 0 to 100 mg L^-1 at pH 6.0. In the Pb(II)-MB binary system, Pb(II) and MB exhibited a synergistic effect, in which the presence of MB strengthened the adsorption effect of Pb(II) due to the sulfonic acid groups in MB molecules that create new specific sites for Pb(II) adsorption, while MB adsorption was also enhanced by the presence of Pb(II). This work provides a new strategy for exploring novel adsorbents that can enhance the selective removal of heavy metal in complex wastewater based on anion-synergism.

Removed heavy metal ions from wastewater reuse for chemiluminescence: Successive application of lignin-based composite hydrogels

The novel sulfomethylated lignin-grafted-polyacrylic acid (SL-g-PAA) hydrogel was fabricated in this work via a facile and green synthetic strategy for the efficient removal of heavy metal ions from wastewater, and then successively reused for chemiluminescence (CL). The sulfomethylation of lignin was first performed to improve its water solubility and introduce numerous active sites for adsorption of heavy metal ions. The as-synthesized SL-g-PAA hydrogel with high content of lignin exhibited the highly efficient and rapid removal of various metal ions from simulated wastewater. More importantly, the spent hydrogel (M²⁺@SL-g-PAA) after adsorption was reused for the first time to develop a new CL system by an ingenious strategy, in which these metal ions adsorbed on M²⁺@SL-g-PAA act as heterogeneous catalytic sites to catalyze the CL reaction between N-(4-aminobutyl)-N-ethylisoluminol (ABEI) and H₂O₂. The resultant CL system displayed high CL intensity and long duration time, which could be observed by naked eye in the dark and lasted for > 24 h. The combination of facile fabrication process, renewable raw materials, and ingenious strategy for successive application in adsorption and CL endows this lignin-based composite hydrogel with a great potential for application in wastewater treatment, biological imaging and cold light sources.

Dual lignin-derived polymeric systems for hazardous ion removals

The functionalization of lignin derivatives for ion removals is a promising method to expedite their use in treating industrial wastewater. In this work, kraft lignin (KL) was polymerized with [2-(methacryloyloxy)ethyl]trimethylammonium methyl sulfate (METAM) or acrylic acid (AA) in an acidic aqueous suspension system to produce cationic and anionic water-soluble lignin polymers with high molecular weights. Then, the interaction of soluble ions and KL-METAM and KL-AA was investigated using a Quartz crystal microbalance (QCM) and a vertical scan analyzer (VSA). The QCM, X-ray photoelectron spectroscopy (XPS) and contact angle measurement results showed that the adsorption efficiency of KL-AA was better than KL-METAM for ions due to the stronger electrostatic interaction, cationic π-interaction, and chelation between ions and KL-AA. Based on adsorption, sedimentation, and aggregate size analyses, the dual polymer systems of KL-AA/KL-METAM were more effective than KL-METAM/KL-AA in removing ions. Among Zn²⁺, Cu²⁺, and K⁺; Zn²⁺ interacted more effectively with polymers in all scenarios because it has higher reactivity for interacting with other elements. As the efficiency of ion removals was more remarkable than past reported findings, the system of KL-AA/KL-METAM may be a promising alternative for the removal of dissolved ions from solutions.

Construction of Fe3O4/SiO2/chitosan-grafted-poly(N-vinylcaprolactam) magnetic nanocomposite and their application in simultaneous extraction of Trans-resveratrol and its metabolites from rat plasma

