Preparation and characterization of electrospun alginate/PLA nanofibers as tissue engineering material by emulsion eletrospinning

Non-Woven Fibrous Polylactic Acid/Hydroxyapatite Nanocomposites Obtained via Solution Blow Spinning: Morphology, Thermal and Mechanical Behavior

Polylactic acid (PLA) is widely used in tissue engineering and other biomedical applications. PLA can be modified with appropriate biocompatible ceramic materials since this would allow tailoring the mechanical properties of the tissues to be engineered. In this study, PLA-based non-woven fibrillar nanocomposites containing nanoparticles of hydroxyapatite (HA), a bioceramic commonly used in bone tissue engineering, were prepared via solution blow spinning (SBS). The compositions of the final materials were selected to study the influence of HA concentration on the structure, morphology, and thermal and mechanical properties. The resulting materials were highly porous and mainly constituted fibers. FTIR analysis did not reveal any specific interactions. The diameters of the fibers varied very little with the composition. For example, slightly thinner fibers were obtained for pure PLA and PLA + 10% HA, with fiber diameters of less than 400 nm, while the thicker fibers were found for PLA + 1% HA, with average diameters of 427 ± 170 nm. The crystallinity and stiffness of the PLA/HA composite increased with the HA content. Further, composites containing PLA fibers with slightly larger diameters were more ductile. Thus, with an appropriate balance between factors, such as the diameter of the solution-blow-spun PLA fibers, HA particle content, and degree of crystallinity, PLA/HA composites may be effectively used in tissue engineering applications.

Co-loading of Temozolomide with Oleuropein or rutin into polylactic acid core-shell nanofiber webs inhibit glioblastoma cell by controlled release

Glioblastoma (GB) has susceptibility to post-surgical recurrence. Therefore, local treatment methods are required against recurrent GB cells in the post-surgical area. In this study, we developed a nanofiber-based local therapy against GB cells using Oleuropein (OL), and rutin and their combinations with Temozolomide (TMZ). The polylactic acid (PLA) core-shell nanofiber webs were encapsulated with OL (PLAOL), rutin (PLArutin), and TMZ (PLATMZ) by an electrospinning process. A SEM visualized the morphology and the total immersion method determined the release characteristics of PLA webs. Real-time cell tracking analysis for cell growth, dual Acridine Orange/Propidium Iodide staining for cell viability, a scratch wound healing assay for migration capacity, and a sphere formation assay for tumor spheroid aggressiveness were used. All polymeric nanofiber webs had core-shell structures with an average diameter between 133 ± 30.7-139 ± 20.5 nm. All PLA webs promoted apoptotic cell death, suppressed cell migration, and spheres growth (p < 0.0001). PLAOL and PLATMZ suppressed GB cell viability with a controlled release that increased over 120 h, while PLArutin caused rapid cell inhibition (p < 0.0001). Collectively, our findings suggest that core-shell nano-webs could be a novel and effective therapeutic tool for the controlled release of OL and TMZ against recurrent GB cells.

Fabricating orientated nanofibrous meshes with a bespoke ultra-cost-effective electrospinning machine

Electrospinning's production method has been streamlined and perfected because to advancements in technology and increased demand. While working with electrospun fibers, it is crucial to ensure that they are collected in the correct orientation. Electrospun fibers can be either aligned or random. In contrast to randomly oriented fibers, all aligned ones will point in the same direction. Our results show that a low-cost, tailored electrospinning device can achieve equivalent performance to that of a commercially available system. High voltage (up to 36 kV) and nanofiber orientation adjustments are now being made to the proposed device. A high-voltage direct-current electrical power supply that is custom-built per order and wired by hand. Two specialized collectors, one portable and manufactured from conductive material for random nanofibers, and the other an inexpensive rotational drum collector for aligned nanofibers, have been developed to allow for precise orientation control. By applying Image J software to scanning electron micrographs, we were able to determine the average diameter and orientation of the fibers produced by the electrospinning apparatus, demonstrating its potential to produce nanoscale directed fibers. Because of this research, it's possible that schools will be able to afford an electrospinning system at a price far lower than the current market price.

Bletilla striata composite nanofibrous membranes prepared by emulsion electrospinning for enhanced healing of diabetic wounds

Diabetic wounds impose enormous distress and financial burden on patients, and finding effective dressings to manage wounds is critical. As a Chinese herbal medicine with a long history of Clinical application, Bletilla striata has significant medicinal effects in the therapy of various wounds. In this study, PLA and the pharmacodynamic substances of Bletilla striata were prepared into fibrous scaffolds by emulsion electrospinning technology for the management of diabetic wounds in mice. The results of scanning electron microscopy showed that the core-shell structure fibre was successfully obtained by emulsion electrospinning. The fibre membrane exhibited excellent water absorption capability and water vapor transmission rate, could inhibit the growth of Staphylococcus aureus and Pseudomonas aeruginosa, had good compatibility, and achieved excellent healing effect on diabetic wounds. Especially in the in vivo wound healing experiment, the wound healing rate of composite fibre membrane treatment reached 98.587 ± 2.149% in 16 days. This work demonstrated the good therapeutic effect of the developed fibrous membrane to diabetic wound, and this membrane could be potentially applied to chronic wound healing.

