Nitrous acid (HONO): An emerging indoor pollutant

Ppb-Level Self-Calibrating Ozone Detection Using a T-Type Multipass Enhanced Photoacoustic Sensor with a 9.46 μm Quantum Cascade Laser

A sensitive, real-time, and accurate ozone (O3) sensor system is developed based on the combination of multipass enhanced photoacoustic (MPPA) and direct multipass absorption spectroscopy with a mid-infrared quantum cascade laser (QCL). The QCL with an emission wavelength of 9.46 μm was used to probe the O3 absorption lines without interference from the absorption of water and carbon dioxide in the flowing mixtures. The MPPA sensor was constructed with a T-type cell composed of a vertical cylinder and a horizontal cavity which were designed as an acoustic resonator and for multipass absorption enhancement, respectively. By periodically on-off switching the modulation of the laser wavelength, rapidly switched measurements of direct absorption and PA spectra can be achieved for real-time and accurate calibrations of the second harmonic (2f) PA signals with the direct absorbance spectra of O3. Moreover, a detection limit of O3 of 6 ppb at an average time of 300 s was achieved, and a short sensor response time of 16 s was also obtained in the flow mixtures with a flow rate of 50 sccm. This work provides a reliable method for O3 detection with capabilities of parts-per-billion-level sensitivity and on-site real-time concentration calibration, thus holding promise for in situ ozone monitoring under various environments.

Modelling indoor radical chemistry during the HOMEChem campaign

In the indoor environment, occupants are exposed to air pollutants originating from continuous indoor sources and exchange with the outdoor air, with the highest concentration episodes dominated by activities performed indoors such as cooking and cleaning. Here we use the INdoor CHEMical model in Python (INCHEM-Py) constrained by measurements from the House Observations of Microbial and Environmental Chemistry (HOMEChem) campaign, to investigate the impact of a bleach cleaning event and cooking on indoor air chemistry. Measurements of the concentrations of longer-lived organic and inorganic compounds, as well as measured photolysis rates, have been used as input for the model, and the modelled hydroxyl (OH) radicals, hydroperoxyl radicals, and nitrous acid (HONO) concentrations compared to the measured values. The peak modelled OH, , and HONO concentrations during cooking and cleaning activities are about 30%, 10%, and 30% higher than the observations, respectively, within experimental uncertainties. We have determined rates for the rapid loss of HONO formed through cooking activities onto a wet surface during the cleaning events and also for the subsequent slow release of HONO from the cleaned surface back into the gas-phase. Using INCHEM-Py we have also predicted peak concentrations of chlorine (Cl) atoms, (0.75-2.3) × 105 atom per cm3 at the time of cleaning. Model predictions of the Cl atom and OH radical reactivities were also explored, showing high Cl atom reactivity throughout the day, peaking around 5000-9000 s-1. The OH reactivity was found to increase from a background value close to urban outdoor levels of 20-40 s-1, to levels exceeding observations in outdoor polluted areas following cooking and cleaning activities (up to 160 s-1). This underlines the high oxidation capacity of the indoor atmospheric environment through determining the abundance of volatile organic compounds.

Socioeconomic disparities in mortality from indoor air pollution: A multi-country study

BACKGROUND

Indoor air pollution is a major public health concern, contributing to approximately 2.9 million deaths and 81.1 million disability-adjusted life years lost annually. This issue disproportionately affects underprivileged communities that depend on solid fuels for cooking. As a result, these communities suffer from heightened exposure to indoor air pollutants, which increases the risk of morbidity, mortality, and worsening health disparities.

OBJECTIVE

This study investigates the association between socioeconomic status and mortality related to indoor air pollution across multiple countries.

METHODS

Data from the 2019 Demographic and Health Survey, WHO, and World Bank were utilized to examine the impact of socioeconomic status on indoor air pollution-related mortality. The primary outcome was mortality associated with solid fuel use, with income quintiles as the independent variable. Linear and logistic regression analyses were applied to assess these relationships.

RESULTS

Logistic regression analysis revealed a strong negative association where household income increases and indoor air pollution-related mortality significantly decreases. Specifically, Households in the highest income quartile showed a 22% reduction progressively in the odds of mortality risk compared to the lowest income quintile. Additionally, access to clean fuel correlated with a 0.59 times lower odds of mortality, highlighting the clean energy sources' protecting effect.

CONCLUSION

The findings highlight the critical need to prioritize clean fuel access, particularly in low-income communities, to reduce indoor air pollution mortality. Policies should focus on increasing clean energy accessibility and supporting vulnerable populations through targeted subsidies and poverty alleviation programs to reduce indoor air pollution exposure disparities.

Nitrous Acid (HONO) Dissociation on the Water and Ice Surface: An Ab Initio Molecular Dynamics Study

In the atmosphere, the photodissociation of HONO is a significant source of OH radicals after ozone. In the present study, using Born-Oppenheimer molecular dynamics, we showed that HONO can dissociate on ice and water surfaces without light. In addition, the dissociation time of HONO is found to be much less on the ice surface compared to the same time on the water droplets.

A review of indoor nitrous acid (HONO) pollution: Measurement techniques, pollution characteristics, sources, and sinks

Indoor air quality is of major concern for human health and well-being. Nitrous acid (HONO) is an emerging indoor pollutant, and its indoor mixing ratios are usually higher than outdoor levels, ranging from a few to tens of parts per billion (ppb). HONO exhibits adverse effects to human health due to its respiratory toxicity and mutagenicity. Additionally, HONO can easily undergo photodissociation by ultraviolet light to produce hydroxyl radicals (OH•), which in turn trigger a series of further photochemical oxidation reactions of primary or secondary pollutants. The accumulation of indoor HONO can be attributed to both direct emissions from combustion sources, such as cooking, and secondary formation resulting from enhanced heterogeneous reactions of NOx on indoor surfaces. During the day, the primary sink of indoor HONO is photolysis to OH• and NO. Moreover, adsorption and/or reaction on indoor surfaces, and diffusion to the outside atmosphere contribute to HONO loss both during the day and at night. The level of indoor HONO is also affected by human occupancy, which can influence household factors such as temperature, humidity, light irradiation, and indoor surfaces. This comprehensive review article summarized the research progress on indoor HONO pollution based on indoor air measurements, laboratory studies, and model simulations. The environmental and health effects were highlighted, measurement techniques were summarized, pollution levels, sources and sinks, and household influencing factors were discussed, and the prospects in the future were proposed.

Photochemical renoxification on commercial indoor photoactive paint

Surface chemistry plays an important role in the indoor environment owing to the large indoor surface to volume ratio. This study explores the photoreactivity of surfaces painted with a photoactive paint in the presence of NOx. Two types of experiments are performed; illumination of painted surfaces with a nitrate deposit and illumination of painted surfaces in the presence of gaseous NO. For both types of experiments, illumination with a fluorescent bulb causes the greatest change in measured gaseous NOx concentrations. Results show that relative humidity and paint composition play an important role in the photoreactivity of indoor painted surfaces. Painted surfaces could contribute to gas-phase oxidant concentrations indoors.