A novel magnetic nanocomposite of chitosan-grafted-poly(N-vinylcaprolactam) (Fe₃O₄/SiO₂/CHT-g-PNVCL MNC) were synthesized. Chitosan was prepared from shrimp shells Penaeus monodon by a green deacetylation approach. N-vinylcaprolactam was first polymerized on the surface of Fe₃O₄ magnetic nanoparticles using surface-initiated atom transfer radical polymerization. Then, the Fe₃O₄ nanoparticles modified with carboxyl-terminated- poly(N-vinylcaprolactam) was grafted onto chitosan. Various techniques were used to characterize of physicochemical properties of synthesized nanomaterials. The application of Fe₃O₄/SiO₂/CHT-g-PNVCL MNC was utilized as a novel adsorbent for the simultaneous extraction of trans-resveratrol and its major phase II metabolites from rat plasma. A qualitative analysis was performed using ultra-performance liquid chromatography triple-quadrupole tandem mass spectrometry. Response surface methodology based on central composite design was used to optimize the extraction procedure including pH, amount of adsorbent, extraction time, desorption time, and volume of elution solvent. The established quantitative method succeeded in satisfying FDA requirements regarding biological analysis methods. The results of the validation of the method indicated its acceptable accuracy (-4.4 to 6.9%), linearity (r > 0.995), precision (CV < 6.3%), and stability. The lower limits of quantification of the proposed method achieved were 1.23-1.68 ngmL^-1for target analytes. The information obtained from the method validation has been used to estimate the expanded uncertainty for the determination of trans-resveratrol in rat plasma samples following orally administered trans-resveratrol. The method was applied to study the pharmacokinetics, metabolism, and bioavailability of trans-resveratrol in healthy rats following a single oral or intravenous dose.

Preparation of EDTA-modified magnetic attapulgite chitosan gel bead adsorbent for the removal of Cu(II), Pb(II), and Ni(II)

Attapulgite (ATP) has a unique porous layered chain structure and is an excellent environment-friendly decolorizer. However, its high viscosity makes it difficult to separate. First, it was combined with magnetic Fe₃O₄ nanoparticles to obtain Fe₃O₄-ATP that is easy to recycle and reuse. Then, Fe₃O₄-ATP nanoparticles were embedded in chitosan (CS) gel beads, and glutaraldehyde was used for cross-linking and curing. Lastly, ethylenediaminetetraacetic acid (EDTA) was successfully connected to Fe₃O₄-ATP/CS gel beads through amidation reaction, which further increased the capability of the adsorbent to adsorb heavy metal ions. The prepared magnetic composite adsorbent is a sphere with a rough surface and porous structure. The maximum adsorption capacity of the prepared Fe₃O₄-ATP/EDTA/CS adsorbent for Pb(II), Cu(II), and Ni(II) is 368.32, 267.94, and 220.31 mg g^-1, respectively. After 5 times of repeated use, Fe₃O₄-ATP/EDTA/CS still showed good adsorption capacity for Cu(II), Pb(II), and Ni(II). Fe₃O₄-ATP/EDTA/CS has a large adsorption capacity for heavy metal ions, a wide pH applicability, good reuse, and rapid magnetic separation. In addition, Cu(II) loaded Fe₃O₄-ATP/EDTA/CS also showed good catalytic degradation performance for bisphenol A. This study prepared a new type of adsorbent with good adsorption performance and provided a promising method for the treatment of wastewater.

Lignin-derived (nano)materials for environmental pollution remediation: Current challenges and future perspectives

The supply of affordable drinking and sufficiently clean water for human consumption is one of the world's foremost environmental problems and a large number of scientific research works are addressing this issue Various hazardous/toxic environmental contaminants in water bodies, both inorganic and organic (specifically heavy metals and dyes), have become a serious global problem. Nowadays, extensive efforts have been made to search for novel, cost effective and practical biosorbents derived from biomass resources with special attention to value added, biomass-based renewable materials. Lignin and (nano)material adorned lignin derived entities can proficiently and cost effectively remove organic/inorganic contaminants from aqueous media. As low cost of preparation is crucial for their wide applications in water/wastewater treatment (particularly industrial water), future investigations must be devoted to refining and processing the economic viability of low cost, green lignin-derived (nano)materials. Production of functionalized lignin, lignin supported metal/metal oxide nanocomposites or hydrogels is one of the effective approaches in (nano)technology. This review outlines recent research progresses, trends/challenges and future prospects about lignin-derived (nano)materials and their sustainable applications in wastewater treatment/purification, specifically focusing on adsorption and/or catalytic reduction/(photo)degradation of a variety of pollutants.

