Cu-bearing high-entropy alloys with excellent antiviral properties

Influence of Zirconium on the Microstructure, Selected Mechanical Properties, and Corrosion Resistance of Ti20Ta20Nb20(HfMo)20-xZrx High-Entropy Alloys

The presented work considers the influence of the hafnium and molybdenum to zirconium ratio of Ti20Ta20Nb20(HfMo)20-xZrx (where x = 0, 5, 10, 15, 20 at.%) high-entropy alloys in an as-cast state for potential biomedical applications. The current research continues with our previous results of hafnium's and molybdenum's influence on a similar chemical composition. In the presented study, the microstructure, selected mechanical properties, and corrosion resistance were investigated. The phase formation thermodynamical calculations were also applied to predict solid solution formation after solidification. The calculations predicted the presence of multi-phase, body-centred cubic phases, confirmed using X-ray diffraction and scanning electron microscopy. The chemical composition analysis showed the segregation of alloying elements. Microhardness measurements revealed a decrease in microhardness with increased zirconium content in the studied alloys. The corrosion resistance was determined in Ringer's solution to be higher than that of commercially applied biomaterials. The comparison of the obtained results with previously reported data is also presented and discussed in the presented study.

Nanoprecipitates to Enhance Radiation Tolerance in High-Entropy Alloys

The growth of advanced energy technologies for power generation is enabled by the design, development, and integration of structural materials that can withstand extreme environments, such as high temperatures, radiation damage, and corrosion. High-entropy alloys (HEAs) are a class of structural materials in which suitable chemical elements in four or more numbers are mixed to typically produce single-phase concentrated solid solution alloys (CSAs). Many of these alloys exhibit good radiation tolerance like limited void swelling and hardening up to relatively medium radiation doses (tens of displacements per atom (dpa)); however, at higher radiation damage levels (>50 dpa), some HEAs suffer from considerable void swelling limiting their near-term acceptance for advanced nuclear reactor concepts. In this study, we developed a HEA containing a high density of Cu-rich nanoprecipitates distributed in the HEA matrix. The Cu-added HEA, NiCoFeCrCu_0.12, shows excellent void swelling resistance and negligible radiation-induced hardening upon irradiation up to high radiation doses (i.e., higher than 100 dpa). The void swelling resistance of the alloy is measured to be significantly better than NiCoFeCr CSA and austenitic stainless steels. Density functional theory simulations predict lower vacancy and interstitial formation energies at the coherent interfaces between Cu-rich nanoprecipitates and the HEA matrix. The alloy maintained a high sink strength achieved via nanoprecipitates and the coherent interface with the matrix at a high radiation dose (∼50 dpa). From our experiments and simulations, the effective recombination of radiation-produced vacancies and interstitials at the coherent interfaces of the nanoprecipitates is suggested to be the critical mechanism responsible for the radiation tolerance of the alloy. The materials design strategy based on incorporating a high density of interfaces can be applied to high-entropy alloy systems to improve their radiation tolerance.

Antimicrobial properties of a multi-component alloy

High traffic touch surfaces such as doorknobs, countertops, and handrails can be transmission points for the spread of pathogens, emphasizing the need to develop materials that actively self-sanitize. Metals are frequently used for these surfaces due to their durability, but many metals also possess antimicrobial properties which function through a variety of mechanisms. This work investigates metallic alloys comprised of several metals which individually possess antimicrobial properties, with the target of achieving broad-spectrum, rapid sanitation through synergistic activity. An entropy-motivated stabilization paradigm is proposed to prepare scalable alloys of copper, silver, nickel and cobalt. Using combinatorial sputtering, thin-film alloys were prepared on 100 mm wafers with ≈50% compositional grading of each element across the wafer. The films were then annealed and investigated for alloy stability. Antimicrobial activity testing was performed on both the as-grown alloys and the annealed films using four microorganisms-Phi6, MS2, Bacillus subtilis and Escherichia coli-as surrogates for human viral and bacterial pathogens. Testing showed that after 30 s of contact with some of the test alloys, Phi6, an enveloped, single-stranded RNA bacteriophage that serves as a SARS-CoV-2 surrogate, was reduced up to 6.9 orders of magnitude (> 99.9999%). Additionally, the non-enveloped, double-stranded DNA bacteriophage MS2, and the Gram-negative E. coli and Gram-positive B. subtilis bacterial strains showed a 5.0, 6.4, and 5.7 log reduction in activity after 30, 20 and 10 min, respectively. Antimicrobial activity in the alloy samples showed a strong dependence on the composition, with the log reduction scaling directly with the Cu content. Concentration of Cu by phase separation after annealing improved activity in some of the samples. The results motivate a variety of themes which can be leveraged to design ideal antimicrobial surfaces.