Hydrogen peroxide emissions from surface cleaning in a single-family residence

High levels of reactive chemicals may be emitted to the indoor air during household surface cleaning, leading to poorer air quality and potential health hazards. Hydrogen peroxide (H₂O₂)-based cleaners have gained popularity in recent years, especially in times of COVID-19. Still, little is known regarding the effects of H₂O₂ cleaning on indoor air composition. In this work we monitored time-resolved H₂O₂ concentrations during a cleaning campaign in an occupied single-family residence using a cavity ring-down spectroscopy (CRDS) H₂O₂ analyzer. During the cleaning experiments, we investigated how unconstrained (i.e., "real-life") surface cleaning with a hydrogen peroxide solution influenced the indoor air quality of the house, and performed controlled experiments to investigate factors that could influence H₂O₂ levels including surface area and surface material, ventilation, and dwell time of the cleaning solution. Mean peak H₂O₂ concentrations observed following all surface cleaning events were 135 ppbv. The factors with the greatest effect on H₂O₂ levels were distance of the cleaned surface from the detector inlet, type of surface cleaned, and solution dwell time.

Ozone Decontamination of Medical and Nonmedical Devices: An Assessment of Design and Implementation Considerations

The control of infectious diseases can be improved via carefully designed decontamination equipment and systems. Research interest in ozone (a powerful antimicrobial agent) has significantly increased over the past decade. The COVID-19 pandemic has also instigated the development of new ozone-based technologies for the decontamination of personal protective equipment, surfaces, materials, and indoor environments. As this interest continues to grow, it is necessary to consider key factors affecting the applicability of lab-based findings to large-scale systems utilizing ozone. In this review, we present recent developments on the critical factors affecting the successful deployments of industrial ozone technologies. Some of these include the medium of application (air or water), material compatibility, efficient circulation and extraction, measurement and control, automation, scalability, and process economics. We also provide a comparative assessment of ozone relative to other decontamination methods/sterilization technologies and further substantiate the necessity for increased developments in gaseous and aqueous ozonation. Modeling methodologies, which can be applied for the design and implementation of ozone contacting systems, are also presented in this review. Key knowledge gaps and open research problems/opportunities are extensively covered including our recommendations for the development of novel solutions with industrial importance.

Measurements of Hydroxyl Radical Concentrations during Indoor Cooking Events: Evidence of an Unmeasured Photolytic Source of Radicals

The hydroxyl radical (OH) is the dominant oxidant in the outdoor environment, controlling the lifetimes of volatile organic compounds (VOCs) and contributing to the growth of secondary organic aerosols. Despite its importance outdoors, there have been relatively few measurements of the OH radical in indoor environments. During the House Observations of Microbial and Environmental Chemistry (HOMEChem) campaign, elevated concentrations of OH were observed near a window during cooking events, in addition to elevated mixing ratios of nitrous acid (HONO), VOCs, and nitrogen oxides (NOX). Particularly high concentrations were measured during the preparation of a traditional American Thanksgiving dinner, which required the use of a gas stove and oven almost continually for 6 h. A zero-dimensional chemical model underpredicted the measured OH concentrations even during periods when direct sunlight illuminated the area near the window, which increases the rate of OH production by photolysis of HONO. Interferences with measurements of nitrogen dioxide (NO2) and ozone (O3) suggest that unmeasured photolytic VOCs were emitted during cooking events. The addition of a VOC that photolyzes to produce peroxy radicals (RO2), similar to pyruvic acid, into the model results in better agreement with the OH measurements. These results highlight our incomplete understanding of the nature of oxidation in indoor environments.

The Effect of Human Occupancy on Indoor Air Quality through Real-Time Measurements of Key Pollutants

The primarily emitted compounds by human presence, e.g., skin and volatile organic compounds (VOCs) in breath, can react with typical indoor air oxidants, ozone (O₃), and hydroxyl radicals (OH), leading to secondary organic compounds. Nevertheless, our understanding about the formation processes of the compounds through reactions of indoor air oxidants with primary emitted pollutants is still incomplete. In this study we performed real-time measurements of nitrous acid (HONO), nitrogen oxides (NO_x = NO + NO₂), O₃, and VOCs to investigate the contribution of human presence and human activity, e.g., mopping the floor, to secondary organic compounds. During human occupancy a significant increase was observed of 1-butene, isoprene, and d-limonene exhaled by the four adults in the room and an increase of methyl vinyl ketone/methacrolein, methylglyoxal, and 3-methylfuran, formed as secondary compounds through reactions of OH radicals with isoprene. Intriguingly, the level of some compounds (e.g., m/z 126, 6-methyl-5-hepten-2-one, m/z 152, dihydrocarvone, and m/z 194, geranyl acetone) formed through reactions of O₃ with the primary compounds was higher in the presence of four adults than during the period of mopping the floor with commercial detergent. These results indicate that human presence can additionally degrade the indoor air quality.

Gas-Phase Nitrous Acid (HONO) Is Controlled by Surface Interactions of Adsorbed Nitrite (NO2-) on Common Indoor Material Surfaces

Nitrous acid (HONO) is a household pollutant exhibiting adverse health effects and a major source of indoor OH radicals under a variety of lighting conditions. The present study focuses on gas-phase HONO and condensed-phase nitrite and nitrate formation on indoor surface thin films following heterogeneous hydrolysis of NO₂, in the presence and absence of light, and nitrate (NO₃^-) photochemistry. These thin films are composed of common building materials including zeolite, kaolinite, painted walls, and cement. Gas-phase HONO is measured using an incoherent broadband cavity-enhanced ultraviolet absorption spectrometer (IBBCEAS), whereby condensed-phase products, adsorbed nitrite and nitrate, are quantified using ion chromatography. All of the surface materials used in this study can store nitrogen oxides as nitrate, but only thin films of zeolite and cement can act as condensed-phase nitrite reservoirs. For both the photo-enhanced heterogeneous hydrolysis of NO₂ and nitrate photochemistry, the amount of HONO produced depends on the material surface. For zeolite and cement, little HONO is produced, whereas HONO is the major product from kaolinite and painted wall surfaces. An important result of this study is that surface interactions of adsorbed nitrite are key to HONO formation, and the stronger the interaction of nitrite with the surface, the less gas-phase HONO produced.

Effect of Different Combustion Processes on Atmospheric Nitrous Acid Formation Mechanisms: A Winter Comparative Observation in Urban, Suburban and Rural Areas of the North China Plain

Atmospheric nitrous acid (HONO) is a dominant precursor of hydroxyl (OH) radicals, and its formation mechanisms are still controversial. Few studies have simultaneously explored effects of different combustion processes on HONO sources. Hereby, synchronous HONO measurement in urban (BJ), suburban (XH) and rural (DBT) areas with different combustion processes is performed in the North China Plain in winter. A box model is utilized to analyze HONO formation mechanisms. HONO concentration is the highest at the DBT site (2.51 ± 1.90 ppb), followed by the XH (2.18 ± 1.95 ppb) and BJ (1.17 ± 1.20 ppb) sites. Vehicle exhaust and coal combustion significantly contribute to nocturnal HONO at urban and rural sites, respectively. During a stagnant pollution period, the NO+OH reaction and combustion emissions are more crucial to HONO in urban and rural areas; meanwhile, the heterogeneous reaction of NO₂ is more significant in suburban areas. Moreover, the production rate of OH from HONO photolysis is about 2 orders of magnitude higher than that from ozone photolysis. Consequently, vehicle exhaust and coal combustion can effectively emit HONO, further causing environmental pollution and health risks. It is necessary to expand the implementation of the clean energy transition policy in China, especially in areas with substantial coal combustion.