Phosphorylated kraft lignin with improved thermal stability

The low cost, environmental friendliness, and reproducibility of kraft lignin (KL) make it a potential candidate for the development of new green material. The phosphorylation of KL can extend its application as a flame-retardant material. Herein, the phosphorylated kraft lignin (PKL) was systematically fabricated in a sustainable process by utilizing a green phosphating reagent, NH₄H₂PO₄, in the presence of urea. The influence of the reaction parameters, i.e., reaction time and temperature, and NH₄H₂PO₄/lignin ratio on the phosphorylation process were investigated. Advanced characterization techniques including ¹H NMR, ³¹P NMR, and XPS confirmed that the phosphorus groups were successfully introduced to lignin molecules. The active phenolic and aliphatic hydroxy groups of kraft lignin underwent a nucleophilic substitution reaction with the phosphate group to generate phosphorylated lignin. Compared with KL, PKL showed excellent thermal stability, and its maximum decomposition temperature was 620 °C compared with 541 °C for KL.

A systematic review on carbohydrate biopolymers for adsorptive remediation of copper ions from aqueous environments-part A: Classification and modification strategies

Copper is one of the most toxic heavy metals which must be eliminated from aqueous environments, according to the environmental standards. Carbohydrate biopolymers are promising candidates for synthesizing copper-adsorbent composites. It is due to unique properties such as having potential adsorptive functional sites, availability, biocompatibility and biodegradability, formability, blending capacity, and reusability. Different types of copper-adsorbent carbohydrate biopolymers like chitosan and cellulose with particular focus on the synthesizing and modification approaches have been tackled in this review. Composites, functionality and morphological aspects of the biopolymer adsorbents have also been surveyed. Further progress in the fabrication and application of biopolymer adsorbents would be achievable with special attention to some critical challenges such as the process economy, copolymer and/or (nano) additive selection, and the physicochemical stability of the biopolymer composites in aqueous media.

Enhanced heavy metal removal from an aqueous environment using an eco-friendly and sustainable adsorbent

Thiol-lignocellulose sodium bentonite (TLSB) nanocomposites can effectively remove heavy metals from aqueous solutions. TLSB was formed by using -SH group-modified lignocellulose as a raw material, which was intercalated into the interlayers of hierarchical sodium bentonite. Characterization of TLSB was then performed with BET, FTIR, XRD, TGA, PZC, SEM, and TEM analyses. The results indicated that thiol-lignocellulose molecules may have different influences on the physicochemical properties of sodium bentonite, and an intercalated-exfoliated structure was successfully formed. The TLSB nanocomposite was subsequently investigated to validate its adsorption and desorption capacities for the zinc subgroup ions Zn(II), Cd(II) and Hg(II). The optimum adsorption parameters were determined based on the TLSB nanocomposite dosage, concentration of zinc subgroup ions, solution pH, adsorption temperature and adsorption time. The results revealed that the maximum adsorption capacity onto TLSB was 357.29 mg/g for Zn(II), 458.32 mg/g for Cd(II) and 208.12 mg/g for Hg(II). The adsorption kinetics were explained by the pseudo-second-order model, and the adsorption isotherm conformed to the Langmuir model, implying that the dominant chemical adsorption mechanism on TLSB is monolayer coverage. Thermodynamic studies suggested that the adsorption is spontaneous and endothermic. Desorption and regeneration experiments revealed that TLSB could be desorbed with HCl to recover Zn(II) and Cd(II) and with HNO3 to recover Hg(II) after several consecutive adsorption/desorption cycles. The adsorption mechanism was investigated through FTIR, EDX and SEM, which demonstrated that the introduction of thiol groups improved the adsorption capacity. All of these results suggested that TLSB is an eco-friendly and sustainable adsorbent for the extraction of Zn(II), Cd(II) and Hg(II) ions in aqueous media.