Revolutionizing the Use of Honeybee Products in Healthcare: A Focused Review on Using Bee Pollen as a Potential Adjunct Material for Biomaterial Functionalization

The field of biomedical engineering highly demands technological improvements to allow the successful engraftment of biomaterials requested for healing damaged host tissues, tissue regeneration, and drug delivery. Polymeric materials, particularly natural polymers, are one of the primary suitable materials employed and functionalized to enhance their biocompatibility and thus confer advantageous features after graft implantation. Incorporating bioactive substances from nature is a good technique for expanding or increasing the functionality of biomaterial scaffolds, which may additionally encourage tissue healing. Our ecosystem provides natural resources, like honeybee products, comprising a rich blend of phytochemicals with interesting bioactive properties, which, when functionally coupled with biomedical biomaterials, result in the biomaterial exhibiting anti-inflammatory, antimicrobial, and antioxidant effects. Bee pollen is a sustainable product recently discovered as a new functionalizing agent for biomaterials. This review aims to articulate the general idea of using honeybee products for biomaterial engineering, mainly focusing on describing recent literature on experimental studies on biomaterials functionalized with bee pollen. We have also described the underlying mechanism of the bioactive attributes of bee pollen and shared our perspective on how future biomedical research will benefit from the fabrication of such functionalized biomaterials.

A Critical Review on Classified Excipient Sodium-Alginate-Based Hydrogels: Modification, Characterization, and Application in Soft Tissue Engineering

Alginates are polysaccharides that are produced naturally and can be isolated from brown sea algae and bacteria. Sodium alginate (SA) is utilized extensively in the field of biological soft tissue repair and regeneration owing to its low cost, high biological compatibility, and quick and moderate crosslinking. In addition to their high printability, SA hydrogels have found growing popularity in tissue engineering, particularly due to the advent of 3D bioprinting. There is a developing curiosity in tissue engineering with SA-based composite hydrogels and their potential for further improvement in terms of material modification, the molding process, and their application. This has resulted in numerous productive outcomes. The use of 3D scaffolds for growing cells and tissues in tissue engineering and 3D cell culture is an innovative technique for developing in vitro culture models that mimic the in vivo environment. Especially compared to in vivo models, in vitro models were more ethical and cost-effective, and they stimulate tissue growth. This article discusses the use of sodium alginate (SA) in tissue engineering, focusing on SA modification techniques and providing a comparative examination of the properties of several SA-based hydrogels. This review also covers hydrogel preparation techniques, and a catalogue of patents covering different hydrogel formulations is also discussed. Finally, SA-based hydrogel applications and future research areas concerning SA-based hydrogels in tissue engineering were examined.

Electrospun Food Polysaccharides Loaded with Bioactive Compounds: Fabrication, Release, and Applications

Food polysaccharides are well acclaimed in the field of delivery systems due to their natural safety, biocompatibility with the human body, and capability of incorporating/releasing various bioactive compounds. Electrospinning, a straightforward atomization technique that has been attracting researchers worldwide, is also versatile for coupling food polysaccharides and bioactive compounds. In this review, several popular food polysaccharides including starch, cyclodextrin, chitosan, alginate, and hyaluronic acid are selected to discuss their basic characteristics, electrospinning conditions, bioactive compound release characteristics, and more. Data revealed that the selected polysaccharides are capable of releasing bioactive compounds from as rapidly as 5 s to as prolonged as 15 days. In addition, a series of frequently studied physical/chemical/biomedical applications utilizing electrospun food polysaccharides with bioactive compounds are also selected and discussed. These promising applications include but are not limited to active packaging with 4-log reduction against E. coli, L. innocua, and S. aureus; removal of 95% of particulate matter (PM) 2.5 and volatile organic compounds (VOCs); heavy metal ion removal; increasing enzyme heat/pH stability; wound healing acceleration and enhanced blood coagulation, etc. The broad potentials of electrospun food polysaccharides loaded with bioactive compounds are demonstrated in this review.