Measurement and evaluation of gaseous and particulate emissions from burning scented and unscented candles

It has been known for a long time that incomplete combustion processes produce by-products that are harmful to human health. Particularly high concentrations of such by-products can arise in indoor environments when operating open flames without venting. The emission behavior of many combustion sources, including candles, has already been examined in detail. However, to date there are no studies in which the chemical composition of the candles is known exactly or where the candles were specifically manufactured for comparative measurements. In this respect, the study presented here, which was designed in collaboration with candle manufacturers and fragrance houses, demonstrates new insights into the emissions of burning candles depending on their composition. All investigations were carried out under controlled climatic conditions in an 8 m³ stainless steel chamber. Combinations of four different fuels (waxes) and five different fragrances in addition to one set of unscented control candles were examined. This resulted in 24 experiments, 20 with scented candles and four with unscented candles. The typical combustion gases carbon monoxide, carbon dioxide and NO_x, organic compounds, such as formaldehyde, benzene, and polycyclic aromatic hydrocarbons, PM_2.5 and ultrafine particles were monitored in the chamber air and the emission rates were determined. The data were statistically evaluated using parametric and non-parametric methods as well as hierarchical cluster analysis. Exposure scenarios typical for indoor environments were calculated from the emission rates and the results were compared with indoor guidance and reference values. As expected, a multitude of gaseous and particulate emissions were detected. These were typical combustion products as well as evaporated constituents of the fragrance mixtures. In most cases, the calculated indoor concentrations were well below the respective guidance and reference values. The exceptions observed in some cases for nitrogen dioxide, acrolein and benzo[a]pyrene are discussed critically.

A boron dipyrromethene (BODIPY) based probe for selective passive sampling of atmospheric nitrous acid (HONO) indoors

People spend up to 90% of their time indoors, and yet our understanding of indoor air quality and the chemical processes driving it are poorly understood, despite levels of key pollutants typically being higher indoors compared to outdoors. Nitrous acid (HONO) is a species that drives these indoor chemical processes, with potentially detrimental health effects. In this work, a BODIPY-based probe was synthesized with the aim of developing the first selective passive sampler for atmospheric HONO. Our probe and its products are easily detected by UV-Vis spectroscopy with molar extinct coefficients of 37 863 and 33 787 M^-1 cm^-1, respectively, and a detection limit of 14.8 ng mL^-1. When protonated, the probe fluoresces with a quantum yield of 33%, which is turned off upon reaction. The synthesized BODIPY probe was characterized using NMR and UV-Vis spectroscopy. Products were characterized by UV-Vis and ultra high-resolution mass spectrometry. The reaction kinetics of the probe with nitrite was studied using UV-Vis spectroscopy, which had a pseudo-first-order rate of k = 7.7 × 10^-4 s^-1. The rapid reaction makes this probe suitable for targeted ambient sampling of HONO. This was investigated through a proof-of-concept experiment with gaseous HONO produced by a custom high-purity calibration source delivering the sample to the BODIPY probe in an acidic aqueous solution in clean air and a real indoor air matrix. The probe showed quantitative uptake of HONO in both cases to form the same products observed from reaction with nitrite, with no indication of interferences from ambient NO or NO₂. The chemical and physical characteristics of the probe therefore make it ideal for use in passive samplers for selective sampling of HONO from the atmosphere.

HONO Production from Gypsum Surfaces Following Exposure to NO2 and HNO3: Roles of Relative Humidity and Light Source

Nitrous acid (HONO) is a toxic household pollutant and a major source of indoor OH radicals. The high surface-to-volume ratio and diverse lighting conditions make the indoor photochemistry of HONO complex. This study demonstrates surface uptake of NO₂ and gaseous HNO₃ followed by gas-phase HONO generation on gypsum surfaces, model system for drywall, under reaction conditions appropriate for an indoor air environment. Tens of parts per billion of steady-state HONO are detected under these experimental conditions. Mechanistic insight into this heterogeneous photochemistry is obtained by exploring the roles of material compositions, relative humidities, and light sources. NO₂ and HNO₃ are adsorbed onto drywall surfaces, which can generate HONO under illumination and under dark conditions. Photoenhanced HONO generation is observed for illumination with a solar simulator as well as with the common indoor light sources such as compact fluorescence light and incandescent light bulbs. Incandescent light sources release more HONO and NO₂ near the light source compared to the solar radiation. Overall, HONO production on the gypsum surface increases with the increase of RH up to 70% relative humidity; above that, the gaseous HONO level decreases due to surface loss. Heterogeneous hydrolysis of NO₂ is predicted to be the dominant HONO generation channel, where NO₂ is produced through the photolysis of surface-adsorbed nitrates. This hydrolysis reaction predominantly occurs in the first layer of surface-adsorbed water.

Indoor heterogeneous photochemistry of furfural drives emissions of nitrous acid

People spend approximately 80% of their time indoor, making the understanding of the indoor chemistry an important task for safety. The high surface-area-to-volume ratio characteristic of indoor environments leads the semi-volatile organic compounds (sVOCs) to deposit on the surfaces. Using a long path absorption photometer (LOPAP), this work investigates the formation of nitrous acid (HONO) through the photochemistry of adsorbed nitrate anions and its enhancement by the presence of furfural. Using a high-resolution proton-transfer-reaction time-of-flight mass spectrometer (PTR-TOF-MS), this work also investigates the surface emissions of VOCs from irradiated films of furfural and a mix of furfural and nitrate anions. Among the emitted VOCs, 2(5H)-furanone/2-Butenedial was observed at high concentrations, leading to maleic anhydride formation after UV irradiation. Moreover, the addition of potassium nitrate to the film formed NO_x and HONO concentrations up to 10 ppb, which scales to ca. 4 ppb for realistic indoor conditions. This work helps to understand the high levels of HONO and NO_x measured indoors.