Ragauskas A. Recent Advances in the Application of Functionalized Lignin in Value-Added Polymeric Materials

The quest for converting lignin into high-value products has been continuously pursued in the past few decades. In its native form, lignin is a group of heterogeneous polymers comprised of phenylpropanoids. The major commercial lignin streams, including Kraft lignin, lignosulfonates, soda lignin and organosolv lignin, are produced from industrial processes including the paper and pulping industry and emerging lignocellulosic biorefineries. Although lignin has been viewed as a low-cost and renewable feedstock to replace petroleum-based materials, its utilization in polymeric materials has been suppressed due to the low reactivity and inherent physicochemical properties of lignin. Hence, various lignin modification strategies have been developed to overcome these problems. Herein, we review recent progress made in the utilization of functionalized lignins in commodity polymers including thermoset resins, blends/composites, grafted functionalized copolymers and carbon fiber precursors. In the synthesis of thermoset resins such as polyurethane, phenol-formaldehyde and epoxy, they are covalently incorporated into the polymer matrix, and the discussion is focused on chemical modifications improving the reactivity of technical lignins. In blends/composites, functionalization of technical lignins is based upon tuning the intermolecular forces between polymer components. In addition, grafted functional polymers have expanded the utilization of lignin-based copolymers to biomedical materials and value-added additives. Different modification approaches have also been applied to facilitate the application of lignin as carbon fiber precursors, heavy metal adsorbents and nanoparticles. These emerging fields will create new opportunities in cost-effectively integrating the lignin valorization into lignocellulosic biorefineries.

Effect of biochar modified with magnetite nanoparticles and HNO3 for efficient removal of Cr(VI) from contaminated water: A batch and column scale study

Chromium (Cr) poses serious consequences on human and animal health due to its potential carcinogenicity. The present study aims at preparing a novel biochar derived from Chenopodium quinoa crop residues (QBC), its activation with magnetite nanoparticles (QBC/MNPs) and strong acid HNO₃ (QBC/Acid) to evaluate their batch and column scale potential to remove Cr (VI) from polluted water. The QBC, QBC/MNPs and QBC/Acid were characterized with SEM, FTIR, EDX, XRD as well as point of zero charge (PZC) to get an insight into their adsorption mechanism. The impact of different process parameters including dose of the adsorbent (1-4 g/L), contact time (0-180 min), initial concentration of Cr (25-200 mg/L) as well as solution pH (2-8) was evaluated on the Cr (VI) removal from contaminated water. The results revealed that QBC/MNPs proved more effective (73.35-93.62-%) for the Cr (VI) removal with 77.35 mg/g adsorption capacity as compared with QBC/Acid (55.85-79.8%) and QBC (48.85-75.28-%) when Cr concentration was changed from 200 to 25 mg/L. The isothermal experimental results follow the Freundlich adsorption model rather than Langmuir, Temkin and Dubinin-Radushkevich adsorption isotherm models. While kinetic adsorption results were well demonstrated by pseudo second order kinetic model. Column scale experiments conducted at steady state exhibited excellent retention of Cr (VI) by QBC, QBC/MNPs and QBC/Acid at 50 and 100 mg Cr/L. The results showed that this novel biochar (QBC) and its modified forms (QBC/Acid and QBC/MNPs) are applicable with excellent reusability and stability under acidic conditions for the practical treatment of Cr (VI) contaminated water.