Ethanol-free Cross-Linking of Alginate Nanofibers Enables Controlled Release into a Simulated Gastrointestinal Tract Model

The use of alginate nanofibers in certain biomedical applications, including targeted delivery to the gut, is limited because an ethanol-free, biocompatible cross-linking method has not been demonstrated. Here, we developed water-stable, alginate-based nanofibers by systematically exploring post-electrospinning cross-linking approaches that used calcium ions dissolved in (1) a glycerol/water cosolvent system and (2) acidic, neutral, or basic aqueous solutions. Scanning electron microscopy proved that the fibers cross-linked in a glycerol cosolvent or pH-optimized solutions had maintained the same morphology as the ethanol-based literature control. Notably, cross-linked fibers were generally smaller in diameter than the as-spun fibers due to both chemical interactions and mass loss during cross-linking, which was supported by mass measurements, Fourier-transform infrared spectroscopy, and thermogravimetric analysis. During stability tests wherein the cross-linked fibers were exposed to three aqueous solutions, the cross-linked fibers were stable in water and acid buffer yet swelled in phosphate buffer saline, making them useful scaffolds for pH-controlled release applications. Proof-of-concept release experiments were conducted using a simulated gastrointestinal tract model. As desired, the cargo remained encapsulated within the cross-linked nanofibers when exposed to an acidic solution that modeled the stomach. Upon exposure to a solution that mimicked the intestines, the cargo was released. We suggest that these cross-linked, alginate-based nanofiber mats hold the potential to be broadly used in biomedical and environmental applications.

Modification, 3D printing process and application of sodium alginate based hydrogels in soft tissue engineering: A review

Sodium alginate (SA) is an inexpensive and biocompatible biomaterial with fast and gentle crosslinking that has been widely used in biological soft tissue repair/regeneration. Especially with the advent of 3D bioprinting technology, SA hydrogels have been applied more deeply in tissue engineering due to their excellent printability. Currently, the research on material modification, molding process and application of SA-based composite hydrogels has become a hot topic in tissue engineering, and a lot of fruitful results have been achieved. To better help readers have a comprehensive understanding of the development status of SA based hydrogels and their molding process in tissue engineering, in this review, we summarized SA modification methods, and provided a comparative analysis of the characteristics of various SA based hydrogels. Secondly, various molding methods of SA based hydrogels were introduced, the processing characteristics and the applications of different molding methods were analyzed and compared. Finally, the applications of SA based hydrogels in tissue engineering were reviewed, the challenges in their applications were also analyzed, and the future research directions were prospected. We believe this review is of great helpful for the researchers working in biomedical and tissue engineering.

Centrifugally spun poly(D,L-lactic acid)-alginate composite microbeads for drug delivery and tissue engineering

This work was based on medium-viscosity alginate as a minor constituent in composites with poly lactic acid (PLA) with the objective to prepare compositional variants through Forcespinning® (FS); for future medical applications. Composites within 0.08-0.25 wt% medium-viscosity alginate were used, at fixed PLA, 6.6 wt%, compared with a study using 0.17-0.48 wt% low-viscosity alginate (same PLA), starting from water-in-oil emulsions, before FS. The presence of alginate is proposed here to influence the high surface tension existing at the emulsion water/oil interface, reducing the total energy at this interface, and/or facilitating the particles in the amphiphilic blend to lie-flat (re-orient) for better fit to the PLA curvature. The study revealed a direct correlation of the inner-phase size (alginate/water ratio), to the change in the morphology and structure of the resultant composites before and after FS. The change in the alginate type, revealed characteristics better suited for medical applications by the medium-viscosity alginate. Composites at alginate- medium-viscosity; ≤0.25 wt%, and low-viscosity; ≤0.48 wt%, had fiber networks interwoven with micro-beads, with characteristics better suited for controlled-release drug delivery applications. Alternatively, each alginate type at 1.1 wt%, composites with PLA at 6.6 wt% could bring about homogenous fibrous materials better suited for wound dressing.

Electrospun polylactic acid scaffolds with strontium- and cobalt-doped bioglass for potential use in bone tissue engineering applications

The development of nanoscale biomaterials associated with polymers has been growing over the years, due to their important structural characteristics for applications in biological systems. The present study aimed to produce and test polymeric scaffolds composed of polylactic acid (PLA) fibers associated with a 58S bioglass doped with therapeutic ions for use in tissue engineering. Three 58S Bioglass was obtained by the sol-gel route, pure and doped with 5% strontium and cobalt ions. Solutions of 7% PLA was used as control and added the three different bioglass, 4% of 58S bioglass (PLA-BG), 4% bioglass-doped strontium (PLA-BGSr) and 4% bioglass-doped cobalt (PLA-BGCo). Scaffolds were produced through electrospinning process, and was characterized chemical and morphologically. The in vitro tests were performed using mesenchymal cells cultures from femurs of nine rats, grown in osteogenic supplemented total culture medium. After osteoblastic differentiation induction cell viability, alkaline phosphatase activity, total protein content quantification, and visualization of mineralization nodule tests were performed. Analysis of normal distribution used the Shapiro-Wilk test (nanofibers diameter and biological assay). Data were compared using the Kruskal-Wallis nonparametric test (p = 0.05). The bioglasses produced proved to be free of nitrate, chlorinated and nano-sized, with effective incorporation of therapeutic ions in their structure. All materials showed cell viability (>70%), total protein production, and alkaline phosphatase activity. It was possible to develop polylactic acid scaffolds associated with 58S bioglass doped with therapeutic ions without cytotoxicity. Scaffolds characteristics appear to sustain its application in bone tissue engineering.