Nitrosamine formation from the reaction of methamphetamine with gaseous nitrous acid

Methamphetamine is the most commonly seized amphetamine-type stimulant (ATS) worldwide. Chemical residues associated with the use or manufacture of methamphetamine can persist in the air and surfaces in a property for over 5 years and potentially pose risks to the health and safety of the public. When a house is tested for contamination, the test focuses on the presence of surface methamphetamine residue; however, other hazardous chemicals may also be present, including methamphetamine precursors and reaction products. As little has been reported about the ageing of the methamphetamine inside dwellings, there is currently large uncertainty regarding its fate and/or degradation products in such environments. If the indoor reactivity of methamphetamine is similar to that of nicotine-derived third-hand smoke, the production of a carcinogenic nitrosamine is an expected result. Thus, this proof-of-concept study investigated the reaction of methamphetamine with the common gaseous indoor oxidant nitrous acid (HONO) and monitored the fate of the resulting reaction products in simulated laboratory experiments to further understand the potential health risks associated with contaminated properties. Surface methamphetamine residue was observed to decrease with an exponential decay with an upper limit of 2.38 ± 0.5 × 10^-3 min^-1 upon exposure to HONO gas (5.7 ppmv, 0.25 L min^-1 ). N-nitrosomethamphetamine (NMA), a suspected human mutagen and carcinogen, was detected to have a steady-state formation over the sampling time frame, with a surface area concentration of 0.87 μg/100 cm² , suggesting that the risks to public health for properties contaminated with methamphetamine may be currently underestimated.

Loss of NO(g) to painted surfaces and its re-emission with indoor illumination

Heterogeneous surface reactions play a key role in the chemistry of the indoor environment because of the large indoor surface-to-volume ratio. The presence of photocatalytic material in indoor paints may allow photochemical reactions to occur at wavelengths of light that are present indoors. One such potential reaction is the heterogeneous photooxidation of NO to HONO. NO(g) is commonly found indoors, originating from combustion sources, ventilation and infiltration of outdoor air. We studied the interaction of NO(g) with painted surfaces illuminated with indoor fluorescent and incandescent lighting. There is a loss of NO(g) to painted surfaces in the dark at both 0 and 50% RH. At 50% RH, there is a re-release of some of that NO(g) under illumination. The same behavior is observed for illumination of different colored paints. This is in contrast to what is seen with TiO₂ as the substrate, where photoenhanced uptake of NO(g) and formation of NO₂ (g) are observed. We hypothesize that the loss of NO(g) is due to adsorption and diffusion into the paint. The re-release of NO under illumination is thought to be due to photooxidation of NO to HONO on the painted surface at higher relative humidities and subsequent HONO photolysis.

Indoor Air Quality and Passive E-cigarette Aerosol Exposures in Vape-Shops

INTRODUCTION

Direct emissions of nicotine and harmful chemicals from electronic cigarettes (e-cigarettes) have been intensively studied, but secondhand and thirdhand e-cigarette aerosol (THA) exposures in indoor environments are understudied.

AIMS AND METHODS

Indoor CO2, NO2, particulate matter (PM2.5), aldehydes, and airborne nicotine were measured in five vape-shops to assess secondhand exposures. Nicotine and tobacco-specific nitrosamines were measured on vape-shop surfaces and materials (glass, paper, clothing, rubber, and fur ball) placed in the vape-shops (14 days) to study thirdhand exposures.

RESULTS

Airborne PM2.5, formaldehyde, acetaldehyde, and nicotine concentrations during shop opening hours were 21, 3.3, 4.0, and 3.8 times higher than the levels during shop closing hours, respectively. PM2.5 concentrations were correlated with the number of e-cigarette users present in vape-shops (ρ = 0.366-0.761, p < .001). Surface nicotine, 4-(N-methyl-N-nitrosamino)-4-(3-pyridyl)butanal (NNA), and 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) were also detected at levels of 223.6 ± 313.2 µg/m2, 4.78 ± 11.8 ng/m2, and 44.8 ± 102.3 ng/m2, respectively. Substantial amounts of nicotine (up to 2073 µg/m2) deposited on the materials placed within the vape-shops, and NNA (up to 474.4 ng/m2) and NNK (up to 184.0 ng/m2) were also formed on these materials. The deposited nicotine concentrations were strongly correlated with the median number of active vapers present in a vape-shop per hour (ρ = 0.894-0.949, p = .04-.051). NNK levels on the material surfaces were significantly associated with surface nicotine levels (ρ=0.645, p = .037).

CONCLUSIONS

Indoor vaping leads to secondhand and THA exposures. Thirdhand exposures induced by e-cigarette vaping are comparable or higher than that induced by cigarette smoking. Long-term studies in various microenvironments are needed to improve our understanding of secondhand and THA exposures.

IMPLICATIONS

This study adds new convincing evidence that e-cigarette vaping can cause secondhand and THA exposures. Our findings can inform Occupational Safety and Health Administration, state authorities, and other government agencies regarding indoor air policies related to e-cigarette use, particularly in vape-shops. There is an urgent need to ensure that vape-shops maintain suitable ventilation systems and cleaning practices to protect customers, employees, and bystanders. Our study also demonstrates that nicotine can deposit or be adsorbed on baby's clothes and toys, and that tobacco-specific nitrosamines can form and retain on baby's clothes, highlighting children's exposure to environmental e-cigarette aerosol and THA at home is of a particular concern.

Unexpectedly High Indoor HONO Concentrations Associated with Photochemical NO2 Transformation on Glass Windows

Nitrous acid (HONO) is an important gaseous pollutant contributing to indoor air pollution because it causes adverse health effects and is the main source of hydroxyl radicals (OH). Here, we present direct measurements of HONO produced through light-induced heterogeneous reactions of NO₂ with grime adsorbed on glass window. The uptake coefficients of NO₂ [γ(NO₂)] on the glass plates from the kitchen increased markedly from (2.3 ± 0.1) × 10^-6 at 0% RH to (4.1 ± 0.5) × 10^-6 at 90% RH. We report a significant quantity of daytime HONO produced in the kitchen, compared to the living room and bedroom. Kinetic modeling suggests that phase state and bulk diffusivity play important roles in the NO₂ uptake; the best fit to the measured uptake coefficients is obtained with fixed diffusion coefficients. Photon scattering may be occurring at the surface of the films, leading to enhanced photon-excitation rates of polycyclic aromatic hydrocarbons. By taking these effects into account, the results from this study indicate that the HONO yields obtained in this study can explain the missing HONO in the photochemical models describing the indoor air chemistry.

Indoor Surface Chemistry: Developing a Molecular Picture of Reactions on Indoor Interfaces

Chemical reactions on indoor surfaces play an important role in air quality in indoor environments, where humans spend 90% of their time. We focus on the challenges of understanding the complex chemistry that takes place on indoor surfaces and identify crucial steps necessary to gain a molecular-level understanding of environmental indoor surface chemistry: (1) elucidate key surface reaction mechanisms and kinetics important to indoor air chemistry, (2) define a range of relevant and representative surfaces to probe, and (3) define the drivers of surface reactivity, particularly with respect to the surface composition, light, and temperature. Within the drivers of surface composition are the roles of adsorbed/absorbed water associated with indoor surfaces and the prevalence, inhomogeneity, and properties of secondary organic films that can impact surface reactivity. By combining laboratory studies, field measurements, and modeling we can gain insights into the molecular processes necessary to further our understanding of the indoor environment.