Simultaneous removal of methylene blue and Pb2+ from aqueous solution by adsorption on facile modified lignosulfonate

In this paper, simultaneous removal of methylene blue (MB) and Pb²⁺ from the binary component system by an easily prepared cross-linked lignosulfonate bio-adsorbent (CLLS) was described. CLLS was characterized by FTIR, SEM/EDS and TGA. The influences of pH, temperature, contact time and initial MB and Pb²⁺ concentrations on the adsorption performance were investigated. The results demonstrated a good ability of CLLS to remove MB and Pb²⁺ simultaneously. Using of 1.0 g L^-1 loading, removal efficiency of MB and Pb²⁺ reached 98.0% and 97.8%, respectively, in the MB (100 mg.L^-1)-Pb²⁺ (50 mg.L^-1) system. Moreover, the adsorption isotherms and adsorption kinetics indicated that the results were fitting well with the Langmuir and pseudo-second-order model, respectively, for both MB and Pb²⁺. Based on the Langmuir model, the maximum adsorption capacity of MB and Pb²⁺ reached 132.6 and 64.9 mg g^-1, respectively, in the MB-Pb²⁺ system, which was much lower than that in the single component system (358.4 mg g^-1 100.9 mg g^-1 for MB and Pb²⁺, respectively). Hence, simultaneous adsorption of MB and Pb²⁺ onto CLLS was an antagonistic adsorption. In addition, an apart-sequential adsorption method was used to study the action of adsorption sites on CLLS for MB and/or Pb²⁺ with the help of an efficient self-made apparatus. Rudimental results showed that there would be three different kinds of adsorption sites on CLLS: MB-site, Pb²⁺-site and MB/Pb²⁺- shared sites. Furthermore, in the MB (100 mg.L^-1)-Pb²⁺(50.0 mg.L^-1) system, the simultaneous removal efficiency of MB and Pb²⁺ still maintained 91.8% and 85.0%, respectively, after 6 cycles.

Hooped Amino-Group Chains in Porous Organic Polymers for Enhancing Heavy Metal Ion Removal

By adjusting the stretch state of a triethylenetetramine (TETA) chain in an amine-functionalized porous organic polymer (POP), two adsorbents were designed to study the rational microenvironment for heavy metal ion removal. The quantum calculation elucidated that the hooped amino chains in FC-POP-CH₂TETA-H exhibited stronger interactions with Pb(II) than the extended one in FC-POP-CH₂TETA-E, not only through metal-ligand chelation but also metal coordination. The high binding energy of -2624 kJ mol^-1 as well as the constructed microenvironment by the hooped amino chains ensured an extremely high Pb(II) capacity of 1134 mg g^-1 on FC-POP-CH₂TETA-H. Meanwhile, no more than 5 min to approach adsorption equilibrium revealed its ultrafast adsorption rate. It also showed excellent broad removal capability for multiple metal ions and nonsensitivity to pH. Therefore, by controlling the microenvironmental structures with suitable porosity, functional group stretching states, and coordination modes, the removal efficiency of heavy metal ions would be significantly enhanced, which further provided a promising strategy for designing a rational microenvironment to improve the task-specific separation properties.

Composite Membranes Derived from Cellulose and Lignin Sulfonate for Selective Separations and Antifouling Aspects

Cellulose-based membrane materials allow for separations in both aqueous solutions and organic solvents. The addition of nanocomposites into cellulose structure is facilitated through steric interaction and strong hydrogen bonding with the hydroxy groups present within cellulose. An ionic liquid, 1-ethyl-3-methylimidazolium acetate, was used as a solvent for microcrystalline cellulose to incorporate graphene oxide quantum dots into cellulose membranes. In this work, other composite materials such as, iron oxide nanoparticles, polyacrylic acid, and lignin sulfonate have all been uniformly incorporated into cellulose membranes utilizing ionic liquid cosolvents. Integration of iron into cellulose membranes resulted in high selectivity (>99%) of neutral red and methylene blue model dyes separation over salts with a high permeability of 17 LMH/bar. With non-aqueous (alcohol) solvent, iron-cellulose composite membranes become less selective and more permeable, suggesting the interaction of iron ions cellulose OH groups plays a major role in pore structure. Polyacrylic acid was integrated into cellulose membranes to add pH responsive behavior and capacity for metal ion capture. Calcium capture of 55 mg Ca2+/g membrane was observed for PAA-cellulose membranes. Lignin sulfonate was also incorporated into cellulose membranes to add strong negative charge and a steric barrier to enhance antifouling behavior. Lignin sulfonate was also functionalized on the commercial DOW NF270 nanofiltration membranes via esterification of hydroxy groups with carboxyl group present on the membrane surface. Antifouling behavior was observed for both lignin-cellulose composite and commercial membranes functionalized with lignin. Up to 90% recovery of water flux after repeated cycles of fouling was observed for both types of lignin functionalized membranes while flux recovery of up to 60% was observed for unmodified membranes.