Novel Electrospun Polycaprolactone/Calcium Alginate Scaffolds for Skin Tissue Engineering

After decades of research, fully functional skin regeneration is still a challenge. Skin is a multilayered complex organ exhibiting a cascading healing process affected by various mechanisms. Specifically, nutrients, oxygen, and biochemical signals can lead to specific cell behavior, ultimately conducive to the formation of high-quality tissue. This biomolecular exchange can be tuned through scaffold engineering, one of the leading fields in skin substitutes and equivalents. The principal objective of this investigation was the design, fabrication, and evaluation of a new class of three-dimensional fibrous scaffolds consisting of poly(ε-caprolactone) (PCL)/calcium alginate (CA), with the goal to induce keratinocyte differentiation through the action of calcium leaching. Scaffolds fabricated by electrospinning using a PCL/sodium alginate solution were treated by immersion in a calcium chloride solution to replace alginate-linked sodium ions by calcium ions. This treatment not only provided ion replacement, but also induced fiber crosslinking. The scaffold morphology was examined by scanning electron microscopy and systematically assessed by measurements of the pore size and the diameter, alignment, and crosslinking of the fibers. The hydrophilicity of the scaffolds was quantified by contact angle measurements and was correlated to the augmentation of cell attachment in the presence of CA. The in vitro performance of the scaffolds was investigated by seeding and staining fibroblasts and keratinocytes and using differentiation markers to detect the evolution of basal, spinous, and granular keratinocytes. The results of this study illuminate the potential of the PCL/CA scaffolds for tissue engineering and suggest that calcium leaching out from the scaffolds might have contributed to the development of a desirable biological environment for the attachment, proliferation, and differentiation of the main skin cells (i.e., fibroblasts and keratinocytes).

Centrifugally spun alginate-poly(lactic acid) microbeads: A promising carrier for drug delivery and tissue engineering

A facile and high yield centrifugal spinning technique known as Forcespinning® (FS) was used to develop unique microstructures consisting of PLA microbeads along alginate fibers. Morphological variation and structural features appeared in the field-emission scanning electron micrographs for the PLA-alginate composites and dried PLA-alginate films from precursor emulsions at constant PLA and varied alginate contents. Shrunk and deflated microbeads were observed for composites whilst spherical beads were evident for the PLA control. Furthermore, PLA was found surrounding the alginate when the alginate was present at 0.24 wt% or lower, while alginate (mushroom-like structures), were seen protruding through the PLA layer at ≥0.34 wt% alginate. Rheological characterization of the composite emulsions revealed that the filler (alginate) provided shear thinning properties including pseudoplasticity, desirable for printing and other related applications in contrast to the Newtonian flow shown by the PLA control. Along with infra-red spectroscopy, the nanocomposites were further characterized using thermal gravimetry and differential scanning calorimetry featuring reversible events influenced by heat capacity and irreversible kinetic/thermodynamic counterparts. The work provides a comprehensive investigation of biocompatible networks of PLA-alginate microbeads embedded in nano-sized fibers and the prospective application of these microbeads as a drug delivery system.

Alginate-Based Bio-Composites and Their Potential Applications

Over the last two decades, bio-polymer fibers have attracted attention for their uses in gene therapy, tissue engineering, wound-healing, and controlled drug delivery. The most commonly used bio-polymers are bio-sourced synthetic polymers such as poly (glycolic acid), poly (lactic acid), poly (e-caprolactone), copolymers of polyglycolide and poly (3-hydroxybutyrate), and natural polymers such as chitosan, soy protein, and alginate. Among all of the bio-polymer fibers, alginate is endowed with its ease of sol–gel transformation, remarkable ion exchange properties, and acid stability. Blending alginate fibers with a wide range of other materials has certainly opened many new opportunities for applications. This paper presents an overview on the modification of alginate fibers with nano-particles, adhesive peptides, and natural or synthetic polymers, in order to enhance their properties. The application of alginate fibers in several areas such as cosmetics, sensors, drug delivery, tissue engineering, and water treatment are investigated. The first section is a brief theoretical background regarding the definition, the source, and the structure of alginate. The second part deals with the physico-chemical, structural, and biological properties of alginate bio-polymers. The third part presents the spinning techniques and the effects of the process and solution parameters on the thermo-mechanical and physico-chemical properties of alginate fibers. Then, the fourth part presents the additives used as fillers in order to improve the properties of alginate fibers. Finally, the last section covers the practical applications of alginate composite fibers.