Cooking, Bleach Cleaning, and Air Conditioning Strongly Impact Levels of HONO in a House

The relative importance of common activities on indoor nitrous acid (HONO) mixing ratios was explored during high time resolution, month-long measurements by chemical ionization mass spectrometry in a previously unoccupied house. Indoor HONO varied from 0.2 to 84.0 ppb (mean: 5.5 ppb; median 3.8 ppb), an order of magnitude higher than simultaneously measured outdoor values, indicating important indoor sources. They agree well with simultaneous measurements of HONO by Laser-Photofragmentation/Laser-Induced Fluorescence. Before any combustion activities, the mixing ratio of 3.0 ± 0.3 ppb is indicative of secondary sources such as multiphase formation from NO₂. Cooking (with propane gas), especially the use of an oven, led to significant enhancements up to 84 ppb, with elevated mixing ratios persisting for a few days due to slow desorption from indoor surface reservoirs. Floor bleach cleaning led to prolonged, substantial decreases of up to 71-90% due to reactive processes. Air conditioning modulated HONO mixing ratios driven by condensation to wet surfaces in the AC unit. Enhanced ventilation also significantly lowered mixing ratios. Other conditions including human occupancy, ozone addition, and cleaning with terpene, natural product, and vinegar cleaners had a much smaller influence on HONO background levels measured following these activities.

Exposure to indoor air pollution across socio-economic groups in high-income countries: A scoping review of the literature and a modelling methodology

Disparities in outdoor air pollution exposure between individuals of differing socio-economic status is a growing area of research, widely explored in the environmental health literature. However, in developed countries, around 80% of time is spent indoors, meaning indoor air pollution may be a better proxy for personal exposure. Building characteristics - such as build quality, volume and ventilation - and occupant behaviour, mean indoor air pollution may also vary across socio-economic groups, leading to health inequalities. Much of the existing literature has focused on inequalities in exposure to outdoor air pollution, and there is thus a lack of an evidence base reviewing data for indoor environments. In this study, a scoping review of the literature on indoor air pollution exposures across different socio-economic groups is performed, examining evidence from both monitoring and modelling studies in the developed world. The literature was reviewed, identifying different indoor pollutants, definitions for socio-economic status and pre- and post- housing interventions. Based on the review, the study proposes a modelling methodology for evaluating the effects of environmental policies on different socio-economic populations. Using a sample size calculation, obstacles in obtaining sufficiently large samples of monitored data are demonstrated. A modelling framework for the rapid quantification of daily home exposure is then outlined as a proof of concept. While significant additional research is required to examine inequalities in indoor exposures, modelling approaches may provide opportunities to quantify exposure disparities due to housing and behaviours across populations of different socio-economic status.

Evaluation and impact factors of indoor and outdoor gas-phase nitrous acid under different environmental conditions

As an important indoor pollutant, nitrous acid (HONO) can contribute to the concentration of indoor OH radicals by photolysis via sunlight penetrating into indoor environments, thus affecting the indoor oxidizing capability. In order to investigate the concentration of indoor HONO and its impact factors, three different indoor environments and two different locations in urban and suburban areas were selected to monitor indoor and outdoor pollutants simultaneously, including HONO, NO, NO₂, nitrogen oxides (NO_x), O₃, and particle mass concentration. In general, the concentration of indoor HONO was higher than that outdoors. In the urban area, indoor HONO with high average concentration (7.10 ppbV) was well-correlated with the temperature. In the suburban area, the concentration of indoor HONO was only about 1-2 ppbV, and had a good correlation with indoor relative humidity. It was mainly attributed to the heterogeneous reaction of NO₂ on indoor surfaces. The sunlight penetrating into indoor environments from outside had a great influence on the concentration of indoor HONO, leading to a concentration of indoor HONO close to that outdoors.

Indoor acids and bases

Numerous acids and bases influence indoor air quality. The most abundant of these species are CO₂ (acidic) and NH₃ (basic), both emitted by building occupants. Other prominent inorganic acids are HNO₃ , HONO, SO₂ , H₂ SO₄ , HCl, and HOCl. Prominent organic acids include formic, acetic, and lactic; nicotine is a noteworthy organic base. Sources of N-, S-, and Cl-containing acids can include ventilation from outdoors, indoor combustion, consumer product use, and chemical reactions. Organic acids are commonly more abundant indoors than outdoors, with indoor sources including occupants, wood, and cooking. Beyond NH₃ and nicotine, other noteworthy bases include inorganic and organic amines. Acids and bases partition indoors among the gas-phase, airborne particles, bulk water, and surfaces; relevant thermodynamic parameters governing the partitioning are the acid-dissociation constant (K_a ), Henry's law constant (K_H ), and the octanol-air partition coefficient (K_oa ). Condensed-phase water strongly influences the fate of indoor acids and bases and is also a medium for chemical interactions. Indoor surfaces can be large reservoirs of acids and bases. This extensive review of the state of knowledge establishes a foundation for future inquiry to better understand how acids and bases influence the suitability of indoor environments for occupants, cultural artifacts, and sensitive equipment.

Unexpected formation of oxygen-free products and nitrous acid from the ozonolysis of the neonicotinoid nitenpyram

The neonicotinoid nitenpyram (NPM) is a multifunctional nitroenamine [(R₁N)(R₂N)C=CHNO₂] pesticide. As a nitroalkene, it is structurally similar to other emerging contaminants such as the pharmaceuticals ranitidine and nizatidine. Because ozone is a common atmospheric oxidant, such compounds may be oxidized on contact with air to form new products that have different toxicity compared to the parent compounds. Here we show that oxidation of thin solid films of NPM by gas-phase ozone produces unexpected products, the majority of which do not contain oxygen, despite the highly oxidizing reactant. A further surprising finding is the formation of gas-phase nitrous acid (HONO), a species known to be a major photolytic source of the highly reactive hydroxyl radical in air. The results of application of a kinetic multilayer model show that reaction was not restricted to the surface layers but, at sufficiently high ozone concentrations, occurred throughout the film. The rate constant derived for the O₃-NPM reaction is 1 × 10^-18 cm³⋅s^-1, and the diffusion coefficient of ozone in the thin film is 9 × 10^-10 cm²⋅s^-1 These findings highlight the unique chemistry of multifunctional nitroenamines and demonstrate that known chemical mechanisms for individual moieties in such compounds cannot be extrapolated from simple alkenes. This is critical for guiding assessments of the environmental fates and impacts of pesticides and pharmaceuticals, and for providing guidance in designing better future alternatives.

The impact of photocatalytic paint porosity on indoor NOx and HONO levels

Photocatalytic materials are a potentially effective remediation technology for indoor air purification.

Ten questions concerning the implications of carpet on indoor chemistry and microbiology

Carpet and rugs currently represent about half of the United States flooring market and offer many benefits as a flooring type. How carpets influence our exposure to both microorganisms and chemicals in indoor environments has important health implications but is not well understood. The goal of this manuscript is to consolidate what is known about how carpet impacts indoor chemistry and microbiology, as well as to identify the important research gaps that remain. After describing the current use of carpet indoors, questions focus on five specific areas: 1) indoor chemistry, 2) indoor microbiology, 3) resuspension and exposure, 4) current practices and future needs, and 5) sustainability. Overall, it is clear that carpet can influence our exposures to particles and volatile compounds in the indoor environment by acting as a direct source, as a reservoir of environmental contaminants, and as a surface supporting chemical and biological transformations. However, the health implications of these processes are not well known, nor how cleaning practices could be optimized to minimize potential negative impacts. Current standards and recommendations focus largely on carpets as a primary source of chemicals and on limiting moisture that would support microbial growth. Future research should consider enhancing knowledge related to the impact of carpet in the indoor environment and how we might improve the design and maintenance of this common material to reduce our exposure to harmful contaminants while retaining the benefits to consumers.