Preparation of ion exchange resin using soluble starch and acrylamide by graft polymerization and hydrolysis

Based on soluble starch and acrylamide by performing graft polymerization in aqueous solution and hydrolysis step, a low-cost ion exchange resin has been synthesized to remove the heavy metal ions of Cr³⁺ and Ni²⁺. The hydrolysis progresses by adding NaOH to convert -CONH₂ to -COONa, and the adsorption experiments confirmed that the functional group to adsorb heavy metals is -COO^-, rather than -CONH₂. During the determination of heavy metal adsorption, the Na⁺ concentration diffused by SR-16 into the solution was also analysed to investigate the ion exchange process. The composition and morphology of SR-16 was characterized by FT-IR, SEM, elemental analyser and EDS, and the results showed that SR-16 has an excellent adsorption capacity to the removal of heavy metal pollution; the adsorption mechanism of SR-16 could be explained by ion exchange progress with -COONa attached on the network structure.

Lignin materials for adsorption: Current trend, perspectives and opportunities

Lignin is a highly aromatic low value biomass residue, which can be utilized for chemicals, fuels and materials production. In recent years significant attention has focused on adsorbent materials from lignin. However, only 5% of available lignin is exploited worldwide, thus significant opportunities still exist for materials development. This review summarizes recent research advances in lignin-based adsorbents, with a particular emphasis on lignin, its modification and carbon materials derived from this abundant feedstock. Lignin derived activated carbons have been utilized for air pollutant adsorption (e.g. CO₂, SO₂ and H₂S), while modified lignin materials have been developed for the removal of organic dyes and organics (like methylene blue, Procion Blue MX-R and phenols), heavy metals (such as Cu, Zn, Pb and Cd), or recovery of noble metals (e.g., Pd, Au and Pt). Future perspectives highlight how green chemistry approaches for developing lignin adsorbents can generate added value processes.

Granulated Bog Iron Ores as Sorbents in Passive (Bio)Remediation Systems for Arsenic Removal

The main element of PbRS (passive (bio)remediation systems) are sorbents, which act as natural filters retaining heavy metals and carriers of microorganisms involved in water treatment. Thus, the effectiveness of PbRS is determined by the quality of the (ad)sorbents, which should be stable under various environmental conditions, have a wide range of applications and be non-toxic to (micro)organisms used in these systems. Our previous studies showed that bog iron ores (BIOs) meet these requirements. However, further investigation of the physical and chemical parameters of BIOs under environmental conditions is required before their large-scale application in PbRS. The aim of this study was (i) to investigate the ability of granulated BIOs (gBIOs) to remove arsenic from various types of contaminated waters, and (ii) to estimate the application potential of gBIOs in technologies dedicated to water treatment. These studies were conducted on synthetic solutions of arsenic and environmental samples of arsenic contaminated water using a set of adsorption columns filled with gBIOs. The experiments performed in a static system revealed that gBIOs are appropriate arsenic and zinc adsorbent. Dynamic adsorption studies confirmed these results and showed, that the actual sorption efficiency of gBIOs depends on the adsorbate concentration and is directly proportional to them. Desorption analysis showed that As-loaded gBIOs are characterized by high chemical stability and they may be reused for the (ad)sorption of other elements, i.e., zinc. It was also shown that gBIOs may be used for remediation of both highly oxygenated waters and groundwater or settling ponds, where the oxygen level is low, as both forms of inorganic arsenic (arsenate and arsenite) were effectively removed. Arsenic concentration after treatment was <100 μg/L, which is below the limit for industrial water.