Alginate-based nanocarriers for the delivery and controlled-release of bioactive compounds

Alginate-based nanocarriers are propitious vehicles used for the delivery of bioactive compounds (bioactives). In this area, calcium alginate and sodium alginate are the most promising wall materials because they are nontoxic, comparatively cheap, simple in production, biocompatible and biodegradable. In this review, we have highlighted different alginate-based nanocarriers such as nanoparticles, nanofibers, nanoemulsions, nanocomplexes, and nanohydrogels; also entrapment of different bioactives within alginate nanocarriers and their bioavailability in the gastric environment has been comprehensively discussed. Being biopolymers, alginates can be exploited as emulsifiers/ encapsulants for entrapment and delivery of different bioactives such as vitamins, minerals, essential fatty acids, peptides, essential oils, bioactive oils, polyphenols and carotenoids. Furthermore, the use of alginate-based nanocarriers in combination with other polysaccharides/ emulsifiers was recognized as the most effective and favorable approach for the protection, delivery and sustained release of bioactives.

Biopolymer-based nanocarriers for sustained release of agrochemicals: A review on materials and social science perspectives for a sustainable future of agri- and horticulture

Devastating plant diseases and soil depletion rationalize an extensive use of agrochemicals to secure the food production worldwide. The sustained release of fertilizers and pesticides in agriculture is a promising solution to the eco-toxicological impacts and it might reduce the amount and increase the effectiveness of agrochemicals administration in the field. This review article focusses on carriers with diameters below 1 μm, such as capsules, spheres, tubes and micelles that promote the sustained release of actives. Biopolymer nanocarriers represent a potentially environmentally friendly alternative due to their renewable origin and biodegradability, which prevents the formation of microplastics. The social aspects, economic potential, and success of commercialization of biopolymer based nanocarriers are influenced by the controversial nature of nanotechnology and depend on the use case. Nanotechnology's enormous innovative power is only able to unfold its potential to limit the effects of climate change and to counteract current environmental developments if the perceived risks are understood and mitigated.

Special Features of Polyester-Based Materials for Medical Applications

This article presents current possibilities of using polyester-based materials in hard and soft tissue engineering, wound dressings, surgical implants, vascular reconstructive surgery, ophthalmology, and other medical applications. The review summarizes the recent literature on the key features of processing methods and potential suitable combinations of polyester-based materials with improved physicochemical and biological properties that meet the specific requirements for selected medical fields. The polyester materials used in multiresistant infection prevention, including during the COVID-19 pandemic, as well as aspects covering environmental concerns, current risks and limitations, and potential future directions are also addressed. Depending on the different features of polyester types, as well as their specific medical applications, it can be generally estimated that 25–50% polyesters are used in the medical field, while an increase of at least 20% has been achieved since the COVID-19 pandemic started. The remaining percentage is provided by other types of natural or synthetic polymers; i.e., 25% polyolefins in personal protection equipment (PPE).

Preparations of Poly(lactic acid) Dispersions in Water for Coating Applications

A green, effective methodology for the preparation of water-based dispersions of poly(lactic acid) (PLA) for coating purposes is herein presented. The procedure consists of two steps: in the first one, an oil-in-water emulsion is obtained by mixing a solution of PLA in ethyl acetate with a water phase containing surfactant and stabilizer. Different homogenization methods as well as oil/water phase ratio, surfactant and stabilizer combinations were screened. In the second step, the quantitative evaporation of the organic provides water dispersions of PLA that are stable, at least, over several weeks at room temperature or at 4 °C. Particle size was in the 200-500 nm range, depending on the preparation conditions, as confirmed by scanning electron microscope (SEM) analysis. PLA was found not to suffer significant molecular weight degradation by gel permeation chromatography (GPC) analysis. Furthermore, two selected formulations with glass transition temperature (Tg) of 51 °C and 34 °C were tested for the preparation of PLA films by drying in PTFE capsules. In both cases, continuous films that are homogeneous by Fourier-transform infrared spectroscopy (FT-IR) and SEM observation were obtained only when drying was performed above 60 °C. The formulation with lower Tg results in films which are more flexible and transparent.

Electrospun Nanofibrous Membranes for Tissue Engineering and Cell Growth

In biotechnology, the field of cell cultivation is highly relevant. Cultivated cells can be used, for example, for the development of biopharmaceuticals and in tissue engineering. Commonly, mammalian cells are grown in bioreactors, T-flasks, well plates, etc., without a specific substrate. Nanofibrous mats, however, have been reported to promote cell growth, adhesion, and proliferation. Here, we give an overview of the different attempts at cultivating mammalian cells on electrospun nanofiber mats for biotechnological and biomedical purposes. Starting with a brief overview of the different electrospinning methods, resulting in random or defined fiber orientations in the nanofiber mats, we describe the typical materials used in cell growth applications in biotechnology and tissue engineering. The influence of using different surface morphologies and polymers or polymer blends on the possible application of such nanofiber mats for tissue engineering and other biotechnological applications is discussed. Polymer blends, in particular, can often be used to reach the required combination of mechanical and biological properties, making such nanofiber mats highly suitable for tissue engineering and other biotechnological or biomedical cell growth applications.