Understanding the Spatial Heterogeneity of Indoor OH and HO2 due to Photolysis of HONO Using Computational Fluid Dynamics Simulation

Indoor photolysis of nitrous acid (HONO) generates hydroxyl radicals (OH), and since OH is fast reacting, it may be confined within the HONO-photolyzing indoor volume of light. This study investigated the HONO-photolysis-induced formation of indoor OH, the transformation of OH to hydroperoxy radicals (HO₂), and resulting spatial distributions of those radicals and their oxidation products. To do so, a computational fluid dynamics (CFD) model framework was established to simulate HONO photolysis in a room and subsequent reactions associated with OH and HO₂ under a typical range of indoor lighting and ventilation conditions. The results showed that OH and HO₂ were essentially confined in the volume of HONO-photolyzing light, but oxidation products were relatively well distributed throughout the room. As the light volume increased, more total in-room OH was produced, thereby increasing oxidation product concentrations. Spatial distributions of OH and HO₂ varied by the type of artificial light (e.g., fluorescent versus incandescent), due to differences in photon flux as a function of light source and the distance from the source. The HO₂ generation rate and air change rate made notable impacts on product concentrations.

Human exposure to NO2 in school and office indoor environments

BACKGROUND

Although nitrogen dioxide (NO₂) is one of the most common air pollutants encountered indoors, and extensive literature has examined the link between NO₂ exposure and duration causing adverse respiratory effects in susceptible populations, information about global and local exposure to NO₂ in different indoor environments is limited. To synthesize the existing knowledge, this review analyzes the magnitude of and the trends in global and local exposure to NO₂ in schools and offices, and the factors that control exposure.

METHODS

For the literature review, Web of Science, SCOPUS, Google Scholar, and PubMed were searched using 42 search terms and their combinations to identify manuscripts, reports, and directives published between 1971 and 2019. The search was then extended to the reference lists of relevant articles.

RESULTS

The calculated median, as well as the mean, concentration of NO₂ in school (median 21.1 μg/m³; mean 29.4 μg/m³) and office settings (median 22.7 μg/m³; mean 25.1 μg/m³) was well below the World Health Organization (WHO) guideline of 40 μg/m³ for the annual mean NO₂ concentration. However, a large range of average concentrations of NO₂ were reported, from 6.00 to 68.5 μg/m³ and from 3.40 to 56.5 μg/m³ for school and office environments, respectively, indicating situations where the WHO guidelines are exceeded. Outdoor levels of NO₂ are a reliable predictor of indoor NO₂ levels across seasons, with mean and median Indoor/Outdoor (I/O) ratios of 0.9 and 0.7 in school and 0.9 and 0.8 in office environments, respectively. The absence of major indoor NO₂ emission sources and NO₂ sinks, including chemical reactions and deposition, are the reasons for lower indoor NO₂ concentrations. During the winter, outdoor NO₂ concentrations are generally higher than during the summer. In addition, various building and indoor environment characteristics, such as type of ventilation, air exchange rates, airtightness of the envelope, furnishing and surface characteristics of the building, location of the building (urban versus suburban and proximity to traffic routes), as well as occupants' behavior (such as opening windows), have been statistically significantly associated with indoor NO₂ levels in school and office environments.

CONCLUSIONS

Indoor exposure to NO₂ from the infiltration of ambient air can be significant in urban areas, and in the case of high traffic volume. Although reducing transportation emissions is challenging, there are several easier means to reduce indoor NO₂ concentrations, including a ventilation strategy with suitable filters; location planning of new schools, classrooms, and ventilating windows or intakes; traffic planning (location and density); and reducing the use of NO₂-releasing indoor sources.

Role of location, season, occupant activity, and chemistry in indoor ozone and nitrogen oxide mixing ratios

Understanding the oxidizing environment indoors is important for predicting indoor air quality and its impact on human health. We made continuous time-resolved measurements (30 s) of several oxidants and oxidant precursors (collectively referred to as oxidant*): ozone (O3), nitric oxide (NO), and NO2* - the sum of nitrogen dioxide (NO2) and nitrous acid (HONO). These species were measured in three indoor environments - an occupied residence, a chemistry laboratory, and an academic office - in Syracuse, New York, during two seasons in 2017 and 2018. Oxidant* levels differed greatly between the residence, the lab and the office. Indoor-to-outdoor ratios (I/O) of O3 were 0.03 and 0.67 in the residence and office; I/ONO (I/ONO2*) were 11.70 (1.26) in the residence and 0.13 (1.70) in the office. Little seasonal variability was observed in the lab and office, but O3 and NO2* levels in the residence were greater in spring than in winter, while NO levels were lower. Human activities such as cooking and opening patio doors resulted in large changes in oxidant* mixing ratios in the residence. In situ chamber experiments demonstrated that the increase in O3 and NO2* levels during door-open periods was due to a combination of physical mixing between indoor and outdoor air, gas-phase production of NO2 from O3-NO chemistry, and heterogeneous formation of HONO on indoor surfaces. Our results also highlight the importance of chemistry (with NO, alkenes, and surfaces) in O3 mixing ratios in the residence, especially during door-open periods.

Assessing indoor gas phase oxidation capacity through real-time measurements of HONO and NOx in Guangzhou, China

The hydroxyl radical (OH) is one of the most important oxidants controlling the oxidation capacity of the indoor atmosphere. One of the main OH sources indoors is the photolysis of nitrous acid (HONO). In this study, real-time measurements of HONO, nitrogen oxides (NOx) and ozone (O3) in an indoor environment in Guangzhou, China, were performed under two different conditions: (1) in the absence of any human activity and (2) in the presence of cooking. The maximum NOx and HONO levels drastically increased from 15 and 4 ppb in the absence of human activity to 135 and 40 ppb during the cooking event, respectively. The photon flux was determined for the sunlit room, which has a closed south-east oriented window. The photon flux was used to estimate the photolysis rate constants of NO2, J(NO2), and HONO, J(HONO), which span the range between 8 × 10-5 and 1.5 × 10-5 s-1 in the morning from 9:30 to 11:45, and 8.5 × 10-4 and 1.5 × 10-4 s-1 at noon, respectively. The OH concentrations calculated by photostationary state (PSS) approach, observed around noon, are very similar, i.e., 2.4 × 106 and 3.1 × 106 cm-3 in the absence of human activity and during cooking, respectively. These results suggest that under "high NOx" conditions (NOx higher than a few ppb) and with direct sunlight in the room, the NOx and HONO chemistry would be similar, independent of the geographic location of the indoor environment, which facilitates future modeling studies focused on indoor gas phase oxidation capacity.