Selective Adsorption of Pb(II) from Aqueous Solution by Triethylenetetramine-Grafted Polyacrylamide/Vermiculite

Amine groups play significant roles in polymeric composites for heavy metals removal. However, generating a composite with a large number of functional and stable amine groups based on clay is still a challenge. In this work, a new amine-functionalized adsorbent based on acid-activated vermiculite (a-Verm) was prepared by organic modification of silane coupling agent as bridge, followed by in situ polymerization of acrylamide (AM) and further grafting of triethylene tetramine (TETA). The obtained polymeric composite g-PAM/OVerm was characterized by scanning electron microscope (SEM), energy dispersive spectrometer (EDS), Fourier transform infrared (FTIR), thermal analysis (TG/DTG), X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) analyses, confirming that amine groups were successfully grafted onto the surface of Verm. The efficacy g-PAM/OVerm for removing Pb(II) was tested. The adsorption equilibrium data on g-PAM/OVerm was in good accordance with the Langmuir adsorption isotherms, and the adsorption maximal value of Pb(II) was 219.4 mg·g⁻¹. The adsorption kinetic data fit the pseudo-second-order kinetic model well. Additionally, g-PAM/OVerm has better selectivity for Pb(II) ion in comparison with Zn(II), Cd(II) and Cu(II) ions. The present work shows that g-PAM/OVerm holds great potential for removing Pb(II) from wastewater, and provides a new and efficient method for the removal of heavy metal ions from industrial wastewater.

One-Step Fabrication of Dual Responsive Lignin Coated Fe₃O₄ Nanoparticles for Efficient Removal of Cationic and Anionic Dyes

A new, simple one-step approach has been developed to synthesize lignin and lignin amine coated Fe₃O₄ nanoparticles. These nanoparticles (lignin magnetic nanoparticles (LMNPs) and lignin amine magnetic nanoparticles (LAMNPs)) are found to possess not only magnetic response but also pH-dependent adsorption behavior. Results show that the combination of lignin with nanoparticles increased the adsorption capacities 2-5 times higher than other traditional single lignin based adsorbents (211.42 mg/g for methylene blue (MB) by LMNPs and 176.49 mg/g for acid scarlet GR (AS-GR) by LAMNPs). Meanwhile, by simply adjusting the pH, the dye-loaded adsorbents can be regenerated to recycle both adsorbents and dyes with a desorption efficiency up to 90%. Mechanistic study shows that dye structure and surface charges of adsorbents play the most important part in adsorption where dyes interact with the adsorbent surface via π-π stacking and electrostatic attraction interactions. The efficient fabrication method, eco-friendly reactant, quick magnetic separation, high adsorption and desorption efficiency suggest this novel type of nano-adsorbents to be promising materials for efficient dye pollutant removal and recovery.

Amination of black liquor and the application in the ready-mixed wet mortar

In order to extend the application of black liquor (BL), amino group was introduced in lignin through Mannich reaction. The structure of the aminated black liquor (ABL) was characterized with FT-IR, elemental analysis, the zeta potential and the inherent viscosity. The foam generated by ABL was more stable, for the surface tension was lower. The results of the mortar test indicated that the water-retention rate of the fresh mortar incorporated with 0.3 wt% ABL was 89.1%; the consistency loss was about 39.7% after 4 h. When the dosage was less than 0.3 wt%, ABL could increase the bond strength of the hardened mortars. The results showed that ABL could be used as an effective ready-mixed wet mortar admixture. This study not only provided a new method to develop new mortar admixture, but also alleviated the pollution of BL.