Bacterial Photoinactivation Using PLGA Electrospun Scaffolds

The use of ultraviolet (UV) and blue irradiation to sterilize surfaces is well established, but commercial applications would be enhanced if the light source is replaced with ambient light. In this paper, it is shown that nanofibers can be explored as an alternative methodology to UV and blue irradiation for bacterial inactivation. It is demonstrated that this is indeed possible using spun nanofibers of poly[lactic-co-(glycolic acid)] (PLGA). This work shows that PLGA spun scaffolds can promote photoinactivation of Staphylococcus aureus and Escherichia coli bacteria with ambient light or with laser irradiation at 630 nm. With the optimized scaffold composition of PLGA85:15 nanofibers, the minimum intensity required to kill the bacteria is much lower than in antimicrobial blue light applications. The enhanced effect introduced by PLGA scaffolds is due to their nanofiber structures since PLGA spun nanofibers were able to inactivate both S. aureus and E. coli bacteria, but cast films had no effect. These findings pave the way for an entirely different method to sterilize surfaces, which is less costly and environmentally friendly than current procedures. In addition, the scaffolds could also be used in cancer treatment with fewer side effects since photosensitizers are not required.

Green Approach to Develop Bee Pollen-Loaded Alginate Based Nanofibrous Mat

Green electrospun materials are gaining popularity in the quest for a more sustainable environment for human life. Bee pollen (BP) is a valuable apitherapeutic product and has many beneficial features such as antioxidant and antibacterial properties. Alginate is a natural and low-cost polymer. Both natural materials show good compatibility with human tissues for biomedical applications and have no toxic effect on the environment. In this study, bee pollen-loaded sodium alginate and polyvinyl alcohol (SA/PVA) nanofibrous mats were fabricated by the electrospinning technique. The green electrospun nanofibrous mats were analyzed by scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), and differential scanning calorimeter (DSC). According to the findings of the study, the toxin-free electrospinning method is suitable for producing green nanomaterial. Because of the useful properties of the bee pollen and the favorable biocompatibility of the alginate fibers, the bee pollen-loaded SA/PVA electrospun mats have the potential for use in a variety of biomedical applications.

Hybrid Filaments from Saccaharina lattisima Biomass: Engineering of Alginate Properties with Maleic Anhydride Grafted Linseed Oil

Linseed oil was graft modified with maleic anhydride and introduced into alginate by co-extrusion, producing alginate hybrid filaments. A straightforward grafting of maleic anhydride onto the oil backbone produced the modified oil. Additional esterification with n-dodecanol was also investigated. The structures of the modified oils were verified with 2D-NMR. The modified oil was mixed with alginate and extruded into CaCl2, forming thin filaments with diameters in the 130-260 μm range. The impact of oil integration into the alginate filaments was assessed, with special emphasis on stress-at-break, and compared to values predicted by an empirical model relating the "stress to alginate concentration" ratio to prevailing conditions during filament drawing. Analogous alginate filaments were prepared with hydrochloric-, oxalic- and phytic acid calcium salts for comparison with alginate-oil hybrids to reveal the induced impact, with respect to the composition and charge, on the tensile performance.

Detecting and targeting neurodegenerative disorders using electrospun nanofibrous matrices: current status and applications

Neurodegeneration is defined as the progressive atrophy and loss of function of neurons; it is present in neurodegenerative disorders such as Multiple Sclerosis, Alzheimer's, Huntington's, and Parkinson's diseases. The detection of such disorders is performed by various imaging modalities while their therapeutic management is quite challenging. Besides, the pathogenesis of neurodegenerative disorders is still under ongoing research due to complex and multi-factorial mechanisms. Currently, targeting the specific proteins responsible for neurodegeneration is of great interest to many researchers. Furthermore, nanotechnology-based approaches for targeting the affected neurons became an emerging field of interest. Nanostructures of various forms have been developed aiming to act as therapeutics for neurodegeneration, in which electrospun nanofibers seem to play an important role as biomedical products for both detection and management of the diseases. Electrospinning is an intriguing method able to produce nanofibers with a wide range of sizes and morphological characteristics. Such nanofibrous matrices can be delivered through different administration routes to target various diseases. In this review, the most recent advancements in electrospun nanofibrous systems that target or detect multiple neurodegenerative diseases have been enlightened and an introduction to the general aspects of neurodegenerative diseases and the electrospinning process has been made. Finally, future perspectives of neurodegeneration targeting were also discussed.

How does counter-cation substitution influence inter- and intramolecular hydrogen bonding and electrospinnability of alginates

Despite numerous applications of nanofibrous alginate (Alg) mat, its facile fabrication via electrospinning is still challenging. The low alginate content compared to the carrier polymer and existence of impurities are the main drawbacks of existing approaches. The purpose of this research is both to study and improve alginate electrospinnability by focusing on the effect of inter- and intramolecular hydrogen bonding. Based on hard and soft acids and bases (HSAB) theory, the Na⁺ cations (carboxylate counter-cation) were substituted with a harder acid, Li⁺ cation, to increase the strength of ionic interaction and decrease the density of hydrogen bonding. Viscosity and electrical conductivity measurements as well as FTIR and ¹H NMR revealed a lower intramolecular hydrogen bonding density in Li-Alg. SEM images showed improvement of alginate electrospinnability for Li-Alg compared to the salts of Na-Alg and K-Alg. This study sheds more light on underlying reasons hindering alginate electrospinning and introduces a simple method for fabrication of nanofibers with high alginate content.