Selective decontamination of the reactive air pollutant nitrous acid via node-linker cooperativity in a metal-organic framework

Nitrous acid (HONO) is a reservoir of NO x and an emerging pollutant having direct impacts on air quality, both in- and outdoors, as well as on human health. In this work, the amine-functionalized metal-organic framework (MOF), UiO-66-NH2, was investigated due to its potential to selectively decontaminate nitrous acid at environmentally relevant concentrations. UiO-66-NH2 proved to be effective in the removal of nitrous acid from a continuous gaseous stream. This is observed via the formation of an aryl diazonium salt that subsequently converts to a phenol with a concomitant release of nitrogen gas. This process is preceded via the formation of the nitrosonium cation (likely protonation from an acidic proton on the node). Thus, UiO-66-NH2 is capable of selectively converting the pollutant nitrous acid to benign products.

Time-Resolved Measurements of Indoor Chemical Emissions, Deposition, and Reactions in a University Art Museum

A 6-week study was conducted at the University of Colorado Art Museum, during which volatile organic compounds (VOCs), carbon dioxide (CO₂), ozone (O₃), nitric oxide (NO), nitrogen dioxide (NO₂), other trace gases, and submicron aerosol were measured continuously. These measurements were then analyzed using a box model to quantify the rates of major processes that transformed the composition of the air. VOC emission factors were quantified for museum occupants and their activities. The deposition of VOCs to surfaces was quantified across a range of VOC saturation vapor concentrations ( C*) and Henry's Law constants ( H) and determined to be a major sink for VOCs with C* < 10⁸ μg m^-3 and H > 10² M atm^-1. The reaction rates of VOCs with O₃, OH radicals, and nitrate (NO₃) radicals were quantified, with unsaturated and saturated VOCs having oxidation lifetimes of >5 and >15 h, making deposition to surfaces and ventilation the dominant VOC sinks in the museum. O₃ loss rates were quantified inside a museum gallery, where reactions with surfaces, NO, occupants, and NO₂ accounted for 62%, 31%, 5%, and 2% of the O₃ sink. The measured concentrations of acetic acid, formic acid, NO₂, O₃, particulate matter, sulfur dioxide, and total VOCs were below the guidelines for museums.

Impacts of potential HONO sources on the concentrations of oxidants and secondary organic aerosols in the Beijing-Tianjin-Hebei region of China

We first coupled indoor emissions and biomass burning emissions into the WRF-Chem model besides the other four potential HONO sources (i.e., traffic emissions, soil emissions, and heterogeneous reactions on aerosol and ground surfaces). Eight simulations were performed in the Beijing-Tianjin-Hebei region (BTH) of China in August of 2006. The results indicated that traffic emissions and heterogeneous reactions on ground and aerosol surfaces were the key sources of HONO at night, accounting for ~41%, ~27% and ~20% of the nighttime simulated HONO concentrations, respectively. The two heterogeneous reactions were the main contributors during the day, accounting for ~66% (ground surfaces) and ~19% (aerosol surfaces) of the daytime simulated HONO concentrations. The indoor emission source could be the second largest contributor during nighttime and led to a maximum hourly enhancement of 0.59 and 0.76 ppb at the central urban sites of Beijing and Tianjin, respectively. The six potential HONO sources enhanced the monthly meridional-mean concentrations of O₃, OH and HO₂ by 5-44%, 5~>150% and 5~>200%, respectively, leading to an enhancement of 1-3 μg m^-3 in the monthly averaged concentrations of secondary organic aerosol (SOA), and that of 10-35 μg m^-3 in the largest hourly concentrations of SOA within 1000 m above the ground in the BTH. The major precursors of the enhanced SOA were Xylenes, Toluene and BIGALK (lumped alkanes C > 3). The inclusion of the six potential HONO sources in the WRF-Chem model considerably improved the HONO simulations at both urban and suburban sites compared with the corresponding observations. The above results suggested that the six potential HONO sources significantly enhanced the atmospheric oxidation capacity and thus accelerated SOA chemical aging in the BTH of China, leading to large enhancements in the hourly SOA concentrations and aggravating haze events in this region.

Evidence for Gas-Surface Equilibrium Control of Indoor Nitrous Acid

Nitrous acid (HONO) is an important component of indoor air as a photolabile precursor to hydroxyl radicals and has direct health effects. HONO concentrations are typically higher indoors than outdoors, although indoor concentrations have proved challenging to predict using box models. In this study, time-resolved measurements of HONO and NO₂ in a residence showed that [HONO] varied relatively weakly over contiguous periods of hours, while [NO₂] fluctuated in association with changes in outdoor [NO₂]. Perturbation experiments were performed in which indoor HONO was depleted or elevated and were interpreted using a two-compartment box model. To reproduce the measurements, [HONO] had to be predicted using persistent source and sink processes that do not directly involve NO₂, suggesting that HONO was in equilibrium with indoor surfaces. Production of gas phase HONO directly from conversion of NO₂ on surfaces had a weak influence on indoor [HONO] during the time of the perturbations. Highly similar temporal responses of HONO and semivolatile carboxylic acids to ventilation of the residence along with the detection of nitrite on indoor surfaces support the concept that indoor HONO mixing ratios are controlled strongly by gas-surface equilibrium.

Human exposure to ozone in school and office indoor environments

BACKGROUND

Although it is recognized that ozone causes acute and chronic health effects and that even trace amounts of ozone are potentially deleterious to human health, information about global and local exposures to ozone in different indoor environments is limited. To synthesize the existing knowledge, this review analyzes the magnitude of and the trends in global and local exposure to ozone in schools and offices and the factors controlling the exposures.

METHODS

In conducting the literature review, Web of Science, SCOPUS, Google Scholar, and PubMed were searched using 38 search terms and their combinations to identify manuscripts, reports, and directives published between 1973 and 2018. The search was then extended to the reference lists of relevant articles.

RESULTS

The calculated median concentration of ozone both in school (8.50 μg/m³) and office (9.04 μg/m³) settings was well below the WHO guideline value of 100 μg/m³ as a maximum 8 h mean concentration. However, a large range of average concentrations of ozone was reported, from 0.8-114 μg/m³ and from 0 to 96.8 μg/m³ for school and office environments, respectively, indicating situations where the WHO values are exceeded. Outdoor ozone penetrating into the indoor environment is the main source of indoor ozone, with median I/O ratios of 0.21 and 0.29 in school and office environments, respectively. The absence of major indoor ozone sources and ozone sinks, including gas-phase reactions and deposition, are the reasons for lower indoor than outdoor ozone concentrations. However, there are indoor sources of ozone that are of significance in certain indoor environments, including printers, photocopiers, and many other devices and appliances designed for indoor use (e.g., air cleaners), that release ozone either intentionally or unintentionally. Due to significantly elevated outdoor ozone concentrations during summer, summer indoor concentrations are typically elevated. In addition, the age of a building and various housing aspects (carpeting, air conditioning, window fans, and window openings) have been significantly associated with indoor ozone levels.