Antibacterial property, corrosion and discoloration resistance of pure copper containing Zn or Ni

This study focused on the effects of Zn and Ni addition on the antibacterial properties and corrosion resistance of copper alloys. The antimicrobial properties of copper and copper alloys were evaluated using Escherichia coli ATCC 8739 bacterial strain by employing the overlay and plate counting methods. X-ray photoelectron spectroscopy (XPS) was used to analyze the surface composition of the alloy after contact with bacteria. A salt spray method was used to simulate an artificial sweat contact environment to test the discoloration and corrosion resistance of the alloy, and scanning electron microscopy (SEM) was used to analyze the film layer and surface material composition of the corroded samples. The addition of Ni reduced the antibacterial performance of pure copper; however, the antibacterial performance of the alloy remained fast and efficient after the addition of Zn. Moreover, the addition of Zn and Ni significantly improved the corrosion resistance and surface discoloration of copper alloys in artificial sweat environments. This study provided support for the future application of copper alloys as antimicrobial surface-contact materials with safer public and medical environments in the face of diseases spread by large populations.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s12598-022-02098-8.

Anti-pathogen stainless steel combating COVID-19

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) exhibits strong stability on conventional stainless steel (SS) surface, with infectious virus detected even after two days, posing a high risk of virus transmission via surface touching in public areas. In order to mitigate the surface toughing transmission, the present study develops the first SS with excellent anti-pathogen properties against SARS-COV-2. The stabilities of SARS-CoV-2, H1N1 influenza A virus (H1N1), and Escherichia coli (E.coli) on the surfaces of Cu-contained SS, pure Cu, Ag-contained SS, and pure Ag were investigated. It is discovered that pure Ag and Ag-contained SS surfaces do not display apparent inhibitory effects on SARS-CoV-2 and H1N1. In comparison, both pure Cu and Cu-contained SS with a high Cu content exhibit significant antiviral properties. Significantly, the developed anti-pathogen SS with 20 wt% Cu can distinctly reduce 99.75% and 99.99% of viable SARS-CoV-2 on its surface within 3 and 6 h, respectively. In addition, the present anti-pathogen SS also exhibits an excellent inactivation ability for H1N1 influenza A virus (H1N1), and Escherichia coli (E.coli). Interestingly, the Cu ion concentration released from the anti-pathogen SS with 10 wt% and 20 wt% Cu was notably higher than the Ag ion concentration released from Ag and the Ag-contained SS. Lift buttons made of the present anti-pathogen SS are produced using mature powder metallurgy technique, demonstrating its potential applications in public areas and fighting the transmission of SARS-CoV-2 and other pathogens via surface touching.

Antiviral properties of copper and its alloys to inactivate covid-19 virus: a review

Copper (Cu) and its alloys are prospective materials in fighting covid-19 virus and several microbial pandemics, due to its excellent antiviral as well as antimicrobial properties. Even though many studies have proved that copper and its alloys exhibit antiviral properties, this research arena requires further research attention. Several studies conducted on copper and its alloys have proven that copper-based alloys possess excellent potential in controlling the spread of infectious diseases. Moreover, recent studies indicate that these alloys can effectively inactivate the covid-19 virus. In view of this, the present article reviews the importance of copper and its alloys in reducing the spread and infection of covid-19, which is a global pandemic. The electronic databases such as ScienceDirect, Web of Science and PubMed were searched for identifying relevant studies in the present review article. The review starts with a brief description on the history of copper usage in medicine followed by the effect of copper content in human body and antiviral mechanisms of copper against covid-19. The subsequent sections describe the distinctive copper based material systems such as alloys, nanomaterials and coating technologies in combating the spread of covid-19. Overall, copper based materials can be propitiously used as part of preventive and therapeutic strategies in the fight against covid-19 virus.