Physical Properties, Chemical Analysis, and Evaluation of Antimicrobial Response of New Polylactide/Alginate/Copper Composite Materials

In recent years, due to an expansion of antibiotic-resistant microorganisms, there has been growing interest in biodegradable and antibacterial polymers that can be used in selected biomedical applications. The present work describes the synthesis of antimicrobial polylactide-copper alginate (PLA-ALG-Cu2+) composite fibers and their characterization. The composites were prepared by immersing PLA fibers in aqueous solution of sodium alginate, followed by ionic cross-linking of alginate chains within the polylactide fibers with Cu(II) ions to yield PLA-ALG-Cu2+ composite fibers. The composites, so prepared, were characterized by scanning electron microscopy (SEM), UV/VIS transmittance and attenuated total reflection Fourier-transform infrared spectroscopy ATR-FTIR, and by determination of their specific surface area (SSA), total/average pore volumes (through application of the 5-point Brunauer-Emmett-Teller method (BET)), and ability to block UV radiation (determination of the ultraviolet protection factor (UPF) of samples). The composites were also subjected to in vitro antimicrobial activity evaluation tests against colonies of Gram-negative (E. coli) and Gram-positive (S. aureus) bacteria and antifungal susceptibility tests against Aspergillus niger and Chaetomium globosum fungal mold species. All the results obtained in this work showed that the obtained composites were promising materials to be used as an antimicrobial wound dressing.

Biomimetic Polyurethane 3D Scaffolds Based on Polytetrahydrofuran Glycol and Polyethylene Glycol for Soft Tissue Engineering

In this study, a novel polyurethane porous 3D scaffold based on polyethylene glycol (PEG) and polytetrahydrofuran glycol (PTMG) was developed by in situ polymerization and freeze drying. Aliphatic hexamethylene diisocyanate (HDI) as a nontoxic and safe agent was adopted to produce the rigid segment in polyurethane polymerization. The chemical structure, macrostructure, and morphology—as well as mechanical strength of the scaffolds—were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), and tensile tests. The results show that the HDI can react mildly with hydroxyl (–OH) groups of PEG and PTMG, while gas foaming action caused by the release of CO₂ occurred simultaneously in the reactive process, resulting in a uniform porous structure of PU scaffold. Moreover, the scaffolds were soaked in water and freeze dried to obtain higher porosity and more interconnective microstructures. The scaffolds have a porosity of over 70% and pore size from 100 to 800 μm. The mechanical properties increased with increasing PEG content, while the hydrophilicity increased as well. After immersion in simulated body fluid (SBF), the scaffolds presented a stable surface structure. The gas foaming/freezing drying process is an excellent method to prepare skin tissue engineering scaffold from PTMG/PEG materials with high porosity and good inter connectivity.

Nanofiber Technology for Regenerative Engineering

Regenerative engineering is powerfully emerging as a successful strategy for the regeneration of complex tissues and biological organs using a convergent approach that integrates several fields of expertise. This innovative and disruptive approach has spurred the demands for more choice of biomaterials with distinctive biological recognition properties. An ideal biomaterial is one that closely mimics the hierarchical architecture and features of the extracellular matrices (ECM) of native tissues. Nanofabrication technology presents an excellent springboard for the development of nanofiber scaffolds that can have positive interactions in the immediate cellular environment and stimulate specific regenerative cascades at the molecular level to yield healthy tissues. This paper systematically reviews the electrospinning process technology and its utility in matrix-based regenerative engineering, focusing mainly on musculoskeletal tissues. It briefly outlines the electrospinning/three-dimensional printing system duality and concludes with a discussion on the technology outlook and future directions of nanofiber matrices.

Biodegradable engineered fiber scaffolds fabricated by electrospinning for periodontal tissue regeneration

Considering the specificity of periodontium and the unique advantages of electrospinning, this technology has been used to fabricate biodegradable tissue engineering materials for functional periodontal regeneration. For better biomedical quality, a continuous technological progress of electrospinning has been performed. Based on property of materials (natural, synthetic or composites) and additive novel methods (drug loading, surface modification, structure adjustment or 3 D technique), various novel membranes and scaffolds that could not only relief inflammation but also influence the biological behaviors of cells have been fabricated to achieve more effective periodontal regeneration. This review provides an overview of the usage of electrospinning materials in treatments of periodontitis, in order to get to know the existing research situation and find treatment breakthroughs of the periodontal diseases.