CONCLUSIONS

The existing means for reducing ozone and ozone reaction products in school and office settings are as follows: 1) reduce penetration of outdoor ozone indoors by filtering ozone from the supply air; 2) limit the use of printers, photocopiers, and other devices and appliances that emit ozone indoors; 3) limit gas-phase reactions by limiting the use of materials and products (e.g. cleaning chemicals) the emissions of which react with ozone.

Time-Resolved Measurements of Nitric Oxide, Nitrogen Dioxide, and Nitrous Acid in an Occupied New York Home

Indoor oxidizing capacity in occupied residences is poorly understood. We made simultaneous continuous time-resolved measurements of ozone (O₃), nitric oxide (NO), nitrogen dioxide (NO₂), and nitrous acid (HONO) for two months in an occupied detached home with gas appliances in Syracuse, NY. Indoor NO and HONO mixing ratios were higher than those outdoors, whereas O₃ was much lower (sub-ppbv) indoors. Cooking led to peak NO, NO₂, and HONO levels 20-100 times greater than background levels; HONO mixing ratios of up to 50 ppbv were measured. Our results suggest that many reported NO₂ levels may have a large positive bias due to HONO interference. Nitrous acid, NO₂, and NO were removed from indoor air more rapidly than CO₂, indicative of reactive removal processes or surface uptake. We measured spectral irradiance from sunlight entering the residence through glass doors; hydroxyl radical (OH) production rates of (0.8-10) × 10⁷ molecules cm^-3 s^-1 were calculated in sunlit areas due to HONO photolysis, in some cases exceeding rates expected from ozone-alkene reactions. Steady-state nitrate radical (NO₃) mixing ratios indoors were predicted to be lower than 1.65 × 10⁴ molecules cm^-3. This work will help constrain the temporal nature of oxidant concentrations in occupied residences and will improve indoor chemistry models.

SO2 Initiates the Efficient Conversion of NO2 to HONO on MgO Surface

Nitrous acid (HONO) is an important source of hydroxyl radical (OH) that determines the fate of many chemically active and climate relevant trace gases. However, the sources and the formation mechanisms of HONO remain poorly understood. In this study, the effect of SO₂ on the heterogeneous reactions of NO₂ on MgO as a mineral dust surrogate was investigated. The reactivity of MgO to NO₂ is weak, while coexisting SO₂ can increase the uptake coefficients of NO₂ on MgO by 2-3 orders of magnitude. The uptake coefficients of NO₂ on SO₂-aged MgO are independent of NO₂ concentrations in the range of 20-160 ppbv and relative humidity (0-70%RH). The reaction mechanism was demonstrated to be a redox reaction between NO₂ and surface sulfite. In the presence of SO₂, NO₂ was reduced to nitrite under dry conditions, which could be further converted to gas-phase HONO in humid conditions. These results suggest that the reductive effect of SO₂ on the heterogeneous conversion of NO₂ to HONO may have a significant contribution to the unknown sources of HONO observed in polluted areas (for example, in China).

Emerging developments in the standardized chemical characterization of indoor air quality

Despite the fact that the special characteristics of indoor air pollution make closed environments quite different from outdoor environments, the conceptual ideas for assessing air quality indoors and outdoors are similar. Therefore, the elaboration of International Standards for air quality characterization in view of controlling indoor air quality should resort to this common basis. In this short review we describe the possibilities of standardization of tools dedicated to indoor air quality characterization with a focus on the tools permitting to study the indoor air chemistry. The link between indoor exposure and health as well as the critical processes driving the indoor air quality are introduced. Available International Standards for the assessment of indoor air quality are depicted. The standards comprise requirements for the sampling on site, the analytical procedures, and the determination of material emissions. To date, these standardized procedures assure that indoor air, settled dust and material samples are analyzed in a comparable manner. However, existing International Standards exclusively specify conventional, event-driven target-screening using discontinuous measurement methods for long-lived pollutants. Therefore, this review draws a parallel between physico-chemical processes in indoor and outdoor environments. The achievements in atmospheric sciences also improve our understanding of indoor environments. The community of atmospheric scientists can be both ideal and supporter for researchers in the area of indoor air quality characterization. This short review concludes with propositions for future standardization activities for the chemical characterization of indoor air quality. Future standardization efforts should focus on: (i) the elaboration of standardized measurement methods and measurement strategies for online monitoring of long-lived and short-lived pollutants, (ii) the assessment of the potential and the limitations of non-target screening, (iii) the paradigm shift from event-driven investigations to systematic approaches to characterize indoor environments, and (iv) the development of tools for policy implementation.

Introductory lecture: atmospheric chemistry in the Anthropocene

The term “Anthropocene” was coined by Professor Paul Crutzen in 2000 to describe an unprecedented era in which anthropogenic activities are impacting planet Earth on a global scale. Greatly increased emissions into the atmosphere, reflecting the advent of the Industrial Revolution, have caused significant changes in both the lower and upper atmosphere. Atmospheric reactions of the anthropogenic emissions and of those with biogenic compounds have significant impacts on human health, visibility, climate and weather. Two activities that have had particularly large impacts on the troposphere are fossil fuel combustion and agriculture, both associated with a burgeoning population. Emissions are also changing due to alterations in land use. This paper describes some of the tropospheric chemistry associated with the Anthropocene, with emphasis on areas having large uncertainties. These include heterogeneous chemistry such as those of oxides of nitrogen and the neonicotinoid pesticides, reactions at liquid interfaces, organic oxidations and particle formation, the role of sulfur compounds in the Anthropocene and biogenic–anthropogenic interactions. A clear and quantitative understanding of the connections between emissions, reactions, deposition and atmospheric composition is central to developing appropriate cost-effective strategies for minimizing the impacts of anthropogenic activities. The evolving nature of emissions in the Anthropocene places atmospheric chemistry at the fulcrum of determining human health and welfare in the future.

Indoor air quality at life and work environments in Rome, Italy

The air quality of three different microenvironments (school, dwelling, and coffee bar) located in the city of Rome, Italy, was assessed. Indoor and outdoor concentrations of polycyclic aromatic hydrocarbons (PAHs) associated with PM2.5 particles were determined during an intensive 3-week sampling campaign conducted in March 2013. In interiors, total particulate PAHs ranged from 1.53 to 4.96 ng/m(3) while outdoor air contained from 2.75 to 3.48 ng/m(3). In addition, gaseous toxicants, i.e., NO2, NOx , SO2, O3, and BTEX (benzene, toluene, ethyl-benzene, and xylene isomers), were determined both in internal and external air. To solve the origin of indoor and outdoor PAHs, several source apportionment methods were applied. Multivariate analysis revealed that emissions from motor vehicles, biomass burning for heating purposes, and soil resuspension were the major sources of PAHs in the city. No linear correlation was established between indoor and outdoor values for PM2.5 and BTEX; the respective indoor/outdoor concentration ratios exceed unity except for PM2.5 in the no smoking home and benzene in all school floors. This suggests that important internal sources such as tobacco smoking, cleaning products, and resuspension dust contributed to indoor pollution. Using the monitoring stations of ARPA Lazio regional network as reference, the percentage within PAH group of benzo[a]pyrene, which is the WHO marker for the carcinogenic risk estimates, was ca. 50% higher in all locations investigated.