Electrospun Alginate Nanofibers Toward Various Applications: A Review

Alginate has been a material of choice for a spectrum of applications, ranging from metal adsorption to wound dressing. Electrospinning has added a new dimension to polymeric materials, including alginate, which can be processed to their nanosize levels in order to afford unique nanostructured materials with fascinating properties. The resulting nanostructured materials often feature high porosity, stability, permeability, and a large surface-to-volume ratio. In the present review, recent trends on electrospun alginate nanofibers from over the past 10 years toward advanced applications are discussed. The application of electrospun alginate nanofibers in various fields such as bioremediation, scaffolds for skin tissue engineering, drug delivery, and sensors are also elucidated.

Current Applications of Biopolymer-based Scaffolds and Nanofibers as Drug Delivery Systems

BACKGROUND

The high surface-to-volume ratio of polymeric nanofibers makes them an effective vehicle for the release of bioactive molecules and compounds such as growth factors, drugs, herbal extracts and gene sequences. Synthetic polymers are commonly used as sensors, reinforcements and energy storage, whereas natural polymers are more prone to mimicking an extracellular matrix. Natural polymers are a renewable resource and classified as an environmentally friendly material, which might be used in different techniques to produce nanofibers for biomedical applications such as tissue engineering, implantable medical devices, antimicrobial barriers and wound dressings, among others. This review sheds some light on the advantages of natural over synthetic polymeric materials for nanofiber production. Also, the most important techniques employed to produce natural nanofibers are presented. Moreover, some pieces of evidence regarding toxicology and cell-interactions using natural nanofibers are discussed. Clearly, the potential extrapolation of such laboratory results into human health application should be addressed cautiously.

Digital Design and Automated Fabrication of Bespoke Collagen Microfiber Scaffolds

A great variety of natural and synthetic polymer materials have been utilized in soft tissue engineering as extracellular matrix (ECM) materials. Natural polymers, such as collagen and fibrin hydrogels, have experienced especially broad adoption due to the high density of cell adhesion sites compared to their synthetic counterparts, ready availability, and ease of use. However, these and other hydrogels lack the structural and mechanical anisotropy that define the ECM in many tissues, such as skeletal and cardiac muscle, tendon, and cartilage. Herein, we present a facile, low-cost, and automated method of preparing collagen microfibers, organizing these fibers into precisely controlled mesh designs, and embedding these meshes in a bulk hydrogel, creating a composite biomaterial suitable for a wide variety of tissue engineering and regenerative medicine applications. With the assistance of custom software tools described herein, mesh patterns are designed by a digital graphical user interface and translated into protocols that are executed by a custom mesh collection and organization device. We demonstrate a high degree of precision and reproducibility in both fiber and mesh fabrication, evaluate single fiber mechanical properties, and provide evidence of collagen self-assembly in the microfibers under standard cell culture conditions. This work offers a powerful, flexible platform for the study of tissue engineering and cell material interactions, as well as the development of therapeutic biomaterials in the form of custom collagen microfiber patterns that will be accessible to all through the methods and techniques described here. Impact Statement Collagen microfiber meshes have immediate and broad applications in tissue engineering research and show high potential for later use in clinical therapeutics due to their compositional similarities to native extracellular matrix and tunable structural and mechanical characteristics. Physical and biological characterizations of these meshes demonstrate physiologically relevant mechanical properties, native-like collagen structure, and cytocompatibility. The methods presented herein not only describe a process through which custom collagen microfiber meshes can be fabricated but also provide the reader with detailed device plans and software tools to produce their own bespoke meshes through a precise, consistent, and automated process.

Fabrication of electrospun poly(lactic acid) nanoporous membrane loaded with niobium pentoxide nanoparticles as a potential scaffold for biomaterial applications

Tissue engineering aims to regenerate and restore damaged human organs and tissues using scaffolds that can mimic the native tissues. The requirement for modern and efficient biomaterials that are capable of accelerating the healing process has been considerably increased. In this work, a novel electrospun poly(lactic acid) (PLA) nanoporous membrane incorporated with niobium pentoxide nanoparticles (Nb₂ O₅ ) for biomaterial applications was developed. Nb₂ O₅ nanoparticles were obtained by microwave-assisted hydrothermal synthesis, and different concentrations (0, 1, 3, and 5% wt/wt) were tested. Chemical, morphological, mechanical, and biological properties of membranes were evaluated. Cell viability results demonstrated that the membranes presented nontoxic effects. The incorporation of Nb₂ O₅ improved cell proliferation without impairing the wettability, porosity, and mechanical properties of membranes. Membranes containing Nb₂ O₅ nanoparticles presented biocompatible properties with suitable porosity, which facilitated cell attachment and proliferation while allowing diffusion of oxygen and nutrients. This study has demonstrated that Nb₂ O₅ nanoparticle-loaded electrospun PLA nanoporous membranes are potential candidates for drug delivery and wound dressing applications.